Diagram(s) and/or PartsList(s) · 2012. 2. 15. · 27 50017 0 ARM-CONTROL ZP (Neutral stop) 28 9811 0 NUT-LK 1/4-20 29 9798 BOLT-HH 1/2-13 X 2.5 ZP(Reverse adjustment) 0 30 50020

50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 1 of 17BOLO TINE & WHEEL ASSEMBLIES

www.mymowerparts.com

For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983

50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 2 of 17BOLO TINE & WHEEL ASSEMBLIES

Ref # Part Number Qty DescriptionS/P/F1 9711 SCR-HH 3/8-16X1.0 G5 ZP (Tine mounting)02 50049-02 TINE-BOLO LEFT SINGLE0 S3 9913 WASHER-LK .375 @ DEPL (SEE

ILLUSTRATION)0 F

4 9802 NUT-HEX 3/8-16 ZP05 50049-01 TINE-BOLO RIGHT0 S6 9555 BOLT-HH 3/8-16X1.75 G8 ZP (Tine holder to

tiller shaft)0

7 9807 NUT-H/LK 3/8-1608 1900 KIT-TINE & HOLDER 16 Tines, assembled.0 F9 50046 TINE HOLDER-WELD (FOR Bolo Tines, LT

and RT sides)0

1901 TINES-BOLO JUNIOR/TUFFY0 S/F10 9355 PIN-QUICK RELEASE (Wheel hub to shaft)011 50045-01 ASSM-TIRE&WHL LH GRAY0 F12 50045-02 ASSM-TIRE&WHL RH GRAY0 F



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 3 of 17ENGINE, BELT & CARB GUARD



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 4 of 17ENGINE, BELT & CARB GUARD

Ref # Part Number Qty DescriptionS/P/F1 9707 SCR 5/16-24 X 102 9912 WASHER-LK .312 ZP03 9901 WASHER-.88X312X.08 ZP04 9797 BOLT-HH 3/8-24 X .75 ZP05 9913 WASHER-LK .375 @ DEPL06 50024 DISC-REV07 50022 PULLEY-ENG MACH08 9302 KEY-.188 SQ X 1.2509 1138-1 SHIM-1.0X.7656X.0620 S

10 0 ENGINE - TECUMSEH INDIVIDUAL ENGINE PARTS FOR YOUR TILLER'S ENGINE ARE NOT LISTED IN THIS CATALOG. ENGINE PARTS ARE AVAILABLE FROM YOU LOCAL TECUMSEHENGINE SERVICE OUTLET (LOOK IN THE YELLOW PAGES UNDER "ENGINES-GASOLINE."

0

10 0 ENGINE - STANDARD RECOIL START IF YOU CANNOT OBTAIN ENGINE PARTS LOCALLY, PLEASE CONTACT THE OWNER SERVICE DEPARTMENT HERE AT THE TILLER FACTORY. YOUR ENGINE IS COVERED BY THE ENGINE MANUFACTURER'S LIMITED WARRANTY FOR ONE FULL YEAR

0

10 0 ENGINE - 3.5 HP, MODEL H35, AFTER THEDATE YOU RECEIVED YOUR TILLER. DURING THIS TIME, ANY REPAIR WORK SHOULD BE PERFORMED BY THE ENGINEREPAIR DEALER WHO IS AUTHORIZED BYTHE MANUFACTURER TO REPAIR YOUR MAKE OF ENGINE.

0

10 0 ENGINE - TYPE 45564N FOR FURTHER DETAILS ON THE ENGINE MANUFACTURER'S LIMITED WARRANTY, PLEASE SEE THE ENGINE OWNER'S MANUAL THAT CAME WITH YOUR TILLER.

