New York Stucco Direct Applied Finishing System — Technical Data (REV B. 040313) — Page 1

Direct Applied Finishing System

Description:

NEW YORK STUCCO Direct Applied Finishing System(DAFS) is utilized over masonry substrates wherever ahighly durable, textured, and uninsulated wall system isrequired. The DAFS design eliminates the use of EPSor XPS insulation board, and is often used for soffits andareas that do not need an EIFS system. The base coat,mesh and finish are applied directly to the substrate.

Advantages:

• Lightweight

• Fade resistant

• Substantial savings on reduced structuralrequirements

Surface Preparation: All surfaces must be thor-oughly cured, dry and clean before the NEW YORKSTUCCO Direct Applied Finishing System is employed.Moisture content of these surfaces shall not exceed16% except for white coat plaster which may not ex-ceed 6% of moisture. A minimum air and wall surfacetemperature of 50°F must be maintained during, andfor 48 hours following, installation.

Masonry Block: Block shall be laid perfectly plumband true, free of excess mortar and with all jointsneatly tooled to a concave joint. All defects, i.e.chipped edges, large voids, etc., shall be carefullypointed and filled with mortar. All projecting mortarshall be ground and large holes shall be filled. Porousblock shall be air pressure dusted to remove looseparticles. All mortar joints shall be thoroughly cured.

Poured or Precast Concrete: No curing com-pounds or form release agents which may affectproper coating adhesion shall be used. Immediatelyafter forms have been stripped, all fins and otherprojections shall be removed. Voids and other dam-aged areas shall be filled with block fill. Tie rods orother projecting metal must be cut back at least oneinch and coated with a cement mortar mixture. Allsurfaces shall be rubbed with a carborundum brickto produce a smooth, even finish. Do not use a ce-ment wash.

NEW YORKSTUCCODirect Applied Finishing Systemsdo not use EPS or XPS insulationfoam in the design configuration.

Weather barrier, base coat, meshand finish are applied directly tothe substrate.

This application is widely used forsoffits and areas that do notrequire an EIFS system.

TM

Formulated Solutions LLC 25 -44 Borough Place

Woodside, NY 11377 USA

T 1 718 267 6380F 1 718 204 6013

www.formulatedsolutions.net

NEW YORK STUCCO is a trademark of Formulated Solutions LLC

New York Stucco Direct Applied Finishing System — Technical Data (REV B. 040313) — Page 2

NOTE: New York Stucco Additive and Bonding Agentaids in bonding new base coat to existing masonryor concrete substrate. If a potential adhesion prob-lem exists due to old, worn, flakey or contaminatedsurfaces, coat the substrate with New York StuccoAdditive and Bonding Agent before applying NewYork Stucco Base Coat.

Plaster: Surface shall be finished with a Portland ce-ment, steel troweled finish. Vermiculite, Perlite orKeene Cement plaster is not acceptable.

Previously Painted Surfaces: Consult a NEW YORKSTUCCO representative for proper recommendations.

Components:

· NEW YORK STUCCO Additive and Bonding Agent

· NEW YORK STUCCO Base Coat

· NEW YORK STUCCO Fiberglass Mesh

· NEW YORK STUCCO Finish

Application: Using a short-nap roller, apply an evencoat of New York Stucco Additive and Bonding Agentover the entire surface. Immediately after the New YorkStucco Additive and Bonding Agent is dry, coat the sur-face with NEW YORK STUCCO Base Coat approxi-mately 1/16” to ¼” thick with a stainless steel trowel.Embed NEW YORK STUCCO Fiberglass Mesh into basecoat. After the NEW YORK STUCCO Base Coat is fullycured apply the NEW YORK STUCCO Finish. Review in-dividual product data sheets and package informationfor full instructions on application and use.

Colors: 48 standard colors from NEW YORK STUCCOFinish color chart.

Technical Assistance: Telephone Formulated Solu-tions Monday through Friday, 8:00 AM to 4:30 PM EST:(718) 267-6380 ext. 111 or FAX inquiry to (718) 204-6013.

Notice and Warranty Disclaimer: FormulatedSolutions (FS) products are intended for useby qualified professional contractors, not D-I-Y consumers or handymen. Finishing sys-tems and/or components must be specifiedby a qualified design professional, generalcontractor or builder as an element of alarger construction project. It must be in-stalled in accordance with FS’s instructions,the designer’s specifications and local build-ing code. Improper use of FS products oruse as part of an improperly designed orconstructed larger assembly or building mayresult in serious damage to this product, andto the structure of the building or its com-ponents.

FS disclaims all, and assumes no, liability for• products improperly applied by unqualifiedpersons or entities • an improperly designedor constructed building • the nonperfor-

mance of adjacent building components orassemblies • other construction activities be-yond FS’s control • on-site inspections.

FS has provided the enclosed Instructionsand Recommendations (I/R) to assist theUSER in the application of this product.These I/Rs are not warranted to be compre-hensive, complete, thorough or conclusiveas regards any specific installation. It is theUSER’S obligation to ensure that the productis suitable for its intended use and that it iscompatible with existing conditions or ap-plications of other coincident or adjoiningmaterials. The liability of the SELLER andMANUFACTURER, whether express or im-plied, whether in contract or in tort, arisingout of warranties, representations, instruc-tions or defects from any cause shall be lim-ited exclusively to replacing the product,provided the same is proved defective, or re-

funding the purchase price upon return ofthe unused product. In no event will SELLERor MANUFACTURER be liable for conse-quential dam- ages, including but not lim-ited to loss of materials, costs of labor, lossof profits, costs of replacement goods, orother commercial loss. The USER acceptsthe product AS IS, and without warrantiesexpress or implied. Subject to FS approval,certain installations may be eligible for alimited warranty provided by FS. For furtherinformation, please contact your Distributor.

For the most current and complete informa-tion on proper application, clean-up, mixing,specifications, warranties, cautions and dis-claimers, please refer to the company man-ual or our website at www.formulatedsolu-tions.net.

Coverage:

Product Coverage Sq./ Ft. per unit Packaging

Additive and Bonding Agent 1500 5-gal. pailBase Coat 100 50-lb. bagFinish 140 5-gal. pailMesh 450 4 rolls per cartonWeather Barrier 280 25-lb. bag

New York Stucco Direct Applied Finishing System — Technical Data (REV B. 040313) — Page 3

1 Framing

2 Sheathing

3 New York Stucco Additive and Bonding Agentor New York Stucco Weather Barrier

4 Cement board

5 New York Stucco Base Coat with embedded reinforcing mesh

6 New York Stucco Primer

7 New York Stucco Finish

NEW YORK STUCCODirect Applied Finishing System (DAFS)