Models: GDI-EXJMP1500...1520

User Guide

EcoJump

02 03

FCC STATEMENT:This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna, increase the separation between the equipment and receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, consult the dealer or an experienced radio/TV technician for help.

RF WARNING STATEMENT:The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC STATEMENT:This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1) This device may not cause interference, and

2) This device must accept any interference, including interference that may cause undesired operation of the device.

PRODUCT USE AND PROTECTION:Read and Follow all Instructions. Use only as intended.

The ECOXGEAR device is intended to be used indoors or outdoors and in land or water environments. The device has been tested to IP67 waterproofing standards. However, the device is not intended for constant underwater use.

Always make sure the cap(s) / covers(s) are clean, free from sand or debris and correctly fitted. The device will only meet IP67 ratings if all rubber seals, gasket(s) and cap(s) / covers(s) are in place. If your device is exposed to salt water clean it thoroughly after use with fresh water.

The USB cables, connections, and the unit with an improperly fitted or closed cap are NOT waterproof.

To prevent fire or shock, do NOT attempt to charge this unit if it is wet or you suspect water has entered the unit. In this situation, please return the unit to Grace Digital for a free assessment. If we have found that the unit has carried water we will repair or replace the unit free of charge.

SAFETY ADVISORY & WARNING:Read and Follow all Instructions. Use only as intended.

CAUTION: Do NOT open to repair. A qualified technician must carry out repair work.

ATTENTION: Do NOT charge while the unit is wet. Towel dry the unit AND make sure all connections are dry BEFORE plugging in the charging connector. Failure to do so may result in electrical damage to the unit and may void the warranty.

WARNING: This product may contain chemicals listed in Proposition 65 (www.oehha.ca.gov/prop65/prop65_list/Newlist.html)

WARNING: The unit has a built-in Lithium battery. The battery must NOT be used in or near an open heat source or excessive heat.

WARNING: Danger of explosion if battery is incorrectly replaced.

ATTENTION: Do NOT dispose of in a landfill. Contact Grace Digital at www.gracesupport.com or a certified recycling agent to dispose of the unit.

ATTENTION: AC adapter is a device forming a part of the main plug therefore the AC adapter can always be readily disconnected from AC socket-outlet.

WARNING: When using this product, basic precautions should always be followed, including the following:

a) To reduce the risk of injury, close supervision is necessary when the product is used near children.

b) Use of an attachment not recommended or sold by power pack manufacturer may result in a risk of fire, electric shock, or injury to persons.

c) Do not operate the power pack with a damaged cord or plug, or a damaged output cable.

SAVE THESE INSTRUCTIONS

04 05

SAFETY:This product has a limited life span of use and should be replaced when it shows obvious signs of wear.

Do not modify or remove any original component parts of the device. Doing so could cause damage to the unit allowing water to ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.

Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so could cause damage to the unit allowing water to ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.

You should always

1) Use the proper ECOXGEAR mounts if you intend to mount the unit.

2) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the internal components. Salt water / air is particularly corrosive. Always make sure that the gaskets are sealed when in a salt water environment and the unit properly rinsed off after use.

3) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt or water on them prior to storage or removing the cover.

4) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit.

5) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.

6) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the integrity of the unit to take on water.

You should never

1) Never charge your ECOXGEAR if you suspect water has entered the device. Charging a device with water inside could be potentially hazardous and cause fire or a spark.

2) Never use your ECOXGEAR if you have dropped it or thrown it against a hard surface, which may have destroyed the integrity of the housings, or gaskets. In the event of a severe impact to your unit please return the unit to Grace Digital to review for potential damage.

3) Never open the auxiliary doors in a water environment. This could cause water to ingress into the unit, which could potentially be hazardous and cause a fire or a spark.

4) Never attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs.

CARE, MAINTENANCE & PRECAUTIONS: 1) The unit is waterproof only when the caps are properly closed.

2) Close the caps properly before use. If the unit is placed in water without the caps properly closed, water may enter into the unit and void your warranty.

3) Dry unit completely before opening the caps. Do NOT open the caps if wet or in a wet environment.

