REV. 0Information furnished by Analog Devices is believed to be accurate andreliable. However, no responsibility is assumed by Analog Devices for itsuse, nor for any infringements of patents or other rights of third partieswhichmayresultfromitsuse.Nolicenseisgrantedbyimplicationorotherwise under any patent or patent rights of Analog Devices.aAD6600One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106,U.S.A.Tel: 781/329-4700 World Wide Web Site: http://www.analog.comFax: 781/326-8703 Analog Devices, Inc., 2000FUNCTIONAL BLOCK DIAGRAMFEATURESDual IF Inputs, 70 MHz250 MHzDiversity or Two Independent IF SignalsSeparate Attenuation PathsOversample RF Channels20 MSPS on a Single Carrier10 MSPS/Channel in Diversity ModeTotal Signal Range 90+ dB30 dB from Automatic Gain-Ranging (AGC)60 dB from A/D ConverterRange >100 dB After Processing GainDigital Outputs11-Bit ADC Word3-Bit RSSI Word2 Clock, A/B IndicatorSingle 5 V Power SupplyOutput DVCC 3.3 V or 5 V775 mW Power DissipationAPPLICATIONSCommunications ReceiversPCS/Cellular Base StationsGSM, CDMA, TDMAWireless Local Loop, Fixed AccessPRODUCT DESCRIPTIONThe AD6600 mixed-signal receiver chip directly samples signalsat analog input frequencies up to 250 MHz. The device includestwo input channels, each with 1 GHz input amplifiers and30 dB of automatic gain-ranging circuitry. Both channels aresampled with a 450 MHz track-and-hold followed by an 11-bit,20 MSPS analog-to-digital converter. Digital RSSI outputs, anA/B channel indicator, a 2 Clock output, references, and con-trol circuitry are all on-chip. Digital output signals are twoscomplement, CMOS-compatible and interface directly to3.3 V or 5 V digital processing chips.The primary use for the dual analog input structure is samplingboth antennas in a two-antenna diversity receiver. However,Channels A and B may also be used to sample two independentIF signals. Diversity, or dual-channel mode, is limited to 10 MSPSper channel. In single-channel mode, the full clock rate of20 MSPS may be applied to a single carrier.The AD6600 may be used as a stand-alone sampling chip, or itmay be combined with the AD6620 Digital Receive Signal Pro-cessor. The AD6620 provides 10 dB25 dB of additional pro-cessing gain before passing data to a fixed- or floating-point DSP.Driving the AD6600 is simplified by using the AD6630 differen-tial IF amplifier. The AD6630 is easily matched to inexpensiveSAW filters from 70 MHz to 250 MHz.Designed specifically for cellular/PCS receivers, the AD6600supports GSM, IS-136, CDMA and Wireless LANs, as well asproprietary air interfaces used in WLL/fixed-access systems.Units are available in plastic, surface-mount packages (44-leadLQFP) and specified over the industrial temperature range(40C to +85C).Dual Channel, Gain-RangingADC with RSSIGAINA/DCONVERTERTIMINGENCODESELECT GAIN+12, +18dBENCODEFLT FLTNOISE FILTERRESONANTPORT630RSSI3TWO'SCOMPLEMENT11AB_OUTD10D0RSSI [2:0]CLK2DVCC ENC ENC GND AVCC B_SEL A_SELANALOG MUXGAINGAINRSSI30dB, 12dB, 24dBATTENATTEN0dB, 12dB, 24dBDETECTPEAKSETRSSIAINAINBINBINAD6600REV. 0 2AD6600SPECIFICATIONSDC SPECIFICATIONSTest AD6600ASTParameter Temp Level Min Typ Max UnitANALOG INPUTS (AIN, AIN/BIN, BIN)Differential Analog Input Voltage Range1Full V 2.0 V p-pDifferential Analog Input Resistance2Full IV 160 200 240 Differential Analog Input Capacitance 25C V 1.5 pFPEAK DETECTOR (Internal), RSSIResolution 3 BitsRSSI Gain Step Full V 6 dBRSSI Hysteresis3Full V 6 dBRESONANT PORT (FLT, FLT)Differential Port Resistance Full V 630 Differential Port Capacitance Full V 1.75 pFA/D CONVERTERResolution Full IV 11 BitsENCODE INPUTS (ENC, ENC)Differential Input Voltage (AC-Coupled)4Full IV 0.4 V p-pDifferential Input Resistance 25C V 11 kDifferential Input Capacitance 25C V 2.5 pFA/B MODE INPUTS (A_SEL, B_SEL)5Input High Voltage Range Full IV 4.75 5.25 VInput Low Voltage Range Full IV 0.0 0.5 VPOWER SUPPLYSupply VoltagesAVCC Full II 4.75 5.0 5.25 VDVCC Full IV 3.0 3.3 5.25 VSupply CurrentIAVCC (AVCC = 5.0 V) Full II 145 182 mAIDVCC (DVCC = 3.3 V) Full II 15 20 mAPOWER CONSUMPTION6Full II 775 976 mWNOTES1Analog Input Range is a function of input frequency. See ac specifications for 70 MHz250 MHz inputs.2Analog Input Impedance is a function of input frequency. See ac specifications for 70 MHz450 MHz inputs.3Six dB of digital hysteresis is used to eliminate level uncertainty at the RSSI threshold points due to noise and amplitude variations.4Encode inputs should be ac-coupled and driven differentially. See Encoding the AD6600 for details.5A_SEL and B_SEL should be tied directly to ground or AVCC.6Maximum power consumption is computed as maximum current at nominal supplies.Specifications subject to change without notice.DIGITAL SPECIFICATIONSTest AD6600ASTParameter Temp Level Min Typ Max UnitLOGIC OUTPUTS (D10D0, AB_OUT, RSSI20)1Logic Compatibility CMOSLogic 1 Voltage (DVCC = 3.3 V) Full II 2.8 DVCC 0.2 VLogic 0 Voltage (DVCC = 3.3 V) Full II 0.2 0.5 VLogic 1 Voltage (DVCC = 5.0 V) Full IV 4.0 DVCC 0.35 VLogic 0 Voltage (DVCC = 5.0 V) Full IV 0.35 0.5 VOutput Coding (D10D0) Twos ComplementCLK2 OUTPUT1, 2Logic 1 Voltage (DVCC = 3.3 V) Full II 2.8 DVCC 0.2 VLogic 0 Voltage (DVCC = 3.3 V) Full II 0.2 0.5 VLogic 1 Voltage (DVCC = 5.0 V) Full IV 4.0 DVCC 0.3 VLogic 0 Voltage (DVCC = 5.0 V) Full IV 0.35 0.5 VNOTES1Digital output load is one LCX gate.2CLK2 output voltage levels, high and low, tested at switching rate of 10 MHz.Specifications subject to change without notice.(AVCC = 5 V, DVCC = 3.3 V; TMIN = 40C, TMAX = +85C unless otherwise noted.)(AVCC = 5 V, DVCC = 3.3 V; TMIN = 40C, TMAX = +85C unless otherwise noted.)REV. 0 3AD6600TIMING REQUIREMENTS AND SWITCHING SPECIFICATIONS1 (AVCC = 5 V, DVCC = 3.3 V; ENC and ENC = 20 MSPS; TMIN = 40C, TMAX = +85C unless otherwise noted.)Test AD6600ASTParameter Name Temp Level Min Typ Max UnitA/D CONVERTERConversion Rate fENC1/(tENC) MSPSMaximum Conversion Rate Full II 20 MSPSMinimum Conversion Rate Full IV 6 MSPSAperture Uncertainty tj25C V 0.3 ps rmsENCODE INPUTS (ENC, ENC)2Period tENCFull II 50 nsPulsewidth High3tENCHFull IV 20 nsPulsewidth Low4tENCLFull IV 20 ns2 CLOCK OUTPUT (CLK2)5Output Frequency 2 fENCMSPSOutput Period6tCLK2_1Full V tENCLnstCLK2_2Full V tENCHnsCLK2 Pulsewidth Low6tCLK2LFull V tENCH/2 nsOutput Risetime7Full V 3 nsOutput Falltime7Full V 2.6 nsOUTPUT RISE/FALL TIMES8Output Risetime (D10:D0, RSSI2:0) Full V 8 nsOutput Falltime (D10:D0, RSSI2:0) Full V 8.4 nsOutput Risetime (AB_OUT) Full V 6 nsOutput Falltime (AB_OUT) Full V 6.2 nsNOTES1See AD6600 Timing Diagrams.2All switching specifications tested by driving ENC andENC differentially.3Several timing specifications are a function of Encode high time, tENCH; these specifications are shown in the data tables and timing diagrams. Encode duty cycleshould be kept as close to 