DOC273.52.00152.Jul07 Tank wall mount kit LZX414.00 - Hach

DOC273.52.00152.Jul07

Tank wall mount kit LZX414.00.70000Instruction Sheet

Edition 1 July 2007 wc/kt

© HACH LANGE GmbH, 2007. All rights reserved. Printed in Germany.

DOC273.52.00152.Jul07
Instruction Sheet Tank wall mount kit LZX414.00.70000
IntroductionThis instruction sheet describes how to install tank wall mount kit LZX414.00.70000.

Items supplied with LZX414.00.70000Items supplied with the tank wall mount kit are shown in Figure 1 on page 1. Figure 2 on page 2 shows the dimensions of the mount kit components. Installation dimensions are shown in Figure 3 on page 3.

Figure 1 Items supplied with the tank wall mount kit1

1 Mount pipe (2 m) (Cat. No. BRO075) 13 Washer (4x)

2 Tank wall mount for SONATAX sc (Cat. No. LZY370) 14 Quick-fit anchor (4x)

3 Base (Cat. No. ATS012) 15 Plug (Cat. No. LZX909)

4 Fastening lug 16 Set of cap screws (Cat. No. LZY429)

5 Pipe bracket (Cat. No. LZY449) (2x) 17 Cap screw M8 x 30 mm (4x)

6 Bracket, threaded 18 Washer for M8 (4x)

7 Bracket, unthreaded 19 Set of cap screws (Cat. No. LZY362)

8 Set of cap screws (Cat. No. LZY445) 20 Cap screw M5 x 12 mm (7x)

9 Cap screw M5 x 20 mm (3x) 21 Spring washer for M5 (7x)

10 Washer for M5 (3x) 22 Hex wrench 4 mm

11 Set of quick-fit anchors (Cat. No. LZY428) 23 Sealing plug (Cat. No. LZX908)

12 Nut M8 (4x) 24 O-ring for SONATAX sc (Cat. No. LZY453)

1 Items supplied are subject to change without notice.

1

Tank wall mount kit LZX414.00.70000

Figure 2 Dimensions

2


Select the install locationImportant Note: When installing the SONATAX sc, observe all hazard and safety instructions, particularly the information on selecting the measuring location and instrument setup in the SONATAX sc user manual.

Note: When selecting the install location, always make sure there is safe access to all parts of the system and that the SONATAX sc can never hit the tank wall.

During the selection of the install location, pay attention to:

• The load bearing capacity and strength of the tank wall (lever forces due to flow and installation)

• The maximum cable and tubing lengths

Note: Refer to the SONATAX sc user manual for operating instructions.

Figure 3 Installation dimensions

3


Install the tank wall mount

1. Find a suitable installation location and install the quick-fit anchors.

Note: Drill accurate holes so that the fastening lug is exactly vertical.

a. Drill the holes (see Figure 4 on page 5) and insert the quick-fit anchors.

b. Hit the head of the quick-fit anchor with a hammer to make the quick-fit anchor spread in the hole.

Note: Only tighten the nuts after the base and fastening lug have been assembled and aligned.

2. Attach the base to the quick-fit anchors using four M8 nuts and washers (see Figure 5 on page 5). Tighten the nuts by hand.

3. Attach the fastening lug to the base using four cap screws (M8 x 30 mm) and washers (see Figure 6 on page 6).

4. Align base and fastening lug vertically and tighten all screws.

Note: If the wall is not exactly vertical, place shims behind the base at the top or bottom and then tighten.If the fastening lug is not vertical, move the base and the fastening lug a few degrees in the holes.

5. Loosely bolt the threaded brackets using cap screws (M5 x 20 mm) and spring washers for M5 to the unthreaded brackets on the mount pipe (see Figure 7 on page 6). During this process pay attention to the installation dimensions (see Figure 3 on page 3).

CAUTIONRisk of injury. Tighten the screws sufficiently so that the brackets cannot slide off the mount pipe.

