Upload
lyngoc
View
213
Download
0
Embed Size (px)
Citation preview
Installation instruction for 140G-H, 140MG-HIstruzioni di installazioneInstallationsanleitungInstructions pour linstallationInstrucciones de instalacin
Bul. 140G/140MG
DIR 1000721R0001 Version 03
DIR 1000721R0001 Version 03 - 140G-H_, 140MG-H_
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfllen trennen. Die Gerte mssen in einem passenden Gehuse eingebaut und gegen Verschmutzung geschtzt werden. (Befolgen Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour viter toute dcharge. Prvoir une mise en coffret ou armoire approprie. Protger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconctese de la corriente elctrica, antes de la instalacin o del servicio, a fin de impedir sacudidas elctricas. Instlelo en una caja apropiada. Mantngalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENO: Para evitar choques, desconectar da corrente eltrica antes de fazer a instalao ou a manuteno. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigncias da norma NFPA70E).
Installation - Installazione - Instalacin Instalao - -
NFPA70E
NFPA70E
CLACK
1
from 0.51" to 0.55"
from 13 mm to 14 mm
dia.
0.1
3" 3
.5 m
m
x2
3p
4p
x2
x2
x2
x2
x2
x4
x6
x6
x8
x1
x1
x2
x2
x2
x2
Phasebarrier
End cap kit Carter Insulator Sidecover
Insulator
CH 5
CH 7
140G-G-MH3
140G-G-MH4
140G-G-PB3M
140G-G-PB4M
Mounting hardware
140G-H-ECM3
140G-H-ECM4
M
M 4
LENGTH M
85 mm (3.35") M 4
LENGTH M
1 4 mm (0.55") M 6
LENGTH dia.
1 2 mm (0.47") 3
2
(2)
1
7.8
7"/
20
0 m
m
- Use cable or insulated busbars/ or perform specific type test on the installation.- Usare cavi o barre isolate/ o eseguire prove di tipo specifiche sull' installazione. - Kabel oder isolierte Sammelschienen verwenden/ oder die spezifische Typprfung auf derInstallation durchfhren.- Utiliser un cble ou des barres isoles/ ou raliser un test de type spcifique sur installation.- Utilizar un cable o barras aisladas/ o efectuar una prueba de tipo especfico sobre instalacon.
7.8
7"/
20
0 m
m
Maximum recommended conductor support distance
DIR 1000721R0001 Version 03
(3)
3
A B C D E
III-IV3.62"
92.5 mm
1.69"
43 mm
1.85"
47 mm
0.67"
17 mm
0.93"
23.5 mm
III3.31"
84.5 mm
2.95"
75 mm
3.39"
86 mm
0.98"
25 mm
1.69"
43 mm
IV3.31"
84.5 mm
2.95"
75 mm
4.57"
116 mm
0.98"
25 mm
1.69"
43 mm
III3.43"
87 mm
3.27"
83 mm
3.7"
94 mm
1.14"
29 mm
1.85"
47 mm
IV3.43"
87 mm
3.27"
83 mm
4.88"
124 mm
1.14"
29 mm
1.85"
47 mm
WITH ESCUTCHEON
WITHOUT ESCUTCHEON
Cannot be reversewired (feed) above 480V
LINE
LOAD
UE>4 0V8
0.9
8"/
25
mm
0.98"/25 mm
0.9
8"/
25
mm
0.98"/25 mm
1
2
4
OK
3
EC
DBdia. 0.18" 4.5 mm-M4
A
Y
X
YX
Y
Y
X
X
IV ONLY
III ONLY
IV ONLY
III ONLY
IV ONLY
III ONLY
IV ONLY
0.59"/15 mm 4.3
7"/
11
1 m
m2.1
8"
1.77"/45 mm IV
0.59"/15 mm III
IV ONLY
1,1 Nm8.9 lb-in
MANDATORY FORUL APPLICATIONNOT REQUIRED FORIEC APPLICATIONS
55
.5 m
m
4
max
7,5
min
6,5
max 2
0
0,2"/5 max0,08"/2,5 min
max 0
,78"
dia. min 0.26" min 6,5
max
0,3
"m
in 0
,26"
20
dia. 0.26" 6.5
0,78"
DIR 1000721R0001 Version 03
140G-H THERMOMAGNETIC TRIP UNIT
(4)
CLACK
1
MAX
MED
MIN
l3MAX MED MIN MAX MED MIN
l1
MAX
MED
MIN
USE FLAT BLADESCREW DRIVER
2
1
2
5
7
940 1250
77 93 110 550 825 1100
70 85 100 500
Adjustable
Adjustable
80
90
100
110
125
160*
Adjustable
Adjustable
56 68 80 400
800112 136 160
87 106 125 625
Adjustable
Adjustable
I1
20
25
30
32
Fixed
Fixed
Fixed
Fixed 60
In
16
15
Type
Med Max Min
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Type In
400
32 400
Med Max
15 400
25 400
30
400
20 400
35
40
50
60
63
70
16
600
1200 1600
I3
35 400
40 400
50 500
63 630
70 700
750 1000
600 800
63 76.5 90 450 675 900
Min
*IEC ONLY
- Manually trip the breaker prior to adjustment of the magnetic settings.
- Eobbligatorio mettere l'interruttore in posizione Trip test prima di regolare il termomagnetico.
- Der Leistungsschalter muss vor Einstellung des thermomagnetischen Auslsers zwingend in die Prfstellung geschaltet werden.
- Il est obligatoire de mettre le disjoncteur en position de Test de Dclenchement avant de rgler le dclencheur magntothermique.
- Es obligatorio situar el interruptor en posicin Test de Disparo antes de realizar el ajuste del rel termomagntico.