50% as possible.4Encode pulse low directly affects the amount of settling time available at FLT resonant port. See External Analog (Resonant) Filter section for details.5The 2 Clock is generated internally, therefore some specifications are functions of encode period and duty cycle. All timing measurements to or from CLK2 arereferenced to 2.0 V crossing.6This specification IS a function of Encode period and duty cycle; reference timing diagrams Figure 8.7Output rise time is measured from 20% point to 80% point of total CLK2 voltage swing; output fall time is measured from 80% point to 20% point of total CLK2voltage swing.8Output rise time is measured from 20% point to 80% point of total data voltage swing; output fall time is measured from 80% point to 20% point of total data voltageswing. All outputs specified with 10 pF load.Specifications subject to change without notice.REV. 0 4AD6600SPECIFICATIONSTIMING REQUIREMENTS AND SWITCHING SPECIFICATIONS1, 2(AVCC = 5 V, DVCC = 3.3 V; ENC and ENC = 20 MSPS, Duty Cycle = 50%; TMIN = 40C, TMAX = +85C unless otherwise noted.)Test AD6600ASTParameter Name Temp Level Min Typ Max UnitENCODE/CLK2Encode Rising to CLK2 Falling3tCFFull IV 6.5 8.0 9.5 nsEncode Rising to CLK2 Rising4tCRFull IV tCF + (tENCH)/2 ns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 25.7 27.2 28.7 ns@ Encode = 20 MSPS, 50% Duty Cycle Full IV 19.0 20.5 22.0 nsCLK2/DATA (D10:0, RSSI2:0)5CLK2 to DATA Rising Low Delay3t2_DRLFull IV 3.0 6.5 nsCLK2 to DATA Hold Time3tH_D2Full IV 3.0 6.5 nsCLK2 to DATA Falling Low3, 6t2_DFL25C IV 10.0 15.0 20.0 nsFull IV 11.0 15.5 22.0 nsCLK2 to DATA Setup Time4tS_D2Full IV tENCH t2_DFLns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 16.5 23.0 ns@ Encode = 20 MSPS, 50% Duty Cycle625C IV 5.0 10.0 nsFull IV 3.0 9.5 nsCLK2/AB_OUT5CLK2 to AB_OUT Rising Low Delay3t2_ARLFull IV 7.0 11.0 nsCLK2 to AB_OUT Hold Time3tH_A2Full IV 7.0 11.0 nsCLK2 to AB_OUT Falling Low Delay3, 6t2_AFL25C IV 12.0 18.0 23.0 nsFull IV 10.7 19.0 26.0 nsCLK2 to AB_OUT Setup Time4tS_A2Full IV tENCH t2_AFLns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 12.5 19.5 ns@ Encode = 20 MSPS, 50% Duty Cycle625C IV 2.0 7.0 nsFull IV 1.0 6.0 nsENCODE/DATA (D10:0, RSSI2:0)ENCODE to DATA Rising Low Delay4tEN_DRLFull IV tCR + t2_DRLnsENCODE to DATA Hold Time4tH_DENFull IV tEN_DRLns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 28.7 33.7 ns@ Encode = 20 MSPS, 50% Duty Cycle Full IV 22.0 27.0 nsENCODE to DATA Falling Low Delay4tEN_DFLFull IV tCR + t2_DFLnsENCODE to DATA Delay (Setup)4tS_DENFull IV tENC tEN_DFLns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 26.2 34.2 ns@ Encode = 20 MSPS, 50% Duty Cycle625C IV 8.0 14.5 nsFull IV 6.0 14.0 nsENCODE/AB_OUTENCODE to AB_OUT Rising Low Delay4tEN_ARLFull IV tCR + t2_ARLnsENCODE to AB_OUT Delay (Hold)4tH_AENFull IV tEN_ARLns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 32.7 38.2 ns@ Encode = 20 MSPS, 50% Duty Cycle Full IV 26.0 31.5 nsENCODE to AB_OUT Falling Low Delay4tEN_AFLFull IV tCR + t2_AFLnsENCODE to AB_OUT Delay (Setup)4tS_AENFull IV tENC tEN_AFLns@ Encode = 13 MSPS, 50% Duty Cycle Full IV 22.2 30.7 ns@ Encode = 20 MSPS, 50% Duty Cycle625C IV 5.0 11.5 nsFull IV 2.0 10.5 nsNOTES1See AD6600 Timing Diagrams.2All switching specifications tested by driving ENC andENC differentially.3This specification IS NOT a function of Encode period and duty cycle.4This specification IS a function of Encode period and duty cycle.5CLK2 referenced to 2.0 V crossing; digital output levels referenced to 0.8 V and 2.0 V crossings; all outputs with 10 pF load.6For these particular specifications, the 25C specification is valid from 25C to 85C. The Full temperature specification includes cold temperature extreme andcovers the entire range, 40C to +85C.Specifications subject to change without notice.REV. 0 5AD6600AC SPECIFICATIONSTest AD6600ASTParameter Temp Level Min Typ Max UnitANALOG INPUTS1Analog Input 3 dB Bandwidth2Full V 450 MHzDifferential Analog Input Voltage Range70 MHz Full V 2.45 V p-p150 MHz Full V 2.57 V p-p200 MHz Full V 2.62 V p-p250 MHz Full V 2.86 V p-pDifferential Analog Input Impedance370 MHz 25C V 197j24 150 MHz 25C V 188j48 200 MHz 25C V 175j57 250 MHz 25C V 161j67 300 MHz 25C V 151j73 350 MHz 25C V 140j80 400 MHz 25C V 141j75 450 MHz 25C V 173j107 Full-Scale Input Power70 MHz Full V 5.8 dBm150 MHz Full V 6.3 dBm200 MHz Full V 6.7 dBm250 MHz Full V 7.7 dBmFull-Scale Gain Tolerance470 MHz250 MHz Full V 0.5 dB200 MHz525C I 1.0 0.1 +1.0 dBGain ErrorAIN = 200 MHz@ 76 dBFS 25C I 1.5 +1.5 dBGain Matching (Input A:B)70 MHz250 MHz Full V 0.1 dB200 MHz Full II 0.5 0.05 +0.5 dBRange-to-Range Gain Tolerance70 MHz250 MHz Full V 0.1 dBRange-to-Range Phase Tolerance70 MHz Full V 0.2 Degree250 MHz Full V 0.5 DegreeChannel Isolation670 MHz250 MHz Full IV 45 50 dBNoise7Minimum Attenuation Level Full V 34 V rmsMaximum Attenuation Level Full V 869 V rmsAttenuator 3OIP8Full V +33 dBmSignal-to-Noise Ratio (SNR)9, 10, 11AIN = 70 MHz@ 1 dBFS 25C IV 55 59 dB@ 6 dBFS 25C V 54.5 dB@ 10 dBFS 25C IV 45 49 dB@ 12 dBFS to 42 dBFS 25C IV 41 48 6 dB@ 54 dBFS 25C IV 31 34 dBAIN = 150 MHz@ 1 dBFS 25C IV 55 58 dB@ 6 dBFS 25C V 54 dB@ 10 dBFS 25C IV 45 49 dB@ 12 dBFS to 42 dBFS 25C IV 41 48 6 dB@ 54 dBFS 25C IV 31 34 dB(AVCC = 5 V, DVCC = 3.3 V; ENC and ENC = 20 MSPS, Duty Cycle = 50%; TMIN = 40C, TMAX = +85C unlessotherwise noted.)REV. 0 6AD6600SPECIFICATIONSAC SPECIFICATIONS (continued)Test AD6600ASTParameter Temp Level Min Typ Max UnitANALOG INPUTS (Continued)Signal-to-Noise Ratio (Continued)AIN = 200 MHz@ 1 dBFS 25C I 55 57.5 dB@ 6 dBFS 25C V 53.5 dB@ 10 dBFS 25C I 45 49 dB@ 12 dBFS to 42 dBFS 25C I 40.5 48 6 dB@ 54 dBFS 25C I 31 34 dBAIN = 250 MHz@ 1 dBFS 25C IV 52 56 dB@ 6 dBFS 25C V 53.5 dB@ 10 dBFS 25C IV 43 49 dB@ 12 dBFS to 42 dBFS 25C IV 40 48 6 dB@ 54 dBFS 25C IV 30 34 dBSECOND HARMONICAIN = 70 MHz@ 1 dBFS Full V 69 dBc@ 6 dBFS Full V 68 dBc@ 12 dBFS to 42 dBFS Full V 68 6 dBcAIN = 150 MHz@ 1 dBFS Full V 60 dBc@ 6 dBFS Full V 59 dBc@ 12 dBFS to 42 dBFS Full V 67 6 dBcAIN = 200 MHz9, 10, 11@ 1 dBFS 25C I 50 60 dBc@ 6 dBFS Full V 56 dBc@ 10 dBFS 25C I 48 55 dBc@ 12 dBFS to 42 dBFS Full V 65 6 dBc@ 54 dBFS Full V 50 dBcAIN = 250 MHz@ 1 dBFS Full V 54 dBc@ 6 dBFS Full V 62 dBc@ 12 dBFS to 42 dBFS Full V 65 6 dBcTHIRD HARMONICAIN = 70 MHz@ 1 dBFS Full V 77 dBc@ 6 dBFS Full V 76 dBc@ 12 dBFS to 42 dBFS Full V 67 6 dBcAIN = 150 MHz@ 1 dBFS Full V 65 dBc@ 6 dBFS Full V 70 dBc@ 12 dBFS to 42 dBFS Full V 66 6 dBcAIN = 200 MHz9, 10, 11@ 1 dBFS 25C I 50 55 dBc@ 6 dBFS Full V 58 dBc@ 10 dBFS 25C I 55 66 dBc@ 12 dBFS to 42 dBFS Full V 65 6 dBc@ 54 dBFS Full V 62 dBcAIN = 250 MHz@ 1 dBFS Full V 50 dBc@ 6 dBFS Full V 56 dBc@ 12 dBFS to 42 dBFS Full V 65 6 dBcAIN = 70 MHz250 MHz@ 75 dBFS Full IV 28 35 dBcREV. 