Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
e 908Instruction manual
e908_Manual_01_2019_EN.indd 1 26.02.2019 13:58:51
e 908 | 2/8
Delivery includes
Delivery includese 908 D e 908 B e 908 B ew
• e 908 D microphone • e 908 B microphone • e 908 B ew microphone
• MZA 900 P phantom power adapter
• MZA 900 P phantom power adapter
• MZH 908 D microphone clamp
• MZH 908 B microphone clamp
• MZH 908 B microphone clamp
• Pouch • Pouch • Pouch
• Quick guide • Quick guide • Quick guide
• Safety guide • Safety guide • Safety guide
Product overview
2
1
3
5
1
23
44
e 908 D e 908 B / e 908 B ew
1. Microphone head2. MZH 908 D microphone clamp3. Gooseneck4. XLR-3 connector5. Knurled screw
1. Microphone head2. MZH 908 B microphone clamp3. Gooseneck4. e 908 B: XLR-3 connector
e 908 B ew: 3.5 mm jack
e908_Manual_01_2019_EN.indd 2 26.02.2019 13:58:52
e 908 | 3/8
Installation
Installation
Attaching the microphoneCarefully bend the flexible goose neck.
Connecting the microphonePlug the 3.5 mm mini jack plug into the 3.5 mm jack socket of the MZA 900 P phantom power ad-apter (included with e 908 B and e 908 D).
Tighten the coupling ring.
Plug the XLR cable into the XLR output of the MZA 900 P phantom power adapter.
e908_Manual_01_2019_EN.indd 3 26.02.2019 13:58:52
e 908 | 4/8
Installation
Using the windshieldPlace the MZW 908 (optional accessories) windshield over the microphone head.
e908_Manual_01_2019_EN.indd 4 26.02.2019 13:58:53
e 908 | 5/8
Operation
Operation
Positioning the microphone e 908 B/e 908 B ew on a wind instrumentUse the microphone clamp to attach the e 908 to the bell of the instrument.
It is vital to observe the following notes:
Position Resulting sound Commentary
A Reduced ambient noise Directed into the bell of the instrument.
B Clear, powerful sound
C Balanced, natural sound Directed partly towards the bell and partly towards the body of the instrument.
A B C
Positioning the microphone e 908 D on a drumAttach the drum clamp to the rim of the drum by putting the upper part of the clip onto the rim and clipping it on by pushing down the drum clamp in a rotating action until it snaps into place.
Loosen the knurled screw.
Insert the gooseneck from the side into one of the two slots.
Tighten the knurled screw.
It is vital to observe the following notes:
Position Resulting sound Commentary
D More fundamentalLittle overtones
Position on the drum: 3–5 cm above the drumskin, directed towards the center of the drumskin, the fundamental to overtones ratio can be adjusted by changing the angle of the microphone. The most balanced results are obtained at an angle of 30–60°.
E Less fundamentalMany overtones
F Pronounced proximity effect Optional: tangential position of the gooseneck in order to reduce the distance to the drumskin.
D E F
You can attach two microphones to the drum clamp (e.g. for picking up two toms in cramped space conditions). To do so, use both slots of the drum clamp.
The various adjustment possibilities of the MZH 908 D and MZH 908 B clamps together with the flexible gooseneck enable the microphone to be optimally positioned on the sound source.
e908_Manual_01_2019_EN.indd 5 26.02.2019 13:58:53
e 908 | 6/8
Cleaning and maintaining the e 908
Positioning the monitor loudspeakersTo prevent feedback and crosstalk, postion your monitor loudspeakers in the angle area of the highest cancellation of the microphone (approx. 180°).
180°
Cleaning and maintaining the e 908
CAUTIONLIQUIDS CAN DAMAGE THE ELECTRONICS OF THE PRODUCT!
Liquids entering the housing of the product can cause a short-circuit and damage the electronics.
Keep all liquids away from the product.
Do not use any solvents or cleansing agents.
Disconnect the products from the power supply system and remove rechargeable batteries and batteries before you begin cleaning.
Clean all products only with a soft, dry cloth.
e908_Manual_01_2019_EN.indd 6 26.02.2019 13:58:54
e 908 | 7/8
Specifications
SpecificationsTransducer principle pre-polarised condenser microphone
Frequency response 40 - 20,000 Hz
Pick-up pattern cardioid
Sensitivity (free field, no load) 4.0 mV/Pa
Nominal impedance (at 1 kHz) 100 Ω (balanced)*
Min. terminating impedance 2 kΩ*
Max. sound pressure level (active) e 908 B, e 908 D e 908 B ew
35 dB(A)30 dB(A)
Phantom powering 12 - 48 V*
Connector e 908 B, e 908 D e 908 B ew
XLR-3*3.5 mm jack
Dimensions 47 x 193 mm
Weight 140 g
* with MZA 900 P (e 908 B/e 908 D); e 908 B ew for direct connection to ew transmitters
Polar pattern
125 Hz250 Hz500 Hz
1,000 Hz
2,000 Hz4,000 Hz8,000 Hz
16,000 Hz
30°0°
180°150°
120°
60°
90°
05
10152025dB
30°0°
180°150°
120°
60°
90°
Frequency response
-40
-50
-60
-70
-80
-9050
100
200500
1,000
2,0005,000
10,000
20,000Hz
dBV
0°, 1 m
e908_Manual_01_2019_EN.indd 7 26.02.2019 13:58:54
e 908 | 8/8
Overview of applications
Connector assignment
3
2 1+
+
e 908 B/e 908 D
e 908 B ew
3.5 mm3.5 mm
3.5 mm
Overview of applicationsPrimary application
Secondary application
• • • • • • •• • • • • •• • • • •
• • • • • •• • • • • • • •
• • •• • •• • •
• • •• • • • •
• • • • • •• • • • • •
• • • • • •• • • • • • • •
• •• •• • • • •
e 602 II
e 604
e 608
e 609 silver
e 614
e 835
e 845
e 865
e 901
e 902
e 904
e 906
e 908
e 914
e 935
e 945
e 965
e908_Manual_01_2019_EN.indd 8 26.02.2019 13:58:55