DESIGN AND CONSTRUCTION GROUP THE GOVERNOR NELSON … 01 C.pdf · page 1 of 1 45306-c . design and construction group. the governor nelson a. rockefeller. empire state plaza. a. lbany,

Page 1 of 1 45306-C

DESIGN AND CONSTRUCTION GROUP THE GOVERNOR NELSON A. ROCKEFELLER

EMPIRE STATE PLAZA ALBANY, NY 12242

ADDENDUM NO. 1 TO PROJECT NO. 45306-C

REPLACE WINDOW GASKETS, WEST SIDE BUILDING 62

BUFFALO PSYCHIATRIC CENTER 400 FOREST AVENUE

BUFFALO, NY

October 27, 2016 NOTE: This Addendum forms a part of the Contract Documents. Insert it in the Project Manual.

Acknowledge receipt of this Addendum in the space provided on the Bid Form.

1. Discard DOCUMENT 000110 TABLE OF CONTENTS in the bound Project Manual and add the accompanying DOCUMENT 000110 TABLE OF CONTENTS, revised 10/14/16.

2. Add the accompanying document “Asbestos and PCB Caulk Inspection West Side Exterior Window Caulk Only” to the Project Manual APPENDIX.

END OF ADDENDUM

Margaret F. Larkin Executive Director Design and Construction

Updated 02/22/2016 REVISED 10/27/2016 000110 - 1 Project No. 45306-C

TABLE OF CONTENTS PROCUREMENT AND CONTRACTING REQUIREMENTS GROUP DIVISION 00 – PROCUREMENT AND CONTRACTING REQUIREMENTS INTRODUCTORY INFORMATION

Document Number and Title 000101 Title Page (Cover) 000105 Certification Page 000110 Table Of Contents 000115 List Of Drawings BIDDING REQUIREMENTS Document Number and Title 001114 Advertisement For Bids 002113 Instructions To Bidders 002213 Supplementary Instructions To Bidders – MWBE-EEO 002218 Supplementary Instructions To Bidders – Pre-Bid Site Visit 002219 Supplementary Instructions To Bidders – Qualifications of Bidders 003126 Existing Hazardous Material Information 004113 Bid Form 004313 Form Of Bid Bond – Bid Security 004314 New York State Surety Bond 006517 DCA-3 Offerer Disclosure of Prior Non-Responsibility Determinations CONTRACTING REQUIREMENTS Document Number and Title 007213 General Conditions 007305 Supplementary Conditions – Liquidated Damages 007307 Supplementary Conditions – MWBE-EEO 007322 Supplementary Conditions – Worker’s Compensation 007323 Supplementary Conditions – Vendor Responsibility

007324 Supplementary Conditions - Encouraging Use of New York State Businesses in Contract Performance

007326 Supplementary Conditions - Orders on Contract (Change Orders) 007327 Supplementary Conditions - Encouraging Use of Service-Disabled Veteran-Owned

Business Enterprises in Contract Performance

SPECIFICATIONS GROUP GENERAL REQUIREMENTS SUBGROUP

Updated 02/22/2016 REVISED 10/27/2016 000110 - 2 Project No. 45306-C

DIVISION 01 – GENERAL REQUIREMENTS Section Number and Title 011000 Summary Of The Work 011001 Contractor Rules and Regulations 012100 Allowances 012200 Cost Computations 013000 Administrative Requirements 013113 Project Schedule 013119 Project Meetings 013300 Submittals 014100 Regulatory Requirements 014339 Mockup Requirements 015000 Construction Facilities & Temporary Controls 016500 Materials And Equipment 017329 Removals Cutting And Patching 017716 Contract Closeout FACILITY CONSTRUCTION SUBGROUP DIVISION 07 – THERMAL AND MOISTURE PROTECTION Section Number and Title 079200 Joint Sealers DIVISION 08 – OPENINGS Section Number and Title 085113 Aluminum Window Gaskets APPENDIX BDC-328 Utilization Plan BDC-329 Contractor's List of Subcontractors-Suppliers BDC-406 Summary of Special Inspections

Asbestos and PCB Caulk Inspection West Side Exterior Window Caulk Only Prevailing Rate Case Schedule of Submittals (SOS)

END OF TABLE OF CONTENTS

New York State Certified Women Business Enterprise (WBE)

December 4, 2015 Hamilton Houston Lownie Architects Mr. Manuel Rivera 172 Allen Street Buffalo, New York 14201 Re: Pre-Renovation Asbestos and PCB Inspection Buffalo Psychiatric Center 400 Forest Avenue Buffalo, New York 14213 Strozzi Building West Side Exterior Window Caulk Only Dear Mr. Rivera: Enclosed please find a copy of the Asbestos & Lead-Based Paint Inspection Report for the above referenced property. The scope of work for this project was limited to client defined materials including window caulking and sealant materials located on the west side of the Buffalo Psychiatric Center’s Strozzi Building. If after reviewing this report you have any questions, or if we can be of assistance in any other way, please do not hesitate to call. Thank you for the opportunity to be of service to Hamilton Houston Lownie Architects. Sincerely, MS Analytical, LLC

Tony Franjoine, Jr.

