E2-1 Constant Pressure Pumping System · Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433

Davies Supply Group Ltd.

Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433

E2-1

Constant Pressure Pumping System

06/12/13

PENTEK INTELLIDRIVE™ Constant Pressure Control Center Maintains constant & consistent water pressure for residential well

pump systems by automatically adjusting motor speeds to meet changes in water demand. Instantaneous feedback from an electronic pressure transducer instructs the drive to change the pump motor speed to maintain constant pressure.

For use with both submersible and above ground well pumps Maintains constant water pressure, inside and outside, regardless of

how many people or appliances are using water at the same time Fully programmable with 34 adjustable programming parameters Extends the life of the pump and motor by using "Soft Start / Coast to

Stop" as well as eliminating frequent on/off pressure cycling Keypad with backlit LCD display has diagnostic and status indicators Ground detection detects and displays when there is a grounding

problem and shuts down the system until problem is corrected EMI/RFI filters eliminate potential interference Removable / replaceable terminal blocks Warranty: 12 months from original installation or 18 months from

manufacture Includes: Variable Frequency Drive with NEMA 3R outdoor

enclosure, Transducer (1/4" thread size, 18 NPT type) & Transducer Cable (10')

One #VFD-SGA Must be installed with each

Intellidrive™ Controller to preserve the Drive's warranty. See next page for information.

Motor Type HP Range Input Voltage Max Output Amps Enclosure Brand Part Number

2 Wire* 1 Phase

0.5 to 1 HP

190V to 265V

9.5A

NEMA 3R Outdoor

Pentek PID10 3 Wire* 1 Phase 7.5A

3 Phase 5A

2 Wire* 1 Phase 0.5 to 1.5 HP 11A

Pentek 3 Wire* 1 Phase 0.5 to 2 HP

13.5A

3 Phase 8.5A

3 Phase 0.5 to 5 HP 18A Pentek PID50

PID20

* Select drive by Service Factor amps of pump motor Note: 2 Wire Applications Only Compatible with PENTEK brand 2-Wire Motors

Pump Motor

Input Output PENTEK Control

2 Wire 1 Phase 1 Phase Up to 1 HP



Complete Product Range with 3 Models:



Storage tank not included. 200, 300 & 600 gallon poly tanks available. See "Water Storage Tanks"

in section F for more information. Call Davies, we can size a package for each

specific application!

E2-2


06/12/13

Will alternate pumps that are connected to the Pentek Intellidrive™ Controller

Designed to equalize wear on the pumps by alternating two Pentek Intellidrive VFD's every 24 hours. This panel alternates which pump is the lead and lag in a duplex system. It can also be used independently of the lead/lag function.

Alternate / Off Switch Indicators: Power On, Pump 1 Enabled & Pump 2 Enabled Connection: 4 Terminal Blocks to connect VFD's - Use 18 AWG

Wire

PENTEK INTELLIDRIVE™ Surge Protection Kit

Line Side Part Number

Service Wiring Peak Surge Current MCOV UL 1449, 3rd Ed,

V.P.R. Short Circuit Rating

EL 1449, 3rd Ed. In V.P.R.

Two Power Cords + Ground

72,000A/Phase 36,000A/Mode

130/260V 500 L-G, 900V L-L

10,000A 10,000A

Load Side

Service Wiring Peak Surge Current MCOV

Three Power Cords + Ground 75,000A 320V

VFD-SGA

One #VFD-SGA Must be installed with each Intellidrive™ Controller to preserve the Drive's warranty.

Line & Load side surge protection for use with any 230 Volt Pentek Drive

Line side arrester installed in the circuit breaker. Load side installed on the drive output.

Compact size to fit most applications and parallel connection for easy installation

Diagnostic LEDs to indicate system power and surge protection Weatherproof design allows for use in most environments Service Voltage: 240VAC (line side); 240VAC (load side) Auto reset to handle multiple surges

PENTEK INTELLIDRIVE™ Alternating Control Panel

Rated Volts, Hz Cord Enclosure H x W x D Weight Part Number

120 VAC, 50/60 6' NEMA 1 5.375" x 3.25" x 1.625" 1 lbs VFD-ALT

Constant Pressure Pump Package Pump Package for drip tank, cistern, reservoir and well applications

Not all package contents are

pictured

Application Part Number

Typical Application: Designed for rural low pressure water distribution systems

PIDPACK



E2-3


17/04/15

PENTEK PPC3 / PPC5 Variable Frequency Drive Series

PENTEK Pump Controllers innovative pumping solutions for maximizing pump functionality, optimizing pump system design and reducing operating energy costs

PENTEK PPC's can be used on all centrifugal

motor-driven pumps including close-coupled motor drive, frame mount, submersible and lineshaft turbine pumps, in a wide range of applications

PPC Features

The PENTEK PPC3 and PPC5 Pump Controllers are programmed with the PENTEK Assistant and pre-jumpered, providing ease of setup for constant pressure applications. The PENTEK Assistant defaults to pre-defined parameters and prompts the user for application-specific information. The 'Help' key activates parameter descriptions, providing easy reference to the programming guide.