4) Do NOT apply excessive force to any surfaces of the unit when wet or in a wet environment.

5) Do NOT use or store the unit in places with high temperature.

6) AVOID prolonged exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields.

7) Periodically check the rubber seal on the caps for premature wear.

8) Periodically clean the rubber with a soft moist cloth and ensure no objects such as dirt, hair, or sand are on the rubber seal ring. Do NOT use any oily solvent or chemicals for cleaning.

9) Rinse off the unit with tap water after use in salt water or swimming pool.

10) Power and / or charge the built-in rechargeable battery by connecting the USB cord to a computer USB connection or to the AC outlet using the AC-to-USB cord 5V, 2A power adapter intended for use with the unit.

11) Do NOT remove the built-in battery.

06 07

Control Buttons & Operations On/OffUnit will arrive powered OFF. PRESS AND HOLD the Power Button for approximately 2 seconds to power ON.

When ON, SHORT PRESS to put in Standby Mode. Short press again to turn unit ON. Keep in Standby Mode when unit is not in use to enable battery notifications.

When ON or in Standby Mode, PRESS AND HOLD for approximately 4 seconds to power OFF.

NOTE: The Bluetooth battery level and temperature notifications do NOT work when EcoJump is OFF. Refer to BLE and Smartphone App for details.

Power Indicator:• Solid BLUE Light - ON.• Flashing BLUE Light - Refer to Protection Modes for details.• No Light - Standby Mode or OFF.

LED FlashlightPress the LED Button once to cycle through four modes: LOW, HIGH, SOS, OFF.

PRESS AND HOLD to turn the hazard light ON/OFF.

!

READY TO JUMP

DISCONNECT!

RECHARGE ECOJUMP

STATUS

JUMP START INSTRUCTIONS:1. RED Clamp to (+) Terminal2. BLACK Clamp to (-) Terminal3. Insert Jump Start Cable4. Press Power Button5. Check Status Lights

POWER

PRESS: FLASHLIGHT

HOLD: HAZARD OVERRIDE

OverrideIndicator

Power Indicator

Hazard Light

Status Lights

Battery Level Indicator

NOTE: Unit must be ON for lights to function.

OverrideUse this function with EXTREME caution. Refer to Low-Voltage Vehicle Batteries & Manual Override for details.

Override Indicator:• Rapid RED Flashing - Override Mode.• No Light - Normal Operating Mode.

Status LightsREADY TO JUMP: • Solid GREEN Light - EcoJump is ready to jump start your battery.• Flashing GREEN Light - Wait until GREEN Light turns solid before jump starting your battery. Refer to Protection Modes for details.

DISCONNECT!:Something is connected incorrectly - Disconnect the clamps immediately!• Flashing RED Light - EcoJump is likely shorted. You must ensure clamps are not touching each other.• Solid RED Light - EcoJump is likely connected with reverse polarity. You must verify that the RED

Jump Start Cables

Plug

Clamps

08 09

Jump Starting Your VehicleCAUTION: Do NOT attempt to jump start if unit and/or connections are wet or damp.

To access the jump start connection on the side of your EcoJump, pull tab on the rubber cap that reads, "ENGINE START." Once the rubber cap is removed, the jump start connection will be exposed.

Carefully read and understand the vehicle owner’s manual on specific precautions and recommended methods for jump starting the vehicle. Make sure to determine the voltage and chemistry of the battery by referring to your battery owner’s manual prior to using this product. The EcoJump is for jump starting standard vehicle 12V lead-acid batteries only.

Connecting to the BatteryPrior to connecting to your battery, verify that it is a 12V lead-acid battery. The EcoJump is not suitable for

any other type of battery. Identify the correct polarity of the battery terminals on the battery. The positive and negative battery terminals are typically marked by the following letters or symbols, respectively: (POS, P, +), (NEG, N, -). Do NOT make any connections to the carburetor, fuel lines, or thin, sheet metal parts. The instructions below are for a negative ground system. If your vehicle is a positive ground system (very uncommon), follow Steps 1 and 2 in reverse order.

Connect the positive, RED, clamp to the positive (POS, P, +) battery terminal.

