Upload
budy-andika
View
211
Download
0
Embed Size (px)
Citation preview
Standard cylinders DNC, ISO 15552
-V- NewBellows DADB Standard cylinders DNC, ISO 15552Key features At a glance
DIN
Standards-based cylinders to ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA 24 562, NF E 49 003.1 and UNI 10290)
The modern design and construction save up to 11% on fitting space compared to ordinary standard cylinders, thus permitting a considerably more compact system design
An extensive range of accessories makes it possible to install the cylinder virtually anywhere The widest range of variants on the market provides the right DNC cylinder for every application
Cylinder with clamping units DNC-KP Piston rod can be held or clamped in any position Piston rod can be held in position for long periods even with alternating loads, fluctuating operating pressure or leaks in the system Cylinder with end-position locking DNC- -EL Mechanical locking when the end position is reached Lock is only automatically released when pressure is supplied to the cylinder End-position locking at one or both ends
DNCKE Suitable for use in safety-related control systems in compliance with EN 954-1, EN 1050, EN 292 and EN 983 Fail-safe Piston rod can be clamped in any position Cylinder/valve combination DNC-V1 V6 The cylinder/valve combination is assembled and fitted with tubing ready for connection Particularly suitable for decentralised use in larger systems
Tandem cylinder DNCT Connection of 2 cylinders with the same piston diameter and stroke in series Double the thrust and return force in comparison to a standard cylinder
Longer service life thanks to the bellows kit DADB The bellows kit is a leak-free system. To prevent unwanted media being drawn in, the supply and exhaust air must be ducted via a venting hole in the connection part 1. The kit protects the piston rod, seal and bearings from a wide range of media, for example: dust, chips, oil, grease, fuel.
1
2
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Key features Variants from the modular product system Symbol Key features S2 S6 S10 Through piston rod Heat-resistant seals Constant motion (slow speed) at low piston speeds Low friction
Description For working at both ends with the same force in the forward and return stroke, for attaching external stops Temperature resistance up to max. 120 C Suitable for slow stroke movements at a constant, stick-slip-free speed over the full stroke of the cylinder. Seal contains silicone grease (not free of paint-wetting impairment substances) Special seals considerably reduce system wear. This means a considerably lower response pressure. Seal contains silicone grease (not free of paint-wetting impairment substances) For supplying vacuum, small parts, media, etc. Metric standard thread to ISO Special spanner flats Ideal for use in welding environments: Protection against welding spatter Small working loads Harder surface compared to steel Long service life Integrated clamping unit on the piston rod Positive locking in the end position as a drop guard. If there is a drop in pressure, the piston rod is secured in its end position to prevent it from dropping Protection against rotation. For correctly oriented feeding All external cylinder surfaces comply with corrosion resistance class 3 to Festo standard 940 070. The piston rod is made from corrosion and acid-resistant steel The cylinder is equipped with a hard-chrome plated piston rod and a rigid wiper seal, which protects against dry, dusty media Temperature resistance down to max. 40 C
S11
S20 K2 K3 K5 K7 K8 K10
Through, hollow piston rod Extended male piston rod thread Female piston rod thread Special piston rod thread Piston rod with external hexagon Extended piston rod Smooth anodised aluminium piston rod
KP EL
With clamping unit With end-position locking
Q R3
Square piston rod High corrosion protection
R8
Dust protection (wiper seal)
TT
Low temperature
Software tools www.festo.com Configuration of Festo modular products www.festo.com
2012/01 Subject to change
Internet: www.festo.com/catalog/...
3
Standard cylinders DNC, ISO 15552Product range overview Function Design Type Piston Stroke Protection against rotation Through/hollow piston rod Extended male piston rod thread Special piston rod thread K5 Female piston rod thread K3
[mm] Double-act Basic version ing DNC 32, 40, 50, 63, 80, 100, 125
[mm] 25, 40, 50, 80, 10 2,000 100, 125, 160, 200, 250, 320, 400, 500
A
Position sensing Q
S2/S20
K2
Standard hole pattern, with clamping unit DNC-KP 32, 40, 50, 63, 80, 100, 125 DNCKE 40, 63, 100
10 2,000 S2
10 2,000
Standard hole pattern, with end-position locking DNC--EL 32, 40, 50, 63, 80, 100
10 2,000 S2
Standard hole pattern, cylinder/valve combination DNC-V1 V6 32, 40, 50, 63, 80, 100
100 2,000
Standard hole pattern, tandem cylinder DNCT 32, 40, 50 63, 80, 100, 125
2 500 3 500
4
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Product range overview Type High corrosion protection Smooth anodised piston rod -VCylinder/valve combination Page/Internet
Special spanner flats
Heat-resistant seals to max. 120 C
Extended piston rod
Slow speed (constant motion)
Low temperature TT
Dust protection
Low friction
K7 Basic version DNC
K8
K10
S6
S10
S11
R3
R8
V1 V6 9
Standard hole pattern, with clamping unit DNC-KP
23
DNCKE
dncke
Standard hole pattern, with end-position locking DNC--EL
31
Standard hole pattern, cylinder/valve combination DNC-V1 V6
38
Standard hole pattern, tandem cylinder DNCT
dnct
2012/01 Subject to change
Internet: www.festo.com/catalog/...
5
Standard cylinders DNC, ISO 15552Peripherals overview 1 2 3 4 6 9 aA bI bH bG aB 5 7 aJ aB aC 5 aD 8
aF aE aF bF aG aH aJ aI bJ bA bB 2 3 4 bD bE
5
DNC--S2 bC Mounting attachments and accessories Brief description 1 2 3 Multi-position kit DPNC Foot mounting HNC/CRHNC Flange mounting FNC/CRFNG Trunnion flange ZNCF/CRZNG Trunnion support LNZG/CRLNZG Swivel flange SNC Clevis foot LSNG Clevis foot LSNSG For connecting two cylinders with identical piston diameters to form a multi-position cylinder For bearing or end caps For bearing or end caps Cannot be used on the bearing cap in combination with bellows kit DADB For bearing or end caps Cannot be used on the bearing cap in combination with bellows kit DADB For end caps With spherical bearing Weld-on, with spherical bearing
DNC Basic version KP1)
EL
V1 V61)
Page/ Internet 47 48 49
4
50
5 6 7 8
52 53 56 56
1) 1) 1)
1) 1) 1)
1) 1) 1)
6
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Peripherals overview Mounting attachments and accessories Brief description 9 aJ aA aB aC aD aE aF aG aH aI Swivel flange SNCS Clevis foot LBG Swivel flange SNCL Swivel flange SNCB/SNCB--R3 Clevis foot LNG/CRLNG Clevis foot LSN Trunnion mounting kit ZNCM Rod eye SGS/CRSGS Right-angle clevis foot LQG Rod clevis SGA Coupling piece KSG Coupling piece KSZ Rod clevis SG/CRSG Self-aligning rod coupler FK Adapter AD Guide unit FENG Mounting kit SMB-8-FENG Slot cover ABP-5-S Proximity sensor SME/SMT-8 One-way flow control valve GRLA Push-in fitting QS Bellows kit DADB With spherical bearing for end caps For end caps For end caps With spherical bearing For mounting anywhere along the cylinder profile barrel With spherical bearing With male thread To compensate for radial deviations For cylinders with a non-rotating piston rod to compensate for radial deviations Permits a swivelling movement of the cylinder in one plane For compensating radial and angular deviations For fitting a suction cup on a hollow cylinder piston rod For protecting standard cylinders against rotation at high torque loads For attaching proximity sensor SMT-8 to cylinders in combination with guide unit FENG For protecting the sensor cables and keeping dirt out of the sensor slots Can be integrated in the cylinder profile barrel For regulating speed For connecting compressed air tubing with standard outside diameter Protects the cylinder (piston rod, seal and bearings) against a wide range of media and thus prevents premature wear The kit can only be used in combination with an extended piston rod (K8)
DNC Basic version KP1) 1) 1) 1) 1) 1) 1) 1) 1) 1) 1)
EL
V1 V61) 1) 1) 1) 1) 1)
Page/ Internet 55 56 55 54 56 56 51 57 56 57 57 57 57 57 57 62 62
bJ bA bB bC bD
2)
50 and above
63 63 64 quick star 58
bE bF bG bH bI
1) 2)
Not with variant S2 or S20 For piston 32, 40 mm only with variant R3
2012/01 Subject to change
Internet: www.festo.com/catalog/...
7
Standard cylinders DNC, ISO 15552Type codesu
DNC Type Double-acting DNC Piston [mm] Stroke [mm] Cushioning P PPV Position sensing A Without position sensing Via proximity sensor Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Standard cylinder
80
320
PPV
A
Note The standard cylinder DNC can be ordered using either a fixed part number and type designation or via the modular product system. The type code listed above only applies to the DNC standard cylinder with fixed part number and type designation. Variants can only be ordered using the modular product system.
8
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Technical data Function DNC- Without position sensing -N-TDiameter 32 125 mm Stroke length 10 2,000 mm
www.festo.com/en/ Spare_parts_service Wearing parts kits 22 DNC--A- With position sensing Standards-based cylinders to ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA 24 562, NF E 49 003.1 and UNI 10290)
DIN
General technical data Piston Pneumatic connection Piston rod thread K3 K5 Constructional design
32 Gx M10x1.25 M6 M10 Piston Piston rod Profile barrel 0.65
40 G M12x1.25 M8 M12
50 G M16x1.5 M10 M16
63 Gy M16x1.5 M10 M16
80 Gy M20x1.5 M12 M20
100 G M20x1.5 M12 M20
125 G M27x2 M16 M27
Max. torsional backlash of piston rod [] Cushioning Cushioning length PPV Position sensing Type of mounting Mounting position
Q
0.6
0.45
0.45
0.45
0.45
[mm]
Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 Via proximity sensor Via female thread Via accessories Any
22
32
32
42
Note: This product conforms to ISO 1179-1 and ISO 228-1
2012/01 Subject to change
Internet: www.festo.com/catalog/...
