Upload
endri
View
19
Download
0
Embed Size (px)
DESCRIPTION
dn7086754_711_en_global_pdf_online_a4.pdf
Citation preview
Flexi WCDMA BTS Optional ItemsDescription
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 1 (87)
471449A.909Nokia Flexi WCDMA Base Station, Rel. FlexiWBTS4.0 and Flexi WBTS4.5, ProductDocumentation, v.5
The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended for theuse of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted inany form or means without the prior written permission of Nokia Siemens Networks. Thedocumentation has been prepared to be used by professional and properly trained personnel,and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomescustomer comments as part of the process of continuous development and improvement of thedocumentation.
The information or statements given in this documentation concerning the suitability, capacity, orperformance of the mentioned hardware or software products are given as is and all liabilityarising in connection with such hardware or software products shall be defined conclusively andfinally in a separate agreement between Nokia Siemens Networks and the customer. However,Nokia Siemens Networks has made all reasonable efforts to ensure that the instructionscontained in the document are adequate and free of material errors and omissions. NokiaSiemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues whichmay not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NOEVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUTNOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESSOPPORTUNITY OR DATA, THAT MAYARISE FROM THE USE OF THIS DOCUMENT OR THEINFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark ofNokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners,and they are mentioned for identification purposes only.
Copyright Nokia Siemens Networks 2008. All rights reserved.
2 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Contents
Contents 3
Summary of changes in Flexi WCDMA BTS Optional ItemsDescription 5
1 Flexi mounting kit for floor, wall and pole (FMFA) description 9
2 Pole mounting kit (VMPB) description 13
3 Flexi Pole Installation Kit (FPIA) description 15
4 Flexi Pole Mounting Kit (FPKA) description 17
5 Flexi mounting covers for back and front (FMCA and FMCB)description 21
6 Flexi system external alarm box (FSEB) description 256.1 Flexi System External Alarm Box (FSEB) operation 256.2 Flexi System External Alarm (FSEB) dimensions and weight 256.3 Flexi system external alarm box (FSEB) interfaces 267 Flexi system external OVP (FSEC) description 29
8 Flexi system external GPS mediator (FSEG) description 318.1 Flexi System External GPS Mediator (FSEG) operation 318.2 Flexi System External GPS Mediator (FSEG) dimensions and weight 348.3 Flexi System External GPS Mediator (FSEG) interfaces 358.4 GPS antenna 36
9 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA)description 39
9.1 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA)operation 39
9.1.1 Operation 419.2 Flexi Power Module (FPMA) dimensions and weight 419.3 Flexi Power Module (FPMA) and sub-module (FPAA and FPBA)
interfaces 429.4 Flexi power sub-module (FPAA and FPBA) LED indications 4410 Flexi Power DC/DC Module (FPDA) description 4710.1 Flexi power DC/DC sub-module (FPDA) operation 4710.2 Flexi Power DC/DC Sub-module (FPDA) dimensions and weight 4810.3 Flexi power DC/DC sub-module (FPDA) interfaces 4910.4 Flexi power DC/DC sub-module (FPDA) LED indications 5011 Flexi Power AC/DC sub-module (FPAB) description 53
12 Flexi Cabinet for Indoor (FCIA) description 57
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 3 (87)
Contents
12.1 FCIA cabinet construction 5712.2 FCIA optional items 5812.3 FCIA dimensions and weight 59
13 Flexi Cabinet for Outdoor (FCOA) description 6113.1 Flexi Cabinet for Outdoor (FCOA) construction 6113.2 FCOA optional items 6213.3 FCOA dimensions and weight 66
14 Flexi Mounting Shield (FMSA and FMSB) description 6914.1 Flexi Mounting Shield (FMSA and FMSB) operation and construction 6914.2 Flexi Mounting Shield (FMSA and FMSB) dimensions and weights 7215 Flexi mounting kit vertical for 2G (FMUA) description 7315.1 Flexi mounting kit vertical for 2G (FMUA) operation 7315.2 Flexi mounting kit vertical for 2G (FMUA) construction 7515.3 Technical properties of Flexi Mounting Kit Vertical for 2G (FMUA) 7716 Flexi mounting kit horizontal for 2G (FMUB) description 7916.1 Flexi mounting kit horizontal for 2G (FMUB) operation and
construction 7916.2 Technical properties of Flexi Mounting Kit Horizontal for 2G (FMUB) 8017 I-HSPA Adapter description 8317.1 Overview of I-HSPA Adapter (FHAA) hardware 8317.2 Physical dimensions of the I-HSPA Adapter 8517.3 Physical interfaces of the I-HSPA Adapter 85
18 Talk Conversion Kit (EMIA) 87
4 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Summary of changes in Flexi WCDMA BTS Optional ItemsDescription
Changes between document issues are cumulative. Therefore, the latestdocument issue contains all changes made to previous issues.
Changes between issues 7-0 and 7-1
Section number removed from section Summary of changes in FlexiWCDMA BTS Optional Items Description.
Section Flexi System External GPS Mediator (FSEG) operation updatedwith GPS chaining information.
Changes between issues 6-0 and 7-0
Section Flexi Mounting Kit for Floor, Wall and Pole (FMFA) descriptionedited.
The title of section Technical properties of Flexi Mounting Kit Vertical for2G (FMUA) edited. Line "The loss of RF cables" added to the table.
The title of section Technical properties of Flexi Mounting Kit for Horizontalfor 2G (FMUB) edited. Line "The loss of RF cables" added to the table.
Section FCOA optional items edited.
Changes between issues 5-0 and 6-0
Earthquake requirements added to section Flexi mounting kit for floor, walland pole (FMFA) description.
Section Flexi Pole Installation Kit (FPIA) description added.
Section Flexi System External Alarm Box (FSEB) operation edited.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 5 (87)
Summary of changes in Flexi WCDMA BTS Optional ItemsDescription
Section Flexi System External Alarm (FSEB) dimensions and weightedited.
Section Flexi System External Alarm box (FSEB) interfaces edited.
Section Flexi system external OVP (FSEC) description edited.
Section Flexi System External GPS Mediator (FSEG) operation edited.
Section Flexi System External GPS Mediator (FSEG) dimensions andweight edited.
Section Flexi System External GPS Mediator (FSEG) interfaces edited.
Section Flexi Power Module (FPMA) and sub-module (FPAA and FPBA)interfaces edited.
Section FCIA cabinet construction edited.
Section FCIA optional items edited.
Section Flexi Cabinet for Outdoor (FCOA) construction edited.
Sections Overview of I-HSPA Adapter (FHAA) hardware, Physicaldimensions of the I-HSPA Adapter and Physical interfaces of the I-HSPAAdapter added under heading I-HSPA Adapter description.
Editorial changes made.
Changes between issues 4-0 and 5-0
Figure in section Pole Mounting Kit (VMPB) description updated.
Section Flexi Pole Mounting Kit (FPKA) Description added.
Section Flexi Mounting Covers for Back and Front (FMCA and FMCB)description updated with information on semi-transparent covers.
Section Flexi System External Alarm (FSEA) operation removed.