0 7AD6600AC SPECIFICATIONS (continued)Test AD6600ASTParameter Temp Level Min Typ Max UnitWORST OTHER SPUR (4th or Higher)AIN = 70 MHz@ 1 dBFS Full V 74.5 dBc@ 6 dBFS Full V 71 dBc@ 12 dBFS to 42 dBFS Full V 68 6 dBcAIN = 150 MHz@ 1 dBFS Full V 67 dBc@ 6 dBFS Full V 65 dBc@ 12 dBFS to 42 dBFS Full V 67 6 dBcAIN = 200 MHz@ 1 dBFS 25C I 60 67 dBc@ 6 dBFS Full V 66 dBc@ 10 dBFS 25C I 55 66 dBc@ 12 dBFS to 42 dBFS Full V 65 6 dBcAIN = 250 MHz@ 1 dBFS Full V 66.5 dBc@ 6 dBFS Full V 65 dBc@ 12 dBFS to 42 dBFS Full V 65 6 dBcNOTES1AIN, AIN/BIN, BIN: The AD6600 analog inputs are unconditionally stable and guarantee proper operation over the 70 MHz250 MHz specified operating range.Circuit board layout is critical on this device, and proper PCB layout must be employed to achieve specified results.2Analog Input 3 dB Bandwidth is determined by internal track-and-hold. The front-end attenuators have a bandwidth of 1 GHz.3Measured real and imaginary values using Network Analyzer.4Full-scale gain tolerance is the typical variation in gain at a given IF input frequency. The nominal value for full-scale input power is a function of frequency asshown in previous specification.5Full-scale gain tolerance measured at 200 MHz analog input referenced to 6.7 dBm nominal full-scale input power. For the gain measurement test, the input signallevel is set to 6 dBFS. Tuning port bandwidth is set to 50 MHz.6Main channel set to full-scale input power. Diversity channel swept from 20 dBFS to 90 dBFS.7Measurement includes thermal and quantization noise at 70 MHz analog input. Tuning port bandwidth is set to 50 MHz.8Test tones at 160.05 MHz and 170.05 MHz.9Measurements at 1 dFBS, 6 dBFS, and 10 dBFS are in highest attenuation mode, RSSI = 101.10Each gain-range is checked at ~3 dB from RSSI trip point (not in hysteresis); nominally 16 dBFS (RSSI = 100), 22 dBFS (RSSI = 011), 28 dBFS (RSSI = 010),35 dBFS (RSSI = 001).11Measurement at 54 dBFS is in the lowest attenuation mode, RSSI = 000.Specifications subject to change without notice.REV. 0AD66008ABSOLUTE MAXIMUM RATINGS1Parameter Min Max UnitELECTRICALAVCC Voltage 0 7 VDVCC Voltage 0 7 VAnalog Input Voltage20 AVCC VAnalog Input Current225 mADigital Input Voltage30 AVCC VOutput Current44 mAResonant Port Voltage50 AVCC VENVIRONMENTAL6Operating Temperature Range(Ambient) 40 +85 CMaximum Junction Temperature 150 CLead Temperature (Soldering, 10 sec) 300 CStorage Temperature Range (Ambient) 65 +150 CNOTES1Absolutemaximumratingsarelimitingvaluestobeappliedindividually,andbeyondwhichtheserviceabilityofthecircuitmaybeimpaired.Functionaloperabilityisnotnecessarilyimplied.Exposuretoabsolutemaximumratingconditions for an extended period of time may affect device reliability.2Pins AIN, AIN, BIN, BIN.3Pins ENC, ENC, A_SEL, B_SEL.4Pins D10:0, RSSI2:0, AB_OUT, CLK2.5Pins FLT, FLT.6Typical thermal impedance (44-lead LQFP); JC = 16C/W, JA = 55C/W.EXPLANATION OF TEST LEVELSTest LevelI. 100% Production Tested.II. 100% Production Tested at 25C and guaranteed by designand characterization at temperature extremes.IV. Parameter is guaranteed by design and characterizationtesting.V. Parameter is a typical value only.ORDERING GUIDETemperature Package PackageModel Range Description OptionAD6600AST 40C to 44-Terminal LQFP ST-44+85C (Low-Profile Quad(Ambient) Plastic Flatpack)AD6600ST/PCB Evaluation Boardwith AD6600ASTCAUTIONESD(electrostaticdischarge)sensitivedevice.Electrostaticchargesashighas4000 Vreadilyaccumulate on the human body and test equipment and can discharge without detection. Althoughthe AD6600 features proprietary ESD protection circuitry, permanent damage may occur on devicessubjectedtohigh-energyelectrostaticdischarges.Therefore,properESDprecautionsarerecom-mended to avoid performance degradation or loss of functionality.WARNING!ESD SENSITIVE DEVICEREV. 0 9AD6600PIN FUNCTION DESCRIPTIONSPin Number Name Function1, 33 DVCC Digital VCC for Digital Outputs. Can be 3.3 V.2, 5, 13, 19, 21, 24, 30, 32 GND Ground.3 C1 Internal Bias Point. Bypass by 0.01 F to GND.4, 14, 15, 18, 20, 25, 31 AVCC 5 V Power Supply.68 RSSI[2:0] RSSI Digital Output Bits.9, 10 B_SEL, A_SEL Mode Select Pins for Analog Input Channel A and B Sampling.11 AIN True Analog Input Channel A.12 AIN Complementary Analog Input Channel A.16, 17 FLT, FLT Resonant Filter Pins for External LC Noise Filter.22 BIN Complementary Analog Input Channel B.23 BIN True Analog Input Channel B.26 ENC Complementary Encode Input.27 ENC True Encode Input.28 CLK2 2 Clock Output Used for Clocking Digital Filter Chips.29 AB_OUT Digital Output Flag Indicating Whether Output Is Input A (High) or B (Low).34 D0 Digital Data Output Bit (Least Significant Bit)*.3543 D1D9 Digital Data Output Bits*.44 D10 Digital Data Output Bit (Most Significant Bit)*.*Digital Outputs (D10:D0) in Twos Complement Format.PIN CONFIGURATION345671210118940 39 38 41 42 43 44 36 35 34 372930313233272825262324PIN 1IDENTIFIERTOP VIEW(Not to Scale)12 13 14 15 16 17 18 19 20 21 22DVCCGNDAVCCGNDAB_OUTCLK2ENCAD6600ENCAVCCGNDBINGNDD10 (MSB)D9D8D7D6D5D4D3D2D1D0 (LSB)AVCCGNDBINFLT AINGNDAVCCAVCCFLTAVCCDVCCGNDC1AVCCGNDRSSI2RSSI1RSSI0B_SELA_SELAINREV. 0AD660010DEFINITIONS OF SPECIFICATIONSAnalog BandwidthThe analog input frequency at which the spectral power of thefundamental frequency (as determined by the FFT analysis) isreduced by 3 dB. The bandwidth is determined by the internaltrack-and-hold when the filter node is resonated.Aperture DelayThe delay between the 50% point of the rising edge of theENCODE command and the instant at which the analog input-is sampled.Aperture Uncertainty (Jitter)The sample-to-sample variation in aperture delay.Attenuator 3OIPThe third order intercept point of the front end of the AD6600.It is the point at which the third order products would theoreti-cally intercept the input signal level if the input level could increasewithout bounds. This is measured using the ADC within theAD6600 while the input is stimulated with dual tones in theminimum attenuation (i.e., maximum gain) range.Channel IsolationThe amount of signal leakage from one channel to the nextwhen one channel is driven with a full-scale input, and the otherchannel is swept from 20 dBFS to 90 dBFS with a frequencyoffset. The leakage is measured on the side with the smaller signal.Differential Analog Input Resistance, Differential AnalogInput Capacitance and Differential Analog Input ImpedanceThe real and complex impedances measured at each analoginput port. The resistance is measured statically and the capaci-tance and differential input impedances are measured with anetwork analyzer.Differential Analog Input Voltage RangeThe peak-to-peak differential voltage that must be applied to theconverter to generate a full-scale response. Peak differentialvoltage is computed by observing the voltage on a single pin andsubtracting the voltage from the other