6. Based on the local conditions and the immersion depth required (see operating instructions for SONATAX sc) determine the installation position for the two top brackets and slide the mount pipe with the brackets installed on the fastening lug.

Note: The flange on the mount pipe should be approximately 3–5 cm under the surface of the water so that the sensor always remains immersed while measurements are made.

7. Check the dimensions and tighten all screws.

8. To attach the sensor, remove the mount pipe from the fastening lug (see Attach the SONATAX sc on page 7).

4


Figure 4 Install the quick-fit anchors

Figure 5 Attach the base1 Nut M8 3 Base

2 Washer for M8 4 Quick-fit anchor

5


Figure 6 Attach the fastening lug1 Cap screw M8 x 30 mm 4 Quick-fit anchor

2 Washer 5 Base

3 Fastening lug

Figure 7 Attach the mount pipe with the brackets1 Threaded bracket 3 Unthreaded bracket

2 Mount pipe

6


Attach the SONATAX sc

1. Slide the O-ring over the sensor cable.

2. Slide the sensor cable through the mount pipe from below and bolt the pipe flange to the sensor using the cap screws (M5 x 12 mm) and the spring washers for M5 (see Figure 8 on page 7).

3. Insert a plug and a sealing plug in the top of the mount pipe. If necessary, shorten the pipe and then insert the plugs.

Figure 8 Attach the SONATAX sc1 Sealing plug 5 Cap screw M5 x 12 mm

2 Plug 6 Washer

3 Sensor cable 7 O-ring

4 Mount pipe 8 SONATAX sc

7


Attach sensor assembly to mount

1. Slide the two brackets (attached to mount pipe and sensor) over the fastening lug and align all the parts, taking into account the installation dimensions and the local conditions (Figure 9 on page 8). Check the position of the sensor in the tank and tighten all screws.

2. Route the sensor cable to the controller and attach the quick-connect fitting.

3. Continue as described in the operating instructions for the SONATAX sc and the controller.

Figure 9 Tank wall mount assembled (without sensor)

8


Replacement parts and accessoriesDescription Quantity Cat. No.

Base 1 ATS012

Bracket for pipes 1 LZY449

Mount pipe (2 m) 1 BRO075

Plug 1 LZX909

O-ring 1 LZY453

Seal plug 1 LZX908

Set of cap screws M5 x 12 mm 1 LZY362



Set of quick-fit anchors 1 LZY428

Tank wall mount for SONATAX sc 1 LZY370

9

Contact information

HACH CompanyWorld HeadquartersP.O. Box 389Loveland, Colorado80539-0389 U.S.A.Tel (800) 227-HACH(800) -227-4224(U.S.A. only)Fax (970) [email protected]

Repair Service in theUnited States:HACH CompanyAmes Service100 Dayton AvenueAmes, Iowa 50010Tel (800) 227-4224(U.S.A. only)Fax (515) 232-3835

Repair Service in Canada:Hach Sales & ServiceCanada Ltd.1313 Border Street, Unit 34Winnipeg, ManitobaR3H 0X4Tel (800) 665-7635(Canada only)Tel (204) 632-5598Fax (204) [email protected]

Repair Service inLatin America, the Caribbean, the Far East, Indian Subcontinent, Africa, Europe, or the Middle East:Hach Company WorldHeadquarters,P.O. Box 389Loveland, Colorado,80539-0389 U.S.A.Tel +001 (970) 669-3050Fax +001 (970) [email protected]

HACH LANGE GMBHWillstätterstraße 11D-40549 DüsseldorfTel. +49 (0)2 11 52 88-320Fax +49 (0)2 11 52 [email protected]

HACH LANGE LTDPacific WaySalfordGB-Manchester, M50 1DLTel. +44 (0)161 872 14 87Fax +44 (0)161 848 73 [email protected]

