Upload
kenneth-gilbert
View
69
Download
3
Embed Size (px)
Citation preview
DX4Mac Pro 2008
Installation Instructions
Forward: The material in this manual is for information only and may change without notice. Trans International reserves the right to make changes in product de-sign or this manual without obligation to notify any person or persons. Trans International has made reasonable efforts in preparing this manual to make installation of DX4 as easy as possible, but Trans international assumes no li-
ability resulting from errors or omissions in this manual, or from the use of the installation instructions referred to in this manual.
All trademarks mentioned in this manual are the property of their respective owners.
All material © 2009 Trans International.
Installing the DX48-core Mac Pro
1. Turn off the computer.
NOTE: Do not open the computer or install items inside it
while it is on.
2. Unplug all external cables from the computer except the
power cord.
3. Let the computer’s internal components cool down before (5
to 10 minutes) opening the computer.
4. Touch the top of the computer to discharge any static elec-
tricity.
NOTE: To avoid generating static electricity, do not walk
around the room until you have finished working.
5. Unplug the power cord.
6. Remove the side panel of the Mac Pro by holding the side
panel and lifting the latch on the back of the computer.
NOTE: When replacing side panel make sure the latch is
in the up position. If the latch is down, the access panel
will not seat correctly in the enclosure.
1 DX4 Installation Manual Mac Pro 2008
7. Remove 1st, 2nd and 3rd drive sleds from the machine.
See Sketch 1.
8. Loosen the two thumbscrews on the PCI bracket and remove
if full length PCIe cards are installed. See Sketch 2.
SKETCH 2
Loosen both screws holding PCI bracket and remove the bracket.
PCIe card
2 DX4 Installation Manual Mac Pro 2008
SKETCH 1
9. Lift up on CPU cover from back edge and remove it. See
Sketch 3.
SKETCH 3
10. Remove both screws that holds fan assembly in place. one
at the upper right corner and second at the lower right front
corner. See Sketch 4.
SKETCH 4
3 DX4 Installation Manual Mac Pro 2008
11. Slide the fan assembly out by pulling as low as possible on
the assembly and wiggle it as you pull. See Sketch 5.
SKETCH 5
12. Locate and disconnect power cable from its socket. See
Sketch 6
SKETCH 6
Press release latch before removing cable
4 DX4 Installation Manual Mac Pro 2008
13. Connect DX4 power cable to the machine. See sketch 7.
14. Slide the fan assembly back in its place and secure it with
screw.
15. Install CPU cover back in it’s place by aligning the bottom
front edge of the CPU cover and then rotating the top back
till it snaps into place. See sketch 8
SKETCH 7
SKETCH 8
5 DX4 Installation Manual Mac Pro 2008
16. Mount drives in DX4 housing. See sketch 9.
17. Mount 3.5” drive on DX4 (if you have one). See sketch 10
SKETCH 9
SKETCH 10
6 DX4 Installation Manual Mac Pro 2008
18. Install SATA host adapter in PCie slot and any other cards
which were removed in step 8. See sketch 11
19. Connect signal cable to PCIe card.
20. Connect signal and power cable to drives in DX4.
See sketch 12.
SKETCH 11
i. Align and insert PCIe card in one of the open PCIe slots.
ii. Replace and tighten both screws after installing PCIe card.
PCIe card
SKETCH 12
7 DX4 Installation Manual Mac Pro 2008
21. Slide DX4 in 3rd drive bay of Mac pro. See Sketch 13.
22. Slide 1st and 2nd drive sleds back in Mac Pro drive bay’s.
See Sketch 14.
23. Replace side panel, reconnect all the cable back to the
machine, turn on the machine and follow instructions of
PCIe card to initialize the new drives installed in DX4.
SKETCH 13
SKETCH 14
8 DX4 Installation Manual Mac Pro 2008