0

11 50028 BELT-V012 50122 BELT SHROUD W/DECAL013 50082 DECAL-BELT COVER014 50068 CLIP015 9822 NUT-WING/LK 1/4-20 ZP016 9759 SCR-HH 5/16-18X1.75017 9801 NUT-HEX 5/16-18 ZP018 50026 PAD-ENG JACKING019 50097 GUARD-CARBURETOR PNT020 9720 BOLT-HH 5/16-18X2 ZP0



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 5 of 17FORWARD/REVERSE SHIFT & ENGINE MOUNT




Ref # Part Number Qty DescriptionS/P/F1 9710 SCR-HH 3/8-16X1.0 G5 ZP0 F2 9913 WASHER-LK .375 @ DEPL (See Illustration,

used in two places.)0

3 9903 WASHER-1.0X.438X.104 ZP04 50060 PLATE-HANDLEBAR ADJUST0 F5 9705 SCR-HH 5/16-18X1.25 G5ZP (Handlebar

attachment bracket to transmission cover.)0

6 9912 WASHER-LK .312 ZP (See Illustration, used in three places.)

0

7 50051 BRKT-HANDLEBAR PIVOT0 F8 9711 SCR-HH 3/8-16X1.0 G5 ZP (Bracket to

handle bars.)0

9 50061 WASHER-TAB #010 9837 NUT-LOCK 3/8-16 NYLON ZP0 S11 9704 SCR-HH 5/16-18X1.0 G5 ZP (Front cover to

tranmission case)0

12 9904 WASHER-FLAT 3/8 SAE0 S13 50025 BUSHING-.5X.375X.375 (Engine mount

arms)0

14 50031 COVER-TRANS MACH015 9727 PLUG-PIPE 3/8 NPT (Gear oil fill hole)0 S16 9556 SCR-SH 5/16-18 X .5 ZP (Eccentric arms to

engine mount arms)0

17 50014 ROLLER-ECC (Eccentric arms)018 9354 PIN-ROLL .188 X 1 (Eccentric arms to

eccentric shaft)0

19 50123 ECC W/SPG & ROLL PIN-RT (Inc. #18 & 26)020 1440 WASHER # .875 X .65 X .06 (Eccentric shaft)0 S21 50012 SHAFT-ECC MACH (Eccentric)022 50125 ECC-LT MACH (Inc. #18)023 9734 SCR-HH 1/4-20X1.0 ((Eccentric arm to

neutral control stop arm)0

24 9900 WASHER-FLAT 1/4 SAE025 50018 BUSHING-.406X.255X.595 (Neutral Control

Arm)0

26 50096 SPRING-.56 X .4 ZP(Neutral Control Arm FOR S/N 1274 & LATER, DO NOT USE 26A)

0

26A 50019 SPRING-.56X.4 ZP(FOR S/N 1273 & EARLIER, DO NOT USE 26)

0

27 50017 ARM-CONTROL ZP (Neutral stop)028 9811 NUT-LK 1/4-20029 9798 BOLT-HH 1/2-13 X 2.5 ZP(Reverse

adjustment)0

30 50020 SPRING-.685X1.75 (Reverse adjustment)031 9905 WASHER-PLAIN 1/2 ZP032 9836 NUT-LOCK 1/2-13 NYLON INSERT ZP0




Ref # Part Number Qty DescriptionS/P/F33 50124 BRKT-ENG MTG W/DECAL (Inc. 39 & two

#34)0

34 9310 PIN-SPIROL .25 X 2.5035 9707 SCR 5/16-24 X 1 (Engine mount to engine)036 9901 WASHER-.88X312X.08 ZP037 9558 BOLT-HH 3/8-16X1.5 FTH ZP (Belt

adjustment)0

38 9802 NUT-HEX 3/8-16 ZP039 50112 DECAL-BELT WARNING (Not Illustrated)0



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 8 of 17HANDLE BARS, SHIFT & THROTTLE



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 9 of 17HANDLE BARS, SHIFT & THROTTLE

Ref # Part Number Qty DescriptionS/P/F1 1100808 SCR-HH 5/16-18X1.25 G5ZP02 1100242 WASHER-LK .312 ZP0 S3 50051 BRKT-HANDLEBAR PIVOT04 1100046 SCR-HH 3/8-16X1.0 G5 ZP0 S5 50061 WASHER-TAB #06 9837 NUT-LOCK 3/8-16 NYLON ZP0 S7 50060 PLATE-HANDLEBAR ADJUST08 1100046 SCR-HH 3/8-16X1.0 G5 ZP0 S9 1100243 WASHER-LK .375 @ DEPL0 S

