Door Products VISION FRAMES - Anemostat · Door Products 4958 Stout Dr. #119, San Antonio, TX 78219 PH: 210.662.6300 • FAX: 210.662.2828 e-mail: [email protected] • website:

DETAIL DRAWING

INDExFOR

METALVISION

FRAMES

MODEL DESCRIPTION DATE PRINTED PAGESTANDARD

LoPro™. . . . . . . . . . . . . . . . . . . . . . Lo-Profile Self Attaching . . . . . . . . . . . . . . . . . . . . . . . . . . March 2012 . . . . . . . . . . . 1LoPro™-IS . . . . . . . . . . . . . . . . . . . Lo-Profile Special Glass or Door Thickness . . . . . . . . . . . July 2012 . . . . . . . . . . . . 2LoPro™-BB1-MB . . . . . . . . . . . . . . Lo-Profile Internal Mini-Blind . . . . . . . . . . . . . . . . . . . . . . . July 2014 . . . . . . . . . . . . 3LoPro™-STC . . . . . . . . . . . . . . . . . Lo-Profile Self Attaching / STC Rated . . . . . . . . . . . . . . . . May 2014. . . . . . . . . . . . 4WoodPro™ . . . . . . . . . . . . . . . . . . . Lo-Profile Self Attaching with Wood Veneer . . . . . . . . . . . May 2014. . . . . . . . . . . . 5StormPro-HR™ . . . . . . . . . . . . . . . Lo-Profile Self Attaching / Hurricane Rated . . . . . . . . . . . . May 2014. . . . . . . . . . . . 6StormPro-HR™-G . . . . . . . . . . . . . Lo-Profile Self Attaching / Hurricane Rated . . . . . . . . . . . . May 2014. . . . . . . . . . . . 7

SPECIALTYLoPro™-G. . . . . . . . . . . . . . . . . . . . Lo-Profile French Door Grilles . . . . . . . . . . . . . . . . . . . . . . May 2014. . . . . . . . . . . . 8FM-G . . . . . . . . . . . . . . . . . . . . . . . . Sidelite Mullions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014. . . . . . . . . . . . 9Grille / Mullion . . . . . . . . . . . . . . . . Design Confirmation Sheet . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 10FGS-75-G . . . . . . . . . . . . . . . . . . . . French Door Grilles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 11BFL-123-G . . . . . . . . . . . . . . . . . . . French Door Grilles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 12FGS-75 . . . . . . . . . . . . . . . . . . . . . . Thru – Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 13FGS-38 . . . . . . . . . . . . . . . . . . . . . . For 1 3/8” Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 14FGS-IS. . . . . . . . . . . . . . . . . . . . . . . Special Glass or Door Thickness. . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 15FGS-DBL. . . . . . . . . . . . . . . . . . . . . Double Glazing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 16BFL-123 . . . . . . . . . . . . . . . . . . . . . Self Attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 17BFL-75 . . . . . . . . . . . . . . . . . . . . . . Thru – Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 18BFL-75-PO . . . . . . . . . . . . . . . . . . . Post Office Observation . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 19X-RAY

LoPro. . . . . . . . . . . . . . . . . . . . . . Lo-Profile Lead Lined. . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 20FGS-MS5-FR . . . . . . . . . . . . . . . . Lead Lined and Fire Rated . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 21

CUSTOMLo-FP-12 / LoFP-12-IS . . . . . . . . . . 12” Round / Lo-Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2015 . . . . . . . . . . . 22Lo-FP-18 / LoFP-18-IS . . . . . . . . . . 18” Round / Lo-Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2015 . . . . . . . . . . . 23Lo-FP-24 . . . . . . . . . . . . . . . . . . . . . 24” Round / Lo-Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2015 . . . . . . . . . . . 24FP-12. . . . . . . . . . . . . . . . . . . . . . . . 12” Round . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 25FP-18. . . . . . . . . . . . . . . . . . . . . . . . 18” Round . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 26FP-24. . . . . . . . . . . . . . . . . . . . . . . . 24” Round . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 27LoPro™-CS . . . . . . . . . . . . . . . . . . Non-Curved Custom Shapes / Lo-Profile . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 28LoPro™-CS . . . . . . . . . . . . . . . . . . Curved Custom Shapes / Lo-Profile . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 29LoPro™-CS-HC . . . . . . . . . . . . . . . Half Circle Custom Shapes / Lo-Profile . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 30LoPro™-CS-QR . . . . . . . . . . . . . . . Quarter Radius Custom Shapes / Lo-Profile . . . . . . . . . . . May 2014 . . . . . . . . . . . 31FGS-75-CS . . . . . . . . . . . . . . . . . . . Non-Curved Custom Shapes . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 32Fasteners for Vision Frames . . . . Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 33HM-CLIP . . . . . . . . . . . . . . . . . . . . . Hollow Metal Door Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . May 2014 . . . . . . . . . . . 34

MAY 2015METAL VISION FRAMES INDEX PAGE A

TECHNICAL DATAFROM

D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219

PH: 210.662.6300 • FAX: 210.662.2828e-mail: [email protected] • website: www.anemostat.com

Job Name & Location Submitted by

For Most Current Info, Consult Factory or check our website, www.anemostat .com

UNDERWRITERS’LABORATORIES

EN-1634European Standard

B.S.-476.22British Standard

FIRERATINGS

MARCH 2012METAL VISION FRAMES PAGE 1

Anemostat manufacturing dimensions ±1/32 (1mm)Actual dimensions are nominal and may varybased on component manufacturers tolerances.

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized(Coil,

FINISH: Custom Baked Enamel Colors (as per sample chip supplied). Plated Finishes to match the lock, hinges and closer.

FASTENERS: Special Security Screw Fasteners, See Page 36, this section.SPECIALS: Fractional Sizes, Lead Lined for X-ray applications.

Hot Dipped, or Zinc Plated) Mill Finish Aluminum-(Not Fire Rated).

and provides a low profile, flush to the door look. Uses 1 3/4" (44mm) sheet metal screws that pass through the door cutout, and fastens to the opposite side of the vision frame, thus eliminating the need to drill the door for thru bolts and saving installation time and labor. It also leaves the corridor side of the frame free of fasteners for added security and a cleaner, more aesthetic appearance.

fire and/or safety rated with U.L. and/or W.H.I. classification markings. Nominal glazing space of 3/8" (10mm) allows for glazing tape to be used on both sides of the glass.

MATERIAL: 20 GA. (1mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Our most popular product is easy to install

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.GLAZING: Should be 1/4" (6mm) , 3/16" (5mm) or 5/16" (8mm)

AESTHETICS: Tight mitered corners, beveled glass stop and lowprofile, provide a clean tapered look.

NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.

your area, to determine appropriate standards.Consult with the local authority having jurisdiction in

IMPORTANT: Interpretation of building and fire codes may vary.

For mullions see (LoPro™-G, FGS-75-G or BFL-123-G.)HM CLIP: Replaces the need for reinforcing channel see page 37 this section.

For Special Glass or Door thickness (see FGS-IS or LoPro™-IS ).

max. width 36" (914mm) , max. height 54" (1372mm).90 MINUTE:* Approved listing at 1296 sq.in. (0.836 m2) visible lite

3 Hour:* Approved listing at 100 sq.in. (0.065 m2) visible litemax. width 12" (305mm), max. height 33" (838mm)

20 MINUTE:* Approved listing at 3204 sq.in. (2.067 m2) visible litemax. width 36" (914mm), max. height 89" (2261mm).

45/60 MINUTE:* Approved listing at 2772 sq.in. (1.788 m2) visible litemax. width 36" (914mm), max. height 77"(1956mm).

* Must be used with FIRELITE Plus or NT and Fire listed glazing tape or another manufacturer’s equivalent product. Glazing combination must be used in appropriately tested door assembly.

BS 476.22: Timber Doors - 30 min. and 1 hour.Steel Doors - 2 hours (4 hours actual).

ORDERSIZE

&DOOR

CUTOUT

OUTSIDE

SPACEGLAZING

(6mm)

11/16"

GLAZINGMATERIAL

VISIBLELITE

ORDE

R SIZE

MINU

S 2"

GLASS

ORDE

R SIZE

MINU

S 1"

FRAME

ORDE

R SIZE

PLUS

1" (2

5mm)

ORDE

R SIZE

ISVIS

IBLE L

ITEPL

US 2"

INSIDE

5/64" 5/64"

DOOR ONLY

1/2" (13mm)

1" (25mm)

(10mm)SIZE

O.D.

(51mm

)

(25mm

)

3/8"

1/4"

(51mm

)

(17mm)

(2mm) (2mm)1 3/4"

(44mm)

DETAIL DRAWING

TECHNICAL DATAFROM

STANDARD PRODUCT FEATURES OPTIONAL FEATURES

FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure



LoPro™LO-PROFILE

METAL VISION FRAME

BS 476.22British Standard

EN-1634European Std.

30/60 min. integrity and insulation - Indicative Testing

PLEASE NOTE: On visible litesizes larger than 1296 sq. in.(0.836 m2) on 20/45 min. and100 sq. in. (0.065 m2) on60/90/180 min., please consultwith your Door / FrameManufacturer’s procedures, fortheir maximum glass sizetested.

WARNOCK HERSEY

NEWSound

Ratings

See LoPro-

STC

Page 4




WARNOCK HERSEY



FIRERATINGS

OUTSIDE

ORDE

R SIZE

MINU

S 2"

INSIDE

1/2" (13mm)

1" (25mm)

OR SPECIFY

5/64"5/64"

O.D.

PLUS

2" (5

1mm)

VISIBL

E LITE

ORDE

R SIZE

IS

ORDE

R SIZE

PLUS

1" (2

5mm)

FRAME

ORDE

R SIZE

MINU

S 1" (2

5mm)

1 3/4"(44mm)

11/16"(17mm)

(51mm

)

(2mm) (2mm)

GLAZINGSPACE

1 1/16" (27mm)

GLAZINGTHICKNESS

7/8" to 1"(22mm to 25mm)

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE

Anemostat manufacturing dimensions ±1/32 (1mm) Actual dimensions are nominal and may vary based on component manufacturers tolerances.

