Digital Selective Calling (DSC)

Introduction

DSC is, basically, a paging system that is used to automate distress alerts sent over terrestrial (i.e.: non-satellite) VHF, MF and HF marine radio systems.

The DSC system's digital processing techniques, combined with the relatively narrow receiver bandwidths used, provide a DSC signal with resistance to noise and fading over the radio path.

This results in increased range compared with radiotelephone transmissions.

Unfortunately, DSC remains one of the GMDSS' least understood sub-systems.  This lack of understanding is reflected in the very high DSC false alert rate.

Operations

DSC is used to establish initial contact between stations.

Following an alert by DSC, communications are normally carried out by radiotelephone or Narrow Band Direct Printing (NBDP - radio telex).

DSC can be considered as a replacement for the radiotelephone and radiotelegraph (Morse) alarm signals.

Rather than just indicate that the sending station is in distress, the DSC system allows a great deal more information to be transmitted, including:

the priority of the call - DISTRESS, URGENCY, SAFETY or ROUTINE;the address - ie: all ships or a single ship/station;the identification of the ship in distress;the position of the ship in distress; andthe nature of the distress.

DSC channels

The ITU has allocated a DSC distress and safety channel in the MF, each of the HF and the VHF marine radio bands.  These are:

MF/HF DSC

DISTRESS AND SAFETY CHANNELS

2187.5 4207.5 6312.0 8414.5 12577.0 16804.5 (kHz)

VHF DSC

DISTRESS AND SAFETY CHANNEL

VHF marine channel 70

Note that voice transmissions are PROHIBITED on the DSC channels.

The MF/HF channels are restricted to distress, urgency and safety traffic only because of the relatively low speeds of transmission of 100 baud. If too many calls were permitted on the MF/HF channels, the channels would quickly become overloaded to the point where a distress call may be blocked.

VHF DSC operates at 12 times the speed of MF/HF - accordingly, all priorities of call are allowed on the VHF channels.

The ITU has also allocated a suite of HF channels dedicated to DSC commercial operations.  These may be found in the ITU DSC operational specification (the link is at the bottom of this page).

DSC call categories

The DSC system supports a number of call categories. These categories mirror the standard maritime prioritisation of message traffic, ie:

DISTRESS

URGENCY

SAFETY

ROUTINE

Distress alerts are automatically addressed to all stations.

Urgency, safety and routine calls can be addressed to all stations, an individual station, or a group of stations.

Maritime Mobile Service Identities (MMSI)

All DSC equipment is programmed with a unique nine digit identification number, known as a Maritime Mobile Service Identity (MMSI).

The MMSI is sent automatically with each and every DSC transmission made.

Maritime Identification Digits (MID)

The first three digits of the MMSI are known as the Maritime Identification Digits (MID). The MID represents the country of registration of the vessel, or the country in which the DSC shore station is located. MIDs are allocated on an international basis by the ITU, in much the same way as a callsign prefix.

The MID list may be found here (opens in new window).

Formation of MMSI's

MMSIs allocated to merchant vessels are normally allocated with three trailing zero's.

Those allocated to recreational craft have two or one trailing zero, Coast Station MMSI's are formed with two leading zero's, those allocated to SAR aircraft use 111 as the first three digits, hand held radios have 8 as

a leading digit and Man Overboard beacons have their own code structure, starting with 972.

 

For example:

Typical Australian merchant vessel MMSI- 503001000

where:

503 is the Australian MID;and

01000 is the individual ship number

Typical Australian recreational vessel MMSI - 503000100

where:

503 is the Australian MID;and

000100 is the individual ship number

 

Coast Station MMSI - 005030001

where:

503 is the Australian MID; and0001 is the individual Coast Station number

 

SAR aircraft MMSI - 111503123

where:

503 is the Australian MID; and123 is the individual aircraft number

 

Hand held radio with DSC MMSI - 850312345

where:

503 is the Australian MID; and12345 is the individual radio number

 

Typical DSC man overboard beacon - 972450001

where:

972 is the DSC MoB code;45 is the manufacturer code

and0001 is the individual beacon number

 

MMSI databases

The ITU operate an international web-based data base of MMSI's, known as the Maritime Mobile Access and Retrieval System (MARS).

The Australian MMSI list may be found here.

 

DSC equipment

GMDSS DSC equipment is normally comprised of a stand alone control

unit, with an alpha-numeric display screen and a keyboard on which to compose messages.

Typical VHF DSC controller - note display screen and keyboard.

The control unit controls the actions of the DSC modem (modulator demodulator).  The modem is interfaced to a DSC watchkeeping receiver - this receiver is fixed tuned to either the VHF DSC channel (ch. 70), the 2 MHz DSC channel, or the HF DSC channels.

HF DSC watchkeeping receivers are designed to scan the 6 MF/HF DSC channels in rapid sequence (2 seconds or less).

DSC watchkeeping receivers are fitted with their own dedicated antennas.

The DSC modem decodes all calls on the frequency to which the watchkeeping receiver is tuned.  If calls are received addressed to all ships, or to the particular ship on which the DSC system is fitted, the DSC controller sounds an alarm, and displays the decoded information on the alpha-numeric display.

MF/HF DSC operator control unit

 

To transmit a DSC call, a GMDSS operator enters the required commands to identify the station (or stations) with which communication is desired, the priority (DISTRESS, URGENT, SAFETY or ROUTINE) and the purpose of the call.

Once the call is composed, the CALL button is pressed on the DSC controller, and the information is sent to the associated transmitter for transmission.

All DSC systems provide complete remote control of the associated transmitter - the selected DSC frequency information is fed to the transmitter over a serial control link from the DSC controller.

The whole process is automated - the DSC system instructs the transmitter to change to the required DSC channel, the transmitter changes channel and (in the case of MF/HF systems) tunes its antenna system.  The transmitter then signals a ready command to the DSC controller, which sends the information for broadcasting.  The entire process takes only 3 to 5 seconds.

DSC controllers are also required to be interfaced to GPS receivers for automatic updating of position and time information.  This information is automatically included in distress calls.

DSC controllers are also required to be equipped with a DISTRESS button, which allows the transmission of a distress call with minimum delay. The button is required to be protected by a cover, and also can only be activated after "2 separate and independent actions".

Videos of DSC traffic being received and sent on Coast Station equipment may be found here.

OPERATIONAL PROCEDURES

The official guide to DSC procedures is contained in ITU recommendation ITU-R M.541-9.  The complete text of the recommendation may be found here.

IMO have issued a circular which contains further clarifications on DSC procedures:

IMO Comsar Circular 25 - Procedure for responding to distress alerts by ships.(dated March 15th 2001 - includes flow chart.)

IMO DSC flow charts

The IMO have issued flow charts to provide guidance to users of DSC systems:

(These files require Adobe Acrobat reader)

IMO flow chart - Actions on receipt of a VHF DSC call

IMO flow chart - Actions on receipt of a MF DSC call

IMO flow chart - Actions on receipt of a HF DSC call