pin, which is 180 degreesout of phase. Peak-to-peak differential is computed by rotatingthe inputs phase 180 degrees and taking the peak measurementagain. The difference is then computed between both peakmeasurements.Differential NonlinearityThe deviation of any code width from an ideal 1 LSB step.Differential Resonant Port ResistanceThe resistance shunted across the resonant port (nominally630 ). Used to determine the filter bandwidth and gain ofthat stage.Encode Pulsewidth/Duty CyclePulsewidth high is the minimum amount of time that theENCODE pulse should be left in logic 1 state to achieve ratedperformance; pulsewidth low is the minimum time ENCODEpulse should be left in low state. See timing implications ofchanging tENCH in text. At a given clock rate, these specificationsdefine an acceptable Encode duty cycle.Full-ScaleGainToleranceUnit-to-unit variation in full-scale input power.Full-Scale Input PowerExpressed in dBm. Computed using the following equation: PowerVZFULL SCALEFULL SCALE rmsINPUT=100 0012log.Gain Matching (Input A:B)Variation in full-scale power between A and B inputs.Harmonic Distortion, 2ndThe ratio of the rms signal amplitude to the rms value of thesecond harmonic component, reported in dBc.Harmonic Distortion, 3rdThe ratio of the rms signal amplitude to the rms value of thethird harmonic component, reported in dBc.Integral NonlinearityThe deviation of the transfer function from a reference linemeasured in fractions of 1 LSB using a best straight linedetermined by a least square curve fit.MinimumConversionRateThe encode rate at which the SNR of the lowest analog signal fre-quency drops by no more than 3 dB below the guaranteed limit.Maximum Conversion RateThe encode rate at which parametric testing is performed.Noise (For Any Range Within the ADC) V ZNOISEFS SNR SignaldBm dBc dBFS= 0 001 1010.where:Z is the input impedance,FS is the full-scale of the device for the frequency in question,SNR is the value for the particular input level,Signal is the signal level within the ADC reported in dB belowfull scale. This value includes both thermal and quanti-zation noise.Range-Range Gain ToleranceThe gain error in the RSSI attenuator ladder from one range tothe next.Range-Range Phase ToleranceThe phase error in the RSSI attenuator ladder from one rangeto the next.Differential Resonant Port CapacitanceThe capacitance between the two resonant pins. Used to deter-mine filter bandwidth and resonant frequency.REV. 0AD660011RSSIGainStepThe input amplitude span between taps of the RSSI (receivedsignal strength) attenuator ladder. Ideally each stage shouldspan 6 dB of input power.RSSI HysteresisThe amount of movement in the RSSI switch points, dependingon the direction of approach. Hysteresis prevents unnecessaryRSSI toggling when input signal power is near a threshold.Signal-to-Noise Ratio (Without Harmonics)The ratio of the rms signal amplitude (set at 1 dB below fullscale) to the rms value of the sum of all other spectral compo-nents, excluding the first five harmonics and dc.Worst Other SpurThe ratio of the rms signal amplitude to the rms value of theworst spurious component (excluding the second and thirdharmonic) reported in dBc.AD6600TRANSFERFUNCTIONAIN LEVEL dBFS60240100 0 90SNR dB80 70 60 50 40 30 20 10543018642361248Figure 1. SNR vs. Input PowerREV. 0AD660012EQUIVALENTCIRCUITS100100ATTENUATOR STAGEEQUIVALENT INPUT RSHOWN ONLYAVCCAVCCGNDGNDVREFAINAIN4/8 GAIN STAGEBUF GAIN BUFFigure 2. Analog Input Stage (Channel A Shown;Channel B Is Equivalent)AVCCGNDGNDAVCCBIASAVCCGNDB_SELISEL_A ISEL_BA_SELFigure 3. A_SEL, B_SEL Input Mode PinsDVCCCURRENTMIRRORDVCCCURRENTMIRRORVREFD10D0RSSI [2:0]500Figure 4. Digital Outputs315 315AVCCGNDAVCCGNDAVCCGNDFROMGAIN STAGETO T/HEXTERNAL LC FILTERFLT FLTFigure 5. Resonant (LC Noise Filter) PortR117k1/2R117k1/2R28k1/2R28k1/2AVCCENCODE ENCODEAVCCTIMINGCIRCUITSAVCCFigure 6. Encode InputsDVCCCURRENTMIRRORDVCCCURRENTMIRRORVREFCLK2AB_OUTFigure 7. CLK2, AB_OUT OutputsREV. 0AD660013AD6600 TIMING DIAGRAMSENCODECLK2D [10:0]RSSI [2:0]AB_OUTtCLK2H1tCLK2H2tCLK2LtCF2tCLK2LtCF1CLK22 CLK21 CLK22 CLK21 CLK22t21_DRLt21_ARLtENCHtENCLtENCtCLK21tCLK22tCR2tCR1t21_DFLt21_AFLFigure 8. Encode to CLK2 Delays and CLK2 Propagation DelaysENCODECLK2D [10:0]RSSI [2:0]AB_OUTtCLK2H1tCLK2H2tCLK2LtCF2tCLK2LtCF1CLK22 CLK21 CLK22 CLK21 CLK22tH_D2tENCHtENCLtENCtCLK21tCLK22tCR2tCR1tS_D2tH_D2tS_D2tH_A2tS_A2 tH_A2tS_A2Figure 9. CLK2 Setup-and-Hold Time CharacteristicsENCODECLK2D [10:0]RSSI [2:0]AB_OUTtCLK2H1tCLK2H2tCLK2LtCF2tCLK2LtCF1CLK22 CLK21 CLK22 CLK21 CLK22tENCHtENCLtENCtCLK21tCLK22tCR2tCR1tEN_DFL tEN_AFLENCODE ENCODE ENCODEtEN_ARLtEN_DRLFigure 10. Encode to CLK2 Delays and Encode Propagation DelaysREV. 0AD660014ENCODECLK2D [10:0]RSSI [2:0]AB_OUTtCLK2H1tCLK2H2tCLK2LtCF2tCLK2LtCF1CLK22 CLK21 CLK22 CLK21 CLK22tENCHtENCLtENCtCLK21tCLK22tCR2tCR1tS_DENtH_DENtS_DENtH_DENtH_AEN tS_AENtH_AENtS_AENENCODE ENCODE ENCODEFigure 11. Encode Setup-and-Hold Time CharacteristicsCLK2D [10:0]RSSI [2:0]AB_OUT3 2.68 8.46.26Figure 12. Typical Output Rise and Fall TimesENCODECLK220 30 5020 30 18 188 840%Figure 13. Encode = 20 MSPS, Duty Cycle = 40%ENCODECLK220 30 5020 308 860%23 23Figure 14. Encode = 20 MSPS, Duty Cycle = 60%REV. 0AD660015THEORY OF OPERATIONThe AD6600, dual-channel, gain-ranging ADC integrates ana-log IF circuitry with high speed data conversion. Each analoginput stage is a 1 GHz, 0 dB to 24 dB, phase-compensated stepattenuator; the step size in each attenuator is 12 dB. Both inputstages drive an analog multiplex function followed by a 12 dB/18 dB gain amplifier. A simple LC noise filter at the output ofthe gain amplifier is required to resonate at the desired IF. Thisresonant filter port precedes a wide input bandwidth (450 MHz)track-and-hold followed by an 11-bit analog-to-digital converter(ADC). A high speed synchronous peak detector monitors sig-nal strength at both input channels. The peak detector drivesRSSI circuitry that automatically adjusts attenuation and gainon a clock-by-clock basis. The three RSSI indicator bits and theeleven ADC bits are available at the output providing an exponentand mantissa data format. Together these integrated componentsform an IF sampling, high dynamic range ADC system.It is helpful to view this device as a stand-alone ADC usingautomatic gain control. The gain control referred to in this datasheet as gain-ranging works to maintain a constant SNR overas wide a range as possible.As stated previously, the AD6600 has a floating-point output:eleven mantissa bits and three exponent bits. As shown in Fig-ure 16, at the lowest input levels SNR increases 1 dB for a 1 dBincrease in input power. In this range, the AD6600 is set formaximum gain. However, when the input signal level reachesthe gain-ranging section (approximately 42 dBFS), the SNR iscontained between