3/8" to 7/16"(10mm to 11mm)

1/2"(13mm)

1/4"(6mm)

3/8"(10mm)

GLAZINGSPACE

GLAZINGTHICKNESS

1/2" to 9/16"(13mm to 14mm)

5/8"(16mm)

3/4" to 13/16"(19mm to 21mm)

7/8"(22mm)

5/8" to 11/16"(16mm to 17mm)

3/4"(19mm)

GLAZINGSPACE

GLAZINGTHICKNESS

7/8" to 1"(22mm to 25mm)

1 1/16(27mm)

1/4"(6mm)

3/8"(10mm)

1/4"(6mm)

3/8"(10mm)

1 3/4" DOOR(44mm)

1 3/4" DOOR(44mm)

1 3/4" DOOR(44mm)

1 3/8" DOOR(35mm)

A A C1 C C1 A B1B1

1 3/4" DOOR(44mm)

1 3/4" DOOR(44mm)

2" DOOR(50mm) (54mm)

2 1/8" DOOR

C B1 B B1 D D1 E E1

LoPro-AB1-NR LoPro-AC1 LoPro-CC1 LoPro-AB1

LoPro-CB1 LoPro-BB1 LoPro-DD1 LoPro-EE1

DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-IS StyleLO-PROFILE METAL VISION FRAME

FOR SPECIAL GLASS OR DOOR THICKNESS



JULY 2012METAL VISION FRAMES PAGE 2



■ MATERIAL: 20 GA. (1mm) Cold Rolled Steel.■ FINISH: Gray Primer, Beige or Bronze Baked Enamel.■ INSTALLATION: Uses 1 3/4" (44mm) sheet metal screws that pass through

the door cutout, and fastens to the opposite side of the vision frame, savinginstallation time and labor. It also leaves the corridor side free of fasteners foradded security and a cleaner, more aesthetic appearance.

■ DOOR THICKNESS: 1 3/4" (44mm) is standard. Door thickness can varybased on Glazing Material thickness used, please consult factory. 2" (50mm) or 2 1/8" (54mm) are available with 1/4" (6mm) glazing material.

■ AESTHETICS: Tight mitered corners, beveled glass stop and a low profile toprovide a clean, tapered look.

GLAZING: Glazing Space will vary based on Glazing Material and willdetermine thickness of Glazing Tape used. Glazing Materialshould be fire and safety rated for use as a door lite with U.L.and/or W.H.I. markings when used in a fire rated assembly.

■ IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.

■ NOTE: For Exterior use, High Humidity or Salt Air application, product mustbe Galvanized or Stainless Steel.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil, Hot Dipped, or Zinc Plated) Mill Finish Aluminum (Not Fire Rated).

■ FINISH: Custom Baked Enamel Colors(as per sample chip supplied). Plated finishes to match the lock, hinges and closer.

■ FASTENERS: Special Security Screw Fasteners. See page 36, this section.■ SPECIALS: Fractional sizes. For mullions see LoPro™-IS-G or FGS-IS-G■ HM-CLIPS: Replaces the need for reinforcing channels in the door cutout, see pg. 37


Timber Doors - 30 min. and 1 hour. Steel Doors - 2 hours (4 hours actual).

■ 20/45/60/90 MINUTE:* Approved listing at 1080 sq. in. (0.697 m2) visible lite.max. width 36" (914mm), max. height 36" (914mm).

*Must be used with 7/8" (23mm) or 1-1/16" (27mm) Pyrostop and fire listed glazing tape, and be used in an appropriately tested door assembly.

■ 20 MINUTE:** Approved listing at 3204 sq. in. (2.067 m2) visible lite.max. w 36" (914mm), max. h 89" (2261mm).

■ 45/60 MINUTE:** Approved listing at 2772 sq. in. (1.788 m2) visible lite.max. w 36" (914mm), max. h 77" (1956mm).


■ 3 HOUR:** Approved listing at 100 sq. in. (0.065 m2) visible lite. max. w 12" (305mm), max. h 33" (838mm).

**Must be used with FIRELITE IGU 1" (25mm) Cat II or FIRELITE Plus and Fire listedglazing tape or another manufacturer’s equivalent product. Glazing combination mustbe used in appropriately tested door assembly.■ ATTENTION: On visible lite sizes larger than 1296 sq. in. (0.836 m2) on

20/45 min. and 100 sq. in. (0.065 m2) on 60/90/180 min., please consult withyour Door / Frame Manufacturer’s procedures, for their maximum glass sizetested.




For Most Current Info, Consult Factory or check our website, www.anemostat .comJULY 2014

METAL VISION FRAMES PAGE 3

Meets ANSI Z97.1 and CPSC 16CFR1201 (Cat. I and II)

ASTM C 1036ASTM C 1048

ORDERSIZE

&DOOR

CUTOUT

Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tollerances.

flush to the door look. Uses 1 3/4" (44mm) sheet metal screws that pass through the door cutout, and fastens to the opposite side of the vision frame, saving installation time and labor. It also leaves the corridor side of the framefree of fasteners for added security and a cleaner,more aesthetic appearance.

MATERIAL: 20 GA. (1mm) Cold Rolled Steel Vision Frame.

FINISH: Vision Frame: Grey Primer, Beige or Bronze Enamel.INSTALLATION: This product is easy to install and provides a low profile,

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal doors.AESTHETICS: Tight mitered corners, beveled glass stop and low

profile, provide a clean tapered look.USES: Hospitals, Judicial and Police Facilities, Board Rooms,

Offices or anywhere flexible privacy is required.


MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil,


FASTENERS: Special Security Screw Fasteners available,

OUTSIDE

Hot Dipped, or Zinc Plated).

SPACEGLAZING

11/16"

GLAZINGMATERIAL

VISIBLELITE

ORDE

R SIZE

MINU

S 3"

GLASS / MINI BLINDUNIT SIZE

FRAME

ORDE

R SIZE

PLUS

1" (2

5mm)

ORDE

R SIZE

ISVIS

IBLE L

ITEPL

US 2"

(51m

m)

INSIDE

5/64" 5/64"

DOOR ONLY

1/2" (13mm)

1" (25mm)O.D.

ORDE

R SIZE

MINU

S 1" (2

5mm)

(51mm

)

(17mm)

(2mm) (2mm)1 3/4"

(44mm)

LoPro™-BB1-MB is not fire rated.

MINI-BLIND: Available in white only. Internal Mini-Blind with nylon cord,

1 1/8" (29mm)

1" (25mm)

1 MINI BLIND OPERATOR

RAISE / LOWER / TILT(SIDE)

adjustable painted aluminum blades, sealed in clear tempered glass, 1" overall thickness. Blind will raise, lower and tilt. Adds privacy and security.

SIZES AVAILABLE: (Door Cutout Size)

see page 36 this section.

Only Available in LoPro™-BB1 with 1" insulated glass/mini blind unit.( )

9"x37" 9"x65" 15"x65" 21"x37" (229 x 940mm) (229 x 1651mm) (381 x 1651mm) (533 x 940mm)

8"x65" 21"x65" 23"x37" 23"x49" 23"x65" (203 x 1651mm) (533 x 1651mm) (584 x 940mm) (584 x 1245mm) (584 x 1651mm) (tilt only) Custom sizes not available.

DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-BB1-MBLO-PROFILE

METAL VISION FRAMEWITH

INTERNAL MINI-BLINDGLASS UNIT


FIRE RATINGS



NOT FIRE RATED

MINI-BLIND UNITPATENT # 5,699,845

IMPACT / SAFETY RATINGS

CONFORMS TO THE FOLLOWING

CATEGORY II IMPACT/SAFETY RATED

OCTOBER 2014METAL VISION FRAMES PAGE 4






FIRE RATINGS WHERE APPLICABLE

Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Coil,


FASTENERS: Special Security Screw Fasteners, See Page 36, this section.SPECIALS: Fractional Sizes

See appropriate Glazing Product Tech Data page

or Zinc Plated).MATERIAL: 20 GA. (1mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.

INSTALLATION: Our most popular product is easy to install and provides a low profile, flush to the door look. Uses 1 3/4" (44mm) sheet metal screws that pass through the door cutout, and fastens to the opposite side of the vision frame. Vision frame comes with sound sealing tape applied to the underside perimeter of both frame sides.

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.GLAZING: Glass is supplied with GT Glazing Tape for both sidesAESTHETICS: Tight mitered corners, beveled glass stop and low

profile, provide a clean tapered look.




HM CLIP: Replaces the need for reinforcing channelin the door cutout, see page 37 this section.

LoPro-STC with 1/4" (6mm) SAFE-Wire:* STC - 38LoPro-STC with 3/16" (5mm) FireLite NT:* STC - 35LoPro-STC with 5/16" (8mm) FireLite Plus:* STC - 38LoPro-STC with 1" (25mm) FireLite Plus IGU:* STC - 42LoPro-STC with 7/8" (23mm) Pyrostop 60-101 23mm:* STC - 41LoPro-STC with 1" (25mm) Laminated IGU: STC - 42 (Safety Rated Only)LoPro-STC with 1" (25mm) Tempered IGU: STC - 35 (Safety Rated Only)TESTED SIZE: 24" X 36" (610 X 914mm) CUTOUT / ASSEMBLYTESTED IN ACCORDANCE WITH: ASTM E90-09 and ASTM E2235-04. STC measurements determined in accordance with ASTM E413-04.Testing conducted at Western Electro - Acoustic Laboratory, Santa Clarita, CA.* Fire Rated - see Glazing Section for ratings and maximum allowable sizes

ORDERSIZE

&DOOR

CUTOUT GLAZING SPACE

11/16"

GLAZINGMATERIAL

VARIES

VISIBLELITE

ORDE

R SIZE

MINU

S 2" (5

1mm)

GLASS

ORDE

R SIZE

MINU

S 1" (2

5mm)

FRAME

ORDE

R SIZE

PLUS

1" (2

5mm)

ORDE

R SIZE

ISVIS

IBLE L

ITEPL

US 2"

(51m

m)

OUTSIDE INSIDE

5/64" (2mm) 5/64" (2mm)DOOR ONLY

1/2" (13mm)

1" (25mm)

(10mm or 27mm)SIZE

O.D.

