DRILL PRESS■ STOCK No.63221 ■ PART No.HD19/16C

63275 HD19/16CF

• INSTRUCTIONS •IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE

SAFE AND EFFECTIVE USE OF THIS TOOL.

GENERAL INFORMATIONThis manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, whichshould be kept with the machine.This manual describes the purpose for which this tool has been designed and contains all the necessaryinformation to ensure its correct and safe use.We recommend that this manual is read before any operation ofthe machine, before performing any kind of adjustment to the machine, and prior to any maintenance tasks. Byfollowing all the general safety instructions contained in this manual, it will ensure both machine and operatorsafety, together with longer life of the tool itself.All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of themachine.Whilst every effort has been made to ensure accuracy of information contained in this manual, the Draper Toolpolicy of continuous improvement determines the right to make modifications without prior warning.

12/2000

DRILL PRESS■ STOCK No.63221 ■ PART No. HD19/16C

63275 HD19/16CF

CONTENTS:Page No.

Declaration of Conformity..............................................................................................1

Specification/Guarantee ................................................................................................2

Power Supply .................................................................................................................3

General Safety Instructions ............................................................................................4

Additional Safety Rules ..................................................................................................5

Unpacking and Checking ..............................................................................................6

Getting to Know Your Drill Press ....................................................................................7

Assembly ..................................................................................................................8-11

Operation and Use ..................................................................................................11-15

Trouble Shooting..........................................................................................................15

Optional Accessories ...................................................................................................16

WeDraper Tools Ltd. Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF.England.Declare under our sole responsibility that the product:Stock Nos:- 63221 & 63275.Part Nos:- HD19/16C & HD19/16CF.Description:- Pillar Drill.To which this declaration relates is in conformity with the following directive(s)98/37/EC, 73/23/EEC & 89/336/EEC.With reference to: EN 60204-1 & prEN 12717.

JOHN DRAPERManaging Director 14/11/2000

DECLARATION OF CONFORMITY

- 1 -

SPECIFICATION

- 2 -

The Draper Tools policy of continuous improvement determines the right to changespecification without notice.

HD19/16CF63275

19mm (3⁄4")16mm (5⁄8")

MT316 (190 - 2900)

430mm85mm72mm

350mmØ490 x 290mm

560W - 230V/50Hz1625mm80/85kg

HD19/16C63221

19mm (3⁄4")16mm (5⁄8")

MT316 (190 - 2900)

430mm85mm80mm

350mmØ480 x 270mm

560W - 230V/50Hz1070mm70/75kg

Part NoStock NoDrilling CapacityChuck CapacitySpindle TaperSpeeds (RPM)SwingSpindle TravelColumn DiameterTable SizeBase SizeMotor SizeHeightNett WeightSound pressure level 70dB (A) 70dB (A)

Draper machine tools have been carefully tested and inspected before shipment andare guaranteed to be free from defective materials and workmanship for a period of 12months from the date of purchase except where tools are hired out when the guaranteeperiod is ninety days from the date of purchase.

Should the machine develop any fault, please return the complete tool to your nearestauthorized warranty repair agent or contact Draper Tools Limited, Chandler's Ford,Eastleigh, Hampshire, SO53 1YF. England. Telephone: (023) 8026 6355.

If upon inspection it is found that the fault occurring is due to defective materials orworkmanship, repairs will be carried out free of charge. This guarantee does not applyto normal wear and tear, nor does it cover any damage caused by misuse, careless orunsafe handling, alterations, accident, or repairs attempted or made by any personnelother than the authorised Draper warranty repair agent.

This guarantee applies in lieu of any other guarantee expressed or implied andvariations of its terms are not authorised.

Your Draper guarantee is not effective unless you can produce upon request a datedreceipt or invoice to verify your proof of purchase within the 12 month period.

Please note that this guarantee is an additional benefit and does not affect yourstatutory rights.

