Diesel Cylinder Heads & Engine Accessories - SeekPartfile.seekpart.com/keywordpdf/2011/5/13/201151314549739.pdf · Diesel Cylinder Heads & Engine Accessories ... Big Cam IV-NTC 400

CATALOG DCH0502

Diesel Cylinder Heads

& Engine Accessories

Diesel Cylinder Heads

& Engine Accessories

Customer satisfaction ensured by quality controlled processes

Magnafluxed for cracks

Repaired and brought back to specifications

Built with NEW guides, injector tubes, freeze plugs, seals and keepers

100% Air decay and wet pressure tested

Surface ground

Machined in seat areas and vacuum tested

Sealed with a rust preventative coating

All ALLIANCE Cylinder Heads are:All ALLIANCE Cylinder Heads are:

3406B

MODEL DESCRIPTION CYL CASTING ID

C10 / C12Reference # 132-3245 144-2967

' 97 On-Highway6 4P6510

C10 / C12 Reference # 133-7052' 98 On-Highway 6 4P6510

C-15 14.6 liter / 893 / 99-03 6

D315Industrial Cylinder Head

4 CylinderReference # 8B6454

4

7F37644F55086H87277H3469

D318

Industrial Cylinder Head6 Cylinder

Reference # Long 5F13057H9853

Reference # Short5B52405B5239

6

LONG3F99037F78786H8612SHORT5B51965B83477B2416

D320 Industrial Cylinder HeadReference # 5M8153 4

2M67575M76008H8805

D330 Industrial Cylinder HeadReference # 2S9004 4 8M670

2S9000

D330-C Industrial Cylinder HeadReference # 7S7070 4 5S6700

5S2222

D333 Industrial Cylinder HeadReference # 5S1884 6 2S9790

2M5417

D333-C Industrial Cylinder HeadReference # 1P4303 6 1P4302

1P6370

D334/1674 Industrial Cylinder HeadReference # 5S8048 6 9S4848

3S7707

D340 Industrial Cylinder HeadReference # 5M7601-8M226 4 8M200

5M3700

D342Early

Industrial Cylinder HeadReference # 8N6004

Non-Spacer Plate6 8H5980

4H7258

D342Late


Spacer Plate1/2" or 3/8" Guides

67N34807N35038N4674

D343/1693 Industrial Cylinder HeadReference # 4N6765 6 9S0003

5M3600

REMANUFACTURED DIESEL ENGINE CYLINDER HEADS

CATERPILLAR

1


D346A Industrial Cylinder HeadReference # 7M4915 8 5M6800

D346B Industrial Cylinder HeadReference # 7N9297 8 7N9295

D348 Industrial Cylinder HeadReference # 7N9532-5S5137 12 7N9540

8S3900

D353Early


Non-Spacer Plate6 8N4232

D353Late


Spacer Plate6 7N3031

D379 Industrial Cylinder HeadReference # 7L0138 8 4L3800

D398 Industrial Cylinder HeadReference # 7L0138 12 6L7200

D399 Industrial Cylinder HeadReference # 5N8319 16 5N5280

3116 REF# 7E4204, 101-3252, 119-2968 6 101-4570

3126 REF# 157-8376 3 VALVE98' ON HIGHWAY 6 133-3734

3176 REF# 101-2067, 144-2961Fits Early serial #'s: 2YG, 7LG, 43Z1 6 9Y6678

3176B REF# 101-4004, 133-7051, 144-2966 6 104-3844

3204DI Industrial Cylinder HeadReference # 9N3111 4 9N1107

9N2362

3204PC Industrial Cylinder HeadReference # 9N0320 4 9N0275

3208 Natural Aspirated, Direct InjectionSerial # 32Y Ref # 51Z 8

2W71659N23629N5215

3208T Turbo, Serial # 2Z Dual Valve Spring 81W15872W71659L7230

3304 Early Style Non Spacer PlateReference # 4N7444 4

6N80162P64846N8874

3304PC Reference # 8N1188Spacer Plate 4 7N8514

NEW 3304PC Call for price & availability 4 7N8514

3304DI Reference # 1N4304 4 7C39047C4004

NEW 3304DI Call for price & availability 4 7C39047C4004

