DVD BBK Dv314s 1389 Service Manual

7/25/2019 DVD BBK Dv314s 1389 Service Manual

1/41

SERVICE MANUAL

DV314S


2/41

32

19


3/41

1.1 GENERAL GUIDELINES

1.When servicing,observe the original lead dress.ifa short circuit is found,replace all parts which have

been overheated or damaged by the short circuit.

2.After servicing,see to it that all the protective devices such as insulation barrier,insulation papers

shields are properly installed.

3.After servicing,make the following leakage current checks to prevent the customer from being exposed

to shock hazards.

Some semiconductor(solid state)devices can be damaged easily by static electricity.Such components

commonly are called Electrostatically Sensitive(ES)Devices.Examples of typical ES devices are integrated

circuits and some field-effect transistorsand semiconductor chip components.The following techniques

should be used to help reduce the incidence of component damage caused by electro static discharge(ESD).

1.Immediately before handling any semiconductor component or semiconductor-equipped assembly,drain

off any ESDon your body by touching a known earth ground.Alternatively,obtain and wear a commercially

availabel discharging ESD wrist strap,which should be removed for potential shock reasons prior to

applying power to the unit under test.

2.After removing an electrical assembly equipped with ES devices,place the assembly on a conductive

surface such as alminum foil,to prevent electrostatic charge buildup or exposure of the assembly.

3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4.Use only an anti-static solder removal device.Some solder removal devices not classified as anti-static

(ESD protected)can generate electrical charge sufficient to damage ES devices.

5.Do not use freon-propelled chemicals.These can generate electrical charges sufficient to damage ES

devices.

6.Do not remove a replacement ES device from its protective package until immediately before you are

ready to install it.(Most replacement ES devices are packaged with leads electrically shorted together by

conductive foam,alminum foil or comparable conductive material).

7.Immediately before removing the protective material from the leads of a replacement ES device,touch

the protective material to the chassis or circuit assembly into which the device will be installed.

CautionBe sure no power is applied to the chassis or circuit,and observe all other safety precautions.

8.Minimize bodily motions when handling unpackaged replacement ES devices.(Otherwise harmless motion

such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can

generate static electricity(ESD).

notice (1885x323x2 tiff)

1. SAFETY PREAUTIONS

2.PREVENTION OF ELECTRO STATIC DISCHARGE(ESD)TOELECTROSTATICALLY SENSITIVE(ES)DEVICES

1


4/41

Front Panel Illustration

32 5 64 7

8

2 Disctray

8 MIC VOLUMEknob

9

3 IR SENSORbutton

MICjack9

POWERswitch

5 OPEN/CLOSEbutton

6 PLAY/ buttonPAUSE

STOPbutton7

4 Display window

2


5/41

The laser diode in the traverse unit (optical pickup)may brake down due to static electricity of clothes or human

body.Use due caution to electrostatic breakdown when servicing and handling the laser diode.

4.1.Grounding for electrostatic breakdown prevention

Some devices such as the DVD player use the optical pickup(laser diode)and the optical pickup will be damaged

by static electricity in the working environment.Proceed servicing works under the working environment where

grounding works is completed.

4.1.1. Worktable grounding

1.Put a conductive material(sheet)or iron sheet on the area where the optical pickup is placed,and ground the

4.1.2.Human body grounding

1 Use the anti-static wrist strap to discharge the static electricity from your body.

4.1.3.Handling of optical pickup

1.To keep the good quality of the optical pickup maintenance parts during transportation and before

installation,the both ends of the laser diode are short-circuited.After replacing the parts with new ones,

remove the short circuit according to the correct procedure.(See this Technical Guide).

2.Do not use a tester to check the laser diode for the optical pickup .Failure to do so willdamage the laser

diode due to the power supply in the tester.

4.2.Handling precautions for Traverse Unit (Optical Pickup)

1.Do not give a considerable shock to the traverse unit(optical pickup)as it has an extremely high-precise

structure.

2.When replacing the optical pickup,install the flexible cable and cut is short land with a nipper.See the

optical pickup replacement procedure in this Technical Guide.Before replacing the traverse unit,remove

the short pin for preventingstatic electricity and install a new unit.Connect the connector as short times as

possible.

3.The flexible cable may be cut off if an excessive force is applied to it.Use caution when handling the cable

4.The half-fixed resistor for laser power adjustment cannot be adjusted.Do not turn the resistor.

safety_3 (1577x409x2 tiff)

sheet.

3

4.PREVENTION OF STATIC ELECTRICITY DISCHARGE


6/41

5.1Optical pickup UnitExplosed View and Part List

Pic (1)

5. Assembling and disassembling the mechanism unit

4


7/41

Materials to Pic (1)

No. PARTS CODE PARTS NAME Q ty

14692200 SF-HD60 1

1 1EA0311A06300 ASSY, CHASSIS, COMPLETE 1

2 1EA0M10A15500 ASSY, MOTOR, SLED 1

Or 1EA0M10A15501 ASSY, MOTOR, SLED 1

3 1EA2451A24700 HOLDER, SHAFT 3

4 1EA2511A29100 GEAR, RACK 1

5 1EA2511A29200 GEAR, DRIVE 1

6 1EA2511A29300 GEAR, MIDDLE, A 1

7 1EA2511A29400 GEAR, MIDDLE, B 18 1EA2744A03000 SHAFT, SLIDE 1

9 1EA2744A03100 SHAFT, SLIDE, SUB 1

10 1EA2812A15300 SPRING, COMP, TYOUSEI 3

11 1EA2812A15400 SPRING, COMP, RACK 1

21 1EA0B10B20100 ASSY, PWB 1

Or 1EA0B10B20200 ASSY, PWB 1

31 SEXEA25700--- SPECIAL SCREW BIN+-M2X11 3

32 SEXEA25900--- SPECIAL SCREW M1.7X2.2 2

33 SFBPN204R0SE- SCR S-TPG PAN 2X4 2

34 SFSFN266R0SE- SCR S-TPG FLT 2.6X6 1

35 SWXEA15400--- SPECIAL WASHER 1.8X4 X0.25 2

Note : This parts list is not for service parts supply.

5


8/41

5.2 BracketExplosed View and Part List

Pic (2)

Materials to Pic(2)

1.bracket 14. front silicon rubber

2.belt 15. Back silicon rubber

3.screw 16. Pick-up

4.belt wheel 17. Pick-up

5.gearwheel 18. switch

6.iron chip 19. Five-pin flat plug

7. Immobility mechanism equipment 20. screw

8. Magnet 21. PCB

9. Platen 22. motor

10. Bridge bracket 23. Motor wheel

11. screw 24. screw

12. screw 25.tray

13. Big bracket

Before going process with disassembly and installation, please carefully both

peruse the chart and confirm the materials.

6


9/41

5.3 MISCELLANEOUS

5.3.1 Protection of the LD(Laser diode)

Short the parts of LD circuit pattern by soldering.

5.3.2 Cautions on assembly and adjustment

Make sure that the workbenches,jigs,tips,tips of soldering irons and measuring instruments are

grounded,and that personnel wear wrist straps for ground.

Open the LD short lands quickl y with a soldering iron after a circuit is connected.

Keep the power source of the pick-up protected from internal and external sources of electricalnoise.

Refrain from operation and storage in atmospheres containing corrosive gases (such as H2S,SO2,

NO2 and Cl2)or toxic gases or in locations containing substances(especially from the organic silicon,cyan,

formalin and phenol groups)which emit toxic gases.It is particularly important to ensure that none of the

above substances are present inside the unit.Otherwise,the motor may no longer run.