Draper Tools Limited

GUARANTEE

ALWAYS WEAR EAR PROTECTION

- 3 -

CONNECTING YOUR MACHINE TO THE POWER SUPPLY: (230V)To eliminate the possibility of an electric shock your machine has been fitted with a BSapproved, non rewireable moulded plug and cable which incorporates a fuse, the valueof which is indicated on the pin face of the plug. Should the fuse need to be replaced an

approved BS1362 fuse must be used of the same rating, marked thus .The fuse cover is detachable, never use the plug with the cover omitted. If a replacementfuse cover is required, ensure it is of the same colour as that visible on the pin face of theplug (i.e. red). Fuse covers are available from your Draper Tools stockist.If the fitted plug is not suitable, it should be cut off and destroyed. *The end of the cableshould now be suitably prepared and the correct type of plug fitted. See below.

*WARNING:A plug with bare flexible wires exposed is hazardous if engaged in a live power socketoutlet.

WARNING YHIS APPLIANCE MUST BE EARTHED.The mains lead is coloured Green and Yellow-Earth, Blue-Neutral & Brown-Live. As thesecolours may not correspond with the coloured markings identifying the terminals inyour plug, proceed as follows. The wire which is coloured green and yellow must beconnected to th terminal in your plug marked with the letter ‘E’ or by the earthsymbol or coloured green or green and yellow. The wire which is coloured bluemust be connected to the terminal which is marked with the letter ‘N’ or black or blue.The wire which is coloured brown must be connected to the terminal which is markedwith the letter ‘L’ or coloured red or brown.

POWER SUPPLY

7.5m15m22.530M45M

0.750.750.750.750.75

0.750.750.750.751.25

1.01.01.0

1.251.5

1.251.51.51.52.5

Wire Size mm2Extension cable length

Ampere rating(on Name plate)

3 6 10 13

EXTENSION LEAD CHART:Extension lead sizes shown assure a voltage drop of not more than 5% at rated load of tool.

- 4 -

GENERAL SAFETY INSTRUCTIONSFOR POWER TOOLS

1. KNOW YOUR POWER TOOLRead and understand the owner's manual and labelsaffixed to the tool. Learn its application and limitations aswell as the specific potential hazards peculiar to this tool.

2. KEEP WORK AREA CLEANCluttered areas and benches invite accidents. Floors mustnot be slippery due to oil or sawdust.

3. AVOID DANGEROUS ENVIRONMENTSDo not use power tools in damp or wet locations, orexpose them to rain. Keep work area well lit. Provideadequate space surrounding the work area. Do not use inenvironments with a potentially explosive atmosphere.

4. KEEP CHILDREN AWAYAll visitors should be kept a safe distance from work area.

5. STORED TOOLSWhen not being used, all tools should be stored in a dry,locked cupboard or out of the reach of children.

6. WEAR PROPER CLOTHINGDo not wear loose clothing, neckties or jewellery (rings,wristwatches) to catch in moving parts. NONSLIP footwearis recommended.Wear protective hair covering to containlong hair. Roll long sleeves above the elbow.

7. USE SAFETY GOGGLES (Head Protection)Wear CE approved safety goggles at all times. Normalspectacles only have impact resistant lenses, they areNOT safety glasses. Also, use face or dust mask ifapplication is dusty and ear protectors (plugs or muffs)during extended periods of operation.

8. NOISE LEVELSSome types of machines may have high noise levels whenworking. In such cases ear protection must be worn.

9. VIBRATION LEVELSHand held power tools produce different vibration levels.You should always refer to the specifications and relevantHealth and Safety guide.

10. DUST EXTRACTIONIf your tool is fitted with a dust extraction fitting, alwaysensure that it is connected and being used with a dustextractor.Vacuum cleaners can be used if suitable for thematerial being extracted.

11. PROTECT YOURSELF FROM ELECTRIC SHOCKWhen working with power tools, avoid contact with anyearthed items (e.g. pipes, radiators, hobs andrefrigerators, etc.). If you are using a power tool inextreme conditions (e.g. high humidity or generatingmetal dust), always use an RCD (residual current device)at the power socket.

12. STAY ALERTAlways watch what you are doing and use common sense.Do not operate a power tool when you are tired or underthe influence of alcohol or drugs.

13. WHEN WORKING OUT OF DOORSOnly use extension leads designed for that purpose.

14. ACCESS TO MAINS SOCKETIf a stationary machine is fitted with a moulded plug andcable, the machine should not be positioned so thataccess to the mains socket is restricted.

