Upload
others
View
24
Download
1
Embed Size (px)
Citation preview
© 2008 ALL RIGHTS RESERVED. Technical changes possible. No liability for mi sprints
VW Amarok 201 0 >VW Beetle 2011 >VW Caddy 2004 >VW EOS 2006 >VW Golf/Golf Plus/Cabrio 2003 >VW Jetta 2005 >VW Passat/Passat CC 2005 >
0
Installation Manual
Part No.: A11VW39002
Black
VW Polo 2009> VW Scirocco 2008 >VW Sharan 2010 >VW Tiguan 2007 >VW Touran 2003 >VW Transporter 2009 >VW Vento 2010 >
• (1) Metal Frame • (3) Installation Kit
• (2) Radioblende • (4) Mounting Frame
Installation Manual
VW Golf V only:
Pull up the aircone unit (fixed by
clips). Remove two Torx (TX20) screws
(see arrows) which become visible.
Remove the original trim
frame, surrounding the radio
(fixed by clips).
2. Remove the 4 Torx (TX20) screws
(These screws wi/1 be used again
/ater).
Remove the OEM head unit.
Ali installation work must be performed by a qualified professional installer on/y.
The manufacturer/ dealer is not fiable for any kind of incidential or indirect damages.
(sample photo)
Mount the metal brackets with
double OIN head unit
(sample photo)
(sample photo)
(sample photo)
The position of the copper co/oured
ho/der can be adjusted to your needs
for perfect fit. (see sample)
3. Connect all required circuit
points and push the double
OIN head unit until it snaps in.
Fix mounting frame with 4
orginal-Torx (TX20) screws,
place facia plate
4. lnstall everything in reverse Order
to finish installation
E01VW39002Volkswagen Steering Wheel Control Interface
Vehicle ApplicationVW Passat (B6, 3C, B7, 3C36) 2005 - 2015VW Golf (Mk5/Mk6) 2005 - 2015VW Touran 2003 - 2015VW Transporter 2003 - 2015VW Polo (9N, 9N3, 6R) 2005 - 2014VW Jetta 2005 - 2015VW EOS (1F) 2006 - 2015VW Tiguan (5N) 2007 - 2015VW Scirocco 2008 - 2015
Key Features
• Retains Steering Wheel Controls• Retains Factory Phone Buttons
• Provides Speed Pulse, Park Brake, Reverse Gear Outputs
The information provided in this document is subject to change without notice due to changes and/or improvements to the product/s.
V1. 05/18
VW Amarok (2H) 2010>VW Suran 2009>VW Vento 2005 - 2011VW Sagitar 2005 - 2011VW Magotan 2005 - 2011VW Fusca 2005 - 2011VW Touareg 2010>VW UP! 2011 - 2016
2
ABOUT THIS PRODUCT
E01VW39002CAN-Bus Steering Wheel Control Interface for Volkswagen vehicles with RCD200/300/310/ 500/510 original stereo and Quadlock connector
WIRING COLOUR CODESPurple Right Rear Speaker +Purple/Black Right Rear Speaker -Green Left Rear Speaker +Green/Black Left Rear Speaker -Grey Right Front Speaker +Grey/Black Right Front Speaker -White Left Front Speaker +White/Black Left Front Speaker -
Yellow Permanent 12VBlack GroundRed Ignition 12VOrange IlluminationPink Speed PulseGreen Park BrakePurple/White Reverse Gear
PRIOR TO INSTALLATIONRead the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are using during the installation to avoid damage to the vehicle or product. SETMA can not be held responsible for the installation of this product.
TECHNICAL SUPPORTSETMA want to provide a fast and suitable resolution to any problems encountered during installation of this product. To get in touch with our dedicated technical support team, please fill in a ticket at [email protected] and provide as much information as possible.
3
FITTING GUIDE1. Remove and disconnect the original head unit.
2. Connect the 12 way molex connector of the head unit patch lead (suppliedseparately) to the interface.
3. Connect the opposite end of head unit patch lead to the head unit steeringwheel control input on the back of the aftermarket head unit.
NB: This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information onwhere to connect.
Important: This step must be completed before connecting power to the interface. Failure to so do may result in no steering wheel control function.
4. Connect the 14 way molex connector to the interface
5. Connect the male power/speaker ISO harness to the female power/speaker ISO har-ness from the aftermarket head unit. For aftermarket head units without an ISOconnector, please refer to “Wiring Colour Codes” on Pg. 2.
4
FITTING GUIDE
STEERING WHEEL CONTROL FUNCTIONALITY
6. Connect the female vehicle specific connectors on the harness to the male vehicleconnector from the vehicle. Test head unit for correct operation.
FunctionVolume +Volume -Track +Track -Pick Up (Short Press)Hang Up (Long Press)Mute
Original ButtonVolume +Volume -Right ArrowLeft ArrowPhone ButtonPhone ButtonMute
FunctionVolume +Volume -Track +Track -SourceMuteMenu
Original ButtonVolume +Volume -Up ArrowDown ArrowOKStarMenu
Config 1.
Config 2.
Universel Patch Lead
Configuration Assignments (1=Link made, O=No Link)
Jl Systems
1 0 0 JVC
0 1 0 BEAT/Philips/Nakamichi
1 1 0 Clarion
0 0 1 Kenwood
1 0 1 Alpine
0 1 1 Panasonic
1 1 1 Sony/LG/Pioneer
1 (Pin12) 1 (PinlO} 0 Zenec
1 1 1 Chinese Learning Brands
Here are some Examples of how to make various patch Leads:
Example 1: Alpine - Remove Link J2 then use the Jack connector into radio.
Example 2: Kenwood - Remove Link J1 and J2, use the wire connector to Radio.
Example 3: Zenec - Remove Link J3, Cut Orange and Green then solder top row (Pin 12 & 10) together and lnsulate. Use the Wire connector to Radio.
Universal Patch Lead
Examples:
Solder Joint
Connector
Jack/Keyl
Keyl
Jack
Keyl
Jack
Keyl
Jack
Keyl
Keyl, Key2, GND
ZENEC ALPINE
E02UN00001
Pin Configuration
Pin 1 Descrintion
1 Reserved 2 Reserved 3 Reserved
4 Analoa 2 Swc -
5 GND Swc -
6 Analog 1 Swc C
7 Link J3
! 8 Link J3 9 Link J2 10 Link J2 -
11 Link J1 -
12 Link J1 -
KENWOOD