Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
1
DesignJet Tips and Tricks
Speaker’s Name: Dave SmitchgerCourse ID: GD21-3Course Outline: Various Tips and Tricks for Designjet users
Dave Smitchger
Hewlett-Packard
Response Center Engineer
Advanced Technical Support
Designjet Tips & Tricks Plus Q & A
2
designjet 430
designjet 500 / 500ps
designjet 800 / 800ps
designjet 1050c + / 1055CM + also with Multi-roll feeder
designjet 5500 / 5500ps *
designjet cc800ps
Designjet Portfolio(For Technical Market)
* New this Fall
How does WebAccess work?
TCP/IP
Type IP address of the printer into your web browser
Designjet 5000 series embedded
WebServer
3
Uses:• Driverless printing• Reprint files after changing
settings• New path for UNIX and
LINUX• Production environment• Remote printing
Designjet 5500/5500psWebSubmitter
Accepted File Formats:HP-GL/2, HP RTL CALS G4 TIFFJPEGAdobe PDF 1.3
(only in the HP DJ 5500PS)
Adobe PS (only in the HP DJ 5500PS)
Designjet 5500/5500psWebSubmitter
4
Designjet 5500/5500ps WebSubmitter(Browse Printer)
Copying .PLT files to the printer over the network
With any designjet printer that uses a jetdirect card
model number 600N, 610N or 615N, using
TCP/IP protocol, you can FTP the file to the printer
Detailed instructions at the end of this presentation
Designjet models:
500 series
800 series
1000 series
5000 series
5
Why are my plots clipping?
Why are my plots clipping?Most common reason is the non-printable area has not been taken into account.
6
Why are my plots clipping?Enter the
leading edge, trailing edge
and side margins that are list in the Users Manual of the printer.
These values are also listed at the end of this
presentation
Note: For most page sizes, the proper margins, or non-printable area, have been properly predefined
Colors are coming out different on one printer vs. another.
Print out the Color Wheel to find out your complete gamut
of colors to choose from.
The different designjet printers are designed with various inks and media types to achieve the most
optimum quality available.
7
How can I reduce the leading edge margin on my designjet 5000 series printer
Heavy ink saturation on the leading edge of the media would cause media/print head crashes.
If the margin were less, the potential for media/print head
crashes would increase substantially.
There is no way to reduce the leading edge margin unless you
use the take-up reel option.
If TUR is installed:(Printer Menu > Device Setup > TUR installed=YES)
AND(Media Menu > TUR Loaded=YES)
The Reduced Margins option is only available:
designjet 500
Designjet 500 printer
CAD or GIS
HPGL/2 Accessory Card
When using the designjet 500 printer in the CAD or GIS Environment, the HPGL/2 Accessory Card is a great
enhancement.
HPGL/2 is a very good printer language for CAD and GIS
applications.
HPGL/2 Card: C7772A
Additional Memory:
64MB C2387A
128MB C2388A
Part Numbers:
8
Designjet 10PS/20PS/50PS
Target market:Proofing
Not For CAD because there is no
HPGL/2 support
ColorPro CAD
ColorPro CADHp Business Inkjet 2600
Designjet 10PS/20PS/50PS
Use the Correct and Most Current Driver
Get the latest HP Designjet printer drivers from:
www.designjet-online.com www.hp.com
Use HP-GL/2 for AutoCAD plots.
Use Postscript for graphics & rendered Images
Call HP Customer Care Center for printer help (208) 323-2551
9
Q&A
Pick My Brain
Or
Stump the Tech
THE
MY
THE
BACKUP SLIDES
MORE
TIPS -N-Tricks
10
MODEL F/W LEVEL• 5000, 5000PS A.02.16• 1055CM A.01.13• 1050C A.01.13• 1055CM+ A.02.05• 1050C+ A.02.05• 800PS A.02.05• 800 A.02.05 • 500PS A.02.05 • 500 A.02.05• CP series A.04.08
How old is your printer’s firmware?
The designjet 500, 800 & 5000 series printers, have firmware available for
download from the HP web site.
http://www.hp.com/go/designjet
What actually happens when I select a media type on the printer?