3/8" or 1-1/16"

(17mm)

1 3/4" (44mm)

A A1

DOOR

GLAZINGTAPE

GLAZINGTAPE

B B1

DOORSOUNDSEALINGTAPE

SOUNDSEALINGTAPE

Lo-Pro AA1

FIRE / SAFETY RATED1/4" (6mm) SAFE-Wire3/16" (5mm) FireLite NT5/16" (8mm) FireLite Plus

FIRE / SAFETY RATED1" (25mm) FireLite Plus IGU7/8" (23mm) Pyrostop 60-101SAFETY RATED ONLY1" (25mm) Laminated IGU1" (25mm) Tempered IGU

Lo-Pro BB1

GLAZINGTAPE

SOUNDSEALING TAPE

CAUTION: Sound Sealing Tape should not be exposed to a heat treating process from post factory applied finishes, such as powder coating.

DETAIL DRAWING

TECHNICAL DATAFROM


FIRE RATINGS (w/ U.L. classification markings) Positive Pressure

SOUND RATINGS

LoPro™-STCLO-PROFILE STC RATED

METAL VISION FRAME ASSEMBLY

SoundTransmissionClass

WARNOCK HERSEY

PLEASE NOTE: LoPro-STC must be purchased as a complete assembly (LoPro Vision Panel, Glass and Glazing Tape) in order to conform with STC Testing achieved.







ORDERSIZE

&DOOR

CUTOUT

OUTSIDE

SPACEGLAZING

(6mm)

11/16"

GLAZINGMATERIAL

VISIBLELITE

ORDE

R SIZE

MINU

S 2"

GLASS

ORDE

R SIZE

MINU

S 1" (2

5mm)

FRAME

ORDE

R SIZE

PLUS

1" (2

5mm)

ORDE

R SIZE

ISVIS

IBLE L

ITEPL

US 2"

(51m

m)

INSIDE

5/64" 5/64"

DOOR ONLY

1/2" (13mm)

1" (25mm)

(10mm)SIZE

O.D.

3/8"

1/4"

(51mm

)

(17mm)

(2mm) (2mm)1 3/4"

(44mm)

1-5/8(41mm)

5/32(4mm)

REAL WOOD VENEEROVER PVC PROFILE

DOUBLE SIDEDADHESIVE TAPE

NO VISIBLESCREWS

Dimensions for Wood Veneers Dimensions Shown for LoPro Metal Vision Frame

DETAIL DRAWING

TECHNICAL DATAFROM


FIRE RATINGS (w/ U.L. classification markings) Positive Pressure

WoodPro™LO-PROFILE

METAL VISION FRAMEWITH WOOD VENEER

PATENT PENDING

■ MATERIAL: Frame: 20 GA. (1mm) Cold Rolled Steel (LoPro Vision Frame).Wood Veneer: PVC and Wood Veneer

■ FINISH: Unfinished Red Oak, Maple, or Mahogany over Beige Enamel LoPro.■ INSTALLATION: WoodPro is easy to install and provides a low profile, flush

to the door real wood finish. Uses 1 3/4" (44mm) sheet metal screwsthat pass through the door cutout, and fastens to the opposite sideof the vision frame. The formed wood veneers are pre-mitered with self-adhesive tape for ease of installation. Wood putty or putty stickmay be required at miters to fill any small gaps.

■ DOOR THICKNESS: For 1 3/4" (44mm) Wood Doors.■ AESTHETICS: Tight mitered corners, beveled glass stop and a low profile to

provide a clean, tapered look. Veneers are unfinished realwood. No Visible Screws after installation.

GLAZING: Glazing Space will vary based on Glazing Material and willdetermine thickness of Glazing Tape used. Glazing Materialshould be fire and safety rated for use as a door lite with U.L.markings when used in a fire rated assembly.

■ IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.

■ SPECIALS: Veneers sold separately for use on existing LoPros. Consult Factory(Requires a compound miter cut by installer.)

■ 20 MINUTE: Approved listing at 2520* sq. in. (1.626 m2) visible lite. max. width 36" (914mm) , max. height 70" (1778mm).

■ 45/60 MINUTE: Approved listing at 2520* sq. in. (1.626 m2) visible lite. max. width 36" (914mm) , max. height 70" (1778mm).

■ 90 MINUTE: Approved listing at 1296* sq. in. (0.836 m2) visible lite. max. width 36" (914mm), max. height 54" (1372mm).

*Must be used with FIRELITE Plus or NT and Fire listed glazing tape or anothermanufacturer’s equivalent product. Glazing combination must be used in appropriatelytested door assembly.

IMPORTANT• For interior use only.• Minimum Width of

4" (102mm) Door CutoutMaximum Height of 72" (1829mm) Door Cutout


FIRE RATED BY

■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836 m2) on 20/45 min.and 100 sq. in. (0.065 m2) on 60/90 min., please consult with your Door / FrameManufacturer’s procedures, for their maximum glass size tested.

BSEN 1634-1

■ 30 MINUTE: Approved listing - Tested Size 16" (410mm) x 28" (711mm)BSEN-1634-1: 2008

MAY 2014METAL VISION FRAMES PAGE 6



OUTSIDE INSIDE

7/64" 7/64"(3mm) (3mm)

1 3/4"(44mm)

DOOR ONLY

SPACEGLAZING(16mm)

5/8"

(13mm)GLAZINGMATERIAL

1/2"

GLASS

ORDE

R SIZE

MINU

S 1"

SIZE

(25mm

)

ORDE

R SIZE

IS VI

SIBLE

LITE

PLUS

2 1/2

"(64

mm)

FRAME

ORDE

R SIZE

PLUS

1 1/2

" (38m

m)

O.D.

ORDE

R SIZE

MINU

S 2 1/

2"(64

mm)

15/16"(24mm) 1 1/4" (32mm)

3/4"(19mm)

LITEVISIBLE

(16mm)5/8"

HRT-090GLAZING

TAPE

HURRICANE GLASS1/2" (13mm) LAMINATED GLASS (INCLUDED)

ORDERSIZE&

DOORCUTOUT




DETAIL DRAWING

TECHNICAL DATAFROM


HURRICANE TEST / WINDSTORM APPROVALS (w/ U.L. marking)

StormPro-HR™LO-PROFILE HURRICANE RATEDMETAL VISION FRAME ASSEMBLY

■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and ANSI 250.13-Impact 350 FT LBS. (large missile test) Design Pressure: +/- 70 PSF.

■ Complies with Florida Building Code Standards

■ IMPORTANT: Interpretation of building and fire codes may vary. Consult with thelocal authority having jurisdiction in your area, to determineappropriate Standards.

■ ATTENTION: Must be used in an appropriately tested and hurricanerated door assembly.

■ MATERIAL: #304 Stainless Steel, #4 Finish(Satin), Hot Dipped, or Zinc Plated.■ FINISH: Special Order Baked Enamel Colors (as per sample chip supplied). Plated

Finishes to match the lock, hinges and closer.■ FASTENERS: Special Security Screw Fasteners, See Page 36, this section.■ SPECIALS: Fractional Sizes

FIRE RATINGS■ StormPro-HR™ is not fire rated

Florida Building CodeHurricane Approval

FILE #FL11736NOT FIRE RATED

HURRICANE RATED


FILE #R26087

■ MATERIAL: 18 GA. (1.25mm) Galvanized Steel, 1/2" (13mm) clear glass and VHB glazing tape.

■ FINISH: Grey Primer, Beige, or Bronze Baked Enamel.■ INSTALLATION: The StormPro™-HR is easy to install and provides a low

profile, flush to the door look. Uses 1-3/4" (44mm) sheetmetal screws that pass through the door cutout, and fastensto the opposite side of the vision frame. 5/8 (16mm) x .090 (2.3mm) thick conformable 3M VHBglazing tape is supplied and installed on both sides of theglass.

■ DOOR THICKNESS: For 1-3/4" (44mm) Hurricane Approved Metal doors■ GLAZING: Glass is comprised of 2 pieces of 3/16" (5mm) clear annealed with

a .120 Uvekol™ “S” clear laminate. Overall glass thickness is 1/2" (13mm).

■ AESTHETICS: Tight mitered corners, beveled glass stop and low profile,provide a clean tapered look.

■ MAxIMUM SIZE: 36" (914mm) wide x 72" (1829mm) tall cutout visible lite 33-1/2" x 69-1/2" (851 x 1765mm)

■ NOTE: For exterior use, high humidity or salt air application, product must begalvanized or stainless steel.

ASSEMBLY INCLUDES:VISION FRAME, GLAZING TAPE,

GLASS AND FASTENERS




OUTSIDE INSIDE

7/64" 7/64"(3mm) (3mm)

1 3/4"(44mm)

DOOR ONLY

SPACEGLAZING(16mm)

5/8"

(13mm)GLAZINGMATERIAL

1/2"

ORDE

R SIZE

MINU

S 1" (2

5mm)

GLASSSIZE

ORDE

R SIZE

IS V

ISIBL

E LITE

PLUS

2 1/2

" (64m

m)

FRAME

ORDE

R SIZE

PLUS

1 1/2

" (38m

m)

O.D.