15. DISCONNECT POWER TO THE TOOLWhen not in use, before servicing and when changingaccessories such as cutters, etc.

16. AVOID ACCIDENTAL STARTINGMake sure the switch is in the OFF position beforeplugging the machine into the power supply.

17. NEVER LEAVE MACHINE RUNNING UNATTENDEDTurn power off. Do not leave machine until it comes to acomplete stop.

18. DO NOT ABUSE THE CORDNever carry the tool by the power cable or pull it fromthe socket. Keep the power cable away from heat, oil andsharp edges.

19. NEVER STAND ON TOOLSerious injury could occur if the tool is tipped or if thecutting tool is accidentally contacted. Do not storematerials above or near the tool, so that it is necessary tostand on the tool to reach them.

20. CHECK DAMAGED PARTSCheck for damage to parts, breakage of parts, mountingsand any other conditions that may affect its operation.A guard or other part that is damaged should be properlyrepaired or replaced.

21. KEEP GUARDS IN PLACEAnd in working order.

22. MAINTAIN TOOLS WITH CAREKeep tools sharp and clean for the best and safestperformance. Follow instructions for lubricating andchanging accessories. All extension cables must bechecked at regular intervals and replaced if damaged.Always keep the hand grips on the tool clean, dry andfree of oil and grease.

23. USE RECOMMENDED ACCESSORIESConsult the owners manual for recommendedaccessories. Follow the instructions that accompany theaccessories. The use of improper accessories may causehazards.

24. REMOVE ADJUSTING KEYS AND WRENCHESForm a habit of checking to see that keys and adjustingwrenches are removed from the tool before turning it on.

25. SECURE WORKUse clamps or a vice to hold work. This frees both handsto operate the tool.

26. DO NOT OVERREACHKeep proper footing and balance at all times.

27. USE RIGHT TOOLDo not force the tool or attachment to do a job for which itwas not designed.

28. DO NOT FORCE TOOLIt will do the job better and safer at the rate for which it was designed.

29. DIRECTION OF FEEDFeed work into a blade or cutter against the direction ofrotation of the blade or cutter only.

30. WHEN DRILLING OR SCREWING INTO WALLSAlways make sure there is no danger of hitting any hiddenpower cables, water or gas pipes in the wall.

WARNINGPlease read the following instructions carefully, failure to do so could lead to serious personal injury.

IMPORTANTDraper Tools Limited recommends that this machine should not be modified or used for any application otherthan that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us inwriting and we will advise you.

IMPORTANT NOTEResidual Risk. Although the safety instructions and operating manuals for our tools contain extensiveinstructions on safe working with power tools, every power tool involves a certain residual risk which can not becompletely excluded by safety mechanisms. Power tools must therefore always be operated with caution !

1. This drill press is intended for useonly with drill bits. The use of anyother accessories may be hazardous.

2. CHECK to see that the drill bit issecurely locked in the chuck.

3. CORRECT DRILLING SPEEDSImportant factors which determine thebest speed to use in any drill pressoperation are:(a) The smaller the drill the greater

the required r.p.m. (revolutionsper minute)

(b) In soft materials the speed shouldbe higher than for hard materials.

4. MAKE sure that the chuck key isremoved before turning on power.

5. CHECK to see that the chuck issecurely fastened to the spindle.

6. CAUTIONWhen practical, use a vice or clampsto secure workpiece to avoidworkpiece rotating with the drill bit.

7. SECURE the tool to a workbench orfloor. If during operation there is anytendency for the drill press to tip over,slide or walk on the supportingsurface, the drill base must be securedto the supporting surface withfasteners through the holes located inthe drill press base.

8. For your safety DO NOT wear gloveswhen operating a drill press.

- 5 -

ADDITIONAL SAFETY RULES FORDRILL PRESSES

- 6 -

UNPACKING AND CHECKING CONTENTS

Carefully unpack the bench drill and all loose items from the carton. Illustrated belowis the bench drill and all loose items. NOTE: Some loose parts may be packed inside thepulley cover.

