DS800 BT UserManual 20120814 - dubacotech.comdubacotech.com/dimage/downs/DS800(BT)_UserManual_20120814.… · Title: Microsoft Word - DS800_BT__UserManual_20120814.doc Author: Administrator

DS-800(BT)

Pocket-size Wireless Scanner

User’s Manual

Table of Contents

Memory Mode ---------------------------------------------------------------------------3

BT Local name---------------------------------------------------------------------------3

Bluetooth mode configuration------------------------------------------------------4

Remote Mac Address------------------------------------------------------------------5

Pin Code-----------------------------------------------------------------------------------5

Bluetooth parameter configuration by software-----------------------------6

USB-HID / USB-COM Mode----------------------------------------------------------6

Memory Mode Setting-----------------------------------------------------------------7

Ext Transmission Delay-------------------------------------------------------------10

Lamp OFF Delay-----------------------------------------------------------------------10

Standby Time---------------------------------------------------------------------------11

Separator---------------------------------------------------------------------------------11

Bluetooth Mode Setting-------------------------------------------------------------12

Lamp OFF Delay-----------------------------------------------------------------------12

Connect OFF Time--------------------------------------------------------------------14

Standby Time---------------------------------------------------------------------------14

Time out----------------------------------------------------------------------------------15

Grneral Configuration Setting----------------------------------------------------17

USB-HID Keyboard Type-----------------------------------------------------------17

Transmission Gap--------------------------------------------------------------------18

Transmission Delay------------------------------------------------------------------19

Timeout----------------------------------------------------------------------------------20

Keyboard Layout Setting----------------------------------------------------------21

Bluetooth HID Dongle Keyboard Layout Setting--------------------------22

Virtual COM Type---------------------------------------------------------------------23

Time out----------------------------------------------------------------------------------23

Transmission Gap---------------------------------------------------------------------24

Transmission Delay--------------------------------------------------------------------25

System Control------------------------------------------------------------------------26

Trigger Mode-------------------- -------------------------------------------------------28

Buzzer----------------- -------------------------------------------------------------------29

Beep Volume-----------------------------------------------------------------------------29

Beep Tone-------------------------------------------------- ------------------------------30

Beep Time -------------------------------------------------------------------------------31

Standby Time---------------------------------------------------------------------------32

LED OFF Delay-------------------------------------------------------------------------33

Lamp OFF Delay-----------------------------------------------------------------------34

Good Read Time-----------------------------------------------------------------------35

Setup Timeout--------------------------------------------------------------------------36

Vibrator OFF Delay--------------------------------------------------------------------37

Double Confirm------------------------------------------------------------------------38

Global Min. / Max. Length-----------------------------------------------------------39

Global Min. Length---------------------------------------------------------------------39

Global Max. Length -------------------------------------------------------------------40

Set Data & Time-----------------------------------------------------------------------41

Symbology Settings-----------------------------------------------------------------42

UPC-A--------------- --------------------------------------------------------------------43

UPC-E---------------- -------------------------------------------------------------------44

EAN-13-----------------------------------------------------------------------------------46

EAN-8-------------------------- ----------------------------------------------------------48

Code-39------------------------------------------------------- --------------------------50

Codabar / NW7--- ---------------------------------------------------------------------52

Code-128---------------------------------------------------------------------------------54

Interleaved 2 of 5 ---------------------------------------------------------------------56

Industrial 2 of 5----- -------------------------------------------------------------------57

Matrix 2 of 5---- ------------------------------------------------------------------------58

Code 93------ -------------------- -------------------------------------------------------59

Code 11-- ------------ -------------------------------------------------------------------60

MSI / Plessey---------------------------------------------------------------------------61

UK / Plessey --------------------------------------------- -----------------------------62

Telepen-----------------------------------------------------------------------------------63

RSS (GS1 DataBar) 14---------------------------------------------------------------64

RSS (GS1 DataBar) Limited--------------------------------------------------------65

RSS (GS1 DataBar) 14 Stack-------------------------------------------------------66

RSS (GS1 DataBar) Expansion----------------------------------------------------67

RSS (GS1 DataBar) Expansion Stack ------------------------------------------68

Output Format Settings-------------------------------------------------------------69

Transmission Preamble---------------------------------------------------------------69

Transmission Postamble -------------------------------------------------------------69

Preamble Data--------------------------------------------------------------------------70

Postamble Data ------------------------------------------------------------------------71

Prefix / Suffix---------------------------------------------------------------------------72

