T h e M a r c o P i p e F l a s h i n g S y s t e m

• Easy, on-site customization

• Maximum resistance to ozone/ultraviolet weathering

• Flexible base forms seal with most panels

• EPDM or Silicone sleeve accommodates expansion/contraction

• Many sizes and color choices

RoofBootsRoofBoots™ are made with clearly marked sleeves which can be cut on-site

to easily customize and precisely fit the pipe diameter you need. The sleeves

come in EPDM 500 and Silicone—designed for the maximum resistance to

weathering due to ozone and ultraviolet light.

The base on RoofBoots is flexible and designed

to form a seal on all types of roofing surfaces

(including metal, plastic, tile, and more), and

on almost any panel configuration and roof pitch, regardless of the pipe

location.

So installation is simple: choose the pipe opening and trim the sleeve, slide

the boot over the pipe, form to the roof profile, apply sealant, and fasten to

complete the installation.

You can also choose from round or square base, from Marco’s full selection of

wraparound retrofit and solar boots, many sizes, and several color choices.

Made with Recycled Material

NEW HIGH TEMP ROOFBOOTS

N O W A V A I L A B L E I N G R A Y

pipe f

lashin

g

1 0 C O L O R S*

Black Brown Gray White Dark Green Dark BlueLight Green Light Blue Bright Red Terra Cotta

As part of a standard classification system for rubber products these general specifications present conservation engineering minimums which should be used for design criteria. General recommendations must be tested for extreme applications.

*Special order colors are sold in box quantity.

ASTM D2000 M3 BA 510 A14 B13 C12 F17 Z1 Z2 Z3 Z4 Z5 Z6 Z7

GRADE 3

TYPE B ........................ General Tes Temp 100°C

CLASS A ..................... Volume Swell no req

5 ................................. 50 Durometer (range)

10 ............................... Tensile 10 MPa (approx. 1450 psi)

A14 ............................. Heat Aging 70 hrs @ 100°C

B13 ............................. Compression Set 22 hrs @ 70°C

.................................... Max 25% ASTM D395B

C12 ............................. Ozone Resistance

.................................... 70 hrs @ 50pphm ASTM D1171

.................................... 100% Quality Retention

F17 .............................. Low Temperature Brittleness

.................................... 3 min @ -40°C Pass ASTM D2137 A, 9, 3, 2

Z1 ............................... 55 Durometer (specific target)

Z2 ............................... EPDM (specific elastomer)

Z3 ............................... Horizontal Flame Resistance, UL 94

.................................... Not to exceed 3"/min

Z4 ................................ Ozone Resistance Advanced Requirement

Z5 ............................... 70 hrs @ 500pphm @ 100°F

.................................... Accelerated Weathering Resistance

Z6 ............................... (U.V. Light), ASTM G-53

Z7 ............................... Tear Resistance, ASTM D-624, die “D”

.................................... Resistance to Discoloration, ASTM

ASTM D2000 M4 GE 505 A19 B37 C12 F19 G11 Z1 Z2 Z3 Z4

GRADE 4

TYPE G........................ General Tes Temp 225°C

CLASS E ...................... Volume Swell Max 80%

5 ................................. 50 Durometer (range)

05 ............................... Tensile 5 MPa (minimum 725 psi)

A19 ............................. Heat Aging 70 hrs @ 225°C

.................................... Change in Hardness max +10 pts

.................................... Change in Tensile max -30%

.................................... Change in Ultimate Elongation max -30%

B37 ............................. Compression Set 22 hrs @ 175°C

.................................... Max 50% ASTM D395B

C12 ............................. Ozone Resistance

.................................... 70 hrs @ 50pphm ASTM D1171

F19 .............................. Low Temperature Brittleness

.................................... 3 min @ -55°C pass ASTM D2137 A, 9, 3, 2

G11 ............................. Tear Resistance, ASTM D-624, die “B”

Z1 ............................... 55 Durometer (specific target)

Z2 ............................... Silicone (specific elastomer)