Section Flexi System External Alarm (FSEA) dimensions and weightremoved.
Section Flexi System External Alarm (FSEA) interfaces removed.
6 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Figure of the FSEB PWB added in section Flexi System External Alarm(FSEB) interfaces.
Section Flexi System External GPS Mediator (FSEG) operation added.
Section Flexi System External GPS Mediator (FSEG) dimensions andweight added.
Section Flexi System External GPS Mediator (FSEG) interfaces added.
Section Flexi System External Alarm Box (FSEB) dimensions and weightadded.
Figures in section Flexi Power Module (FPMA) and sub-modules (FPAAand FPBA) operation updated.
Figure of LED indication removed from section Flexi power DC/DC sub-module LED indications.
Section Flexi Power AC/DC sub-module (FPAB) description updated withinformation on FPAB LEDs and a figure of FPAB connectors added.
Section FCOA cabinet optional items updated with information on theFMBA and wind breaker.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 7 (87)
Summary of changes in Flexi WCDMA BTS Optional ItemsDescription
8 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
1 Flexi mounting kit for floor, wall and pole(FMFA) description
Flexi BTS modules are installed on the floor, wall or pole using Fleximounting kit for floor, wall and pole (FMFA). The FMFA consists of a plinthand adapter mechanics. It is a plinth that is required in BTS siteinstallations without a cabinet. The plinth provides grounding points forBTS and module grounding. The mounting principles are the following:
. In floor mounting, the plinth is fixed directly onto the floor. To meetthe Telcordia GR-63-CORE Vibrational requirements for earthquakeZone 4 requirement, the maximum number of modules in a stack isfive (maximum total height 15 U). To meet the Telcordia GR-63-CORE Vibrational requirements for earthquake Zone 2 requirement,the maximum number of modules in a stack is nine (maximum totalheight 22 U).
. In wall mounting, the plinth is fixed onto the wall either by usingadapter mechanics or directly to the wall. The maximum number ofmodules per plinth is two.
. In pole mounting, the plinth is fixed onto the pole mounting kit(VMPB) by using adapter mechanics. Adapters are needed toreduce the influence of non-parallel surfaces of the mountingbrackets. The maximum number of modules per plinth is two.
The FMFA delivery includes two fixing plates for the casings. Used inpole and wall installations, the plates are attached across twomodule casings on both sides of the modules.
See the following figure for an isometric view of the FMFA.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 9 (87)
Flexi mounting kit for floor, wall and pole (FMFA) description
Figure 1. Isometric view of the plinth
See the following figure for the adapter mechanics.
Figure 2. Adapter mechanics
DN7082497
DN7099438
10 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
The plinth has a back stop that prevents installing the BTS too near to awall (40 mm).
The compartment behind the front panel of the plinth is used as a storageplace, for example, for seal caps.
FMFA dimensions and weight
The dimensions and weight of the FMFA are presented in the followingtable.
Table 1. Dimensions and weight of the FMFA.
Property Value
Height 69 mm(2.7 in.)
Width 455 mm
(17.9 in.)Depth 459 mm
(18.1 in.)Weight wall configuration 7.3 kg (16 lbs)
floor configuration 6kg (13.2lbs)
The material of the plinth is 1.5 mm (0.06 in.) sheet metal.
For installation instructions, see Installing the Modules.
External connections
The plinth has the following fixing interfaces:
. ESD studs (2 pcs)
. Casing fixing points (4 pcs)
. Pole/wall adapter fixing points (6 pcs)
. Threads for the lifting eye bolts (4 pcs)
. Modules grounding (24 pcs)
. BTS grounding (1 pcs)
. Casing locking points (2 pcs)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 11 (87)
Flexi mounting kit for floor, wall and pole (FMFA) description
. Anchoring points to floor (4 main and 2 optional)
. Fixing plate fixing points (4 pcs)
See the following figure for the external fixing interfaces of the FMFA.
Figure 3. External interfaces of the plinth
Anchoring pointsto floor
Modules groundingBTS grounding
ESD Stud
Threads for thelifting eye bolts
Casing fixing points
Fixing holes forfixing plates
Casing lockingpoints
Casing lockingpoints
Fixing holes foradapter plates
DN7082504
12 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
2 Pole mounting kit (VMPB) descriptionThe pole mounting kit (VMPB) enables BTS installation on a pole 60-300mm (2.4-11.8 in.) in diameter.
See the following figure for an isometric view of the VMPB.
Figure 4. Pole mounting kit
See the following table for the delivery contents of the VMPB.
Table 2. Delivery contents
Item Quantity
Pole Mounting Kit (VMPB) 1Mounting blocks 2 pcs
M8x25 bolts 8 pcs
M10x120 bolts 4 pcs
M10x200 bolts 4 pcs
M10x300 bolts 4 pcs
Washers 4 pcs
DN70415461
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 13 (87)
Pole mounting kit (VMPB) description
See the following table for dimensions and weight of the VMPB.
Table 3. VMPB dimensions and weight
Property Value
Height 60 mm (2.4 in.)Width 350 mm (13.7 in.)Depth 300 mm (11.8)Weight 8.3 kg (18.3 lbs)
For installation instructions, see section Mounting the plinth on a pole inthe Installing the Modules document.
14 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
3 Flexi Pole Installation Kit (FPIA)description
Flexi Pole Installation Kit (FPIA) consists of an installation plate, strainingstrap and four screws. It is used for installing the following auxiliary units toa pole:
. Flexi System External Alarm (FSEB)
. Flexi System External OVP (FSEC)
. Flexi System External GPS Mediator (FSEG)
The pole can between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter.
There are two sets of fixing points on the installation plate. The FPIA cancarry the weight of 5 kg (11 lbs).
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 15 (87)
Flexi Pole Installation Kit (FPIA) description
16 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
4 Flexi Pole Mounting Kit (FPKA)description
The Flexi Pole Mounting Kit (FPKA) can be used with poles between 60mm (2.4 in.) and 120 mm (4.7 in.) in diameter. The most commonly usedsize is 80 mm (3.1 in.). The FPKA can replace the VMPB Pole Mounting kitin installations where the pole diameter is less than 120mm (4.7 in.).
See the following figure for the FPKA
Figure 5. Flexi Pole Mounting Kit (FPKA)
The width of the fixing points is 184 mm (7.2 in.) and 64 mm (2.5in.). Thereare fixing points in three sides of the FPKA. The M10 screws should betightened to 30Nm and the M8 screws 20 Nm. The FPKA can carry themaximum weight of 160 kg (352.7 lbs).
The delivery contents of the FPKA are listed in the following table.
Bolt M8x20
Bolt M10X120105 mm thread
Fixingpoints184mm (7.2 in.)
Fixingpoints64mm (2.5 in.)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 17 (87)
Flexi Pole Mounting Kit (FPKA) description
Item Quantity
FPKA Bracket 1 pcs.
Bolt M8 x 20 6 pcs.
Bolt restrainer 2 pcs.
FPKA bracket strainer 1 pcs.
Bolt M10 x120 105 mm thread
ISO 4762 (DIN912)2 pcs.