Prefix Data-------------------------------------------------------------------------------72

Suffix Data ---------- --------------------------------------------------------------------73

Code ID / Sub Code ID--------------------------------------------------------------74

Code ID Setting------------------------------------------------------------------------74

Wait Add-On Count------- ----------------------------------------------------------76

Min. / Max. Length---------------------------------------- ---------------------------77

Min. Length------------------------------------------------------------------------------77

Max. Length -----------------------------------------------------------------------------79

Truncate Zero--------------------------------------------------------------------------81

Truncate Leading ---------------------------------------------------------------------86

Truncate Ending-----------------------------------------------------------------------89

Insert 0 Position---------------- ------------------------------------------------------92

Insert 1 Position -----------------------------------------------------------------------95

Insert 0 Data----- -----------------------------------------------------------------------98

Insert 1 Data -------------------------------------------- ------------------------------101

Hexadecimal / Decimal Table----------------------------------------------------104

ASCII Code Table--------------------------------------------------------------------105

Memory Mode

Switch from Bluetooth to Memory Mode

Send

Connect the USB cable between scanner

and PC, and scan the below “Send” barcode.

Clear Clear all barcode data in the memory

Bluetooth mode configuration Enter

End

Mode

Slave Mode : Third party Bluetooth devices ( Mode:0)

Master Mode - Third party Bluetooth devices (Mode:1)

Econnect Bluetooth dongle Mode I (Mode:2)

HID Mode - For third party Bluetooth devices (Mode:3)

iPad OSK MODE (Mode selection code:4)

Econnect Bluetooth dongle Mode II (Mode:5)

OK

BT Local name

Enter

BT Local name

OK

End

Set Local name as ‘BT Scanner’

(A) Scan “BT Module Enter” barcode

(B) Scan “BT Local name” barcode

(C) Scan parameters from Hexadecimal / Decimal

barcode table =>“4”,”2”,

“5”,”4”, “2”,”0”, “5”,”3”, “6”,”3”, “6”,”1”, “6”,”E”, “6”,”E”,

“6”,”5”, “7”,”2”→”OK”(configured as ‘BT Scanner’,

Please refer to ASCII TABLE)

(D) Scan “End” Barcode

3 4

Remote Mac Address

Enter

Remote Mac Address

OK

End

Set Remote Mac Address to 00126F006EAA

A. Scan “BT Module Enter” barcode

B. Scan “Remote Mac Address” barcode

C. Scan parameters from Hexadecimal /decimal

barcode table =>“0”, “0”,“1”,”2”, “6”,”F”, “0”,”0”,

“6”,”E”, “A”,”A”→”OK” (Set “Remote Mac Address

“ value to 00126F006EAA)

D. Scan “End” barcode

Pin Code

Enter

Pin Code

OK

End

Set Pin Code to 5678

(A) Scan “BT Module Enter” Barcode

(B) Scan “Pin Code” Barcode

(C) Scan parameters from Hexadecimal/Decimal

table =>“5”,”6”, “7”,”8”→”OK”

(Set “Pin Code “ value to 5678)


Bluetooth parameter configuration by software

Enter

ISP

Connect scanner with PC by USB cable, and

set the scanner to ISP mode.

Scan the below barcodes step by step to set the

scanner to ISP mode.

USB-HID / USB-COM Mode

Enter

USB-HID

USB-COM

Before scan the barcode, make sure the scanner and the Bluetooth Dongle is in paired status.

5 6

Memory Mode Setting Enter

Header Transmission

Disabel

*Enabel

Date & Time Transmission

Disabel

*Enabel

Reject Same

End

*Disabel

Enabel

Good Read Beep

Disabel

*Enabel

Good Read Vibrator

*Disabel

Enabel

Time Format

*hh：mm：ss

hh：mm

7 8

Date Format

*yyyy/mm/dd

mm/dd/yyyy

yy/mm/dd

mm/dd/yy

yyyy-mm-dd

mm-dd-yyyy

yy-mm-dd

mm-dd-yy

dd/mm/yyyy

dd/mm/yy

dd-mm-yyyy

dd-mm-yy

Enter

End

Ext Transmission Delay

This configuration enables the delay time (time gap) setting in between

each barcode data sending to PC.

(1) Enter

(2) Ext Transmission Delay barcode

(3) Scan parameters from Hexadecimal /

Decimal table

(Range:0~250 = 0~2.5sec)

(4) OK

(5) End

Lamp Off Delay

The configuration enables the setting of duration time of scanner LED

power off.

