Dn0114587 5 en Global PDF Online a4

WV - GSM Network and NetworkElement Specific NumberHandling (MSC and HLR)

dn0114587Issue 2-0 en

# Nokia CorporationNokia Proprietary and Confidential

1 (66)

SG10038.01Nokia 2G SGSN Release 3 ProductDocumentation

The information in this documentation is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended for theuse of Nokia's customers only for the purposes of the agreement under which the documentationis submitted, and no part of it may be reproduced or transmitted in any form or means without theprior written permission of Nokia. The documentation has been prepared to be used byprofessional and properly trained personnel, and the customer assumes full responsibility whenusing it. Nokia welcomes customer comments as part of the process of continuous developmentand improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, orperformance of the mentioned hardware or software products cannot be considered binding butshall be defined in the agreement made between Nokia and the customer. However, Nokia hasmade all reasonable efforts to ensure that the instructions contained in the documentation areadequate and free of material errors and omissions. Nokia will, if necessary, explain issueswhich may not be covered by the documentation.

Nokia's liability for any errors in the documentation is limited to the documentary correction oferrors. NOKIA WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL(INCLUDING MONETARY LOSSES), that might arise from the use of this documentation or theinformation in it.

This documentation and the product it describes are considered protected by copyrightaccording to the applicable laws.

NOKIA logo is a registered trademark of Nokia Corporation.

Other product names mentioned in this documentation may be trademarks of their respectivecompanies, and they are mentioned for identification purposes only.

Copyright © Nokia Corporation 2003. All rights reserved.

2 (66) # Nokia CorporationNokia Proprietary and Confidential


WV - GSM Network and Network Element Specific Number Handling (MSC and HLR)

Contents

Contents 3

List of tables 4

List of figures 5

Summary of changes 7

WV: GSM NETWORK AND NETWORK ELEMENT SPECIFIC NUMBERHANDLING 9

1 WVC: CREATE MSC NUMBER RANGE 11

2 WVD: DELETE MSC NUMBER RANGE 17

3 WVM: MODIFY MSC NUMBER RANGE 21

4 WVJ: INTERROGATE MSC NUMBER RANGE 27

5 WVS: CREATE NETWORK AND NETWORK ELEMENT SPECIFICNUMBER 31

6 WVR: DELETE NETWORK AND NETWORK ELEMENT SPECIFICNUMBER 43

7 WVF: MODIFY NETWORK AND NETWORK ELEMENT SPECIFICNUMBER 49

8 WVI: INTERROGATE NETWORK AND NETWORK ELEMENTSPECIFIC NUMBER 59



3 (66)

Contents

List of tables

Table 1. Values for TON parameter in WVC command 12

Table 2. Values for HTON parameter in WVM command 22

Table 3. Values for TON parameter in WVS command 37

Table 4. Values for AN parameter in WVS command 38

Table 5. Values for BN parameter in WVS command 38

Table 6. Values for TON parameter in WVR command 47

Table 7. Values for TON parameter in WVF command 55




List of figures



5 (66)

List of figures




Summary of changes

Summary of changes

Changes between document issues are cumulative. Therefore, the latest documentissue contains all changes made to previous issues.

Changes made between issues 2�0 and 1�0

The following changes have been made:

. NEPRE parameter has been added to command M.

. EPRE parameter has been added to commands C, D, M, and J.

. TRIGSC, TRIGAC, and TMSISDN parameters have been added tocommands S, R, F, and I.

. CNID parameter has been added to commands S, R, F, and I.

. CIC1P and CIC2P parameters have been added to commands S, F, and I.

. RNGP parameter is not optional in commands C, M, D, and J. RNGP isalways visible.



7 (66)

Summary of changes




WV: GSM NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER HANDLING

Note that the command groups for the MSC and the HLR are slightly different. Inthis command group the commands C, D, M and J concern the MSC only.

You can use the commands of the command group to create, delete, modify, andinterrogate network and network element specific numbers.

You need the commands of this command group when you configure handoversor roamings in the network. The specific numbers are needed when setting up, forexample, the mobile network code to the system.

All numbers are stored in the GSM Network and Network-Element-SpecificNumber File (HRNFIL). ESKIMO uses the GSM Network and Network-SpecificNumbers Program Block (KAYAKS) to handle HRNFIL.

After each change HRNFIL is distributed to the computer units which use it.

Menu of the command group

GSM NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER HANDLING COMMANDS

? ..... DISPLAY MENU

C: ..... CREATE MSC NUMBER RANGE

D: ..... DELETE MSC NUMBER RANGE

M: ..... MODIFY MSC NUMBER RANGE

J: ..... INTERROGATE MSC NUMBER RANGE

S: ..... CREATE NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

R: ..... DELETE NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

F: ..... MODIFY NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

I: ..... INTERROGATE NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

Z; ..... RETURN TO MAIN LEVEL

WV: GSM NETWORK AND NETWORK ELEMENT SPECIFIC NUMBERHANDLING

The commands in this command group are:

WVC CREATE MSC NUMBER RANGE

WVD DELETE MSC NUMBER RANGE

WVM MODIFY MSC NUMBER RANGE

WVJ INTERROGATE MSC NUMBER RANGE

WVS CREATE NETWORK AND NETWORK ELEMENTSPECIFIC NUMBER



9 (66)

WV: GSM NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER HANDLING

WVR DELETE NETWORK AND NETWORK ELEMENTSPECIFIC NUMBER

WVF MODIFY NETWORK AND NETWORK ELEMENTSPECIFIC NUMBER

WVI INTERROGATE NETWORK AND NETWORK ELEMENTSPECIFIC NUMBER




1 WVC: CREATE MSC NUMBER RANGEFunction

Use this command to create MSC number ranges in the MSC.