about 50 dB and 56 dB or between 44 dB and56 dB including the effects of hysteresis. Although Figure 16does not indicate so, there are slight differences between theSNR from one gain range to the next as the gain amp switchesbetween 12 dB and 18 dB. Once the final RSSI range has beenexceeded (approximately 12 dBFS), SNR again increases 1 dBper 1 dB input power increase until converter full scale is reached.Again, this performance is very much like the effects of a typicalanalog AGC loop.GAINA/DCONVERTERTIMINGENCODESELECT GAIN+12, +18dBENCODEFLT FLTNOISE FILTERRESONANTPORT630RSSI3TWO'SCOMPLEMENT11AB_OUTD10D0RSSI [2:0]CLK2DVCC ENC ENC GND AVCC B_SEL A_SELANALOG MUXGAINGAINRSSI30dB, 12dB, 24dBATTENATTEN0dB, 12dB, 24dBDETECTPEAKSETRSSIAINAINBINBINAD6600Figure 15. Functional Block DiagramSNR dB124824 28AIN dBFS32 36 40 44 48 52 56 601842543036602466727884909609020 16 12 8 4 012dB SNR WINDOW101100011010001000101100011010001000Figure 16. SNR for Gain-Ranging ADCAD6600 SUBCIRCUITSInput Step Attenuator and Gain StageThe AD6600 has two identical input attenuators, Channel Aand Channel B. These dual inputs are typically used as diversitychannels but may also process two independent IF signals. Formaximum oversampling the device is used in single channel mode;in this case only one input channel is required. The attenuatorsteps are 0 dB, 12 dB and 24 dB. The attenuator settings arebased on the decisions of the RSSI stage (see Peak Detector/RSSI section). The outputs of the attenuators connect to ananalog multiplexer that selects either Channel A or B for subse-quent processing (see Input Mode). The selected signal drivesa dual-gain amplifier set to either 12 dB or 18 dB; the selectedgain is also determined by the RSSI stage. Therefore, based onall possible combinations of attenuation and gain, the inputsignal receives 12 dB to +18 dB of voltage gain in 6 dB steps(Table I). Overall gain-matching is typically within 0.1 dB. Witha bandwidth of 1 GHz, the phase delay through the front-endranges from 0.2 degrees to 0.5 degrees, depending on inputfrequency. Additionally, the input impedance does not changewith attenuator settings so there is no AM-to-PM distortion.REV. 0AD660016Table I. Attenuator and Gain SettingsAttenuator Gain Amp Total RSSI Word0 dB +18 dB +18 dB 0000 dB +12 dB +12 dB 00112 dB +18 dB +6 dB 01012 dB +12 dB 0 dB 01124 dB +18 dB 6 dB 10024 dB +12 dB 12 dB 101High-Speed Peak Detector and RSSI CircuitryThe peak detector along with the attenuator and dual gainamplifier form the control loop within the AD6600.The peak detector is designed to follow the analog input one clockcycle before the conversion is actually made. Therefore, while theconverter section of the AD6600 is converting sample n, thepeak detector is already looking at sample n+1. While look-ing at the n+1 sample (the calibration period), the peak detec-tor examines the envelope of the input signal. The more of anenvelope that is tracked, the more accurate the gain setting. Atthe very least, the peak detector must be presented either a positiveor negative sinusoidal peak, which represents about one-half of asine wave cycle. Since the peak detector works for a complete cycleprior to conversion, the absolute minimum IF frequency that canbe determined is twice the sample rate per channel. Therefore,at 15 MSPS, the minimum IF frequency that can be sampledwould be 30 MHz.Note that the more cycles of the input that are monitored by thepeak detector, the more accurate the gain setting will be. There-fore, the actual minimum IF frequency recommended is higherthan this. The minimum specified frequency is 70 MHz. Since theRSSI control loop is performed on a sample-by-sample basis,the AD6600 very accurately follows the signals into and out of adeep fade.HysteresisThe AD6600 employs hysteresis to prevent the gain-ranging fromunnecessarily changing when the signal envelope is near an RSSIthreshold. The hysteresis is digital and will account for exactly6 dB of shift, depending on whether the signal is increasing ordecreasing. This effect is shown in the dashed lines of the over-all transfer function, Figure 16.External LC Noise Filter, Resonant PortThe output of the attenuator/gain stage drives the wide bandwidthtrack-and-hold (T/H), followed by the ADC encoder. Because theattenuator/gain stage has a very wide bandwidth (~1 GHz), anLC filter or resonant port is provided to limit the amount ofwideband noise delivered to the ADC. The simple LC filter doesnot provide signal selectivity and should typically be 35 MHz to50 MHz wide. However, because the ADCs track-and-hold itselfhas a wide bandwidth (~450 MHz), this noise-limiting filter iscritical to meeting overall sensitivity. Specific details on select-ing components for the resonant port are provided later in thetext (Understanding the External Analog Filter).ADC EncoderAfter the calibration period is complete (one clock cycle), theappropriate gain and attenuator settings are determined and set.Once settled, the internal track-and-hold freezes the input signalso that the ADC encoder may digitize the signal. During digiti-zation, the peak detector/RSSI circuitry is already looking at thenext sample. When the AD6600 is in dual channel mode, theprocess is interleaved: while Channel B is monitored for signalstrength, Channel A is digitized. This allows the RSSI to updateon a clock-by-clock basis.DIGITIZEOLD DATAT-AND-H HOLDT-AND-H TRACKADC DIGITIZET-AND-H HOLDRSSICAL.RSSI SETNOISE FILTERDISCHARGENOISE FILTERSETTLING4/8 AMPCLAMPEDNOISE FILTERSETTLINGENCODEIF INPUTINTERNAL2 CLOCKRSSICALIBRATIONAMPLIFIERCONTROLT/H INPUTFigure 17. Internal TimingFigure 17 shows the internal timing of the chip. The encodeapplied to the device initiates several actions. The first and mostimportant is that the track-and-hold is placed in hold, thussampling the analog input at that instant. The second action is thatthe peak detector of the RSSI circuitry is initialized. During thisperiod, the analog input envelope is monitored to determine signalpower. The AD6600 is in calibration mode for about one-quarter of the encode period.While the AD6600 is in calibration, the external noise filter isdischarged and the amplifier driving the filter disabled. Since thisfilter is shared between the two input channels in dual channelmode, this greatly reduces the feedthrough between the channelsthat would otherwise exist. One-quarter of an encode period afterthe calibration is complete, the amplifier is re-enabled and allowedto settle to its new signal conditions for sampling by the widebandT/H on the next encode signal. The final action is that the signalon the resonant port is sampled by the track-and-hold. Thishappens on the next rising edge of the encode.Input Mode SelectThe AD6600 has two operating modes: single channel and