PENTEK Assistant Guides the user through the setup process for constant pressure

applications, taking less than 2 minutes to program; allows for local or remote operation

Includes Macros for both submersible and above-ground pump applications

System harmonics evaluation process

Additional Application Functions Auto-Restart Functionality - re-starts pump after power loss Easily configured for constant flow applications by adjusting 2 additional

menu parameters Multiple System Setpoints or Operating Condition - includes 2

independent process control setpoints to allow operation under a second process

Time function supports 2 daily and weekly START/STOP/BOOST times

Process Benefits

Variable Speed Control Meets Requirements of process control with constant pressure at variable

flow conditions or constant flow at variable pressure conditions Reduced Energy Costs Calculated energy savings online using BEC2 software at www.bec2.net Pump Protection From loss of prime, dead head and blocked suction

Motor Protection From ground fault, short circuit, phase loss and imbalance, overload,

undervoltage and overvoltage System Protection (PPC3 only) From harmonics, featuring an input choke that exceeds the performance

of a fixed 5% impedance line reactor Phase Conversion The PPC5 will convert 1-phase power into 3-phase power, allowing the

use of a 3-phase motor The PPC3 is available in both 1 & 3 phase models

PPC3/PPC5 Comparison

Features PPC3 PPC5

HP Rating 1-30 1/2-200

Voltages 230, 460 230, 460, 575

Frequency 50/60 Hz 50/60 Hz

Floating Choke No Yes

Harmonic Signature Good Best

No. of Relays 1 3 (ext. to 6 available)

Digital Input 2 6

Multiple Pump Capable No Yes

Mod. Bus No Yes

Enclosure Type NEMA 1 NEMA 1, 12

The output current (or amps) of the PPC must be greater than or equal to the maximum rated motor current



E2-4


17/04/15

VARIOSPEED® Constant Pressure Control Solutions

The new VARIOspeed series of constant pressure controls offered by SJE-Rhombus are an economical, pre-engineered solution for variable speed pumping applications, including: Submersible Deep Well Pumps Booster Pumps Irrigation Pumps Easy Setup and Operation Energy Saving Phase Conversion VARIOspeed VFD can be used in application where three phase power is not available. The drive will convert 240V, single phase power into 240V, three phase power. A three phase motor must be used in all cases Thrust Bearing Control Motor Protection Output phase loss, ground fault, motor overload, motor over temperature Drive Protection Over voltage, input phase imbalance, under voltage, short circuit Automatic System Restart VARIOspeed VFD can be configured to automatically restart in Auto Mode after power loss, power spikes, brown outs and dry well conditions

Available HP Range (208-240V) 1.5 HP-20HP (480V) 7.5HP-20HP Models available for single phase or three phase supply

voltage Energy optomization control Enclosure Style VARIOspeed N1 - NEMA 1 indoor enclosure VARIOspeed 3R - NEMA 3R indoor/outdoor enclosure

(included pump circuit breaker & fan and thermostat on 7.5 - 20HP models)

Controls PID control Adjustable electronic overload Auto start on pressure drop (adjustable) Auto stop on low Hz (No-Flow - sleep mode) saves energy and

protects the pump Display 4 line / 20 character back-lit LCD display is easy to read Rotary / push button for quick menu navigation and

programming Green LED run indicator Red LED fault indicator Off/Auto selector switch Pressure Transducer 0-200 PSI, NEMA 4X rated, stainless steel, 1/4" NPT

connection, 20 ft. shield cable Experience the VARIOspeed Advantage! Parameters are pre-programmed at the factory Quick installation, simple start-up 100% factory-tested Low Pressure alarm (pipe burst or run dry protection) High Pressure protection System Fail log Includes pressure transducer UL/cUL listed 5 year limited warranty 1 year limited warranty on transducer

CONTINUED ON NEXT PAGE

VARIOspeed® N1



E2-5


17/04/15

VARIOSPEED® Constant Pressure Control Solutions

VARIOSPEED® N1 Controller Description Model Output Amp HP Input Phase Output Phase Ship Weight Part Number