Parameters

handover number,mobile station roaming number,emergency services routing key<option>:

type of number,MSRN group,ESRK range index <option>,ESRK prefix<option>;

Syntax

WVC:(HON=<handover number>...|

MSRN=<mobile station roaming number>...|

ESRK=<emergency services routing key> <option>...):

[TON=<type of number> |

[RNGP=<MSRN group> | 0 def] |

EIDX=<ESRK range index> <option> |

EPRE=<ESRK prefix> <option>];

Parameter explanations

handover number

HON= The starting and ending points of thehandover number range separated with the'&&' signs. The maximum length of thenumber is 18 digits. Both numbers musthave the same number of digits. Handovernumbers can be either national orinternational and therefore the type of thenumber must be specified in the secondparameter block. If an internationalnumber is used, the number must beginwith your own country code. Themaximum HON range is 200.



11 (66)

WVC: CREATE MSC NUMBER RANGE

mobile station roaming number

MSRN= The starting and ending points of theroaming number range separated with the'&&' signs. The maximum length of thenumber is 18 digits. Both numbers musthave the same amount of digits. The lastdigit of the starting number must be 0 andthe last digit of the ending number mustbe 9. Roaming numbers are in theinternational format and therefore thenumber must begin with your owncountry code.

emergency services routing key <option>

ESRK= The starting and ending points of theemergency services routing key rangeseparated with the '&&' signs. The startingand ending numbers must have 7 digits.The maximum emergency servicesrouting key range is 65535.

type of number

Table 1. Values for TON parameter in WVC command

Parameter Value Description

TON= NAT in national format

INT in international format

Give this parameter only if the first parameter is HON.

MSRN group

RNGP= The MSRN group can have values from 0to 50.

ESRK range index <option>




EIDX= The ESRK range index can be given onlyif the emergency services routing keyparameter is given. The ESRK rangeindex can have values from 1 to 100. Ifthe ESRK range index is not given, theESRK range index is defined by thesystem.

ESRK prefix <option>

EPRE= The ESRK prefix can be given only if theemergency services routing key parameteris given. The ESRK prefix can havevalues from 0 to 999. If the ESRK prefixis not given, the ESRK prefix is definedby the system.

Examples

1. Reserve number 12345600 to be used as a handover number in nationalformat.

WVC:HON=12345600:TON=NAT;

2. Reserve numbers 44345800..44345859 and 44345900..44345979 to beused as roaming numbers.

WVC:MSRN=44345800&&44345859&44345900&&44345979;

3. Reserve numbers 12345000..12345099 to be used as roaming numbers.Put them to MSRN group 1.

WVC:MSRN=12345000&&12345099:RNGP=1;

4. Reserve numbers 3874000..3874999 to be used as emergency servicesrouting keys. ESRK range index is 1 and ESRK prefix is 911.

WVC:ESRK=3874000&&3874999:EIDX=1,EPRE=911;

5. Reserve numbers 4991000..4993999 and 5011000..5012999 to be used asemergency services routing keys.

WVC:ESRK=4991000&&4993999&5011000&&5012999;

Additional information

The following list shows which parameters in the first block need parametersfrom the second block.



13 (66)


. handover number: type of number;

. mobile station roaming number: MSRN group;

. emergency services routing key <option>: ESRK range index <option>,ESRK prefix <option>;

Execution printouts

1. The execution printout of example 1 is the following:

HANDOVER NUMBER RANGE CREATED

FIRST NUMBER LAST NUMBER TON TOTAL

12345600 12345600 NATIONAL 1

UPDATING DISK AND DISTRIBUTING HRNFIL

COMMAND EXECUTED


ROAMING NUMBER RANGE CREATED

FIRST NUMBER LAST NUMBER RNGP TOTAL

44345800 44345859 0 60




44345900 44345979 0 80


COMMAND EXECUTED




12345000 12345099 1 100


COMMAND EXECUTED


EMERGENCY SERVICES ROUTING KEY RANGE CREATED

FIRST NUMBER LAST NUMBER INDEX PREFIX TOTAL




3874000 3874999 1 911 1000


COMMAND EXECUTED

The use of PREFIX (EPRE parameter) is optional.


EMERGENCY SERVICES ROUTING KEY RANGE CREATED


4991000 4993999 2 911 3000

5011000 5012999 3 911 2000


COMMAND EXECUTED


Semantic error messages

If an error occurs, the system outputs a general MML semantic error message.

Execution error messages

If an error occurs in TNAPRB, the system outputs the following header:

/*** MSRN HANDLING FAILURE IN TNAPRB:***/

An error occurred in TNAPRB. Check that the number of MSRN groups isbetween 0 and 50.

If the MSRN is already in the TNA, check with the WVJ:MSRN command whichMSRNs are already in use.

If the number of MSRNs in the TNA is more than 2000, use the WVJ:MSRNcommand to find out how many MSRNs there are.

After this message the system outputs information on TNAPRB in the form of anormal execution message.

The system may also output a general MML execution error message.



15 (66)





2 WVD: DELETE MSC NUMBER RANGEFunction

Use this command to delete the MSC number ranges created with the WVCcommand in the MSC.

Parameters

handover number,mobile station roaming number,emergency services routing key<option>;

Syntax

WVD:(HON=<handover number>... |

MSRN=<mobile station roaming number>... |

ESRK=<emergency services routing key><option>...);


handover number

HON= The starting point of the handover numberrange. The maximum length of thenumber is 18 digits. Grouping character'&' can be used. The last remaining rangecannot be deleted.


MSRN= The starting point of the roaming numberrange. The maximum length of thenumber is 18 digits. The roaming numbermust be in the international format with acountry code at the beginning of thenumber. Grouping character '&' can beused. The last remaining range cannot bedeleted.




17 (66)

WVD: DELETE MSC NUMBER RANGE

ESRK= The starting point of the emergencyservices routing key range. The ESRKnumber must have 7 digits. Groupingcharacter '&' can be used.

Examples

1. Delete handover number 12345600.

WVD:HON=12345600;

2. Delete roaming numbers 44345800..44345859 and 44345900..44345979.

WVD:MSRN=44345800&44345900;

3. Delete emergency services routing keys 3874000..3874999.

WVD:ESRK=3874000;

Execution printouts


HANDOVER NUMBERS


12345600 12345600 INTERNATIONAL 1

CONFIRM COMMAND EXECUTION Y/N ?