Z3 ............................... Horizontal Flame Resistance, UL 94

.................................... not to exceed 3"/min

Z4 ................................ Ozone Resistance Advanced Requirement

.................................... 70 hrs @ 500pphm @ 100°F

EPDM

SILI

CON

E

PIPERANGE COMPOUND FLASHINGDETAILS

#1 1/4"–2 1/2" Black EPDM Red Silicone A Top opening diameter Closed (6–63.5 mm) Gray EPDM Gray Silicone B overall height 2.77" (70.4 mm) C Base diameter 4.75" (120.7 mm)

#2 1 3/4"–3 1/4" Black EPDM Red Silicone A Top opening diameter 1.44" (36.6 mm) (45–83 mm) Gray EPDM Gray Silicone B Overall height 3.35" (89.7 mm) C Base diameter 6.21" (157.7 mm)

#3 1/4"–5" Black EPDM Red Silicone A Top opening diameter Closed (6–127 mm) Gray EPDM Gray Silicone B Overall height 3.64" (92.5 mm) C Base diameter 7.74" (196.6 mm)

#4 3"–6 1/4" Black EPDM Red Silicone A Top opening diameter 2.38" (60.5 mm) (76–158.8 mm) Gray EPDM Gray Silicone B Overall height 5.05" (128.3 mm) C Base diameter 9.26" (235.2 mm)

#5 4 1/4"–7 1/2" Black EPDM Red Silicone A Top opening diameter 3.50" (88.9 mm) (108–191 mm) Gray EPDM Gray Silicone B Overall height 4.43" (112.5 mm) C Base diameter 10.75" (273 mm)

#6 5"–9" Black EPDM Red Silicone A Top opening diameter 4.25" (108 mm) (127–228.6 mm) Gray EPDM Gray Silicone B Overall height 5.60" (142.2 mm) C Base diameter 12.50" (317.5 mm)

#7 6"–11" Black EPDM Red Silicone A Top opening diameter 4.90" (124.5 mm) (152–279 mm) Gray EPDM Gray Silicone B Overall height 5.84" (148.3 mm) C Base diameter 14.60" (370.8 mm)

#8 7"–13" Black EPDM Red Silicone A Top opening diameter 5.80" (147.3 mm) (178–330 mm) Gray EPDM Gray Silicone B Overall height 7.53" (191.3 mm) C Base diameter 16.5" (419.1 mm)

#9 10"–19" Black EPDM Red Silicone A Top opening diameter 7.45" (189.2 mm) (254–483 mm) Gray EPDM Gray Silicone B Overall height 8.09" (205.5 mm) C Base diameter 25.25" (641.4 mm)

SIZING CHARTCheck diameter of pipe. Select the appropriate RoofBoots™ product for pipe or duct diameter. For extreme pitch or surface irregularity select next larger size. Choose the compound required, then refer to the part number for the RoofBoots™ product desired.

PIPERANGE COMPOUND FLASHINGDETAILS

Min. 0–1 1/2" Black EPDM A Top opening diameter 1/16" (0–38 mm) Gray EPDM B Cut to suit pipe size 1/8"–3/4" C Base diameter 2 1/4"

#1 1/4"–2 1/2" Black EPDM A Top opening diameter Closed (6–63.5 mm) Gray EPDM B Cut to suit pipe size 1/4"–2" Red Silicone C Base diameter 4 1/4"

#2 1/4"–3" Black EPDM A Top opening diameter 7/8" (6–76 mm) Gray EPDM B Cut to suit pipe size 1 1/4"–3" Red Silicone C Base diameter 6"

#3 1/4"–5" Black EPDM A Top opening diameter Closed (6–127 mm) Gray EPDM B Cut to suit pipe size 1/4–4" Red Silicone C Base diameter 8"

#4 3"–7" Black EPDM A Top opening diameter 2 1/2" (76–178 mm) Gray EPDM B Cut to suit pipe size 3"–6" Red Silicone C Base diameter 10"

#5 4"–8" Black EPDM A Top opening diameter 3 1/2" (102–203 mm) Gray EPDM B Cut to suit pipe size 4"–7" Red Silicone C Base diameter 11"

#6 5"–9" Black EPDM A Top opening diameter 4" (127–228.6 mm) Gray EPDM B Cut to suit pipe size 5"–9" Red Silicone C Base diameter 12"