3306 Early Style Non Spacer PlateReference # 4N7446 4 2P6487

6N8888

3306PC Reference # 8N1187Spacer Plate 6

1W53207N85268N1446

NEW 3306PC Call for price & availability 61W53207N85268N1446

REMANUFACTURED DIESEL ENGINE CYLINDER HEADSCATERPILLAR CONTINUED

2


3306DI Reference # 8N6796 6 7N88567C3906

NEW 3306DI Call for price & availability 6 7N88567C3906

3406A Reference # 4N2260PC- Engine 6

7N13004W51707W0008

NEW 3406A Call for price & availability 67N13004W51707W0008

3406BReference # 4W2436 7W2203

Direct Injection6

7W00067W00097W2200

NEW 3406B Call for price & availability 67W00067W00097W2200

3406C Reference # 6I3598 6 110-5100

G3406 Reference# 115-2362119-6460, 110-5093 6 110-5100

3406E Reference # 4P5052122-7026, 122-8042 6 4P1599

3408A Reference # 4N1817, 7N0858PC - Engine 8

4N03516N99767N08557W1708

3408B Reference # 7W2225Direct Injection 8 7W2222

3412A Reference # 7N0848PC - Engine 12 7N0845

3412B Reference # 7W2243Direct Injection 12 7W2242

7W2204

6B


855-NTC855 series

Big CAM I, II, IIIO.E.M. 3008100RX

6 3041991

855-NTCPremium

855 series/ New Stellite ValvesBig CAM I, II, III

O.E.M. 3008100RX6 3041991

855-BC IVEarly

Big Cam IV-NTC 400Old Style Casting Large Springs 6 3041991

855-BC IVLate

Small Exhaust Port, 3/8 Injector Hold DownStandard Valve Spring

O.E.M. 3055098RX

6 3046760

REMANUFACTURED DIESEL ENGINE CYLINDER HEADSCATERPILLAR CONTINUED

CUMMINS

3


855-BC IVLate

NTC 444

Small Exhaust Port, 3/8 Injector Hold Down

Large Valve SpringO.E.M. 3050419RX

6 3046760

88-NTCBC IV

Same as NTC 444 withRecessed Valve Seats

O.E.M. 3053346RX6 3046760

91N14Scalloped Combustion FaceHorizontal Exhaust Mounting

O.E.M.3406737RX6 3055288

94N14

Recessed Valve SeatsSpecify Horizontal, Vertical, orUniversal Exhaust Mounting

30 Degree SeatO.E.M. 3406739RX

6 3078360

96N14

Recessed Valve SeatsSpecify Vertical or Universal

Exhaust Mounting45 Degree Seat

O.E.M. 3406742RX

6 3078360

4B 3.9 Liter 4 39025213916412

NEW 4B Call for price & availability 4 39025213916412

6B 5.9 Liter 6 39045733910276

NEW 6B Call for price & availability 6 39045733910276

6C Pre ' 91 O.E.M. 3913111 RX21" Air Intake 6 3911286

3904688

6C '91 & Up O.E.M. 3802259 RX16 " Air Intake 6

392105139212473921050

L10 (88) Dual Valve SpringsO.E.M. 4003970RX * 3401527RX

30332273055721

L10 (91) Single SpringO.E.M. 3073514RX * 4003980RX 3883525

M 11 Reference # '94-4003988RX '95-4004086RX 6 3084652

C-160/180/190 BM74486AR11768 6 143561

143551

NH220-743 BM60941RX Thick Intake Valves(same thickness as exhaust) 142020

NH220-743 BM60971RX Thick Intake Valves(eight stellite inserts) 142023

V352-378 Old Style AR60776RX 153143

V352-378 New Style 3275450RX 3275444

V740 / V504 Old Style AR60769RX 157782

V740 / V504 New Style 3275451RX 3275471

V555 / VT225 Old Style AR61110RX 553637

V555 / VT225 New Style 3275452RX (Natural) 3275453RX (Turbo) 3275442

CUMMINSREMANUFACTURED DIESEL ENGINE CYLINDER HEADS

4


V903 / VT903 AR11171RX 180100180102

V / VT1710 Old Style Wet AR11742RX 133570

V / VT1710 New Style Wet 3052847RX(Fuel Drillings) 133577