ORDE

R SIZE

MINU

S 2 1/

2"(64

mm)

15/16"(24mm) 1 1/4"

(32mm)

3/4"(19mm)

LITEVISIBLE

(16mm)5/8"

HRT-090GLAZING

TAPE

HURRICANE GLASS, 1/2" (13mm)LAMINATED GLASS (INCLUDED)

5/8" x 1/4"(16mm x 6mm)SOLID STEEL

MULLIONS

ORDERSIZE&

DOORCUTOUT


STANDARD GRILLE DESIGNSCUSTOM DESIGNS AVAILABLE, SEE PAGE 10 THIS SECTION

G-9000G-6000G-4000

G-3000G-2000

G-5000 G-6000 G-8000

G-1000 G-1200 G-1500



DETAIL DRAWING

TECHNICAL DATAFROM


HURRICANE TEST / WINDSTORM APPROVALS (w/ U.L. marking)

StormPro-HR™-GLO-PROFILE HURRICANE RATEDMETAL VISION FRAME ASSEMBLYWITH FRENCH DOOR GRILLES

■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and ANSI 250.13-Impact 350 FT LBS. (large missile test) Design Pressure: +/- 70 PSF.

■ Complies with Florida Building Code Standards

■ IMPORTANT: Interpretation of building and fire codes may vary. Consult with thelocal authority having jurisdiction in your area, to determineappropriate Standards.

■ ATTENTION: Must be used in an appropriately tested and hurricanerated door assembly.

■ FINISH: Special Order Baked Enamel Colors (as per sample chip supplied). PlatedFinishes to match the lock, hinges and closer.

■ FASTENERS: Special Security Screw Fasteners, See Page 36, this section.■ SPECIALS: Fractional Sizes.

FIRE RATINGS■ StormPro-HR™ is not fire rated

Florida Building CodeHurricane Approval

FILE #FL11736NOT FIRE RATED

HURRICANE RATED


FILE #R26087

■ MATERIAL: 18 GA. (1.25mm) Galvanized Steel - Zinc Plated. 1/2" (13mm) Clear Glass and VHB Glazing Tape.

■ FINISH: Grey Primer, Beige, or Bronze Baked Enamel.■ INSTALLATION: The StormPro-HR™-G is easy to install and provides a low

profile, flush to the door look. Uses 1-3/4" (44mm) sheet metalscrews that pass through the door cutout, and fastens to theopposite side of the vision frame. 5/8 (16mm) x .090 (2.3mm)thick conformable 3M VHB glazing tape is supplied andinstalled on both sides of the glass.

■ DOOR THICKNESS: For 1-3/4" (44mm) Hurricane Approved Metal doors■ GLAZING: Glass is comprised of 2 pieces of 3/16" (5mm) clear annealed with

a .120 Uvekol™ “S” clear laminate. Overall glass thickness is 1/2" (13mm).

■ AESTHETICS: Tight mitered corners, beveled glass stop and low profile,provide a clean tapered look.

■ MULLIONS: Mullions are 5/8" x 1/4" (16 x 6mm) solid steel material fullywelded to the frame and to all intersecting points of the mulliondesign, and ground smooth.

■ MAxIMUM SIZE: 36" (914mm) wide x 72" (1829mm) tall cutout visible lite 33-1/2" x 69-1/2" (851 x 1765mm)

■ NOTE: For exterior use, high humidity or salt air application, product must begalvanized or stainless steel.

ASSEMBLY INCLUDES: VISION FRAME, GLAZING TAPE, GLASS AND FASTENERS




WARNOCK HERSEY



FIRERATINGS


SPECIALS: Choose from grille patterns as shown or create your own.Available for thicker glass.

FASTENERS: Special Security Screw Fasteners, see page 36.

FINISH: Custom Baked Enamel Colors (per sample chip supplied).

MATERIAL: Galvanized (Hot Dipped or Zinc Plated).

Plated finishes to match the lock, hinges and closer.

OUTSIDE

11/16"

ORDE

R SIZE

MINU

S 2"

ORDE

R SIZE

MINU

S 1" (2

5mm)

FRAME

ORDE

R SIZE

PLUS

1" (2

5mm)

ORDE

R SIZE

ISVIS

IBLE L

ITEPL

US 2"

(51m

m)INSIDE

5/64" 5/64"

DOOR ONLY

1/2" (13mm)

1" (25mm)

O.D.

1 3/4"

(51mm

)

(17mm)

(2mm) (44mm) (2mm)

1/4" (6mm)GLAZINGMATERIAL

3/8" (10mm)GLAZINGSPACE

5/8" (16mm)STEELMULLIONS(STD.)

Also Available using FGS-75 & BFL-123 profiles,

see pages 11 & 12 this section( )Mullions available in 1/2"x1/2" (13 x 13mm) or 1/2"x1" (13 x 25mm) steel tubing. Other tubing sizes available, consult factory.

Anemostat manufacturing dimensions 1/32 (0.79mm)Actual dimensions are nominal and may varybased on component manufacturers tolerances.

GLAZING: Should be 1/4" (6mm), 3/16" (5mm) or 5/16" (8mm) fire and/or safety rated with U.L. and/or W.H.I. classification markings. Nominal glazing space of 3/8" (10mm) allows for glazing tape to be used on both sides of the glass.

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.

MATERIAL: Frame is 20 GA. (1mm) Cold Rolled Steel. Mullions are 5/8" x 5/8" (16 x 16mm) steel tube material fully welded to the frame and to all intersecting points of the mullion design, and ground smooth.

INSTALLATION: Uses 1 3/4" (44mm) sheet metal screws that pass through the door cutout, and fastens the opposite side of the vision frame, thus eliminating the need to drill the door for thru bolts and saving installation time and labor. It also leaves the corridor side of the frame free of fasteners for added security and a cleaner, more aesthetic appearance.

IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.

NOTE: For Exterior use, High Humidity, or Salt Air applications,product must be Galvanized.

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


max. width 36" (914mm), max. height 54" (1372mm).90 MINUTE:* Approved listing at 1296 sq.in. (0.836 m2) visible lite

3 Hour:* Approved listing at 100 sq.in. (0.065m2) visible lite max. width 12" (305mm), max. height 33" (840mm)


45/60 MINUTE:* Approved listing at 2772 sq.in. (1.788 m2) visible litemax. width 36" (914mm), max. height 77" (1956mm).

OPTIONALMULLION

1" (25mm) WIDTH1/2" (13mm)


G-9000G-6000G-4000

G-3000G-2000

G-5000 G-6000 G-8000

G-1000 G-1200 G-1500

DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-GFRENCH DOOR LO-PROFILE

METAL VISION FRAME







Timber Doors - 30 min. and 1 hour.Steel Doors - 2 hours (4 hours actual).


■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836 m2) on20/45 min. and 100 sq. in. (0.065 m2) on 60/90/180 min., please consult withyour Door / Frame Manufacturer’s procedures, for their maximum glass sizetested.


For Most Current Info, Consult Factory or check our website, www.anemostat .comMAY 2014



FM-G is not Fire rated, and does not affect a fire-rated sidelite or borrowed lite.

SPECIALS: Choose from grille patterns as shown orFASTENERS: Special Security Screw Fasteners, see page 36, this section.

FINISH: Custom Baked Enamel Colors (as per sample chip supplied).


smooth instersections of all mullions. ProvidesAESTHETICS: Tight mitered corners, with welded and ground

GLAZING: Can be any thickness that provides a 3/4" (19mm) spacingdirectly to the hollow metal frame at 8" OC intervals.

INSTALLATION: Predrilled countersunk mounting holes allowFINISH: Grey Primer, Beige or Bronze Baked Enamel.

MATERIAL: Mullions are 3/4" x 3/4" (19 x 19mm) steel tube material welded at all intersecting points of the mullion design and at all corners.

allowance for Framed Mullions assembly.

Mullions available in 1/2"x1/2" (25 x 25mm), 5/8"x5/8" (16 x 16mm) or 1/2"x1" (13 x 25mm) steel tubing. Other tubing sizes available, consult factory.

create your own (not available round or curved).

NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized.

divided lite design to accent door or storefrontinstallation. (For Metal Vision Frames with mulliondesign, see LoPro-G, FGS-75-G, or BFL-123-G

ORDER SIZE&

SIDELITEFRAME

OPENING

Hollow MetalFrame

PREDRILLEDSCREW HOLES(8" OC)(203mm)

3/4"X3/4" STEEL TUBING(19mm)X(19mm)

STANDARD

MULLIONFRAMEO.D.

IS OR

DER S

IZE M

INUS 1

/8"

#8x1-1/2" (38mm) phillips head tek screws to fasten

on pages 8, 11, and 12 this section.)

Plated finishes to match the lock, hinges and closer.

IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.

OPTIONALMULLION

1" (25mm)WIDTH

1/2"(13mm)

1/2"(13mm)

1/2"(13mm)

OPTIONALMULLION

5/8"(16mm)

5/8"(16mm)

OPTIONALMULLION


G-9000G-6000G-4000

G-3000G-2000

G-5000 G-6000 G-8000

G-1000 G-1200 G-1500

TECHNICAL DATAFROM

DETAIL DRAWING

FM-GFRAMED MULLION

GRILLEFOR

SIDELITES ANDBORROWED LITES


FIRE RATINGS

NOT FIRE RATED






CUSTOM DESIGNS: (Drawing Required Please Specify ALL Dimensions)

PLEASE SIGN AND DATE. Order will not be processed until confirmation is received.

X

ORDER SIZE (Door Cutout *):

W___________ x H____________

VERTICAL MULLION(S) ________

HORIZONTAL MULLION(S) ______

QUANTITY:

_____________________________

* FMG - Order Size is Frame Opening

MULLION - Tubing Size5/8" x 5/8" (16 x 16mm)(LoPro™) std.3/4" x 3/4" (19 x 19mm)(BFL-FGS-FMG) std.1/2" x 1/2" (13 x 13mm)(various models)1/2" x 1" (13 x 25mm)(various models)Other _______ x _______ consult factory

MODELLoPro-G

FGS-G

BFL-123-G

BFL-75-G

FM-G

COMPANY NAME

E-MAIL

CUSTOMER CONTACT (Please Print)

CITY STATE

P.O. NUMBER FAX

JOB NAME ORDER MUST BE SIGNED

SIGNATURE DATE

DRAWING # __________________________Assigned by Factory

DETAIL DRAWING

TECHNICAL DATAFROM

CUSTOMMULLION DESIGNCONFIRMATION

SHEET__________ - G KITS

SPECIFY MODEL



INSIDE OUTSIDE

FRAMEO.D.

