View
216
Download
3
Tags:
Embed Size (px)
Citation preview
EBB 220/3POLYMER ADDITIVES
DR AZURA A.RASHIDRoom 2.19
School of Materials And Mineral Resources Engineering,
Universiti Sains Malaysia, 14300 Nibong Tebal, P. Pinang Malaysia
Most of polymers need to add with specific ingredients to obtain desirable properties.
Additives were used: To improved or modify the mechanical, chemical, and physical
properties To prevent degradation (both during fabrication and in service) To reduce materials costs To improve the processability
Each of the additives in formulation has specific functions either during processing or end products applications
Typical additives include filler materials, Plasticizer stabilizers, colorants flame retardants.
IntroductionIntroduction
Fillers normally add in polymeric materials for economical or technical
Filler materials are most often added to polymers to improve tensile and compression strengths, abrasion resistance, toughness, dimensional and thermal stability and other properties.
Materials used as particulate fillers include wood flour (finely powdered sawdust), silica flour and sand, glass, clay, talc, limestone, and even some synthetic polymers.
Particle sizes range all the way from 10 nm to macroscopic dimensions
Because these inexpensive materials replace some volume of the more expensive polymer, the cost of the final product is reduced.
FillersFillers
Can be in liquid, half solid or solid form.
It must be compatible with the polymeric materials and other compounding ingredients incompatibility will results in poor processing properties.
Plasticizer were used for:
1. ‘extender’ (large amount >20 pphr) to make the end products cheaper
2. Processing aid (small amount 2-5 pphr) to make the processing easier
3. Modifier to modifies some polymeric properties.
PlasticizersPlasticizers
The aid of additives called plasticizers can :
improved the flexibility, ductility, and toughness
produces reductions in hardness and stiffness
lowers the glass transition temperature at ambient conditions the polymers may be used in applications requiring some degree of flexibility and ductility.
These applications include thin sheets or films, tubing, raincoats, and curtains.
Some polymeric materials under normal environmental conditions are subject rapid deterioration in mechanical properties.
Most often this deterioration is a result of exposure to light in particular ultraviolet radiation and oxidation
Ultraviolet radiation causes a severance of some of the covalent bonds along the
molecular chain also result in some crosslinking.
Oxidation deterioration is a consequence of the chemical interaction between oxygen atoms and the polymer molecules.
Additives that counteract these deteriorative processes are called stabilizers.
StabilizersStabilizers
Colorants impart a specific color to a polymer
They may be added in the form of:
dyes The molecules in a dye actually dissolve and become part
of the molecular structure of the polymer.
pigments. Pigments are filler materials that do not dissolve but
remain as a separate phase;
have a small particle size, are transparent, and have a refractive index near to that of the parent polymer.
Others may impart opacity as well as color to the polymer.
ColorantsColorants
The flammability of polymeric materials is a major concern, especially in the manufacture of textiles and children's toys.
Most polymers are flammable in their pure form exceptions include those containing significant contents of chlorine and/or fluorine such as polyvinyl chloride (PVC) and polytetrafluoroethylene (PTFE).
The flammability resistance of the remaining combustible polymers enhanced by additives called flame retardants.
These retardants may function by
interfering with the combustion process through the gas phase, or
by initiating a chemical reaction that causes a cooling of the combustion region and a termination of burning.
Flame retardantsFlame retardants
Special purpose additivesSpecial purpose additives
Additives Function
Blowing agents Gas generating chemicals that are necessary for manufacturing sponge or micro porous products
Odorants Strongly scented substances added in small amounts that are capable of imparting a pleasant scent
Antistatic agents Added to reduce the accumulated of dust or dirt on surface and also to minimize possibility of sparking resulting from the discharge of accumulated static electricity
Retarders Substances that used to reduce the tendency of rubber mix to scorch avoid premature vulcanization during processing
Antioxidants Protects products from oxidation of heat
Antiflex cracking Agents that retard cracking caused by cyclic deformations
What is the function of additives in polymeric materials?
Discuss the used of fillers as one of polymer compounding ingredients.
Example of the exams questionExample of the exams question
EBB 220/3MISCELLANEOUS
APPLICATIONS
DR AZURA A.RASHIDRoom 2.19
School of Materials And Mineral Resources Engineering,
Universiti Sains Malaysia, 14300 Nibong Tebal, P. Pinang Malaysia
Coating are frequently applied to the surface of materials to serve one or more of the following function:
1. to protect the item from the environment that may produce corrosive or deteriorative reactions;
2. to improve the item's appearance
3. to provide electrical insulation.