9
Standard cylinders DNC, ISO 15552Technical data Operating and environmental conditions Piston 32 Operating medium Operating pressure [bar]
40
50
63
80
100
125 0.6 10 1.5 10
R8 S11
TT Ambient temperature1) [C] Corrosion resistance class CRC2) Certification ATEX1) 2)
S6 TT R3
Filtered compressed air, lubricated or unlubricated 0.6 12 1.5 12 After 10 strokes 0.16 12 0.1 12 After 24 hours 0.3 12 0.2 12 1 12 20 +80 0 120 40 +80 2 3 Germanischer Lloyd Specified types www.festo.com
0.06 12 0.1 12
0.06 10 0.1 10
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
Force [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Max. impact energy at the end positions1)1)
32 483 415 415 415 0.1
40 754 633 633 633 0.2
50 1,178 990 990 990 0.2
63 1,870 1,682 1,682 1,682 0.5
80 3,016 2,721 2,721 2,721 0.9
100 4,712 4,418 4,418 4,418 1.2
125 7,363 6,881 6,881 6,881 5
S2/S20 S2/S20
The permissible impact energy is reduced by approx. 10% for variants K10 and S20
Permissible impact velocity:
vperm. =
2 x E perm. m dead + m load
vperm. Eperm. mIntrinsic mLoad
Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
Maximum permissible load:
m load =
2 x E perm. m dead v2
10
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Technical data Lateral force Fq as a function of stroke length l Basic version
Fq
32 40 50/63 80/100 125
2012/01 Subject to change
Internet: www.festo.com/catalog/...
11
Standard cylinders DNC, ISO 15552Technical data Lateral force Fq as a function of stroke length l and lever arm s Q Square piston rod 32 Max. torque = 800 Nmm / Max. stroke = 300 mm
40 Max. torque = 1,100 Nmm / Max. stroke = 400 mm
s [mm]
s [mm]
Fq [N]
Fq [N]
l [mm] 50/63 Max. torque = 1,500 Nmm / Max. stroke = 500 mm 80/100
l [mm]
Max. torque = 3,000 Nmm / Max. stroke = 600 mm
s [mm]
Fq [N]
s [mm] l [mm]
Fq [N]
l [mm]
Examples for piston 32 mm Example 1: Stroke length l = 150 mm Result: permissible Lateral force Fq = 9.5 N Lever arm s = 84 mm Example 2: Lateral force Fq = 40 N Result: permissible Stroke length l = 28 mm Lever arm s = 20 mm Example 3: Stroke length l = 150 mm Lever arm s = 20 mm Max. torque 800 Nmm Fq = Lever arm 100 mm =8N Result: permissible Fq = 8 N < Fqmax. = 9.5 N
Fq
12
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Technical data Weight [g] Piston Basic version Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke Q Square piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke S2 Through piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke K10 Smooth anodised piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke
32 517 30 162 9
40 800 45 307 16
50 1,260 64 538 25
63 1,709 73 663 25
80 2,790 106 1,131 38
100 4,653 115 1,544 38
125 6,771 168 2,809 63
504 29 149 8
738 41 244 11
1,187 60 465 20
1,632 68 587 20
2,652 99 994 31
4,508 108 1,399 31
576 39 170 18
895 61 330 32
1,390 89 560 50
1,917 98 711 50
3,114 144 1,200 76
5,297 153 1,660 76
7,529 231 2,925 126
443 24 88 3
655 35 162 6
1,001 47 279 8
1,437 57 391 9
2,302 81 643 13
4,138 90 1,029 13
5,719 127 1,757 22
S2-K10 Through, smooth anodised piston rod Product weight with 0 mm stroke 514 Additional weight per 10 mm stroke 27 Moving load with 0 mm stroke Additional load per 10 mm stroke TT Low temperature Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke 108 6
766 40 201 11
1,181 56 351 17
1,676 65 470 17
2,701 94 787 26
4,821 103 1,184 26
6,674 148 2,070 43
520 31 108 9
876 46 204 16
1,279 65 363 25
2,112 73 460 25
2,972 108 802 39
5,039 116 1,045 39
TT-S2 Low temperature with through piston rod Product weight with 0 mm stroke 606 Additional weight per 10 mm stroke 40 Moving load with 0 mm stroke Additional load per 10 mm stroke 169 18
1,020 62 326 32
1,546 89 573 49
2,401 98 687 49
3,453 147 1,199 77
5,617 154 1,473 77
2012/01 Subject to change
Internet: www.festo.com/catalog/...
13
Standard cylinders DNC, ISO 15552Technical data Materials Sectional view 3 2 1 2
Standard cylinder 1 2 3 Profile barrel Bearing and end caps Piston rod Seals
Basic version Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Polyurethane, nitrile rubber R8 S6
K10
R3
Wrought aluminium alloy, smooth anodised
Wrought aluminium alloy, anodised
High-alloy stainless steel
Standard cylinder 1 2 3 Profile barrel Bearing and end caps Piston rod Seals
S10
S11
TT Coated aluminium
Wrought aluminium alloy, smooth anodised Die-cast aluminium Tempered steel, High-alloy steel hard-chromium plated Polyurethane, nitrile Fluoro rubber rubber
Polyurethane
14
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Technical data Dimensions Basic version Download CAD Data www.festo.com/us/cad
1 Socket head screw with female thread for mounting attachments [mm] 32 40 50 63 80 100 125 [mm] 32 40 50 63 80 100 125 3.3 3.6 5.1 6.6 10.5 8 14 12 16 20 20 25 25 32 22 24 32 32 40 40 54 L7 AM B d11 30 35 40 45 45 55 60 MM
2 Regulating screw for adjustable end-position cushioning
3 Slot for proximity sensor SME/SMT-8
+
= plus stroke length
BG
E
EE
J2 TT
J3
KK
L1
L2
16 16 17 17 17 17 22 PL RT
45 54 64 75 93 110 134 TG
Gx G G Gy Gy G G VA
6 8 10.4 12.4 12.5 12 13 VD WH 11
5.2 6 8.5 10 8 10 8 ZJ
M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 M27x2 1
18 21.5 28 28.5 34.7 38.2 46 2
94 105 106 121 128 138 160 3
15.6 14 14 17 16.4 18.8 18
M6 M6 M8 M8 M10 M10 M12
32.5 38 46.5 56.5 72 89 110
4 4 4 4 4 4 6
10 10.5 11.5 15 15.7 19.2 20.5
26 30 37 37 46 51 65
120 135 143 158 174 189 225
10 13 17 17 22 22 27
16 18 24 24 30 30 36
6 6 8 8 6 6 8
Note: This product conforms to ISO 1179-1 and ISO 228-1
2012/01 Subject to change
Internet: www.festo.com/catalog/...
15
Standard cylinders DNC, ISO 15552Technical data Dimensions Variants Q Square piston rod Download CAD Data www.festo.com/us/cad
S2 Through piston rod
+ = plus stroke length ++ = plus 2x stroke length S20 Through hollow piston rod
+ = plus stroke length ++ = plus 2x stroke length [mm] 32 40 50 63 80 100 1251) 2)
B1
D8 TT 4.5 5.5 81) 8 11.7 11.7 13 4.5 6 8 8 11.72) 11.72)
ZJ
ZM TT
10 12 16 16 20 20
120 135 143 158 174 189 225
148 167 183 199 222 240 291
146.6 165.3 180.3 195.9 221.1 239.7
Internal narrowing to 5.5 mm Internal narrowing to 10.2 mm
16
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Technical data Dimensions Variants K2 Extended male piston rod thread Download CAD Data K3 Female piston rod thread www.festo.com/us/cad
K5 Special piston rod thread
K7 Piston rod with external hexagon
K8 Extended piston rod Note In combination with variant S2/S20, the piston rod is extended at one end. In combination with variant Q, the square piston rod is extended.
[mm] 32 40 50 63 80 100 1251)
A1 max. 35 35 70 70 70 70 70
A2 max. 500 500 500 500 500 500 500
AF
AM
KF Basic thread
KK Special thread1) M10 M12 M16 M16 M20 M20 M27
T4
WH
1
12 12 16 16 20 20 32
22 24 32 32 40 40 54
M6 M8 M10 M10 M12 M12 M16
M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 M27x2
2.6 3.3 4.7 4.7 6.1 6.1 8
26 30 37 37 46 51 65
10 13 17 17 22 22 27
The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
2012/01 Subject to change
Internet: www.festo.com/catalog/...