SPECIALS: Choose from grille patterns as shown or create your own.FASTENERS: Special Security Screw Fasteners, See Page 36, this section.

Plated Finishes to match the lock, hinges and closer.FINISH: Custom Baked Enamel Colors (as per sample chip supplied).


stop for maximum visible lite area.AESTHETICS: Tight mitered corners, 90° angle on glass

allows for glazing tape to be used on both sides of the glass.

GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire and/or safety rated with U.L. DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.

head on one side for flush appearance.#8x32 phillips head steel thru bolts with a blankFrame has countersunk mounting holes foraround the perimeter of the door cutout.

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, FINISH: Grey Primer, Beige or Bronze Baked Enamel.

MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.Mullions - are 3/4" x 3/4" (19 x 19mm) steel tube material fullywelded to the frame and to all intersecting points ofthe mullion design, and ground smooth.

and/or W.H.I. classification markings. Glazing space of 5/16" (8mm)


Available for thicker glass with 1/2" or 5/8" mullions.

( )Also Available usingLoPro & BFL-123 profiles, seepages 8 & 12 this section

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


3/4" (19mm)STEELMULLIONS(STD.)

Mullions available in 1/2"x1/2", 5/8"x5/8" or 1/2"x1" steel tubing.Other tubing sizes available, consult factory.


1/4"(6mm)

3/8"(10mm)

5/16"(8mm)GLAZINGSPACE

1 1/4"(32mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

ORDE

R SI

ZE P

LUS

1 1/

2"(3

8mm

)

1 3/4"(44mm)DOORONLY

1/4"(6mm)

1/4"(6mm)GLAZINGMATERIAL

OPTIONALMULLION

1" (25mm)WIDTH

1/2"(13mm)


G-9000G-6000G-4000

G-3000G-2000

G-5000 G-6000 G-8000

G-1000 G-1200 G-1500






DETAIL DRAWING

TECHNICAL DATAFROM

FGS-75-GFRENCH DOOR

METAL VISION FRAME



AUGUST 2013METAL VISION FRAMES PAGE 11


WARNOCK HERSEY

FIRERATINGS



■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836 m2) on 20/45 min. and 100 sq. in. (0.065 m2) on 60/90/180 min., please consult with yourDoor / Frame Manufacturer’s procedures, for their maximum glass size tested.






OPTIONALMULLION

1" (25mm)WIDTH

1/2"(13mm)


G-9000G-6000G-4000

G-3000G-2000

G-5000 G-6000 G-8000

G-1000 G-1200 G-1500

( )

SPECIALS: Choose from grille patterns as shown or create your own.FASTENERS: Special Security Screw Fasteners, see page 36.


allows for glazing tape to be used on both sides of the glass. GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire and/or safety rated with U.L. DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.

MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.Mullions - are 3/4" x 3/4" (19 x 19mm) steel tube material fully welded to the frame and to all intersecting points ofthe mullion design, and ground smooth.

and/or W.H.I. classification markings. Glazing space of 3/8" (10mm)

INSTALLATION: Uses 1 3/4" (44mm) sheet metal screws that pass through the door cutout, and fastens the opposite side of the vision frame, thus eliminating the need to drill the door for thrubolts and saving installation time and labor. It also leaves the corridor side of the frame free of fasteners for addedsecurity and a cleaner, more aesthetic appearance.

ORDE

R SI

ZE P

LUS

1" (2

5mm

)

O.D.FRAME

OUTSIDE

1/4"

INSIDEMI

NUS 1

" (25m

m)

ORDE

R SIZE

ISVIS

IBLE L

ITEPL

US 2"

(51m

m)

ORDE

R SIZE

ORDE

R SIZE

MINU

S 1/8"

(3mm

)

MIN

US 2

" (51

mm

)OR

DER

SIZE

1/4"(6mm)GLAZINGMATERIAL


ORDE

R SIZE

MINU

S 1 1/

2" (38

mm)

Also Available usingLoPro & FGS-75 profiles, seepages 8 & 11 this section


ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


1/4"DOOR

1 3/4"

ONLY

5/8"

1/4"

1 1/4"

(44mm)(6mm) (6mm)

(6mm)

(16mm)(32mm)

3/4" (19mm) STEELMULLIONS(STD.)

Mullions available in 1/2"x1/2" (13 x 13mm) , 5/8"x5/8" (16 x 16mm) or 1/2"x1" (13 x 25mm) steel tubing. Other tubing sizes available, consult factory.



DETAIL DRAWING

TECHNICAL DATAFROM

BFL-123-GFRENCH DOOR

METAL VISION FRAME






■ 20 MINUTE:* Approved listing at 3204 sq. in. (2.067 m2) visible lite.max. w 36" (914mm), max. h 89" (2261mm).

■ 45/60 MINUTE:* Approved listing at 2772 sq. in. (1.788 m2) visible lite.max. w 36" (914mm), max. h 77" (1956mm).

■ 90 MINUTE:* Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. w 36" (914mm), max. h 54" (1372mm).

■ 3 HOUR:* Approved listing at 100 sq. in. (0.065 m2) visible lite. max. w 12" (305mm), max. h 33" (838mm).

*Must be used with FIRELITE Plus or NT and Fire listed glazing tape or anothermanufacturer’s equivalent product. Glazing combination must be used inappropriately tested door assembly.

■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. on 20/45 min. and 100 sq. in. on 60/90/180 min., please consult with your Door / FrameManufacturer’s procedures, for their maximum glass size tested.


WARNOCK HERSEY

FIRERATINGS






1 3/4"(44mm)

1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

INSIDE OUTSIDE

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

ORDE

R SI

ZE P

LUS

1 1/

2"(3

8mm

)

FRAMEO.D.

DOORONLY

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil,Hot Dipped, or Zinc Plated), Aluminum Mill Finish (not fire rated)


FASTENERS: Special Security Screw Fasteners, See Page 36, this section. SPECIALS: Fractional Sizes, Lead Lined for X-ray applications,

Glass or Door thickness (see FGS-IS or FGS-DBL).

with U.L. and/or W.H.I. classification markings.

MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" holes thru the door, around the

perimeter of the door cutout.Frame has countersunk mounting holes for#8x32 phillips head steel thru bolts with a blank head on one side for flush appearance and added security.

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire and/or safety rated

Glazing space of 5/16" (8mm) allows for glazing tapeto be used on both sides of the glass.

AESTHETICS: Tight mitered corners, 90° angle on glass stopfor maximum visible lite area.

1/4"(6mm)

1/4"(6mm)

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE

GLAZINGMATERIAL




NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel. * Must be used with FIRELITE Plus or NT and Fire listed glazing tape or another

manufacturer’s equivalent product. Glazing combination must be used in appropriately tested door assembly.





DETAIL DRAWING

TECHNICAL DATAFROM

FGS-75METAL

VISION FRAME






■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. on 20/45 min. and 100 sq. in. on 60/90/180 min., please consult with your Door / FrameManufacturer’s procedures, for their maximum glass size tested. Timber Doors - 30 min. and 1 hour.

Steel Doors - 2 hours (4 hours actual).BS 476.22

British Standard


WARNOCK HERSEY

FIRERATINGS



For Most Current Info, Consult Factory or check our website, www.anemostat .comJULY 2011


INSIDE OUTSIDE

FRAMEO.D.

FGS-38 is not fire rated.

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil,Hot Dipped, or Zinc Plated).


FASTENERS: Special Security Screw Fasteners, See Page 36, this section.

SPECIALS: Fractional Sizes, Other Glass or Door thickness (see FGS-IS or LoPro™-IS).

MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door,

around the perimeter of the door cutout.Frame has countersunk mounting holes for#8x32 phillips head steel thru bolts with a blankhead on one side for flush appearance.

DOOR THICKNESS: For 1 3/8" (35mm) only.GLAZING: Should be 1/4" (6mm) safety rated.

Glazing space of 5/16" (8mm) allows for glazing tapeto be used on both sides of the glass.



1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

ORDE

R SI

ZE P

LUS

1 1/

2"(3

8mm

)


1/4"(6mm)

1/4"(6mm)

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE

GLAZINGMATERIAL

Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances. For Self-Attaching Installation see LoPro™-AB1-NR (page 2)


TECHNICAL DATAFROM

DETAIL DRAWING

FGS-38METAL

VISION FRAME

(1 3/8" DOORS)


FIRE RATINGS

NOT FIRE RATEDD o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219







MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (CoilHot Dipped, or Zinc Plated).


FASTENERS: Special Security Screw Fasteners, See Page 36, this section. SPECIALS: Fractional Sizes, Lead Lined for X-ray applications.

MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the

perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 phillips head steel thru bolts with a blank head on one side for flush appearance and added security.

DOOR THICKNESS: 1 3/4" (44mm) is standard. Specified up to 2 1/4" (57mm).



GLAZING: Thickness can range from over 3/16" (5mm) and up to 1 9/16" (40mm). Glazing space of 1/16" (2mm) over glass thickness is standard, allowing for glazing tape to be used on both sides of the glass. Glazing material should be fire and safety rated with U.L. and/or W.H.I. classification markings.

Must be 1/4" (6mm) minimum thicker than glass.


For mullions (see FGS-IS-G or LoPro™-IS-G).HM CLIP: Replaces the need for reinforcing channel

in the door cutout, see page 37 this section.

GLASSSIZE

ORDERSIZE

&DOOR

CUTOUT

MUSTSPECIFYGLASS

THICKNESS

VISIBLELITE

DOOR 1/4"1/4"

3/8"

1 1/4"

ORDE

R SI

ZE M

INUS

1"

INSIDE OUTSIDE

ORDE

R SI

ZE M

INUS

1/4

"

ORDE

R SI

ZE P

LUS

1 1/

2"

FRAMEO.D.