dualchannel. In single channel mode, the ADC always samples Chan-nel A or always samples Channel B. In dual channel mode, theADC converter is sampling Channel A and Channel B on alter-nating Encode cycles. Two control pins are provided to selectthe desired mode of operation. A_SEL and B_SEL arbitrate theselection of how these input channels are connected to the out-put. Table II shows the truth table for selection of the input.REV. 0AD660017Table II. Selecting AD6600 Operating ModeOutput vs. Encode ClockMode A_SEL B_SEL n n+1 n+2 n+3Dual: A/B 1 1 A B A BSingle: A 1 0 A A A ASingle: B 0 1 B B B BNot Valid 0 0 A_SEL and B_SEL are not logic inputs and should be tieddirectly to ground or analog VCC (5 V analog).In dual channel mode, the AB_OUT signal indicates whichinput is currently available on the digital output. When theAB_OUT is 1, the digital output is the digitized version ofChannel A. Likewise, when AB_OUT is 0, the Channel B isavailable on the digital output (Table III).Table III. AB_OUT for Dual Channel OperationOutput Data vs. Encode ClockA_SEL and B_SEL = 1 n n+1 n+2 n+3D[10:0], RSSI[2:0] A B A BAB_OUT 1 0 1 0Data Output StageThe output stage provides data in the form of mantissa, D[10:0],and exponent, RSSI[2:0], where D[10:0] represents the outputof the 11-bit ADC coded as twos complement, and RSSI[2:0]represents the gain-range setting coded in offset binary. TableIV shows the nominal gain-ranges for a nominal 2 V p-p differ-ential full-scale input. Keep in mind that the actual full-scaleinput voltage and power will vary with input frequency.Table IV. Interpreting the RSSI BitsDifferential RSSI [2:0]Analog Input Voltage Decimal Attenuation(V p-p) Binary Equiv. or Gain (dB)0.5 < VIN101 5 120.25 < VIN < 0.5 100 4 60.125 < VIN < 0.25 011 3 00.0625 < VIN < 0.125 010 2 +60.03125 < VIN < 0.0625 001 1 +12VIN < 0.03125 000 0 +18The digital processing chip which follows the AD6600 can com-bine the 11 bits of twos complement data with the 3 RSSI bitsto form a 16-bit equivalent output word. Table V explains howthe RSSI data can be interpreted when using a PLD or ASIC.Basically, the circuit performs right shifts of the data dependingon the RSSI word. This can also be performed in software usingthe following pseudo code fragment:r0 = dm (rssi);r2 = 5;r0 = r2r0;r1 = dm (adc); (11 bits, MSB justified into DSP word)rshift r1, r0; (arithmetic shift to extend the sign bit)The result of the shifted data is a 16-bit fixed-point word thatcan be used as any normal 16-bit word.Table V. 16-Bit, Fixed-Point Data Format16-Bit Data Corresponds to aRSSI 11-Bit Word Format Shift Right of101 DATA DATA 32 5100 DATA DATA 16 4011 DATA DATA 8 3010 DATA DATA 4 2001 DATA DATA 2 1000 DATA DATA 1 0When mated with the AD6620, Digital Receive Processor Chip,the AD6600 floating point data (mantissa + exponent) is automati-cally converted to 16-bit twos complement format by the AD6620.APPLYING THE AD6600Encoding the AD6600The AD6600 encode signal must be a high quality, extremelylow phase noise source to prevent degradation of performance.Digitizing high frequency signals (IF range 70 MHz250 MHz)places a premium on encode clock phase noise. SNR perfor-mance can easily degrade by 3 dB4 dB with 70 MHz inputsignals when using a high-jitter clock source. At higher IFs (upto 250 MHz), and with high-jitter clock sources, the higherslew rates of the input signals reduce performance even further.See AN-501, Aperture Uncertainty and ADC System Performancefor complete details.For optimum performance, the AD6600 must be clocked differ-entially. The encode signal is usually ac-coupled into the ENCand ENC pins via a transformer or capacitors. These pins arebiased internally and require no additional bias.Figure 18 shows one preferred method for clocking the AD6600.The sine source (low jitter) is converted from single-ended todifferential using an RF transformer. The back-to-back Schottkydiodes across the transformer secondary limit clock excursionsinto the AD6600 to approximately 0.8 V p-p differential. Thishelps prevent the larger voltage swings of the clock from feedingthrough to other portions of the AD6600, and limits the noisepresented to the encode inputs. A crystal clock oscillator canalso be used to drive the RF transformer if an appropriatelimiting resistor (typically 100 ) is placed in the series withthe primary.ENCODEENCODEAD6600T11T50822810DIODESSINESOURCE100Figure 18. Transformer-Coupled Sine SourceREV. 0AD660018If a low jitter ECL/PECL clock is available, another option is toac-couple a differential ECL/PECL signal to the encode inputpins as shown in Figure 19.ENCODEENCODEAD66000.1F0.1FVTVTECL/PECLFigure 19. AC-Coupled ECL/PECL EncodeDriving the Analog InputsAs with most new high-speed, high dynamic range analog-to-digitalconverters, the analog input to the AD6600 is differential. Differ-ential inputs allow much improvement in performance on-chipas IF signals are processed through attenuation and gain stages.Most of the improvement is a result of differential analog stageshaving high rejection of even-order harmonics. There are alsobenefits at the PCB level. First, differential inputs have highcommon-mode rejection to stray signals such as ground andpower noise. They also provide good rejection to common-modesignals such as local oscillator feedthrough.Driving a differential analog input introduces some new chal-lenges. Most RF/IF amplifiers are single-ended and may notobviously interface to the AD6600. However, using simpletechniques, a clean interface is possible. The recommendedmethod to drive the analog input port is shown in Figure 20.The AD6600 input is actually designed to match easily to aSAW filter such as SAWTEK 855297. This allows the SAWfilter to be used in a differential mode, which often improves theoperations of a SAW filter. Using network analyzer data forboth the SAW filter output and the AD6600 input ports (seedata tables for AD6600 S11 data), a conjugate match can beused for maximum power transfer. Often an adequate matchcan be achieved simply by using a shunt inductor to make theport look real (Figure 20). For more details on how to exactlymatch networks, see RF Circuit Design by Chris Bowick, ISBN:0-672-21868-2.SAW #1FROMMIXEROUTPUTSAW #2AD6600ADCAD6630Figure 20. Cascaded SAW Filters with AD6630Where gain is required, the AD6630 differential, low noise, IFgain block is recommended. This amplifier provides 24 dB ofgain and provides limiting to prevent damage to the SAW filterand AD6600. The AD6630 is designed to reside between twoSAW filters. This low noise device is ideally suited to manyapplications of the AD6600. For more information on theAD6630, reference the AD6630 data sheet.When general purpose gain blocks are used, matching can easilybe achieved using a transformer. Most gain blocks are availablewith 