VARIOspeed® N1, 240V VS21-7.0-N1 7.0 1.5 1 3 21 lbs. 1041350

VARIOspeed® N1, 240V VS21-10.0N1 10.0 3 1 3 22 lbs. 1041351

VARIOspeed® N1, 240V VS23-16.5-N1 16.5 5 3 3 21 lbs. 1041352

VARIOspeed® N1, 240V VS23-31.8-N1 31.8 7.5-10 3 3 31 lbs. 1041353



VARIOspeed® N1, 480V VS43-16.0-N1 16.0 7.5-10 3 3 31 lbs. 1041356

VARIOspeed® N1, 480V VS43-29.5-N1 29.5 15-20 3 3 38 lbs. 1041357

NOTE: HP rating is based on standard NEMA b 4-pole motor (used for indication only, use nameplate FLA for sizing). The output voltage of the VFD cannot exceed the incoming voltage. Example: 208V in, 208V out (max).

VARIOSPEED® 3R Control Panel

Description Model Output Amp HP Input Phase Output Phase Ship Weight Part Number

VARIOspeed® 3R, 240V VS21-7.0-N3R 7.0 1.5 1 3 31 lbs. 1030983

VARIOspeed® 3R, 240V VS21-10.0-N3R 10.0 3 1 3 32 lbs. 1030984


VARIOspeed® 3R, 240V VS23-31.8-N3R 31.8 7.5-10 3 3 35 lbs. 1030985



VARIOspeed® 3R, 480V VS43-16.0-N3R 16.0 7.5-10 3 3 47 lbs. 1039110

VARIOspeed® 3R, 480V VS43-29.5-N3R 29.5 15-20 3 3 47 lbs. 1039111

NOTE: HP rating is based on standard NEMA b 4-pole motor (used for indication only, use nameplate FLA for sizing). The output voltage of the VFD cannot exceed the incoming voltage. Example: 208V in, 208V out (max).

LINE/LOAD REACTORS (indoor/outdoor rated. Supplied separately) Line/Load Reactors Use with Model Dimensions (in.) Electrical Data Ship Weight Part Number

LR23-16.5-N3R VS21-7.0-3R, VS21-10.0.0-3R, VS23-16.5-3R 12x12x10 18A, 1.5mH 37 lbs. 1041535

LR23-45.0-N3R VS23-31.8-3R, VS23-45.0-3R 12x12x10 55A, 0.27mH 46 lbs. 1041536

LR23-58.0-N3R VS23-58.0-3R 12x12x10 83A, 0.17mH 47 lbs. 1041537





E2-6 06/12/13


Constant Pressure Controllers

Features & Benefits Constant Water Pressure with a wide range of

settings (25 to 80psi)

Soft Start feature prevents water hammer and increases motor life

Works with small pressure tanks or with larger tanks already in place

Smart Reset® Technology allows well recovery before restarting the pump

Single Phase input power with single phase motor performance (MonoDrive, MonoDriveXT)

Single Phase input power with three phase motor performance (SubDrive75,100,150,300)

Excellent radio frequency interference shielding

UL & CUL Listed

Built-in Diagnostics & Protection Surge Protection

Underload (low water)

Undervoltage

Locked Pump

Open Circuit

Short Circuit

Overheated Controller

Listed

Residential Water Systems City like water pressure Smaller tank saves space Landscape Irrigation Systems Even distribution of water in zones Eliminates need for separate system

Water Treatment Systems More efficient back flushing eliminates need for multiple pumps Geothermal Systems

Applications

What is SubDrive? SubDrive is Franklin Electric's Family of constant pressure controllers which includes SubDrive75, SubDrive100, SubDrive150 & SubDrive300 covering a range from 1/2 to 5 HP. SubDrive controllers are designed to provide constant pressure for three phase, three wire systems by continually monitoring and adjusting the pump speed to meet water supply demands. SubDrives also eliminate pressure cycling during long-running applications such as landscape irrigation and geothermal heat pump operation. All in all, SubDrives combine reliability and state-of-the art technology to provide well owners with a premium water system.

What is MonoDrive? MonoDrive and MonoDriveXT are designed to provide constant pressure for single phase, three wire systems - even those already in place. That means you can have constant pressure just by replacing a three wire control box!



E2-7 15/05/15


MonoDrive - Constant Pressure Controller Provides constant water pressure through variable speed control and

eliminates pressure cycling by adjusting pump performance to meet water demand

For single phase, 3 wire submersible pumps Designed to convert a conventional 1/2, 3/4 or 1 HP pump system to a

variable speed constant pressure system by simply replacing the pressure switch & installing this controller. No need to pull your existing single phase pump.