17
Standard cylinders DNC, ISO 15552Technical data Ordering data Type
Piston [mm] 32
Stroke [mm] 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500
Without position sensing Part No. Type1) 163 319 163 320 163 321 163 322 163 323 163 324 163 325 163 326 163 327 163 328 163 329 163 330 163 351 163 352 163 353 163 354 163 355 163 356 163 357 163 358 163 359 163 360 163 361 163 362 163 383 163 384 163 385 163 386 163 387 163 388 163 389 163 390 163 391 163 392 163 393 163 394 163 415 163 416 163 417 163 418 163 419 163 420 163 421 163 422 163 423 163 424 163 425 163 426 DNC-32-25-PPV DNC-32-40-PPV DNC-32-50-PPV DNC-32-80-PPV DNC-32-100-PPV DNC-32-125-PPV DNC-32-160-PPV DNC-32-200-PPV DNC-32-250-PPV DNC-32-320-PPV DNC-32-400-PPV DNC-32-500-PPV DNC-40-25-PPV DNC-40-40-PPV DNC-40-50-PPV DNC-40-80-PPV DNC-40-100-PPV DNC-40-125-PPV DNC-40-160-PPV DNC-40-200-PPV DNC-40-250-PPV DNC-40-320-PPV DNC-40-400-PPV DNC-40-500-PPV DNC-50-25-PPV DNC-50-40-PPV DNC-50-50-PPV DNC-50-80-PPV DNC-50-100-PPV DNC-50-125-PPV DNC-50-160-PPV DNC-50-200-PPV DNC-50-250-PPV DNC-50-320-PPV DNC-50-400-PPV DNC-50-500-PPV DNC-63-25-PPV DNC-63-40-PPV DNC-63-50-PPV DNC-63-80-PPV DNC-63-100-PPV DNC-63-125-PPV DNC-63-160-PPV DNC-63-200-PPV DNC-63-250-PPV DNC-63-320-PPV DNC-63-400-PPV DNC-63-500-PPV
With position sensing Part No. Type1) 163 305 163 306 163 307 163 308 163 309 163 310 163 311 163 312 163 313 163 314 163 315 163 316 163 337 163 338 163 339 163 340 163 341 163 342 163 343 163 344 163 345 163 346 163 347 163 348 163 369 163 370 163 371 163 372 163 373 163 374 163 375 163 376 163 377 163 378 163 379 163 380 163 401 163 402 163 403 163 404 163 405 163 406 163 407 163 408 163 409 163 410 163 411 163 412 DNC-32-25-PPV-A DNC-32-40-PPV-A DNC-32-50-PPV-A DNC-32-80-PPV-A DNC-32-100-PPV-A DNC-32-125-PPV-A DNC-32-160-PPV-A DNC-32-200-PPV-A DNC-32-250-PPV-A DNC-32-320-PPV-A DNC-32-400-PPV-A DNC-32-500-PPV-A DNC-40-25-PPV-A DNC-40-40-PPV-A DNC-40-50-PPV-A DNC-40-80-PPV-A DNC-40-100-PPV-A DNC-40-125-PPV-A DNC-40-160-PPV-A DNC-40-200-PPV-A DNC-40-250-PPV-A DNC-40-320-PPV-A DNC-40-400-PPV-A DNC-40-500-PPV-A DNC-50-25-PPV-A DNC-50-40-PPV-A DNC-50-50-PPV-A DNC-50-80-PPV-A DNC-50-100-PPV-A DNC-50-125-PPV-A DNC-50-160-PPV-A DNC-50-200-PPV-A DNC-50-250-PPV-A DNC-50-320-PPV-A DNC-50-400-PPV-A DNC-50-500-PPV-A DNC-63-25-PPV-A DNC-63-40-PPV-A DNC-63-50-PPV-A DNC-63-80-PPV-A DNC-63-100-PPV-A DNC-63-125-PPV-A DNC-63-160-PPV-A DNC-63-200-PPV-A DNC-63-250-PPV-A DNC-63-320-PPV-A DNC-63-400-PPV-A DNC-63-500-PPV-A
40
50
63
1)
The mounting nut on the piston rod thread is included in the scope of delivery
18
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Technical data Ordering data Type
Piston [mm] 80
Stroke [mm] 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500
Without position sensing Part No. Type1) 163 447 163 448 163 449 163 450 163 451 163 452 163 453 163 454 163 455 163 456 163 457 163 458 163 479 163 480 163 481 163 482 163 483 163 484 163 485 163 486 163 487 163 488 163 489 163 490 163 511 163 512 163 513 163 514 163 515 163 516 163 517 163 518 163 519 163 520 163 521 163 522 DNC-80-25-PPV DNC-80-40-PPV DNC-80-50-PPV DNC-80-80-PPV DNC-80-100-PPV DNC-80-125-PPV DNC-80-160-PPV DNC-80-200-PPV DNC-80-250-PPV DNC-80-320-PPV DNC-80-400-PPV DNC-80-500-PPV DNC-100-25-PPV DNC-100-40-PPV DNC-100-50-PPV DNC-100-80-PPV DNC-100-100-PPV DNC-100-125-PPV DNC-100-160-PPV DNC-100-200-PPV DNC-100-250-PPV DNC-100-320-PPV DNC-100-400-PPV DNC-100-500-PPV DNC-125-25-PPV DNC-125-40-PPV DNC-125-50-PPV DNC-125-80-PPV DNC-125-100-PPV DNC-125-125-PPV DNC-125-160-PPV DNC-125-200-PPV DNC-125-250-PPV DNC-125-320-PPV DNC-125-400-PPV DNC-125-500-PPV
With position sensing Part No. Type1) 163 433 163 434 163 435 163 436 163 437 163 438 163 439 163 440 163 441 163 442 163 443 163 444 163 465 163 466 163 467 163 468 163 469 163 470 163 471 163 472 163 473 163 474 163 475 163 476 163 497 163 498 163 499 163 500 163 501 163 502 163 503 163 504 163 505 163 506 163 507 163 508 DNC-80-25-PPV-A DNC-80-40-PPV-A DNC-80-50-PPV-A DNC-80-80-PPV-A DNC-80-100-PPV-A DNC-80-125-PPV-A DNC-80-160-PPV-A DNC-80-200-PPV-A DNC-80-250-PPV-A DNC-80-320-PPV-A DNC-80-400-PPV-A DNC-80-500-PPV-A DNC-100-25-PPV-A DNC-100-40-PPV-A DNC-100-50-PPV-A DNC-100-80-PPV-A DNC-100-100-PPV-A DNC-100-125-PPV-A DNC-100-160-PPV-A DNC-100-200-PPV-A DNC-100-250-PPV-A DNC-100-320-PPV-A DNC-100-400-PPV-A DNC-100-500-PPV-A DNC-125-25-PPV-A DNC-125-40-PPV-A DNC-125-50-PPV-A DNC-125-80-PPV-A DNC-125-100-PPV-A DNC-125-125-PPV-A DNC-125-160-PPV-A DNC-125-200-PPV-A DNC-125-250-PPV-A DNC-125-320-PPV-A DNC-125-400-PPV-A DNC-125-500-PPV-A
100
125
Ordering data Variable stroke Type Piston [mm] 32 40 50 63 80 100 1251)
Stroke [mm] 10 2 000 10 2 000 10 2 000 10 2 000 10 2 000 10 2 000 10 2 000
Without position sensing Part No. Type1) 163 318 163 350 163 382 163 414 163 446 163 478 163 510 DNC-32--PPV DNC-40--PPV DNC-50--PPV DNC-63--PPV DNC-80--PPV DNC-100--PPV DNC-125--PPV
With position sensing Part No. Type1) 163 304 163 336 163 368 163 400 163 432 163 464 163 496 DNC-32--PPV-A DNC-40--PPV-A DNC-50--PPV-A DNC-63--PPV-A DNC-80--PPV-A DNC-100--PPV-A DNC-125--PPV-A
The mounting nut on the piston rod thread is included in the scope of delivery
2012/01 Subject to change
Internet: www.festo.com/catalog/...
19
Standard cylinders DNC, ISO 15552Ordering data Modular products 0 Mandatory data M Module No. Function Stroke 0 Options O Position sensing Type of piston rod Female thread
Piston
Cushioning
Protection against rotation P PPV A Q
Extended male thread S2 S20 K2
Special thread
163 302 163 334 163 366 163 398 163 430 163 462 163 494 Order example 163 430 Ordering table Size 0 Module No. M Function Piston Stroke Cushioning
DNC
32 40 50 63 80 100 125
10 2,000
K3
K5
DNC
80
550
PPV
A
Q
S2
K3
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
100 163 462 100
125 163 494 125
Condition Code s
Enter code
Standard cylinder, double-acting, based on ISO 15552 [mm] 32 40 50 63 80 [mm] 10 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Square piston rod Through piston rod Through, hollow piston rod Piston rod with extended male thread [mm] 1 35 1 70 Piston rod with female thread (M6) (M8) (M10) (M10) Piston rod with special thread M10 M12 M16 M16x24
aE 2 3 4 5
DNC - - -P -PPV -A -Q -S2 -S20 -K2 -K3 -K5
DNC
0 Position sensing O Protection against rotation Type of piston rod Extended male thread Female thread Special thread
(M12) M20
(M12) M20
(M16) M27
6 7
aE 2
PPV For piston 125 not with S11 Q Max. stroke: 10 1,500 mm. In combination with S2: square piston rod at bearing cap end only. Not with S20, K7, K10, S10, S11, R8
S20 Max. stroke: 850 mm. In combination with K8: piston rod extended at both ends. Not with K2, K3, K5, K10, S6, S10, S11, R8
5 6 7
K2 K3 K5
Not with K3, K10 With K5: on request. Not with K7 Not with K10
3
S2
In combination with K2: thread extended at both ends. In combination with K3: female thread at both ends. In combination with K5: special thread at both ends. In combination with K8: piston rod extended at bearing cap end only. Not with S20, K7, S10, S11
Transfer order code DNC
20
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Ordering data Modular products 0 Options O Special spanner flats Improved running performance Temperature resistance Low temperature Running characteristics Wiper seal
Extended piston rod
Slow speed (constant motion) TT S10
Corrosion protection
K7
K8
K10
S6
S11
R3
R8
Ordering table Size
100K8
32
40
50
63
80
100
125
Condition Code s 8 -K7 -K8 -K10 -S6 -TT -S10 -S11 -R3 -R8
Enter code
Special spanner flats 0 Extended piston rod O
Piston rod with external hexagon Extended piston rod [mm] 1 500 Improved running performance Smooth anodised aluminium coated piston rod Temperature resistance Heat-resistant seals for temperatures up to 120 C Low temperature [C] 40 +80 Slow speed (constant motion) Slow speed (constant motion at low piston speeds) Running characteristics Low friction Corrosion protection High corrosion protection Wiper seal Dust protectionNot with Q, S2, K10 Max. stroke: 1,000 mm. Not with S6, R3, R8 aC S11 aD CT, R3 Not with S10, S11, R8 Not with P, Q, K7, K10, S6, S10, S11, R8 aB S10
9 aJ aA aB aC aD
8 K7 9 K10 aJ S6 aA TT
Max. stroke: 500 mm; additional strokes on request. Not with S11, R3, R8 Max. stroke: 500 mm; additional strokes on request. Not with R3, R8 Not with R8
Transfer order code
2012/01 Subject to change
Internet: www.festo.com/catalog/...
21
Standard cylinders DNC, ISO 15552Ordering data Wearing parts kits Part No. Piston 32 40 50 63 80 100 125 Type Part No. Type Basic version 369 195 DNC-32--PPV-(A) 369 196 DNC-40--PPV-(A) 369 197 DNC-50--PPV-(A) 369 198 DNC-63--PPV-(A) 369 199 DNC-80--PPV-(A) 369 200 DNC-100--PPV-(A) 369 201 DNC-125--PPV-(A) S6 Heat-resistant seals up to max. 120 C 384 214 DNC-32--PPV-(A)-S6 384 215 DNC-40--PPV-(A)-S6 384 216 DNC-50--PPV-(A)-S6 384 217 DNC-63--PPV-(A)-S6 384 218 DNC-80--PPV-(A)-S6 384 219 DNC-100--PPV-(A)-S6 384 220 DNC-125--PPV-(A)-S6
22
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-KP, standard hole pattern, with clamping unitTechnical data Function DNC--KP Without position sensing -N-TDiameter 32 125 mm Stroke length 10 2,000 mm
www.festo.com/en/ Spare_parts_service Wearing parts kits 30 DNC--A--KP With position sensing Note
Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without
additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems.