7


10/41

6.1. Video Output (Luminance Signal) Confirmation

DO this confirmation after replacing a P.C.B.

Purpose:To maintain video signal output compatibility.

1.Connect the oscilloscope to the video output terminal and terminate at 75 ohms.

2.Confirm that luminance signal(Y+S)level is 1000mVp-p30mV

Measurement point

Video output terminal

Color bar 75%

PLAY(Title 46):DVDT-S15


DVDT-S15

or

DVDT-S01

Mode Disc

Measuring equipment,tools

200mV/dir,10 sec/dir 1000mVp-p30mV

Confirmation value

6.Electrical Confirmation

8


11/41

Do the confirmation after replacing P.C.B.

Purpose:To maintain video signal output compatibility.

1.Connect the oscilloscope to the video output terminal and terminate at 75 ohme.

2.Confirm that the chrominance signal(C)level is 621 mVp-p30mV

Measurement point

Video output terminal

Color bar 75%



DVDT-S15

or

DVDT-S01

Mode Disc

Measuring equipment,tools Confirmation valueScrewdriver,Oscilloscope

200mV/dir,10 sec/dir 621mVp-p30mV

6.2 Video Output(Chrominance Signal) Confirmation

9


12/41

7.MPEG BOARD CHECK WAVEFORM

7.1 27MHz WAVEFORM

7.2 IC VIPER22 PIN.5 WAVEFORM DIAGRAM

10


13/41

This Data Sheet states AMDs current technical specifications regarding the Product described herein. This DataSheet may be revised by subsequent versions or modifications due to changes in technical specifications.

Publication# 22358 Rev: B Amendment/+3Issue Date: November 10, 2000

16 Megabit (2 M x 8-Bit/1 M x 16-Bit)

CMOS 3.0 Volt-only Boot Sector Flash Memory

DISTINCTIVE CHARACTERISTICS

Single power supply operation

Full voltage range: 2.7 to 3.6 volt read and writeoperations for battery-powered applications

Regulated voltage range: 3.0 to 3.6 volt read andwrite operations and for compatibility with highperformance 3.3 volt microprocessors

Manufactured on 0.23m process technology

Fully compatible with 0.32 m Am29LV160B device

High performance Access times as fast as 70 ns

Ultra low power consumption (typical values at5 MHz)

200 nA Automatic Sleep mode current

200 nA standby mode current

9 mA read current

20 mA program/erase current

Flexible sector architecture

One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, andthirty-one 64 Kbyte sectors (byte mode)

One 8 Kword, two 4 Kword, one 16 Kword, andthirty-one 32 Kword sectors (word mode)

Supports full chip erase

Sector Protection features:

A hardware method of locking a sector to preventany program or erase operations within that sector

Sectors can be locked in-system or viaprogramming equipment

Temporary Sector Unprotect feature allows codechanges in previously locked sectors

Unlock Bypass Program Command

Reduces overall programming time when issuingmultiple program command sequences

Top or bottom boot block configurationsavailable

Embedded Algorithms

Embedded Erase algorithm automaticallypreprograms and erases the entire chip or anycombination of designated sectors

Embedded Program algorithm automaticallywrites and verifies data at specified addresses

Minimum 1,000,000 write cycle guaranteeper sector

20-year data retention at 125C

Reliable operation for the life of the system

Package option

48-ball FBGA

48-pin TSOP

44-pin SO

CFI (Common Flash Interface) compliant

Provides device-specific information to thesystem, allowing host software to easilyreconfigure for different Flash devices

Compatibility with JEDEC standards

Pinout and software compatible with single-power supply Flash

Superior inadvertent write protection

Data# Polling and toggle bits

Provides a software method of detecting programor erase operation completion

Ready/Busy# pin (RY/BY#)

Provides a hardware method of detectingprogram or erase cycle completion (not availableon 44-pin SO)

Erase Suspend/Erase Resume

Suspends an erase operation to read data from,or program data to, a sector that is not beingerased, then resumes the erase operation

Hardware reset pin (RESET#)

Hardware method to reset the device to readingarray data

11

8. Am29LV160D


14/41

Am29LV160D

PRODUCT SELECTOR GUIDE

Note:See AC Characteristics for full specifications.

BLOCK DIAGRAM

Family Part Number Am29LV160D

Speed Option Voltage Range: VCC= 2.73.6 V -70 -90 -120

Max access time, ns (tACC) 70 90 120

Max CE# access time, ns (tCE) 70 90 120

Max OE# access time, ns (tOE) 30 35 50

Input/OutputBuffers

X-Decoder

Y-Decoder

Chip EnableOutput Enable

Logic

Erase VoltageGenerator

PGM VoltageGenerator

TimerVCCDetector

StateControl

CommandRegister

VCC

VSS

WE#

BYTE#

CE#

OE#

STB

STB

DQ0DQ15 (A-1)

Sector Switches

RY/BY#

RESET#

DataLatch

Y-Gating

Cell Matrix

AddressLatch

A0A19

12


15/41

CONNECTION DIAGRAMS

A1

A15

A18

A14

A13

A12

A11

A10

A9

A8

A19NC

WE#

RESET#

NC

NC

RY/BY#

A17

A7

A6

A5

A4

A3

A2

1

16

2

3

4

5

6

7

8

17

18

19

20

21

22

23

24

910

11

12

13

14

15

A16

DQ2

BYTE#

VSSDQ15/A-1

DQ7

DQ14

DQ6

DQ13

DQ9

DQ1

DQ8

DQ0

OE#VSS

CE#

A0

DQ5DQ12

DQ4

VCCDQ11

DQ3

DQ10

48

33

47

46

45

44

43

42

41

4039

38

37

36

35

34

25

32

31

30

29

28

27

26

A1

A15

A18

A14

A13

A12

A11

A10

A9

A8

A19

NC

WE#

RESET#

NC

NC

RY/BY#

A17

A7

A6

A5

A4A3

A2

1

16

2

3

4

5

6

7

8

17

18

19

20

2122

23

24

9

10

11

12

13

14

15

A16

DQ2

BYTE#

VSSDQ15/A-1

DQ7

DQ14

DQ6

DQ13

DQ9

DQ1

DQ8

DQ0

OE#VSSCE#

A0

DQ5

DQ12

DQ4

VCCDQ11

DQ3

DQ10

48

33

47

46

45

44

43

42

41

40

39

38

37

36

35

34

25

32

31

30

29

2827

26

Reverse TSOP

Standard TSOP

13


16/41

A

CONNECTION DIAGRAMS

Special Handling Instructions

Special handling is required for Flash Memory products

in FBGA packages.

Flash memory devices in FBGA packages may be

damaged if exposed to ultrasonic cleaning methods.

The package and/or data integrity may be compromised

if the package body is exposed to temperatures above150C for prolonged periods of time.

