DYNSIM PowerHigh Fidelity Dynamic Simulation for the Power Industry

DYNSIM Power is an advanced, unified power plant modeling simulation used throughout the life of a power plant by creating dynamic simulation models. This solution is integrated with DYNSIM, reducing plant startup time. This simulation software validates controls and produces an environment to properly train operators.

DYNSIM Power

SUMMARY

Advanced, unified power plant modeling environment. Create flexible, dynamic simulation models that can be combined with a DCS simulation for Engineering validation and control system checkout. Produce an integrated modeling and instructor framework for operator training.

BUSINESS VALUE

• Leverage the combined modeling power of DYNSIM, used in over 100 simulators worldwide

• Decrease operator training and start up periods

• Benefit from a complete set of equipment models, saving engineering and simulation time

IntroductionSimSci™ DYNSIM® Power is an advanced, unified power plant modeling environment for use throughout a power plant’s life cycle. Create flexible dynamic simulation models that can be combined with a DCS simulation for Engineering validation, control system checkout, and ultimately produce an integrated modeling and instructor environment to train operators. Simulate any of the following typical power plant designs:

• Conventional Drum-unit Gas, Oil, or Pulverized Coal-fired Power Plants

• Once-through Supercritical Gas, Oil, or Pulverized Coal-fired Power Plants

• Gas Turbine and Combined Cycle Plants

The unique DYNSIM Power solution is attributed to the SimSci core DYNSIM product for oil and gas modeling to provide an integrated project resolution that is unrivaled in the industry - proven in over 100 simulators worldwide:

• Integrated Gasification Combined Cycle (IGCC)

• Combined LNG Terminal/Power Plant

• Refinery Steam Generation and Distribution

01

Accurate heat transfer calculation

Easy-to-Use DYNSIM Power GUI

DYNSIM Power

Unit Operations/ModelsBenefit from a complete set of equipment models to rigorously simulate a variety of power plants:

Furnaces Boiler Heat Exchangers• Belt feeders • Cyclone separator • Condenser• Coal Pulverizers • Downcomers • Evaporative cooler• Gas, coal, and oil fuel • Steam drums • 3-region feed water heaters• Radiation gas nodes • Once through risers • 2 & 3 sector regenerative exchangers • Superheater bundles

Steam Turbines Flow Components Environmental• Exhaust hood • Fan with guide vanes • Flue gas scrubbers• Extraction header • Header • Limestone handling• Governor valve • Heat exchanger • Selective catalytic reduction (SCR)• Reaction stages • Pipe• Steam chest • Pump• Turbine stress • Tank• Metal nodes for turbine soak • Valve

Electrical Other Models Controls• Bus • Gas turbines • And• Circuit breaker • Torque shaft • Calculation• Circuit disconnect • Emissions • Counter• Electrical load • Feedwater chemistry • Custom logic• Exciter • Opacity • Dual input switch• Generator with V-curves • Soot blowing • Function generator• Motor • Bearing vibrations • Latch• Power source/sink • Bearing temperatures • Lead/lag• Synchronization key • Lube oil systems • Master• Synchronization scope • Or• Transformer • PID controller• Voltage regulator • Pulse positioner • Rate limit • Summation • Timer

System

Instructor Features• Administrator, engineer, instructor & operator access modes• Integrated model building graphical user interface• Built in Control cross-referencing• Snapshots for initial conditions and backtracks• Built-in model malfunctions

• Scenarios• Trainee performance monitoring• Trends• Remote Functions / Field Operated Devices

Connectivity• Microsoft Excel® • OPC• SCP • TRISIM Plus™ (for Triconex)• Customized Solutions

02

© 2014 Invensys Systems, Inc. All rights reserved. Invensys, Avantis, SimSci and Wonderware are trademarks of Invensys Systems, Inc., its subsidiaries or affiliates. All other brands and product names may be trademarks of their respective owners.

Invensys Systems, Inc. 26561 Rancho Pkwy South, Lake Forest, CA 92630 Telephone: +1 (949)-727-3200 Fax: +1 (949)-727-3270 software.invensys.com

DYNSIM Power03

.

PN SS-0131 Rev. 08/14

Dynamic Simulation Suite DYNSIM Power is part of the Dynamic Simulation Suite (DSS) of products. DSS provides full-power rigorous dynamic simulation for plant engineers, operators, and managers to use in optimizing plant operations and design. DSS is comprised of DYNSIM, SCP, TRISIM Plus, and Operator Training programs; offering a professional grade alternative to dated, fragmented and hard-to-use products with which many plants currently struggle. All DSS products can communicate with each other, allowing a perfect combination to suit your exact plant requirements.

Process Overview graphics built in DYNSIM Power