Connect the negative, BLACK, clamp to the negative (NEG, N, -) battery terminal or vehicle chassis.

PUSH TO SEAL

About EcoJumpThe EcoJump is a portable & waterproof lithium jump starter for vehicles with 12V lead-acid batteries (cars, trucks, boats, ATVs, motorcycles, etc.). It is designed for easy & safe use, with built-in reverse polarity & short circuit protection. The EcoJump has clearly labeled & easy to understand buttons, indicator lights, and connection ports. The EcoJump also provides live updates to your phone, via Bluetooth Low Energy, on the charge & temperature status of your EcoJump, ensuring the unit is ready for use when needed most! The EcoJump can be used up to 20 times on a single charge to jump start most 12V battery vehicles. It also has the convenience of two 5V USB ports for charging your smartphone and other devices, a 200 Lumen flashlight, and an emergency warning light.

NOTE: The EcoJump comes partially charged out of the box but needs to be fully charged prior to use.

1

2

& BLACK clamps are connected to the positive & negative battery terminals, respectively.

RECHARGE ECOJUMP:Solid YELLOW Light - Your EcoJump battery level is too low to use the jump start function. You must recharge before attempting to use as a jump starter.

NOTE: The EcoJump can connect to your smartphone using BLE (Bluetooth Low Energy) to inform you when your battery is running low.

Battery Level IndicatorEach BLUE LED bar represents 20% of a charge. Five full LEDs indicate a full charge. When the EcoJump battery level is below 15%, the first LED bar will flash slowly.

10 11

The EcoJump is designed to jump start 12V lead-acid batteries with voltage readings down to 3.2V. If your vehicle battery is below 3.2V, the READY TO JUMP LED will be OFF (even after connecting correctly to the POS and NEG battery terminals). This is an indication that the EcoJump cannot detect a battery.

If you need to jump start a battery below 3.2V, there is a Manual Override feature, which allows you to force ON the jump start function.

CAUTION: Use this mode with EXTREME CARE. This mode is for 12V lead-acid batteries only.

Both the spark proof and reverse polarity protection features are disabled in Override Mode.

Pay very close attention to the polarity of the battery before using this mode. Do NOT allow the positive and negative jump start clamps to touch or connect to each other as the product will generate sparks. This mode uses very high current (up to 500 Amps) that can cause sparks and high heat if not used properly. If you are unsure about using this mode, do NOT attempt and seek professional help.

Low-Voltage Vehicle Batteries & Manual Override - Use With Caution

period. Allow the EcoJump to rest for ten minutes before attempting to jump start the vehicle again.

Once you have started your vehicle, press the Power Button on the EcoJump to put it in Standby Mode, unplug the Jump Start Cables

7

NOTE: When disconnecting, disconnect in the reverse sequence, removing the negative clamp first.

Jump Start Connect the Jump Start Cables to the EcoJump.

Press the Power Button to turn ON EcoJump unit, when in Standby Mode (if the EcoJump is OFF, PRESS AND HOLD the Power Button to turn ON). The Battery Level Indicator lights and Power Indicator light will illuminate to show the unit is on and ready for use. If you are connected to a 12V battery, one of the Status Lights will also illuminate:

• READY TO JUMP: GREEN light ON means EcoJump is ready to jump start your battery.

• DISCONNECT!: Something is connected incorrectly - Disconnect the clamps immediately! RED light flashing means EcoJump is likely short circuited. RED light ON means EcoJump

is likely connected with reverse polarity.

• RECHARGE ECOJUMP: YELLOW light ON means your EcoJump battery level is too low to use the jump start function. You must recharge before attempting to use as a jump starter.

If the (GREEN) READY TO JUMP LED is lit, you are ready to proceed.

Make sure all of the vehicle’s power loads (headlights, radio, air conditioning, etc.) are turned off before attempting to jump start the vehicle.

Try starting the vehicle. Most vehicles will start immediately; however, some vehicles may require the EcoJump to be connected for up to 30 seconds before starting. If the vehicle does not start right away, wait 20-30 seconds before trying again. Do NOT attempt more than three consecutive jump starts within a ten-minute

3

4

from the EcoJump unit, and disconnect the jump start clamps from your vehicle (removing the negative, BLACK, clamp first). Remove the EcoJump from the vehicle engine compartment and store in a safe place in your vehicle, home, or office.