General technical data Piston Pneumatic connection Piston rod thread K3 K5 [mm] Cylinder KP
32 Gx M5 M10x1.25 M6 M10 0.5
40 G Gx M12x1.25 M8 M12
50 G Gx M16x1.5 M10 M16 0.7
63 Gy Gx M16x1.5 M10 M16
80 Gy Gx M20x1.5 M12 M20
100 G Gx M20x1.5 M12 M20
125 G Gx M27x2 M16 M27 1
Max. axial backlash with clamped piston rod without load Constructional design
Cushioning Cushioning length PPV Position sensing Type of mounting [mm]
Mounting position Clamping type with effective direction
Piston Piston rod Profile barrel Clamping unit Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 Via proximity sensor Via female thread Via accessories Any At both ends
22
32
32
42
Note: This product conforms to ISO 1179-1 and ISO 228-1
Operating and environmental conditions Operating medium Operating pressure [bar] Min. release pressure [bar] Ambient temperature1) [C] Corrosion resistance class CRC2) Certification1) 2)
Filtered compressed air, lubricated or unlubricated 1.5 10 3 10 +80 2 Germanischer Lloyd
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
23
Standard cylinders DNC-KP, standard hole pattern, with clamping unitTechnical data Impact energy [J] Piston
32
40 0.2 2 x E perm. m dead + m load
50 0.2 vperm. Eperm. mIntrinsic mLoad
63 0.5
80 0.9
100 1.2 Note
125 5
Max. impact energy at the end positions 0.1
Permissible impact velocity:
vperm. =
Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
Maximum permissible load: Forces [N] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Static holding force Note The specified holding force refers to a static load. If this value is exceeded, slippage may occur. Dynamic forces occurring during operation must not S2 S2
m load =
2 x E perm. m dead v2
This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
32 483 415 415 415 600
40 754 633 633 633 1,000
50 1,178 990 990 990 1,400
63 1,870 1,682 1,682 1,682 2,000
80 3,016 2,721 2,721 2,721 5,000
100 4,712 4,418 4,418 4,418 5,000
125 7,363 6,881 6,881 6,881 7,500
exceed the static holding force. The clamping unit is not backlash-free in the clamped condition if varying loads are applied to the piston rod.
Activation: The clamping unit may only be released if the forces at the piston have reached equilibrium. Otherwise, there is a risk of accidents due to
sudden movement of the piston rod. Blocking off the air supply at both ends (e.g. with a 5/3-way valve) does not provide any safety.
24
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-KP, standard hole pattern, with clamping unitTechnical data Max. lateral force Fq as a function of stroke length l
Fq
32 40 50/63 80/100 125
Materials Sectional view 2 4 7 5 6 3 1 2
Standard cylinder 1 2 3 4 5 6 7 Profile barrel Bearing and end caps Piston rod Housing, clamping unit Clamping jaws Spring Piston Seals Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Wrought aluminium alloy, anodised Brass Spring steel Polyacetal Polyurethane, nitrile rubber
2012/01 Subject to change
Internet: www.festo.com/catalog/...
25
Standard cylinders DNC-KP, standard hole pattern, with clamping unitTechnical data Dimensions Basic version Download CAD Data www.festo.com/us/cad
1 Socket head screw with female thread for mounting attachments [mm] 32 40 50 63 80 100 125 [mm] 32 40 50 63 80 100 125 14 16 20 24 31.5 31 42 3.3 3.6 5.1 6.6 10.5 8 14 12 16 20 20 25 25 32 22 24 32 32 40 40 54 L5 AM B d11 30 35 40 45 45 55 60 L7 BG
2 Regulating screw for adjustable end-position cushioning
3 Slot for proximity sensor SME/SMT-8
+
= plus stroke length
D1 f9 20 24 30 38 48 48 65 PL
D2
E
EE
H1
J2
J3
KK
L2
L3
16 16 17 17 17 17 22 MM
M5 Gx Gx Gx Gx Gx Gx RT
45 54 64 75 93 110 134 TG
Gx G G Gy Gy G G VA
67 88 107 123 165.5 174 207 VD
6 8 10.4 12.4 12.5 12 13 WH
5.2 6 8.5 10 8 10 8 ZJ
M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 M27x2 1
94 105 106 121 128 138 160 2
45 53 67 76 95 98 125 3
15.6 14 14 17 16.4 18.8 18
M6 M6 M8 M8 M10 M10 M12
32.5 38 46.5 56.5 72 89 110
4 4 4 4 4 4 6
11.5 11.5 11 11 12.5 12 27.5
26 30 37 37 46 51 65
165 188 210 234 269 287 350
10 13 17 17 22 22 27
16 18 24 24 30 30 36
6 6 8 8 6 6 8
Note: This product conforms to ISO 1179-1 and ISO 228-1
Note The dimensions for the cylinder/valve combination are on page 42
26
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-KP, standard hole pattern, with clamping unitTechnical data Dimensions Variants Q Square piston rod Note Clamping unit and variant Q only in combination with S2. Download CAD Data www.festo.com/us/cad
S2 Through piston rod
+ = plus stroke length ++ = plus 2x stroke length Note The thread types at both piston rod ends are identical. K2 Extended male piston rod thread In combination with variant Q, the left-hand piston rod is round, the right-hand piston rod square. The clamping unit is mounted on K3 Female piston rod thread the left-hand, round piston rod.
K5 Special piston rod thread
K7 Piston rod with external hexagon
K8 Extended piston rod Note In combination with variant S2, the piston rod is extended at one end. The clamping unit is mounted on the side of the piston rod that is not extended. If variant Q is also required, the extension will only be added to the square piston rod.
[mm] 32 40 50 63 80 100 1251)
A1 max. 35 35 70 70 70 70 70
A2 max. 500 500 500 500 500 500 500
AF
AM
B1
KF Basic thread
KK Special thread1) M10 M12 M16 M16 M20 M20 M27
T4
WH
ZJ
ZM
1
12 12 16 16 20 20 32
22 24 32 32 40 40 54
10 12 16 16 20 20
M6 M8 M10 M10 M12 M12 M16
M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 M27x2
2.6 3.3 4.7 4.7 6.1 6.1 8
26 30 37 37 46 51 65
165 188 210 234 269 287 350
193 220 250 275 317 338 416
10 13 17 17 22 22 27
The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
2012/01 Subject to change
Internet: www.festo.com/catalog/...
27
Standard cylinders DNC-KP, standard hole pattern, with clamping unitOrdering data Modular products 0 Mandatory data M Module No. Function Piston Stroke Cushioning 0 Options O Position sensing Protection against rotation Q Type of piston rod
163 302 163 334 163 366 163 398 163 430 163 462 163 494 Order example 163 430 Ordering table Size 0 Module No. M Function Piston Stroke Cushioning
DNC
32 40 50 63 80 100 125
10 2,000
P PPV
A
S2
DNC
80
550
PPV
A
Q
S2
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
100 163 462
125 163 494
Condition Code s
Enter code
Standard cylinder, double-acting, standard hole pattern, with clamping unit [mm] 32 40 50 63 80 100 125 [mm] 10 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Square piston rod Through piston rod2 S2
DNC - - -P -PPV 1 2 -A -Q -S2
DNC
0 Position sensing O Protection against rotation Type of piston rod1 Q Max. stroke: 10 1,500 mm
In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends In combination with K8: piston rod extended at bearing cap end only In combination with KP: clamping unit at end cap Not with K7
In combination with S2: square piston rod at bearing cap end only In combination with KP: only supplied with S2 Not with K7
Transfer order code DNC
28
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-KP, standard hole pattern, with clamping unitOrdering data Modular products 0 Options O Extended male thread Female thread Special thread Special spanner flats Extended piston rod 0 M Clamping unit 0 O Cylinder/valve combination
K2
K3
K5
K7
K8
KP
V1 V2 V3 V4 V5 V6
Ordering table Size
K3
100K8
KP
32
40
50
63
80
100
125
Condition Code s 3 -K2 -K3 -K5 -K7 -K8 -KP -V1 -V2 -V3 -V4 -V5 -V6
Enter code
Piston rod with extended male thread [mm] 1 35 1 70 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) (M12) (M12) Special thread Piston rod with special thread M10 M12 M16 M16 M20 M20 Special spanner flats Piston rod with external hexagon Extended piston rod Extended piston rod [mm] 1 500 0 Clamping unit M Attached 0 Cylinder/valve combination O Single solenoid valve, fitted on right, piston rod retracted when unactuated Single solenoid valve, fitted on right, piston rod advanced when unactuated Double solenoid valve, fitted on right Single solenoid valve, fitted on left, piston rod retracted when unactuated Single solenoid valve, fitted on left, piston rod advanced when unactuated Double solenoid valve, fitted on left 0 O3 4 K2 K3 Not with K3 With K5: on request Not with K7 5 6 KP V
Extended male thread
(M16) M27
4
5 6 6 6 6 6 6
-KP
Without S2: position of the clamping unit at the bearing cap Min. stroke: 100 mm
Transfer order code KP
2012/01 Subject to change
Internet: www.festo.com/catalog/...
29
Standard cylinders DNC-KP, standard hole pattern, with clamping unitOrdering data Wearing parts kits Part No. Piston 32 40 50 63 80 100 125 Type Basic version 369 195 DNC-32--PPV-(A) 369 196 DNC-40--PPV-(A) 369 197 DNC-50--PPV-(A) 369 198 DNC-63--PPV-(A) 369 199 DNC-80--PPV-(A) 369 200 DNC-100--PPV-(A) 369 201 DNC-125--PPV-(A)
30
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingTechnical data Function DNC--A--EL With position sensing www.festo.com/en/ Spare_parts_service Wearing parts kits 22
-N-T-
Diameter 32 100 mm Stroke length 10 2,000 mm
Note Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems.