THICKNESS

THICKNESS GLASS OVER

1/16"SPACE

GLAZING

UP TO 2 1/4"(6mm) (6mm)

(10mm)

(32mm)

(25m

m)

(2mm)(6

mm

)

(57mm)

(38m

m)

DETAIL DRAWING

TECHNICAL DATAFROM

FGS-ISMETAL VISION FRAME FOR

SPECIAL GLASSOR DOOR THICKNESS





■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. on 20/45 min. and 100 sq. in. on 60/90/180 min., please consult with your Door / FrameManufacturer’s procedures, for their maximum glass size tested.


WARNOCK HERSEY

FIRERATINGS




■ 20/45/60/90 MINUTE:* Approved listing at 1080 sq. in. (0.697 m2) visible lite.max. width 36" (914mm), max. height 36" (914mm).

*Must be used with 7/8" (23mm) or 1-1/16" (27mm) Pyrostop and fire listed glazing tape, and be used in an appropriately tested door assembly.


■ 45/60 MINUTE:** Approved listing at 2772 sq. in. (1.788 m2) visible lite.max. w 36" (914mm), max. h 77" (1956mm).


■ 3 HOUR:** Approved listing at 100 sq. in. (0.065 m2) visible lite. max. w 12" (305mm), max. h 33" (838mm).

**Must be used with FIRELITE IGU 1" (25mm) Cat II or FIRELITE Plus and Fire listedglazing tape or another manufacturer’s equivalent product. Glazing combination mustbe used in appropriately tested door assembly.




WARNOCK HERSEY

FIRERATINGS

JULY 2011METAL VISION FRAMES PAGE 16

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil,Hot Dipped, or Zinc Plated).



SPECIALS: Fractional Sizes, Spacer between glass is available



DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.



FRAMEO.D.

INSIDE OUTSIDE

GLAZING: Should be two 1/4" (6mm) pieces separated by a 1/4" (6mm)spacer (spacer only furnished with vision frame).Glazing space of 1/16" (2mm) over glass and spacerthickness is standard, allowing for glazing tape

in other thicknesses, consult factory for information.

to be used on both sides of the glass.

1/4"(6mm)

3/8"(10mm)

13/16"(21mm)

GLAZINGSPACE

1 1/4"(32mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

ORDE

R SI

ZE P

LUS

1 1/

2"(3

8mm

)


1/4"(6mm)

DEAD AIRSPACE

1/4"(6mm)

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE

1/4"(6mm)

GLAZINGMATERIAL

1/4"(6mm)

GLAZINGMATERIAL


WELDED SPACER BAR


TECHNICAL DATAFROM

DETAIL DRAWING

FGS-DBLMETAL VISION FRAME

FORDOUBLE GLAZING





■ 20/45 MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372) , max. height 54" (1372).

■ 60/90 MINUTE: Approved listing at 100 sq. in. (0.065m2) visible lite.max. width 10" (254mm) , max. height 33" (838mm).



Glass or Door thickness (see FGS-IS or LoPro-IS).SPECIALS: Fractional Sizes, Lead Lined for X-ray applications,FASTENERS: Special Security Screw Fasteners, See Page 36, this section.


Hot Dipped, or Zinc Plated).MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil,

for a clean tapered look.AESTHETICS: Tight mitered corners, beveled glass stop

to be used on both sides of the glass. Glazing space of 3/8" (10mm) allows for glazing tape

GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire and/or DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.

INSTALLATION: Uses 1 3/4" (44mm) sheet metal screws that pass FINISH: Grey Primer, Beige or Bronze Baked Enamel.MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.

safety rated with U.L. and/or W.H.I. classification markings.

through the door cutout, and fastens to the oppositeside of the vision frame, thus eliminating the need to drillthe door for thru bolts and saving installation time andlabor. It also leaves the corridor side of the frame freeof fasteners for added security and a cleaner,more aesthetic appearance.

FRAME

ORDE

R SI

ZE P

LUS

1"

O.D.

OUTSIDE

1/4"

INSIDE

1/4"

ORDE

R SIZE

MINU

S 1/8"

PLUS

2"VIS

IBLE L

ITEOR

DER S

IZE IS

ORDE

R SIZE

MINU

S 1"

DOOR

1 3/4"

ONLY

MIN

US 2

"OR

DER

SIZE

1/4"

SPACEGLAZING

3/8"

MINU

S 1 1/

2"OR

DER S

IZE

5/8"

1/4"

1 1/4"

(25m

m)

(51mm

)

(3mm)

(25mm

)

(44mm)(6mm) (6mm)

(10mm)

(6mm)

(6mm)

(16mm) (32mm)

(51m

m)

(38mm

)


MATERIALGLAZING


ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


product must be Galvanized or Stainless Steel.NOTE: For Exterior use, High Humidity or Salt Air application,






DETAIL DRAWING

TECHNICAL DATAFROM

BFL-123METAL

VISION FRAME






■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836m2) on20/45 min. and 100 sq. in. (0.065m2) on 60/90/180 min., please consultwith your Door / Frame Manufacturer’s procedures, for their maximumglass size tested.


WARNOCK HERSEY

FIRERATINGS






ORDE

R SI

ZE P

LUS

1 3/

4"(4

4mm

)

FRAMEO.D.

INSIDE OUTSIDE

ORDE

R SI

ZEM

INUS

1 1

/2"

(38m

m)

Glass or Door thickness (see FGS-IS or LoPro-IS).SPECIALS: Fractional Sizes, Lead Lined for X-ray applications,FASTENERS: Special Security Screw Fasteners, See Page 36, this section.


Hot Dipped, or Zinc Plated).MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Coil,


to be used on both sides of the glass. Glazing space of 5/16" (8mm) allows for glazing tape

GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire and/or safety rated DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.


INSTALLATION: By drilling 1/4" (6mm) holes thru the door, FINISH: Grey Primer, Beige or Bronze Baked Enamel.MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.

with U.L. and/or W.H.I. classification markings.

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE





1 3/4"(44mm)1/4"

(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 3/16"(30mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

DOORONLY

1/4"(6mm)

1/4"(6mm)

GLAZINGMATERIAL






DETAIL DRAWING

TECHNICAL DATAFROM

BFL-75METAL

VISION FRAME







WARNOCK HERSEY

FIRERATINGS


■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836m2) on20/45 min. and 100 sq. in. (0.065m2) on 60/90/180 min., please consultwith your Door / Frame Manufacturer’s procedures, for their maximumglass size tested.




ORDE

R SI

ZE P

LUS

1 3/

4"(4

4mm

)

FRAMEO.D.

1/8"(3mm)

INSIDE OUTSIDE

GLASS SPACEAVAILABLE

(consult factory for FGS-IS-PO).SPECIALS: Fractional Sizes, Glass or Door thickness

See Page 36, this section.FASTENERS: Special Security Screw Fasteners,


Hot Dipped, or Zinc Plated).MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Coil,



about FGS-IS-PO.For a thicker glazing space, consult factory

GLAZING SPACE: Space allows for 1/8" (3mm) thick glazing material.DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.


INSTALLATION: By drilling 1/4" (6mm) holes thru the door, FINISH: Grey Primer, Beige or Bronze Baked Enamel.MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.

Can also be used without Glazing Material.

BFL-75-PO is not fire rated.

3/8"(10mm)

OPENING

FOR SPECIAL GLASS OR DOOR THICKNESSUSE FGS-IS-PO (CONSULT FACTORY)

12 X 6 IS STANDARD ORDER SIZEOTHER SIZES AVAILABLE, CONSULT FACTORY

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE


1 3/4"(44mm)1/4"

(6mm)

3/8"(10mm)

1 3/16"(30mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

DOORONLY

1/4"(6mm)


TECHNICAL DATAFROM

DETAIL DRAWING

BFL-75-POPOST OFFICE OBSERVATION

METALVISION FRAME


FIRE RATINGS

NOT FIRE RATED



2# LEAD LINING(1/32"/0.79mm)

Non-Screw Hole Side Onlyis Lead Lined

1/32"(0.79mm)

(TYP.)

4# LEAD LINING - Total(1/32"/0.79mm)Both Sides are Lead Lined with 2# Lead

X-RAY-SX-RAY & SAFETY

RATED GLASS5/16" (8mm) THICK

LoPro™LEAD LINED

METAL VISION FRAME

NOT FIRE RATED

For Complete Technical Data• LoProsee page 1, this section

• x-Ray-S Glasssee Glazing Products page 17

DETAIL DRAWING

TECHNICAL DATAFROM






4# LEAD LINING(1/16"/1.58mm)

FIRE & SAFETYRATED GLASS

1/4" (6mm) THICK

X-RAY-SX-RAY & SAFETY RATED GLASS5/16" (8mm) THICK

FGS-MS5-FRLEAD LINED / FIRE RATED

METAL VISION FRAMEIMPACT AND SECURITY RESISTANT

For Complete Technical Data• FGS-MSsee Security Products page 18

• Fire & Safety Rated Glasssee Glazing Products for selection

• x-Ray-S Glasssee Glazing Products page 17


WARNOCK HERSEY

FIRERATINGS

B.S.-476.22 British StandardDETAIL DRAWING

TECHNICAL DATAFROM






ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE



MATERIAL: 20 GA. (1mm) Zinc Plated Galvanized.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION:

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.GLAZING: Should be 1/4" (6mm) , 3/16" (5mm) or 5/16" (8mm)

fire and/or safety rated with U.L. and/or W.H.I. classification markings. Glazing space of 3/8" (10mm) allows for glazing tape to be used on both sides of the glass. See drawing above for details on other glass thicknesses available.

AESTHETICS: Smooth round contour of low profile frame stylegives a unique design to any setting.

NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized steel.

MATERIAL: #304 Stainless Steel, #4 Finish(Satin), Galvanized (Hot Dipped, or Zinc Plated),FINISH: Custom Baked Enamel Colors (as per sample chip supplied).