HANDOVER NUMBER RANGE DELETED


12345600 12345600 INTERNATIONAL 1


COMMAND EXECUTED


ROAMING NUMBERS


44345800 44345859 1 60


ROAMING NUMBER RANGE DELETED


44345800 44345859 1 60





ROAMING NUMBERS


44345900 44345979 1 80


ROAMING NUMBER RANGE DELETED


44345900 44345979 1 80


COMMAND EXECUTED


EMERGENCY SERVICES ROUTING KEYS


3874000 3874999 27 911 1000


EMERGENCY SERVICES ROUTING KEY RANGE DELETED


3874000 3874999 27 911 1000


COMMAND EXECUTED





/*** MSRN HANDLING FAILURE IN TNAPRB:***/

An error occured in TNAPRB. The MSRN does not match the one in TNA. If thefirst MSRN does not match the one sent by the command, use the WVJ:MSRNcommand to find out the starting MSRN.

After this message, the system outputs information on TNAPRB in the form of anormal execution message.



19 (66)

WVD: DELETE MSC NUMBER RANGE

/*** NUMBER DOES NOT EXIST ***/

You tried to delete the number which does not exist in the system. Check thenumber you typed in and repeat the command.





3 WVM: MODIFY MSC NUMBER RANGEFunction

Use this command to modify the MSC number ranges created with the WVCcommand in the MSC.

Parameters

handover number,mobile station roaming number,emergency services routing key<option>,handover type of number:

new range:

new ESRK prefix <option>;

Syntax

WVM:(HON=<handover number> |

MSRN=<mobile station roaming number> |

HTON=<handover type of number> |

ESRK=<emergency services routing key> <option>):

<new range...>:

[NEPRE=<new ESRK prefix> <option>];


handover number

HON= The starting point of the handover numberrange which is to be modified. Themaximum length of the number is 18digits.


MSRN= The starting point of the roaming numberrange which is to be modified. Themaximum length of the number is 18digits. The MSRN number must start withyour own country code.



21 (66)

WVM: MODIFY MSC NUMBER RANGE

handover type of numberThe type of all handover numbers in the HRNFIL. If you givethis parameter, a new range cannot be specified.

Table 2. Values for HTON parameter in WVM command


HTON= NAT in national format



ESRK= The starting point of the emergencyservices routing key range which is to bemodified. The ESRK number must have 7digits.

new range The starting and ending points of the modified number rangeare separated with the '&&' signs. In the case of HON orMSRN the maximum length of the number is 18 digits, but inthe case of ESRK the starting and ending numbers must have7 digits. Both numbers must have the same amount of digits.

If the mobile roaming number range is given, the last digit ofthe starting number must be 0, and the last digit of the endingnumber must be 9. The first digits must contain your owncountry code. The amount of numbers in a given range cannotexceed the limit mentioned in the WVC command .

If the HTON parameter is given, do not give a new range.

new ESRK prefix <option>

NEPRE= The ESRK prefix can be given only if theemergency services routing key parameteris given in the first parameter block. TheESRK prefix can have values from 0 to999 or NONE. The default is the oldvalue.




Examples

1. Reserve number 12345700 instead of number 12345600 to be used as ahandover number.

WVM:HON=12345600:12345700;

2. Reserve numbers 44346000..44346059 instead of numbers44345800..44345859 to be used as roaming numbers.

WVM:MSRN=44345800:44346000&&44346059;

3. Change the type of all handover numbers to the national format.

WVM:HTON=NAT;

4. Reserve numbers 3871000..3871999 instead of numbers3874000..3874999 to be used as emergency services routing keys. ModifyESRK prefix to value 112 <option>.

WVM:ESRK=3874000:3871000&&3871999:NEPRE=112;

Execution printouts


HANDOVER NUMBER RANGE MODIFIED

OLD VALUE FIRST NUMBER LAST NUMBER

TOTAL

12345600 12345600 1

NEW VALUE FIRST NUMBER LAST NUMBER

TOTAL

12345700 12345700 1


COMMAND EXECUTED


ROAMING NUMBER RANGE MODIFIED

OLD RANGE


44345800 44345859 0 60

NEW RANGE


44346000 44346059 0 60



23 (66)



COMMAND EXECUTED


HANDOVER TYPE OF NUMBER MODIFIED

OLD TYPE OF NUMBER VALUE

HANDOVER NUMBERS


12345700 12345700 INTERNATIONAL 1

------------

TOTAL 1

NEW TYPE OF NUMBER VALUE

HANDOVER NUMBERS


12345700 12345700 NATIONAL 1

------------

TOTAL 1


COMMAND EXECUTED


EMERGENCY SERVICES ROUTING KEY RANGE MODIFIED

OLD RANGE

FIRST NUMBER LAST NUMBER INDEX PREFIX

TOTAL

3874000 3874999 16 911 1000

NEW RANGE

FIRST NUMBER LAST NUMBER INDEX PREFIX

TOTAL

3871000 3871999 16 112 1000


COMMAND EXECUTED








If an error occurs in TNAPRB, the system outputs the following header:

/*** MSRN HANDLING FAILURE IN TNAPRB: ***/

An error occurred in TNAPRB.

Check with the WVJ:MSRN command that

. the number of MSRN groups is between 0 and 50

. there are not more than 2000 MSRNs allocated at a time.

After this message, the system outputs information on TNAPRB in the form of anormal execution message.




25 (66)





4 WVJ: INTERROGATE MSC NUMBERRANGE

Function

Use this command to interrogate the MSC number ranges created with the WVCcommand in the MSC.

Parameters

MSC number range name

Syntax

WVJ:[HON |

MSRN |

ESRK<option>]

[<all> def]];


MSC number range nameThe parameter can have one of the following values:

HON interrogate handover number range

MSRN interrogate mobile station roamingnumber range

ESRK interrogate emergency services routingkey range <option>

all interrogate all MSC number ranges.

