8/10/2019 Dynamics of Machinery Lab COURSE PLAN

1/4

BHARATHIYAR COLLEGE OF ENGINEERING AND TECHNOLOGY

KARAIKAL

DEPARTMENT OF MECHANICAL ENGINEERING

COURSE PLAN 2010-2011

Subject: Dynamics of Machinery Lab (MEP 52) IIIMech A sec

Class / semester: B.Tech / V

Total number of students : 70 Period : 15 weeks

No. of batches : 02 No.of cycle: 1

No. of students / batch :

I Batch : 35

II Batch : 35

List of experiments:

1.

Demonstration of four bar inversion mechanism

2.

Natural frequency of single mass, single helical spring system.

3.

Natural frequency of combination of springssprings in parallel, springs in series

4.

Natural frequency of undamped torsional single rotor, double rotor system. Effect

of inertia (I) and stiffness (kt).

5.

Determination of radius of gyration of a given compound pendulum

6.

Determination of radius of gyration, moment of inertiabifilar suspension

methodtrifilar suspension method

7.

Damping coefficient of torsional single rotor systemEffect of depth of immersion in oil and

damping ratio

8.

Resonance frequency of equivalent spring mass systemundamped and damped

condition. To plot amplitude Vs frequency graph for different damping.

9.

Determination of characteristic curves of Watt, Porter, Proell and spring loaded governors.

10.

Static and Dynamic balancing.

11.

Whirling of shafts/ determination of critical speed with and with out Rotors.

12.

Gyroscopic couple verification.

13.

Journal bearingpressure distribution of different loads at different Speeds.

14.

Cam motion analysis.

15.

Generation of involute gear profile.

16.

Tracing of coupler curves.

17.

Determination of error in straight line drawn by watt chain mechanism.

8/10/2019 Dynamics of Machinery Lab COURSE PLAN

2/4

BHARATHIYAR COLLEGE OF ENGINEERING AND TECHNOLOGY

KARAIKAL

DEPARTMENT OF MECHANICAL ENGINEERING

COURSE PLAN 2010-2011

Subject : Mechanical Measurment and Metrology Lab IIIMech B sec

Class / semester : B.Tech / VI

Total number of students : 69 Period : 15 weeks

No. of batches : 2 No. Of cycle: 1

No. of students / batch :

I Batch : 35

II Batch : 34

List of experiments :

1.

Demonstration of four bar inversion mechanism2.

Natural frequency of single mass, single helical spring system.

3.

Natural frequency of combination of springssprings in parallel, springs in series

4.

Natural frequency of undamped torsional single rotor, double rotor system. Effect

of inertia (I) and stiffness (kt).

5.

Determination of radius of gyration of a given compound pendulum

6.

Determination of radius of gyration, moment of inertiabifilar suspension

methodtrifilar suspension method

7.

Damping coefficient of torsional single rotor systemEffect of depth of immersion in oil and

damping ratio

8.

Resonance frequency of equivalent spring mass system

undamped and damped

condition. To plot amplitude Vs frequency graph for different damping.

9.

Determination of characteristic curves of Watt, Porter, Proell and spring loaded governors.

10.

Static and Dynamic balancing.

11.

Whirling of shafts/ determination of critical speed with and with out Rotors.

12.

Gyroscopic couple verification.

13.

Journal bearingpressure distribution of different loads at different Speeds.

14.

Cam motion analysis.

15.

Generation of involute gear profile.

16.

Tracing of coupler curves.

17.

Determination of error in straight line drawn by watt chain mechanism.

8/10/2019 Dynamics of Machinery Lab COURSE PLAN

3/4

BHARATHIYAR COLLEGE OF ENGINEERING AND TECHNOLOGY

KARAIKAL

DEPARTMENT OF MECHANICAL ENGINEERING

COURSE PLAN 2010-2011

Subject: Mechanical Measurements and Metrology Lab IIIMech B sec

Class / semester: B.Tech / VI

Total number of students : 62 Period : 13 weeks

No. of batches : 2 No.of cycle: 1

No. of students / batch :

8/10/2019 Dynamics of Machinery Lab COURSE PLAN

4/4

I Batch : 31

II Batch : 31

List of experiments:

1.

Calibration of Micrometer

2.

Measurement of taper using Sine Bar

3.

Calibration of Plain Plug Gauge

4.

Straightness and Flatness Measurement using Autocollimator

5.

Surface Roughness Measurement

6.

Inspection of Screw Threads (Effective Diameter)

7.

Calibration of Inclined Tube Manometer

8.

Measurement of Pressure using Strain Gauges

9.

Determination of the constant of Thermocouples

10.

Measurement of Force using Transducers

11.

Measurement of Strain using Strain gauge

12.

Study of Displacement using LVDT and RVDT

13.

Vibration Measurement using Accelerometer