General technical data Piston Pneumatic connection Piston rod thread Max. axial backlash with end position locked Constructional design Cylinder EL [mm]
32 Gx M3 M10x1.25 1.3
40 G M12x1.25
50 G M5 M16x1.5
63 Gy M16x1.5
80 Gy M20x1.5 2.1
100 G M20x1.5
End-position locking
ELB ELV ELH
Cushioning Cushioning length PPV [mm] Position sensing Type of mounting Mounting position
EL
Piston Piston rod Profile barrel At both ends At front At rear Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 8.2 8.3 7.3 Via proximity sensor Via female thread Via accessories Any
22 10.8
32 9.8
32 11.8
Note: This product conforms to ISO 1179-1 and ISO 228-1
Note End-position locking should only be operated in conjunction with double-acting cylinders with exhaust air flow control in order to ensure that the lock is always completely released prior to starting the drive movement. No screws with a head or similar may be used in place of end-position locking, as there is a risk that the function will be impaired if they are screwed in too deeply. The exhaust hole must not be closed. Locking can be performed from any stroke position once the drive is brought mechanically into its end position. End-position locking has been designed to prevent the load dropping in case of pressure failure. An excessive end-position cushioning setting (more than 50% closed) can result in the locking bolt not engaging reliably, resulting in premature wear.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
31
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingTechnical data Operating and environmental conditions Piston 32 Operating medium Operating pressure [bar] Ambient temperature1) [C] Corrosion resistance class CRC2) Certification1) 2)
40
50
63
80
100
Filtered compressed air, lubricated or unlubricated 2.5 12 1.5 12 20 +80 2 Germanischer Lloyd
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Impact energy [J] Piston
32
40 0.2 2 x E perm. m dead + m load
50 0.2 vperm. Eperm. mIntrinsic mLoad
63 0.5 Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
80 0.9 Note
100 1.2
Max. impact energy at the end positions 0.1
Permissible impact velocity:
vperm. =
Maximum permissible load: Forces [N] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Static holding force Sizing example Note When sizing pneumatic cylinders it is recommended as a basic principle that only 50% of the indicated theoretical forces (see above) be used.
m load =
2 x E perm. m dead v2
This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
32 483 415 500
40 754 633
50 1,178 990 2,000
63 1,870 1,682
80 3,016 2,721 5,000
100 4,712 4,418
Given: Installation position = Vertical Workpiece load = 44 kg F = m x g = 44 kg x 9.81 m/s2 = 431.6 N To be calculated: Suitable piston
Example with 32 mm piston : Theoretical force at 6 bar, advancing = 483 N 50% of the theoretical force = 241.5 N Static holding force with 32 mm piston = 500 N The static holding force of end-position locking is within the permissible range (max. 500 N) with a workpiece load of 44 kg (431.6 N), however the cylinder would be at 89% capacity. Result: A cylinder with a piston of 40 mm is therefore recommended for this application.
32
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingTechnical data Max. lateral force Fq as a function of stroke length l
Fq
Weight [g] Piston Basic version Product weight with 0 mm stroke Additional weight per 10 mm stroke S2 Through piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Materials Sectional view 2 1 3 2
32 40 50/63 80/100
32 537 30
40 820 45
50 1,320 64
63 1,769 73
80 2,970 106
100 4,833 115
596 39
915 61
1,450 89
1,977 98
3,294 144
5,477 153
Standard cylinder 1 2 3 Profile barrel Bearing and end caps Piston rod Seals Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Polyurethane, nitrile rubber
2012/01 Subject to change
Internet: www.festo.com/catalog/...
33
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingTechnical data Dimensions Basic version Download CAD Data www.festo.com/us/cad
1 Socket head screw with female thread for mounting attachments Dimensions Variants S2 Through piston rod
2 Regulating screw for adjustable end-position cushioning
3 Slot for proximity sensor
+
= plus stroke length
Download CAD Data
www.festo.com/us/cad
+ = plus stroke length ++ = plus 2x stroke length [mm] 32 40 50 63 80 100 [mm] 32 40 50 63 80 100 94 105 106 121 128 138 13.8 16.6 17.1 16.6 19.9 22.8 12 16.6 17.1 16.6 19.9 22.8 3.3 3.6 5.1 6.6 10.5 8 12 16 20 20 25 25 15.6 14 14 17 16.4 18.8 M6 M6 M8 M8 M10 M10 32.5 38 46.5 56.5 72 89 4 4 4 4 4 4 10 10.5 11.5 15 15.7 19.2 22 24 32 32 40 40 L2 AM B d11 30 35 40 45 45 55 L3 BG D1 f8 13 13 20 20 20 20 L7 D2 E EE G H1 H2 J1 J2 J3 KK L1
1
16 16 17 17 17 17 L4
M3 M3 M5 M5 M5 M5 MM
45 54 64 75 93 110 PL
Gx G G Gy Gy G RT
25.1 29.6 29.6 35.6 35.9 38.8 TG
57.5 64 78.5 84.5 104.5 113.5 VA
70 74 93 93 116 116 VD
22.5 27 32 37.5 46.5 55 WH 2 26 30 37 37 46 51
6 8 10.4 12.4 12.5 12 ZM
5.2 6 8.5 10 8 10 ZJ
M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 1 2
18 21.5 28 28.5 34.7 38.2 3
148 167 183 199 222 240
120 135 143 158 174 189
10 13 17 17 22 22
16 18 24 24 30 30
6 6 8 8 6 6
Note: This product conforms to ISO 1179-1 and ISO 228-1
34
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingTechnical data Dimensions Variants K2 Extended male piston rod thread Download CAD Data www.festo.com/us/cad
K3 Female piston rod thread
K5 Special piston rod thread
K8 Extended piston rod Note In combination with variant S2, the piston rod is extended at one end.
[mm] 32 40 50 63 80 1001)
A1 max. 35 35 70 70 70 70
A2 max. 500 500 500 500 500 500
AF
AM
KF Basic thread
KK Special thread1) M10 M12 M16 M16 M20 M20
T4
WH
1
12 12 16 16 20 20
22 24 32 32 40 40
M6 M8 M10 M10 M12 M12
M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5
2.6 3.3 4.7 4.7 6.1 6.1
26 30 37 37 46 51
10 13 17 17 22 22
The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
2012/01 Subject to change
Internet: www.festo.com/catalog/...
35
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingOrdering data Modular products 0 Mandatory data M Module No. 163 302 163 334 163 366 163 398 163 430 163 462 Order example 163 430 Ordering table Size 0 Module No. M Function Piston Stroke Cushioning 0 Position sensing O Type of piston rod1 S2
0 Options O Piston 32 40 50 63 80 100 Stroke 10 2,000 Cushioning P PPV Position sensing A Type of piston rod S2
Function DNC
DNC
80
550
PPV
A
S2
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
100 163 462
Condition Code s
Enter code
Standard cylinder, double-acting, standard hole pattern, with end-position locking [mm] 32 40 50 63 80 100 [mm] 10 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Through piston rod 1
DNC - - -P -PPV -A -S2
DNC
In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends
Transfer order code DNC
36
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-EL, standard hole pattern, with end-position lockingOrdering data Modular products 0 Options O Extended male thread K2 Female thread K3 Special thread K5 Extended piston rod K8 0 M End-position locking ELB ELV ELH
Ordering table Size Extended male thread 0 O Female thread Special thread Extended piston rod 0 End-position locking M
K3
100K8
32
40
50
63
80
100
Condition Code s 2 -K2 -K3 -K5 -K8 4 4 4 -ELB -ELV -ELH
Enter code
Piston rod with extended male thread [mm] 1 35 1 70 Piston rod with female thread (M6) (M8) (M10) Piston rod with special thread M10 M12 M16 Extended piston rod [mm] 1 500 At both ends At front At rear
(M10) M16
(M12) M20
(M12) M20
3
2 K2 3 K3
Not with K3 With K5: on request In combination with K8 and S2: on request only
4 ELB, ELV, ELH
Transfer order code
2012/01 Subject to change
Internet: www.festo.com/catalog/...
37
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationTechnical data Function DNC- Without position sensing -N-TDiameter 32 100 mm Stroke length 100 2,000 mm
www.festo.com/en/ Spare_parts_service Wearing parts kits 30
DNC--A- With position sensing
Valve variants Single solenoid valve unactuated, piston rod retracted
Double solenoid valve unactuated, piston rod retracted
DNC--V1 fitted on right
DNC--V3 fitted on right
DNC--V4 fitted on left
DNC--V6 fitted on left
Single solenoid valve unactuated, piston rod advanced Note As viewed from the front of the cylinder (piston rod end) with valve fitted on left or right. DNC--V2 fitted on right In this example, the valve is fitted on the right.
DNC--V5 fitted on left
38
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationTechnical data General technical data Piston Cylinder Pneumatic connection Piston rod thread K3 K5 Constructional design
32
40
50
63 Gy M16x1.5 M10 M16
80 Gy M20x1.5 M12 M20
100 G M20x1.5 M12 M20
Cushioning Cushioning length PPV Position sensing Type of mounting Mounting position Valve Valve used [mm]
Gx G G M10x1.25 M12x1.25 M16x1.5 M6 M8 M10 M10 M12 M16 Piston Piston rod Profile barrel Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 Via proximity sensor Via female thread Via accessories Any
22
32
32
single solenoid double solenoid
CPE14-M1BH-5L-x CPE14-M1BH-5J-x Gx Piston spool valve Via mounting kit 24 +10/15% 1 100% IP65
CPE18-M1H-5L- CPE18-M1H-5J- G
Ordering data Valves and accessories CPE24-M1H-5L-y CPE24-M1H-5J-y Gy
46
Pneumatic connection Constructional design Type of mounting Operating voltage [V DC] Power consumption [W] Duty cycle Protection class with plug socketNote: This product conforms to ISO 1179-1 and ISO 228-1
1.5
Operating and environmental conditions Piston 32 Operating medium Operating pressure [bar] Ambient temperature1) [C] Corrosion resistance class CRC2) Certification1) 2)
40
50
63
80
100
Filtered compressed air, lubricated or unlubricated 38 2.5 10 0 +50 2 Germanischer Lloyd
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
39
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationTechnical data Force [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Max. impact energy at the end positions1)1)
32 483 415 415 415 0.1
40 754 633 633 633 0.2
50 1,178 990 990 990 0.2
63 1,870 1,682 1,682 1,682 0.5
80 3,016 2,721 2,721 2,721 0.9
100 4,712 4,418 4,418 4,418 1.2
S2/S20 S2/S20
The permissible impact energy is reduced by approx. 10% for variants K10 and S20
Permissible impact velocity:
vperm. =
2 x E perm. m dead + m load
vperm. Eperm. mIntrinsic mLoad
Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
Maximum permissible load:
m load =
2 x E perm. m dead v2
Max. lateral force Fq as a function of stroke length l
Fq
32 40 50/63 80/100
40
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationTechnical data Materials Sectional view 2 1 2
3 Standard cylinder 1 2 3 4 Profile barrel Bearing and end caps Piston rod Seals, cylinder Housing, valve Seals, valve Basic version R8 S10
4 S11 K10
Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Tempered steel Polyurethane, nitrile rubber Die-cast aluminium, polyamide, steel Nitrile rubber
High-alloy steel Fluoro rubber
Wrought aluminium alloy, anodised Polyurethane, nitrile rubber
2012/01 Subject to change
Internet: www.festo.com/catalog/...
