DSC0503007C0_A_DMC-LS1PP

ORDER NO. DSC0503007C0 B26

Digital Camera

DMC-LS1PP DMC-LS1PL DMC-LS1EB DMC-LS1EG DMC-LS1EGM DMC-LS1GC DMC-LS1GK DMC-LS1GN DMC-LS1GT DMC-LS1SGVol. 1Colour (S)...........Silver Type (A)...........Blue Type (GC and GK only) (T)...........Brown Type (GC only)

2005 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.

DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG

CONTENTSPage1 INTRODUCTION 1.1. INTRODUCTION 1.2. ABOUT LEAD FREE SOLDER (PbF) 1.3. IMPORTANT NOTICE 1: (Other than U.S.A. and Canadian Market) 1.4. HOW TO DEFINE THE MODEL SUFFIX (NTSC or PAL model) 2 SAFETY PRECAUTIONS 2.1. GENERAL GUIDELINES 2.2. LEAKAGE CURRENT COLD CHECK 2.3. LEAKAGE CURRENT HOT CHECK (See Figure 1.) 3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES 4 HOW TO REPLACE THE LITHIUM BATTERY 4.1. REPLACEMENT PROCEDURE 5 OPERATING GUIDE 6 SERVICE NOTES 6.1. WHEN REPLACING THE MAIN C.B.A. 6.2. SERVICE POSITION 6.3. HOW TO DISCHARGE THE CAPACITOR ON FLASH TOP C.B.A. 6.4. CLEANING LENS AND LCD PANEL 7 ADJUSTMENT PROCEDURES 7.1. SERVICE FIXTURE AND TOOLS 8 ERROR CODE MEMORY FUNCTION 13 13 14 15 16 7 8 8 10 12 12 12 4 6 6 6 6 3 3 3 3 9 CONFIRMATION OF FIRMWARE VERSION 10 DISASSEMBLY PROCEDURE 10.1. DISASSEMBLY FLOW CHART 10.2. C.B.A. LOCATION 10.3. DIASSEMBLY PROCEDURE 10.4. DISASSEMBLY PROCEDURE FOR THE LENS 10.5. ASSEMBLY PROCEDURE FOR THE LENS 10.6. REMOVAL OF THE CCD 10.7. THE APPLYMENT OF GREASE METHOD 11 SCHEMATIC DIAGRAMS 11.1. OVERALL BLOCK DIAGRAM 11.2. WIRING CONNECTION DIAGRAM 11.3. FLASH TOP SCHEMATIC DIAGRAM 11.4. CCD SCHEMATIC DIAGRAM 11.5. LENS FLEX SCHEMATIC DIAGRAM 12 CIRCUIT BOARD ASSEMBLIES 12.1. CCD C.B.A. 12.2. FLASH TOP C.B.A. 12.3. LENS FLEX C.B.A. 13 EXPLODED VIEWS 13.1. FRAME & CASING SECTION 13.2. PACKING PARTS & ACCESSORIES SECTION 14 REPLACEMENT PARTS LIST 14.1. MECHANICAL REPLACEMENT PARTS LIST 14.2. ELECTRICAL REPLACEMENT PARTS LIST

Page19 20 20 20 21 25 27 30 30 31 31 32 33 33 34 35 35 36 37 38 38 40 41 41 43

2


1 INTRODUCTION1.1. INTRODUCTIONThis service manual contains technical information, which allow service personnels to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

1.2.

ABOUT LEAD FREE SOLDER (PbF)

Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB. Caution: Pb free solder has a higher melting point than standard solder, Typically the melting point is 50-70F (30-40C) higher. Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 70020F (37010C) Pb free solder will tend to splash when heated too high (about 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough.

1.3.

IMPORTANT NOTICE 1: (Other than U.S.A. and Canadian Market)

1. The service manual does not contain the following information, because of the impossibility of servicing at component level. a. Schematic diagram, Block Diagram and C.B.A. layout of Main C.B.A. b. Parts list for individual parts of Main C.B.A. When a part replacement is required for repairing Main C.B.A., replace as an assembled parts. (Main C.B.A.) 2. The following category is/are recycle module part. please send it/them to Central Repair Center. MAIN C.B.A. (VEP56021A) : Excluding replacement of Lithium Battery

3


1.4.

HOW TO DEFINE THE MODEL SUFFIX (NTSC or PAL model)

There are six kinds of DMC-LS1, regardless of the colours. DMC-LS1S DMC-LS1PP DMC-LS1EB/EG/EGM/GN DMC-LS1GC/SG DMC-LS1GT DMC-LS1PL/GK (DMC-LS1S is exclusively Japan domestic model.) What is the difference is that the INITIAL SETTING data which is stored in Flash ROM mounted on Main C.B.A.

1.4.1.

Defining methods:

To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.

NOTE: After replacing the MAIN C.B.A., be sure to achieve adjustment. The adjustment instruction is available at software download on the CS-Web from AVC web-site in TSN system.

4


1.4.2.

INITIAL SETTINGS:

When you replace the Main C.B.A., be sure to perform the initial settings after achieving the Adjustment, by ordering the following procedure in accordance with model suffix. Step 1. The temporary cancellation of factory setting: Set the mode dial to Normal Picture (Red camera mark). and UP of Cross key simultaneously, turn the Power on. While keep pressing Optical Image Stabilizer Step 2. The cancellation of factory setting: Set the mode dial to Playback Step 3. Turn the Power on: Set the mode dial to Normal Picture Step 4. Display the INITIAL SETTING: While keep pressing MENU and RIGHT of Cross key simultaneously, turn the Power off. (Red camera mark), and then turn the Power on. . and UP of Cross key simultaneously, turn the Power off. While keep pressing Optical Image Stabilizer

Step 5. Set the INITIAL SETTING: Select the area with pressing UP / DOWN of Cross key, and then press the RIGHT of Cross key.