CoatingCoating
Many of the ingredients in coating materials are polymers with majority are organic in origin
These organic coatings fall into several different classifications:
paint, varnish, enamel, lacquer, and shellac :
An adhesive substance used to join together the surfaces of two solid material (termed "adherends") to produce a joint with a high shear strength
Adhesives may come from either natural or synthetic sources.
Some modern adhesives are extremely strong, and becoming increasingly important in modern construction and industry
The bond forces between the adhesive and adherend surfaces are electrostatic similar to the secondary bonding forces between the molecular chains in thermoplastic polymers
A strong joint may be produced if the adhesive layer is thin and continuous.
If a good joint is formed, the adherend material may fracture or rupture before the adhesive.
AdhesivesAdhesives
Polymeric materials that fall within the classifications of thermoplastics, them setting resins, elastomeric compounds, and natural adhesives (animal glue, cast starch, and resin) may serve adhesive functions.
Polymer adhesives may be used to join a large variety of material combinations: metal-metal, metal-plastic, metal-ceramic, and so on.
The primary drawback is the service temperature limitation.
Organic polymers maintain their mechanical integrity only at relatively low temperatures, and strength decreases rapidly with increasing temperature.
Natural adhesives Adhesives based on vegetable (natural resin), food (animal hide and
skin), and mineral sources (inorganic materials).
Synthetic adhesives Adhesives based on elastomers, thermoplastic, and thermosetting
adhesives.
Drying adhesives These adhesives are a mixture of ingredients polymer dissolved in a
solvent e.g. glues and rubber cements As the solvent evaporates the adhesive hardens and they will adhere
to different materials to greater or lesser degrees. These adhesives are typically weak and are used for household
applications. Some intended for small children are now made non-toxic.
Hot adhesives (thermoplastic adhesives) Also known as "hot melt" adhesives they are applied hot and simply allowed to harden as they cool. These adhesives have become popular for crafts because of their ease
of use and the wide range of common materials to which they can adhere.
Some categories of adhesivesSome categories of adhesives
Adhesives may fail in one of two ways:
1. Adhesive failure is the failure of the adhesive to stick or bond with the material to be adhered (also known as the substrate or adherend).
2. Cohesive failure is structural failure of the adhesive. Adhesive remains on both substrate surfaces, but the two items separate.
Two substrates can also separate through structural failure of one of the substrates
this is not a failure of the adhesive. In this case the adhesive remains intact and is still bonded to one substrate and the remnants of the other.
For example, when one removes a price label, adhesive usually remains on the label
and the surface this is cohesive failure. If, however, a layer of paper remains stuck to the surface the
adhesive has not failed.
when someone tries to pull apart oreo cookies with the filling all on one side. The goal is an adhesive failure, rather than a cohesive failure.
Adhesives failureAdhesives failure
Polymeric materials have found widespread use the form of thin films.
Films having thicknesses between 0.001-0.0005 in (0.025 -0.125 mm)
Used extensively as bags for packaging food products and other merchandise, as textile products, and a host of other uses.
Important characteristics of the materials produced and used as films include:
Low density, high degree of flexibility, high tensile and tear strengths, resistance attack by moisture and other chemicals, low permeability to some gases, especially water vapor.
FilmsFilms
Some of the polymers that meet these criteria and are manufactured in film form are:
polyethylene, polypropylene, cellophane, and cellulose etate.
There are several forming methods:
simply extruded through a thin die slit followed by a rolling operation that serves to reduce thickness and improve strength.
Blown moulding continuous tubing is extruded through an annular die; and
maintaining a controlled positive gas pressure inside the tube,
wall thickness may be continuously reduced( to produce a thin cylindrical film, which may be cut and laid flat.
Some of the newer films produce using co extrusion that is, multi layers of more than one polymer type are extruded simultaneously.
Very porous plastic materials produced in a process called foaming
Both thermoplastic and thermosetting materials may be foamed by including in the batch a blowing agent upon heating decomposes with the liberation of a
gas.
gas bubbles are generated throughout the now-fluid mass remain as pores up cooling and give rise to a sponge-like structure.
The same effect is produced bubbling an inert gas through a material while it is in a molten state.
FoamsFoams
Some of commonly foamed polymers are :
polyurethane, rubber, polystyrene, and polyvinyl chloride.
Foams are commonly used as:
cushions in automobiles and furniture in packaging and thermal insulation.
Discuss two of the various applications of polymeric materials.
What are the polymer characteristic to produced a film?
Example of the exams questionExample of the exams question