V / VT1710 New Style Dry 3052177RX 133576

V / VT1710 New Style Dry AR11745RX(Fuel Drillings) 133573

KT / KTA19Standard

Reference # 3604153RX 3811988RX

NOT for marine or constant speed applications

30090883081064

KT / KTAPrem 1*2

Reference # 3811985 RXTribaloy Intake Valve Seat,

Inconel Exhaust Valve3081064

KT / KTA38KT50 STD

Reference # 3021692RX 3811988RX

NOT for Marine or Constant speed applications

3007207205015

31766193081064

KT / KTA38KT50

Prem 1&2

Reference # 3811985 RXTribaloy Intake Valve Seat,

Inconel Exhaust Valves3081064

MODEL DESCRIPTION CYL Core Code

3035961 RX Rocker, Upper BC/SC(J-Brake) 3035961 D

3071453 RX Rocker, Upper 88NT(C-Brake) 3071453 D

MODEL DESCRIPTION CYL Core Code

3081251 RX BIG CAM--CAM FOLLOWER(3036939)

3018584301688730000983010158

REMANUFACTURED DIESEL ENGINE CYLINDER HEADSCUMMINS

REMANUFACTURED ROCKER BOXES

REMANUFACTURED CAM FOLLOWERS

CUMMINS

CUMMINS

5

60 Series


3-53 / 6V53 Reference # 5198203 6 5135029

NEW 3-53 / 6V53 Call for price & availability 6 51350294-53 / 8V53 Reference # 5198202 4 5134294

NEW 4-53 / 8V53 Call for price & availability 4 5134294

2-71 Reference # 5189858 2

3-71 Reference # 5198218 6 51136254-71 Reference # 5198218 8 5117438

6-71 / 12V71 Reference # 5198219 12 5109548

3-71 / 6V71 Reference # 5102769 6 5117107

4-71 / 8V71 Reference # 5102771 8 5117433

6-71 / 12V71 Reference # 5102770 12 51174355144161

6V92 Reference # 5149877 6 51485438V92 Reference # 5149878 8 5148542

149 Series Reference # 8924760 301755

8.2 Series 8922929 8 8922747

60 Series 11.1 Liter or 12.7 Liter 6 89298728929620

71 Series 4 Valve

92 Series 4 Valve

149, 60, 8.2 Series

53 Series 4 Valve

71 Series 2 Valve

DETROIT DIESEL


6

6.2/6.5


6.2 86-91 6.2 liter 8

1405729914077162140289011013716210137567

NEW 6.2 Call for price & availability 8

1405729914077162140289011013716210137567

6.5 94-96 6.5 liter 8 10137567

NEW 6.5 Call for price & availability 8 10137567

4BD1-T

MODEL DESCRIPTION CYL CASTING ID4BD1 86-91 4 5-107-0

4BD2 92-98 4 8-453-1

NEW 4BD2T Call for price & availability 4 8-453-1


GM

ISUZU

7

6.9


DT360 680392C91 6 1810075C675542C-1

DT466B 6 688833C1DT466C

(New Generation) Specify 3/8 or 5/16 Valve Guide 6 1818504C11822363C1

DT 466E 6 1823914C51827118C2

6.9 1983 -1987 8 1805296-C11805855-C1

7.3 1988 -1995 8 1808030-C1

NEW 7.3 Call for price & availability 8 1808030-C19.0 1978 - 1985 8 489097-C94

E7


675 2 Valve HeadHorizontal Exhaust Manifold 6 732GB4383X

6762 Valve Head

Vertical Exhaust Manifold(can be used w/ horizontal exhaust)

6 732GB4397X

E6 4 Valve Head (All E6) 6 732GB3424X

E7 4 Valve Head (Non E-Tech) 6 732GB3452MX

E7- E - Tech Pushrod Tube Holes are on a 5˚ anglevalves are different than STD E7 8 732GB3485MX

E9 1000 Series 732GB3421

For information on additional availability & pricing please call 1-800-480-1499


INTERNATIONAL / NAVISTAR

MACK

8

Authorized Engine Parts Supplier#1 Source for Quality Diesel Engine Components

Engine Overhaul Kits

Turbo Chargers

Fuel Injectors

Oil Coolers

Connecting Rods

Valves Int./Exh.