The only set area is displayed, and then press the " RIGHT automatically.)

of Cross key" after confirmation. (The unit is powered off

Confirm the display of PLEASE SET THE CLOCK in English when the unit is turned on again. (For China and Taiwan market, the display shows PLEASE SET THE CLOCK in Chinese.) NOTE: The display shows SET THE CLOCK when turn the Power on again. Connect the unit to PC with USB cable and is detected as removable media. 1) As for your reference Default setting condition is given in the following table. Default setting (After INITIAL SETTINGS)a) b) c) d) e) MODEL DMC-LS1S DMC-LS1PP/PL DMC-LS1EB/EG/EGM/GC/GN/SG DMC-LS1GK DMC-LS1GT VIDEO OUTPUT NTSC NTSC PAL PAL NTSC LANGUAGE Japanese English English Chinese (simplified) Chinese (traditional) DATE Year/Month/Date Month/Date/Year Date/Month/Year Year/Month/Date Year/Month/Date REMARKS

5


2 SAFETY PRECAUTIONS2.1. GENERAL GUIDELINES1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturers specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design without permission of manufacturer. 2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing. 3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

2.3.

LEAKAGE CURRENT HOT CHECK (See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1. 3. Use an AC voltmeter, with 1 k/V or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

2.2.

LEAKAGE CURRENT COLD CHECK

1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1 M and 5.2 M. When the exposed metal does not have a return path to the chassis, the reading must be infinity.

6


3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICESSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).

7


4 HOW TO REPLACE THE LITHIUM BATTERY4.1. REPLACEMENT PROCEDURE1. Remove the MAIN C.B.A. (Refer to Disassembly Procedures.) 2. Remove the Lithium battery (Ref. No. Z9101 at foil side of MAIN C.B.A.) and then replace it into new one.

NOTE: This Lithium battery is a critical component. (Type No.: ML-614S/ZT Manufactured by Matsushita Battery Industrial Co.,Ltd.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in requirement designed specifically for its use. Replacement batteries must be of same type and manufacture. They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.

8


NOTE: Above caution are also applicable for below batteries which is for DMC-LS1 all series, as well. 1. AA Oxyride batteries 2. AA Alkaline batteries 3. AA Rechargeable Ni-MH (nickel-metal hydride) batteries

9


5 OPERATING GUIDE

10


11


6 SERVICE NOTES6.1. WHEN REPLACING THE MAIN C.B.A.After replacing the MAIN C.B.A., be sure to achieve adjustment. The adjustment instruction is available at software download on the CS-Web from AVC web-site in TSN system, together with Maintenance software.

6.2.No. 1 2 3 4 5

SERVICE POSITIONParts No. VFK1582A2125 VFK1951 VFK1870 VFK1950 VFK1576DC202 Table S1 Extension Cable List Connection FP9002 (MAIN) - CCD UNIT FP9001 (MAIN) - LENS UNIT PP9001 (MAIN) - PS8001 (FLASH TOP) FP9003 (MAIN) - LCD UNIT P9001 (MAIN) - LCD BACKLIGHT Form 21PIN 0.5 FFC 39PIN 0.3 FFC 30PIN B to B 33PIN 0.3 FFC 2PIN CABLE

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.

NOTE: When the Main C.B.A. is energized, be sure to connect the LCD backlight connector (P9001) to the Main C.B.A.. If the Main C.B.A. is energized that the LCD backlight connector (P9001) is opened, it may be caused to the case not only the power does not turn on but also transisitor (Q1070) is broken.

CAUTION 1. Be sure to discharge the capacitor for flash, which is connected with FLASH TOP C.B.A. (Refer to HOW TO DISCHARGE THE CHARGING CAPACITOR ON FLASH TOP C.B.A..)

12


6.3.

HOW TO DISCHARGE THE CAPACITOR ON FLASH TOP C.B.A.

CAUTION: 1. Be sure to discharge the capacitor on FLASH TOP C.B.A.. 2. Be careful of the high voltage circuit on FLASH TOP C.B.A. when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and Remove the necessary parts/unit. 2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k /5W). (an equivalent type of resistor may be used.) 3. Put the resistor between both terminals of capacitor on FLASH TOP C.B.A. for approx. 5 seconds. 4. After discharging, confirm that the capacitor voltage is lower than 10V using a voltmeter.

6.4.

CLEANING LENS AND LCD PANEL

Do not touch the surface of lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: A lens cleaning paper and lens cleaner are available at local camera shops and market place.

13


7 ADJUSTMENT PROCEDURESEven if the MAIN C.B.A. is replaced as a unit, it must be achieved the adjustment and factory setting. The adjustment in this unit is separated two types as shown below. The adjustment instruction is available at "Software download" on the CS-Web from AVC" web-site in "TSN System". 1. Main unit adjustment: All adjustments except for LCD adjustment. This unit mounts the adjustment software for main unit, it wouldnt need the connection between the PC and this unit with USB cable. 2. LCD adjustment: Adjustment for LCD. It need the connection between the PC and this unit with USB cable. The adjustment instruction is available at "Software download" on the CS-Web from AVC" web-site in "TSN System", together with maintenance software.

14


7.1.

SERVICE FIXTURE AND TOOLS

The following Service Fixture and tools are used for checking and servicing this unit.

15


8 ERROR CODE MEMORY FUNCTION1. General description This unit is equipped with history of error code memory function, and can be memorized 32 error codes in sequence from the latest. When the error is occurred more than 32, oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off. 2. How to display The error code can be displayed by the following procedure: Before perform the error code memory function, connect the AC adaptor or insert the battery. Since this unit has built-in memory, this error code memory function can be performed without inserting SD card. 1. The temporary cancellation of factory setting: Set the mode dial to Normal Picture 2. The display of error code: Press Optical Image Stabilizer , MENU and LEFT of Cross key simultaneously with the step 1 condition. The display is changed as shown below when the above buttons is pressed simultaneously. Normal display Error code display Operation history display Normal display ..... (Red camera mark). While keep pressing Optical Image Stabilizer and UP of Cross key simultaneously and hold them, turn the Power on.

Example of Error Code Display

3. The change of display: The error code can be memorized 32 error codes in sequence, however it is displayed 5 errors on the LCD. Display can be changed by the following procedure: " UP or DOWN or RIGHT of Cross key": It can be scroll up or down one. of Cross key": It can be display last 5 error or another 5 error. " LEFT

4. How to read the error code: One error code is displayed for 8 bit, the contents of error codes is indicated the table as shown below.

