WIRING DIAGRAM IN CONDUIT (BY OTHERS)

To fixture

ON/OFF

Con

duit

prov

ided

by

othe

rs

DIM

0-10

V -

0-10

V +

To fixture

Neu

tral

Gro

und

Live

Power input fromprevious fixture

To next fixture

Con

duit

prov

ided

by

othe

rs

SPR5 OR SPR7To fixture

Neu

tral

Gro

und

Live

Con

duit

prov

ided

by

othe

rs

Neu

tral

Gro

und

Live

Power input fromprevious fixture

To next fixture

not required

AmericanColor Code

USE

White Neutral

Purple/Red 0-10V+

Black Live 120 - 480V

Gray/Orange 0-10V -

Green Ground

TENON INSTALLATION

REQUIRED TOOLS

AS DELIVERED

LUMINAIRE (1X)

TORQUE RATCHET

STEP 1. OPEN COVER STEP 2. LOOSEN BOLTS TO LOOSEN U-CLAMPS

STEP 5. MAKE CONNECTIONS WITH WIRE NUTS AND CLOSE COVER

DO NOT REMOVE BOLTS(bolts need to be tightened enough to

support luminaire)

NOTICE

KEEP WIRES CLEARWHEN CLOSING COVER

NOTICE

INSERT TENON ONTO U-CLAMPS

CLAMPS FOR TENON [Ø60mm]Ø2 "3

8

[60mm]4"@ 0°

0°

STEP 4. ADJUST LUMINAIRE USING INTERNAL SCALE AND TIGHTEN BOLTSSTEP 3. INSTALL LUMINAIRE ON TENON

ADJUST TENON ON SCALE (adjustable within -4.5º to 4.5º

in 1.5º increments)

SCALEUSE BUBBLE LEVEL TO INSTALL

LUMINAIRE PARALLEL TO THE GROUND. TIGHTEN BOLTS.

BUBBLE LEVEL

USE SLOTS TO OPEN COVER

4XHEX KEY SIZE 9/16

4XHEX KEY SIZE 9/16

MAGNETIC CLOSURE SYSTEM MAY CAUSE INJURY. KEEP FINGERS CLEAR.

WARNING!

Power input fromprevious fixture

To next fixture

RECOMMENDED TORQUE:250 lbs.in [28 N.m]

SOCKET SIZE: 9/16"

NOTICEWARNING!

DO NOT EXCEED FIXTURE SPECIFIED VOLTAGE.

CAUTIONUNAUTHORIZED FIELD REPAIRS

WILL VOID WARRANTY.

DO NOT USE IF FIXTURE, PARTS OR CONNECTORS ARE DAMAGED.

1/2” NPT, PG16 OR 20MM STRAIN RELIEF REQUIRED, PROVIDED BY OTHERS

WARNING!

DISCONNECT POWER BEFORE INSTALLING OR SERVICING TO AVOID ELECTRICAL SHOCK.

WARNING!

WARNING!

FIXTURE CORD SHOULD BE FED THROUGH THE TOP KNOCKOUT HOLE OF THE JBOX.

WARNING!

SEPARATION OF FIELD INSTALLED POWER LIMITED CIRCUIT (DIMMING/CONTROL)

WIRING FROM THE BRANCH CIRCUIT WIRING IN THE OUTLET BOX ARE TO BE MADE IN ACCORDANCE WITH LOCAL AND/OR

NATIONAL ELECTRICAL INSTALLATION CODES.

MEDIUM AREA LIAMWHITE

lumenicon

2019.02.12MS - R0

p.1/3

drawing number 207624

INSTALLATION INSTRUCTIONSThis product must be installed in accordance with applicable national and local electrical and constructioncodes by a person familiar with the construction and operation of the product and the hazards involved.

Failure to comply with the following installation instructions may result in death or serious injury. !

1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. AAAA

Confidential and proprietaryLumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.

PU8-W1X - WALL MOUNTED DECORATIVE ARM

STEP 2. INSTALL ARM ON WALL PLATE, MAKE CONNECTION AND INSTALL LUMINAIRE

STEP 2. INSTALL BRACKET ON POLE, MAKE CONNECTIONS AND INSTALL LUMINAIRE

STEP 3. WIRING DIAGRAM AT JUNCTION BOX (BY OTHERS)

STEP 1. INSTALL WALL PLATE WALL PLATE DIMENSIONS

RTV silicone

FOR WET LOCATION INSTALLATIONS, USE WEATHER-PROOF JUNCTION BOXES AND SEAL ALL POSSIBLE WATER ENTRY POINTS AND COVERS USING RTV

SILICONE. (SEALING COMPOUND AND JUNCTION BOXES BY OTHERS)

WARNING!