Now referring to Fig.1. carefully check that all the parts are present.

Please contact the stockist where your purchase was made if you have any enquiries, egproblems with assembly, apparent missing/damaged parts, help with accessoriesavailable or technical advice or alternatively call the Draper Helpline on (023) 8049 4344.

Fig.1.

- 7 -

GETTING TO KNOW YOURDRILL PRESS

✕✌ MOTOR ✕✕✌ TABLE LOCKING HANDLE✖✌ PULLEY COVER ✕✖✌ COLUMN✗✌ MOTOR PULLEY ✕✗✌ BASE✘✌ INTERMEDIATE PULLEY ✕✘✌ RACK✙✌ SPINDLE PULLEY ✕✙✌ TABLE RISE AND FALL HANDLE✚✌ SPECIFICATION LABEL ✕✚✌ RACK SECURING RING✛✌ DOWN FEED ASSEMBLY ✕✛✌ NO-VOLT TYPE ON/OFF SWITCH✜✌ CHUCK GUARD ✕✜✌ DRIVE BELT - TENSION ADJUSTER✢✌ CHUCK ✕✢✌ RISE AND FALL LOCKING HANDLE✕✔✌ TABLE

✕✖✌

✢✌

✕✕✌

✕✢✌

✜✌

✖✌

✕✘✌

✕✙✌

✕✗✌

✕✚✌

✗✌

✕✛✌

✛✌

✚✌

✕✌

✕✔✌

✕✜✌

✘✌✙✌

ASSEMBLY

ASSEMBLING THE DRILL PRESS1. Secure column ✪✌ to base ✫✌ using thefour bolts ✬✌. Loosen grub screw and removecollar ✭✌ along with the rack ✮✌.

2. Locate worm gear ✯✌ into hole ✰✌ asshown in Fig.3.

3. Place rack ✱✌ in position in table bracket,as shown in Fig.4. and slide onto column ✲✌.

- 8 -

Fig.2.

Fig.3.

Fig.4.

✭✌

✪✌

✫✌ ✬✌

✯✌✰✌

✱✌

✲✌

✮✌

- 9 -

ASSEMBLY

4. Ease table bracket and rack all the way downonto the column. Replace collar ✳✌ and re-tighten the grub screw, locking rack ✴✌ intoplace.

5. Slide table ✵✌ into the table bracket asshown in Fig.6 and lock into place using thetable locking handle ✶✌.

6. Fix table raising handle ✷✌ and bracketlocking handle ✸✌ as shown in Fig 6.

7.Place the drill press head ✹✌ onto column asfar as it will go (seek assistance as it is heavy).Align the head and table to drill press base andtighten the two head locking screws ✺✌ asshown in Fig 7.

Fig.5.

Fig.6.

Fig.7.

✳✌

✴✌

✹✌

✺✌

✵✌

✶✌✷✌

✸✌

ASSEMBLY

8. Screw the three downfeed handles ✻✌ intothe three holes located in the pinion shaft asshown in Fig 8.

9. Making sure that the chuck ✼✌ is opened toits capacity, place it down on a bench. Cleanany excess grease off the large end of thespindle ✽✌. Insert the taper into the back ofthe chuck and with a scrap piece of timberand a hammer firmly tap them together.

10. Loosen the nut and bolt ✾✌ Fig.10 andslide the chuck guard ✿✌ up onto the collar❀✌. Tighten the nut and bolt and lift the guard

into the upright position.

11. Now clean the other end of the arbor ❁✌Fig.11 from grease and offer it up to thespindle ❂✌. Rotate the arbor and chuck untilthe flats on the arbor engage into the spindle❂✌. Then firmly tap once using a hammer and

scrap piece of timber. Should it be required,removal of the arbor from the spindle isachieved by lowering the spindle, and with thedepth gauge, lock it in the down position. Onthe side of the spindle is a hole which exposesthe top of the arbor (if this cannot be seenfully, rotate the chuck slightly). Now using thetool provided, tap into the hole forcing thearbor down and out.

- 10 -

Fig.8.

Fig.9.

Fig.10.

Fig.11.