41
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationTechnical data Dimensions Download CAD Data www.festo.com/us/cad
1 Plug socket not included in scope of delivery
+ = plus half stroke length
42
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationTechnical data [mm] 32 40 50 63 80 100 Note Additional dimensions relating to the basic version and its variants are provided on page 15, with clamping unit on page 26. 62 71 85 96 123 140 59 68 82 93 119 136 Gx Gx G G Gy Gy 109+5.5 114+5.5 131+5.5 142+5.5 194+5.5 213+2 86+5.5 94+5.5 104+5.5 115+5.5 133+5.5 158+2 152 152 215 215 242 242 B1 B2 E1 H1 H2 L1 max. L2 3 22 23 24 25 28 30 102 102 138 138 165 165 118 118 163 163 165 165 13 13 25 25 25 25 13 17 17 19 19 27 14 14 14 14 17 17 L3 L4 L5 1 2
Note: This product conforms to ISO 1179-1 and ISO 228-1
2012/01 Subject to change
Internet: www.festo.com/catalog/...
43
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationOrdering data Modular products 0 Mandatory data M Module No. Function Piston Stroke Cushioning 0 Options O Position sensing Protection against rotation Type of piston rod
163 302 163 334 163 366 163 398 163 430 163 462 Order example 163 430 Ordering table Size 0 Module No. M Function Piston Stroke Cushioning
DNC
32 40 50 63 80 100
100 2,000
P PPV
A
Q
S2 S20
DNC
80
550
PPV
A
Q
S2
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
100 163 462
Condition Code s
Enter code
Standard cylinder, double-acting, standard hole pattern, cylinder/valve combination [mm] 32 40 50 63 80 100 [mm] 100 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Square piston rod Through piston rod Through, hollow piston rod2 S2
DNC - - -P -PPV 1 2 3 -A -Q -S2 -S20
DNC
0 Position sensing O Protection against rotation Type of piston rod
1
Q
Max. stroke: 100 1,500 mm In combination with S2: square piston rod at bearing cap end only In combination with KP: only supplied with S2 Not with S20, K7, K10, S10, S11
In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends In combination with K8: piston rod extended at bearing cap end only In combination with KP: clamping unit at end cap Not with S20, K7, S10, S11
3
S20 Max. stroke: 850 mm In combination with K8: piston rod extended at both ends Not with K2, K3, K5, K10, KP, S10, S11
Transfer order code DNC
44
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationOrdering data Modular products 0 Options O Extended male thread Female thread Special thread Special spanner flats Extended piston rod Improved running performan ce K10 Clamping unit Slow speed (constant motion) S10 Running characteri stics 0 M Cylinder/valve combination
K2
K3
K5
K7
K8
KP
S11
V1 V2 V3 V4 V5 V6
Ordering table Size
100K8
V2
32
40
50
63
80
100
Condition Code s 4 -K2 -K3 -K5 -K7 -K8 -K10 -KP -S10 -S11 -V1 -V2 -V3 -V4 -V5 -V6
Enter code
Extended male thread 0 O
Piston rod with extended male thread [mm] 1 35 1 70 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) Special thread Piston rod with special thread M10 M12 M16 M16 Special spanner flats Piston rod with external hexagon Extended piston rod Extended piston rod [mm] 1 500 Improved running performance Smooth anodised aluminium coated piston rod Clamping unit Attached Slow speed (constant motion) Slow speed (constant motion at low piston speeds) Running characteristics Low friction
(M12) M20
(M12) M20
5 6 7
8 9 aJ aA
0 Cylinder/valve combination M
Single solenoid valve, fitted on right, piston rod retracted when unactuated Single solenoid valve, fitted on right, piston rod advanced when unactuated Double solenoid valve, fitted on right Single solenoid valve, fitted on left, piston rod retracted when unactuated Single solenoid valve, fitted on left, piston rod advanced when unactuated Double solenoid valve, fitted on left8 9 aJ aA K10 Max. stroke: 1,000 mm Not with KP KP Without S2: position of the clamping unit at the bearing cap Not with S10, S11 S10 Max. stroke: 500 mm; additional strokes on request Not with S11 S11 Max. stroke: 500 mm; additional strokes on request
4 5 6 7
K2 K3 K5 K7
Not with K3, K10 With K5: on request Not with K7 Not with K10 Not with Q, S2, K10
Transfer order code
2012/01 Subject to change
Internet: www.festo.com/catalog/...
45
Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combinationAccessories Ordering data Valves For [mm] Single solenoid 32 40 50 63 80 100 Double solenoid 32 40 50 63 80 100 Ordering data Valve accessories For valve Push-in fitting QS CPE14 CPE18 CPE24 Plug socket KMYZ/KMEB CPE14 24 V DC, with PVC cable 0.5 m 24 V DC, with PVC cable 2.5 m CPE18 CPE24 24 V DC, with PVC cable 2.5 m, LED 24 V DC, with PVC cable 5 m, LED 24 V DC, with PVC cable 10 m, LED 153 015 153 018 153 020 Part No. Type Technical data QS-x-8-I QS--10-I QS-y-12-I PU1) Internet: quick star 10 10 10 Gx G Gy IP65 IP65 IP65 196 939 163 143 163 167 CPE14-M1BH-5J-x CPE18-M1H-5J- CPE24-M1H-5J-y Gx G Gy IP65 IP65 IP65 196 941 163 142 163 166 CPE14-M1BH-5L-x CPE18-M1H-5L- CPE24-M1H-5L-y Pneumatic connection Protection class Part No. Type Technical data Internet: cpe
Technical data Internet: plug socket with cable 185 519 KMYZ-4-24-0,5 185 520 151 688 151 689 193 457 KMYZ-4-24-2,5 KMEB-1-24-2,5-LED KMEB-1-24-5-LED KMEB-1-24-10-LED
Mounting kit ZVB CPE14 CPE18 CPE24 185 705 187 388 ZVB-8-14/18 ZVB-8-24
1)
Packaging unit quantity
46
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Accessories Multi-position kit DPNC Material: Flange: Wrought aluminium alloy Threaded studs, hex nuts: Galvanised steel
+ Dimensions and ordering data For F1 [mm] Note The maximum overall stroke length must not be exceeded when combining cylinders and multi-position kits. 32 40 50 63 80 100 125 27 27 32 28 38 38 48 Basic version 120 135 143 158 174 189 225
= plus stroke length
ZJ KP 165 188 210 234 269 287 350
Max. overall stroke length [mm] 1,000 1,000 1,000 1,000 1,000 1,000 1,000
Weight [g] 85 115 210 360 620 1,190 1,600
Part No.