(1) Enter

(2) Lamp Off Delay barcode


Decimal table

(Range:0~255 = 0~255sec)

(4) OK

(5) End

9 10

Standby Time Bluetooth Mode Setting

This configuration enables the time configuration for the main power

switching off after scanner LED turned off.

(1) Enter

(2) Standby Time barcode


Decimal table

(Range:0~99 = 0~99sec)

(4) OK

(5) End

Separator

This configuration enables separator setting in between date, time and

barcode data. In order for the date and time to be display in front of each

barcode data, Date & time transmission must be enabled.

(1) Enter

(2) Separator barcode


Decimal table

(Max:1digit)

(4) OK

(5) End

BT List

Enter

List

User can simply understand their Bluetooth

parameter setting by scanning the following

barcode, and use the notepad to receive the

Bluetooth parameter configuration data.

BT Default Setting

Enter

Default

User can restore the default setting for the

Bluetooth Parameter.

The configuration enables the setting of duration time of scanner LED

power on and off

Lamp Off Delay

(1) Enter

(2) Lamp Off Delay barcode


Decimal table

(Range:0~255 = 0~255sec)

(4) OK

(5) End

12 11

Enter

End

Good Read Beep

*Enabel

Disabel

Good Read Vibrator

Enabel

*Disabel

The vibration configuration if barcode reading

is successfully decoded. Note:Vibration

function is only available for the scanner with

vibrator installed.

Connect Off Time

(1) Enter

Under the Bluetooth mode, when the Bluetooth connection is

established while the scanner is not working. This configuration enables

to set the duration of scanner sleep time. (Note: Default value is 6 as

60 seconds)

(2) Connect Off Time barcode


Decimal table

(Range:0~255 = 0~42Min 30sec)

(4) OK

(5) End

Standby Time

This configuration enables the time configuration for the main power

switching off after scanner LED turned off.

(1) Enter



Decimal table

(Range:0~99 = 0~99sec)

(4) OK

(5) End

Data & Time Transmission

*Enabel

Disabel

Under Bluetooth mode, user can enabled/

disable the time stamp function in front of the

barcode data.

Time Format

*hh：mm：ss

hh：mm

Time format configuration, in order for the time

stamp to be display in front of each barcode

data, Date and Time Transmission must be

enabled and configure the following formats:

13 14

Timeout

The timeout setting for the handshaking acknowledgment from the host

PC, if scanner did not receive acknowledgement from the host PC, the

warning sound will be active. This function is particular useful for some

applications which host PC takes longer response time.

(1) Enter

(2) Timeout barcode


Decimal table

(Range:0~99 = 0~99sec)

(4) OK

(5) End

Enter

End

Date Format

*yyyy/mm/dd

mm/dd/yyyy

yy/mm/dd

mm/dd/yy

yyyy-mm-dd

mm-dd-yyyy

yy-mm-dd

mm-dd-yy

dd/mm/yyyy

dd/mm/yy

dd-mm-yyyy

dd-mm-yy

16 15

Enter

End

Grneral Configuration Setting

Factory Default

Version

Abort Setting

USB-HID Keyboard Type

USB-HID Keyboard

Caps lock

Auto

Alt+Keypad

*Caps lock off

Caps lock On

Transmission Gap

(1) Enter

(2) Transmission gap barcode


Decimal table

(Range:0~250 = 0~0.25sec)

This is the delay time setting between each barcode data characters. If

the delay time setting is too high, the application program may not be

able to receive all the barcode data characters due to transmission

speed.

(4) OK

(5) End

17 18

Transmission Delay

The delay time settings between the barcode data output, this enables

the user to set the output timing between each barcode data scanned.

(1) Enter

(2) Transmission Delay barcode


Decimal table

(Range:0~250 = 0~0.25sec)

(4) OK

(5) End

Timeout

The timeout setting for the handshaking acknowledgment from host PC,

if scanner did not receive acknowledgement from the host PC, the

warning sound will be active. This function is particularly useful for some

application which host PC takes longer response time.

(1) Enter

(2) Timeout barcode


Decimal table

(Range:0~255 = 0~4min15sec)

(4) OK

(5) End

19 20

Enter Enter

End End

Keyboard Layout Setting

*US

UK

JP

FR

GR

IT

SP

PO

Bluetooth HID Dongle Keyboard Layout Setting

*US

UK

JP

FR

GR

IT

SP

PO

22 21

Enter

End

Virtual Com Type

Transmission Gap

This is the delay time setting between each barcode data characters. If

the delay time setting is too high, the application program may not be

able to receive all the barcode data characters due to transmission

speed.

