DESING TOOLS WORKSHOP – I

SEM IN LAB EXAMINATION – I

FROM 02-09-2019 TO 07-09-2019

QUESTION BANK

CO1

PART 1

PART MODELLING IN CREO PARAMETRIC

1. Draw the front view, top view and side view of the object shown in Fig.

C01 C01 C02

15 5 10

2. Draw the front view, top view and side view of the object shown in Fig.

3. Draw the front view, top view and side view of the object shown in Fig.

4. Draw the front view, top view and side view of the object shown in Fig.

5. Draw the front view, top view and side view of the object shown in Fig.

6. Draw the front view, top view and side view of the object shown in Fig.

7. Draw the front view, top view and side view of the object shown in Fig.

8. Draw the front view, top view and side view of the object shown in Fig.

9. Draw the front view, top view and side view of the object shown in Fig.

10. Draw the front view, top view and side view of the object shown in Fig.

Orthographic question

1. Draw the front view, top view and side view of the object shown in Fig.

2. Draw the front view, top view and side view of the object shown in Fig.

3. Draw the front view, top view and side view of the object shown in Fig.

4. Draw the front view, top view and side view of the object shown in Fig.

5. Draw the front view, top view and side view of the object shown in Fig

6. Draw the front view, top view and side view of the object shown in Fig

7. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

8. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

9. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

10. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

11. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

12. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

13. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

14. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

15. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

16. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

17. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

18. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

19. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the

right, of the objects shown below:

20. Draw (i) the view from the front, (ii) the view from the right and (iii) the view from the

left of the object shown below

21. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the left,

of the objects shown below:

22. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the left,

of the objects shown below:

23. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the left,

of the objects shown below

24. Draw (i) the view from the front, (ii) the view from above and (iii) the view from the left,

of the objects shown below

25. Draw the front view, top view and side view of the object shown in Fig

26. Draw the front view, top view and side view of the object shown in Fig

27. Draw the front view, top view and side view of the object shown in Fig

28. Draw the front view, top view and side view of the object shown in Fig

CO1

PART 2

QUESTIONS ON 3D PRINTING:

1. Explain about addictive manufacturing and its applications?

2. Write down different types of 3D printing technologies?

3. What is thermo plastic material and its properties?

4. Types of thermo plastic materials and their melting temperatures?

5. In detail explain various 3D printing process such as

a. FDM

b. ABS

c. SLS

6. Draw the block diagram, explaining the detail process to print a CAD model in 3D printer?

CO2

PROJECT MAPPING:

1. Explain product design and development process by using CAD/CAM approach and draw the

block diagram in Draw.io project mapping software?

2. Explain Conventional design process by using CAD/CAM approach and draw the block diagram in

Draw.io project mapping software?

3. Explain Conceptual design process by using CAD/CAM approach and draw the block diagram in

Draw.io project mapping software?