1

2

34

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

22

RESET#

A18

A17A7

A6

A5

A4

A3

A2

A1

A0

CE#

VSSOE#

DQ0

DQ8

DQ1

DQ9

DQ2

DQ10DQ3

DQ11

44

43

4241

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

2524

23

WE#

A19

A8A9

A10

A11

A12

A13

A14

A15

A16

BYTE#

VSSDQ15/A-1

DQ7

DQ14

DQ6

DQ13

DQ5

DQ12DQ4

VCC

SO

A1 B1 C1 D1 E1 F1 G1 H1

A2 B2 C2 D2 E2 F2 G2 H2

A3 B3 C3 D3 E3 F3 G3 H3

A4 B4 C4 D4 E4 F4 G4 H4

A5 B5 C5 D5 E5 F5 G5 H5

A6 B6 C6 D6 E6 F6 G6 H6

D Q1 5/A-1 VSSBYTE#A16A15A14A12A13

DQ13 DQ6DQ14DQ7A11A10A8A9

VCC DQ4DQ12DQ5A19NCRESET#WE#

DQ11 DQ3DQ10DQ2NCA18NCRY/BY#

DQ9 DQ1DQ8DQ0A5A6A17A7

OE# VSSCE#A0A1A2A4A3

FBGATop View, Balls Facing Down

14


17/41

PIN CONFIGURATION

A0A19 = 20 addresses

DQ0DQ14 = 15 data inputs/outputs

DQ15/A-1 = DQ15 (data input/output, word mode),

A-1 (LSB address input, byte mode)

BYTE# = Selects 8-bit or 16-bit mode

CE# = Chip enable

OE# = Output enable

WE# = Write enable

RESET# = Hardware reset pin

RY/BY# = Ready/Busy output

(N/A SO 044)

VCC = 3.0 volt-only single power supply

(see Product Selector Guide for speed

options and voltage supply tolerances)

VSS = Device ground

NC = Pin not connected internally

LOGIC SYMBOL

20

16 or 8

DQ0DQ15(A-1)

A0A19

CE#

OE#

WE#

RESET#

BYTE# RY/BY#(N/A SO 044)

15


18/41

SDRAM 16Mb H-die(x16) CMOS SDRAM

Rev. 1.4 May 2004

The K4S161622H is 16,777,216 bits synchronous high data rate Dynamic RAM organized as 2 x 524,288 words by 16 bits, fabricated

with SAMSUNGs high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock I/

O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable laten-

cies allow the same device to be useful for a variety of high bandwidth, high performance memory system applications.

3.3V power supply

LVTTL compatible with multiplexed address

two banks operation

MRS cycle with address key programs

-. CAS Latency ( 2 & 3)

-. Burst Length (1, 2, 4, 8 & full page)

-. Burst Type (Sequential & Interleave)

All inputs are sampled at the positive going edge of the system clock

Burst Read Single-bit Write operation

DQM for masking

Auto & self refresh

32ms refresh period (2K cycle)

GENERAL DESCRIPTION

FEATURES

512K x 16Bit x 2 Banks SDRAM

ORDERING INFORMATION

Part NO. MAX Freq. Interface Package

K4S161622H-TC55 183MHz

LVTTL50pin

TSOP(II)K4S161622H-TC60 166MHz

K4S161622H-TC70 143MHz

K4S161622H-TC80 125MHz

Row & Column address configuration

Organization Row Address Column Address

1Mx16 A0~A10 A0-A7

16


19/41


Rev. 1.4 May 2004

VDDDQ0DQ1VSSQDQ2DQ3

VDDQDQ4DQ5VSSQDQ6DQ7

VDDQLDQM

WECAS

RASCSBA

A10/APA0A1A2A3

VDD

12345678910111213141516

171819202122232425

50494847464544434241403938373635

343332313029282726

PIN CONFIGURATION (TOP VIEW)

VSSDQ15DQ14VSSQDQ13DQ12VDDQDQ11DQ10VSSQDQ9DQ8VDDQN.C/RFUUDQMCLK

CKEN.CA9A8A7A6A5A4VSS

50PIN TSOP (II)

(400mil x 825mil)

(0.8 mm PIN PITCH)

PIN FUNCTION DESCRIPTION

Pin Name Input Function

CLK System Clock Active on the positive going edge to sample all inputs.

CS Chip Select

Disables or enables device operation by masking or enabling all inputs except

CLK, CKE and L(U)DQM

CKE Clock Enable

Masks system clock to freeze operation from the next clock cycle.

CKE should be enabled at least one cycle prior to new command.

Disable input buffers for power down in standby.

A0~ A10/AP AddressRow / column addresses are multiplexed on the same pins.

Row address : RA0~ RA10, column address : CA0~ CA7

BA Bank Select AddressSelects bank to be activated during row address latch time.

Selects bank for read/write during column address latch time.

RAS Row Address StrobeLatches row addresses on the positive going edge of the CLK with RAS low.

Enables row access & precharge.

CAS Column Address StrobeLatches column addresses on the positive going edge of the CLK with CAS low.

Enables column access.

WE Write EnableEnables write operation and row precharge.

Latches data in starting from CAS, WE active.

L(U)DQM Data Input/Output MaskMakes data output Hi-Z, tSHZafter the clock and masks the output.

Blocks data input when L(U)DQM active.

DQ0~ 15 Data Input/Output Data inputs/outputs are multiplexed on the same pins.

VDD/VSS Power Supply/Ground Power and ground for the input buffers and the core logic.

VDDQ/VSSQ Data Output Power/GroundIsolated power supply and ground for the output buffers to provide improved noise

immunity.

N.C/RFUNo Connection/

Reserved for Future UseThis pin is recommended to be left No Connection on the device.

17


20/41


Rev. 1.4 May 2004

FUNCTIONAL BLOCK DIAGRAM

* Samsung Electronics reserves the right to change products or specification without notice.

Bank Select

Data Input Register

512K x 16

512K x 16

SenseAMP

OutputBuffer

I/OControl

Column Decoder

Latency & Burst Length

Programming Register

AddressRegister

Row

Buffer

RefreshCounter

Row

Decoder

Col.Buffer

LRAS

LCBR

LCKE

LRAS LCBR LWE LDQM

CLK CKE CS RAS CAS WE L(U)DQM

LWE

LDQM

DQi

CLK

ADD

LCAS LWCBR

Timing Register

18


21/41

MT1389

Prog ress ive-Scan DVD Player SOCSpecifications are subject to change without notice

MediaTek MT1389is a DVD player system-on-chip (SOC) which incorporates advanced features like high

quality TV encoder and state-of-art de-interlace processing. The MT1389 enables consumer electronicsmanufacturers to build high quality, cost-effective DVD players, portable DVD players or any other homeentertainment audio/video devices.

Based on MediaTeks world-leading DVD player SOC architecture, the MT1389 is the 3 rdgeneration of the DVDplayer SOC. It integrates the MediaTek 2ndgeneration front-end analog RF amplifier and the Servo/MPEG AVdecoder.

The progressive scan of the MT1389 utilized a proprietary advanced motion-adaptive de-interlace algorithm toachieve the best movie/video playback. It can easily detect 3:2/2:2 pull down source and restore the correctoriginal pictures. It also supports a patent-pending edge-preserving algorithm to remove the saw-tooth effect.