(1) Enter

(2) Transmission gap barcode


Decimal table

(Range:0~250 = 0~0.25sec)

(4) OK

(5) End

Timeout

The timeout setting for the handshaking acknowledgment from host PC,

if scanner did not receive acknowledgement from the host PC, the

warning sound will be active. This function is particularly useful for some

application which host PC takes longer response time.

(1) Enter

(2) Timeout barcode


Decimal table

(Range:0~250 = 0~0.25sec)

(4) OK

(5) End

23 24

Transmission Delay

The delay time settings between the barcode data output, this enables

the user to set the output timing between each barcode data scanned.

(1) Enter

(2) Transmission Delay barcode


Decimal table

(Range:0~250 = 0~0.25sec)

(4) OK

(5) End

System Control

Power On Music

*Enabel

Disabel

Good Read Beep

*Enabel

Disabel

Good Read Vibrator

Enabel

*Disabel

Transmission Length

Enabel

*Disabel

Enter

End 26 25

Enter Enter

End End

Force Caes

*None

Inverse

Lowercase

Uppercase

This configuration enables to convert all output

digits to be same printing-case; even one

barcode may have two kinds of case

Transmission Code ID

Enabel

*Disabel

When scanning the barcode, User might want

to know the symbology of the barcode ID, This

configuration enables to display the Code ID or

Sub Code ID.

Code ID Position

After

*Before

When “Transmission Code ID” is “Enable”, user

can configure the output position of Code ID or

Sub Code ID (Before / After).

Transmission Code Name

Enabel

*Disabel

This configuration enables to show the barcode

symbology name. Symbology name will be

showing in front of barcode data.

Trigger Mode

Good Read Off

Momentary

Alternate

Timeout Off

Continue

Test

27 28

Buzzer

(1) Enter

Beep Volume

Beep volume configuration enables to configure the volume of the Beep

sound

(2) Beep Volume barcode


Decimal table

(Range:1~10)

(4) OK

(5) End

Beep Tone

Beep Tone configuration enables to configure the frequency of beep

sound.

(1) Enter

(2) Beep Tone barcode


Decimal table

(Range:1~50 = 100~5000HZ)

(4) OK

(5) End

30 29

Beep Time

Beep time configuration enables to configure the duration of the beep

sound.

(1) Enter

(2) Beep Time barcode


Decimal table

(Range:0~250 = 0~2.5Sec)

(4) OK

(5) End

This function enables to set the duration time to turn off the main

power of the scanner after scanning LED turns off.

(1) Enter


Decimal table

(Range:0~99= 0~99Sec)


(4) OK

(5) End

Standby Time

31 32

When the barcode is successfully read and decoded, The Green LED

indicator will be shown; user can configure the duration time for LED

indicator. (Note: when the configuration set as “0” or “00”, the

Green LED will be always ON)

(1) Enter


Decimal table

(Range:0~250 = 0~2.5Sec)

(2) LED OFF Delay barcode

(4) OK

(5) End

This enables to configure the duration time for scanning LED power off,

the scanning LED will automatically turn off if duration time elapsed. This

setting is only available when the trigger mode is set as” Good read off”

or “Timeout Off”

(1) Enter


Decimal table

(Range:0~250 = 0~2.5Sec)

(2) LAMP OFF Delay barcode

(4) OK

(5) End

LED OFF Delay LAMP OFF Delay

34 33

This enables to set the scanning duration time for reading the same

barcode label, this function only available when the trigger mode is set in

“Continue” or “Momentary” or “Alternate” mode.(Note: when the

configuration is set as “0” or “00”, it means, no waiting time

needed. User can scan the same barcode label without any delay

time).

(1) Enter

(2) Good Read Time barcode


Decimal table

(Range:0~250 = 0~25sec)

(4) OK

(5) End

This configuration enables to set the duration of scanner configuration

time. If user does not perform any actions after scanning the “Enter”

barcode (Configuration barcode) the setting mode will automatically exit.