Examples

1. Interrogate all MSC number ranges.

WVJ;



27 (66)

WVJ: INTERROGATE MSC NUMBER RANGE

2. Interrogate the handover number range.

WVJ:HON;

3. Interrogate the mobile roaming number range.

WVJ:MSRN;

4. Interrogate the emergency services routing key range.

WVJ:ESRK;

Execution printouts

1. If the emergency services routing key option is off, the execution printoutof example 1 is the following :

HANDOVER NUMBERS


12345000 12345099 INTERNATIONAL 100

12345050 12345069 INTERNATIONAL 20

12346000 12346049 INTERNATIONAL 50

------------

TOTAL 170

ROAMING NUMBERS


44345800 44345859 0 60

44345900 44345979 1 80

------------

TOTAL 140

COMMAND EXECUTED

If there are no number ranges, the printout is the following:

HANDOVER NUMBERS


------------

TOTAL 0

ROAMING NUMBERS


------------

TOTAL 0




COMMAND EXECUTED


HANDOVER NUMBERS


12345000 12345099 INTERNATIONAL 100

12345050 12345069 INTERNATIONAL 20

12346000 12346049 INTERNATIONAL 50

------------

TOTAL 170

COMMAND EXECUTED


ROAMING NUMBERS


44345800 44345859 0 60

44345900 44345979 1 80

------------

TOTAL 140

COMMAND EXECUTED


EMERGENCY SERVICES ROUTING KEYS


3804000 3804999 1 911 1000

4140000 4169999 2 911 30000

------------

TOTAL 31000

COMMAND EXECUTED





If an error occurs, the system outputs a general MML execution error message.



29 (66)

WVJ: INTERROGATE MSC NUMBER RANGE




5 WVS: CREATE NETWORK ANDNETWORK ELEMENT SPECIFICNUMBER

Function

Use this command to create network element specific numbers.

Parameters

mobile country code,mobile network code,EIR number,MSC number,VLRnumber,default calling line identity,HLR number,operator service number IMSI<option>,national operator prefix <option>,international operator prefix<option>,one digit carrier identification code prefix <option>,two digit carrieridentification code prefix <option>,three digit carrier identification code prefix<option>,four digit carrier identification code prefix <option>,PLMN defaultcharging area number <option>,extra call forwarding number <option>,GMLCaddress for emergency services <option>,call forwarding number withnotification <option>,SMSC address for welcome SM <option>,SMSCapplication address<option>,configurable MSISDN number <option>,corenetwork node identifier <option>,SMSC address for trigger SM <option>,SMSCapplication address for trigger SM <option>,common MSISDN number fortrigger SM <option>:

numbering plan,type of number,A notification <option>,B notification <option>;

Syntax

The syntax for the MSC and the HLR is slightly different. The first syntax is forthe MSC and the second is for the HLR.

WVS: (MCC=<mobile country code> |

MNC=<mobile network code>|

EIR=<EIR number> |

CLI=<default calling line identity> |

MSC=<MSC number> |

VLR=<VLR number>|

OSN=<operator service number IMSI><option> |

NOPP=<national operator prefix><option> |



31 (66)

WVS: CREATE NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

IOPP=<international operator prefix><option> |

CIC3P=<three digit CIC prefix><option> |

CIC4P=<four digit CIC prefix><option> |

DEFCA=<PLMN default charging area><option> |

EXCF=<EXCF number><option> |

ESGMLC=<GMLC address for emergency services><option> |

SCADDR=<SMSC address for welcome SM><option> |

WSCAPP=<SMSC application address><option> |

CMSISDN=<configurable MSISDN number><option> |

CNID=<core network node identifier><option> |

TRIGSC=<SMSC address for trigger SM><option> |

TRIGAC=<SMSC application address for trigger SM><option> |

TMSISDN=<common MSISDN number for trigger SM><option> ):

[NP=<numbering plan>|

TON=<type of number>]...;

WVS: (MCC=<mobile country code> |


EIR=<EIR number> |

HLR=<HLR number>|




CIC1P=<one digit CIC prefix><option> |

CIC2P=<two digit CIC prefix><option> |



CFNWN=<call forwarding number with notification><option> |



CMSISDN=<Configurable MSISDN number><option>):

[NP=<numbering plan> |

TON=<type of number> |

AN=<A notification><option> |

BN=<B notification><option>]...;


Note that the parameters for the MSC and the HLR are slightly different.

mobile country code

MCC= A part of the mobile station identification,identifying uniquely the home country ofthe station. The maximum length of thecode is 3 digits.

mobile network code




MNC= A digit or combination of digits in thenational part of the mobile stationidentification, identifying uniquely thehome PLMN of the mobile station. Themaximum length of the code is 3 digits.

EIR number

EIR= The number of the Equipment IdentityRegister. There can be several EIRnumbers with several types of numbersand numbering plan values. When yougive the EIR number, give both thenumbering plan and the type of number inthe second parameter block. Themaximum length of the number is 18digits.

MSC number

MSC= The number of the mobile servicesswitching centre. There can be severalMSC numbers with several numberingplan values. In the international format thefirst digits of the number must contain thecountry code. When you give the MSCnumber, give also the numbering plan inthe second parameter block. Themaximum length of the number is 18digits.

VLR number

VLR= The number of the visitor locationregister. The number must be in the E.164international format and therefore the firstdigits of the number must contain thecountry code. The maximum length of thenumber is 18 digits.

default calling line identity

CLI= In the international format the first digitsof the default calling line identity mustcontain the country code. When you givethe default calling line identity, give alsothe type of number (TON) in the second



33 (66)


parameter block. Give only 1 CLI perTON. Where zero length CLI is required,set the CLI to FF, otherwise the maximumlength is 18 digits.

HLR number

HLR= The number of the home location register.The number must be in the E.164international format and therefore the firstdigits of the number must contain thecountry code. The maximum length of thenumber is 18 digits.

operator service number IMSI <option>

OSN= The IMSI for the operator service number.This is an optional parameter. Themaximum length of the number is 18digits.

national operator prefix <option>

NOPP= The national operator prefix is an optionalparameter. The minimum value is 0, andthe maximum value is 9.

international operator prefix <option>

IOPP= The international operator prefix is anoptional parameter. The minimum value is00, and the maximum value is 99.

one digit CIC prefix <option>

CIC1P= The prefix of the carrier identificationcode. Use this parameter when the carrieridentification code is 1digit long. This isan optional parameter. The possible valueof the parameter is 1�3 decimal digits.

two digit CIC prefix <option>

CIC2P= The prefix of the carrier identificationcode. Use this parameter when the carrieridentification code is 2 digits long. This isan optional parameter. The possible valueof the parameter is 1�3 decimal digits.




three digit CIC prefix <option>


four digit CIC prefix <option>


PLMN default charging area <option>

DEFCA= The PLMN default charging area can havevalues ranging from 0001 to 9999. This isan optional parameter.

extra call forwarding number <option>

EXCF= The extra call forwarding number is setautomatically to the international formatand numbering plan (E.164) and thereforethe first digits of the number must containthe country code. This is an optionalparameter. There can be several extra callforwarding numbers. The maximumlength of the number is 18 digits.