Type
174 418 174 419 174 420 174 421 174 422 174 423 174 424
DPNC-32 DPNC-40 DPNC-50 DPNC-63 DPNC-80 DPNC-100 DPNC-125
Connecting two cylinders with identical piston diameter as a 3 or 4-position cylinder A 3 or 4-position cylinder consists of two separate cylinders whose piston rods advance in opposing directions. To achieve 3 positions Two cylinders with identical stroke length must be connected together. This means that depending on actuation and stroke division, this type of cylinder can assume up to four positions. In each case the cylinder is driven precisely against a stop. Note that when one end of the piston rod is To achieve 4 positions Two cylinders with different stroke lengths must be connected together. fixed, the cylinder barrel executes the movement. The cylinders connections must be flexible.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
47
Standard cylinders DNC, ISO 15552Accessories Foot mounting HNC/CRHNC Material: HNC: Galvanised steel CRHNC: High-alloy steel Free of copper, PTFE and silicone
+ Dimensions and ordering data For AB AH [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 1251)
= plus stroke length
AO
AT
AU
SA Basic version KP 187 214 237 261 305 318 375
TR
US
XA Basic version KP 189 216 242 266 310 328 395
XS
7 10 10 10 12 14.5 16.5
32 36 45 50 63 71 90
6.5 9 9.5 12.5 15 17.5 22
4 4 5 5 6 6 8
24 28 32 32 41 41 45
142 161 170 185 210 220 250
32 36 45 50 63 75 90
45 54 64 75 93 110 131
144 163 175 190 215 230 270
45 53 62 63 81 86 102
Basic version CRC1) Weight [g] 2 2 2 2 2 2 2 144 193 353 436 829 1,009 1,902
Part No. 174 369 174 370 174 371 174 372 174 373 174 374 174 375
Type HNC-32 HNC-40 HNC-50 HNC-63 HNC-80 HNC-100 HNC-125
High corrosion protection CRC1) Weight Part No. [g] 4 4 4 4 4 4 4 139 188 341 424 809 990 1,920 176 937 176 938 176 939 176 940 176 941 176 942 176 943
Type CRHNC-32 CRHNC-40 CRHNC-50 CRHNC-63 CRHNC-80 CRHNC-100 CRHNC-125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
48
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Accessories Flange mounting FNC/CRFNG Material: FNC: Galvanised steel CRFNG: High-alloy steel Free of copper, PTFE and silicone Cannot be used on the bearing cap in combination with the bellows kit DADB + = plus stroke length
Dimensions and ordering data For E [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 1251)
FB H13 7 9 9 9 12 14 16
MF
R
TF
UF
W Basic version
ZF KP 175 198 222 246 285 303 370
45 54 65 75 93 110 132 Basic version CRC1) Weight [g] 1 1 1 1 1 1 1 221 291 536 679 1,495 2,041 3,775
10 10 12 12 16 16 20
32 36 45 50 63 75 90
64 72 90 100 126 150 180
80 90 110 120 150 175 210
16 20 25 25 30 35 45
130 145 155 170 190 205 245
Part No. 174 376 174 377 174 378 174 379 174 380 174 381 174 382
Type FNC-32 FNC-40 FNC-50 FNC-63 FNC-80 FNC-100 FNC-125
High corrosion protection CRC1) Weight Part No. [g] 4 4 4 4 4 4 4 240 300 550 710 1,680 2,450 3,660 161 846 161 847 161 848 161 849 161 850 161 851 185 363
Type CRFNG-32 CRFNG-40 CRFNG-50 CRFNG-63 CRFNG-80 CRFNG-100 CRFNG-125
CRC1: Corrosion resistance class to Festo standard 940070 Components with light corrosion exposure. Protection for transport and storage. Components without significant decorative function or surface, e.g. installed out of sight internally or behind covers. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
49
Standard cylinders DNC, ISO 15552Accessories Trunnion flange ZNCF/CRZNG Material: ZNCF: Special steel casting CRZNG: Electrolytically polished special steel casting Free of copper, PTFE and silicone Cannot be used on the bearing cap in combination with the bellows kit DADB Dimensions and ordering data For C2 C3 [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 1251)
+
= plus stroke length
TD e9 12 16 16 20 20 25 25
TK
TL
TM
US
XH
XL Basic version KP 173 198 222 246 283 306 375
71 87 99 116 136 164 192 Basic version CRC1) Weight [g] 2 2 2 2 2 2 2 130 240 390 600 1,150 2,030 3,490
86 105 117 136 156 189 217
16 20 24 24 28 38 50
12 16 16 20 20 25 25
50 63 75 90 110 132 160
45 54 64 75 93 110 131
18 20 25 25 32 32 40
128 145 155 170 188 208 250
Part No. 174 411 174 412 174 413 174 414 174 415 174 416 174 417
Type ZNCF-32 ZNCF-40 ZNCF-50 ZNCF-63 ZNCF-80 ZNCF-100 ZNCF-125
High corrosion protection CRC1) Weight Part No. [g] 4 4 4 4 4 4 4 150 260 430 640 1,300 2,400 3,600 161 852 161 853 161 854 161 855 161 856 161 857 185 362
Type CRZNG-32 CRZNG-40 CRZNG-50 CRZNG-63 CRZNG-80 CRZNG-100 CRZNG-125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
50
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Accessories Trunnion mounting kit ZNCM for basic version DNC The mounting kit can be attached at any position along the profile barrel of a cylinder. Material: Tempered steel + = plus stroke length + = plus half stroke length for DNC-KP
1 Max. tightening torque
+ = plus stroke length + = plus half stroke length
1 Max. tightening torque
Dimensions and ordering data For B1 [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 1251)
C2
C3
TD e9 12 16 16 20 20 25 25 XV
TL
TM
UW Basic version
XG KP 111.1 128.6 150.6 169.1 198.9 211.8 259.7 Type
30 32 34 41 44 48 50 XJ
71 87 99 116 136 164 192
86 105 117 136 156 189 217
12 16 16 20 20 25 25 Max. tightening torque
50 63 75 90 110 132 160 CRC1)
65 75 95 105 130 145 175 Weight [g] 2 2 2 2 2 2 2 224 396 616 931 1,494 2,095 3,013
66.1 75.6 83.6 93.1 103.9 113.8 134.7 Part No.
KP 79.9 89.4 96.4 101.9 116.1 126.2 155.3 124.9 142.4 163.4 177.9 211.1 224.2 280.3 73 82.5 90 97.5 110 120 145
KP 118 135.5 157 173.5 205 218 270
[Nm] 4+1 8+1 8+2 18+2 28+2 28+2 40+2
163 525 163 526 163 527 163 528 163 529 163 530 163 531
ZNCM-32 ZNCM-40 ZNCM-50 ZNCM-63 ZNCM-80 ZNCM-100 ZNCM-125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
51
Standard cylinders DNC, ISO 15552Accessories Trunnion support LNZG Material: Trunnion support: Anodised aluminium Plain bearing: Polymer Free of copper, PTFE and silicone
Dimensions and ordering data For CR DA FK [mm] D11 H13 0.1 32 40, 50 63, 80 100, 1251)
FN
FS
H1
HB H13 6.6 9 11 14
KE
NH
TH 0.2
UL
CRC1)
Weight [g]
Part No.
Type
12 16 20 25
11 15 18 20
15 18 20 25
30 36 40 50
10.5 12 13 16
15 18 20 24.5
6.8 9 11 13
18 21 23 28.5
32 36 42 50
46 55 65 75
2 2 2 2
90 140 190 320
32 959 32 960 32 961 32 962
LNZG-32 LNZG-40/50 LNZG-63/80 LNZG-100/125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Trunnion support CRLNZG Material: High-alloy steel Free of copper, PTFE and silicone
Dimensions and ordering data For CR FK [mm] D11 0.1 32 40, 50 63, 80 100, 1251)
FN
FS
H1
HB H13 6.6 9 11 14
NH
TH 0.2
UL
CRC1)
Weight [g]
Part No.
Type
12 16 20 25
15 18 20 25
30 36 40 50
10.5 12 13 16
15 18 20 24.5
18 21 23 28.5
32 36 42 50
46 55 65 75
4 4 4 4
200 330 440 740
161 874 161 875 161 876 161 877
CRLNZG-32 CRLNZG-40/50 CRLNZG-63/80 CRLNZG-100
Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
52
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Accessories Swivel flange SNC Material: Die-cast aluminium
+ = plus stroke length 1 The pivot pin is protected against rotation with a dowel pin. Dimensions and ordering data For CG CP [mm] 32 40 50 63 80 100 1251)
H14 14 16 21 21 25 25 37
h14 34 40 45 51 65 75 97
EK H9 10 12 16 16 20 20 30
FL 0.2 22 25 27 32 36 41 50
L
SR
XC KP
CRC1)
Weight [g]
Part No.
Type
13 16 16 21 22 27 30
10 12 12 16 16 20 25
142 160 170 190 210 230 275
187 213 237 266 305 328 400
2 2 2 2 2 2 2
90 120 240 320 625 830 1,785
174 383 174 384 174 385 174 386 174 387 174 388 174 389
SNC-32 SNC-40 SNC-50 SNC-63 SNC-80 SNC-100 SNC-125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
53
Standard cylinders DNC, ISO 15552Accessories Swivel flange SNCB/SNCB--R3 Material: SNCB: Die-cast aluminium SNCB--R3: Die-cast aluminium with protective coating, high corrosion protection Free of copper, PTFE and silicone + Dimensions and ordering data For CB [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 1251)
= plus stroke length
H14 26 28 32 40 50 60 70 Basic version CRC1) Weight [g] 2 2 2 2 2 2 2 100 150 225 365 610 925 1,785
EK e8 10 12 12 16 16 20 25
FL 0.2 22 25 27 32 36 41 50
L
MR
UB h14
XC KP 142 160 170 190 210 230 275 187 213 237 266 305 328 400
13 16 16 21 22 27 30
8.5 12 12 16 16 20 25
45 52 60 70 90 110 130
Part No. 174 390 174 391 174 392 174 393 174 394 174 395 174 396
Type SNCB-32 SNCB-40 SNCB-50 SNCB-63 SNCB-80 SNCB-100 SNCB-125
Variant R3 High corrosion protection CRC1) Weight Part No. Type [g] 3 3 3 3 3 3 3 100 150 225 365 610 925 1,785 176 944 176 945 176 946 176 947 176 948 176 949 176 950 SNCB-32-R3 SNCB-40-R3 SNCB-50-R3 SNCB-63-R3 SNCB-80-R3 SNCB-100-R3 SNCB-125-R3
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
54
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Accessories Swivel flange SNCS Material: Die-cast aluminium
+ Dimensions and ordering data For CN EP [mm] H7 0.2 32 40 50 63 80 100 1251)
= plus stroke length
EX
FL 0.2
LT
MS
XC KP
CRC1)
Weight [g]
Part No.
Type
10 12 16 16 20 20 30
10.5 12 15 15 18 18 25
14 16 21 21 25 25 37
22 25 27 32 36 41 50
13 16 16 21 22 27 30
15 17 20 22 27 29 39
142 160 170 190 210 230 275
187 213 237 266 305 328 400
2 2 2 2 2 2 2
85 125 210 280 540 700 1,410
174 397 174 398 174 399 174 400 174 401 174 402 174 403
SNCS-32 SNCS-40 SNCS-50 SNCS-63 SNCS-80 SNCS-100 SNCS-125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Swivel flange SNCL Material: Die-cast aluminium Free of copper, PTFE and silicone
+ Dimensions and ordering data For CD EW [mm] H9 0.2/0.6 32 40 50 63 80 100 1251)
= plus stroke length
FL 0.2 22 25 27 32 36 41 50
L
MR
XC KP
CRC1)
Weight [g]
Part No.
Type
10 12 12 16 16 20 25
26 28 32 40 50 60 70
13 16 16 21 22 27 30
10 12 12 16 16 20 25
142 160 170 190 210 230 275
187 213 237 266 305 328 400
2 2 2 2 2 2 2
75 100 160 250 405 655 1,245
174 404 174 405 174 406 174 407 174 408 174 409 174 410
SNCL-32 SNCL-40 SNCL-50 SNCL-63 SNCL-80 SNCL-100 SNCL-125
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
2012/01 Subject to change
Internet: www.festo.com/catalog/...