Constant pressure setting range of 25-80psi Water faucets can be installed between wellhead and controller Dimensions: 16.5" x 12.375" x 9" Built-in diagnostics and system protection

Input (From Power Source) Output (To Motor) Min Tank Size

Use With Enclosure Brand Part

Number Voltage Frequency Max Amps Frequency Max Amps

230 V (Single Phase)

60 Hz 5.7 A @ 1/2HP 8.7 A @ 3/4HP

11 A @ 1HP

Variable (30-60 Hz)

4.0 A @ 1/2HP 6.6 A @ 3/4HP 9.0 A @ 1HP

2 gallon (less than 12GPM)

or 4 gallon (12GPM or higher) OR larger tanks already in

place

1/2, 3/4 or 1 HP Pump

Mounted to a 1/2, 3/4 or 1

HP, 230 VAC,

1 Phase Motor

NEMA 1 (Indoors)

Franklin Electric

587-0203-110

NEMA 4 (Outdoors)

Franklin Electric

587-0203-114

MonoDriveXT - Constant Pressure Controller Provides constant water pressure through variable speed control and

eliminates pressure cycling by adjusting pump performance to meet water demand

For single phase, 3 wire submersible pumps Designed to convert a conventional 1.5 or 2 HP pump system to a

variable speed constant pressure system by simply replacing the pressure switch & installing this controller. No need to pull your existing single phase pump.

Constant pressure setting range of 25-80psi Water faucets can be installed between wellhead and controller NEMA 1 Dimensions: 16.5" x 12.375" x 9" NEMA 4 Dimensions: 17.5" x 16.375" x 11.375" Built-in diagnostics and system protection

Input (From Power Source) Output (To Motor) Min Tank Size

Use With Enclosure Brand Part

Number Voltage Frequency Max Amps Frequency Max Amps


60 Hz 13 A @ 1.5HP 16 A @ 2HP

Variable (30-60 Hz)

10 A @ 1.5HP 12 A @ 2HP

2 gallon (less than 12GPM)

or 4 gallon (12GPM or higher) OR larger tanks already in

place

1.5 or 2 HP Pump

Mounted to a 1.5 or 2 HP, 230 VAC,

1 Phase Motor

NEMA 4 (Outdoors)

Franklin Electric

587-0204-114



E2-8 17/04/15


Constant Pressure Pump Package Pump Packages for drip tank, cistern, reservoir and well applications

Not all package contents are pictured

Application Part Number

Typical Application: Designed for rural low pressure water distribution systems

MONOPACK2

Storage tank not included. 200, 300 & 600 gallon poly tanks available. See "Water Storage Tanks"

in section F for more information. Call Davies, we can size a package for each

specific application!

Inline CP - Motor, Pump, Drive & Pressure Switch In One Package All in one package makes installing a constant pressure system easy

for booster pump or flooded suction applications Three phase pump & motor performance using single phase input Small & compact design NEMA 4 electronics enclosure Multiple mounting configurations 1 1/4" NPT inlet & outlet Built-in diagnostics and system protection Ideal for new package installation

Flow Range

Product Power Rating

Min Incoming Pressure

Incoming Voltage

Pressure Adjustment

Range Frequency

Max Amps

Max Incremental Pressure Boost

Brand Part

Number

Up to 35 GPM

1.2 HP 3-5psi 230 VAC

Single Phase 25-80psi 60Hz 12 A 60psi Little Giant 90411101



E2-9 06/12/13


SubDrive Constant Pressure Controllers Provides constant water pressure through variable speed control and eliminates pressure cycling by adjusting pump

performance to meet water demand Three phase pump & motor performance using single phase input Constant pressure setting range of 25-80psi Water faucets can be installed between wellhead and controller Built-in diagnostics and system protection NEMA 1 Dimensions: 16.5" x 12.375" x 9" NEMA 4 Dimensions: 17.5" x 16.375" x 11.375" (except SubDrive300: 19.875" x 17.5" x 14.25") Ideal for new package installation

Input (From Power Source) Output (To Motor) Min Tank Size Use With Enclosure Brand

Part Number Voltage Frequency Max Amps Frequency Max Amps

SubDrive 75


60 Hz 11 A Variable (30-80 Hz) 5.9 A

2 gallon (less than 12GPM) or 4 gallon (12GPM or higher)

OR larger tanks already in place

3/4, 1 or 1.5 HP Pump

Mounted to a 1.5 HP,

230 VAC, 3 Phase Motor

NEMA 1 (Indoors)

Franklin Electric

587-0203-380

NEMA 4 (Outdoors)