GMLC address for emergency services <option>

ESGMLC= The address of the Gateway MobileLocation Center which handlesemergency positioning related issues foran MSC. The address has to be given inthe international format E.164 andtherefore the first digits of the addressmust contain the country code. This is anoptional parameter. The maximum lengthof the address is 18 digits.

call forwarding number with notification <option>



35 (66)


CFNWN= The number which causes the specialnotification handling when a call isforwarded. This is an optional parameter.CFNWN can be from 1 to 18 digits long.There can be five CFNWNs in HRNFIL.

SMSC address for welcome SM <option>

SCADDR= Identify uniquely SMSC address forwelcome SM. When SCADDR is given,give the numbering plan and the type ofnumber in the second parameter block.The maximum length of the number is 18digits.

SMSC application address <option>

WSCAPP= Identify uniquely SMSC applicationaddress for welcome SM. WhenWSCAPP is given, give the numberingplan and the type of number in the secondparameter block. The maximum length ofthe number is 18 digits.

configurable MSISDN number <option>

CMSISDN= Identify uniquely CMSISDN for welcomeSM. When CMSISDN is given, give thenumbering plan and the type of number inthe second parameter block. Themaximum length of the number is 18digits.

core network node identifier <option>

CNID= Identifier of core network node in the 3Gnetwork. Core network node means thesame as the MSC in the 2G network. Thevalue of the identifier is 0�4095. There isno default value for CNID.

SMSC address for trigger SM <option>




TRIGSC= Identify uniquely SMSC address fortrigger SM. When TRIGSC is given, givethe numbering plan and the type ofnumber in the second parameter block.The maximum length of the number is 18digits.

SMSC application address for trigger SM <option>

TRIGAC= Identify uniquely SMSC applicationaddress for trigger SM. When TRIGAC isgiven, give the numbering plan and thetype of number in the second parameterblock. The maximum length of thenumber is 18 digits.

Common MSISDN number for trigger SM <option>

TMSISDN= Identify uniquely the sender of the triggerSM. When TMSISDN is given, give thenumbering plan and the type of number inthe second parameter block. Themaximum length of the number is 18digits.

numbering plan

NP= The code which refers to the standardisednumbering instruction described by theITU-T (formerly CCITT). The possiblevalues are E164, X121, TELEX,NATSTD, PRIVATE, and UNKNOWN.

type of number

Table 3. Values for TON parameter in WVS command




Give this parameter in the second parameter block when yougive the EIR, SCADDR, WSCAPP, CMSISDN, or CLIparameters in the first parameter block.



37 (66)


A notification <option>

Table 4. Values for AN parameter in WVS command


AN= Y notification to A-subscriber

N no notification to A-subscriber

DEF notification to A-subscriber as provisioned (default)

Use this parameter in the second parameter block when yougive the CFNWN parameter in the first parameter block.

B notification <option>

Table 5. Values for BN parameter in WVS command


BN= Y notification to B-subscriber

N no notification to B-subscriber

DEF notification to B-subscriber as provisioned (default)

Use this parameter in the second parameter block when theCFNWN parameter is given in the first parameter block.

Examples

Note that the examples 4, 5, 6, 7, 16, 17, 23, 24, 25 and 26 are only for the MSCand the examples 8 and 15 are only for the HLR.

1. Create mobile country code 012.

WVS:MCC=012;

2. Create mobile network code 23.

WVS:MNC=23;

3. Create Equipment Identity Register number 123456 to numbering planE164 in national format.




WVS:EIR=123456:NP=E164,TON=NAT;

4. Create default calling line identity 358000000 to international format.

WVS:CLI=358000000:TON=INT;

5. Create zero length default calling line identity to national format.

WVS:CLI=FF:TON=NAT;

6. Create the MSC number 123456 to numbering plan TELEX.

WVS:MSC=123456:NP=TELEX;

7. Create the VLR number 234657.

WVS:VLR=234657;

8. Create the HLR number 123456.

WVS:HLR=123456;

9. Create operator service number IMSI 123 <option>.

WVS:OSN=123;

10. Create National Operator Prefix 1 <option>

WVS:NOPP=1;

11. Create International Operator Prefix 10 <option>.

WVS:IOPP=10;

12. Create One Digit CIC Prefix 999 <option>.

WVS:CIC1P=999;

13. Create Two Digit CIC Prefix 2 <option>.

WVS:CIC2P=2;

14. Create Three Digit CIC Prefix 01 <option>.

WVS:CIC3P=10;

15. Create Four Digit CIC Prefix 111 <option>.

WVS:CIC4P=101;

16. Create PLMN default charging area 0200 <option>.

WVS:DEFCA=0200;

17. Create call forwarding number 123456, which causes the specialnotification handling.



39 (66)


WVS:CFNWN=123456:AN=Y,BN=N;

18. Create extra call forwarding number 123 <option>.

WVS:EXCF=123;

19. Create GMLC address for emergency services 112233 <option>.

WVS:ESGMLC=112233;

20. Create SMSC address 123456 to numbering plan E164 in national format<option>.

WVS:SCADDR=123456:NP=E164,TON=NAT;

21. Create SMSC application address 123456 to numbering plan E164 innational format <option>.

WVS:WSCAPP=123456:NP=E164,TON=NAT;

22. Create configurable MSISDN number 123456 to numbering plan E164 innational format <option>.

WVS:CMSISDN=123456:NP=E164,TON=NAT;

23. Create core network node identifier 1234 <option>.

WVS:CNID=1234;

24. Create SMSC address for trigger SM 123456 to numbering plan E164 innational format <option>.

WVS:TRIGSC=123456:NP=E164,TON=NAT;

25. Create SMSC application address for trigger SM 123456 to numberingplan E164 in national format <option>.

WVS:TRIGAC=123456:NP=E164,TON=NAT;

26. Create common MSISDN number for trigger SM 123456 to numberingplan E164 in national format <option>.

WVS:TMSISDN=123456:NP=E164,TON=NAT;


The following list shows which parameters in the first block need parametersfrom the second block. When a parameter is indicated it does not need parametersfrom the second block. Note that the parameters for the MSC and the HLR differslightly from each other.