16


Attribute LENS

Main item Lens drive

Sub item OIS

C.B./Zoom

Zoom

Focus

Lens

Adj.History

OIS

Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) 1800 1000 PSD (X) error. Hall element (X axis) position detect error in OIS unit. OIS Unit 2000 PSD (Y) error. Hall element (Y axis) position detect error in OIS unit. OIS Unit 3000 GYRO (X) error. Gyro (IC7102: X axis) detect error on Main C.B.A.. IC7102 (Gyro element) or IC6001 (VENUS PLUS) 4000 GYRO (Y) error. Gyro (IC7101: Y axis) detect error on Main C.B.A.. IC7101 (Gyro element) or IC6001 (VENUS PLUS) 5000 MREF error (Reference voltage error). IC7002 (LENS drive) or IC6001 (VENUS PLUS) 6000 Drive voltage (X) error. VENUS PLUS AD value error, LENS Unit, LENS flex breaks etc. 7000 Drive voltage (Y) error. VENUS PLUS AD value error, LENS Unit, LENS flex breaks etc. 0100 HP Low detect error (C.B. encoder (full retract) always Low detect). FP9001-(23) signal line or IC6001 (VENUS PLUS) 0200 HP High detect error (C.B. encoder (full retract) always High detect). FP9001-(23) signal line or IC6001 (VENUS PLUS) 0300 ENC1 detect error (C.B. motor encoder detect error). FP9001-(3) signal line or IC6001 (VENUS PLUS) 0400 ENC2 detect error (C.B. motor encoder detect error). FP9001-(5) signal line or IC6001 (VENUS PLUS) 0010 HP Low detect error (Zoom encoder always Low detect error). FP9001-(3, 5) signal line or IC6001 (VENUS PLUS) 0020 HP High detect error (Zoom encoder always High detect error). FP9001-(3, 5) signal line or IC6001 (VENUS PLUS) 0030 ENC1 detect error (Zoom encoder detect error). FP9001-(3) signal line or IC6001 (VENUS PLUS) 0040 ENC2 detect error (Zoom encoder detect error). FP9001-(5) signal line or IC6001 (VENUS PLUS) 0001 HP Low detect error (Focus encoder always Low detect error). FP9001-(23) signal line or IC6001 (VENUS PLUS) 0002 HP High detect error (Focus encoder always High detect error). FP9001-(23) signal line or IC6001 (VENUS PLUS) 1801 0000 Power ON time out error. Lens drive system 1802 0000 Power OFF time out error. Lens drive system 1900 2000 OIS adj. Yaw direction amplitude error (small) 3000 OIS adj. Pit direction amplitude error (small) 4000 OIS adj. Yaw direction amplitude error (large) 5000 OIS adj. Pit direction amplitude error (large) 6000 OIS adj. MREF error 7000 OIS adj. time out error 8000 OIS adj. Yaw direction off set error 9000 OIS adj. Pit direction off set error A000 OIS adj. Yaw direction gain error B000 OIS adj. Pit direction gain error C000 OIS adj. Yaw direction position sensor error D000 OIS adj. Pit direction position sensor error E000 OIS adj. other error

17


Attribute HARD

Main item VENUS A/D FLASH ROM (EEPROM Area) SYSTEM

SOFT

CPU

Card

CPU, ASIC hard

Memory

Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) Flash 2000 0000 Flash charging error. IC6001-(13) signal line or Flash charging circuit FLASH ROM 2B00 0001 EEPROM read error (EEPROM IC6002 (FLASH ROM) Area) 0002 EEPROM write error IC6002 (FLASH ROM) RTC 2C00 0001 SYSTEM IC initialize failure error Communication between IC6001 (VENUS PLUS) and IC9101 (SYSTEM) Reset 3000 0001 NMI reset | Non Mask-able Interrupt 0007 (30000001-30000007 are caused by factors) Card 3100 0001 Card logic error SD card data line or IC6001 (VENUS PLUS) 0002 Card physical error SD card data line or IC6001 (VENUS PLUS) 0003 Read error SD card data line or IC6001 (VENUS PLUS) 0004 Write error SD card data line or IC6001 (VENUS PLUS) 0005 Format error SD card data line or IC6001 (VENUS PLUS) Stop 3800 0001 Camera task finish process time out. Communication between Lens system and IC6001 (VENUS PLUS) 0002 Camera task invalid code error. IC6001 (VENUS PLUS) 0100 File time out error in recording motion image IC6001 (VENUS PLUS) 0002 File data send error in recording motion image IC6001 (VENUS PLUS) Monitor 1000 AF frame movement check time out. IC6001 (VENUS PLUS) Built-in 3900 0005 Built-in memory format error memory FLASH ROM data line or IC6001 (VENUS PLUS)

Sub item

5. How to returned to Normal Display: Turn the power off and on, to exit from Error code display mode. NOTE: The error code can not be initialized by the unit only.

18


9 CONFIRMATION OF FIRMWARE VERSIONThe Firmware version can be confirmed by ordering the following steps:. Step 1. The temporary cancellation of factory setting: Set the mode dial to Normal Picture (Red camera mark). While keep pressing Optical Image Stabilizer and UP of Cross key simultaneously. turn the power on with inserting the SD memory card which has a few photo data. Step 2. Confirm the version: Set the mode dial to Playback Press Optical Image Stabilizer CAUTION: The version information does not display if the LCD has switched to LCD with indication already. In this case, press DISPLAY to switch to LCD with indication. and then press [DISPLAY] to switch to LCD with indication. (Fig. A) and DOWN of Cross key simultaneously. (No need to keep pressing.)

(The version information is displayed on the LCD with green colour letters.) (Fig. B)

Point: The firmware version and EEPROM version can be confirmed with the information (1). The information (2), (3) are just reference.

