Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Document no. 3420 Mellanox Technologies Confidential
http://www.mellanox.com
Dismantling Guide
OPN: MTS3610
Rev. 1.0
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
2 of 22
NOTE:
THIS INFORMATION IS PROVIDED BY MELLANOX FOR INFORMATIONAL PURPOSES ONLY AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS HARDWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Mellanox Technologies, Inc.
350 Oakmead Parkway Suite 100
Sunnyvale, CA 94085
U.S.A.
www.mellanox.com
Tel: (408) 970-3400
Fax: (408) 970-3403
Mellanox Technologies Ltd
PO Box 586 Hermon Building
Yokneam 20692
Israel
Tel: +972-4-909-7200
Fax: +972-4-959-3245
© Copyright 2011. Mellanox Technologies, Inc. All Rights Reserved.
Mellanox®, BridgeX®, ConnectX®, InfiniBlast®, InfiniBridge®, InfiniHost®, InfiniRISC®, InfiniScale®,
InfiniPCI®, PhyX® and Virtual Protocol Interconnect® are registered trademarks of Mellanox Technologies, Ltd.
CORE-Direct and FabricIT are trademarks of Mellanox Technologies, Ltd. All other marks and names mentioned
herein may be trademarks of their respective companies.
Contact Information
Should you have any questions regarding our Products, please feel free to contact us directly or contact our
local distributors.
Mellanox Technologies Call Center Tel: +
Email: [email protected]
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
3 of 22
Table of Contents
Revision .......................................................................................................................................... 5
Preface............................................................................................................................................. 5 Intended Audience .......................................................................................................................... 5 Switch OPNs ................................................................................................................................... 5 Policy Statement ............................................................................................................................. 6 1 Dismantling Instructions ......................................................................................................... 7
1.1 Chassis Switch System Systems - General ..................................................................... 7 1.2 General Preparations ....................................................................................................... 7
2 Extraction of the Modules ....................................................................................................... 8
2.1 Extracting the Power Supply Unit (PSU) ....................................................................... 8 2.1.1 PSU Sub Assembly Disassembling ............................................................................ 9
2.2 Extracting the Leaf Board ............................................................................................... 9 2.2.1 Leaf Module Sub Assembly Disassembling ............................................................. 11
2.3 Extracting a Spine Board .............................................................................................. 11 2.3.1 Spine Module Sub Assembly Disassembling ........................................................... 13
2.4 Management Module Extraction................................................................................... 14
2.4.1 Management Module Sub Assembly Disassembling ............................................... 15
2.5 Battery Extraction ......................................................................................................... 17 2.6 Memory Card Extraction .............................................................................................. 17
2.7 Fan Extraction ............................................................................................................... 19 2.7.1 Fan Module Sub Assembly Disassembling .............................................................. 20
3 Chassis and Backplane .......................................................................................................... 21
List of Tables
Table 1: Revision ...................................................................................................................... 5
Table 2: Switch OPNs for this Procedure ................................................................................. 5
Table of Figures
Figure 1 Front and Rear View of the MTS3610 ....................................................................... 7 Figure 2 Spine Side of Chassis .................................................................................................. 8 Figure 3 Power Supply Unit ...................................................................................................... 8 Figure 4 Remove the Mechanical Enclosure and Fans ............................................................. 9 Figure 5 Removing a Leaf ....................................................................................................... 10
Figure 6 Leaf Latches .............................................................................................................. 10 Figure 7 Mechanical Enclosure Screw Locations ................................................................... 11 Figure 8 Spine Side ................................................................................................................. 12
Figure 9 Ejector Latch ............................................................................................................. 13 Figure 10 Remove the Screws ............................................................................................... 13 Figure 11 Management Module ............................................................................................ 14 Figure 12 Management Module Latches ............................................................................... 15
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
4 of 22
Figure 13 Management Module ............................................................................................ 16 Figure 14 Remove Battery .................................................................................................... 17 Figure 15 Memory Card Location ......................................................................................... 18
Figure 16 Memory Card Slots ............................................................................................... 18 Figure 17 Remove Fan Modules ........................................................................................... 19 Figure 18 Remove the Fan Module Cards............................................................................. 20 Figure 19 Remove the Chassis Screws.................................................................................. 21
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
5 of 22
Revision
Table 1: Revision
Revision Date
1.0 Oct. 2010
Preface
This manual is intended as a reference for dismantling MTS3610 switch systems in
preparation of meeting the requirements of WEEE recycling.
Intended Audience
This manual is intended for technicians who dismantle the switch systems, as a reference
for WEEE recyclers.
Mellanox Technologies emphasizes the importance of carefully following all procedures
described in this guide to prevent personal injury.
Switch OPNs
This document is valid for all of the switch OPNs listed in Table 2.
Table 2: Switch OPNs for this Procedure
MTS3610
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
6 of 22
Policy Statement
Mellanox Technologies recognizes the importance of developing connectivity solutions
that not only enable our customers to optimize their data centers performance, but also
protect the environment and ensure that future generations enjoy its bounties. Mellanox
Technologies is committed, therefore, to meeting the requirements of the European
Union’s WEEE (waste electrical and electronic equipment) directive. The directive
mandates how the materials used in electrical and electronic equipment must be disposed
of.
Mellanox Technologies has worked closely with its suppliers to eliminate hazardous
materials from its products. There are instances, however, where it has not proven
possible to completely eliminate all hazardous materials. Consequently, all applicable
products are labeled with a crossed out “wheelie” bin symbol, indicating that special care
must be applied to their disposal and / or recycling.