. Mobile country code;

. Mobile network code;




. EIR number: numbering plan, type of number;

. Default calling line identity : type of number;

. MSC: numbering plan;

. VLR number;

. HLR number;

. Operator service number IMSI <option>;

. National operator prefix <option>;

. International operator prefix <option>;

. One digit carrier identification code prefix <option>;

. Two-digit carrier identification code prefix <option>;

. Three-digit carrier identification code prefix <option>;

. Four-digit carrier identification code prefix <option>;

. PLMN default charging area <option>;

. Call forwarding number with notification <option>: A notification, Bnotification;

. Extra call forwarding number <option>;

. GMLC address for emergency services <option>;

. SMSC address for welcome SM <option>: numbering plan, type ofnumber;

. SMSC application address <option>: numbering plan, type of number;

. Configurable MSISDN number <option>: numbering plan, type ofnumber;

. Core network node identifier <option>;

. SMSC address for trigger SM <option>: numbering plan, type of number;

. SMSC application address for trigger SM <option>: numbering plan, typeof number;

. Common MSISDN number for trigger SM <option>: numbering plan, typeof number;



41 (66)


Execution printouts

1. The execution printout of example 1 (WVS:MCC=012; ) is the following:

CREATING MOBILE COUNTRY CODE

012


COMMAND EXECUTED

2. The execution printout of example 2 (WVS:MNC=23; ) is the following:

CREATING MOBILE NETWORK CODE

23


COMMAND EXECUTED

3. The execution printout of example 3 (WVS:EIR=123456:NP=E164,TON=NAT; ) is the following:

CREATING EIR NUMBER

NUMBER NP TON

123456 E.164 NATIONAL


COMMAND EXECUTED








6 WVR: DELETE NETWORK ANDNETWORK ELEMENT SPECIFICNUMBER

Function

Use this command to delete network and network element specific numbers.

Parameters

EIR number,MSC number,PLMN default charging area number <option>,extracall forwarding number <option>,GMLC address for emergency services<option>,call forwarding number with notification <option>,SMSC address forwelcome SM <option>,SMSC application address <option>,configurableMSISDN number <option>,core network node identifier <option>,SMSC addressfor trigger SM <option>,SMSC application address for trigger SM <option>,common MSISDN number for trigger SM <option>:

numbering plan,type of number;

Syntax


WVR: (EIR=<EIR number> |

MSC=<MSC number>|



ESGMLC=<GMLC address for emergency services><option>|



CMSISDN=<configurable MSISDN number><option> |









43 (66)

WVR: DELETE NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

WVR: (EIR=<EIR number> |

CFNWN=<call forwarding number with notification><option> |



CMSISDN=<Configurable MSISDN number><option>):





EIR number


MSC number













SMSC address for welcome SM <option>

SCADDR= Define SMSC address for welcome SM.When SCADDR is given, give also thenumbering plan and the type of number inthe second parameter block. Themaximum length of the number is 18digits.

SMSC application address <option>

WSCAPP= Define SMSC application address forwelcome SM. When WSCAPP is given,give also the numbering plan and the typeof number in the second parameter. Themaximum length of the number is 18digits.

configurable MSISDN number <option>



45 (66)


CMSISDN= Define CMSISDN for welcome SM.When CMSISDN is given, give also thenumbering plan and the type of number inthe second parameter block. Themaximum length of the number is 18digits.









numbering plan




NP= The code which refers to the standardisednumbering instruction described by theITU-T (formerly CCITT). Give thisparameter in the second parameter blockwhen you give the EIR, SCADDR,WSCAPP, CMSISDN, or MSCparameters in the first parameter block.The possible values are E164, X121,TELEX, NATSTD, PRIVATE, andUNKNOWN.

type of number

Table 6. Values for TON parameter in WVR command




Give this parameter in the second parameter block when yougive parameter EIR, SCADDR, WSCAPP, or CMSISDN inthe first parameter block.


The following list shows which parameters in the first block need parametersfrom the second block. Note that the parameters for the MSC and the HLR differslightly from each other.

. EIR number : numbering plan, type of number;

Execution printouts

1. The execution printout of example 1 (WVR:EIR=123456:NP=E164,TON=NAT; ) is the following:

DELETING EIR NUMBER

NUMBER NP TON



COMMAND EXECUTED



47 (66)


2. The execution printout of example 7 (WVR:SCADDR=123456:NP=E164,TON=NAT; ) is the following:

DELETING SMSC ADDRESS FOR WELCOME SM

NUMBER NP TON



COMMAND EXECUTED

3. The execution printout of example 8 (WVR:WSCAPP=123456:NP=E164,TON=NAT; ) is the following:

DELETING SMSC APPLICATION ADDRESS

NUMBER NP TON



COMMAND EXECUTED








7 WVF: MODIFY NETWORK ANDNETWORK ELEMENT SPECIFICNUMBER

Function

Use this command to modify network element specific numbers. Note that onlynumber values are allowed to be modified.