10 9903 WASHER-1.0X.438X.104 ZP011 50181 ASSM-HANDLEBAR REPLACE0 F12 50062 ASSM-CLAMP0 F13 9338 PIN-CLIP .080 S14 50108 ASSM-DRIVE CONTROL ROD015 9208 KNOB-DRIVE CNTRL ROD016 9471 GRIPS-HANDLEBAR017 50194 DECAL-CONTROL PANEL018 9211 GROMMET-PLASTIC019 9202 TIE-RED0 S20 50118 CABLE-THROTTLE & KNOB0 S/F21 9212 KNOB-THROTTLE CABLE0 S22 1114748 SCR-RH M10-32X.5 MACH0 /P23 1100240 WASHER-LK M100 /P24 1186208 NUT-HH M10-32X.1250 /P



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 10 of 17HOOD & DEPTH REGULATOR



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 11 of 17HOOD & DEPTH REGULATOR

Ref # Part Number Qty DescriptionS/P/F1 9119 KNOB-CONTROL (INCLUDES RETAINING

RING)0 S

2 9120 RING-TOLERANCE .5325 ID0 S3 50119 REGULATOR-DEPTH W/KNOB04 1100046 SCR-HH 3/8-16X1.0 G5 ZP0 S5 1100243 WASHER-LK .375 @ DEPL0 S6 1186231 NUT-HEX 3/8-16 ZP0 S7 50058 SHOE-DEPTH REGULATOR08 9726 PLUG-PIPE 1/4 NPT0 S9 1120 SPRING .406 X 1.250

10 1119 PLUNGER011 50120 ASSM-REAR HOOD BRKT (INCLUDES

ROLL PIN)0

12 9552 SCR-HWH 1/4-20 X .5 STH0 S13 1100044 SCR-HHC 5/16-18X.75 GR 5 ZP0 S14 1100242 WASHER-LK .312 ZP0 S15 50182 ASSM-HOOD W/DECALS016 9553 SCR-HWH 5/16-18 X .5 STH0 S17 50098 DECAL-TB JR LOGO018 50193 DECAL-OPER INST0



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 12 of 17MAIN SHAFT ASSEMBLY



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 13 of 17MAIN SHAFT ASSEMBLY

Ref # Part Number Qty DescriptionS/P/F1 1224-1 SHIM-1.75X1.5X.010 S/F1 1224-2 SHIM-1.75X1.5X.030 S/F1 1224-3 SHIM-1.75X1.5X.0050 S/F

1325C SHIM SET-DRIVESHAFT-HORSE0 S2 1899 KIT-DRIVESHAFT JR0 F3 50042 GEAR-WORM BRONZE MACH (Tiller Drive)0 S/F4 50041 GEAR-WORM 61 TEETH MACH (Wheel

Drive)0 F

5 50043 WASHER-#1.25X.75X.060 S6 1714 KIT-BRG CONE & RACE-DRIVESHAFT0 S/F7 50027 WASHER-SHLDR HARDENED 11/16""I.D. x

11/4" O. D. (Thrust external, hardened)0 S

8 50021 PULLEY-TRANS MACH (Transmission drive, 2 belt grooves

0

9 9356 KEY-.188 SQ X .75 (Transmission pulley to drive shaft)

0

10 50076 WASHER-.827X.331X.098011 9799 SCR-FLHH 5/16-24 X .75 ZP(Pulley to drive

shaft)0

1360A OIL (1901964) 2 QT 140WT01901964 OIL-GEAR 1 QT 140WT0



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 14 of 17TRANSMISSION HSG. & SEALS/GASKETS



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 15 of 17TRANSMISSION HSG. & SEALS/GASKETS