50 input and output ports. Thus matching to the 200 impedance of the AD6600 requires only a 1:4 (impedance ratio)transformer as shown in Figure 21.AD6600ADC50 GAINBLOCKFROMMIXEROUTPUTFigure 21. Transformer-Coupled Gain BlockIn the rare case that better matching is required, a conjugatematch between the amplifier selected and the transformer-coupled analog input can be achieved by placing the matchingnetwork between the amplifier and the transformer (Figure 22).For more details on matching, see the reference mentionedpreviously for more details.AD6600ADC50 GAINBLOCKFROMMIXEROUTPUTMATCHINGNETWORKFigure 22. Gain Block and Matching NetworkUnderstanding the External Analog FilterTwo primary trade-offs must be made when designing the exter-nal resonant filter. The obvious one is the bandwidth of thefilter. The second, not so obvious, trade-off is settling time ofthe filter nodes.Resonant Filter Bandwidth determines the amount of noise thatis limited at the center frequency chosen. If the resonant filter istoo wide, little noise improvement is seen. If the resonant filteris too narrow, amplitude variation can be seen due to the toler-ance of filter components. If the narrow filter is off center due tothese tolerances (or drift), the 4/8 signal will fall on the transi-tion band of the filter. An optimum starting point for this filteris approximately 50 MHz.Resonant Filter Settling limits the amount of capacitance of thisfilter. The output of the 4/8 amplifier is clamped when theADC is processing its input (encode high time). This prevents theamp output from feeding through to the ADC (T/H) and cor-rupting the ADC results. But, upon the falling edge of encode,the amp must now come out of clamp and present an accuratesignal to the ADC T/H. The RC of the external filter deter-mines the settling of the amp. If the amp output does not settle,the ADC sees an attenuated signal. So obviously, a narrowbandwidth is desired to improve noise performance; but if thefilter is too narrow, the amp will not settle and the ADC will seean attenuated signal.Figure 23 shows a simplified model of the 4/8 amplifier. Akey point to note is that the resistor values in the collector legsare 315 nominal with a tolerance of 20%. The filter perfor-mance is determined by these values in conjunction with theinternal parasitic capacitance, board parasitics and the externalfilter components.REV. 0AD660019315 315FROMGAIN STAGEAVCCGNDCLAMPENCODEFLTFLTRESONANTFILTER PORTFigure 23. 4 /8 Amplifier Clamp CircuitryFigure 24 shows why settling is important for this circuit. If the4/8 amp does not settle (come out of clamp), the amplitudepresented to the ADC will be decreased. This results in decreasedgain when the filter capacitance is too high.ENCODERESONANTFILTERHOLD TRACK HOLDCLAMPEDSETTLINGFigure 24. 4 /8 Amplifier SettlingThis explains why the total capacitance allowed for the externalfilter varies depending on the clock rate (actually encode clockhigh time). If the encode is 13 MSPS and the duty cycle is 50%,the allowable settling time is 38.5 ns (1/2 of the encode time).Our assumption is that the amp should be allowed to settle to1/4 LSB in this time period. This has been proven with bothsimulation and empirical analysis. If the settling is assumed tobe an RC circuit, then:T = RC; t = time; n = number of bits V A eA A A eeetTl nTtl nOt Tn t Tnt Tnt Tnn= ( ) = ( ) = ===( )12 1112112122///// CTR l nnsl npFTOTALENCODE=( )( )=( ) =0 5819238 5315 819213 6...In this case, CTOTAL includes all parasitics and external capaci-tance. R is nominally 315 . The 8192 is (4 2048), which is1/4 LSB of the converter (11 bits, 2048).So for settling purposes, with 13 MSPS encode and 50% dutycycle, the maximum allowable capacitance for proper settling isCTOTAL = 13.6 pF.As stated above, this CTOTAL includes the external capacitors,the board parasitics, and the AD6600 parasitics. The parasiticsof the AD6600 (lead, internal bond pad and internal connec-tions) at FLT and FLT are 1.75 pF 0.35 pF (differential).If the resistors are at maximum value (315 + 20%), the maxi-mum allowable capacitance is CTOTAL = 11.3 pF. If the dutycycle is less than 50%, the maximum allowable capacitance isfurther decreased to allow for settling.Power SuppliesCare should be taken when selecting a power source. Linearsupplies are strongly recommended. Switching supplies tend tohave radiated components that may be received by the AD6600.Each of the power supply pins should be decoupled as closely tothe package as possible using 0.1 F chip capacitors.The AD6600 has separate digital and analog power supply pins.The analog supplies are denoted AVCC and the digital supplypins are denoted DVCC. Although analog and digital suppliesmay be tied together, best performance is achieved when thesupplies are separate. This is because the fast digital outputswings can couple switching current back into the analog sup-plies. Note that AVCC must be held within 5% of 5 Volts; how-ever, the DVCC supply may be varied according to outputdigital logic family. The AD6600 is specified for DVCC = 3.3 Vas this is a common supply for digital ASICS.Output LoadingCare must be taken when designing the data receivers for theAD6600. Note from the equivalent circuits shown earlier (seeEquivalent Circuits) that D[10:0] and RSSI[2:0] contain a500 output series resistor. To minimize capacitive loading,there should only be one gate on each output pin. Extra capaci-tive loading will increase output timing and invalidate timingspecifications. CLK2 and AB_OUT do not contain the outputseries resistors. Testing for digital output timing is performedwith 10 pF loads.Layout InformationThe schematic of the evaluation board (Figure 25) represents atypical implementation of the AD6600. A multilayer board isrecommended to achieve best results. It is highly recommendedthat high quality, ceramic chip capacitors be used to decoupleeach supply pin to ground directly at the device. The pinout ofthe AD6600 facilitates ease of use in the implementation of highfrequency, high resolution design practices. All of the digitaloutputs are segregated to two sides of the chip, with the inputson the opposite side for isolation purposes.Care should be taken when routing the digital output traces. Toprevent coupling through the digital outputs into the analogportion of the AD6600, minimal capacitive loading should beplaced on these outputs. It is recommended that a fanout ofonly one be used for all AD6600 digital outputs.The layout of the analog inputs and the external resonant filterare critical. No digital traces must be routed near, under, orabove these portions of the circuit. The transformers used forcoupling into the analog inputs must be located as close aspossible to the analog inputs of the AD6600. The external reso-nant filter