✻✌

✽✌

✼✌

✾✌

✿✌

❀✌

❁✌

❂✌

OPERATION AND USE

NO-VOLT ON/OFF SWITCH: (Fig 12)The drill is fitted with a no-volt switch with anemergency shut-off cover ❃✌.

In the event of an emergency, closing the coverfirmly will cause the stop button to betriggered, thus stopping the machine. To re-open the cover, the red button requires slidingup which in turn will release the stop button.

In the event of a power failure the drill presswill have to be manually re-started.

To switch the drill press on, lift up the sprungcover and push the button marked ✲✌.

To switch the drill press off, lift up the sprungcover and push the button marked ✸✌.

To switch the drill press off in an emergencystrike the cover firmly which will trigger the✸✌button.

- 11 -

Fig.12.

❃✌

- 12 -

OPERATION AND USE

SPINDLE SPEEDSSixteen spindle speeds of: 190, 275, 300, 380,450, 465, 535, 630, 685, 690, 1210, 1320, 1400,1830, 1945 and 2680rpm are available withyour drill. The highest speed is obtained whenthe belt is on the largest step of the motorpulley and the smallest step of the spindlepulley as shown in Fig. 13.

CHANGING SPEEDS AND ADJUSTINGBELT TENSION1. Disconnect the drill press from the powersupply.2. Lift up the belt and pulley guard ✪✌ Fig. 14.

3. Release the belt tension by looseninglocking knob ✫✌ Fig. 15 and moving tensionlever ✬✌.4.With the belts slack, position the two belts✭✌ on the desired steps of the motor, centre

and spindle pulleys for the correct speed asshown in Fig. 15.

5. After the belt is positioned on the desiredsteps of the pulleys, move the tension leveruntil motor is under tension and the belt isproperly tensioned. Tighten tension lock knob✮✌ Fig. 16. The belt should be just tight

enough to prevent slipping. Excessive tensionwill reduce the life of the belts, pulleys andbearings. Correct tension is obtained whenthe belts ✯✌ can be flexed about 25mm out ofline midway between the pulleys using lightfinger pressure.

Fig.13.

Fig.14.

Fig.15.

Fig.16.

✭✌

✪✌

✬✌

✫✌

✯✌

✮✌

Spindle Motor

OPERATION AND USE

1. The table ✰✌ Fig. 17 can be raised orlowered on the drill press column byloosening the table clamp handle ✱✌ andturning the table raising and lowering handle✲✌. After the table is at the desired height,

tighten handle ✱✌.

2. The table can be rotated 360º on the tablebracket by loosening lock handle ✳✌ Fig. 18.

3. The table can be tilted right or left byunscrewing and removing the table alignmentgrub screw Fig. 18.

4. Fig. 18 illustrates the table alignment grubscrew removed. Loosen table locking bolt✴✌(Fig.19), tilt table to desired angle.

Retighten bolt ✴✌.When returning table tothe level position replace table alignmentgrub screw. This will automatically positionthe table surface at 90º to the spindle.

5. A tilt scale ✵✌ Fig. 20 is provided on thetable bracket casting to indicate the degreeof tilt. A cursor line ✶✌ is also provided onthe table to line up with the scale.

- 13 -

Fig.17.

Fig.18.

Fig.19.

Fig.20.

✰✌ ✱✌

✲✌

✴✌

✳✌

✶✌

✵✌

OPERATION AND USE

ADJUSTING SPINDLE RETURN SPRINGFor the purpose of automatically returning thespindle upward after the hole has beendrilled, a spindle return spring is provided inthe spring housing ✷✌ Fig. 21. This springhas been properly adjusted at the factory andshould not be disturbed unless absolutelynecessary. To adjust the return spring,proceed as follows:

1. Disconnect the drill press from the powersupply.2. Loosen the nut ✸✌ slightly. Do not removenut ✸✌ from shaft ✹✌.

3.While firmly holding spring housing ✺✌Fig. 22 pull out housing and rotate it until theboss ✻✌ is engaged with the next notch onthe housing. Turn the housing anticlockwiseto increase and clockwise to decrease springtension. Then tighten the nut to hold thehousing in place.