6
Frame can be removedfor IEC installation
ONLY REQUIRED FOR THROUGH THE DOOR APPLICATION(WITH DOOR OF THE PANEL 0,98"/25mm FROM THE FRONT)
DIR 1000721R0001 Version 03
8
1
- Green- Verde- Grn- Vert
- Verde
- Red- Rosso
- Rot- Rouge- Rojo
- Device ON- Dispositivo acceso
- Einrichtung eingeschaltet- Dispositif allum
- Dispositivo encendido
- Change battery- Sostituire batterie- Batterie ersetzen
- Remplacer batteries- Sustituir bateras
CLACK4
2
DIAGISTIKABLAUF- EINEITHSPRUF-LED: Alle LEDs des Relais mssen aufleuchten- ANGABE DER LETZTEN AUSLOSUNG: Wenn im Speicher des Relais vorhanden.- LED: Bleibt angeschaltet, bis die Einheit 140G-ELTT tester an die Relais angeschlossen ist.- AUSLOSEBEREIT
PROCEDIMIENTO DIAGNOSTICO- LED CONTROL UNIDAD: todos los led del rel se deben encender- INDICACION ULTIMA ACTUACION: si est presente en la memoria del rel- LED: queda encendido mientras la unidad 140G-ELTT tester permanezca conectada con el rel- LISTO PARA LA ACTUACION
PROCDURE DE DIAGNOSTIC- UNIT CHECK LED : toutes les diodes du relais doivent s'allumer- LAST TRIP INDICATION : si prsente dans la mmoire du relais- LED: la DIODE reste allume tant que l'unit 140G-ELTT tester est connecte au relais- READY TO TRIP
TRIP TESTER 140G-ELTT (order separately)
LED TRIP UNIT DEVICE
140G/140MG-H ELECTRONIC TRIP UNIT
DIAGNOSTIC PROCEED- UNIT CHECK LED: all the leds in the relay must come on- LAST TRIP INDICATION: led will come on only when a trip occurred- LED: remains on for as long as the 140G-ELTT tester is connected to the relay- READY TO TRIP
PROCEDURA DI CONTROLLO- CONTROLLO LED: tutti i led del rel si devono accendere- ULTIMA INDICAZIONE DI TRIP: se presente nella memoria del rel- LED: resta acceso finch lunit 140G-ELTT tester e connessa al rel- PRONTO PER TRIP
140MG-H MAGNETIC ONLY TRIP UNIT
- Manually trip the breaker prior to adjustment of the magnetic settings.
- Eobbligatorio mettere l'interruttore in posizione Trip test prima di regolare il termomagnetico.
- Der Leistungsschalter muss vor Einstellung des thermomagnetischen Auslsers zwingend in die Prfstellung geschaltet werden.
- Il est obligatoire de mettre le disjoncteur en position de Test de Dclenchement avant de rgler le dclencheur magntothermique.
- Es obligatorio situar el interruptor en posicin Test de Disparo antes de realizar el ajuste del rel termomagntico.
H A B C D E F G H I
3 411 In 12 15 17 20 23 25 28 30 33
7 411 In 28 34 40 46 53 59 65 71 77
15 311 In 45 60 75 90 105 120 135 150 165
30 311 In 90 120 150 180 210 240 270 300 330
50 311 In 150 200 250 300 350 400 450 500 550
70 311 In 210 280 350 420 490 560 630 700 770
80 311 In 240 320 400 480 560 640 720 800 880
100 311 In 300 400 500 600 700 800 900 1000 1100
125 510 In 625 703 781 859 938 1016 1094 1172 1250
l3
MIN
MA
X
ME
D
MIN
l1
MA
X
ME
DM
IN
MA
X
ME
DM
IN
1
2
USE FLAT BLADESCREW DRIVER
CLACK
FC
D
B
E
HG
AI
900 1000 1100
A B C D E
300 400 500 600 700
I3
F G H I
9
(5)
3
DIR 1000721R0001 Version 03
DIR 1000721R0001 Version 03 (B0749) - B0876 Copyright 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN097D-MU-P - June 2016
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
T kAI2t
(106A2s)
PEAK
CURRENT
(A)
FREQ
(Hz)
6 0.266 10000 60
30 0.48 19000 60
65 0.512 23200 60
6 0.3 10000 60
14 0.472 14100 60
25 0.655 18000 60
140G-HC6 480
600
V kAI2t
(106A2s)
PEAK
CURRENT
(A)
FREQ
(Hz)
6 0.266 10000 60
50 0.486 21000 60
100 0.704 31100 60
6 0.3 10000 60
22 0.655 18000 60
35 0.65 20000 60
140G-HC0 480
600
10 CURRENT LIMITING PERFORMANCES
Page 1Page 2Page 3Page 4Page 5Page 6
CONFIDENTIAL AND PROPRIETARY INFORMATION. THIS DOCUMENT CONTAINS CONFIDENTIAL AND PROPRIETARY INFORMATION OF
ROCKWELL AUTOMATION, INC. AND MAY NOT BE USED, COPIED OR DISCLOSED TO OTHERS, EXCEPT WITH THE AUTHORIZED WRITTEN
PERMISSION OF ROCKWELL AUTOMATION, INC.
Sheet
Size Ver
Of 11
A 0110000028320Dr. DateG. USHAKOW 8-23-13
MATERIALSIZE
FOLD
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
FLAT
SPECIFICATIONS FORINSTRUCTION SHEET CREATED BY STRATEGIC PARTNER
This Instruction Sheet is Being Printed by Strategic Partner
Note: After folding---Printed in (Country where printed*), part number(s) and barcode (when used) should be visible.
* The printing vendor may change the instruction sheet files to show the correct country.