Ref # Part Number Qty DescriptionS/P/F1 9773 SCR-HFLK 1/2-20X.875 (Rear bearing cap

mounting)0

2 1115 CAP-REAR #1115 (Rear Bearing)03 1124-2 GASKET-BRG COVER (Front and rear

bearing caps 0.010" thick)0 S

4 9726 PLUG-PIPE 1/4 NPT (Gear oil level check and gear oil drain holes, front & rear)

0 S

5 9613 SEAL-OIL TRIPLE LIP (Tiller shaft, LT & RT side)

0

6 50078 ASSM-TRANS A UNIT (W/O covers, shaft, gears, seals, etc.)

0 F

7 9609 SEAL-OIL WHEEL SHAFT (Lt & Rt sides)08 1114 CAP (Front Bearing)09 9600 SEAL-PINION SHAFT PT/85030/00 (Main

Drive shaft, front)0

10 9701 SCR-HH 1/4-20X.75 G5 ZP (Front bearing cap mounting)

0

11 9910 WASHER-LK .25 ZP012 9550 SCR-HH 5/16-18X.5 GD5 YEL (Tiller housing

cover to case)0

13 9912 WASHER-LK .312 ZP (Used in both covers)014 50074 CVR-TRANS REAR PNT (Tiller Housing)0 S15 50032 GASKET-GEAR HSG (Transmission covers,

front & rear)0 S

16 50031 COVER-TRANS MACH (Front Transmission)0 F17 9704 SCR-HH 5/16-18X1.0 G5 ZP (Front

Transmission to cover)0

18 9727 PLUG-PIPE 3/8 NPT (Gear oil fill hole)0 S19 50051 BRKT-HANDLEBAR PIVOT (Handlebar

attachment)0 F

20 9705 SCR-HH 5/16-18X1.25 G5 (Handlebar attachment)

0

21 1898 SEAL & GASKET SET-JR (Inc. 2 #3, 2 #15, 2#5, 1 #9)

0




50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 16 of 17WHEEL & TILLER SHAFT ASSEMBLIES



50126 JUNIOR I (3.5HP)(S/N M1274-M8203) Page 17 of 17WHEEL & TILLER SHAFT ASSEMBLIES

Ref # Part Number Qty DescriptionS/P/F1 9613 SEAL-OIL TRIPLE LIP (Tiller shaft, LT & RT

Sides)0

2 9511 RING-HEAVY EXT .906 ID (Tiller and Wheel Shafts)

0 S

3 1166-1 SHIM-1.375X1.015X.0620 S/F3 1166-2 SHIM-1.375X1.015X.030 S/F3 1166-3 SHIM-1.375X1.015X.0150 S/F3 1166-4 SHIM-1.375X1.015X.010 S/F4 1086 BUSHING-1.25X1.005X1.5 bronze, (Tiller and

Wheel Shafts, LT & RT sides)0 S

5 1132-2 SHIM-1.234X1.015X.062 (Tiller and Wheel Shafts)

0 S

6 50104 TILLER SHAFT-W/KEY (Inc. 6)07 1104 KEY-WOODRUFF .25X1.12 (Tiller shaft to

worm gear)0 S

8 50042 GEAR-WORM BRONZE MACH (Tiller Drive)0 S9 9512 RING-RETAINING 5133-989 (E-type

retaining, external, LT & RT sides)0 S

10 9609 SEAL-OIL WHEELSHAFT (LT & RT sides)011 50105 WHEELSHAFT-W/KEY (Inc. 12)012 9305 KEY-HI PRO .25X1.062 (Wheel shaft to worm

gear)0 S

13 50041 GEAR-WORM 61 TEETH MACH bronze, (Wheel drive)

0




Documents

Diagram(s) and/or PartsList(s) · 2012. 2. 15. · 27 50017 0 ARM-CONTROL ZP (Neutral stop) 28 9811 0 NUT-LK 1/4-20 29 9798 BOLT-HH 1/2-13 X 2.5 ZP(Reverse adjustment) 0 30 50020