Installation with Remote Radio Heads
The FPKA has room for three Remote Radio Heads. It is possible to usethree installation directions. See the following figure for the FPKAinstallation with three Remote Radio Heads.
Figure 6. FPKA with three Remote Radio Heads
DN70424764
18 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Installation with RF Modules
The FPKA has room for four RF Modules (Single or Dual). Two RFModules can be installed on opposite sides of the FPKA. See the followingfigure for the FPKA installation with four RF Modules.
Figure 7. FPKA with four RF Modules
Installation with Metrosite 50
The FPKA supports the Metrosite 50 with two installation directions. Seethe following figure for the FPKA installation with Metrosite 50.
DN70424752
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 19 (87)
Flexi Pole Mounting Kit (FPKA) description
Figure 8. FPKA with Metrosite 50
DN70424776
20 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
5 Flexi mounting covers for back and front(FMCA and FMCB) description
Flexi mounting covers for back and front are optional 3U (FMCA) and 2U(FMCB) module covers that are required in installations without a cabinet.The primary functions of the covers are to provide protection against wind-driven rain, visual protection, and mechanical protection for the cables.Furthermore, the back cover protects the installer's fingers from therotating fans. The front cover air deflector is semi-transparent to allowassessing the status of the hardware LEDs without removing the frontcovers.
For installation instructions, see sections Installing covers in stackedinstallations and Installing covers in wall and pole installations in theInstalling the Modules document.
The FMCA and FMCB deliveries include a grounding cable. Note that it isnot included in any module deliveries.
The back and front covers, the safety catches and the grounding cable areillustrated in the following figure.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 21 (87)
Flexi mounting covers for back and front (FMCA and FMCB)description
Figure 9. FMCA: 3U back cover, 3U front cover, 2 x safety catch andgrounding cable.
FMCA dimensions
The dimensions of the FMCA are presented in the following table.
Table 4. Dimensions of the FMCA
Property Front cover Back cover
Height 128 mm(5 in.)
128 mm
(5 in.)Width 492 mm
(19.4 in.)446 mm
(17.6 in.)Depth 100 mm
(3.9 in.)37 mm
(1.5 in.)
DN7082516
Front cover Back cover
2 x safety catch Grounding cable
22 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Table 5. Dimensions of the FMCB
Property Front cover Back cover
Height 83 mm(3.3 in.)
83 mm
(3.3 in.)Width 492 mm
(19.4 in.)446 mm
(17.6 in.)Depth 100 mm
(3.9 in.)37 mm
(1.5 in.)
The material of the covers is plastic.
Table 6. Grounding cable
Property Value
Length 1.3 m (4.3 ft.)Thickness 16 mm2 (5 AWG)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 23 (87)
Flexi mounting covers for back and front (FMCA and FMCB)description
24 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
6 Flexi system external alarm box (FSEB)description
6.1 Flexi System External Alarm Box (FSEB) operation
The FSEB box is used for extending the Flexi BTS alarm connector tosupport up to 24 alarm interfaces. 12 alarms are supported for FlexiWCDMA BTS. Support for the fire detector is also provided. The FSEB boxprovides IP55 protection.
In outdoor applications, the box can be attached to the outdoor cabinetroof. There are fixing points for the FSEB in the outdoor cabinet. In indooror stacked applications, the box is attached in the proximity of themodules, for example, on a wall.
The Flexi Mounting Auxiliary Brackets (FMAA) can be used to mount theFSEB on the top or outer casings in pole, wall, and stack configurations.The brackets are mounted on the top or outer casing using the existingconnection pin holes. Flexi Pole Installation Kit (FPIA) can be utilised forpole installations.
For installation instructions, see section Installing Flexi System ExternalAlarm (FSEB) in the Installing Flexi WCDMA BTS Optional Itemsdocument.
6.2 Flexi System External Alarm (FSEB) dimensionsand weight
The dimensions and weight of the FSEB are presented in the followingtable.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 25 (87)
Flexi system external alarm box (FSEB) description
Table 7. FSEB dimensions
Property Value
Width 335 mm
(13.2 in.)Height 94 mm
(3.7 in.)Depth 182 mm
(7.2 in.)Weight Max. 2 kg
(4.4 lbs)
The mounting dimensions of the FSEB enclosure are 110 mm x 324 mm(4.3 in. x 12.8 in.).
The material of the box is plastic.
6.3 Flexi system external alarm box (FSEB) interfaces
See the figure below for the FSEB mechanical interfaces:
26 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Figure 10. FSEB interfaces
PWB interface
The PWB interface and connectors are presented in the table below.
Table 8. Interface and connector overview
Interface Type Description
EACX-I Sub-D37, female . 12 direct alarm inputs. 6 alarm outputs
(ESM extension,compatible to EAC onESM)
EACX-S 10 SMDK1/6-3.5 60 pin screw terminalcombines EACX-I, EACX-II
Fire detector powersupply
Screw terminal DC power supply for theoptional fire detector
ESM Sub-D37, male Interface to the SystemModule, *CAN bus
BTS interconnectioncable
UltraSite and Talkswap cases
EAC M16
Grounding point
DN70283679
ESD
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 27 (87)
Flexi system external alarm box (FSEB) description
Table 8. Interface and connector overview (cont.)
Interface Type Description
*EACX-II Sub-D37, female 12 alarm inputs via CANbus
*Not used in WCDMA mode.
See the following figure for the FSEB PWB.
Figure 11. FSEB PWB
DN70410509
ESM
EACX-II(D37)
EACX-I(D37)
grounding
Smoke-DetectorPower X4114
EACX-S screw terminalsX4104 to X4113
Not in use
28 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
7 Flexi system external OVP (FSEC)description
The FSEC protects Flexi WCDMA sub-modules against surge pulse(s) inpower feeding lines. This section describes protection device only for DClines in the feederless site solution. The same mechanics can also be usedfor AC line devices, but the connectors and OVP devices need to bechanged. The FSEC gives Class II (C, T2) protection for DC power feedand provides IP55 protection. For FSEC installation instructions, seesection Installing Flexi System External OVP (FSEC) in the Installing FlexiWCDMA BTS Optional Items document.
The FSEC box is also used for altering the DC cable diameter. For moredetailed information on the FSEC usage in the Feederless site solution,see Installing feederless site.
Figure 12. Isometric view of the FSEC
DN70154491
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 29 (87)
Flexi system external OVP (FSEC) description
FSEC dimensions
The dimensions of the Flexi system external OVP box are presented in thefollowing table. The FSEC is made of aluminium.
Table 9. FSEC dimensions
Property Value
Width 95 mm
(3.7 in.)Height 155 mm
(6.1 in.)Depth 155 mm
(6.1 in.)Weight 2.7 kg (5.9 lbs)
FSEC connectors
In the FSEC, there are screw terminals for input and output cables. Thereare four pieces of screw terminals for AWG 2 cables and for earthing twoPEs (Protecting earth GND) terminals for AWG 2 cable size.