Plated Finishes to match the lock, hinges and closer.FASTENERS: Special Security Screw Fasteners,

See Page 36, this section.

20/45/60/90/180 MINUTE: Approved listing at 79 sq.in. (0.051 m2) visible lite.

Diameter

4 mounting holes per vision frame

10"(254mm)

FRAME

13" D

IAMET

ER (3

30mm

)

O.D.

12" D

IAMET

ER

OUTSIDE INSIDE

DOOR ONLY

11" D

IAMET

ER

(305m

m) (280m

m)

(2mm) (44mm)

(254m

m)

1" (25mm)

1/2" (13mm)

1/4"

MATERIALGLAZING(6mm)


10" D

IAMET

ER

(2mm)

(17mm)11/16"

5/64" 1 3/4" 5/64"

Uses #8 x 1 3/4" (44mm) long phillips oval head screws that pass through the door cutout and fasten to the opposite side of the vision frame, eliminating the need for thru bolts.


VisibleGlass

A B1

B B1

A, B = Non Screw Side of FrameA1, B1 = Screw Side of Frame

Lo-FP-12-AB1

Lo-FP-12-BB1

Lo-FP-12-AA11-3/4" Door

(44mm)

1-3/4" Door(44mm)

3/4"(19mm)

GLAZINGSPACE

5/8" to 11/16"(16mm to 17mm)

GLAZINGTHICKNESS

1 1/16(27mm)

GLAZINGSPACE

7/8" to 1"(22mm to 25mm)

GLAZINGTHICKNESS

3 Hour:* Approved listing at 79 sq.in. (0.051 m2) visible lite* Must be used with FIRELITE Plus or NT and Fire listed glazing tape or another


DETAIL DRAWING

TECHNICAL DATAFROM

Lo-FP-12Lo-FP-12-IS12" (305mm) ROUND

LO-PROFILE METAL VISION FRAME





WARNOCK HERSEY



FIRERATINGS









MATERIAL: #304 Stainless Steel, #4 Finish(Satin), Galvanized (Hot Dipped, or Zinc Plated).FINISH: Custom Baked Enamel Colors (as per sample chip supplied).

Plated Finishes to match the lock, hinges and closer.FASTENERS: Special Security Screw Fasteners, See Page 36, this section.

20/45/60*/90* MINUTE: Approved listing at 201 sq.in. (0.13 m2) visible lite.

FRAME

19" D

IAMET

ER (4

83mm

)

O.D.

18" D

IAMET

ER

OUTSIDE INSIDE

DOOR ONLY

17" D

IAMET

ER

(457m

m) (432m

m)

(2mm) (44mm)

(406m

m)

1" (25mm)

1/2" (13mm)

1/4"

MATERIALGLAZING

(6mm)


16" D

IAMET

ER

(2mm)

(17mm)11/16"

5/64" 1 3/4" 5/64"

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE



MATERIAL: 20 GA. (1mm) Zinc Plated Galvanized.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION:

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.GLAZING: Should be 1/4" (6mm), 3/16" (5mm) or 5/16" (8mm)

fire and/or safety rated with U.L. and/or W.H.I. classification markings. Glazing space of 3/8" (10mm) allows for glazing tape to be used on both sides of the glass. See drawing above for details on other glass thicknesses available.



Uses #8 x 1 3/4" (44mm) long phillips oval head screws that pass through the door cutout and fasten to the oppositeside of the vision frame, eliminating the need for thru bolts.

VisibleGlass



Diameter

16"(406mm)

A B1

B B1

Lo-FP-18-AB1

Lo-FP-18-BB1

Lo-FP-18-AA1

A, B = Non Screw Side of FrameA1, B1 = Screw Side of Frame

1-3/4" Door(44mm)

1-3/4" Door(44mm)

3/4"(19mm)

GLAZINGSPACE

5/8" to 11/16"(16mm to 17mm)

GLAZINGTHICKNESS

1 1/16(27mm)

GLAZINGSPACE

7/8" to 1"(22mm to 25mm)

GLAZINGTHICKNESS


DETAIL DRAWING

TECHNICAL DATAFROM













Lo-FP-18Lo-FP-18-IS18" (457mm) ROUND



WARNOCK HERSEY



FIRERATINGS



MATERIAL: 20 GA. (1mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Uses #8 x 1 3/4" (44mm) long phillips oval head

screws that pass through the door cutout and fasten to the opposite side of the vision frame, eliminating the need for thru bolts.

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.GLAZING: Should be 1/4" (6mm), 3/16" (5mm) or 5/16" (8mm) fire and/or

safety rated with U.L. and/or W.H.I. classification markings. Glazing space of 3/8" (10mm) allows for glazing tape to be used on both sides of the glass.





20/45/60*90* MINUTE: Approved listing at 380 sq.in. (0.25m2) visible lite.


FRAME

25" D

IAMET

ER (6

35mm

)

O.D.

24" D

IAMET

ER

OUTSIDE INSIDE

DOOR ONLY

23" D

IAMET

ER

(610m

m) (584m

m)

(2mm) (44mm)

(559m

m)

1" (25mm)

1/2" (13mm)

1/4"

MATERIALGLAZING

(6mm)


22" D

IAMET

ER

(2mm)

(17mm)11/16"

5/64" 1 3/4" 5/64"

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


MATERIAL: Galvanized (Hot Dipped, or Zinc Plated).

VisibleGlass


Diameter

22"(559mm)

DETAIL DRAWING

TECHNICAL DATAFROM

Lo-FP-2424" ROUND






WARNOCK HERSEY



FIRERATINGS












11" D

IAM

ETER

(279

mm

)

11 3

/4" D

IAM

ETER

(298

mm

)

12" D

IAM

ETER

(305

mm

)

13 1

/2" D

IAM

ETER

(343

mm

)

FRAMEO.D.

INSIDE OUTSIDE



DOOR THICKNESS: For 1 3/4" (44mm) Wood and Metal Doors.GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire and/or safety rated with

U.L. and/or W.H.I. classification markings. Glazing space of 5/16" (8mm) allows for glazing tape to be used on both sides of the glass.

AESTHETICS: Smooth round contour of frame stylegives a unique design to any setting.


MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized(Hot Dipped, or Zinc Plated).



SPECIALS: Consult Factory for special diameter sizes

Diameter


11"(279mm)

and special glass or door thicknesses.

1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)


1/4"(6mm)

1/4"(6mm)


ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE

GLAZINGMATERIAL


VisibleGlass

20/45/60*90* MINUTE: Approved listing at 79 sq.in. (0.051m2) visible lite.* Must be used with FIRELITE Plus or NT and Fire listed glazing tape or another


DETAIL DRAWING

TECHNICAL DATAFROM

FP-1212" ROUND

METAL VISION FRAME







WARNOCK HERSEY

FIRERATINGS






FRAMEO.D.

INSIDE OUTSIDE




with U.L. and/or W.H.I. classification markings. Glazing space of 5/16" (8mm) allows for glazing tape to be used on both sides of the glass.



MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Hot Dipped, or Zinc Plated).



SPECIALS: Consult Factory for special diameter sizesand special glass or door thicknesses.

17" D

IAM

ETER

(432

mm

)

20/45/60*/90* MINUTE: Approved listing at 201 sq.in. (0.13m2) visible lite.


VisibleGlass

8 mounting holes per vision frameAnemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.

Diameter

17"(432mm)

17 3

/4" D

IAM

ETER

(451

mm

)

18" D

IAM

ETER

(457

mm

)

19 1

/2" D

IAM

ETER

(495

mm

)

1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)


1/4"(6mm)

1/4"(6mm)

GLAZINGMATERIAL

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


DETAIL DRAWING

TECHNICAL DATAFROM

FP-1818" ROUND

METAL VISION FRAME









WARNOCK HERSEY

FIRERATINGS





FRAMEO.D.

INSIDE OUTSIDE




with U.L. and/or W.H.I. classification markings. Glazing space of 5/16" (8mm) allows for glazing tape to be used on both sides of the glass.



MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Hot Dipped or Zinc Plated).



SPECIALS: Consult Factory for special diameter sizes


and special glass or door thicknesses.

20/45/60*/90* MINUTE: Approved listing at 380 sq.in. (.025m2) visible lite.


VisibleGlass

Diameter

23"(584mm)

23 3

/4" D

IAM

ETER

(603

mm

)

24" D

IAM

ETER

(610

mm

)

25 1

/2" D

IAM

ETER

(648

mm

)

1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)


1/4"(6mm)

1/4"(6mm)

23" D

IAM

ETER

(584

mm

)

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE


GLAZINGMATERIAL


DETAIL DRAWING

TECHNICAL DATAFROM

FP-2424" ROUND

METAL VISION FRAME









WARNOCK HERSEY

FIRERATINGS








Some examples are shown below, for other designs consult factory.

Recommendation: Do Not make Cutouts in Doors prior to receiving Custom Shaped Vision Frame

CHRISTIAN CROSS HEXAGON

KITE

TRIANGLE

TRIANGULAR TOP

ISOSCELES TRAPEZOID

TRAPEZOID OCTAGON

MUST SPECIFY HANDINGIF NOT EQUILATERAL




* Above designs are manufactured using LoProvision frames. For other applications or shapesPlease consult factory, or submit desired design.




WARNOCK HERSEY



FIRERATINGS


TECHNICAL DATAFROM

DETAIL DRAWING

LoPro™-CSNON-CURVED

CUSTOM SHAPES






Timber Doors - 30 min. and 1 hour. Tested to 254mm x 762mmSteel Doors - 2 hours (4 hours actual). Tested to 813mm x 813mm


AVAILABILITY: Non-Curved - A, B, C, D, E Profiles (see LoPro-IS Style page 2, this section)

■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836 m2)on 20/45 min. and 100 sq. in. (0.065 m2) on 60/90/180 min., pleaseconsult with your Door / Frame Manufacturer’s procedures, for theirmaximum glass size tested.