19


10 DISASSEMBLY PROCEDURE10.1. DISASSEMBLY FLOW CHART

10.2. C.B.A. LOCATION

20


10.3. DIASSEMBLY PROCEDURENo. Item 1 Rear Case/ Front Case Unit Fig Fig. D1 Removal Card Battery 5 Screws (A) FP9003(Flex) P9001(Connector) 3 Locking tabs Rear Case Unit Front Case Unit Removal of connector 1 Screw (B) LCD Holder LCD Unit SD Plate SD Cover 3 Screws (C) PP9001(Connector) Top Case Unit 3 Screws (D) 3 Locking tabs Flash Cover Flash Top C.B.A. NOTE: (When Installing) 4 Screws (E) FP9001(Flex) FP9002(Flex) 2 Solders Main C.B.A. Removal of connector 2 Screws (F) 2 Solders Battery Case Unit 2 Screws (G) Lens Unit

10.3.1.

Removal of the Rear Case and Front Case Unit

2

LCD Unit

Fig. D2 Fig. D3

3 4

SD Cover Top Case Unit

Fig. D4 Fig. D5

5

Flash Top C.B.A.

Fig. D6

6

Main C.B.A.

Fig. D7 Fig. D8

7

Battery Case Unit

Fig. D9 Fig. D10

8

Lens Unit

Fig. D11

Fig. D1

21


10.3.2.

Removal of the LCD Unit

Fig. D2

Fig. D3

10.3.3.

Removal of the SD Cover

Fig. D4

22


10.3.4.

Removal of the Top Case Unit

10.3.5.

Removal of the Flash Top C.B.A.

Fig. D5

Fig. D6

23


Fig. D7

10.3.6.

Removal of the Main C.B.A.Fig. D9

10.3.7.

Removal of the Battery Case Unit

Fig. D8

Fig. D10

24


10.3.8.

Removal of the Lens Unit

10.4. DISASSEMBLY PROCEDURE FOR THE LENSNOTE: When Disassembling and Assembling for the Lens 1. Use lens cleaning KIT (VFK1900BK). 2. To prevent the lens from catching the dust and dirt, perform the following procedures with the CCD unit is installing. 3. Take care that the dust and dirt are not entered into the lens. 4. Do not touch the surface of lens.

10.4.1.

Removal of the Zoom Motor Unit and Master Flange Unit

1. Remove the solders (2 points). 2. Remove the lock (5 points). 3. Unscrew the 5 screws (A). 4. Remove the Zoom Motor Unit to the indicated by arrow. 5. Remove the Cover to the indicated by arrow. 6. Remove the Master Flange Unit.

Fig. D11

NOTE: (When Assembling) Confirm the contents as shown below. Condition of the screw is tightened. Assembling condition of mechanism parts (distortion, space etc.). Dust and dirt of the lens, display condition of the LCD (gradient etc.). Dust and dirt of the LCD

25


10.4.2.

Removal of the Drive/Direct Unit, 1st Lens Frame/2nd Lens Frame Move Unit

1. Push the 1st lens frame move unit to the indicated by arrow from lens side, and then remove the unit of 1st lens frame/2nd lens frame move unit from the drive/direct unit.

1. Turn the drive gear to the indicated by arrow fully.

10.4.3.1. Push the drive unit to the indicated by arrow from lens side, and then remove the unit of drive/direct unit, 1st lens frame/2nd lens frame move unit from the fixed frame unit.

Removal of the Direct Frame

26


10.4.4.

Removal of the 2nd Lens Frame Move Unit

10.5. ASSEMBLY PROCEDURE FOR THE LENS10.5.1. Phase alignment of the Direct Frame and Drive Frame Unit

27


10.5.2.

Phase alignment of the Drive/Direct Unit and Fixed Frame

28


10.5.3.

Assembly for the Zoom Motor Unit and Master Flange Unit

29


10.6. REMOVAL OF THE CCDTo prevent unnecessary dust being entered, do not remove the CCD Unit except for servicing. - Trox driver (T3): VFK1755

10.7. THE APPLYMENT OF GREASE METHODThe grease apply point of lens unit are as follows. Apply grease additionally in the specified position if necessary. lead screw, Nut Grease: VFK1850 (Furoyl type) Amount of apply: 2 - 4 mg Guide pole S and Guide pole L Grease: VFK1829 Amount of apply: 2 - 4 mg

30


11 SCHEMATIC DIAGRAMS11.1. OVERALL BLOCK DIAGRAMOVERALL BLOCK DIAGRAM

IC3101 CCD4 MEGA PIX

IC3004 PRE PROCESSCDS,AGC,A/D, TG

IC6003 SDRAM/128M-bit

OIS UNIT

ZOOM

IRIS (ND)

SHUTTER

FOCUSSD CARD

IC3002 V-DRIVE

IC7002 MOTOR DRIVE, OIS DRIVE& PRE PROCESS IC2001 VIDEO AMP

DIGITAL/ V OUT TERMINAL

FLASH

IC6001 VENUS PLUSCAMERA PROCESS J-PEG COMP/EX PANDS MEDIA I/F USB I/F MAIN MICROPROCESSOR OIS CONTROL LENS DRIVE LCD DRIVE

REAR OPERATION UNIT

COLOR LCD PANEL2.0" PANEL

IC9101 SYSTEM IC

X9101

IC6002 FLASH ROM/ 128M-bit

TOP OPERATION UNIT

DC IN/EXT. TERMINAL

IC1001 POWER(POWER SUPPLY) BATTERY

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG OVERALL BLOCK DIAGRAM

31

11.2. WIRING CONNECTION DIAGRAM

FLASH TOP C.B.A. (COMPONENT SIDE)PS8001


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

UNREG UNREG UNREG UNREG UNREG GND UNREG GND UNREG GND UNREG GND TELE WIDE D GND OIS SW SHUTTER 0 SHUTTER 1 POWER ON

ST TRG 5V STB PWM OUT STB CHG LV STB SAFE NC A GND BUZZER BUZZER R KEY IN3 KEY IN2 FRAME GND FRAME GND FRAME GND FRAME GND

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

CCD UNIT LENS UNITFP9002 FP9003 FP9001 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 VSS POCB CS SCK HSYNC D05 D03 D01 NC VBC COMDC VGH C2+ VGL C1+ VVCOM