30 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
8 Flexi system external GPS mediator(FSEG) description
8.1 Flexi System External GPS Mediator (FSEG)operation
Flexi System External GPS Mediator (FSEG) is used for providing IP55protected area for powering and connecting the GPS module (GPSAntenna Kit FYGA) to the BTS system. The FSEG is only used with theFSMB when GPS synchronisation is needed. No specific software isneeded for running the FSEG.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 31 (87)
Flexi system external GPS mediator (FSEG) description
Figure 13. GPS and FSEG usage
The FSEG has the following functionalities:
. transforming operating voltage to FYGA (from -48VDC to +12VDC)
. mediating GPS clock signal from FYGA to the BTS system
. overvoltage protection
EAC
AC in
48V DC
12V DC
30 (FYHA) or100m (FYHB)
BTS/Iub
DN70468865
32 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
The FSEG can be installed in the following ways:
. On a wall (vertical or horizontal position)
. On a pole using brackets (horizontal or vertical position) (optionalFlexi Pole Installation Kit FPIA)
. On stack installations using brackets (horizontal or vertical position)(optional Flexi Mounting Auxiliary Brackets FMAA)
. On the FCIA or FCOA roof (horizontal position only)
In outdoor applications, the FSEG can be attached to the outdoor cabinetroof (the maximum of one item can be installed next to the FSEG). Thereare fixing points for the FSEG in the outdoor cabinet. In indoorapplications, the FSEG can be attached to the indoor cabinet roof. Instacked applications, the FSEG is attached in the proximity of the BTS.
The FSEG can be installed either horizontally (cable lead-ins on the side)or vertically (cable lead-ins facing down). The FSEG can be attached to apole (using FPIA brackets) or to a wall (screw holes).
For installation instructions, see section Installing Flexi System ExternalGPS Mediator (FSEG) in the Installing Flexi WCDMA BTS Optional Itemsdocument.
It is possible to synchronize a maximum of five System Modules with GPSsynchronization source. Flexi Sync cable for indoor use (2 metres) isneeded between the modules. See the picture below for details.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 33 (87)
Flexi system external GPS mediator (FSEG) description
Figure 14. Flexi WCDMA BTS with GPS chaining
8.2 Flexi System External GPS Mediator (FSEG)dimensions and weight
The dimensions and weight of the FSEG are presented in the followingtable.
Table 10. FSEG dimensions and weight
Property Value
Width 335 mm
(13.2 in.)Height 94 mm
(3.7 in.)Depth 182 mm
(7.2 in.)Weight Max. 2 kg
(4.4 lbs)
EAC
AC in
48V DC
12V DC
BTS/IubEAC
Master BTSBTS 1...BTS n
Max n = 5
34 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
The material of the box is plastic.
8.3 Flexi System External GPS Mediator (FSEG)interfaces
The FSEG interfaces are presented in the table below.
Table 11. Interface and connector overview
Interface Type Description
BTS sync in MDR26 Synchronization interfaceto FSMB
BTS PSU Screw terminal -48VDC input from FSM(to support AWG8 cable)
GPS Module MDR26 Interface to FYGA
GND Screw terminal Module grounding
See the following figure for the FSEG printed wiring board.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 35 (87)
Flexi system external GPS mediator (FSEG) description
Figure 15. FSEG printed wiring board
8.4 GPS antenna
The GPS antenna with an integrated receiver has to be installed outsidefor satellite visibility. The antenna is directly connected to thesynchronisation input of the System Module.
DC power feed for the receiver is supplied through the combined powerand data cable. The System Module provides a power feed of 48 V DC thatis converted into 12 V DC using Flexi System External GPS Mediator(FSEG).
GPSMODULE
DN70454901
BTSSYNC IN
BTS PSU
GND
36 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
See also section Installing the GPS System in Installing Flexi WCDMABTS Optional Items.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 37 (87)
Flexi system external GPS mediator (FSEG) description
38 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
9 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description
9.1 Flexi Power Module (FPMA) and sub-modules(FPAA and FPBA) operation
Flexi Power Module (FPMA) is an optional module. It comprises FPMAmechanics and AC and DC interfaces. The actual power sub-modules arethe following:
. Flexi Power AC/DC sub-module 200-240 V AC (FPAA)
. Flexi Power Battery sub-module (FPBA)
The maximum number of sub-modules in an FPMA is four.
For installation instructions, see section Installing Flexi Power Module(FPMA) in the Installing Flexi WCDMA BTS Optional Items document.
The FPMA is presented in the following figures.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 39 (87)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA)description
Figure 16. Power Module (FPMA)
Figure 17. FPMA: full configuration with two FPAAs and two FPBAs
DN70230045
Type label
DN7084386
40 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
9.1.1 Operation
The FPMA can support 1-phase and 3-phase AC input. The nominal inputvoltage is 200-240 V AC (the operating voltage range is 180 - 276 V AC).The maximum output power from the FPMA is 4kW (with 4 FPAAs).Flexi Power AC-DC sub-module (FPAA)
The main function of the FPAA is to provide the BTS with nominal 48 V DCpower from an AC supply. Maximum DC output power of one FPAAmodule is 1000 W. A nominal 48 V DC supply is intended for BTS internaluse only (a nominal 48 V DC supply is not intended for 3rd partyequipment because they may require lower conducted emission level thanEN55022 Class A). It should be especially noted that an external lead acidbattery for longer backup times cannot be connected to nominal 48 V DCsupply. (This is because the temperature compensation of chargingvoltage is not supported). The FPAA includes its own integrated self-controlled fan. In case the fan fails, an alarm is generated and the FPAAhas to be replaced (the fan alone cannot be replaced).Flexi Power Battery sub-module (FPBA)
The Flexi Power Battery Sub-Module (FPBA) is a separate optional sub-module used together with the FPAA.
The FPBA provides short-term battery backup time when the AC powermains is down on a Flexi BTS site. The FPBA is a lithium ion battery. Themaximum DC output power from one FPBA module is 1000 W. The inputpower for the BTS cannot exceed the maximum output power of theinstalled batteries. Otherwise the batteries do not provide the BTS with theneeded power during power failure.
9.2 Flexi Power Module (FPMA) dimensions and weight
The following table lists the dimensions and weight for the Power Module.
Table 12. Dimensions and weight of the Power Module
Property FPMA
Height 133 mm/3 U(5.2 in.)
Width 447 mm
(17.6 in.)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 41 (87)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA)description
Table 12. Dimensions and weight of the Power Module (cont.)
Property FPMA
Depth without covers 422 mm(16.6 in.)
Depth with covers 560 mm(22.1 in.)
Weight (empty) < 11 kg(< 24.3 lbs)
Weight(fully equipped with one AC/DCpower module and batteries)
28 kg(61.9 lbs)
9.3 Flexi Power Module (FPMA) and sub-module (FPAAand FPBA) interfaces
FPMA front panel connectors
The connectors on the FPMA front panel, their types and purposes arelisted in the table below.
Table 13. FPMA front panel connectors, types and purposes
Connector Type Purpose
Power supply in Terminal block AC main power supply in
Power supply out 2-wire DC cable 4 x multi-beam
DC feed to the BTS
Grounding 2 x M5 Module grounding
FPAA front panel connectors
There is a stand-by switch on the front panel of the FPAA. The stand-byswitch is used for switching the FPAA unit ON/stand-by.