(1) Enter


Decimal table

(Range:0~255 = 0~4min15sec)

(2) Setup Timeout barcode

(4) OK

(5) End

Good Read Time Setup Timeout

35 36

This configuration enables to set the duration of vibrating time when the

barcode is successfully read and decoded. (Note: this configuration is

only applicable with optional purchased vibrator installed, and

Good read Vibrator function set as “Enable” Chapter: 7-3-3)

(1) Enter


Decimal table

(Range:0~250 = 0~2.5sec)

(2) Vibrator OFF Delay barcode

(4) OK

(5) End

Vibrator OFF Delay Double Confirm

This option enables the scanner to double confirm the barcode data, if

this option is enabled, the scanner will require more times to verify the

barcode data. This setting will related to the double confirm count

configuration, the more confirm counts will inhibit miss-reading

barcodes.

(1) Enter

(2) Enable

(3) *Disable

(5) End

37 38

Global Min./ Max. Length

Global Min. Length

This function enables to set the minimum barcode length, if the barcode

length is less than configured Min. length, the barcode will not be

decoded. If configured value is 0, it means no limits in min length.

(1) Enter

(2) Global Min. length barcode


Decimal table

(Range:0~64)

(4) OK

(5) End

Global Max. Length

This function enables to set the maximum barcode length, if the barcode

length is greater than configured maximum length, the barcode will not

be decoded. If configured value is 0, it means no limits in max length.

(1) Enter

(2) Global Max. length barcode


Decimal table

(Range:0~64)

(4) OK

(5) End

40 39

Set Data & Time

This function is to set the scanner time stamp, the default format is

(YYMMDDHHMM)

(1) Enter

(2) Set Data & time barcode

(3) Scan Decimal Barcode

“1”=>”2”=>”0”=>”8”=>”3”=>”0”=>”1”=>”3”=>”3”=

>”0” =>”OK”. (as 2012/8/30,13:30)

(4) OK

(5) End

Symbology Settings

UPC-A

Enter

End

Read

*Enabel

Disable

Add – on Type

*None

Add-on 2

Add-on 5

Add-on 2+5

41 42

End End

Enter Enter

Wait Add – on

Enable

*Desable

Transmission Checksum

*Enable

Desable

UPC-E

Read

*Enable

Desable

Wait Add – on

Enable

*Desable

Add – on Type

*None

Add-on 5

Add-on 2

Add-on 2+5

44 43

Enter Enter

End End

Expansion

Enable

*Desable


*Enable

Desable

EAN-13

Read

*Enable

Desable

Wait Add – on

Enable

*Desable

Add – on Type

*None

Add-on 5

Add-on 2

Add-on 2+5

45 46

Enter Enter

End End

ISBN /ISSN Conversion

Enable

*Disable


*Enable

Disable

EAN-8

Read

*Enable

Desable

Wait Add – on

Enable

*Desable

Add – on Type

*None

Add-on 5

Add-on 2

Add-on 2+5

48 47

Enter Enter

End End

Expansion

Enable

*Disable


*Enable

Disable

Code-39

Read

*Enable

Disable

Type

*Standard

Full ACSII

Code 32 Translation

*None

Code-32 with ‘A’

Code-32

49 50

Enter Enter

End End

Transmission Start / End

Enable

*Disable

Checksum Verification

Enable

*Disable


Enable

*Disable

Codabar / NW7

Read

*Enable

Disable

Start / End Symbol types

*ABCD / ABCD

ABCD / TN*E

abcd / abcd

abcd / tn*e

Same Start / End Pair

Enable

*Disable

52 51

Enter Enter

End End

Transmission Start / End

Enable

*Disable


Enable

*Disable


Enable

*Disable

Code 128

Read

*Enable

Disable

Type

*Standard

UCC-128


*Enable

Disable


Enable

*Disable

53 54

Enter

End

Connection Data

When “Type” is set “UCC-128”, you can set connection data. If the value

is configured as “Null” , it will show default value”<GS>”, if the value is

not configured “Null” will refers to ASCII table for related setting.

(1) Enter

(2) Connection data barcode

(3) Scan Hexadecimal barcode table

=>“4”,”1”,”4”,”2”,”OK” (means set

“Connection data “ value to “AB”, please

refer to ASCII Code

table)