587-0203-384

SubDrive 100


60 Hz 19 A Variable

(30-80 Hz) 8.1 A



1, 1.5 or 2 HP Pump

Mounted to a 2 HP,


NEMA 1 (Indoors)

Franklin Electric

587-0204-100

NEMA 4 (Outdoors)

587-0204-104

SubDrive 150


60 Hz 23 A Variable (30-80 Hz) 10.9 A



1.5, 2 or 3 HP Pump

Mounted to a 3 HP,


NEMA 1 (Indoors)

Franklin Electric

587-0204-150

NEMA 4 (Outdoors)

587-0204-154

SubDrive 300


60 Hz 36 A Variable

(30-80 Hz) 17.8 A

8 gallon (less than 12GPM) or 20

gallon (12GPM or higher) OR larger tanks already in

place

3 or 5 HP Pump

Mounted to a 5 HP,


NEMA 4 (Outdoors)

Franklin Electric 587-0206-300



E2-10 06/12/13


SubDrive 2W - Constant Pressure Controller

Input (From Power Source) Output (To Motor) Min Tank Size Use With Enclosure Brand

Part Number Voltage Frequency Max Amps Frequency Max Amps


60 Hz <12 A Variable

(30-60 Hz)

6.0 A @ 1/2HP 8.0 A @ 3/4HP 9.8 A @ 1HP

2 gallon (less than 12GPM) or

4 gallon (12GPM or higher) OR larger tanks

already in place

1/2, 3/4 or 1 HP Pump

Mounted to a 1/2, 3/4 or

1 HP, 230 VAC,

1 Phase Motor

NEMA 3R (Outdoors)

Franklin Electric

587-0203-223

Provides constant water pressure through variable speed control and eliminates pressure cycling by adjusting pump performance to meet water demand

For single phase, 2 wire submersible pumps Designed to convert a conventional 1/2, 3/4 or 1 HP pump system to a

variable speed constant pressure system by simply replacing the pres-sure switch & installing this controller

Maximum pump output is similar to the performance achieved using a conventional pressure switch. Therefore, the pump selection criteria are the same as if a pressure switch were used.

Constant pressure setting range of 25-80psi Water faucets can be installed between wellhead and controller Dimensions: 12.25" x 16.5" x 9" Built-in diagnostics and system protection

Allows a water system to alternate between two parallel pumps controlled by separate SubDrives

Push-button design to select switching interval, 1-24 hours or manual Safe operation using a 120VAC/12VAC outdoor rating and low

voltage wiring connection Fail Safe Design: System still produces water if Alternator is taken

offline NEMA 4 enclosure Applications: schools, restaurants, hospitals, carwashes, small

municipal water systems

SubDrive /Monodrive - Duplex Alternator

Power Source to Indoor/Outdoor Transformer

Power to Controller Pressure Adjustment Range

Brand Part

Number Voltage Frequency Voltage Frequency Power

115 VAC 60 Hz 12 VAC 60 Hz 1.4 Watts 25-80psi Franklin Electric

5850012000



E2-11 17/04/15

Constant Pressure Pumping System Accessories

Manifold Installation Kit Description Part Number

Manifold Installation Assembly Kit (Tank sold separately)

DRIVEPK

Pressure Sensor Kit

Kit Includes Part Number

Pressure sensor, pressure sensor boot, small screwdriver with Allen wrench and a 10' cable

223995901

Replacement Sensor for all MonoDrive and SubDrive models Pressure Adjustment Range: 25-80psi (factory set at 50psi)

Manifold & Bracket - Stainless Steel Manifold tapped with two 1", two 3/4" and one 1/4" threads 1" ports can be bushed down to match your tank and transducer 3/4" ports accommodate a relief valve and a hose bib, with a 1/4"

FPT port for a 2" or 2 1/2" dial, 1/4" centre back mount gauge Bracket allows for manifold to be secured to the brackets with "U"

bolts and a small pressure tank inserted to the manifold. Interchangeable bracket allows for two different mounting options

Description Part Number

Manifold - 1 1/4" MPT x 1" FPT line connections. 11" long 07M125SS

Bracket - kit for 1 1/4" manifold, steel with black powder coat finish, lag screws, "U" bolts, nylon lock nuts, and plastic end caps.

07M125MB

Manifold - 2" MPT x 1 1/2 FPT in-line connections, 13-3/4" long 07M200SS

Bracket - kit for 2" manifold, steel with black powder coat finish, lag screws, "U" bolts, nylon lock nuts, and plastic end caps.

07M200MB

Documents

E2-1 Constant Pressure Pumping System · Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433