The connectors on the FPAA front panel, their types and purposes arelisted in the table below.
42 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Table 14. FPAA front panel connectors, types and purposes
Connector Type Purpose
AC cable connector Mate-N-Lock AC input
DC connector Multi-beam power supplyconnector
DC output
Alarm connector 2 x RJ-45* Alarms**
Operational state visualindication
tri-colour LED FPAA state or alarmindication
*for chaining
**Alarm 1 (AL01): AC input failure (alarm is sent when AC input voltage ismissing or it is out of range).
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,cooling fan failure, output power is low or over temperature shut down isON).FPBA front panel connectors
There is a stand-by switch on the front panel of the FPBA.
The connectors on the FPBA front panel, their types and purposes arelisted in the table below.
Table 15. FPBA front panel connectors, types and purposes
Connector Type Purpose
DC input/output connector Multi-beam power supplyconnector
DC input and output
Alarm connector 2 x RJ-45* Alarms**
Operational state visualindication
tri-colour LED FPBA state or alarmindication
*for chaining
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 43 (87)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA)description
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,output power is low or unit has reached end of it's life).
**Unit has an input for Alarm 1 (AL01) from FPAA unit (Alarm 1 is a triggerfor battery discharging).
9.4 Flexi power sub-module (FPAA and FPBA) LEDindications
FPAA LED indications
The FPAA LED indications are explained in the table below. Read theinformation on LED indications thoroughly. A blinking red LED does notalways require removing the module.
Table 16. FPAA LED indications
Colour Explanation
Yellow Stand-by (AC connected)Green Normal operation
Red Alarm or fault
Red, blinking Unit operating with abnormal input voltage
See the following figure for the location of the FPAA LED.
Figure 18. FPAA LED
DN70350654
LED
44 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
FPBA LED indications
The FPBA LED indications are explained in the table below.
Table 17. FPBA LED indications
Colour Explanation
Yellow Stand-by (DC connected from FPAA)Ggreen Normal operation, battery OK
Green, blinking slowly Charging
Green, blinking fast Discharging
Blinking fast between green and yellow Forced discharge mode
Red, blinking fast Minor alarm
Red Major alarm or fault
The LED's slow blinking frequency is 1 Hz (1 sec) and fast blinkingfrequency 2 Hz (0.5 sec).
See the following figure for the location of the FPBA LED.
Figure 19. FPBA LED
DN70350678
LED
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 45 (87)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA)description
46 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
10 Flexi Power DC/DC Module (FPDA)description
10.1 Flexi power DC/DC sub-module (FPDA) operation
Flexi power DC/DC sub-module (FPDA) is an optional stand-alone 2 kWDC/DC module.
The FPDA converts nominal 24 V DC input voltage (normally negativegrounded) 53-55 V DC output voltage. The 53-55 V DC is then distributedto BTS loads. A maximum of two FDPA modules can be connected inparallel using external connecting cables between the output connectorsof the two units.
Conducted emission level of the 53-55 V DC supply is according to thestandard EN55022 Class A. The 53-55 V DC supply is intended for BTSinternal use only (the 53-55 V DC supply is not intended for 3rd partyequipment because they may require lower conducted emission level thanEN55022 Class A). It should be especially noted that an external lead acidbattery cannot be connected to the 53-55 V DC supply (because thetemperature compensation for charging voltage is not supported).
The FPDA includes its own integrated self-controlled fan. In case the fanfails, an alarm is generated and the fan has to be replaced.
For installation instructions, see section Installing Flexi Power DC/DCModule 24V FPDA in the Installing Flexi WCDMA BTS Optional Itemsdocument.
The FPDA is presented in the following figure.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 47 (87)
Flexi Power DC/DC Module (FPDA) description
Figure 20. The power DC/DC sub-module
10.2 Flexi Power DC/DC Sub-module (FPDA)dimensions and weight
The following table lists the dimensions and weight for the FPDA.
Table 18. Dimensions and weight of the FPDA
Property Value
Height 90 mm (2U)(3.5 in.)
Width 447 mm
(17.6 in.)Depth without covers 422 mm
(16.6 in.)Depth with covers 560 mm
(22.1 in.)
DN70150502
48 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Table 18. Dimensions and weight of the FPDA (cont.)
Property Value
Weight < 15 kg(< 33.1 lbs)
10.3 Flexi power DC/DC sub-module (FPDA) interfaces
There is a stand-by switch on the front panel of the FPDA.
The connectors on the FPDA front panel, their types and purposes arelisted in the table below.
Table 19. FPDA front panel connectors, connector types and purposes
Connector Connector type Purpose
Input connector M10 bolts DC input
Output connector M10 bolts DC output
Alarm connectors 2 x RJ-45* Alarms**
*for chaining
**Alarm 1 (AL01): DC input failure (alarm is sent when DC input voltage ismissing or it is out of range).
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,cooling fan failure, output power is low or over temperature shut down isON).
The FPDA front panel is presented in the following figure.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 49 (87)
Flexi Power DC/DC Module (FPDA) description
Figure 21. Front panel of the FPDA
10.4 Flexi power DC/DC sub-module (FPDA) LEDindications
The FPDA has a tri-colour LED on the front panel to indicate theoperational status of the module and all fault conditions during operation.Read the information on LED indications thoroughly. A blinking red LEDdoes not always require removing the module.
The LED indications of the FPDA are listed and explained in the tablebelow.
Table 20. FPDA LED indications
Colour Explanation
Green Normal operation
Red Alarm or fault
Yellow Stand-by
Red, blinking Abnormal input voltage
DN70141402
DC Input cabling DC Output cablingAlarm cabling
LED
50 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 51 (87)
Flexi Power DC/DC Module (FPDA) description
52 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
11 Flexi Power AC/DC sub-module (FPAB)description
Flexi Power AC/DC sub-module 100/240V (FPAB) is a front-end rectifierassembly that converts AC input voltage to DC output voltage. The mainapplication for the FPAB is to operate as an AC/DC converter for the singleRF Module of the Flexi WCDMA BTS. In this application, the FPAB isinstalled on top of the 3U Single RF module core, in the free place of theunused filter.
For installation instructions, see sections Installing the FPAB (Astec) to asingle RF Module and Installing the FPAB (Efore) to a single RF Module inthe Installing Flexi WCDMA BTS Optional Items document.
See the following figure for an isometric view of the FPAB.
Figure 22. Isometric view of the FPAB
DN70265249
LED
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 53 (87)
Flexi Power AC/DC sub-module (FPAB) description
See the following table for FPAB input/output voltage.
Table 21. FPAB input/output voltage
Property Value
Nominal input voltage 100 - 240 V AC (single phase)Input voltage range 90 - 276 V AC
Output voltage 56 V DC at 500 W
See the following figure for the FPAB connectors
See the following figure for installing the FPAB in the RF Module.
DN70407333
DC output(multi-beam connector)
AC input(row connector)
A
B
54 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Figure 23. Installing the FPAB in the Single RF Module
FPAB dimensions
The dimensions of the FPAB are presented in the following table.