components must be physically close to the filter-input pins, yet separated from the analog inputs.REV. 0AD660020The layout of the Encode circuit is equally critical. Any noisereceived on this circuitry will result in corruption in the digitiza-tion process and lower overall performance. The Encode clockmust be isolated from the digital outputs and the analog inputs.Evaluation BoardThe evaluation board for the AD6600 is straightforward, con-taining all required circuitry for evaluating the device. The onlyexternal connections required are power supplies, clock and theanalog inputs. The evaluation board includes the option for anon-board, clock oscillator for encode.Power to the analog supply pins of the AD6600 is connected viathe power terminal block (TB1). Power for the digital interfaceis supplied via Pin 1 of J201, or the VDD e-hole located adja-cent to J201. The VDD supply can vary between 3.3 V to 5.0 Vand sets the level for the output digital data (J201). The J201connector mates directly with the AD6620 (Receive SignalProcessor) evaluation board, Part # AD6620S/PCB, allowingcomplete evaluation of system performance.The two analog inputs are connected via SMA connectorsAIN and BIN, which are transformer-coupled to the AD6600inputs. The transformers have a turns-ratio of 1:4 to matchthe input resistance of the AD6600 (200 ) to 50 at theSMA connectors.The Encode signal may be generated using an on-board crystaloscillator, U100. If an on-board crystal is used, R104 must beremoved from the board to prevent loading of the oscillatorsoutput. The on-board oscillator may be replaced by an externalencode source via the SMA connector labeled ENCODE. If anexternal source is used, it must be a high quality and very lowphase noise source. The high IF range of the AD6600 (70 MHz250 MHz) demands that the Encode clock be sufficiently pureto maintain performance.The AD6600 output data is latched using 74LCX574 (U201,U202) latches. The clock for these latches is determined byjumper selection on header J1. The clock can be a delayed ver-sion of the encode clock (CLKA, CLKB), or the CLK2 gener-ated by the AD6600. A clock is also distributed with the outputdata (J201) that is labeled CLKX (Pin 11, J201). The CLK isselected with jumpers on header J1 and can be CLKA, CLKB,or CLK2.The resonant LC filter components (SEL2, C2 and C3) areomitted. The user must install proper values based on the IFchosen. See Understanding the External Analog Filter section ofthe data sheet for guidelines on selecting these components.Table VI. AD6600ST/PCB Bill of MaterialItem Quantity Reference Description1 3 AIN, BIN, ENCODE SMA Connector2 14 C1, C102108, C114, C117118, Ceramic Chip Capacitor 1206, 0.1 FC120121, C2993 2 C100101 Tantalum Chip Capacitor, 10 F4 1 C111 Ceramic Chip Capacitor 0805, 0.1 F5 4 C112C113, C115116 Ceramic Chip Capacitor 0508, 0.1 F6 2 CR12 1N2810 Schottky Diode7 1 DUT AD6600AST8 1 J1 20-Pin Double Row Male Header9 1 J201 50-Pin Double Row Male Header, Right Angle10 2 R12 Omitted11 2 R100R101 Surface Mount Resistor 1206, 10 k12 1 R103 Surface Mount Resistor 1206, 100 13 1 R104 Surface Mount Resistor 1206, 50 14 2 R298R299 Surface Mount Resistor 1206, 2 k15 3 T1T2, T4 Surface Mount Transformer Mini-Circuits T41T16 1 TB1 PCTB2 Terminal Block17 2 U201U202 74LCX574 Octal Latch18 1 U204 74LVQ00 Two Input NAND GateREV. 0AD660021AD6600AST2930313233272825262324DVCCGNDAVCCGNDAB_OUTCLK2XENCENCAVCCGNDBIN34567 12101189DVCCGNDC1AVCCGNDRSSI2RSSI1RSSI0B_SELA_SELAIN4039384142434436353437D 1 0D 9D 8D 7D 6D 5D 4D 3D 2D 1D 0( M S B )( L S B )1213141516171819202122G N DA V C CG N DF L TG N DA V C CA V C CF L TA V C CA I NB I NVDDGNDVCCGNDBAC1110.1FC1120.01FSMAAIN4631 2C1150.01FSEL2C3SELC2SELVCCG N DV C CV C CV C CG N DV C CG N DSMABIN4631 2C1160.01FVDDGNDVCCGNDVCCGNDSMAENCODE4631 2C1130.01FC10.1FR1R2CR11N2810CR21N2810C1140.1FCLKREFR10450R103100OUTVCCVEEVCCU1001478K11152CLKCLK_28D8Q7D7Q6D6Q5D5Q4D4Q3D3Q2D2Q1D1QCKOE1213141516171819A/BBIT0BIT1BIT2BIT3BIT4BIT5BIT6111CLKU20174LCX5748D8Q7D7Q6D6Q5D5Q4D4Q3D3Q2D2Q1D1QCKOE1213141516171819BIT7BIT8BIT9BIT10RSSIB2RSSIB1RSSIB0111U20274LCX5749876543298765432D10D9D8D7D6D5D4D3D2D1D0RSSI0RSSI1RSSI2A/BA/BD0D1D2D3D4D5D6D7D8D9D10RSSI2RSSI1RSSI01234567891020191817161514131211H20DMJ1ABCLKCLKACLK_2XCLKBGNDGNDCLKACLKBCLKX5012493484475466457448439421041114012391338143715361635173418331932203121302229232824272526H50DMJ201VDDBIT10BIT9BIT8BIT7BIT6BIT5BIT4BIT3CLKCLKXBIT2BIT1BIT0GNDGNDGNDGNDGNDGNDGNDRSSIB2RSSIB1RSSIB0GNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDA/BGNDR10010kAVCCR10110kBVCC123R2982R2992kVDDC2990.1FCLKREFU20474LVQ009108U20474LVQ00GNDGND121311U20474LVQ00GNDGND456U20474LVQ00CLKA12TB1PCTB2+C100C102C104C106C108C120C121VCC+C101C103C105C107C117C118VDD1:4T4TI4TTI4T1:4T2T14T1:4GNDREMOVE 21 AND 30T1Figure 25. AD6600ST/PCB Schematic DiagramREV. 0AD660022Figure 27. AD6600ST/PCB Top Side CopperFigure 28. AD6600ST/PCB Bottom Side CopperFigure 29. AD6600ST/PCB Power Supply Layer (Negative)Figure 30. AD6600ST/PCB Ground Layer (Negative)Figure 26. AD6600ST/PCB Top Side Silk ScreenREV. 0AD660023Connecting the AD6600 with the AD6620The AD6600 interfaces directly to the AD6620 Digital ReceiveSignal Processor as shown in Figure 31. No additional externalcomponents are required. Note that the layout requirements dis-cussed previously do apply and deviations can result in degradedperformance. The digital outputs of the AD6600 must connectdirectly to the AD6620 inputs with no additional fanout. Addi-tional loading on the outputs will compromise timing performance.AD6600 AD6620(MSB) D10D3D2D1(LSB) D0D9D8D7D6D5D4IN15IN14IN13IN12IN11IN10IN9IN8IN7IN6IN5IN4IN3IN2IN1IN0EXP2EXP1EXP0A/BCLKRSSI2RSSI1RSSI0AB_OUTCLK2ENCENCFigure 31.AD6600/AD6620 ConnectionsFigure 32 shows the timing details between the AD6600 and theAD6620. On Clock 1, D[10:0], RSSI[2:0], and AB_OUT arecaptured by the AD6620.Since AB_OUT has changed state fromthe previous clock, the D[10:0] and RSSI[2:0] are processed bythe AD6620. This clock allows adequate setup and hold timefor AB_OUT, D[10:0], and RSSI[2:0] to be captured by theAD6620.On Clock2, D[10:0], RSSI[2:0], and AB_OUT are capturedby the AD6620. Since AB_OUT has not changed from theprevious clock, the D[10:0] and RSSI[2:0] are ignored by theAD6620. This clock is concerned only with the AB_OUT setup-and-hold time.CLK2D [10:0]RSSI [2:0]AB_OUT38.5 38.53.0 16.57.03.0 16.512.5CLOCK1 CLOCK2Figure 32. AD6600 to AD6620 Timing at 13 MSPSREV. 0AD660024C009662.57/00 (rev. 0)PRINTED IN U.S.A.44-Terminal LQFP (Low-Profile Quad Plastic Flatpack)(ST-44)TOP VIEW(PINS DOWN)1333444111223220.018 (0.45)0.012 (0.30)0.031 (0.80)BSC0.394(10.0)SQ0.472 (12.00) SQ0.057 (1.45)0.053 (1.35)0.006 (0.15)0.002 (0.05)SEATINGPLANE0.063 (1.60)MAX0.030 (0.75)0.018 (0.45)OUTLINE DIMENSIONSDimensions shown in inches and (mm).