Diesel Crankshafts

Lube Oil Pumps

Water Pumps

Camshafts

Vibration Dampners

Aftercoolers

Caterpillar

Cummins

Detroit Diesel

International

Mack

Komatsu

Isuzu

Case

GM

Ford

John Deere

Wankesha

Navistar

Perkins

Nissan Industrial

Iveco

Fiat Allis

Allis-Chalmers

*All Manufacturers names, symbols & descriptions are used for reference purpose only and does not imply that any part listed is the product of these manufacturers.

If you don't see it here... Call us at 1 800-480-1499

www.AllianceDET.com

Thermal Cast®

Technology designed to restore out of tolerance

components, back to Original Equipment Specifications

Low cost solution

Cold process under 200° F

No pre or post heating

No induced material stress

Superior bond strength

High deposition rate

Extended core life

Engine blocks

Cylinder heads

Crankshafts

Pump housing

Flywheels

Shafts

Bearing surfaces

and many more...

Benefits:Benefits:

Applications:Applications:

AALLLLIIAANNCCEE RREEMMAANNUUFFAACCTTUURRIINNGG,, IINNCC..

WARRANTY POLICY AND REMANUFACTURED CYLINDER HEADS

The limited warranty policy of Alliance is as follows:

1. Alliance expressly warrants that its unit will, when shipped by us to the original purchaser, be free from defects in material and workmanship. This express warranty shall apply only to cylinder heads with NEW components, which are properly installed and maintained in the type of vehicle which has been prescribed for their use, and in which defects in material and workmanship shall appear within 12 months of purchase date. Cylinder heads with RECONDITIONED components will carry a warranty for six months. Bare cylinder heads are warranted on castings only. Loaded cylinder heads are warranted for the casting and loaded components.

2. Alliance's obligation under this express warranty shall extend only to the repair or replacement, at our option, of

any part or parts of any unit which has been returned to us, transportation charges prepaid, with a written statement of the reason therefore, promptly after any claim of breach of warranty shall arise, and which upon examination by us, shall appear to have been defective in material and workmanship. In lieu of such repair or replacement, this company may, at its option refund to the person having the benefit of this warranty the amount such person shall have paid for the unit. Under no circumstances will Alliance be liable for any consequential or incidental damages including claims for labor charges, transportation and loss of revenue. Replacement of cylinder head and labor will be according to OEM flat rate guide.

Warranties implied by law shall also apply to each unit but only for such time as the foregoing express warranty shall apply to that unit. The factory's obligation with respect to a breach of any implied warranty shall be the same as in the case of a breach of the foregoing express warranty. EXCEPT FOR THE EXPRESS WARRANTY STATED ABOVE AND FOR SUCH LIMITED IMPLIED WARRANTIES, THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR PURPOSE, WHICH SHALL APPLY TO ANY UNIT AND THE FACTORY HEREBY DISCLAIMS ANY AND ALL SUCH OTHER WARRANTIES.

The obligations of the factory shall not exceed beyond the obligations undertaken above. THE FACTORY SHALL HAVE NO LIABILITY OR RESPONSIBILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Any action based on any breach of any of the said warranties shall be presented within 12 months after cause of action therefore accrues. Any action brought thereafter shall be barred- if any unit shall be disassembled, modified, or otherwise tampered with, all the foregoing warranties shall lapse and become null and void. Every cylinder head is fitted with an overheat sensor. If the sensor has dissolved, been removed, or tampered with, in any way, all warranties are null and void. The laws of Pennsylvania shall govern this Limited Warranty.

NO PERSON IS AUTHORIZED BY THE FACTORY TO AGREE ON ITS BEHALF TO ANY MODIFICATION OF THE FOREGOING.

3. All units sent for Warranty/Defect must be tagged using Alliance Warranty Claim Tag and have an RGA number

assigned. All defective cylinder heads must be returned unclean. The cylinder head must be shipped as junk parts by transportation services.

4. No warranty credits will be issued until a complete analysis of unit is performed by Alliance's Quality Control

Department.

5. Account pays inbound freight. Freight will be reimbursed if unit is found to be defective.

6. Any units returned to Alliance for Warranty/Defect that have not been remanufactured by Alliance will be returned to account. Every effort will be made to return unit in the same box and condition that it was received, although this cannot be guaranteed, in the most efficient manner.

Any deviation from this policy must be approved by Alliance Sales Department.

7. As stated above, any Alliance units sent in for Warranty Defect that upon inspection are found to have been

tampered with, altered, disassembled, modified Or damaged during Installation will render the unit null and void of all warranty provisions.