MT1389L

DVDPUH

Module

FLASH

DRAM

CVBS, Y/C,Component

SDPIF

Front-panelRemote

Audio DAC

DVD Player System Diagram Using MT1389

Key Features RF/Servo/MPEG Integration

High Performance Audio Processor

Motion-Adaptive, Edge-Preserving De-interlace 108MHz/12-bit, 6 CH TV Encoder

Applications Standard DVD Players

Portable DVD Players

8.2 MT1389

19


22/41

MT1389

PRELIMINARY, SUBJECT TO CHANGE WITHOUT NOTICE MTK CONFIDENTIAL, NO DISCLOSURE

General Feature List

Super Integration DVD player single chip

High performance analog RF amplifier Servo controller and data channel processing MPEG-1/MPEG-2/JPEG video Dolby AC-3/DTS/DVD-Audio Unified memory architecture Versatile video scaling & quality

enhancement OSD & Sub-picture 2-D graphic engine Built-in clock generator Built-in high quality TV encoder Built-in progressive video processor Audio effect post-processor Audio input port

High Performance Analog RF Amplifier

Programmable fc Dual automatic laser power control Defect and blank detection RF level signal generator

Speed Performance on Servo/Channel Decoding

DVD-ROM up to 4XS CD-ROM up to 24XS

Channel Data Processor Digital data slicer for small jitter capability Built-in high performance data PLL for

channel data demodulation EFM/EFM+ data demodulation Enhanced channel data frame sync protection

& DVD-ROM sector sync protection

Servo Control and Spindle Motor Control

Programmable frequency error gain andphase error gain of spindle PLL to controlspindle motor on CLV and CAV mode

Built-in ADCs and DACs for digital servocontrol

Provide 2 general PWM Tray control can be PWM output or digital

output

Embedded Micro controller

Built-in 8032 micro controller Built-in internal 373 and 8-bit programmable

lower address port

1024-bytes on-chip RAM Up to 4M bytes FLASH-programming

interface Supports 5/3.3-Volt. FLASH interface Supports power-down mode Supports additional serial port

DVD-ROM/CD-ROM Decoding Logic

High-speed ECC logic capable of correctingone error per each P-codeword orQ-codeword

Automatic sector Mode and Form detection Automatic sector Header verification Decoder Error Notification Interrupt that

signals various decoder errors Provide error correction acceleration

Buffer Memory Controller

Supports 16Mb/32Mb/64Mb/128Mb SDRAM Supports 16-bit SDRAM data bus Provide the self-refresh mode SDRAM Block-based sector addressing Support 3.3 Volt. DRAM Interface

Video Decode

Decodes MPEG1 video and MPEG2 main level,main profile video (720/480 and 720x576)

Smooth digest view function with I, P and Bpicture decoding

Baseline, extended-sequential andprogressive JPEG image decoding

Support CD-G titles

Video/OSD/SPU/HLI Processor

Arbitrary ratio vertical/horizontal scaling ofvideo, from 0.25X to 256X

65535/256/16/4/2-color bitmap format OSD, 256/16 color RLC format OSD Automatic scrolling of OSD image Slide show transition as DVD-Audio

Specification

2-D Graphic Engine

Support decode Text and Bitmap Support line, rectangle and gradient fill Support bitblt Chroma key copy operation Clip mask

20


23/41

MT1389

PRELIMINARY, SUBJECT TO CHANGE WITHOUT NOTICE MTK CONFIDENTIAL, NO DISCLOSURE

Audio Effect Processing

Dolby Digital (AC-3)/EX decoding DTS/DTS-ES decoding MLP decoding for DVD-Audio

MPEG-1 layer 1/layer 2 audio decoding MPEG-2 layer1/layer2 2-channel audio High Definition Compatible Digital (HDCD) Windows Media Audio (WMA) Advanced Audio Coding (AAC) Dolby ProLogic II Concurrent multi-channel and downmix out IEC 60958/61937 output

- PCM / bit stream / mute mode- Custom IEC latency up to 2 frames

Pink noise and white noise generator Karaoke functions

- Microphone echo- Microphone tone control- Vocal mute/vocal assistant- Key shift up to +/- 8 keys- Chorus/Flanger/Harmony/Reverb

Channel equalizer 3D surround processing include virtual

surround and speaker separation

TV Encoder

Six 108MHz/12bit DACs Support NTSC, PAL-BDGHINM, PAL-60 Support 525p, 625p progressive TV format

Automatically turn off unconnected channels Support PC monitor (VGA) Support Macrovision 7.1 L1, Macrovision

525P and 625P CGMS-A/WSS Closed Caption

Progressive Output

Automatic detect film or video source 3:2 pull down source detection Advanced Motion adaptive de-interlace Edge Preserving

Minimum external memory requirement

Audio Input

Line-in/SPDIF-in for versatile audioprocessing

Outline

256-pin LQFP package 3.3/1.8-Volt. Dual operating voltages

21


24/41

C402

104

C401

104

1 23

U402

HS0038B

K403

K401

K402

VD401

1N4

148

KEY3

KEY2

KEY1

S1

LEDST

LEDCK

LEDAT

VCC

GND

C403

104

IR

R401

51K

R404

10K

R402

10K

R403

10K

TC402

100u

F/16V

IR

OSC

1

DOUT

2

DIN

3

CLK

4

STB

5

K1

6

K2

7

K3

8

VDD

9

NC

13

SEG1/KS1

10

SEG2/KS2

11

SEG3/KS3

12

SEG4/KS4

14

SEG5/KS5

15

G

R6

23

SEG6/KS6

16

SEG7/K

S7

17

SEG8/K

S8

18

SEG9/K

S9

19

SEG10/KS

10

20

SEG

11

21

SEG12/G

R7

22

VDD

25

GND

26

G

R5

24

G

R4

27

G

R3

28

GND

29

G

R2

30

G

R1

31

GND

32

U401

PT6961

LEDAT

LEDCK

LEDST

KEY1

KEY2

KEY3

S1

S2

S3

S4

S5

S7

S10

G9

G8

G12

G6

VCC

VCC

VCC

TC403

100u

F/16V

S11

R405

100R

TC404

100u

F/16V

VCC

G

1

G

2

G

3

G

4

G

5

S6

G7

S8

S9

G10

G11

S12

5 4 3 2 1

12

11

10987

6

LED-4

01

LED-S

OCK(1)

C404

R407

R408

R4

06

TC

401O

K

L401

32

1

VR401

IN

VR2

VR1

2 3 41 5 6 7 8 910

11

XS401

XS11

OK

INVR1

VR2

DET

5 4 3 2 17 6

MIC401

1 2R409

4.7

K

VCC

DET

FRONT SCHEMATIC DIAGRAM

22

9. SCHEMATIC & PCB WIRING DIAGRAM


25/41

RONT SCHEMATIC DIAGRAM

23


26/41

U503

LM431A

C515

104

L505

10u

H/1A

C506

473

L507

10u

H/2A

BC

501

~275V104

L501

F501

T1.6A

/250V

R

K A

!

!

!

R509

10K

R508

3.3

K

R506

330

R505

10o

hm

R503

39K/2W

!

BCN502

SW-S

PST

!

!

U502

2501

TC502

47uF

/50V

TC501

47u

F/400V

D505

HER107

C502

103/1KV

C503

101/1KV

L503

FB

BC503

~400V221

+9V

C504

104

TC504

470u

F/16V

TC512

47u

F/50V

TC506

1000u

F/10V

TC505

1000u

F/10V

TC510

1000uF

/10V

D508

HER105

TC503

470u

F/16V

R511

330R/1W

R507

1K

R501

680K2W

!

! !