HACH LANGE LTDUnit 1, Chestnut RoadWestern Industrial EstateIRL-Dublin 12Tel. +353(0)1 46 02 5 22Fax +353(0)1 4 50 93 [email protected]

DR. BRUNO LANGE GES. MBHIndustriestraße 12A-3200 ObergrafendorfTel. +43 (0)27 47 74 12Fax +43 (0)27 47 42 [email protected]

DR. BRUNO LANGE AGJuchstrasse 1CH-8604 HegnauTel. +41(0)44 9 45 66 10Fax +41(0)44 9 45 66 [email protected]

HACH LANGE FRANCE S.A.S.33, Rue du BallonF-93165 Noisy Le GrandTél. +33 (0)1 48 15 68 70Fax +33 (0)1 48 15 80 [email protected]

HACH LANGE SAMotstraat 54B-2800 MechelenTél. +32 (0)15 42 35 00Fax +32 (0)15 41 61 [email protected]

DR. LANGE NEDERLAND B.V.Laan van Westroijen 2aNL-4003 AZ TielTel. +31(0)344 63 11 30Fax +31(0)344 63 11 [email protected]

HACH LANGE APSÅkandevej 21DK-2700 BrønshøjTel. +45 36 77 29 11Fax +45 36 77 49 [email protected]

HACH LANGE ABVinthundsvägen 159ASE-128 62 SköndalTel. +46 (0)8 7 98 05 00Fax +46 (0)8 7 98 05 [email protected]

HACH LANGE S.R.L.Via Riccione, 14I-20156 MilanoTel. +39 02 39 23 14-1Fax +39 02 39 23 [email protected]

HACH LANGE S.L.U.Edif. Arteaga CentrumC/Larrauri, 1C- 2ª Pl.E-48160 Derio/VizcayaTel. +34 94 657 33 88Fax +34 94 657 33 [email protected]

HACH LANGE LDAAv. do Forte nº8Fracção MP-2790-072 CarnaxideTel. +351 214 253 420Fax +351 214 253 [email protected]

HACH LANGE SP.ZO.O.ul. Opolska 143 aPL-52-013 WrocławTel. +48 (0)71 342 10-83Fax +48 (0)71 342 [email protected]

HACH LANGE S.R.O.Lešanská 2a/1176CZ-141 00 Praha 4Tel. +420 272 12 45 45Fax +420 272 12 45 [email protected]

HACH LANGE S.R.O.Roľnícka 21SK-831 07 Bratislava – VajnoryTel. +421 (0)2 4820 9091Fax +421 (0)2 4820 [email protected]

HACH LANGE KFT.Hegyalja út 7-13.H-1016 BudapestTel. +36 (06)1 225 7783Fax +36 (06)1 225 [email protected]

HACH LANGE S.R.L.Str. Leonida, nr. 13Sector 2RO-020555 BucurestiTel. +40 (0) 21 201 92 43Fax +40 (0) 21 201 92 [email protected]

HACH LANGE8, Kr. Sarafov str.BG-1164 SofiaTel. +359 (0)2 963 44 54Fax +359 (0)2 866 04 [email protected]

HACH LANGE SUANALİZ SİSTEMLERİ LTD.ŞTİ.Hilal Mah. 75. SokakArman Plaza No: 9/ATR-06550 Çankaya/ANKARATel. +90 (0)312 440 98 98Fax +90 (0)312 442 11 [email protected]

HACH LANGE D.O.O.Fajfarjeva 15SI-1230 DomžaleTel. +386 (0)59 051 000Fax +386 (0)59 051 [email protected]

ΗΑCH LANGE E.Π.Ε.Αυλίδος 27GR-115 27 ΑθήναΤηλ. +30 210 7777038Fax +30 210 [email protected]

HACH LANGE E.P.E.27, Avlidos strGR-115 27 AthensTel. +30 210 7777038Fax +30 210 [email protected]

Documents

DOC273.52.00152.Jul07 Tank wall mount kit LZX414.00 - Hach