Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
FLASHERS
STANDARD FLASHERS This product range offers direct equivalents to most other manufacturers’ ranges. All units meet legislative requirements. A range of audible and visual devices is available to provide indication of operational status.
The units are supplied in Din style cases as a plug in unit (no mounting bracket), or with a vertical or horizontal mounting bracket. SPECIFICATION: DIN PACK DIN PACK WITH VERTICAL
BRACKET DIN PACK WITH
HORIZONTAL BRACKET VOLTAGE 12V AND 24V 12V AND 24V 12V AND 24V DIMENSIONS 74mm X 61mm X 36mm 94mm X 61mm X 36mm 74mm X 91mm X 45mm WEIGHT 55g 70g 80g FIXING PCB PLUG IN 1 POINT FIXING
5mm HOLE 2 POINT FIXING
6mm HOLES 73mm FIXING CENTRES
WHEN ORDERING, PLEASE STATE VOLTAGE REQUIRED
LAMP LOAD & SPEC: 2 + 1 X 21 WATT 6 X 21 WATT HAZARD 2 + 1 (2 W/L) 5 PIN
LAMP LOAD & SPEC: 2 + 1 X 21 WATT 6 X 21 WATT HAZARD 2 + 1 (2 W/L) 6 PIN
PART NO DESCRIPTION CASE E009
621-02-P5
DIN PACK
E007
621-02-P5VB
DIN PACK + VERTICAL BRACKET
E099
621-02-P5HB
DIN PACK + HORIZONTAL BRACKET
PART NO DESCRIPTION CASE E003
621-02-P6
DIN PACK
E008
621-02-P6VB
DIN PACK + VERTICAL BRACKET
E098
621-02-P6HB
DIN PACK + HORIZONTAL BRACKET
Page 3.1
FLASHERS
LAMP LOAD & SPEC: 3 + 1 X 21 WATT 8 X 21 WATT HAZARD 3 + 1 (2 W/L) 5 PIN
LAMP LOAD & SPEC: 3 + 1 X 21 WATT 8 X 21 WATT HAZARD 3 + 1 (2 W/L) 6 PIN
LAMP LOAD & SPEC: 4 + 1 X 21 WATT 10 X 21 WATT HAZARD 4 + 1 (2 W/L) 6 PIN
EURO MANUFACTURING AND MARKETING LIMITED
Euro Works, 11 – 13 High Street, Wem, Shropshire, SY4 5AA, England. Tel: +44 (0) 1939 235073 Fax: +44 (0) 1939 235074
Email: [email protected] Web Site: www.eurogroup.gb.com
Page 3.2
PART NO DESCRIPTION CASE E104
631-02-P5
DIN PACK
E105
631-02-P5VB
DIN PACK + VERTICAL BRACKET
E120
631-02-P5HB
DIN PACK + HORIZONTAL BRACKET
PART NO DESCRIPTION CASE E116
631-02-P6
DIN PACK
E123
631-02-P6VB
DIN PACK + VERTICAL BRACKET
E097
631-02-P6HB
DIN PACK + HORIZONTAL BRACKET
PART NO DESCRIPTION CASE E663
641-02-P6
DIN PACK
E189
641-02-P6VB
DIN PACK + VERTICAL BRACKET
E044
641-02-P6HB
DIN PACK + HORIZONTAL BRACKET
SPECIAL PURPOSE FLASHERS
PF1224-10 ELECTRONIC POWER FLASHER This Unit was designed to flash Headlights on Police Cars and Emergency Vehicles. It has many other uses but should not be used to drive Relays etc. LAMP LOAD & SPEC: 2 X 60 WATT @ 12VOLT 4 X 75 WATT @ 24VOLT 4 PIN
530-SS ELECTRONIC FLASHER This Unit was designed to operate 3 X 24V 21W Bulbs and a maximum of 6 in Hazard Mode. The Lamp overload feature reduces the flash-rate to 1 operation every 4 seconds if the total load exceeds 6.5 bulbs. The flash-rate increases in frequency if only 1 X 21W bulb is connected and the ‘S’ Terminal is unconnected. If 3 Lamps are connected and the ‘S’ Terminal is connected to zero volts (- 0V) the flash-rate will increase when only 2 bulbs remain connected. With the ‘S’ terminal unconnected, the ‘P’ Terminal will operate when 2 bulbs are connected. When the ‘S’ Terminal is connected to zero volts (- 0V), the ‘P’ Terminal operates when 3 lamps are connected. The Unit is available in a choice of 2 Case styles - 530-DIN and 530-SS
Page 3.3
PART NO DESCRIPTION CASE E637-E
PF1224-10 POWER FLASHER
DIN PACK + VERTICAL BRACKET
PART NO DESCRIPTION CASE E013-D
530-DIN
DIN PACK + VERTICAL BRACKET
E013
530-SS
ALUMINIUM CASE
WEIGHT: 230g DIMENSIONS: 72mm X 98mm X 31mm 2 POINT FIXING – 6 mm HOLES
77mm FIXING CENTRES
SPECIAL PURPOSE FLASHERS
401-01-P4 ELECTRONIC FLASHER LAMP LOAD & SPEC: 2 + 0 (1 W/L) 12V 4 PIN
621-01-SS ELECTRONIC FLASHER 2 + 1 (1W/L) This Unit was designed to operate 3 X 24V 21W Bulbs with a maximum of 6 in Hazard Mode
621-02-SS ELECTRONIC FLASHER 2 + 1 (2W/L) This Unit was designed to operate 3 X 24V 21W Bulbs with a maximum of 6 in Hazard Mode
Page 3.4
PART NO DESCRIPTION CASE E185
401-01-P4
DIN PACK + VERTICAL BRACKET
PART NO DESCRIPTION CASE E001
621-01-SS
ALUMINIUM CASE
WEIGHT: 230g DIMENSIONS: 72mm X 98mm X 31mm 2 POINT FIXING – 6 mm HOLES
77mm FIXING CENTRES
PART NO DESCRIPTION CASE E002
621-02-SS
ALUMINIUM CASE
WEIGHT: 230g DIMENSIONS: 72mm X 98mm X 31mm 2 POINT FIXING – 6 mm HOLES
77mm FIXING CENTRES
SPECIAL PURPOSE FLASHERS E716 12V TRACTOR FLASHER This Flasher has been designed to meet the latest Legislation and Regulations governing Tractors and other Agricultural Vehicles etc.
Specification:
Wiring Diagram
EURO MANUFACTURING AND MARKETING LIMITED Euro Works, 11 – 13 High Street, Wem, Shropshire, SY4 5AA, England.
Tel: +44 (0) 1939 235073 Fax: +44 (0) 1939 235074 Email: [email protected] Web Site: www.eurogroup.gb.com
Page 3.5
2+1+1x21W 5W 5W2.2W
2+1+1x21W
DIRECTION
C231
49C49A
C3
+12V
HAZARD
PART NO E716 VOLTAGE 12 VOLT CASE DIN PACK +
VERTICAL BRACKET
FLASH RATE PANEL LAMPS LOAD 70 95 150 C C2 C3 1 BULB X X 2 BULBS X X 3 BULBS X X X >3 BULBS X X X X
INTERRUPTERS
This range of Solid State Interrupters will cover most requirements and will interrupt power over a broad range from Pilot Lights to Multiple Flashers and Beacons. 1200 INTERRUPTER LAMP LOAD & SPEC: INTERRUPTER 6 X 21 WATT 4 PIN
1058 INTERRUPTER LAMP LOAD & SPEC: INTERRUPTER LOAD: 9WATT @ 24V MAX 4 WIRE
EURO MANUFACTURING AND MARKETING LIMITED
Euro Works, 11 – 13 High Street, Wem, Shropshire, SY4 5AA, England. Tel: +44 (0) 1939 235073 Fax: +44 (0) 1939 235074
Email: [email protected] Web Site: www.eurogroup.gb.com
Page 3.6
PART NO DESCRIPTION CASE E030-D
1200-DIN
DIN PACK + VERTICAL BRACKET
E030
1200
ALUMINIUM CASE
WEIGHT: 230g DIMENSIONS: 72mm X 98mm X 31mm 2 POINT FIXING – 6 mm HOLES
77mm FIXING CENTRES
PART NO DESCRIPTION CASE E014
1058
SMALL CASE WEIGHT: 51g
DIMENSIONS: 58mm X 35mm X 14mm 1 POINT FIXING – 6mm HOLE
INTERRUPTERS
E996 VARIABLE TIMED INTERRUPTER This unit was originally designed to flash a 3 LED Seat Belt warning sign for a period of time after the coach door is closed. The Timed Period can be set to any value between 5 seconds and about 3 minutes. A multi-turn preset is used to provide easy and accurate adjustment giving approximately 9 seconds per turn. It will work with voltages from 9V to 30V and is capable of interrupting the power to a 500mA maximum load.
Specification: Part Number E996 Description Variable Timed Interrupter Supply Voltage (Vin) 9V to 30V Supply Current V in = 28V, Output On With No Load V in = 28V, Output Off
8mA 3mA
Output Current V in = 9V to 30V
500mA maximum
Timed Period (Factory Setting) 30 seconds Timed Period Range 5 seconds to 3 minutes Timed Period Adjustment 9 seconds per turn Interrupt rate 80 per minute ± 20 Case Style Din with vertical Bracket Dimensions 94 x 61 x 36mm Weight 60g Fixing 1 Point Fixing Hole Size 5mm
Wiring Diagram
Suggested Adjustment Method: 1. First measure the timed period and make a note of its value (Time old). 2. To calculate the number of turns use the following formula:
Turns = (Time wanted – Time old) / 9. A positive value means turn the adjuster clockwise a negative value means turn the adjuster anti-clockwise
3. After adjusting the preset measure the Timed Period (Time old) 4. If timed period is accurate enough then finish if not repeat 2 and 3 above.