(4) OK

(5) End

Interleaved 2 of 5

Read

Enable

*Disable


Enable

*Disable


Enable

*Disable

56 55

Enter Enter

End End

Industrial 2 of 5

Read

Enable

*Disable


Enable

*Disable


Enable

*Disable

Matrix 2 of 5

Read

Enable

*Disable


Enable

*Disable


Enable

*Disable

57 58

Enter Enter

End End

Code 93

Read

Enable

*Disable


Enable

*Disable


Disable

*Two

One

Code 11

Read

Enable

*Disable


Enable

*Disable


Disable

*Two

One

60 59

Enter Enter

End End

MSI / Plessey

Read

Enable

*Disable


Enable

*Disable


Disable

Mod 10 /10

Mod 11 /10

*Mod 10

UK / Plessey

Read

Enable

*Disable

Verify Checksum

Enable

*Disable


Enable

*Disable

61 62

Enter Enter

End End

Telepen

Read

Enable

*Disable


*Enable

Disable

Type

Numeric

*Auto switching

ASCII


Enable

*Disable

RSS (GS1 DataBar) 14

Read

Enable

*Disable

Code Mark

Enable

*Disable

Application ID

Enable

*Disable


Enable

*Disable

64 63

Enter Enter

End End

RSS (GS1 DataBar) Limited

Read

Enable

*Disable

Code Mark

Enable

*Disable

Application ID

Enable

*Disable


Enable

*Disable

RSS (GS1 DataBar) 14 Stack

Read

Enable

*Disable

Code Mark

Enable

*Disable

Application ID

Enable

*Disable


Enable

*Disable

65 66

Enter Enter

End End

RSS (GS1 DataBar) Expansion

Read

Enable

*Disable

Code Mark

Enable

*Disable

Application ID

Enable

*Disable


Enable

*Disable

RSS (GS1 DataBar) Expansion Stack

Read

Enable

*Disable

Code Mark

Enable

*Disable

Application ID

Enable

*Disable


Enable

*Disable

68 67

Enter Output Format Settings

Preamble / Postamble

Transmission Preamble

*Enable

Disable

Transmission Postamble

*Enable

Disable

Preamble Data

There is control digits can be programmed as Preamble. It will be

appended automatically when each barcode is decoded. The string of

Preamble data will be before the barcode data.

(1) Enter

(2) Preamble data barcode

(3) Scan Hexadecimal Barcode(Max:8 digits)

(4) OK

(5) End

End 69 70

Postamble Data

Generally, your application needs to append a carriage return character

to finish data transmission. Or you may set the Postamble to be Disable

to have your application without any control characters appended after

data transmission. The factory default of Postamble Data is <CR> and

<LF>. The string of Postamble data will be behind the barcode data.

(1) Enter

(2) Postamble data barcode


(4) OK

(5) End

Prefix / Suffix

Prefix Data

Appending characters behind the preamble data and before the barcode

data, prefix data can be configured. The string of prefix data will be

behind the preamble data and before the barcode data. The prefix data

can be set up to 8 characters. Please refer to the string output flow chart.

(1) Enter

(2) Prefix data barcode


(4) OK

(5) End

71 72

Suffix Data

Appending characters behind the barcode data and before the

postamble data., suffix data is configurable. The string of suffix data will

be behind the barcode data and before the postamble data. The suffix

data can be set up to 8 characters. Please refer to sting output flow

chart.

(1) Enter

(2) Suffix data barcode


(4) OK

(5) End

Code ID / Sub Code ID

Code ID Setting

Code ID for UPC-A

Code ID for EAN-13

Code ID for Code-39

Code ID for Code-128

Code ID for Industrial 2 of 5

Example：

Change UPC-A Code ID to ”B”

(A) Scan “Enter” Barcode

(B) Scan “Code ID for UPC-A” Barcode

(C) Scan parameters from Hexadecimal Barcode table 　“4”　”2”　

“OK“

(This means set UPC-A Code ID to “B”), please refer to ASCII table.


Enter

End 74 73

Code ID for Code-93

Code ID for MSI / Plessey

Code ID for UPC-E

Code ID for EAN-8

Code ID for Codabar / NW7

Code ID for Interleaved 2 of 5

Code ID for Matrix 2 of 5

Code ID for Code-11

Code ID for UK / Plessey

Wait Add-On Count

This setting is used for WPC add-on code, such as UPC-A, UPC-E,

EAN-13 and EAN-8. The WPC code must be decoded first, then Add-on

code. Add-on code may not be decoded with WPC at the same time.

Therefore, you can set wait add-on count to force the add-on code must

be output with WPC code together.