IMPORTANT:Nut ✼✌ Fig. 22 should not contact springhousing when tight.

DRILLING HOLES TO DEPTHWhere holes are to be drilled to exactly thesame depth, a depth stop is provided in thepinion shaft housing and is used as follows:1. Loosen lock handle ✾✌ Fig. 23 and rotatehousing ✽✌ until the pointer ✿✌ lines up withthe depth you wish to drill on the scale ❀✌.Then tighten lock handle ✾✌.2. All holes will then be drilled to the exactdepth, as indicated on the scale.

- 14 -

Fig.21.

Fig.23.

Fig.22.

✷✌

✹✌✸✌

✺✌

✻✌

✼✌

✾✌

✽✌

✿✌❀✌

The following directions will give the inexperienced operator a start on common drill pressoperations. Use scrap material for practice to get the feel of the machine before attemptingregular work.CORRECT DRILLING SPEEDSFactors which determine the best speed to use in any drill press operations are:Type of material being worked,Size of hole,Type of drill or other cutter,Quality of cut desired.The smaller the drill, the greater the required r.p.m. In soft materials the speed should behigher than for hard materials.DRILLING METALUse clamps to hold the workpiece when drilling in metal. The workpiece should never beheld in the hand; the drill may snatch the workpiece at any time, especially when breakingthrough. If the workpiece is twisted out of the operator’s hand, they may be injured.The workpiece must be clamped firmly while drilling; any tilting, twisting or shifting resultsnot only in a rough hole, but also increases drill breakage. For flat work, lay the workpieceon a wooden base and clamp it firmly down against the table to prevent it from moving. Ifthe workpiece is of irregular shape and cannot be laid flat on the table, it should be securelyblocked and clamped using vee-blocks, clamps or a machine vice.

OPERATION AND USE

- 15 -

WARNING: FOR YOUR OWN SAFETY ALWAYS TURN THE MAIN SWITCH ON THE MACHINE “OFF” ANDREMOVE THE PLUG FROM THE POWER SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE ORTROUBLESHOOTING.

TROUBLE SHOOTING

TROUBLE

Noisy Operation

Bit burns or smokes

Excessive drill run-out or wobble

Drill binds in workpiece

PROBABLE CAUSE

1. Incorrect belt tension2. Dry spindle3. Loose spindle pulley or motor pulley

1. Incorrect speed2. Swarf not coming out of hole3. Blunt bit4. Feeding too slow5. Not lubricated6. Bit running backwards

1. Bent bit2.Worn spindle bearings3. Bit not properly installed in chuck4. Chuck not properly installed

1.Workpiece pinching bit or excessivefeed pressure2. Improper belt tension

REMEDY

1. Adjust tension2. Lubricate spindle with grease (ISO VG68)3. Tighten set screws in pulleys

1. Change speed2. Retract bit frequently to clear swarf3. Sharpen or replace bit4. Feed fast enough to allow drill to cut5. Lubricate bit6. Check motor rotation

1. Use a straight bit2. Replace3. Install bit centrally4. Refit chuck properly

1. Support or clamp workpiece2. Adjust tension

The following accessories are available from your local Draper power stockist.

WOOD MORTICING ATTACHMENT

25560 60mm

33686 55mm

36577 55mm

DRILL PRESS VICES

PART No.DPVManufactured from cast iron with fully hardened jaws. Carton packed.

STOCK JAW-MM JAW-MMNo. WIDTH OPENING

54634 75 8054635 100 9054636 120 11854637 145 140

OPTIONAL ACCESSORIES

- 16 -

NOTES

- 17 -

- 18-

NOTES

DRAPER TOOLS LIMITED,Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K.

Helpline: (023) 8049 4344.Sales Desk: (023) 8049 4333.

General Enquiries: (023) 8026 6355.Fax: (023) 8026 0784.

www.draper.co.uke-mail: sales@draper.co.uk

©Published by Draper Tools Ltd.No part of this publication may be reproduced,

stored in a retrieval system or transmitted inany form or by any means, electronic, mechanical

photocopying, recording or otherwise without priorpermission in writing from Draper Tools Ltd.

YOUR DRAPER STOCKIST