322 1 BL L BL H

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 Z1 LEDCNT Z2 LEDCNT Z2 ENC VCC ZM1 ZM2 ZM2 IRIS1 SHUT2 SHUT1 IRIS2 FENC VCC Y VO+ X VO+ X VOY DRV+ X DRV+ Y VOFBP FAN

Z1 ENC VCC Z1ABS Z2ABS ZM1 ZM1 ZM2 IRIS1 SHUT2 SHUT1 IRIS2 F LEDCNT FABS Y VH+ X VH+ X VHY DRVX DRVY VHFBN FAP

33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1

VCOM TEST BLON DI VSYNC CLK D04 D02 D00 NC VSH VDD VDC1 C2C1COMOUT VSS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

VH V1 [OV1] V2 [OV2] V3/V3A [OV3] V6/V3B [OV5] V4 [OV4] V5A [OV7] V5B [OV8] V6 [OV6] VL BSUB SUB HL CCD GND H1 H2 CCD GND R GUARD1 CCDOUT GUARD1

PP9001

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

UNREG UNREG UNREG UNREG UNREG GND UNREG GND UNREG GND UNREG GND TELE WIDE D GND OIS SW SHUTTER 0 SHUTTER 1 POWER ON

ST TRG 30 5R0V 29 28 STB PWM OUT 27 STB CHG LV STB SAFE 26 NC 25 A GND 24 BUZZER 23 BUZZER R 22 KEY IN3 21 KEY IN2 20 19 FRAME GND 18 FRAME GND 17 FRAME GND 16 FRAME GND

MAIN C.B.A. (FOIL SIDE)

P9001

: (COMPONENT SIDE)

LCD UNIT

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG WIRING CONNECTION DIAGRAM


11.3. FLASH TOP SCHEMATIC DIAGRAMFLASH TOP SCHEMATIC DIAGRAMOIS SW

11.4. CCD SCHEMATIC DIAGRAMCCD SCHEMATIC DIAGRAMPOSITIVE VOLTAGE LINE NEGATIVE VOLTAGE LINE

POSITIVE VOLTAGE LINEZOOM CONTROL SW S8003 ESE23F101 4 3 2 1 CL8013 CL8014

G

S8004 K0F111A00472 4 3 2 1 CL8019

E21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 VH V1 [OV1] V2 [OV2] V3A [OV3] V3B [OV5] V4 [OV4] V5A [OV7] V5B [OV8] V6 [OV6] VL BSUB SUB HL CCD GND H1 H2 CCD GND R CCD GND CCDOUT CCD GND

TL8002 LAMP[-]

TL8003 LAMP[+] CL8021 D8002 B0HCMP000006

C3101 1

T8001 C8002 G5DYA0000100 D8003 B0HCGR000004 0.033 4 2 D8004 B0HCGR000004 C8008 10 3 1 C8005 10

CL8001 PS8001 K1KB30AA0116 1 UNREG 2 UNREG 3 UNREG 4 UNREG 5 UNREG GND 6 UNREG GND 7 UNREG GND 8 UNREG GND 9 TELE 10 WIDE 11 D GND 12 OIS SW 13 SHUTTER 0 14 SHUTTER 1 15 POWER ON 16 FRAME GND 17 FRAME GND 18 FRAME GND 19 FRAME GND 20 KEY IN2 21 KEY IN3 22 BUZZER R 23 BUZZER 24 A GND 25 NC 26 STB SAFE 27 STB CHG LV 28 STB PWM OUT 29 5V 30 ST TRG

C3103 2.2

F

TL8001 R8006 1M 1 C8006 0.033

C8003 300V100

C8004 1000P

C8010 10 CL8005

D

TO MAIN (SENSOR) CIRCUIT (FP9002)

3 2

CL8003

L8001 G5FYA0000004

Q8009 B1DFCG000010R8032 1M (FLASH DRIVE) 0 3 2.8 2.8 2 1

R8004 68 R8021 100K CL8018

VSUB

E

4

3

2

1 R8033 1M 4 0 CL8009 5 6 2.8 2.8 CL8020

Q8001 B1JBLP000008(LAMP DRIVE) 5 6 7 0 8

C

IC3101V5A V5B

V3B

(CCD IMAGE SENSOR)V6

BSUB

V3A

VPT

V4

V2

TP8002 TP8001 CL8017

V1

1

2

3

4

5

6

7

8

R8013 15K 0 0 8 7 0 6 0 5 CL8011

D

Q8002 B1DFGC000003(FLASH DRIVE) 1 2 3 0 R8003 0 0 4 OUT Y GND 3 IN A 0 2 5.0 5 VCC IN B 1 CL8008 CL8004 CL8010 4

B

V0

VDD

PW

H1

HL

RG

0

0

0

0

TO MAIN (DIGITAL/ SYSTEM CONTROL) CIRCUIT (PP9001)

R3108 1M

C3104 0.01

18H2

17

16

15

14

13

12

11

10

9

R3105 0

Q3101 2SC4627J0L(CCD AMP) R3101 33

IC8001 C0ZBZ0001011 C(ST TRG AMP) 5.0

A

R3102 2200

CL8006

CL8002

C8001 1

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG CCD SCHEMATIC DIAGRAM

MODE SW S8005 K0G188A00002 R8001 2400 SHUTTER SW S8001 K0F212A00001 5 7 CL8007 C 9 8 1 2 3 R8009 8200 1 2 1 3 6 4 CL8012 3

1

2

3

4

5

POWER SW S8002 K0D112B00071 OFF ON

B

R8010 8200

R8008 4300

6

5

4

AR8011 4300 R8012 2400 CL8016 CL8015

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG FLASH TOP SCHEMATIC DIAGRAM

1

2

3

4

5

6

NOTE: (When Replacing) The following component are not mounted on the Flash Top C.B.A. which is supplied as a replacement. Be sure to put the following component when replacing the Flash Top C.B.A. as a unit. Ref No. L8001 (Transformer), Ref No. C8003 (E. capacitor)