D510

SR560

D506

HER105

D509

1N4007

D511

HER105

+3

.3V T

C513

100u

F/16V

D503

1N4007

A 1

K2

D502

1N4007

D504

1N4007

D501

1N4007

C508

104

C510

104

-9V

+5V

ZD502

9.1

V/1W

VDD

4

D5

S 2

FB

3

D6

D7

D8

S 1

U5

01

VIPER22

R512

9.1

K

D513

1N4007

1

2

3

4

5

6

7

8

9

10

T501

EEL19H

-9V

GND

+3

.3V

+5V

GND

+9V

GND

2 3 41 5 6 7

CN502

XS07

21

CN501

XS02

LED+5V

12

BCN501

~220V

D507

HER105

TC507

1000

uF/10V

LED+5V

POWER BOARD SCHEMATIC DIAGRAM

24


27/41

POWER BOARD SCHEMATIC DIAGRAM

25


28/41

R61415K

R61710K

R6165.6K

R626

1K

C610

561

C612

561

C613

104

C614

104

C615

392

R621

10K

R6224.7K

R624

10K

R619

1K

R

612

1

0K

32

1

84

U601A

4558

+9VA

32

1

84

U602A

4558

C607

101

R613

30K

56

7

U602B

4558

C620

101

R609

30K

C605

101

R610

30K

C609

104

TC608

22uF

/16V

R615

10K

TC607

4.7

uF/16V

R607

1K

R608

20K

R618

15KC

608

392

TC609

47u

F/16V

R629

27K

1

2TC605

22U/16V

TC603

4.7

U/16V

-9VA

C619

102

R628

4.7

K

R62010K

R633

10R1/6W

TC615

100U/16V

C601

104

R632

10R1/6W

TC616

100U/16V

C602

104

+9V

+9VA

-9V

-9VA

C622

104

C623

104

OKA

TC610

4.7

uF/16V

TC613

4.7

U/16V

VDD 1

REF 2

AGND 3

DGND 4

CLKO 5

VCO 6

CC1 7

CC2 8

OP1-OUT9

OP1-IN10

OP2-IN11

OP2-OUT12

LPF2-IN13

LPF2-OUT14

LPF1-OUT15

LPF1-IN16

U603

PT2399

TC611

4.7

U/16V

+9VA

TC621 4

.7uF

/16V

C616

103

+5V

-9VA

IN

VR1

VR2

GND

OKA

IN VR1

VR2

+5V

DET

2 3 41 5 6 7

XS601

OKA

2 3 41 5 6

XS602

XS06

DET

+9V

-9V

+5V

GND

OK SCHEMATIC DIAGRAM

26


29/41

OK SCHEMATIC DIAGRAM

27


30/41

AGND

AGNDVGND

LFE

CC

SR

SL

RLVIEDO

Pb

Y1

Pr

PDAT1

PDAT2

VCC

SPDIF

L R

RED

WHITE

L705

FB

L706

FB

C705

102

C706

102

2 3 41 5 6 8 9 10

7 11

12

14

15

16

13

17

18

20

21

22

19

23

24

25

26

28

27

XS701

XS28

Y C

A(B)OUT

1

A(A)OUT

3

RETURN

5

BLUEI/O

7

RETURN

9

GREENI/O

11

RETURN

13

REDI/O

15

RETURN

17

V-O

UT

19

GND

21

A(B)IN

2

A-C

OM

4

A(A)IN

6

FUNCSW

8

CONT

10

NC

12

RETURN

14

BLKI/O

16

TRTURN

18

V-I

N

20

JK706

VJS3921

R704

4.7

K

R705

75R

V701

8050

V702

8050

R708

33R

R709

330R

R710

2.2

K

+10V

A+10V

AGND

PDAT0

V703

8050

R711

1K

R712

2.2

K

A+10V

PDAT2

C716

104

AGND

VCC

AGND

R70

7

A+10V

AGND

AGND

VCC

PDAT0

+10V

VGND

VGND

Pr

L709

FBSMT

L708

FBSMT

L707

FBSMT

Y1

Pb

VGND

GREEN

BLUE

RED

BG R

1

2

3 4

5

6JK702

RCA-4

07

BLACK

TC702

1000uF

/10V

TC703

220uF

/16V

TC704

220uF

/16V

L710

FBSMT

SPDIF

R701

22

0R

C710104

L713

FCM

L714

FCM

C707

105

VGND

R713

0R

AGND

VGND

R703

68R

VIN

1

VCC

2

GND

3JK705

OPTICAL

VCC

VGND

C71

1

104

SPDIF

L712

FBSMT

L711

FBSMT

43

2 1

JK703A

S-V

IDEO

5

7

6

JK703B

V-OU

T5

R706

2.2

R

TC701220u

F

R702

10

0R

VIEDO

TC705

220uF

/16V

TC706

220uF

/16V

Y C

C715

224

VGND

VGND

1

2

3JK701

AV8-2

R717

0R

R718

0R

R7190R

R7140R

R7150R

R716

0R

OUTPUT BOARD SCHEMATIC DIAGRAM

28


31/41

OUTPUT BOARD SCHEMATIC DIAGRAM

29


32/41


33/41


34/41

R2105

330R

R2108

10K

+9V

R2109

150R

R2104

1K

VD205

1N4148

+9V

R2103

1K

AGND

VD206

1N4148

-9V

AGND

MUTE-1

TC235

220uF

/16V

TC234

47uF

/16V

AGND

R2106

10K

Q212

2SC1815-Y

Q218

1015

Q219

1015

C2134

683(DNS)

C2131

0R

C2132

683(DNS)

SW /C

SR#

SL#

R L

TC225

10uF

/16V

TC226

10uF

/16V

TC227

10u

F/16V

TC228

10u

F/16V

TC229

10u

F/16V

TC230

10u

F/16V

R2

150

4.7

K

R2151

4.7

K

C2128

0R

C2127

102

C2126

101R

2149

20K

R214120K

C2120

101

C2121

102

C2137

683(DNS)

R2143

4.7

K

R2142

4.7

K

R2138

4.7

K

R2139

4.7

K

C2119

0R

C2118

102

C2117

101

R2137

20K

R2

146

4.7

K

R2147

4.7

KC2124

102

C2123

101

R2145

20K

R2134

4.7

K

R2135

4.7

KC2115

102

C2114

101

R2133

20K

R2129

20K

C2111

101

C2112

102

R2131

4.7

K

R2130

4.7

K

+9V

+9V

+9V

+9V

+9V +

9V

32

1

48

U219A

4580 56

7

48

U219B

4580

32

1

48

U221A

458056

7

48

U220B

4580

32

1

48

U220A

4580

56

7

48

U221B

4580

AGNDA

GND

AGND

AGND

AGND

AGND

-9V

-9V

-9V

-9V

-9V -

9V

TC224

10u

F/16V

TC223

10u

F/16V

TC222

10u

F/16V

TC221

10u

F/16V

TC240

10u

F/16V

TC241

10u

F/16V

CH-L

CH-R

CH-S

L

CH-S

R

CH-C

CH-S

W

AGND

R2123

1KR2121

1KR2120

1KR2117

1K R2124

1KR2122

1KR2119

1KR2118

1K

R2111

100K

R2112

100K

R2113

100K

R2114

100K

MUTE-1

Q208

2SC1815-Y

S

Q207

2SC1815-Y

S

Q205

2SC1815-Y

S

Q206

2SC1815-Y

SR2127

1K

R2125

1K

R2128

1K

R2126

1K

R2115

100K

R2116

100K

Q210

2SC1815-Y

S

Q209

2SC1815-Y

S

C2138

104

C2139

104

C2140

104

+9V

AGND C

2141

104

C2142

104

C2143

104

-9V

AGND

SDATA2

SDATA1

SDATA0

SLRCK

SACLK

SBCLK

SCL

SDA

RESET#

LL

RS

RR

LS

LFE#

C#

R2132

20K

C2116

102O

KA

AGND

R2156

20K

R2136

6.8

K

R2148

6.8

K

R21526

.8K

R21536

.8K

R21546

.8K

R21556

.8K

C2122

122

C2129

122

C2130

122

C2133

122

C2135

122

C2136

122

VOICE-D

ET

VLS

1

SDIN1

2

SDIN2

3

SDIN3

4

SCLK

5

LRCK

6

MCLK

7

VD

8

GND

9

RST

10

SCL

11

SDA

12

CS

13

VLC

14

MUTEC1

28

AOUTA1

27

AOUTB1

26

MUTEC2

25

AOUTA2

24

AOUTB2

23

VA

22

GND

21

AOUTA3

20

AOUTB3

19

MUTEC3

18

VQ

17

FILT+

16

M2

15

U207

CS4360

C2154

104

C2153

104

DV33

MUTE1

C2155

104

TC236

10uF

/16V

AVCC

C2157

104

TC232

10uF

/16V

C2156

104

TC233

10uF

/16V

AGND

R282

0R

TC231

10uF

/16V

MUTE2

MUTE3

RR

RS

LL

LS

LFE#

C#

MUTE1

Q211

1015

R2102

1KR

2101

1K

VD207

1N4148

VD208

1N4148

VD209

1N4148

MUTE2

MUTE3

TC238

2.2

uF/16V

(DNS)

VCC

R225

0R(DNS)

R226

0R

AVCC

R291

33R

ACLK

SACLK

R292

33R

R293

33R

R294

33R

R295

33R

R296

33R

ABCK

SBCLK

ALRCK

SLRCK

ASDAT0

SDATA0

SDATA1

SDATA2

ASDAT1

ASDAT2

R2107

0R

AGND

Cc

LFE

SL

AGND

SRR

tLt

MUTEA

VL

1

MCLK

2

SCLK

3

SDATA

4

VA

5

GND

6

LRCK

7

DIN

8

RST

16

VQ

15

AINL

14

AINR

13

REF

_G

12

FILT+

11

TST

10

DIF

9

U210

CS5333(16)

C287

104

C284

104

DV33

SACLK

SBCLK

AMDAT

SLRCK

R289

47K

C286

105

C288

102

TC242

1u

F/16V

TC243

1u

F/16V

R2180

150R

RESET#

OKA

TC244

10u

F/16V

DV33

C285

105

R279

0R(DNS)

R268

0R(DNS)

R269

0R(DNS)

R278

0R(DNS)

DV33

R288

4.7K

RST

1

SDA

2

SCLK

3

LRCK

4

MCLK

5

DIF1

6

DIF0

7

DEM0

8

MUTEC

16

AOUTA

15

VA

14

AGND

13

AOUTB

12

REF-G

ND

11

VQ

10

FILT+

9

U206

CS4340

R284

0R

R285

0R

R286

0R

RESET#

SDATA0

SBCLK

SLRCK

SACLK

MUTE1

LL

AVCC

AGND

RR

AGND

VQ#

FILT+

VQ#

FILT+

MIAN SCHEMATIC DIAGRAM

32


35/41

MIAN SCHEMATIC DIAGRAM

33


36/41

DV314SMATERIAL LIST

1. MAIN FRONT PANEL

MATERIAL CODE MATERIAL NAME SPECIFICATIONS UNIT QUANTITY LOCATION

5233123 SOFT SPONGE SPACER 101013 DOUBLE-FACED, HARD PCS 1 1PC FOR IR SENSOR

5233021 SOFT SPONGE SPACER 13813.5 DOUBLE-FACED, HARD PCS 2 2PCS FOR LED AND

FRONT PANEL PCB

1340064 LIGHT TOUCH

RESTORE SWITCH KFC-A06-2WB L3.8 PCS 3 K401~K403

0260241 CD CD11C 16V4.7U20%47 1.5 PCS 1 TC401

0260206 CD CD11C 10V100U20%57 2 PCS 3 TC402,TC403,TC404

1200574 DISPLAY SCREEN TOF-2482AG-B18 PCS 1 LED401

2360024 IR SENSOR LTOP-4338 PCS 1 U402

2360002 IR SENSOR HS0038B PCS 1 U402

2360006 IR SENSOR 9052-4 PCS 1 U402

0881426 IC PT6961 SOP PCS 1 U401

1980048 MICROPHONE SOCKET ST-403-070-100 PCS 1 MIC401

0160184 ROTATED

POTENTIOMETER WH09JTC1Z11-A10K-F30 PCS 1 VR401

2121525 FLAT CABLE

12-6/6P150/100 2.0 T3 WITH L

NEEDLE REVERSE PCS 1 XS401

0090181 SMD RESISTOR 1/16W 1005% 0603 PCS 1 R405

0090192 SMD RESISTOR 1/16W 51K 5% 0603 PCS 1 R401

0090023 SMD RESISTOR 1/16W 10K 5% 0603 PCS 4 R402,R403,R404,R407

0090019 SMD RESISTOR 1/16W 4.7K 5% 0603 PCS 1 R409



0310084 SMD CAPACITOR 50V 104 +80%-20% 0603 PCS 3 C401,C402,C403

0310072 SMD CAPACITOR 50V 103 10% 0603 PCS 1 C404

0390095 SMD MAGNETIC BEADS FCM1608K-221T05 PCS 2 L401,L402

0700007 SMD DIODE 1N4148 PCS 1 VD401

1631681 PCB 4703A-1 PCS 1

2. POWER BOARD


0000294 CARBON FILM

RESISTOR 1/4W10K5% SHAPED 10 PCS 1 R507

0010256 METAL FILM RESISTOR 1/4W3.6K1% SHAPED 10 PCS 1 R508

0000461 CARBON FILM

RESISTOR

1/4W9.1K5% SHAPED 10 PCS 1 R512

0010064 METAL FILM RESISTOR 1/4W10K1% SHAPED 10 PCS 1 R509

0000431 CARBON FILM

RESISTOR 1/4W75 5% SHAPED 10 PCS 1 R505

0010135 METAL OXIDE FILM

RESISTOR 2W39K5% SHAPED FLAT 159 PCS 1 R503

0580054 VOLTAGE REGULATOR

DIODE 9.1V 1W PCS 1 ZD502

0010250 METAL OXIDE FILM

RESISTOR 1W22

5

SHAPED R 158 PCS 1 R511

0000380 CARBON FILM


0070001 HIGH VOLTAGERESISTOR

1/2W680K5% PCS 1 R501

0570005 DIODE 1N4007 PCS 4 D501~D504

0200138 PORCELAIN

CAPACITOR 50V 104 20% 5mm PCS 4 C504,C508,C510,C515

0200224 PORCELAIN

CAPACITOR 1000V 103 +80%-20% 7.5mm PCS 1 C502

34

10. SPARE PARTS LIST


37/41

0200223 PORCELAIN

CAPACITOR 1000V 101 +80%-20% 7.5mm PCS 1 C503

0200228 PORCELAIN

CAPACITOR 1000V 101 10% 7.5mm PCS 1 C503

0210049 TERYLENE CAPACITOR 50V 473 10% 6mm PCS 1 C506

0260559 CD CD11T 50V47u20%612 2.5 PCS 2 TC502,TC512

0260563 CD KM 400V47U20%1820 7.5 PCS 1 TC501

0260557 CD CD11T 16V100u20%612 2.5 PCS 1 TC513

0260594 CD CD11T 25V220U20%812 3.5 PCS 2 TC503,TC504

0260560 CD CD11T 10V1000u20%816 3.5 PCS 3 TC505,TC506,TC510

0390057 MAGNETIC BEADS

INDUCTOR RH354708 PCS 1 L503

0410010 CHOKE COIL VERTICAL 10UH 1A 5mm PCS 1 L505

0410011 CHOKE COIL VERTICAL 10UH 2A 5mm PCS 1 L507

1080011 PHOTOELECTRIC

COUPLER HS817 PCS 1 U502

1080006 PHOTOELECTRIC

COUPLER PC817 PCS 1 U502

0570011 DIODE RL202 PCS 2 D513,D509

0570013 DIODE HER105 PCS 3 D506,D508,D511

0570014 DIODE HER107 PCS 1 D505

0680010 SCHOTTKY DIODE SR560 DO-27 PCS 1 D510

0880553 IC LM431ACZ TO-92 PCS 1 U503

0880581 IC TL431C TO-226AA(LP) PCS 1 U503

0880800 IC 431L TO-92 PCS 1 U503

0882041 IC MIK431C TO-92 PCS 1 U503

0210066 TERYLENE CAPACITOR 275V 104 20% 15mm PCS 1 BC501

0210070 TERYLENE CAPACITOR 275V 104 10% 15mm PCS 1 BC501