55
Standard cylinders DNC, ISO 15552Accessories Ordering data Mounting attachments Designation For Part No. Clevis foot LNG 32 40 50 63 80 100 125 Clevis foot LSNG 32 40 50 63 80 100 125 Clevis foot LBG 32 40 50 63 80 100 125 31 761 31 762 31 763 31 764 31 765 31 766 31 767 LBG-32 LBG-40 LBG-50 LBG-63 LBG-80 LBG-100 LBG-125 31 740 31 741 31 742 31 743 31 744 31 745 31 746 LSNG-32 LSNG-40 LSNG-50 LSNG-63 LSNG-80 LSNG-100 LSNG-125 33 890 33 891 33 892 33 893 33 894 33 895 33 896 LNG-32 LNG-40 LNG-50 LNG-63 LNG-80 LNG-100 LNG-125 Technical data Part No. Type 5 561 5 562 5 563 5 564 5 565 5 566 6 987 LSN-32 LSN-40 LSN-50 LSN-63 LSN-80 LSN-100 LSN-125 Internet: clevis foot
Type
Designation Clevis foot LSN
For 32 40 50 63 80 100 125
Clevis foot for welding LSNSG 32 40 50 63 80 100 125 Right-angle clevis foot LQG 32 40 50 63 80 100 125
31 747 31 748 31 749 31 750 31 751 31 752 31 753
LSNSG-32 LSNSG-40 LSNSG-50 LSNSG-63 LSNSG-80 LSNSG-100 LSNSG-125
31 768 31 769 31 770 31 771 31 772 31 773 31 774
LQG-32 LQG-40 LQG-50 LQG-63 LQG-80 LQG-100 LQG-125 Technical data Type CRLNG-32 CRLNG-40 CRLNG-50 CRLNG-63 CRLNG-80 CRLNG-100 CRLNG-125 Internet: crlng
Ordering data Mounting attachments, corrosion-resistant Designation For Clevis foot CRLNG 32 40 50 63 80 100 125
Part No. 161 840 161 841 161 842 161 843 161 844 161 845 176 951
56
Internet: www.festo.com/catalog/...
Subject to change 2012/01
Standard cylinders DNC, ISO 15552Accessories Ordering data Piston rod attachments Designation For Part No. Rod eye SGS 32 40 50 63 80 100 125 Rod clevis SG 32 40 50 63 80 100 125 Coupling piece KSG 32 40 50 63 80 100 125 Adapter AD 32 40 157 333 157 334 160 256 160 257 AD-M10x1,25-x AD-M10x1,25- AD-M12x1,25- AD-M12x1,25-y Technical data Type CRSG-M10x1,25 CRSG-M12x1,25 CRSG-M16x1,5 CRSG-M20x1,5 CRSG-M27x2 Internet: crsg 6 144 6 145 6 146 6 147 14 987 SG-M10x1,25 SG-M12x1,25 SG-M16x1,5 SG-M20x1,5 SG-M27x2-B 9 261 9 262 9 263 9 264 10 774 SGS-M10x1,25 SGS-M12x1,25 SGS-M16x1,5 SGS-M20x1,5 SGS-M27x2 Technical data Part No. 32 954 10 767 10 768 10 769 10 770 Internet: piston rod attachment Type SGA-M10x1,25 SGA-M12x1,25 SGA-M16x1,5 SGA-M20x1,5 SGA-M27x2
Type
Designation Rod clevis SGA
For 32 40 50 63 80 100 125
Self-aligning rod coupler FK 32 40 50 63 80 100 125 Coupling piece KSZ 32 40 50 63 80 100 125
6 140 6 141 6 142 6 143 10 485
FK-M10x1,25 FK-M12x1,25 FK-M16x1,5 FK-M20x1,5 FK-M27x2
32 963 32 964 32 965 32 966 32 967
KSG-M10x1,25 KSG-M12x1,25 KSG-M16x1,5 KSG-M20x1,5 KSG-M27x2
36 125 36 126 36 127 36 128
KSZ-M10x1,25 KSZ-M12x1,25 KSZ-M16x1,5 KSZ-M20x1,5
Ordering data Piston rod attachments, corrosion-resistant Designation For Part No. Type Rod eye CRSGS 32 40 50 63 80 100 125 195 582 195 583 195 584 195 585 195 586 CRSGS-M10x1,25 CRSGS-M12x1,25 CRSGS-M16x1,5 CRSGS-M20x1,5 CRSGS-M27x2
Designation Rod clevis CRSG
For 32 40 50 63 80 100 125
Part No. 13 569 13 570 13 571 13 572 185 361
2012/01 Subject to change
Internet: www.festo.com/catalog/...
57
-V- NewBellows DADB Standard cylinders DNC, ISO 15552Accessories Bellows kit DADB
General technical data Type DADB-V6Max. cylinder stroke range1) Type of mounting Mounting position Resistance to media Ambient temperature2) Protection class Corrosion resistance class CRC3)1) 2)
32 [mm]
40
50 10 500
63 10 500
80 10 500
100 10 500
[C]
10 500 10 500 Via threaded pin Any Dust, chips, oil, grease, fuel ( 10 +80 IP54 3
Internet: media resistance)
In combination with the bellows kit DADB Note operating range of proximity sensors and cylinder Corrosion resistance class 3 as per Festo standard 940 070 Components with heavy corrosion exposure. Externally visible components in direct contact with normal industrial atmosphere or media such as solvents and cleaning agents, where the surface requirement is predominantly functional.
Materials Sectional view 5 1 2 3 4 Bellows 1 2 3 4 5 Connection Intermediate piece Bellows End piece Connector O-ring Note on materials Polyamide Polyamide Nitrile rubber Polyamide Polyamide Nitrile rubber Free of copper and PTFE RoHS-compliant
Weight [g] Type DADB-V6Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500
32 29 41 52 66 79 92 92 104 117 117
40 42 56 68 85 100 115 115 129 144 144
50 71 91 105 129 147 166 167 185 204 205
63 69 89 103 127 145 164 165 183 202 203
80 99 127 140 193 231 268 259 296 334 324
100 124 152 165 218 255 293 284 321 359 349
58
Internet: www.festo.com/catalog/...
Subject to change 2012/01
-V- NewBellows DADB Standard cylinders DNC, ISO 15552Accessories Travel velocity v as a function of tubing length l The bellows kit is a leak-free system. To prevent unwanted media being drawn in, the supply and exhaust air must be ducted via a venting hole in the connection part 1. The pressure generated in the bellows kit by the positioning motion is primarily defined by travel velocity and tubing length. The recommended tubing length based on the travel velocity of the drive can be read from the graph.
1
Advancing
Returning
32/50/63 40 Note The push-in fittings opposite must be used for the venting hole. Silencers can also be used as an alternative. This reduces the travel velocity slightly.
80/100
32 40
50/63 80/100
Tubing size and push-in fitting for venting hole Tubing O.D. [mm] [mm] 32, 40 8
Push-in fitting Part No. Type 186 109 533 929 533 880 186 350 533 848 533 884 QS-Gx-8-I QS-F-Gx-8-I QS-F-Gx-8H QS-G-12 QS-F-G-12 QS-F-G-12H
50, 63, 80, 100
12
2012/01 Subject to change
Internet: www.festo.com/catalog/...
59
-V- NewBellows DADB Standard cylinders DNC, ISO 15552Accessories Dimensions Download CAD Data www.festo.com/us/cad
+ Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 5001)
= plus stroke length
A21) 29 47 61 80 96 112 114 130 145 147
D1 max.
D2
32 EE
L1
L2
WH+A2 55 73 87 106 122 138 140 156 171 173
A21) 28 43 56 72 86 100 101 115 130 131
D1 max.
D2
40 EE
L1
L2
WH+A2 58 73 86 102 116 130 131 145 160 161
38
14
Gx
12.9
5.4
46
14
Gx
16.3
5.4
A21) 28 46 56 73 86 97 105 116 126 134
D1 max.
D2
50 EE
L1
L2
WH+A2 65 83 93 110 123 134 142 153 163 171
A21) 28 46 56 73 86 97 105 116 126 134
D1 max.
D2
63 EE
L1
L2
WH+A2 65 83 93 110 123 134 142 153 163 171
57
17
G
22.35
7
57
17
G
22.4
7
A21) 25 37 49 62 74 86 87 98 110 111
D1 max.
D2
80 EE
L1
L2
WH+A2 71 83 95 108 120 132 133 144 156 157
A21) 25 37 49 62 74 86 87 98 110 111
D1 max.
D2
100 EE
L1
L2
WH+A2 71 83 95 108 120 132 133 144 156 157
93
17
G
28
4
93
17
G
28
4
The dimension corresponds to the K8 value (extended piston rod) of the drive
60
Internet: www.festo.com/catalog/...
Subject to change 2012/01
-V- NewBellows DADB Standard cylinders DNC, ISO 15552Accessories Ordering data Bellows kit An extended piston rod (order code K8) is absolutely necessary when using a bellows kit. Ordering data Modular products. The necessary dimension for K8 as a function of piston diameter and cylinder stroke as well as the associated bellows kit is indicated in the following table: Order example: Selected standard cylinder: DNC-32-320-PPV-A- Dimension for the corresponding K8 value (see table): 112 mm Complete type designation for the standard cylinder: DNC-32-320-PPV-A--112K8 Associated bellows kit: DADB-V6-32-S301-350 Cylinder data Stroke [mm] 40 [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 Bellows kit Dimension Part No. Type for K8 [mm] 28 43 56 72 86 100 101 115 130 131 28 46 56 73 86 97 105 116 126 134 25 37 49 62 74 86 87 98 110 111 553 291 553 293 553 295 553 297 553 399 553 301 553 303 553 305 553 307 553 309 553 331 553 333 553 335 553 337 553 339 553 341 553 343 553 345 553 347 553 349 553 371 553 373 553 375 553 377 553 379 553 381 553 383 553 385 553 387 553 389 DADB-V6-40-S10-50 DADB-V6-40-S51-125 DADB-V6-40-S126-175 DADB-V6-40-S176-250 DADB-V6-40-S251-300 DADB-V6-40-S301-350 DADB-V6-40-S351-375 DADB-V6-40-S376-425 DADB-V6-40-S426-475 DADB-V6-40-S476-500 DADB-V6-63-S10-50 DADB-V6-63-S51-125 DADB-V6-63-S126-175 DADB-V6-63-S176-250 DADB-V6-63-S251-300 DADB-V6-63-S301-350 DADB-V6-63-S351-375 DADB-V6-63-S376-425 DADB-V6-63-S426-475 DADB-V6-63-S476-500 DADB-V6-100-S10-50 DADB-V6-100-S51-125 DADB-V6-100-S126-175 DADB-V6-100-S176-250 DADB-V6-100-S251-300 DADB-V6-100-S301-350 DADB-V6-100-S351-375 DADB-V6-100-S376-425 DADB-V6-100-S426-475 DADB-V6-100-S476-500
Cylinder data Stroke [mm] 32 [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476