33


11.5. LENS FLEX SCHEMATIC DIAGRAM

LENS FLEX SCHEMATIC DIAGRAMG

POSITIVE VOLTAGE LINE

Z1 ENC VCC Z1 LED CNT Z1 ABS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

A1 A2 A3 B1 B2 B3 C1

PHOTO SENSOR

A ZOOM ENCODER 1 B ZOOM ENCODER 2

F

Z2 LED CNT Z2 ABS Z2 ENC VCC ZM1(+) ZM1(+) ZM1(+) ZM2(-) ZM2(-)

DC MOTOR

C ZOOM MOTOR UNIT

E

ZM2(-) IR+ IR+ SHSHSH+

C2 D1

E1

DC SOLENOID (IRIS)

D SHUTTER UNIT

D

TO MAIN (LENS DRIVE) CIRCUIT (FP9001)

SH+ IRIRLED CNT ENC VCC ABS YVO+ YVH+ XVO+

E2 D2

DC SOLENOID (SHUTTER)

E SHUTTER UNIT

F1 F2 F3 G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 H1 H2 H3 H4

PHOTO SENSOR

F CO. BARREL ENCODER

(FULL RETRACT)

C

XVH+ XVOXVHYDRV+ YDRVXDRV+ XDRV-

HALL SENSOR (Y)

DRIVE COIL (Y) G OIS UNIT

DRIVE COIL (X) HALL SENSOR (X)

B

YVOYVHFBP FBN FAN FAP

COIL STEPPING MOTOR COIL H FOCUS MOTOR UNIT

A

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG LENS FLEX SCHEMATIC DIAGRAM

1

2

3

4

5

6

34


12 CIRCUIT BOARD ASSEMBLIES12.1. CCD C.B.A.(FOIL SIDE)E

(COMPONENT SIDE)ADDRESS INFORMATION CCD C.B.A. Integrated Circuit IC3101 B-2

Transistor Q3101 Q3102 B-1 C-2

Capacitor C-2 C3101 C-2 C3103 A-2 C3104 Resistor R3101 R3102 R3103 R3104 R3105 R3106 R3107 R3108 B-1 B-1 B-3 B-3 B-1 B-3 B-3 A-2

D

C

B

A

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG CCD C.B.A.

1

2

3

4

5

6

35


12.2. FLASH TOP C.B.A.NOTE: (When Replacing) The following component are not mounted on the Flash Top C.B.A. which is supplied as a replacement. Be sure to put the following component when replacing the Flash Top C.B.A. as a unit. Ref No. L8001 (Transformer), Ref No. C8003 (E. capacitor)ADDRESS INFORMATION FLASH TOP C.B.A. Integrated CircuitIC8001 D-2 F

H

Transistor

G

Q8001 Q8002 Q8009

C-2 D-2 D-3

F F C

Test PointCL8001 CL8002 CL8003 CL8004 CL8005 CL8006 CL8007 CL8008 CL8009 CL8010 CL8011 CL8012 CL8013 CL8014 CL8015 CL8016 CL8017 CL8018 CL8019 CL8020 CL8021 TL8001 TL8002 TL8003 TP8001 TP8002 E-4 E-2 D-3 D-3 E-5 E-2 F-1 D-3 F-4 E-4 D-2 F-4 E-4 E-4 E-4 E-4 E-4 F-3 E-4 D-2 B-4 B-3 C-3 C-4 E-5 E-5 C F C C C F F C C C F C C C C C C C C F C C C C C C

F

E

ConnectorPS8001 E-3 C

DiodeD8002 D8003 D8004 C-4 C-5 D-5 C C C

D

TransformerT8001 D-4 C

CoilL8001 C-3 C

SwitchS8001 S8002 S8003 S8004 S8005 F-2 G-2 E-1 G-1 E-2 F F F F F

C

CapacitorC8001 C8002 C8003 C8004 C8005 C8006 C8007 C8008 C8009 C8010 D-2 D-4 A-4 C-4 E-4 C-3 D-1 E-4 E-4 E-4 F C C C C C F C C C

B

ResistorR8001 R8002 R8003 R8004 R8006 R8008 R8009 R8010 R8011 R8012 R8013 R8021 R8032 R8033 D-2 D-1 D-1 D-3 C-4 D-2 D-2 E-2 E-2 E-2 D-1 D-3 D-5 D-1 F F F C C F F F F F F C C F

A

(FOIL SIDE)1 2 3

(COMPONENT SIDE)4 5

C . . . COMPONENT SIDE F . . . FOIL SIDE

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG FLASH TOP C.B.A.

6

36


12.3. LENS FLEX C.B.A.

EG OIS UNIT G6 G5 G4 G3 G2 G1 G7 G8 G9 G10 G11 G12

F C.B. ENCODER

(FULL RETRACT)

D

D, E

F2

SUTTER UNITD1 D2 F1 E2 E1 F3

C

H2 H3 H1 H4 A ZOOM ENCODER 1 C ZOOM MOTOR A1 Pin 1 Pin 39 H FOCUS MOTOR

UNITC2

UNITA2 A3 B2 B1

B

C1 B3 B ZOOM ENCODER 2

A

DMC-LS1PP/PL/EB/EG/EGM/GC/GK/GN/GT/SG LENS FLEX C.B.A.

1

2

3

4

5

6

37


13 EXPLODED VIEWS13.1. FRAME & CASING SECTION

38


39


13.2. PACKING PARTS & ACCESSORIES SECTION

40


14 REPLACEMENT PARTS LIST14.1. MECHANICAL REPLACEMENT PARTS LISTRef. No. 60 61 62 63 64 65 66 67 68 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B19 B20 B21 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 Part No. VXP2464 VXP2414 VDW1092 VXP2415 VXQ1265 VXQ1354 VMA0T19 06SSS6F3NM VXW0717 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-89 SG053-92 SG053-92 SG053-92 VHD1726 VHD1726 VHD1726 VHD1743 VHD1743 VHD1743 VHD1743 VHD1743 VHD1745 VHD1745 VHD1744 Part Name & Description Remarks 1ST LENS FRAME MOVE UNIT 2ND LENS FRAME MOVE UNIT DIRECT FRAME DRIVE FRAME UNIT FIX FRAME UNIT MASTER FLANGE UNIT COVER FOCUS MOTOR UNIT LENS UNIT (W/O CCD) SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW

14.1.1.Ref. No. 1 1 1 2 3 3 3 4 5 6 7 7 7 8 9 9 9 10 11 12 13 13 13 14 15 16 17 18 19 20 22 24 25 51 52 53 54 55 56 57 58

FRAME & CASING SECTION PARTS LISTPart No. Part Name & Description JACK COVER JACK COVER JACK COVER LED PANEL(F) REAR CASE UNIT REAR CASE UNIT REAR CASE UNIT LCD HOLDER STRAP HOLDER FRAME FRONT CASE UNIT FRONT CASE UNIT FRONT CASE UNIT REAR KNOB SD COVER SD COVER SD COVER LED PANEL SD PLATE SD SHAFT BATTERY CASE UNIT BATTERY CASE UNIT BATTERY CASE UNIT TOP CASE UNIT FLASH COVER POWER KNOB OIS KNOB FLASH UNIT LCD BACKLIGHT CONNECTOR UNIT BUZZER LCD MAIN C.B.A. FLASH TOP C.B.A. OPTICAL FILTER CCD UNIT CCD SPRING CCD SPRING CCD CUSHION RUBBER ZOOM MOTOR UNIT PHOTO SENSOR PHOTO SENSOR Remarks DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series

VKF4001 VKF4005 VKF4006 VKW3277 VYK1P09 VYK1P10 VYK1P11 VMA0T29 VMD5285 VMP8287 VYK1N47 VYK1N69 VYK1N70 VGU9797 VKF3999 VKF4003 VKF4004 VKW3276 VMA0T21 VMS7584 VYK1N49 VYK1N67 VYK1N68 VYK1P08 VGQ8421 VGU9800 VGU9801 EFN-KRT42 K1PB02000058 L0DCDD000006 L5EDDXG00001 VEP56021A VEP58012A VDL1603 VEK0H65 VMB3683 VMB3683 VMX3437 L6DA8BEC0001 B3NAA0000092 B3NAA0000092

DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series

14.1.2.Ref. No. 101 102

PACKING PARTS & ACCESSORIES SECTION PARTS LISTPart No. Part Name & Description CAMERA BAG PAKING CASE Remarks

DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series

VPF1221 VPK2972

102 102 102 102 102 103 107 (RTL) (RTL) 107 107 107 107 107

VPK3002 VPK3005 VPK2989 VPK3003 VPK2971 VPN6317 VQT0Q71 VQT0Q63 VQT0Q64 VQT0Q65 VQT0Q66 VQT0Q67

PAKING CASE PAKING CASE PAKING CASE PAKING CASE PAKING CASE PAD INSTRUCTION (ENGLISH) INSTRUCTION (GERMAN) INSTRUCTION (FRENCH) INSTRUCTION (ITALIAN) INSTRUCTION (DUTCH) INSTRUCTION (SPANISH)

DMC-LS1EB-S/ EG-S/EGM-S/ GC-S/GN-S/ GT-S/PL-S/ SG-S DMC-LS1GC-A DMC-LS1GC-T DMC-LS1GK-S DMC-LS1GK-A DMC-LS1PP-S BOOK DMC-LS1EB-S BOOK DMC-LS1EG-S BOOK DMC-LS1EG-S BOOK DMC-LS1EG-S BOOK DMC-LS1EG-S BOOK DMC-LS1EGM-S

41


Ref. No. 107 107 107 107

Part No. VQT0Q68 VQT0Q69 VQT0Q70 VQT0Q72

Part Name & Description INSTRUCTION BOOK (PORTUGUESE) INSTRUCTION BOOK (DANISH) INSTRUCTION BOOK (SWEDISH) INSTRUCTION BOOK (ENGLISH)

Remarks

Ref. No. 112 113

Part No. VFF0278-S VFC4090

Part Name & Description CD-ROM HAND STRAP

Remarks (See Notes) DMC-LS1PP-S

DMC-LS1EGM-S DMC-LS1EGM-S DMC-LS1EGM-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GK-A/ GK-S DMC-LS1GN-S DMC-LS1GT-S DMC-LS1PL-S DMC-LS1PL-S DMC-LS1PL-S DMC-LS1PP-S DMC-LS1PP-S DMC-LS1EB-S/ GK-A/GK-S/ GN-S/PP-S DMC-LS1EG-S/ EGM-S/GC-A/ GC-S/GC-T/ PL-S

14.1.3.Ref. No.

SERVICE FIXTURE & TOOLSPart No. Part Name & Description EXTENSION CABLE (30PIN-B TO B) Remarks [PP9001 (MAIN) PS8001 (FLASH TOP)] [P9001 (MAIN) - LCD BACKLIGHT] [FP9002 (MAIN) CCD UNIT] [FP9003 (MAIN) LCD UNIT] [FP9001 (MAIN) LENS UNIT]

VFK1870

107

VQT0Q73

INSTRUCTION BOOK (CHINESE (TRADITIONAL))

107

VQT0Q74

INSTRUCTION BOOK (RUSSIAN)

VFK1576DC202 EXTENSION CABLE (2PIN-CABLE) VFK1582A2125 EXTENSION CABLE (21PIN-FFC) VFK1950 EXTENSION CABLE (33PIN-FFC) EXTENSION CABLE (39PIN-FFC)

107

VQT0Q75

INSTRUCTION BOOK (ARABIC)

107

VQT0Q77

INSTRUCTION BOOK (CHINESE (SIMPLIFIED)) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (CHINESE (TRADITIONAL)) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (SPANISH) INSTRUCTION BOOK (POTUGUESE) INSTRUCTION BOOK (ENGLISH/SPANISH) INSTRUCTION BOOK (CANADIAN FRENCH) POLY BAG