0200267 CERAMIC CAPACITOR CT81 250VAC22120% 10mm PCS 1 BC503

0200268 CERAMIC CAPACITOR CT81 250VAC22110% 10mm PCS 1 BC503

0460394 SWITCHING POWER

TRANSFORMER BCK-19-0179 PCS 1 T501

1000004 POWER GRID FILTER UT-20 40mH 20% 1013 PCS 1 L501

1563407 PCB 5501A-4 PCS 1

2100003 CONNECTION CORDS 0.6 SHAPED 7.5mm PCS 2 JP501,JP503

2100010 CONNECTION CORDS 0.6 SHAPED 5mm PCS 1 JP502

2100004 CONNECTION CORDS 0.6 SHAPED 10mm PCS 1 R517

2300021 FUSE T1.6AL 250V PCS 1 F501

1940045 SOCKET 2P 8.0mm 2# PCS 2 BCN501,BCN502

1940023 SOCKET 7P 2.0mm PCS 1 CN502

1940022 SOCKET 4P 2.0mm PCS 1 CN501

0881933 IC VIPER22A DIP8 PCS 1 U501

3870115 GROUND CHIP OF

POWER BOARD AB903 PCS 2 G501,G502

3. OK BOARD


0000129 CARBON FILM

RESISTOR 1/6W1K5% SHAPED 7.5 PCS 3 R607,R619,R626

0000133 CARBON FILM

RESISTOR 1/6W4.7K5% SHAPED 7.5 PCS 2 R622,R628

0000134 CARBON FILM

RESISTOR 1/6W5.1K5% SHAPED 7.5 PCS 1 R616

0000137 CARBON FILM

RESISTOR 1/6W10K5% SHAPED 7.5 PCS 5

R617,R621,R620,R624,R6

12

35


38/41

0000118 CARBON FILM

RESISTOR 1/6W10

5% SHAPED 7.5 PCS 2 R632,R633

0000338 CARBON FILM

RESISTOR 1/6W15K5% SHAPED 7.5 PCS 2 R614,R618

0000341 CARBON FILM

RESISTOR 1/6W18K5% SHAPED 7.5 PCS 1 R615

0000144 CARBON FILM


0000141 CARBON FILM


0000142 CARBON FILMRESISTOR

1/6W33K5% SHAPED 7.5 PCS 2 R609,R613

0000339 CARBON FILM

RESISTOR 1/6W3.3K5% SHAPED 7.5 PCS 1 R610

0260127 CD CD11 16V4.7U20%511 2 PCS 6

TC603,TC607,TC610,TC6

11,

TC613,TC621

0260021 CD CD11 16V22U20%511 2 PCS 1 TC605

0260258 CD CD11 10V47U20%57 2 PCS 1 TC609

0260200 CD CD11C 16V47U20%57 2 PCS 1 TC609

0260040 CD CD11 25V100U20%612 2.5 PCS 3 TC608,TC615,TC616

0200106 PORCELAINCAPACITOR

50V 101 +80%-20% 5mm PCS 3 C607,C605,C620

0200125 PORCELAIN

CAPACITOR 50V 102 +80%-20% 5mm PCS 1 C619

0200206 PORCELAIN

CAPACITOR 50V 103 +80%-20% 5mm PCS 1 C616

0200139 PORCELAIN

CAPACITOR 50V 104 +80%-20% 5mm PCS 7

C601,C602,C622,C609,C6

13,C614,C623

0200153 PORCELAIN

CAPACITOR 50V 392 20% 5mm PCS 2 C608,C615

0200117 PORCELAIN

CAPACITOR 50V 561 +80%-20% 5mm PCS 2 C610,C612

0880124 IC NJM4558D DIP PCS 2 U601,U602

1940005 SOCKET 6P 2.0mm PCS 1 XS601


2100003 CONNECTION CORDS

0.6 SHAPED 7.5mm PCS 7 JP601~JP607

1563408 PCB 6962S-3 PCS 1

0880230 IC PT2399 DIP PCS 1 U603

4. AV BOARD


0000171

CARBON FILM

RESISTOR 1/4W685% PCS 1 R703

0000362 CARBON FILM

RESISTOR 1/4W220

5% SHAPED 10 PCS 1 R701

0000278 CARBON FILM


0000273 CARBON FILM

RESISTOR 1/4W33


0000276 CARBON FILM


0000268 CARBON FILM

RESISTOR 1/4W2.2


0000289

CARBON FILM

RESISTOR 1/4W4.7K5% SHAPED 10 PCS 1 R704

0000283 CARBON FILM

RESISTOR 1/4W1K5% SHAPED 10 PCS 1 R711

0000286 CARBON FILM

RESISTOR 1/4W2.2K5% SHAPED 10 PCS 2 R710,R712

0000431 CARBON FILM

RESISTOR 1/4W75


36


39/41

0200125 PORCELAIN

CAPACITOR 50V 102 +80%-20% 5mm PCS 2 C705,C706

0200139 PORCELAIN

CAPACITOR 50V 104 +80%-20% 5mm PCS 4 C707,C710,C711,C716

0200237 PORCELAIN

CAPACITOR 50V 224 10% 5mm PCS 1 C715

0200298 PORCELAIN

CAPACITOR 50V 22420% 5mm PCS 1 C715

0090001 SMD RESISTOR 1/16W 05% 0603 PCS 6 R714~R719

0780050 TRIODE S8050D PCS 3 V701~V703


INDUCTOR RH354708 PCS 10 L713,L714,L705~L712

1090045 ELECTRO-OPTIC

TRANSFORMER TX179ATW PCS 1 JK705

1090024 ELECTRO-OPTIC

TRANSFORMER TX179AT PCS 1 JK705

1910078 TERMINAL SOCKET AV4-8.4-6G-3 PCS 1 JK702

1910129 TERMINAL SOCKET SA-001-012 BLACK IRON SHEET

SCREEN-SHIELDED PCS 1 JK703

1910062 TERMINAL SOCKET AV2-8.4--6G PCS 1 JK701

1940140 CABLE SOCKET 14P 1.0mm STRAIGHT DUAL LINE

PLUG

PCS 1 XS701

2100004 CONNECTION CORDS

0.6 SHAPED 10mm PCS 12 J P701~JP711,R707

1860029 SCART SOCKET SCART-01 PCS 1 JK706

1563282 PCB 7962S-2 PCS 1

5. DECODE BOARD


0090001 SMD RESISTOR 1/16W 05% 0603 PCS 36

L210~L215,R201~R204,R

212,R228,R234,R236,R24

5,R247,R222,R251,R255,

R257,R258,R298,R299,R3

03,R318,R331,R2159,R29

7,R284~R286,R287,R290,

R2183,R2107,R283

0090006 SMD RESISTOR 1/16W 755% 0603 PCS 7 R233,R261,R270,R273,R2

74,R276,R280

0100034 SMD RESISTOR

NETWORKS 1/16W05% 06034 8P PCS 4 RN201~RN204

0000375 CARBON FILM

RESISTOR 1/4W2.25% PCS 1 R326

0090272 SMD RESISTOR 1/16W15% 0603 PCS 6 R304~R307,R321,R340

0090003 SMD RESISTOR 1/16W 105% 0603 PCS 2 R301,R302

0090005 SMD RESISTOR 1/16W 335% 0603 PCS 14

R231,R232,R256,R263~R