JUNCTION BOX(PROVIDED BY OTHERS)

SPR5 OR SPR7

Power input or from

previous fixture

To fixture

To next fixture

Junction box (by others)

LineGroundNeutralWire-nuts

To fixture

Power input or from

previous fixture

To next fixture

Junction box (by others)

From third party dimmer

LineGroundNeutralWire-nuts

0-10V -0-10V +

0-10V DIMMINGTo fixture

Power input or from

previous fixture

To next fixture

Junction box (by others)

LineGroundNeutralWire-nuts

Not requiredNot required

ON/OFF

PLEASE CONSIDER STREET SIDE WHEN

DRILLING

NOTICE

PU8-S1X - VARIABLE HEIGHT MOUNTING ON SQUARE POLE DECORATIVE ARM

STEP 1. LOCATE HOLES ON POLE OR REFER TO DRILLING PATTERNS TO CREATE THEM

90˚270˚

0˚

180˚

STREET SIDE

2X5/16-18HEX KEY SIZE 5/32

MOUNTING HARDWARE (4X)

(PROVIDED BY OTHERS, USE APPROPRIATE

SCREWS)

NOTICE

WIRE MUST BE AT LEAST 12"

[300mm]

MAKE SURE TO FEED THE WIRES THROUGH THE CENTER HOLE.

NOTICE

4XWALL PLATE

HOLE FOR WIRES

HOLE (4X)

2[64mm]

"12

[Ø11mm]

[76mm]

[152mm]

716

1[35mm]

"38

1"[Ø25mm]

Ø

Ø

3"

6"

AmericanColor Code

USE

White Neutral

Purple/Red 0-10V+

Black Line 120 - 480V

Gray/Orange 0-10V -

Green Ground

SUPPORT PLATE

2X3/8-16HEX KEY SIZE 9/16

1 2 3

INSTALL LUMINAIRE ON DECORATIVE ARMACCORDING TO

TENON INSTALLATIONSTEPS ON FIRST PAGE.

PLACE ARM ON WALL PLATE USING

THE HOOK

2

INSTALL LUMINAIRE ON DECORATIVE ARMACCORDING TO TENON INSTALLATION

STEPS ON FIRST PAGE.

1

INSTALL DECORATIVE ARM ON POLE USING

PROVIDED HARDWARE

SECURE FIXTURE USINGTHE SCREW AT THE BOTTOM

OF THE ARM.(INCLUDED WITH THE WALL BRACKET

HOLE (2X)FOR 3/8-16 BOLTS

[57mm]

[216mm]

1[43mm]

"34

8 "12

2 "14

[Ø73mm]2 "7

8

HOLE FOR WIRES

Ø

MEDIUM AREA LIAMWHITE

lumenicondrawing number 207624

INSTALLATION INSTRUCTIONSThis product must be installed in accordance with applicable national and local electrical and constructioncodes by a person familiar with the construction and operation of the product and the hazards involved.

Failure to comply with the following installation instructions may result in death or serious injury. !

2019.02.12MS - R0

p.2/3 1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. AAAA

Confidential and proprietaryLumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.

POLE-TOP MOUNTING DECORATIVE ARM

EXTERNAL TENON

INTERNAL TENON

PU2-SMLHorizontal small curve pole top

PU2-LRGHorizontal large curve pole top

PU4-S1E Single T shape pole top

PU4-S2E Double T shape pole top

PU5-S1E Single curve horizontal pole top

PU5-S2E Double curve horizontal pole top

PU8-S1ESingle tenon

PU8-S2EDouble tenon

PU8-S3ETriple tenon

PU8-S4EQuadruple tenon

Ø4"

INTERNAL ADAPTER

POLE EXTENSION

2X (3X@120°)Ø5/16 SET SCREWWITH FLAT LOCKWASHER AND NYLON INSERT LOCKNUT (INCLUDED WITH THE POLE)

8[203mm]

"

[Ø102mm]3

[76mm]"

7[178mm]

"

6XHEX KEY SIZE 5/16

[307mm]

PUSH ALL THE WIRES AND CONNECTORS

INTO THE POLE.

NOTICE

12 "116

[117mm]

4 "58

2X (3X@120°)Ø5/16 SET SCREWWITH FLAT LOCKWASHER AND NYLON INSERT LOCKNUT (INCLUDED WITH DECORATIVE ARM)

Ø4" [Ø102mm]

5XHEX KEY SIZE 5/16

STEP 1. INSTALL LUMINAIRE AND MAKE CONNECTIONS

2

INSTALL LUMINAIRE ON DECORATIVE ARMACCORDING TO TENON INSTALLATION

STEPS ON FIRST PAGE.

1

INSTALL DECORATIVE ARM ON POLE USING

PROVIDED HARDWARE

PU8 DECORATIVEARM SHOWN

MEDIUM AREA LIAMWHITE

lumenicondrawing number 207624

INSTALLATION INSTRUCTIONSThis product must be installed in accordance with applicable national and local electrical and constructioncodes by a person familiar with the construction and operation of the product and the hazards involved.

Failure to comply with the following installation instructions may result in death or serious injury. !

2019.02.12MS - R0

p.3/3 1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. AAAA

Confidential and proprietaryLumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.