Media N ame Print Quality # of passes Resolution Resolution (1) Carriage speed (2)Max Quality 8 600 dpi 600 dpi 40Productivity 6 300 dpi 600 dpi 40Max Speed 1 300 dpi 600 dpi 40Max Quality 8 600 dpi 600 dpi 40Productivity 6 300 dpi 600 dpi 40Max Speed 2 300 dpi 600 dpi 40Max Quality 10 600 dpi 600 dpi 40Productivity 8 300 dpi 600 dpi 40Max Speed 2 300 dpi 600 dpi 40Max Quality 8 600 dpi 1200 dpi 28.3Productivity 8 300 dpi 600 dpi 40Max Speed 4 300 dpi 600 dpi 25
Coated
Heavy Coated Economy
Heavy Coated
Glossy
(1) Enhanced resolution ON(2) All Print Modes are Bi-directional
NOTE: The print modes below are theoreticalexamples and may not reflect actual print modes.
The media type that is selected on the front panel of the printer, along with the print quality selection, will dictate the print mode the printer uses.
The following is a list of the print features that are affected:• Number of passes (media advance)
• Printing Resolution (dpi)
• Carriage Speed (cm/seconds)
• Color Maps
• Print Mask (Fault Tolerant print mode)
11
Designjet series Printing Speed Factors:
• Is the printer using the widest media that it can use?
• 42” vs. 60”?
• Rated at ft2 per hour?
• Orientation of the drawing• Short edge first vs. long edge first?
• Relative Humidity and/or Dry Time setting
• Higher humidity needs more time between swaths to dry
• Media type and Print Mode
6 0 ” C o a te d 4 2 ” C o a te d
M a x Sp e e d5 6 9 ft2/h r
5 2 .8 6 m 2/h r 0 ’ 3 6 ”
4 9 9 ft2/h r 4 6 .3 6 m 2/h r
1 ’ 1 2 ”
P ro d u c tiv ity 1 0 0 ft2/h r
9 .2 9 m 2/h r 3 ’ 3 6 ”
8 9 ft2/h r 8 .2 7 m 2/h r
4 ’ 3 6 ”
Prin
t Mod
e Se
tting
M a x Q u a lity
7 6 ft2/h r 7 .0 6 m 2/h r
4 ’ 3 6 ”
6 8 ft2/h r 6 .3 2 m 2/h r
5 ’ 5 4 ”
Short edge first Long edge first
designjet cc800ps When scanning thick media like foamcore, you must input the specific image size instead of selecting Automatic.
Why does the document that I am scanning, stop before it is complete?
Automatic will pass the document through the feeder to check the image size, but can not reverse the document feed for thick media.
12
Designjet 1000 series Multi-roll
• When installing the designjet 1000 series printer on the Multi-roll, by sure that it is completely “square” with the alignment
• 1000 series “A” version connects to the MR with the serial cable and parallel cable
• 1000 series “B” version connects to the MR with the parallel cable
• When inserting the in-feed assembly, make sure the fingers go on top of the Mylar strip. (Don’t force it)
• To test if the in-feed is in the proper position, use a piece of paper to slide in and out along the platen
Designjet 1000 series Multi-roll
13
designJet 500/800 series
Designjet Series Margins
designJet CP series
designJet 400 series
Designjet Series Margins
designJet 1000 series
designJet 5000 series
14
Procedure to FTP a file to the printer via the jetdirect network connection:
It works best if you make a Temp directory and copy your file(s) to that directory. For example, create a directory called TEMP on your C: drive and copy all of the files you want to print to the TEMP directory.
1. Get to a DOS or COMMAND prompt on your PC and type:CD\TEMP
2. Next type: FTP 192.0.0.192 (In this example 192.0.0.192 is the IP address for the printer. Be sure to use your specific IP address for your printer)
3. You should get something like the following:Connected to 192.0.0.192220 JD FTP Server ReadyUser <192.0.0.192:<none>>:
4. Press Enter and you will be prompted for a Password:
5. Press Enter without typing anything else
You will get several lines of information one of which will probably say something like:PORT1 Print to port 1 DesignJet 5000PS (C6091A)
FTP Instructoins (1 of 2)
For:designJet 500 seriesdesignJet 800 series designJet 1000 series designJet 5000 series
(STEP 5 CONTINUED)
Further down, you should see:230 User logged in.ftp>
6. At the FTP Prompt, type:PUT fname.ext (where fname is the name of the file you want to copy and ext is the file extension)
On the computer you will see 2 or 3 lines of information while it is copying and finally it should say:ftp: xxxxxxxx bytes sent in x.xxSeconds xxx.xxKbytes/sec.ftp>
You can copy more files to the printer at this point if you would like or type QUIT to exit FTP.(NOTE: If the ftp connection times out or is closed by remote host, repeat steps 2 through 5 to regain the connection)
(To quit the FTP program, type QUIT and then close the DOS window)
FTP Instructoins (2 of 2)
For:designJet 500 seriesdesignJet 800 series designJet 1000 series designJet 5000 series