FREIGHT POLICY

The following Freight and Shipping Policy pertains to all Alliance shipments:

1. Freight is prepaid by Alliance on all orders of $5,000 net exclusive of core charges. (See chart for average costs and unit requirements for freight prepaid.). See freight policy.

2. Freight on core returns is reimbursed by Alliance when returns exceed 1000 lbs.

Accounts should return cores to: Alliance Remanufacturing, Inc. Attn-. Core Department 450 E. Luzerne St. Philadelphia, PA 19124

See chart for designated freight carriers. Current carriers authorized by Alliance and areas covered are NEW PENN TRANSPORT - CONWAY - ROADWAY EXPRESS

3. Freight to Hawaii, Puerto Rico, Canada and other export markets will be shipped in most efficient and cost

effective manner. Alliance will designate carrier.

4. Failure to use Alliance authorized carriers or meet weight requirements will result in charge back to customer for freight charges.

5. Alliance does not receive freight shipments that are sent C.O.D.

6. All returns to Alliance should include:

- Account Name and Address - Account Packing Slip - Quantity of Units Returned - RGA number listed on paperwork for tracking

7. All orders sent to Alliance will be shipped with backorders held- No backorders will be canceled unless

Alliance is notified in writing or it is stated on P.O.

8. All orders will be palletized and shrink wrapped. Accounts not wanting units palletized should contact Alliance's Customer Department.

9. All returns to Alliance of cores and warranty units should be returned CLASS 50.

10. All shipments should be sent to:

Alliance Remanufacturing, Inc. 450 E Luzerne St. Philadelphia, PA 19124


CORE POLICY The following is Alliance's Core Policy and Procedure information: 1. Core credits will be issued only on cores taken in from the sale of Alliance units. 2. Only as many units as purchased may be returned for credit. Example-. If 200 units are purchased, up to 200 old

units may be returned for credit. Units should be of the same type and configuration. 3. Dollar value on core credits may not exceed dollar value on cores purchased. Example: If $200 cores are

purchased, up to $200 core credits will be allowed. 4. Only units that are received as a result of the sale of our rebuilds may be returned for credit. Please do not obtain

old cores from other sources. This policy helps maintain properly balanced inventories. Only identical exchange units will be accepted for credit.

5. The total quantity of core value of old units acceptable for core credit is limited to the total quantity of core value

of units purchased on outright basis during the previous twelve-month period. All claims for shortage must be made within 5 days after receipt of merchandise.

6. Excess customer units will be listed in a core bank these units will be used against future purchases or may be

claimed by customer within one year. All units in our possession after one year are considered property of the factory.

7. Credits are issued against current price sheets, and may only be liquidated by a merchandise purchase. 8. Cores sent back that are not acceptable will receive reduced value or no core value. (See Core Checklist for

devaluation causes by product). 9. Any units returned will be treated as cores, unless, noted on account paperwork. 10. Alliance will not be responsible for units lost in transit. Credit will be given for units received, checked in and

verified by Alliance Core Department. Any shortage claims resulting from transit problems are the responsibility of the returning account to make a claim against trucking company.

11. Core credits for less than full value will not be returned to account, unless request is made in writing and on file

with the Alliance Core Department. Core deductions will be taken according to the following

a. Calipers – ½ Core value for damaged/broken casting. Missing pistons. b. Engine Heads – No core deductions. A core that is damaged beyond repair will not be accepted.

12. All cores must be returned in original box. RGA is required for all core returns. 13. Freight is prepaid on 1000 lbs. of cores. Core returns should be listed as Class 50 on shipping documents. (See

Weight Chart and Authorized Carrier Chart in Section E - Shipping Policy.) 14. Account should attempt to list all cores returned with Alliance part numbers and group the same numbers

together. However, it should be noted that Alliance will identify units with exact part number at time of check in. 15. No customer should make a deduction for core credit from statement prior to Alliance's issuance of credit memo.

Alliance will make every effort to issue core credit within 15 days of receipt.

Documents

Diesel Cylinder Heads & Engine Accessories - SeekPartfile.seekpart.com/keywordpdf/2011/5/13/201151314549739.pdf · Diesel Cylinder Heads & Engine Accessories ... Big Cam IV-NTC 400