Table 22. FPAB dimensions
Property Value
Width 124 mm (4.9 in.)Height 73 mm (2.9 in.)Depth 345 mm (13.6 in.)Weight Max. 2.6 kg (5.7 lbs)
DN70286831
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 55 (87)
Flexi Power AC/DC sub-module (FPAB) description
The FPAB LED indications are explained in the following table.
Table 23. FPAB LED indications
Colour Explanation
Yellow Stand-by (AC connected)Green Normal operation
56 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
12 Flexi Cabinet for Indoor (FCIA)description
12.1 FCIA cabinet construction
Flexi BTS modules can be installed in optional indoor and outdoor BTScabinets.
The modules inserted into the cabinets are environmentally protected toIP54 level already; the casings and outdoor cabinet raise the protectionlevel of the modules to IP55. The cabinets do not carry any BTSfunctionality; there are no traditional backplanes or electronics.
The same optional cabinets can house Nokia Flexi EDGE and BBUmodules. Therefore, it is possible to build GSM/EDGE, WCDMA/HSPA ormultiradio (GSM/EDGE/WCDMA/HSPA/WIMAX) configurations.
The FCIA IP protection class is IP20.
In the indoor cabinet, the cable entries are located on top of the cabinetand the jumpers are connected directly to the modules.
The optional indoor cabinet can include the following optional items:
. Integrated long term battery backup solution (MIBBU)
. Flexi System External Alarm box (FSEB)
. Flexi System External OVP (FSEC)
. Flexi Cabinet Fire Detector (FCDA)
. 62/92 Ah batteries and Flexi Battery Mounting Kit for FCIA (FMBB)
The figure below presents Flexi Cabinet for Indoor (FCIA).
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 57 (87)
Flexi Cabinet for Indoor (FCIA) description
Figure 24. FCIA cabinet
12.2 FCIA optional items
Flexi BTS Indoor Cabinet (FCIA) can include the following optional items:Flexi System External Alarm Module (FSEB)
Flexi System External Alarm box (FSEB) is installed on the cabinet roofand contains 12 external alarms and 6 controls.
DN70253985
58 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Flexi System External OVP (FSEC)
Flexi System External OVP (FSEC) is installed on the cabinet roof.Fire Detector (FCDA)
The Fire Detector (FCDA) cables are routed to the Flexi System ExternalAlarm box (FSEB).Multi Integrated Battery Backup Solution (MIBBU)
The optional Multi Integrated Battery Backup solution (MIBBU) with aseparate battery can be installed in Nokia Flexi BTS Indoor Cabinet.
The Multi Integrated Battery Backup Solution consists of
. one power distribution unit (WPU) with one control unit (CU), and
. one to four rectifier power units (WPM).
The power distribution unit mainly distributes the input AC mains to therectifier units. The control unit controls the rectifier power units andmonitors the alarms in the event of low supply voltage, or if the MIBBUenters the battery backup mode in the event of an AC mains failure. Thealarm generated by the control unit is forwarded to the BTS O&M software.
Flexi Battery Mounting Kit for FCIA (FMBB)
Flexi Battery Mounting Kit (FMBB) is needed when using batteries or theMIBBU solution in FCIA. The mounting kit is installed at the bottom of thecabinet.
12.3 FCIA dimensions and weight
See the following table for the dimensions and weight of the Flexi Cabinetfor Indoor (FCIA).
Table 24. Dimensions and weight of Flexi Cabinet for Indoor (FCIA).
Property Value
Height 1800 mm / 40.5U(70.87 in.)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 59 (87)
Flexi Cabinet for Indoor (FCIA) description
Table 24. Dimensions and weight of Flexi Cabinet for Indoor (FCIA). (cont.)
Property Value
Width 600 mm
(23.62 in.)Depth 600 mm
(23.62 in.)Weight(empty cabinet)
62 kg(136 lbs.)
Free space for modules 36 U
60 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
13 Flexi Cabinet for Outdoor (FCOA)description
13.1 Flexi Cabinet for Outdoor (FCOA) construction
Flexi Cabinet for Outdoor (FCOA) has a cabinet core made of analuminium chassis enclosed with aluminium covers. The cabinet door canbe locked with a triangle door-open key. The cabinet can also be fitted withan optional security lock for additional protection. The FCOA itself does nothave any electrical functionality and therefore, it does not increase FlexiBTS site power consumption
The cabinet has the following functions:
. it provides the base station and cables protection against externaldamage and foreign objects
. it supports earthquake protection
. it houses the Flexi cabinet site support module (FCSA) that provideslong-term battery back-up and a 4U-high IP55-protected space forLine Terminal Equipment (LTE)
. together with Flexi cabinet air filter (FCFA), it protects the BTS inextremely dirty conditions
The FCOA provides earthquake protection for an installation of more thannine modules.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 61 (87)
Flexi Cabinet for Outdoor (FCOA) description
Figure 25. FCOA cabinet
13.2 FCOA optional items
This section describes the optional items of Flexi BTS Outdoor cabinet(FCOA).Air filter
The optional air filter (FCFA) can be added in case of extremely dirtyenvironment (for fresh air cooled modules). The optional air filter providescover for extremely dirty conditions by over-pressurizing the cabinet. TheFCFA delivery includes the air filter and a wind plate.
DN70138414
62 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
The air filter is installed in the back of the cabinet, replacing the originalback wall. It consists of a filter element, 8 x diagonal fans, a pressuresensor, a control logic, and back wall mechanics. The wind plate isinstalled in the cabinet door.
The control of the FCFA fans is based on a pressure sensor. The pressuresensor measures pressure inside the cabinet and this information is thenused for controlling the fan speed.
The air filter is presented in the following figure.
Figure 26. Air filter
DN70150526
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 63 (87)
Flexi Cabinet for Outdoor (FCOA) description
Site support module
The optional site support module (FCSA) can be used with the outdoorcabinet to provide long-term battery back-up time for the Flexi WCDMABTS and a space for installing Line Terminal Equipment (LTE) units. TheFCSA provides IP55 protected installation space for the PDU unit, IBBUAC interface box, rectifier units, LTE equipment, control card, heatexchanger, and fans.
There is a separate option for battery installation in the site supportmodule. Batteries are fixed and cabled using Flexi Mounting Kit forBatteries (FMBA). The kit contains battery cables, a cable from IBBU to thebattery cables for safe installation, rubber spacers, and front fixing parts tothe batteries.
The site support is presented in the following figure.
64 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Figure 27. Site support
Fire detector
The fire detector is installed on the cabinet roof, and the cables are routedto the Flexi System External Alarm (FSEB).
The following figure presents the fire detector.
DN70150538
LTE Space
Controlcard
Batteries
FMBA
HeatExchanger
MIBBU
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 65 (87)
Flexi Cabinet for Outdoor (FCOA) description
Figure 28. Fire detector
Overvoltage protection
Flexi System External OVP (FSEC) is IP-protected box for overvoltageprotection and power terminals. FSEC is installed on the cabinet roof. Formore information on FSEC, see Flexi System External OVP (FSEC)description.
13.3 FCOA dimensions and weight
See the following table for the dimensions and weight of the Flexi Cabinetfor Outdoor (FCOA).