267,R291~R294,R2162,L2

02


0090009 SMD RESISTOR 1/16W 3305% 0603 PCS 4 R2105,R221,R277,R281



0090014 SMD RESISTOR 1/16W 1K 5% 0603 PCS 11 R213,R215,R2101~R2104,

R2117~R2120,R254

0090016 SMD RESISTOR 1/16W 1.5K 5% 0603 PCS 3 R323,R324,R243


0090018 SMD RESISTOR 1/16W 3.3K 5% 0603 PCS 1 R242

0090019 SMD RESISTOR 1/16W 4.7K 5% 0603 PCS 8 R238~R240,R2130,R2131,

R2134,R2135,R2140

37


40/41

0090021 SMD RESISTOR 1/16W 6.8K 5% 0603 PCS 2 R2136,R2148

0090023 SMD RESISTOR 1/16W 10K 5% 0603 PCS 12

R208,R229,R252,R309,R3

11,R313,R314,R329,R330,

R339,R2164,R2106

0090024 SMD RESISTOR 1/16W 15K 5% 0603 PCS 2 R209,R223

0090025 SMD RESISTOR 1/16W 20K 5% 0603 PCS 6 R211,R312,R315,R316,R2

129,R2133

0090255 SMD RESISTOR 1/16W24K5% 0603 PCS 2 R2132,R2156


0090197 SMD RESISTOR 1/16W 150K 5% 0603 PCS 2 R319,R320

0090231 PRECISION SMD

RESISTOR 1/16W 680K 1% 0603 PCS 2 R317,R322

0090319 PRECISION SMD

RESISTOR 1/16W 750K 1% 0603 PCS 1 R227

0090034 SMD RESISTOR 1/16W 100K 5% 0603 PCS 6 R224,R308,R310,R2111,R

2112,R246

0260019 CD CD11 16V10U20%511 2 PCS 10

TC201,TC202,TC217,TC2

32,TC233,TC236,TC240,

TC241,TC225,TC226

0260028 CD CD11 16V220U20%612 2.5 PCS 8 TC207~TC209,TC211,TC

213,TC235,TC245,TC301

0260025 CD CD11 16V47U20%511 2 PCS 14

TC204~TC206,TC210,TC234,TC237,TC302~TC304

,TC308,TC309,TC247,TC

248,TC246

0310085 SMD CAPACITOR 50V 20P 5% NPO 0603 PCS 2 C222,C232

0310190 SMD CAPACITOR 50V 27P 5% NPO 0603 PCS 2 C275,C276

0310045 SMD CAPACITOR 50V 47P 5% NPO 0603 PCS 17

C262~C265,C266,C289,C

290,C292,C293,C295,C29

6,C298,C299,C2101,C210

2,C2104,C2105

0310047 SMD CAPACITOR 50V 101 5% NPO 0603 PCS 4 C233,C2111,C2114,C206

0310051 SMD CAPACITOR 50V 331 5% NPO 0603 PCS 2 C212,C213

0310048 SMD CAPACITOR 50V 151 5% NPO 0603 PCS 2 C304,C306

0310084 SMD CAPACITOR 50V 104 +80%-20% 0603 PCS 77

C207,C211,C214,C216,C2

17,C224,C226~C231,C234

~C239,C241~C254,C256~

C259,C267~C274,C279,C

280~C282,C301~C303,C3

05,C309,C311,C312,C213

8~C2143,C2155~C2157,C

2160,C2161,C2163,C2164,

C2168,C2169,C2166,C217

0~C2175

0310058 SMD CAPACITOR 25V 104 +80%-20% 0603 PCS 77

C207,C211,C214,C216,C2

17,C224,C226~C231,C234

~C239,C241~C254,C256~

C259,C267~C274,C279,C

280~C282,C301~C303,C3

05,C309,C311,C312,C213

8~C2143,C2155~C2157,C

2160,C2161,C2163,C2164,

C2168,C2169,C2166,C217

0~C2175

0310234 SMD CAPACITOR 16V 105 +80%-20% 0603 PCS 6 C201~C204,C221,C240

0310066 SMD CAPACITOR 50V 102 10% 0603 PCS 9C2112,C2115,C223,C278,C255,C291,C294,C297,C2

116

0310231 SMD CAPACITOR 50V 122 10% 0603 PCS 2 C2122,C2129



38


41/41




0310362 SMD CAPACITOR 16V474 +80%-20% 0603 PCS 1 C218

0390044 SMD INDUCTOR 10UH 10% 2012 PCS 2 L303,L306

0390096 SMD INDUCTOR 1.8UH 10% 1608 PCS 6 L243~L248


INDUCTOR RH354708 PCS 11

L205,L217,L220,L221,L2

22,L223,L227,L228,L226,

L302,l239

0390095 SMD MAGNETIC BEADS FCM1608K-221T05 PCS 35

, , ~ ,

34~L236,L238,L250,L309,

L229~L233,L301,L304,L3

05,L307,L308,L310~L312,

L314,L316~L324

0090106 SMD RESISTOR 1/16W 4.75% 0603 PCS 1 L206

0700007 SMD DIODE 1N4148 PCS 16 VD201,VD205~VD207,VD

210~VD221

0700001 SMD DIODE LS4148 PCS 16 VD201,VD205~VD207,VD

210~VD221

0700002 SMD DIODE LL4148 PCS 16 VD201,VD205~VD207,VD

210~VD2210780029 TRIODE C8050 PCS 2 V307,V308

0780030 TRIODE 8550C PCS 2 V306,V309

0780062 SMD TRIODE 9014C PCS 1 V310

0780033 TRIODE 9015C PCS 1 Q204

0780020 TRIODE C1815Y PCS 1 Q212

0780197 SMD TRIODE C1815 PCS 2 Q205,Q206

0780043 TRIODE 2SA1015 PCS 3 Q211,Q218,Q219

0780040 SMD TRIODE 3904 PCS 1 V305

0780193 SMD TRIODE 2SK3018 PCS 2 V303,V304

0780115 SMD TRIODE 2SB1132 PCS 2 V301,V302

0880185 IC NJM4558M SOP PCS 1 U219

0880562 IC 4580 SOP PCS 1 U219

0880361 IC 4558 SOP PCS 1 U219

0880322 IC MM74HCU04M SOP PCS 1 U205

0880513 IC HCU04 SOP PCS 1 U205

0881275 IC IC42S16100-7T SOP PCS 2 U203,U204

0881182 IC LM1117MP-ADJ SOT-223 PCS 1 U209

0881124 IC CS4340-KS SOP PCS 1 U206

0881031 IC 24C02N SOP PCS 1 U202

0882257 IC MT1389FE/C(C VERSION) QFP PCS 1 U201

0881378 IC BA5954FP HSOP PCS 1 U302

0960020 CRYSTAL OSCILLATOR 27.00MHz 49-S PCS 1 X201

1940140 CABLE SOCKET 14P 1.0mm STRAIGHT DUAL LINE

PLUG PCS 1 XS204

1631889 PCB 2967B-3 PCS 1


1940005 SOCKET 6P 2.0mm PCS 2 XS303,XS201

1940030 SOCKET 10P 2.5mm PCS 1 XS203

Documents

DVD BBK Dv314s 1389 Service Manual