Page 3.7
E237 24V LAMP SIMULATOR
With the introduction of L.E.D. Lighting and low wattage bulbs, a problem has arisen in that L.E.D.s do not draw sufficient current for the Hazard Flashers to operate correctly. It may therefore be necessary for operator’s to fit a Lamp Simulator to enable the Hazard Flashers to work correctly. The Lamp Simulator works by making a pair of 5W 24V Bulbs behave electrically like a pair of 21W 24V Bulbs.
EURO MANUFACTURING AND MARKETING LIMITED Euro Works, 11 – 13 High Street, Wem, Shropshire SY4 5AA, UK
Tel.: +44 (0) 1939 235 073 Fax.: +44 (0) 1939 235 074 Email: [email protected] Web Site: www.eurogroup.gb.com
Page 3.8
PART NO: E237 DESCRIPTION 24V LAMP SIMULATOR SUPPLY CURRENT 5mA BULB SUPPLY VOLTAGE 18V – 30V DC EQUIVALENT BULB WATTAGE Pin 8 or Pin 4 = 24V
16W
CASE STYLE DIN PACK WITH VERTICAL BRACKET
DIMENSIONS 94mm X 61mm X 36mm WEIGHT 110g FIXING 1 POINT FIXING – 5mm HOLE
48V POWER FLASHER
E921 48V POWER FLASHER 4 X 21W 48V MAX The main application for this Unit is for Fork Lift Trucks, especially if they are used on the Highway or in areas where there are other Vehicles or Traffic so that they comply with the Law and Health & Safety Regulations.
Wiring Diagrams
PART NO DESCRIPTION CASE WEIGHT FIXING
E921 48V POWERFLASHER
DIN PACK + VERTICAL BRACKET 94mm X 61mm X 36mm
70g 1 POINT FIXING 5mm HOLE
EURO MANUFACTURING AND MARKETING LIMITED Euro Works, 11 – 13 High Street, Wem, Shropshire SY4 5AA, UK
Tel.: +44 (0) 1939 235 073 Fax.: +44 (0) 1939 235 074 Email: [email protected] Web Site: www.eurogroup.gb.com
Page 3.9
ELECTRONIC POWER FLASHER
This Unit was primarily designed to flash the Headlights alternately on Police Cars and Emergency Vehicles. There are 3 ways to wire the Flasher:- • As a Change-Over Flasher to Flash the Main Beams alternately • As a Change-Over Flasher 2 X 10A (2 X120W) Max • As a Standard Flasher 10A (120W) Max
Wiring Diagrams (Examples Shown are for E683 (PF12-10 C/O)
Page 3.10
PART NO DESCRIPTION WORKING VOLTAGE
CASE FIXING WEIGHT
E683
PF1210-C/O POWER FLASHER
12V DC
DIN PACK + VERTICAL BRACKET 94mm X 61mm X 36mm
1 POINT FIXING 5mm HOLE
70g
E699
PF2410-C/O POWER LASHER
24V DC
DIN PACK + VERTICAL BRACKET 94mm X 61mm X 36mm
1 POINT FIXING 5mm HOLE
70g
E988
PF1210-C/O POWER FLASHER 180 Flashes / Min
12V DC
DIN PACK + VERTICAL BRACKET 94mm X 61mm X 36mm
1 POINT FIXING 5mm HOLE
70g
E989
PF2410-C/O POWER LASHER 180 Flashes / Min
24V DC
DIN PACK + VERTICAL BRACKET 94mm X 61mm X 36mm
1 POINT FIXING 5mm HOLE
70g
16 PIN FLASHERS
This 16 Pin 24V Flasher offers a direct equivalent to the SCANIA 1401789 and HELLA 4DN 007 431 – 02
EURO MANUFACTURING AND MARKETING LIMITED Euro Works, 11 – 13 High Street, Wem, Shropshire SY4 5AA, UK
Tel.: +44 (0) 1939 235 073 Fax.: +44 (0) 1939 235 074 Email: [email protected] Web Site: www.eurogroup.gb.com
Page 3.11
PART NO
E023
DESCRIPTION
16 PIN FLASHER
WORKING VOLTAGE
24V DC
CROSS REFERENCE
1401789 (SCANIA) 4DN 007 431 – 02 (HELLA)
SPECIFICATION
2 + 1 + 1 (8) X 21W
CASE
BLACK ABS CASE WITH MOULDED BRACKET
DIMENSIONS
97mm HIGH X 95mm WIDE X 40mm DEEP
WEIGHT
161g