Table 25. Dimensions and weight of the Flexi Cabinet for Outdoor (FCOA)
Property Value
Height 1550 mm(61 in.)
Width 770 mm
(30.3 in.)
DN70150541
66 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Table 25. Dimensions and weight of the Flexi Cabinet for Outdoor (FCOA)(cont.)
Property Value
Depth 770 mm(30.3 in.)
Depth with air filter 930 mm(36.6 in.)
Depth with air filter and wind breaker 1020 mm(40.2 in.)
Weight(empty cabinet)
Max. 80 kg(177 lbs)
Weight(with air filter)
104 kg(230 lbs)
Weight(with air filter and wind breaker)
110 kg(243 lbs)
Total weight(Fully equipped with batteries)
365 kg(807 lbs)
Free space for modules 40 U(30 U horizontally + 5 U + 5 U vertically
Free space for modules(site support and batteries installed)
21 U
(16 U horizontally + 5 U vertically)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 67 (87)
Flexi Cabinet for Outdoor (FCOA) description
68 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
14 Flexi Mounting Shield (FMSA and FMSB)description
14.1 Flexi Mounting Shield (FMSA and FMSB) operationand construction
Flexi Mounting Shield (FMSA/FMSB) is an outdoor cabinet for a stackedFlexi BTS. Used instead of the plastic front and rear covers, it providesprotection against solar load, large insects and slight vandalism. FlexiMounting Kit Floor/Wall/Pole (FMFA) is required in both cabinets.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 69 (87)
Flexi Mounting Shield (FMSA and FMSB) description
Figure 29. Isometric view of the FMSA
DN70324735
70 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Figure 30. Isometric view of the FMSB
The FMSA provides installation space for up to any two Flexi 3U modulesand the plinth (6U in total). It is installed on a pole or wall.
The FMSB provides space for up to any six Flexi 3U modules and theplinth (18U in total). It is installed on the floor.
DN70324723
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 71 (87)
Flexi Mounting Shield (FMSA and FMSB) description
Flexi 3U Mounting Covers front/back (FMCA) as well as RF Module andSystem Module cable entries are not used in mounting shield installations.The cabinet door is right-handed (the handedness cannot be changed).
For installation instructions, see sections Installing Flexi Mounting Shield6U (FMSA) and Installing Flexi Mounting Shield 18U (FMSB) in theInstalling Flexi WCDMA BTS Modules in Cabinets document.
14.2 Flexi Mounting Shield (FMSA and FMSB)dimensions and weights
See the following table for the dimensions and weight of the FlexiMounting Shields (FMSA/FMSB).
Table 26. Dimensions and weight of Flexi Mounting Shield 6U (FMSA)
Property Value
Height 605 mm (23.8 in.)Width 400 mm (15.7 in.)Depth 620 mm (24.4 in.)Weight (empty) 12 kg (26.5 lbs.)Free space for modules 6U
Table 27. Dimensions and weight of Flexi Mounting Shield 18U (FMSB)
Property Value
Height 930 mm (36.6 in.)Width 605 mm (23.8 in.)Depth 620 mm (24.4 in.)Weight (empty) 21 kg (46.3 lbs.)Free space for modules 18U
72 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
15 Flexi mounting kit vertical for 2G (FMUA)description
15.1 Flexi mounting kit vertical for 2G (FMUA) operation
With Flexi Mounting Kit Vertical for 2G, Nokia Flexi modules can beinstalled on existing GSM/EDGE UltraSite sites. The mounting kit can beused with the following indoor and outdoor GSM/EDGE UltraSite cabinets:
. UltraSite EDGE BTS (CRMA)
. UltraSite Indoor cabinet (IDCA) 101
. UltraSite Outdoor cabinet (ODCA) 101
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 73 (87)
Flexi mounting kit vertical for 2G (FMUA) description
Figure 31. FMUA with WCDMA BTS installed
Before the mounting kit can be installed, the following parts are removedfrom the lower half of the GSM/EDGE UltraSite cabinet:
. 3 x fans,
. RFU back plane,
. WBC fan box.
The mounting kit consists of one dual rack in which one System Moduleand one RF Module are installed, one single rack for the second RFModule installation, and cables. There is a remaining space of 1 U in thesingle rack when the RF Module is installed.
2G
SystemModule
RF Module
DN7082146
1 U free space
74 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
For installation instructions, see section Overview of installing modules incabinet with Flexi Mounting Kit Vertical for 2G in the Installing FlexiWCDMA BTS Modules in Cabinets document.
15.2 Flexi mounting kit vertical for 2G (FMUA)construction
The mounting kit dual rack and single racks are made of aluminium andinclude mounting for fans and air ducts. See the following figure forillustration of the racks.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 75 (87)
Flexi mounting kit vertical for 2G (FMUA) description
Figure 32. FMUA parts (dual and single racks)
FRONT BACK
FRONT BACK
Dual rack
Single rack
DN7082037
76 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
15.3 Technical properties of Flexi Mounting Kit Verticalfor 2G (FMUA)
The following table illustrates the dimensions and weights of the two racksof the mounting kit.
Property Dual rack Single rack
Height 694 mm(27.3 in.)
585 mm
(23 in.)Width 302 mm
(11.9 in.)196 mm
(7.7 in.)Depth 395 mm
(15.6 in.)400 mm
(15.8 in.)Weight 6.2 kg
(13.7 lbs)4.6 kg(10.2 lbs)
The loss of RF cables 0.7dB 0.7dB
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 77 (87)
Flexi mounting kit vertical for 2G (FMUA) description
78 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
16 Flexi mounting kit horizontal for 2G(FMUB) description
16.1 Flexi mounting kit horizontal for 2G (FMUB)operation and construction
With Flexi Mounting Kit Horizontal for 2G, Nokia Flexi modules can beinstalled on existing GSM/EDGE UltraSite sites. The mounting kit can beused with the following indoor and outdoor GSM/EDGE UltraSite cabinets:
. UltraSite Indoor cabinet (IDCA) v.202 or newer
. UltraSite Outdoor cabinet (ODCA) v.202 or newer
. UltraSite EDGE Outdoor cabinet (ODCF)
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 79 (87)
Flexi mounting kit horizontal for 2G (FMUB) description
Figure 33. Isometric view of Flexi mounting kit horizontal for 2G
The mounting kit consists of a rack in which, for example, one WCDMASystem Module, up to three WCDMA RF Modules and one FPMA orSystem Extension Module or FPDA are installed, and cables. The spacerequirement for 5 x 3U modules is 15U.
For installation instructions, see section Installing modules in cabinet withFlexi Mounting Kit Horizontal for 2G in the Installing Flexi WCDMA BTSModules in Cabinets document.
16.2 Technical properties of Flexi Mounting KitHorizontal for 2G (FMUB)
The following table illustrates the dimensions and weight of the FMUB.