Parameters

mobile country code,mobile network code,EIR number,MSC number,VLRnumber,default calling line identity,HLR number,operator service number IMSI<option>,national operator prefix <option>,international operator prefix<option>,one digit carrier identification code prefix <option>,two digit carrieridentification code prefix <option>,three digit carrier identification code prefix<option>,four digit carrier identification code prefix <option>,call forwardingnumber with notification <option>,core network node identifier <option>,SMSCaddress for trigger SM <option>,SMSC application address for trigger SM<option>,common MSISDN number for trigger SM <option>:

new value:

numbering plan,type of number;

Syntax


WVF: (MCC=<mobile country code> |


EIR=<EIR number> |

CLI=<default calling line identity> |

MSC=<MSC number> |

VLR=<VLR number>|






49 (66)

WVF: MODIFY NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER





ESGMLC=<GMLC address for emergency services><option> |





<new value>:



WVF: (MCC=<mobile country code> |


EIR=<EIR number> |

HLR=<HLR number>|




CIC1P=<one digit CIC prefix><option> |

CIC2P=<two digit CIC prefix><option> |



CFNWN=<call forwarding number with notification><option>):

<new value>:





mobile country code

MCC= A part of the mobile station identification,identifying uniquely the home country ofthe station. The maximum length of thecode is 3 digits.

mobile network code

MNC= A digit or combination of digits in thenational part of the mobile stationidentification, identifying uniquely thehome PLMN of the mobile station. Themaximum length of the code is 3 digits.




EIR number


MSC number


VLR number

VLR= The number of the visitor locationregister. The number must be in the E.164international format and therefore the firstdigits of the number must contain thecountry code. The maximum length of thenumber is 18 digits.

default calling line identity

CLI= In the international format, the first digitsof the default calling line identity mustcontain the country code. When you givethe default calling line identity, give alsothe type of number (TON) in the secondparameter block. Give only 1 CLI perTON. Where zero length CLI is required,set the CLI to FF, otherwise the maximumlength is 18 digits.

HLR number



51 (66)


HLR= The number of the home location register.The number must be in the E.164international format and therefore the firstdigits of the number must contain thecountry code. The maximum length of thenumber is 18 digits.

operator service number IMSI <option>

OSN= The IMSI for the operator service number.This is an optional parameter. Themaximum length of the number is 18digits.

national operator prefix <option>

NOPP= The national operator prefix is an optionalparameter. The minimum value is 0, andthe maximum value is 9.

international operator prefix <option>

IOPP= The international operator prefix is anoptional parameter. The minimum value is00, and the maximum value is 99.

one digit CIC prefix <option>

CIC1P= The prefix of the carrier identificationcode. Use this parameter when the carrieridentification code is 1 digit long. This isan optional parameter. The possible valueof the parameter is 1�3 decimal digits.

two-digit CIC prefix <option>


three-digit CIC prefix <option>





four-digit CIC prefix <option>











53 (66)











new value The new value of the network and network element specificnumber, which is the result of the modification command.

numbering plan




NP= The code which refers to the standardisednumbering instruction described by theITU-T (formerly CCITT). Give thisparameter in the second parameter blockwhen you give the EIR or MSCparameters in the first parameter block.The possible values are E164, X121,TELEX, NATSTD, PRIVATE, andUNKNOWN.

type of number

Table 7. Values for TON parameter in WVF command




Give this parameter in the second parameter block when yougive the EIR or CLI parameters in the first parameter block.

Examples

Note that the examples 4, 5, 6, 7, 16, 17, 19, 20, 21, 22 and 23 are only for theMSC and the examples 8, 14, 15 and 18 are only for the HLR.

1. Modify mobile country code 012 to 013.

WVF:MCC=012:013;

2. Modify mobile network code 23 to 24.

WVF:MNC=23:24;

3. Modify Equipment Identity Register number 123456 to 123457 innumbering plan E.164 in national format.

WVF:EIR=123456:123457:NP=E164,TON=NAT;

4. Modify default calling line identity 358000000 to 358000001 ininternational format.

WVF:CLI=358000000:358000001:TON=INT;

5. Modify the zero length default calling line identity to 123 which is in thenational format.



55 (66)


WVF:CLI=FF:123:TON=NAT;

6. Modify the MSC number 123456 to 123457 in numbering plan TELEX.

WVF:MSC=123456:123457:NP=TELEX;

7. Modify the VLR number 123456 to 123457.

WVF:VLR=123456:123457;

8. Modify the HLR number 123456 to 123457.

WVF:HLR=123456:123457;

9. Modify operator service number IMSI 123 to 124 <option>.

WVF:OSN=123:124;

10. Modify National Operator Prefix 1 to 2 <option>.

WVF:NOPP=1:2;

11. Modify International Operator Prefix 10 to 11 <option>.

WVF:IOPP=10:11;

12. Modify One Digit CIC Prefix 999 to 1 <option>.

WVF:CIC1P=999:1;

13. Modify Two-Digit CIC Prefix 1 to 999 <option>.

WVF:CIC2P=1:999;

14. Modify Three-Digit CIC Prefix 01 to 02 <option>.

WVF:CIC3P=01:02;

15. Modify Four-Digit CIC Prefix 111 to 112 <option>.

WVF:CIC4P=111:112;

16. Modify PLMN default charging area 0200 to 0201 <option>.

WVF:DEFCA=0200:0201;

17. Modify extra call forwarding number 123 to 124 <option>.

WVF:EXCF=123:124;

18. Modify call forwarding number 123456, which causes the specialnotification handling, to 123457.

WVF:CFNWN=123456:123457;

19. Modify GMLC address for emergency services 112233 to 112244<option>.




WVF:ESGMLC=112233:112244;

20. Modify core network node identifier 1234 to 1235 <option>.

WVF:CNID=1234:1235;

21. Modify SMSC address for trigger SM 123456 with numbering plan E164in national format to 1234567 <option>.

WVF:TRIGSC=123456:1234567:NP=E164,TON=NAT;

22. Modify SMSC application address for trigger SM 123456 with numberingplan E.164 in national format to 1234567 <option>.

WVF:TRIGAC=123456:1234567:NP=E164,TON=NAT;

23. Modify common MSISDN number for trigger SM 123456 with numberingplan E.164 in national format to 1234567 <option>.

WVF:TMSISDN=123456:1234567:NP=E164,TON=NAT;

Execution printouts

1. The execution printout of example 1 (WVF:MCC=012:013; ) is thefollowing:

MODIFYING MOBILE COUNTRY CODE

OLD VALUE

012

NEW VALUE

013


COMMAND EXECUTED

2. The execution printout of example 2 (WVF:MNC=23:24; ) is thefollowing:

MODIFYING MOBILE NETWORK CODE

OLD VALUE

23

NEW VALUE

24


COMMAND EXECUTED



57 (66)


3. The execution printout of example 3 (WVF:EIR=123456:123457:NP=E164,TON=NAT; ) is the following:

MODIFYING EIR NUMBER

OLD VALUE

NUMBER NP TON


NEW VALUE

NUMBER NP TON



COMMAND EXECUTED








8 WVI: INTERROGATE NETWORK ANDNETWORK ELEMENT SPECIFICNUMBER

Function

Use this command to interrogate network and network element specific numbers.This command has only one position defined parameter.

Parameters

interrogation type

Syntax


WVI: [[MCC |

MNC |

EIR |

CLI |

MSC |

VLR |

OSN <option> |

NOPP <option> |

IOPP <option>|

CIC3P <option> |

CIC4P <option>|

DEFCA <option> |

EXCF <option> |

ESGMLC <option> |

SCADDR <option> |

WSCAPP <option> |

CMSISDN <option> |

CNID <option> |

TRIGSC <option> |

TRIGAC <option> |

TMSISDN <option>]|

<all> def];



59 (66)

WVI: INTERROGATE NETWORK AND NETWORK ELEMENT SPECIFIC NUMBER

WVI: [[MCC |

MNC |

EIR |

HLR |

OSN <option> |

NOPP <option> |

IOPP <option>|

CIC1P <option> |

CIC2P <option>|

CIC3P <option> |

CIC4P <option>|

CFNWN <option> |

SCADDR <option> |

WSCAPP <option> |

CMSISDN <option>]|

<all> def];


Interrogation typeThe parameter can have one of the following values.

Note that the parameter values for the MSC and the HLR areslightly different.

MCC interrogate mobile country code

MNC interrogate mobile network code

EIR interrogate EIR number

MSC interrogate MSC number

VLR interrogate VLR number

CLI interrogate default calling line identity

HLR interrogate HLR number

OSN interrogate operator service number IMSI<option>

NOPP interrogate national operator prefix<option>

IOPP interrogate international operator prefix<option>




CIC1P interrogate one digit carrier identificationcode prefix <option>

CIC2P interrogate two-digit carrier identificationcode prefix <option>

CIC3P interrogate three-digit carrieridentification code prefix <option>

CIC4P interrogate four-digit carrier identificationcode prefix <option>

DEFCA interrogate PLMN default charging areanumber <option>

EXCF interrogate extra call forwarding number<option>

ESGMLC interrogate GMLC address for emergencyservices <option>

CFNWN interrogate call forwarding number withnotification <option>

SCADDR interrogate SMSC address <option>

WSCAPP interrogate SMSC application address<option>

CMSISDN interrogate configurable MSISDN number<option>

CNID interrogate core network node identifier<option>

TRIGSC interrogate SMSC address for trigger SM<option>

TRIGAC interrogate SMSC application address fortrigger SM <option>

TMSISDN interrogate common MSISDN number fortrigger SM <option>

all interrogate all MSC/HLR-specificnumbers.



61 (66)


Examples

1. Interrogate all network and network element specific numbers.

WVI;

2. Interrogate mobile country code.

WVI:MCC;

Execution printouts

1. If all options are on, the execution printout of example 1 (WVI; ) is thefollowing:


MOBILE COUNTRY CODE

012

MOBILE NETWORK CODE

012

EIR NUMBER

NUMBER NP TON

44123456 E.164 INTERNATIONAL


44123456 X.121 INTERNATIONAL

123456 X.121 NATIONAL

44123456 TELEX INTERNATIONAL

123456 TELEX NATIONAL

44123456 NATSTD INTERNATIONAL

123456 NATSTD NATIONAL

44123456 PRIVATE INTERNATIONAL

123456 PRIVATE NATIONAL

44123456 UNKNOWN INTERNATIONAL

123456 UNKNOWN NATIONAL

DEFAULT CALLING LINE IDENTITY

NUMBER NP TON


012 E.164 NATIONAL

MSC NUMBER




NUMBER NP TON


44013 X.121 INTERNATIONAL

44014 TELEX INTERNATIONAL

44015 NATSTD INTERNATIONAL

44016 PRIVATE INTERNATIONAL

44017 UNKNOWN INTERNATIONAL

VLR NUMBER

NUMBER NP TON


HLR NUMBER

NUMBER NP TON


OPERATOR SERVICE NUMBER IMSI

012

NATIONAL OPERATOR PREFIX

1

INTERNATIONAL OPERATOR PREFIX

02

ONE DIGIT CIC PREFIX

999

TWO DIGIT CIC PREFIX

1

THREE DIGIT CIC PREFIX

10

FOUR DIGIT CIC PREFIX



63 (66)


101

PLMN DEFAULT CHARGING AREA

0201

EXTRA CALL FORWARDING NUMBER

NUMBER NP TON





















GMLC ADDRESS FOR EMERGENCY SERVICES

NUMBER NP TON


CALL FORWARDING NUMBER WITH NOTIFICATION

NUMBER NP TON A NOTIFICATION B NOTIFICATION

44123451 E.164 INTERNATIONAL Y Y

44123452 E.164 INTERNATIONAL Y N

44123453 E.164 INTERNATIONAL N Y

44123454 E.164 INTERNATIONAL N N

44123455 E.164 INTERNATIONAL DEF DEF

SMSC ADDRESS FOR WELCOME SM




NUMBER NP TON


SMSC APPLICATION ADDRESS

NUMBER NP TON


CONFIGURABLE MSISDN NUMBER

NUMBER NP TON


CORE NETWORK NODE IDENTIFIER

1234

SMSC ADDRESS FOR TRIGGER SM

NUMBER NP TON


SMSC APPLICATION ADDRESS FOR TRIGGER SM

NUMBER NP TON


COMMON MSISDN NUMBER FOR TRIGGER SM

NUMBER NP TON


COMMAND EXECUTED

2. The execution printout of example 2 (WVI:MCC; ) is the following:

MOBILE COUNTRY CODE

012

COMMAND EXECUTED



65 (66)









Documents

Dn0114587 5 en Global PDF Online a4