(1) Enter

(2) Wait Add-on Count barcode

(3) Scan Hexadecimal Barcode

(4) OK

(5) End

75 76

Enter Enter

End End

Min. / Max. Length

Min. Length

Procedure：

(A) Scan “Enter” barcode

(B) Scan “Min. Length” barcode

(C) Scan parameters from Hexadecimal/ decimal table

(D) Scan “OK“ barcode

(E) Scan “End” barcode

Min. Length for Code-39


Min. Length for Industrial 2 of 5


Min. Length for MSI / Plessey

Min. Length for Telepen

Min. Length for Codabar / NW7

Min. Length for Interleaved 2 of 5

Min. Length for Matrix 2 of 5


Min. Length for UK / Plessey

78 77

Enter Enter

End End

Max. Length

Procedure：


(B) Scan “Max. Length” barcode




Max. Length for Code-39


Max. Length for Industrial 2 of 5


Max. Length for MSI / Plessey

Max. Length for Telepen

Max. Length for Telepen

Max. Length for Codabar / NW7

Max. Length for Interleaved 2 of 5

Max. Length for Matrix 2 of 5


Max. Length for UK / Plessey

79 80

Enter Enter

End End

Truncate Zero

When the barcode leading have “0”, you can configured this function to

truncate all leading "0" of barcode.

Example: Barcode "00054321"=>Output "54321"

Truncate Zero for UPC-A

Enable

*Disable

Truncate Zero for EAN-13

Enable

*Disable

Truncate Zero for Code-39

Enable

*Disable

Truncate Zero for UPC-E

Enable

*Disable

Truncate Zero for EAN-8

Enable

*Disable

Truncate Zero for Codabar / NW7

Enable

*Disable


Enable

*Disable

82 81

Enter Enter

End End

Truncate Zero for Industrial 2 of 5

Enable

*Disable


Enable

*Disable

Truncate Zero for MSI / Plessey

Enable

*Disable

Truncate Zero for Interleaved 2 of 5

Enable

*Disable

Truncate Zero for Matrix 2 of 5

Enable

*Disable


Enable

*Disable

Truncate Zero for UK / Plessey

Enable

*Disable

Truncate Zero for Telepen

Enable

*Disable

83 84

Enter Enter

End End

Truncate Zero for RSS(GS1 DataBar) Limited

Enable

*Disable

Truncate Zero for RSS(GS1 DataBar) Expansion

Enable

*Disable

Truncate Zero for RSS(GS1 DataBar) 14

Enable

*Disable

Truncate Zero for RSS(GS1 DataBar) 14 Stack

Enable

*Disable

Truncate Leading

The leading characters of barcode data will be truncated when these

values are set to non zero. It will be output nothing except beeps if the

truncate value is more than barcode data digits or overlap with the

Ending. The maximum value of truncate digits is 15.

Procedure


(B) Scan “Truncate Lead” barcode




Truncate leading for UPC-A

Truncate leading for EAN-13

Truncate leading for Code-39


Truncate leading for Industrial 2 of 5

86 85

Enter Enter

End End


Truncate leading for MSI / Plessey

Truncate leading for UPC-E

Truncate leading for EAN-8

Truncate leading for Codabar / NW7

Truncate leading for Interleaved 2 of 5

Truncate leading for Matrix 2 of 5


Truncate leading for UK / Plessey

Truncate leading for Telepen

Truncate leading for RSS(GS1 DataBar) Limited

Truncate leading for RSS(GS1 DataBar) Expansion

Truncate leading for RSS(GS1 DataBar) 14

Truncate leading for RSS(GS1 DataBar) 14 Stack

Truncate leading for RSS(GS1 DataBar) Expansion Stack

87 88

Enter Enter

End End

Truncate Ending

The ending characters of barcode data will be truncated when these

values are set to non zero. It will be output nothing except beeps if the

truncate value is more than barcode data digits or overlap with the

leading. The maximum value of truncate digits is 15.

Procedure


(B) Scan “Truncate ENd” barcode




Truncate Ending for UPC-A

Truncate Ending for EAN-13

Truncate Ending for Code-39


Truncate Ending for Industrial 2 of 5


Truncate Ending for MSI / Plessey

Truncate Ending for UPC-E

Truncate Ending for EAN-8

Truncate Ending for Codabar / NW7

Truncate Ending for Interleaved 2 of 5

Truncate Ending for Matrix 2 of 5

90 89

Enter

End End


Truncate Ending for UK / Plessey

Truncate Ending for Telepen

Truncate Ending for RSS(GS1 DataBar) Limited

Truncate Ending for RSS(GS1 DataBar) Expansion

Truncate Ending for RSS(GS1 DataBar) 14

Truncate Ending for RSS(GS1 DataBar) 14 Stack

Truncate Ending for RSS(GS1 DataBar) Expansion Stack

Enter Insert 0 Position

When adding data to the barcode data, insert position and insert data

function must be configured. If the insert position is configured as 0, the

character will insert in the front of the barcode data.