Some examples are shown below (based on 3-0 x 7-0 door), for other designs consult factory.

Recommendation: Do Not make Cutouts in Doors prior to receiving Custom Shaped Vision FrameQR-12 QR4C-6 HCTB-12 HC-24-G4

HCT-18 QR1C-9 QR2C-6QR2C-12



NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized.Curved Products NOT AVAILABLE in Stainless Steel.

* Above designs are manufactured using LoPro & LoFP-12, 18, 24 vision frames. For other applications or shapes Please consult factory, or submit desired design.




WARNOCK HERSEY



FIRERATINGS


TECHNICAL DATAFROM

DETAIL DRAWING

LoPro™-CSCURVED

CUSTOM SHAPES




Timber Doors - 30 min. and 1 hour. Tested to 254mm x 762mmSteel Doors - 2 hours (4 hours actual). Tested to 813mm x 813mm


AVAILABILITY: Curved - A Profile (12, 18 & 24 Diameters)- B Profile (12 & 18 Diameters) See Reference Sheets pages 30 & 31

■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836 m2)on 20/45 min. and 100 sq. in. (0.065 m2) on 60/90/180 min., pleaseconsult with your Door / Frame Manufacturer’s procedures, for theirmaximum glass size tested.



DOORCUTOUT/ORDER

SIZEDOOR CUTOUT/

ORDER SIZEDOOR CUTOUT/

ORDER SIZE

VISIBLELITE

VISIBLE LITE

VISIBLELITE

VISIBLELITE

DOORCUTOUT/ORDER

SIZEDOOR CUTOUT/

ORDER SIZEDOOR CUTOUT/

ORDER SIZE

VISIBLELITE

VISIBLELITE

VISIBLELITE

12"(305mm)

18"(457mm)

24"(610mm)

DOORCUTOUT/ORDER

SIZE

DOOR CUTOUT/ORDER SIZE

VISIBLE LITE

DOOR CUTOUT/ORDER SIZE

VISIBLE LITE

SPECIFY

SPECIFY

6" (152mm)CUTOUTHEIGHT

9" (229mm)CUTOUTHEIGHT

12"CUTOUTHEIGHT

HC-12 HC-18HC-24

HCT-12 HCT-18 HCT-24

HCTB-12 HCTB-18 HCTB-24

10"(254mm)

12"(305mm)

10"(254mm)

12"(305mm)

10"(254mm)

16"(406mm)

18"(457mm)

16"(406mm)

18"(457mm)

16"(406mm)

22"(559mm)

24"(610mm)

22"(559mm)

24"(610mm)

22"(559mm)

3"(76mm)

MIN

3"(76mm)

MIN


DETAIL DRAWING

REFERENCE SHEETFROM

LoPro™-CS-HCHALF CIRCLE

CUSTOM SHAPESMANUFACTURED FROM:LOFP-12 AA1, AB1, BB1LOFP-18 AA1, AB1, BB1LOFP-24 AA1



6"(152mm)RADIUS

9" (229mm)RADIUS

12" (305mm)RADIUS

3" (76mm)MIN

3" (76mm)MIN

3" (76mm)MIN

6"(152mm)

9"(229mm)

SPECIFY

SPECIFY

6"9"

12" 12"9"

6"

MIN WIDTH / HEIGHT15" (381mm)



6"9"

12"

QR-6 QR-9QR-12

QR4C-6 QR4C-9 QR4C-12

QR2C-6 QR1C-6 QR2C-9 QR1C-9 QR2C-12 QR1C-12

6"(152mm)

9"(229mm)

12"(305mm)

12"(305mm)

6"(152mm)RADIUS

9"(229mm)RADIUS

12"(305mm)RADIUS

3"(76mm)

MIN

3"(76mm)

MIN

3"(76mm)

MIN


DETAIL DRAWING

REFERENCE SHEETFROM

LoPro™-CS-QRQUARTER RADIUSCUSTOM SHAPESMANUFACTURED FROM:LOFP-12 AA1, AB1, BB1LOFP-18 AA1, AB1, BB1LOFP-24 AA1









Recommendation: Do Not make Cutouts in Doors prior to receiving Custom Shaped Vision FrameAMERICA

ELONGATEDHEXAGON

CHRISTIAN CROSS

Some examples are shown below, for other designs consult factory. All Below are also available in LoPro-CS, see page 28



NOTE: For Exterior use, High Humidityor Salt Air application,product must be Galvanized or Stainless Steel.

* Above designs are manufactured using FGS-75 vision frame. For other applications or shapes Please consult factory, or submit desired design.

Most products can also be manufactured using LoPro™ (self attaching) profile. Specify LoPro-CS.For Special Paint, Metal, Glass or Door thickness, consult factory.

DIAMOND 4 LITETRAPEZOID TOP

ISOSCELES TRAPEZOID

CHAMPAGNEINDIANA

TECHNICAL DATAFROM

DETAIL DRAWING

FGS-75-CSCUSTOM SHAPESMETAL VISION FRAMES





WARNOCK HERSEY

FIRERATINGS




PLEASE NOTE: Custom Shaped Curved Products are NOT AVAILABLE in FGS-75-CS

■ PLEASE NOTE: On visible lite sizes larger than 1296 sq. in. (0.836 m2) on 20/45 min. and 100 sq. in. (0.065 m2) on 60/90/180 min., please consult with yourDoor / Frame Manufacturer’s procedures, for their maximum glass size tested.




#8-32X1-1/4" (32mm) SCREW WITH THRU BOLT, BLANK ONE ENDUSED FOR: FGS-75, FGS-IS, FGS-38, FGS-75-G, FGS-DBL, FGS-75-RFGS-75-RC, FGS-75-RD, FGS-75-CS, FP-12, FP-18, FP-24, BFL-75, BFL-75-PO

Consult Factory for Price and Availability.Screw drivers and insert bits for Security Fasteners are available.*

NOTCHED SPANNER

ONE WAY VANDAL PROOF

SNAKE EYE SPANNER TORX FLAT HEAD

TORX-PLUS FLAT HEAD

PINNED FLAT HEAD

BFL-123#8X1-1/2" (38mm)#8X2" (51mm)

#8X1-1/2" (38mm)#8X2" (51mm)

FGS #8-32X1-1/4" (32mm)

#8X1-1/2" (38mm)#8X2" (51mm)#8-32X1-1/4" (32mm)

#8X2" (51mm)#8-32X1-1/4" (32mm)

FGS

FGS

LoProTM

BFL-123TM

LoPro

BFL-123TMLoPro

BFL-123TMLoPro

FGS #8-32X1-1/4" (32mm)#8X1-1/2" (38mm)TMLoPro

BFL-123#8X1-3/4" (44mm)LoProTM

#8X1-3/4" (44mm) SHEET METAL SCREWUSED FOR: LoPro™, LoPro™-IS, LoPro™-G, LoPro™-R, LoPro™-RC, LoPro™-RD, LoPro™-CS, LoPro™-STC, LoPro™-BB1-MB, Lo-FP-12, Lo-FP-18, Lo-FP-24, StormPro-HR™, StormPro-HR™-G, WoodPro#8X2" SHEET METAL SCREWUSED FOR: BFL-123-G

#8X1-1/2" (38mm) SHEET METAL TEK SCREWUSED FOR: FM-G

3/8" (10mm)

#8X1-1/2" (38mm)#8X2" (51mm)

STANDARD

*OPTIONAL SECURITY FASTENERS

OPTIONAL SCREW (Same upcharge as security screws)

#8X1-1/2" (38mm) SQUARE DRIVE (ROBERTSON HEAD)

USED FOR: LoPro, BFL-123TM

SHEET METAL SCREW

STANDARD

(Consult Factory for Stainless Steel Availability)

TECHNICAL DATAFROM

DETAIL DRAWING

FASTENERSFOR

METAL VISION FRAMESD o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219




1/4"(6mm)

20/45/60/90 minutes listing approval from Underwriters Laboratory

- One HM-Clip required on cutout sides 30" (762mm) to 60" (1524mm)For Lites over 100 sq.in. visible lite.No clips required for 100 sq.in. Anemostat Visible Lite Frames.

Replaces the need for reinforcing channel in allUSES: For use in Hollow Metal Door.DOOR THICKNESS: For 1 3/4" (44mm) Door only.

PURPOSE: Prevents hollow metal door from collapsing when coresnap into place, fitting flush with the door cutout.

INSTALLATION: Put long bent side of clip between door skins, then MATERIAL: 20 GA. (1mm) Cold Rolled Steel.

and Warnock Hersey for use on all Anemostat Vision Frames

burns away during a fire.

Anemostat Vision Frames and the FLDL-UL fusiblelink louver.

centered in side (minimum U.L. requirements).- Two HM-Clips required on cutout sides over 60" (1524mm),

equally spaced in side (minimum U.L. requirements).

and the FLDL-UL Louver.

18 GA. (1.25mm) HOLLOW METAL DOOR

DOOR CUTOUTFOR

VISION FRAME

PLEASE NOTE: When using HM-CLIPS with LoPro™ series vision frames extra caution should be taken to ensure door cut-out is exact – DO NOT OVERSIZE CUT-OUT!


1 11/16

(43mm)

1 13/16

(46mm)

11/16(17mm)

DETAIL DRAWING

TECHNICAL DATAFROM

HM-CLIPHOLLOW METAL

DOOR CLIP





WARNOCK HERSEY

FIRERATINGSD o o r P r o d u c t s

4958 Stout Dr. #119, San Antonio, TX 78219PH: 210.662.6300 • FAX: 210.662.2828

e-mail: [email protected] • website: www.anemostat.com FOR USE WITH ANEMOSTAT PRODUCTS

Documents

Door Products VISION FRAMES - Anemostat · Door Products 4958 Stout Dr. #119, San Antonio, TX 78219 PH: 210.662.6300 • FAX: 210.662.2828 e-mail: [email protected] • website: