D/N VARI-FOCAL IR CAMERA - VERROCCHIOPRECAUTIONS Do not drop or strike this equipment. Do not install the equipment near any naked flames or heat sources. Do not expose this unit to

INSTRUCTION MANUAL

66-CMR22CSE

MERIT LILIN ENT. CO., LTDhttp://www.meritlilin.com

D/N VARI-FOCAL IR CAMERACMR224X/228X/254X/258X3.6

CMR224X/228X/254X/258X2.2

PRECAUTIONS

Do not drop or strike this equipment.

Do not install the equipment near any naked flames or heat sources.

Do not expose this unit to rain , moisture , smoke or dust environment.

Do not cover the opening of the cabinet with cloth and plastic or to install this unit

in poor ventilated places. Allow 10cm between this unit and its surroundings.

Do not continue to operate the unit under abnormal conditions such as detection

of smoke, strange smell or no display on screen while power is turned on.

Do not touch the power connection with wet hands.

Do not damage the power cord or leave it under pressure.

Do not operate this unit near magnet, speaker system, etc., to avoid unnecessary

magnetic interference.

Do not drop metallic parts through slots.

Connection cables should be grounded properly.

It will cause damage to the equipment.

The presents of flammable gas or object in the operating environment or exposing this

unit to direct sunlight may cause fire and severe injury.

May cause short circuit, fire and serious damage to this unit.

Unplug this unit and have it checked by qualified service personnel.

May cause overheat. The normal operating temperature is 0 C ~ 40 C.

Contact qualified service personnel for help.

May cause short circuit or electric shock.

May cause fire or shock hazard.

These interference will cause color confusion and screen fluctuation.

This could permanently damage the appliance.

Sudden surge such as lightening will damage the system permanently.

CAUTION

RISK OF ELECTRIC SHOCK

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT OPEN COVER.

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of uninsulated "dangerous voltage" within theproduct's enclosure that may be of sufficient magnitude

The exclamation point within an equilateral triangle isintended to alert the user to the presence of importantoperating and maintenance (servicing) instructions in

to constitute a risk of electric shock to persons.

the literature accompanying the unit.

Part Description & Dimension

SUN SHIELD

FRONT FIXED RING

REAR FIXED RING

BASE

WINDOW

FRONT COVER

FOCUS & ZOOM ADJUSTMENT SCREW

REAR COVER

AUXILIARY BASE

1

Unit: mm

224

250

103

83.5

6.553

65

65

65 65

1. First, take out the auxiliary base(FIG.1), and take power cable and video cable through

auxiliary base. Then, fix the auxiliary base on any position you want(FIG.2&FIG.3). If you

don't need to use the auxiliary base, please skip this step.

FIG. 3

1-1. It can adjust angle range on vertical(FIG.4) and horizontal(FIG.5) direction without

using auxiliary base.

FIG. 4 FIG. 5

FIG. 2

2

FIG. 1

Installation

88

42

88

42

88

42

88

42

FIG. 6

1-2. It can adjust angle range on vertical(FIG.6&FIG.7) and horizontal(FIG.8&FIG.9)

direction with auxiliary base.

FIG. 7 FIG. 9

2. Take the camera body, and take out the green receptacle for backup(FIG.10). Then, take

out two red receptacles, too. Right now, put the two red receptacles on the "Live" and

"Neutral", and put the green receptacle on the "Earth"(FIG.11).

FIG. 10

Green Receptacle

FIG. 11

3

FIG. 8

Earth(Green)

Neutral(Red)

Live(Red)

3. To plug in the red plug of brown(black) wire with the red receptacle of "Live". To plug in the

red plug of blue (white) wire with the red receptacle of "Neutral". To plug in the green plug

of yellow/green (green) wire with the green receptacle of "Earth". To plug in video output

with video cable(FIG.12). Also for the security, please use the adhesive tape to wrap the

connections of four wires(FIG.13).

FIG. 13

Earth

FIG. 12

Neutral

Live

Yellow/Green(Green)

Blue(White)

Brown(Black)

Video Output Video Cable

4. Take the screws, and use it to fix the camera body on the auxiliary base or on any position

you want (FIG.14&FIG.15).

FIG. 14 FIG. 15

4

If used power cable is like two wire combine, please put them separately on

"Live" and "Neutral".

Notice

Green Plug

Red Plug

Red Plug

Green Receptacle

Red Receptacle

Red Receptacle

Video Output

Earth

Neutral

Live

Video Cable

Yellow/Green(Green)

Blue(White)

Brown(Black)

NW

T

5. Using the screw driver to insert socket, and loosen the front and rear fix ring of the bracket.

Also, move the camera body to the desired angle, and then tighten the front and rear fixed

ring (FIG.16).

FIG. 16

5

6. Using the screw driver to adjust zoom & focus of lens for image of video (FIG.17).

FIG. 17

Zoom

Focus

Tighten

Loosen

Loosen

Tighten

INOUT

NOTES

1. The camera built-in the IRIS LEVEL VR and switch for indoor image(IN) / outdoor image

(OUT).

If want to adjust two functions as above, first please take out the sun shield, and then take

out the screws of front cover and rear cover(FIG.18). Once it's done for adjustment, please

tighten those screws again(FIG.19).

6

FIG. 18 FIG. 19

2. Switch of IN/OUT

Initial setting is on "OUT" position.

IN: To push the switch on right side for using on indoor function. The color rolling

phenomenon won't be occured. If using this function on outdoor, the image contrast

and sharpness are not good or black and white image will be occured.

OUT: To push the switch on left side for using on outdoor function. The image contrast and

sharpness will be good. If using this function on indoor, the color rolling phenomenon

will be occured.

3. IRIS LEVEL VR(FIG.20)

To turn the VR clockwise for increasing brightness of image. To turn the VR counter-

clockwise for decreasing brightness of image.

FIG. 20

IRIS LEVEL

VR

Switch of IN/OUT

7

Specifications

Model No.

Lens

Power Input Vol tage

System

Sync. Mode

Pick Up Element

Effect ive Pixe ls

Chip Size

Hor izonta l & Ver t ica l

Sync. Frequency

Scanning System

Inf rared Cut Fi l ter

Resolut ion

Min imum I l luminat ion

S/N Rat io

Auto Gain Contro l

Whi te Balance

Aper ture Correct ion

Power Consumpt ion

Back Light Compensat ion

Video Output

Operat ing Temperature

Gamma Character is t ic

IP Rat ing

Inf rared

LEDBeam Spread

Peak Wavelength

Radiant Dis tance

Dimension

Weight

Focal Length

I r is

Angle of v iew

H

V

D

CMR224X3.6

4 ~ 9mm

F1.6

NTSC or PAL

AC24V ( 10%)

Interna l

1 /3" Exv iew HAD CCD Sensor

510(H) x 492(V) [NTSC]

500(H) x 582(V) [PAL]

6.00mm(H) x 4.96mm(V)

15.734 KHz / 59.94Hz [NTSC]

15.625 KHz / 50Hz [PAL]

2:1 Inter lace

0 Lux With IR ON

Auto Selectable, Automatic Switch

From Color Mode To Monochrome

Color : 380TV Lines , Mono: 450TV Lines

Color : 0 .02Lux at F1.4

Mono: 0.005Lux at F1.4

More Then 50dB (AGC-OFF)

36dB Var iab le Gain

ATW

Hor izonta l , Ver t ica l

7 .2W

Auto

CVBS 1.0Vp-p, 75ohm

IP68

850nm

30

35M

-10 ~ +50 (14 ~ 122 )

118mm(W) x 103mm(H) x 250mm(D)

730g

=0.45

CMR228X3.6 CMR224X2.2 CMR228X2.2

Design and speci f icat ions are subject to change wi thout not ice.

D/N STANDARD RESOLUTION VARI-FOCAL IR CAMERA

AC100~240V

Window 79 Heat Resistant Glass

3.3 ~ 12mm

F1.4

89.8 ~ 23.9 69 ~ 30.7

63.6 ~ 17.9 51 ~ 23

125.7 ~ 29.9 86 ~ 38.5

AC24V ( 10%) AC100~240V



8

Model No.

Lens

Power Input Vol tage

System

Sync. Mode

Pick Up Element

Effect ive Pixe ls

Chip Size

Hor izonta l & Ver t ica l

Sync. Frequency

Scanning System

Inf rared Cut Fi l ter

Resolut ion

Min imum I l luminat ion

S/N Rat io

Auto Gain Contro l

Whi te Balance

Aper ture Correct ion

Power Consumpt ion

Back Light Compensat ion

Video Output

Operat ing Temperature

Gamma Character is t ic

IP Rat ing

Inf rared

LEDBeam Spread

Peak Wavelength

Radiant Dis tance

Dimension

Weight

Focal Length

I r is

Angle of v iew

H

V

D

CMR254X3.6

4 ~ 9mm

F1.6

NTSC or PAL

AC24V ( 10%)

Interna l

1/3" Super HAD CCD Sensor

768(H) x 494(V) [NTSC]

752(H) x 582(V) [PAL]

5.59mm(H) x 4.68mm(V)

15.734 KHz / 59.94Hz [NTSC]

15.625 KHz / 50Hz [PAL]

2:1 Inter lace

0 Lux With IR ON

Auto Selectable, Automatic Switch

From Color Mode To Monochrome

Color : 540TV Lines , Mono: 600TV Lines



More Then 50dB (AGC-OFF)

36dB Var iab le Gain

ATW

Hor izonta l , Ver t ica l

7 .2W

Auto

CVBS 1.0Vp-p, 75ohm

IP68

850nm

30

35M

-10 ~ +50 (14 ~ 122 )

118mm(W) x 103mm(H) x 250mm(D)

730g

=0.45

CMR258X3.6 CMR254X2.2 CMR258X2.2

Design and speci f icat ions are subject to change wi thout not ice.

D/N SUPER HIGH RESOLUTION VARI-FOCAL IR CAMERA

AC100~240V

Window 79 Heat Resistant Glass

3.3 ~ 12mm

F1.4

89.8 ~ 23.9 69 ~ 30.7

63.6 ~ 17.9 51 ~ 23

125.7 ~ 29.9 86 ~ 38.5

AC24V ( 10%) AC100~240V



66-CMR22CSE-1

INSTRUCTION MANUAL

66-CMR22CSE

MERIT LILIN ENT. CO., LTDhttp://www.meritlilin.com

D/N VARI-FOCAL IR CAMERACMR224X/228X/254X/258X3.6

CMR224X/228X/254X/258X2.2

Documents

D/N VARI-FOCAL IR CAMERA - VERROCCHIOPRECAUTIONS Do not drop or strike this equipment. Do not install the equipment near any naked flames or heat sources. Do not expose this unit to