#7 6"–12" Black EPDM A Top opening diameter 5" (152–305 mm) Gray EPDM B Cut to suit pipe size 6"–11" Red Silicone C Base diameter 14"

#8 6 3/4"–14" Black EPDM A Top opening diameter 6" (171–356 mm) Gray EPDM B Cut to suit pipe size 7"–13" Red Silicone C Base diameter 17"

#9 9"–20" Black EPDM A Top opening diameter 8 1/2" (228.6–508 mm) Gray EPDM B Cut to suit pipe size 10"–18" Red Silicone C Base diameter 25"

#10 15 3/4"–29 1/2" Black EPDM A Top opening diameter 11" (400–749 mm) Red Silicone B Cut to suit pipe size 13"–26" C Base diameter 34"

PIPERANGE COMPOUND FLASHINGDETAILS3/4"–1" Black EPDM A Top opening diameter 3/4" – 1" (19 – 25mm)3/4"–1" Red Silicone B Overall height 2 1/2" (63.5mm) C Base diameter 4" (101mm)

SOLAR – STANDARD / MULTIPORT• Maximum resistance to weathering• Conformance to stringent ozone and UV light• Multiport is specifically designed for solar and electrical applications • 5 Port Design – one design, multiple functions

Multiport Accommodates:One 0" – 1-15/16" - (0 - 49mm) PipeTwo 3/8" (0.9525mm) pipe / cableTwo 3/4" (20mm) pipe / cable

4-1/2" (114mm) BaseUp to 4 cables or wires per flashingExtra ports accommodate copper pipe/electrical cablingEasy install for solar applications

PIPERANGE COMPOUND FLASHINGDETAILS0"–1 5/16" Black EPDM A Top opening diameter 0" – 1 5/16" (0 – 49mm) Red Silicone B Overall height 2 1/2" (63.5mm) C Base diameter 4 1/2" (114mm)

STEEP SLOPE

PIPERANGE COMPOUND FLASHINGDETAILS1/4" — 5 3/4" Black EPDM A Top opening diameter Closed Red Silicone B Cut to suit pipe size 1/4" - 5 3/4" (6 - 146mm) C Base diameter 11" (279mm)

• Designed for 35° to 65° metal roof angles• Plumbing and Type B vents• Self extinguishing rubber compound

MADE IN USA1.800.800.8590 M a r c o I n d u s t r i e s . c o m

With Marco’s Rapid Response™ get more of what you need faster and easier. Take advantage of free shipping with low minimum orders. Marco - we’re big on customer service and small on hassle. Build it smart. Buy it smarter.

RoofBoots™ represent yet another Marco Industries development in bringing you innovative, higher quality, and more economical products for the building industry.

FOAM CLOSURE

SEALANTS

VENTILATION

FLASHING

DOORS

FASTENERS

UNDERLAYMENT

SystemAdvantage

Marco Weather-Tite®

S P E C S & E A S Y I N S T A L L

041-2

EPDM 500 SILICONEADVANCED OZONE RESISTANCE tested 70 hours @ 500 pphm 70 hours @ 500 pphm HIGH TEMPERATURE RESISTANCETested to: intermittent +100°C (+212°F) +135°C (+275°F)Tested to: continuous +225°C (+437°F) +260°C (+500°F) Solar: Tested to: intermittent +135°C (+275°F) +260°C (+500°F) Solar: Tested to: continuous +100°C (+212°F) +225°C (+437°F) LOW TEMPERATURE RESISTANCE tested -55°C (-65°F) -74°C (-101.2°F)Solar Low Temp -50°C (-67°F) -74°C (-101.2°F)

TENSILE SET maximum 10 MPa (1450 psi) 5 MP1 (700 psi)COMPRESSION SET maximum 25% 50%

Complete specification data and testing methods are available upon request.

You will need these products also:

QUIKDRILLMetal to metal fastener

QUIKGRIPMetal to wood fastener

TITEBONDMetal roof sealant

See our installation animations online at MarcoIndustries.com

WARRANTY

Choose the pipe opening and trim the sleeve

Apply sealant Fasten to roof