6

5

12 13

Before using the Manual Override feature, make sure the Jump Start Cable plug is connected to the EcoJump and the jump start clamps are connected to the correct polarity battery terminals. To use the Manual Override feature, PRESS AND HOLD the Override Button . The READY TO JUMP LED and Override Indicator LED will flash, indicating you have successfully entered into Manual Override Mode and it is ready to jump start your vehicle.

Most vehicles will start immediately; however, some vehicles may require the EcoJump to be connected for up to 30 seconds before starting. If the vehicle does not start right away, wait 20-30 seconds before trying again. Do NOT attempt more than three consecutive jump starts within a ten-minute period. Allow the EcoJump to rest for ten minutes before attempting to jump start the vehicle again.

Press the Power Button to exit Override Mode and enter Standby Mode.

CAUTION: Place your EcoJump in Standby Mode before disconnecting the jump start clamps. This will ensure your safety. Remember, both the spark proof and reverse polarity protection features are disabled in Override Mode.

CAUTION: Do NOT attempt to jump start if unit and/or connections are wet or damp.

Important: Maintaining WaterproofnessIf the caps are not properly closed, your EcoJump is NOT watertight. To ensure the unit is watertight & waterproof, ALWAYS CLOSE THE CAPS PROPERLY.

In order to ensure the unit is watertight, close rubber caps & PUSH along the EDGE of the RUBBER so that the caps are flush with the surface of the unit.

USB Charging Connections

To access the charge connections on the EcoJump, pull tab on the rubber cap.

InputConnect the USB cable to the USB micro Input to charge your EcoJump.

RECOMMENDATION: Use the USB cable and power adapter included in the box.

NOTE: Charge time from low to full charge is approx. 7 hrs.

CAUTION: Do NOT charge if unit and/or connections are wet or damp.

OutputConnect to one of the USB Output (5V, 2.1A & 5V, 2.1A) ports to charge your personal device. Use the USB cable included with your personal device.

NOTE: Charging rates are similar to the charging rate when connected to the USB of a desktop PC.

Charge time is approx. 1.5 hrs. from low to full for most smartphones; however, charge times will vary depending on the device being charged, the device’s battery specifications, and the device features. In some instances, your personal device may not indicate if a charge is in process.

CAUTION: Do NOT charge if unit and/or connections are wet or damp.

OUTPUTSINPUT

14 15

BLE and Smartphone App

Protection Modes

Bluetooth Low EnergyWhile your EcoJump is ON or in Standby Mode, it will

communicate its battery level and temperature via Bluetooth Low Energy (BLE)

EnvironmentalAs an added safety precaution, in situations where the EcoJump battery is exposed to extreme temperatures (above 122°F or below 0°F), the EcoJump will turn off all charge out and charge in functions until the battery returns to a temperature within its safe operating range. The EcoJump Power Indicator will flash BLUE when in this Protection Mode.

Extensive UseIf the EcoJump has been used extensively for multiple jump start attempts (10+) within a short period of time, the unit may start to get hot. If the EcoJump ever exceeds a safe operating temperature range, built-in safety protection circuitry will automatically turn the jump start function off, the READY TO JUMP LED will flash GREEN, and the jump start connection port

will become inactive. After a period of time has passed to allow the EcoJump to cool down, the READY TO JUMP LED will return to solid GREEN and the jump start connection will automatically re-activate.

Over CurrentIf the EcoJump has been used on a very heavy load (high current) application, the EcoJump may enter this Protection Mode to prevent damage to the EcoJump unit. If the EcoJump enters this Protection Mode, the built-in safety circuitry will automatically turn off the jump start function, the READY TO JUMP LED will flash GREEN, and the jump start connection port will become inactive. After approximately 10 seconds have passed, the READY TO JUMP LED will return to solid GREEN and the jump start connection will automatically re-activate.

to nearby smartphones. Download the EcoJump App to your smartphone. The App is available on the Apple App Store and the Google Play Store.