Procedure


(B) Scan “Insert 0 Position” barcode




Insert 0 Position for UPC-A

Insert 0 Position for EAN-13

Insert 0 Position for Code-39


Insert 0 Position for Industrial 2 of 5

91 92

Enter Enter

End End


Insert 0 Position for UPC-E


Insert 0 Position for Codabar / NW7

Insert 0 Position for Interleaved 2 of 5

Insert 0 Position for Matrix 2 of 5


Insert 0 Position for MSI / Plessey

Insert 0 Position for Telepen

Insert 0 Position for RSS(GS1 DataBar) Limited

Insert 0 Position for RSS(GS1 DataBar) Expansion

Insert 0 Position for UK / Plessey

Insert 0 Position for RSS(GS1 DataBar) 14

Insert 0 Position for RSS(GS1 DataBar) Expansion Stack

94 93

Enter

End End

Enter Insert 1 Position

When adding data to the barcode data, insert position and insert data

function must be configured.

If insert position is configured as 1, the character will be inserted behind

the first barcode digit. The insert position value can be configured

according to user preferences.

Procedure


(B) Scan “Insert 1 Position” barcode



Insert 1 Position for UPC-A




Insert 1 Position for Industrial 2 of 5


Insert 1 Position for UPC-E


Insert 1 Position for Codabar / NW7

Insert 1 Position for Interleaved 2 of 5

Insert 1 Position for Matrix 2 of 5


95 96

Enter Enter

End End

Insert 1 Position for MSI / Plessey

Insert 1 Position for Telepen

Insert 1 Position for RSS(GS1 DataBar) Limited

Insert 1 Position for RSS(GS1 DataBar) Expansion

Insert 1 Position for UK / Plessey

Insert 1 Position for RSS(GS1 DataBar) 14

Insert 1 Position for RSS(GS1 DataBar) 14 Stack

Insert 0 Position for RSS(GS1 DataBar) Expansion Stack

Insert 0 Data

This function can append one or two characters into the barcode data.

But please make sure the value of insert position can not be greater than

the length of barcode Otherwise, setting will be no effect.

Procedure


(B) Scan “Insert 0 data” barcode




Insert 0 Data for UPC-A

Insert 0 Data for EAN-13

Insert 0 Data for Code-39


Insert 0 Data for Industrial 2 of 5

98 97

Enter Enter

End End


Insert 0 Data for MSI / Plessey

Insert 0 Data for UPC-E


Insert 0 Data for Codabar / NW7

Insert 0 Data for Interleaved 2 of 5

Insert 0 Data for Matrix 2 of 5


Insert 0 Data for UK / Plessey

Insert 0 Data for Telepen

Insert 0 Data for RSS(GS1 DataBar) Limited

Insert 0 Data for RSS(GS1 DataBar) Expansion

Insert 0 Data for RSS(GS1 DataBar) 14

Insert 0 Data for RSS(GS1 DataBar) 14 Stack

Insert 0 Data for RSS(GS1 DataBar) Expansion Stack

99 100

Enter

End End

Enter Insert 1 Data

This function can append one or two characters into the barcode data.

But please make sure the value of insert position can not be greater than

the length of barcode Otherwise, setting will be no effect.

Procedure


(B) Scan “Insert 1 data” barcode




Insert 1 Data for UPC-A




Insert 1 Data for Industrial 2 of 5


Insert 1 Data for MSI / Plessey

Insert 1 Data for UPC-E


Insert 1 Data for Codabar / NW7

Insert 1 Data for Interleaved 2 of 5

Insert 1 Data for Matrix 2 of 5


102 101

End End

Enter Enter

Insert 1 Data for UK / Plessey

Insert 1 Data for Telepen

Insert 1 Data for RSS(GS1 DataBar) Limited

Insert 1 Data for RSS(GS1 DataBar) Expansion

Insert 1 Data for RSS(GS1 DataBar) 14

Insert 1 Data for RSS(GS1 DataBar) 14 Stack

Insert 1 Data for RSS(GS1 DataBar) Expansion Stack

Appendix：Hexadecimal / Decimal Table

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

OK

103 104

Appendix：ASCII Code Table Appendix：ASCII Code Table

106 105

Documents

DS800 BT UserManual 20120814 - dubacotech.comdubacotech.com/dimage/downs/DS800(BT)_UserManual_20120814.… · Title: Microsoft Word - DS800_BT__UserManual_20120814.doc Author: Administrator