VFK1951

107 107 107 107 107 107 107 108

VQT0Q78 VQT0Q76 VQT0Q60 VQT0Q61 VQT0Q62 VQT0Q58 VQT0Q59 VPF1100

ERG5SJ102 RESISTOR FOR DISCHARGING VFK1164TCM02 INFINITY LENS (WITH FOCUS CHART) VFK1164TDVLB LIGHT BOX VFK1949 TR CHART VFK1900BK LENS CLEANING KIT (BK) VFK1755 T3 TROX DRIVER VFK1829 GREASE(FOR LENS) VFK1850 GREASE(FOR FOCUS MOTOR)

108

VPF1132

POLY BAG

109 110 111 111 111 111 111 111

111

K1HA08CD0004 USB CABLE W/PLUG K1HA08CD0006 VIDEO CABLE W/PLUG VQT0Q88 INSTRUCTION BOOK(APPL.) (ENGLISH) VQT0Q84 INSTRUCTION BOOK(APPL.) (GERMAN/FRENCH) VQT0Q85 INSTRUCTION BOOK(APPL.) (ITALIAN/DUTCH) VQT0Q86 INSTRUCTION BOOK(APPL.) (SPANISH/PORTUGUESE) VQT0Q87 INSTRUCTION BOOK(APPL.) (SWEDISH/DANISH) VQT0Q89 INSTRUCTION BOOK(APPL.) (ENGLISH/ CHINESE(TRADITIONAL)) VQT0Q90 INSTRUCTION BOOK(APPL.) (ARABIC/RUSSIAN) VQT0Q91 VQT0Q92 VQT0P63 VQT0Q83 INSTRUCTION BOOK(APPL.) (CHINESE (SIMPLIFIED)) INSTRUCTION BOOK(APPL.) (ENGLISH) INSTRUCTION BOOK (APPL.) (CHINESE (TRADITIONAL)) INSTRUCTION BOOK(APPL.) (ENGLISH/SPANISH/ PORTUGUESE) INSTRUCTION BOOK(APPL.) (ENGLISH/CANADIAN FRENCH) CD-ROM

DMC-LS1EB-S DMC-LS1EG-S DMC-LS1EG-S DMC-LS1EGM-S DMC-LS1EGM-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GK-A/ GK-S DMC-LS1GN-S DMC-LS1GT-S DMC-LS1PL-S

111 111 111 111

111 112

VQT0Q82 VFF0279-S

DMC-LS1PP-S (See Notes) DMC-LS1EB-S/ EG-S/EGM-S/ GC-A/GC-S/ GC-T/GK-A/ GK-S/GN-S/ GT-S/PL-S/ SG-S

42


14.2. ELECTRICAL REPLACEMENT PARTS LIST

E.S.D. standards for Electrostatically Sensitive Devices, refer to PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES section. Definition of Parts supplier: 1. Parts marked with [MBI] in the remarks column are supplied from Matsushita Battery Industrial co., ltd. .Ref. No. Part No. Part Name & Description Remarks

Ref. No. R8006 R8008 R8009 R8010 R8011 R8012 R8013 R8021 R8032 R8033 S8001 S8002 S8003 S8004 S8005 T8001

Part No. ERJ8GEYJ105V ERJ2GEJ432X ERJ2GEJ822 ERJ2GEJ822 ERJ2GEJ432X ERJ2GEJ242 ERJ2RHD153X ERJ2GEJ104 ERJ6RED105 ERJ6RED105 K0F212A00001 VSS0534 ESE23F101 K0F111A00472 K0G188A00002

Part Name & Description M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR SWITCH SWITCH SWITCH SWITCH SWITCH CH CH CH CH CH CH CH CH CH CH 1/8W 1M 1/16W 4.3K 1/16W 8.2K 1/16W 8.2K 1/16W 4.3K 1/16W 2.4K 1/16W 15K 1/16W 100K 1/16W 1M 1/16W 1M

Remarks

K0D112B00071

G5DYA0000100 TRANSFORMER

s ------ P.C.B. LIST -----MAIN C.B.A. (RTL) C3101 C3103 C3104 Q3102 R3101 R3102 R3105 R3108

VEK0H65 ECJ2YB1A105K ECJ3VF1C225Z ECJ0EB1C103K 2SC4627JCL ERJ2RKD330 ERJ2GEJ222 ERJ2GE0R00X ERJ2GEJ105

CCD UNIT C.CAPACITOR CH 10V 1U C.CAPACITOR CH 16V 2.2U C.CAPACITOR CH 16V 0.01U TRANSISTOR NPN M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR CH CH CH CH 1/16W 1/16W 1/16W 1/16W 33 2.2K 0 1M

s

VEP56021A

s

VEP58012A

FLASH TOP C.B.A.

(RTL)

s

VEK0H65

CCD UNIT

C8003 L8001

--- INDIVIDUAL PARTS --F2A2F1010004 E.CAPACITOR 300V 100U G5FYA0000004 TRANSFORMER

s

VEP56021A

--- ELEC. COMPONENTS --MAIN C.B.A. (RTL) MISCELLANEOUS BATTERY

Z9101

ML-614S/ZT

[MBI]

s C8001 C8002 C8004 C8005 C8006 C8008 C8010 D8002 D8003 D8004

VEP58012A ECJ1VB0J105K F1K2J333A013 F1K2J102A010 F1J0J1060010 F1L2E333A002 F1J0J1060010 F1J0J1060010

FLASH TOP C.B.A. C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR CH 6.3V 1U 630V 0.033U 630V 1000P CH 6.3V 10U CH 250V0.033U CH 6.3V 10U CH 6.3V 10U

(RTL)

B0HCMP000006 DIODE B0HCGR000004 DIODE B0HCGR000004 DIODE

IC8001 C0ZBZ0001011 IC PS8001 K1KB30AA0116 CONNECTOR 30P Q8001 Q8002 Q8009 R8001 R8003 R8004 B1JBLP000008 TRANSISTOR B1DFGC000003 TRANSISTOR B1DFCG000010 TRANSISTOR ERJ3GEYJ242 M.RESISTOR CH 1/10W 2.4K ERJ6GEY0R00V M.RESISTOR CH 1/10W 0 ERJ2GEJ680 M.RESISTOR CH 1/16W 68

D0GBR00JA017 ERJ2RMJ680X

43

Documents

DSC0503007C0_A_DMC-LS1PP