NOTE: The Bluetooth battery notifications do NOT work when EcoJump is OFF.

EcoJump AppThe EcoJump is App connected and provides live updates on the EcoJump battery charge level and temperature to your smartphone. The EcoJump uses Bluetooth Low Energy to send data to the EcoJump App on your smartphone whenever your smartphone is within range - typically about 30-60ft. You can configure the App to display pop-up warnings on your smartphone whenever the battery charge level has dropped below a given level or if the EcoJump unit is outside the recommended storage temperature range. These warnings sent to your smartphone help to ensure the EcoJump will be fully charged and ready for use when needed most.

NOTE: On iOS devices, the EcoJump App must be running in the background for the pop-up warnings to display on your smartphone.

When the unit is in Standby Mode, the battery will stay over 50% charged for up to 6 months. To optimize charge level while in storage, PRESS AND HOLD the Power Button for approximately 4 seconds to power OFF. In OFF mode, the EcoJump will stay over 50% charged for up to one year in a cool storage location, but your smartphone will NOT receive BLE battery notifications.

Temperature and other environmental conditions affect how long the EcoJump will stay charged while in storage. If you choose to not use the EcoJump App to receive BLE battery notifications, we recommend that you check your EcoJump charge status every 3 months and re-charge it as needed.

16 17

Unit Weight27.3 ouncesJump Start Output Power500A PeakPower Source11.1V, 5000mAh, 55.5WhLithium BatteryUSB Input5V, 2AUSB Output5V, 2.1A / 5V, 2.1ABluetooth Low Energy (BLE)Communicates the battery level and temperature to your smartphoneLED Flashlight200 Lumens

Unit Dimensions

8"

4.1"

1.8"

Specifications

Mount Attachment Point¼" diameterCharging OptionsUSB to 5V AC adapter or ComputerCharging TimeApproximately 7 hoursRecommended Max Storage(Battery) Temperature77°F / 25°C Recommended Min Storage(Battery) Temperature-4°F / -20°C Operating Temperature32°F to 113°F / 0°C to 45°C Waterproof/Dustproof RatingIP67

!

JUMP START INSTRUCTIONS:1. RED Clamp to (+) Terminal2. BLACK Clamp to (-) Terminal3. Insert Jump Start Cable4. Press Power Button5. Check Status Lights

READY TO JUMP

DISCONNECT!

RECHARGE ECOJUMP

STATUS

POWER

PRESS: FLASHLIGHT

HOLD: HAZARD OVERRIDE

PU

SH

TO

SE

AL

Mount Attachment Point Flashlight

For Charging (Sold Separately)USB Car Power Adapter (2A)

User Guide

Optional Accessories

What’s in the Box

EcoJump

Models: GDI-EXJMP1500...1520

User Guide

EcoJump

USB Cable

Carry Bag

AC Power Adapter

Jump Start Cables

18

LIMITED MANUFACTURER’S WARRANTY:The EcoJump is covered by a 3 year limited warranty that covers defects in workmanship and / or materials for a period of 3 years from original purchase date. This warranty does not apply to any products which have been abused, neglected, modified or used for a purpose other than the one for which they were manufactured. Please refer to the above care and maintenance instructions for suggested care details. The warranty is valid only for the original owner who purchases the unit from an authorized dealer. Transfers do not qualify for warranty protection. Grace Digital reserves the right to replace any out-of-stock or discontinued product with a comparable product. Discontinued products may not be available for warranty replacement. Any contents are NOT covered by the limited manufacturer’s warranty. Warranty terms may be revised without notification at the discretion of the manufacturer. Please visit www.ecoxgear.com for additional product & warranty information.

EcoJump by ECOXGEAR, a division of Grace Digital Inc., San Diego, California. Designed and Engineered in the USA. Made in China.

Patent Pending.

Ambient Storage Temperature Range-4°F to 77°F

Jump Start Output PowerPeak Current12Vdc, 500A (continuous 0.1S, interrupted 15S)

Start Current12Vdc, 200A (continuous 3S, interrupted 15S)