DN70231874
80 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
Property FMUB
Height 732 mm (28.8 in.)Width 525 mm (20.7 in.)Depth 393 mm (15.5 in.)Weight of the side wall 1.73kg (3.8 lbs)Weight(cables excluded)
Max. 20 kg (44 lbs)
The loss of RF cables 0.7dB
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 81 (87)
Flexi mounting kit horizontal for 2G (FMUB) description
82 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
17 I-HSPA Adapter description17.1 Overview of I-HSPA Adapter (FHAA) hardware
The I-HSPA Adapter (FHAA) has been designed as a 1U high 19-inch rackelement to be installed in any BTS cabinet or enclosure where the FlexiBTS can be installed, such as the Nokia Siemens Networks Flexi BTSindoor and outdoor cabinets, the Nokia Siemens Networks UltraSite GSM/EDGE cabinet, with either horizontal or vertical fixing kit; and standard 19-inch equipment racks.
Figure 34. Nokia Siemens Networks I-HSPA Adapter
The I-HSPA Adapter can be fitted to a Flexi BTS 2U module casing. Whenused with the Flexi BTS module casing, the I-HSPA Adapter can beinstalled with the Flexi WCDMA BTS in stand-alone configurations, suchas free-standing, wall mounted or pole mounted.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 83 (87)
I-HSPA Adapter description
Figure 35. I-HSPA Adapter and Flexi BTS module casing
The I-HSPA Adapter uses forced air cooling based on fresh air intake fromback to front. This allows it be installed either horizontally or vertically. Thecontents of the I-HSPA Adapter delivery also include and air-blockingplate, to be used if the I-HSPA Adapter is with the Flexi BTS 2U modulecasing.
The I-HSPA Adapter features a lightweight aluminium alloy casing withstainless steel alloy used for the fan carrier.
Figure 36. Views of I-HSPA Adapter
Rear Cover
Casing
I-HSPA Core mechanics
Front Cover
DN70287651
84 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
17.2 Physical dimensions of the I-HSPA Adapter
The I-HSPA Adapter is mechanically compatible with Flexi BTS 2U modulecasing.
Table 28. Dimensions of I-HSPA Adapter, including fan module
Width 441.6 mm (not including fixing points)Height 41 mm
Depth 299 mm
Weight 6.5 kg
Table 29. Dimensions of I-HSPA adapter with Flexi BTS 2U casing
Width 465 mm (between fixing points)Height 84.1 mm
Depth 395 mm
Weight 12.5 kg
17.3 Physical interfaces of the I-HSPA Adapter
All external connections to the I-HSPA Adapter are made through the frontpanel.
Table 30. Physical interfaces of the I-HSPA Adapter
Front panelidentifier Purpose Interface type Connector Type
BTS/Iub BTS interface 10/100/1000 Base-T Ethernet
RJ45 shielded
SFP/Ext 1 External transport Optical for Ethernet(reserved for futureuse)
SFP, SFP cage
Ext 2
Ext 3
External transport 10/100/1000 Base-T Ethernet
RJ45 shielded
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 85 (87)
I-HSPA Adapter description
Table 30. Physical interfaces of the I-HSPA Adapter (cont.)
Front panelidentifier Purpose Interface type Connector Type
DC IN 48VDC PowerInput
Multi-Beam XL RA2 pin
Figure 37. Front panel of the I-HSPA Adapter
DC IN EIF1
EIF2 EIF3 EIF4DN70282859
86 (87) # Nokia Siemens Networks DN7086754Issue 7-1 en31/10/2008
Flexi WCDMA BTS Optional Items Description
18 Talk Conversion Kit (EMIA)Flexi WCDMA BTS modules can be installed into the CityTalk cabinet byusing the Talk conversion kit EMIA. The inner parts of the CityTalk cabinetare removed before the Flexi WCDMA modules are installed and certainparts of the CityTalk cabinet are replaced with new parts belonging to theEMIA kit
The CityTalk cabinet retains its outline dimensions and the mechanicalshape when modified with EMIA. The Flexi WCDMA BTS within themodified cabinet fulfills the Flexi WCDMA temperature and IPrequirements. It is also possible to equip the cabinet with an optional airfilter kit.
DN7086754Issue 7-1 en31/10/2008
# Nokia Siemens Networks 87 (87)
Talk Conversion Kit (EMIA)
Flexi WCDMA BTS Optional Items DescriptionContentsSummary of changes in Flexi WCDMA BTS Optional Items Description1 Flexi mounting kit for floor, wall and pole (FMFA) description2 Pole mounting kit (VMPB) description3 Flexi Pole Installation Kit (FPIA) description4 Flexi Pole Mounting Kit (FPKA) description5 Flexi mounting covers for back and front (FMCA and FMCB) description6 Flexi system external alarm box (FSEB) description6.1 Flexi System External Alarm Box (FSEB) operation6.2 Flexi System External Alarm (FSEB) dimensions and weight6.3 Flexi system external alarm box (FSEB) interfaces
7 Flexi system external OVP (FSEC) description8 Flexi system external GPS mediator (FSEG) description8.1 Flexi System External GPS Mediator (FSEG) operation8.2 Flexi System External GPS Mediator (FSEG) dimensions and weight8.3 Flexi System External GPS Mediator (FSEG) interfaces8.4 GPS antenna
9 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description9.1 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) operation9.1.1 Operation
9.2 Flexi Power Module (FPMA) dimensions and weight9.3 Flexi Power Module (FPMA) and sub-module (FPAA and FPBA) interfaces9.4 Flexi power sub-module (FPAA and FPBA) LED indications
10 Flexi Power DC/DC Module (FPDA) description10.1 Flexi power DC/DC sub-module (FPDA) operation10.2 Flexi Power DC/DC Sub-module (FPDA) dimensions and weight10.3 Flexi power DC/DC sub-module (FPDA) interfaces10.4 Flexi power DC/DC sub-module (FPDA) LED indications
11 Flexi Power AC/DC sub-module (FPAB) description12 Flexi Cabinet for Indoor (FCIA) description12.1 FCIA cabinet construction12.2 FCIA optional items12.3 FCIA dimensions and weight
13 Flexi Cabinet for Outdoor (FCOA) description 13.1 Flexi Cabinet for Outdoor (FCOA) construction13.2 FCOA optional items13.3 FCOA dimensions and weight
14 Flexi Mounting Shield (FMSA and FMSB) description14.1 Flexi Mounting Shield (FMSA and FMSB) operation and construction14.2 Flexi Mounting Shield (FMSA and FMSB) dimensions and weights
15 Flexi mounting kit vertical for 2G (FMUA) description15.1 Flexi mounting kit vertical for 2G (FMUA) operation15.2 Flexi mounting kit vertical for 2G (FMUA) construction15.3 Technical properties of Flexi Mounting Kit Vertical for 2G (FMUA)
16 Flexi mounting kit horizontal for 2G (FMUB) description16.1 Flexi mounting kit horizontal for 2G (FMUB) operation and construction16.2 Technical properties of Flexi Mounting Kit Horizontal for 2G (FMUB)
17 I-HSPA Adapter description17.1 Overview of I-HSPA Adapter (FHAA) hardware17.2 Physical dimensions of the I-HSPA Adapter17.3 Physical interfaces of the I-HSPA Adapter
18 Talk Conversion Kit (EMIA)