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
7 of 22
1 Dismantling Instructions This chapter provides detailed instructions for dismantling the InfiniBand chassis switch
systems. Follow the instructions in the order they are presented.
1.1 Chassis Switch System Systems - General
The chassis switch system complies with the RoHS directive under the exemption known
as RoHS-R-5.
Chassis switch systems are comprised of:
Leaf modules
Spine modules
Management modules
Fan modules
Power supply modules
Chassis and other mechanical parts such as slot dividers
Backplane
Figure 1 Front and Rear View of the MTS3610
1.2 General Preparations
The switch system is assembled using Philips screws, and handles with snap in latches
for modules.
To disassemble the switch system parts you will need a small Philips screwdriver.
The pictures displayed in the following pages provide visual guidance explaining how to
remove the modules from the mechanical base.
Spines
Power
supplies
Fan module
Leafs
Fan module
Management
modules
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
8 of 22
2 Extraction of the Modules
2.1 Extracting the Power Supply Unit (PSU)
Figure 2 Spine Side of Chassis
To extract a PSU:
1. Remove the power cord from the power supply unit.
Figure 3 Power Supply Unit
2. Grasping the handle with one hand, push the black latch release while pulling the
handle outward.
Power Supply Units
Latch
Handle
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
9 of 22
3. Remove the PSU.
4. Remove all PSUs from the chassis.
2.1.1 PSU Sub Assembly Disassembling
After removing the PSUs use a Philips screwdriver to disassemble the mechanical covers
and remove all sub components.
Figure 4 Remove the Mechanical Enclosure and Fans
5. Remove the Fans from the PSU.
2.2 Extracting the Leaf Board
There are up to 18 leaf modules located on the front side of these products.
The leaf module is removed from the chassis using snap handles.
The following pictures show how to open the snap handles and remove the leaf module
from the chassis.
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
10 of 22
Figure 5 Removing a Leaf
Figure 6 Leaf Latches
1. Push from the center of the leaf in an outward direction on the red buttons.
2. Continue pushing outward until the snaps pop.
3. Grab the snaps and pull the leaf out of the chassis.
4. Remove all leafs from the chassis.
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
11 of 22
2.2.1 Leaf Module Sub Assembly Disassembling
1. After removing the modules use a Philips screwdriver to disassemble the mechanical
covers and remove all sub components.
Figure 7 Mechanical Enclosure Screw Locations
2. Remove the Heat sink and the board.
2.3 Extracting a Spine Board
There are up to 9 Spine modules located on the rear side of the product.
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
12 of 22
The Spine module is removed by opening the handles.
Figure 8 Spine Side
1. Push outward on the latches to unlock the ejectors from the chassis.
2. Open the ejectors until they are 90 degrees from the module.
3. Pull out on the module using both ejectors.
4. Remove all spines from the chassis.
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
13 of 22
The following pictures show how to use the snap handles to remove the Spine module
from the chassis.
Figure 9 Ejector Latch
2.3.1 Spine Module Sub Assembly Disassembling
After removing the modules use a Philips screwdriver to disassemble the mechanical
covers and remove all sub components.
Figure 10 Remove the Screws
Lock for the Ejector Latch
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
14 of 22
Remove the Heat sink and the board.
2.4 Management Module Extraction
There are 1 or 2 management modules located on the front side below the leaf modules.
The management module is removed using the snap handles.
Figure 11 Management Module
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
15 of 22
Figure 12 Management Module Latches
1. Push from the center of the leaf in an outward direction on the red buttons.
2. Continue pushing outward until the snaps pop.
3. Grab the snaps and pull the leaf out of the chassis.
4. Remove all management modules from the chassis.
2.4.1 Management Module Sub Assembly Disassembling
After removing the modules use a Philips screwdriver to disassemble the mechanical
covers and remove all sub components.
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
16 of 22
Figure 13 Management Module
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
17 of 22
2.5 Battery Extraction
In all Mellanox systems where there is a CPU board and / or management board, there is
a: COIN TYPE LITHIUM BATTERY CR1620 3V 75MA.
Figure 14 Remove Battery
2.6 Memory Card Extraction
There are 1 or 2 Memory cards in the MTS3610 systems.
1. Unscrew and remove the wing nut.
2. Remove the lock down clamp.
3. Remove the memory card(s) by pulling it out of the card slot.
Remove the
battery
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
18 of 22
Figure 15 Memory Card Location
Figure 16 Memory Card Slots
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
19 of 22
2.7 Fan Extraction
There are 2 Fan modules located in the MTS3610 system.
One is horizontal and one is vertical.
Figure 17 Remove Fan Modules
Leaf Side Fan
Module
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
20 of 22
1. Unscrew the four thumbscrews using your fingers or a Phillips screwdriver. They are
captured and will not come out.
2. Pull the two handles simultaneously, and slide out the fan module.
2.7.1 Fan Module Sub Assembly Disassembling
After removing the modules use a Philips screwdriver to disassemble the mechanical
covers and remove all sub components(fans and fan cards).
Figure 18 Remove the Fan Module Cards
Spine Side Fan
Module
Fan cards
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
21 of 22
3 Chassis and Backplane
After removing and disassembling all field replaceable modules use a Philips screwdriver
to disassemble the chassis and the Backplane.
1. Remove the top and side screws to remove the cover and side panels.
2. Slide out the cover.
3. Unscrew the backplane screws and remove the backplane.
Figure 19 Remove the Chassis Screws
Screws
Dismantling Guide Rev. 1.0
Mellanox Technologies Confidential
22 of 22