Asbestos and PCB Caulk Inspection West Side Exterior Window Caulk Only

of

Buffalo Psychiatric Center 400 Forest Avenue

Buffalo, New York 14213 Strozzi Building

Prepared for

Hamilton Houston Lownie Architects

Prepared by

Conditions as of November 20, 2015

SUMMARY TABULATION

I. Asbestos Inspection 1.1. Introduction 1.2. Executive summary 1.3. Purpose 1.4. Methodology

II. PCB’s in Building Caulks and Sealants

2.1. Introduction 2.2. Background 2.3. Methodology 2.4. Inspection Report 2.5. PCB Analysis Report APPENDIX

A. General conditions of inspection B. Certifications and licenses C. Laboratory report and chain of custody

SECTION 1.0 Asbestos Inspection 1.1 Introduction MS Analytical was retained by Hamilton Houston Lownie Architects to inspect the windows caulking and sealant materials on the West Side of the Buffalo Psychiatric Center’s Strozzi Building located at 400 Forest Avenue in Buffalo, New York for the presence of materials suspected of containing asbestos (ACBM). MS Analytical was charged with:

* locating suspect asbestos containing materials, * sampling of these materials to ascertain asbestos content, and * identifying the locations and estimated quantities of the confirmed asbestos containing

materials. The information following this introduction details the amount of asbestos present in this facility and the location of the ACBM (asbestos containing building materials). Although the report is a comprehensive analysis of the asbestos inspection work performed, it would be helpful to review all applicable federal, state and local rules, laws and regulations regarding the handling and treatment of asbestos containing building materials (ACBM). The following is a list of suggested reading and information sources relating to asbestos: * New York State Department of Labor Industrial Code Rule 56 * National Emission Standard for Hazardous Air Pollutants (NESHAPS)

Occupational Safety and Health Administration (OSHA 1926.1101, 1910.134, 1910.1020, 1910.1200, 1910.145, 1910.95, 1926.58)

* Environmental Protection Agency rule CFR 763.46 Asbestos Hazard Emergency

Response Act

1.2 Executive Summary The scope of services included the identification of suspect asbestos containing building materials in areas of planned renovations; sampling and analysis of the suspect materials; and identifying the locations and estimated quantities of the confirmed asbestos containing materials. The inspection was conducted on November 20, 2015 and revealed the following suspect asbestos containing building materials (ACBM). HAN # Material Description

600 Window Caulk - New Soft Gray

601 Window Caulk - Bottom Layer Soft Silver

602 Window Module Surround Caulk - Soft White

603 Window Glazing Compound - Black

Sampling and analysis of the suspect materials under Polarized Light Microscopy, and where necessary under Transmission Electron Microscopy, revealed the following:

All samples collected on the date of inspection were determined to NOT contain asbestos by laboratory analysis.

1.3 Purpose The purpose of the asbestos inspection was to identify and quantify the types of asbestos containing building materials (ACBM) in the building. Samples of the suspect materials were collected for analysis by an independent laboratory, and the condition of each material noted in relation to its potential to be disturbed. The potential for fiber release was also considered. The report is generated for the exclusive use of Hamilton Houston Lownie Architects and its representatives or agents, and is not designed to serve as a specification for abatement. 1.4 Methodology for inspection All work performed by MS Analytical was conducted in accordance with applicable regulations including New York State Department of Labor standards 12 NYCRR Part 56, National Emission Standards for Hazardous Air Pollutants (NESHAPS), and Occupational Safety and Health Administration regulations 29 CFR 1910.1101 and 29 CFR 1910.134. All MS Analytical personnel assigned to conduct inspections have completed the Environmental Protection Agency (EPA) required training and New York State Department of Labor Division of Safety and Health certification program. Each suspect asbestos containing building material (ACBM) was assigned a HOMOGENEOUS AREA NUMBER (HAN). Homogeneous areas are materials of like composition, color (in some instances), texture and appearance. As an example, homogeneous area #600 is Window Caulk – New Soft Gray.

1.4 Methodology for inspection (Continued) Based on the homogeneous areas, samples of suspect materials were collected. Techniques used for sample collection were designed to minimize damage to suspected areas, reduce any potential for fiber release, and ensure the safety of the inspector and building occupants. Samples were collected by MS Analytical using the following procedures:

1. The surface to be sampled was sprayed with amended water (detergent and water) as necessary

2. A plastic sample bag was held to the surface sampled

3. The sample was collected using tools appropriate to the friability of the material sampled

4. Sample bags were labeled with a unique sample identification number

5. Samples were recorded on a Chain of Custody form, and submitted under strict chain-

of-custody procedures to an ELAP and NYSDOH approved and certified laboratory for analysis

Samples were first analyzed using PLM, Polarized Light Microscopy in accordance with US Environmental Protection Agency Interim Method, 40 CFR Pt 763, Supt F, App A(7-1-87). For the sample results not considered definitive, additional analysis was performed under Transmission Electron Microscopy (TEM) in accordance with NYS DOH ELAP Item #198.4, for Non-friable Organically Bound Bulk Material (NOB). The results of this analysis confirmed whether or not a suspect materials actually contained asbestos. The confirmed materials are listed in SECTION 1.2 Executive Summary.

Section 2.0 PCBs in Caulk Sampling

2.1 Introduction MS Analytical was retained by Hamilton Houston Lownie Architects to inspect the windows caulking and sealant materials on the West Side of the Buffalo Psychiatric Center’s Strozzi Building located at 400 Forest Avenue in Buffalo, New York for the presence of caulking/sealant materials suspected of containing Polychlorinated Biphenyls (PCBs) that may be impacted by planned renovations. MS Analytical was charged with:

1. locating suspect materials, 2. bulk sampling of caulking/sealants for lab analysis to determine PCB content. 3. submission of samples to and independent certified laboratory, and preparation of

a summary report 2.2 Background PCBs are mixtures of synthetic organic chemicals with the same basic chemical structure and similar physical properties ranging from oily liquids to waxy solids. Due to their non-flammability, chemical stability, high boiling point and electrical insulating properties, PCBs were used in hundreds of industrial and commercial applications including electrical, heat transfer, and hydraulic equipment; as plasticizers in paints, plastics, rubber and caulking products; in pigments, dyes and carbonless copy paper and many other applications. More than 1.5 billion pounds of PCBs were manufactured in the United States prior to cessation of production in 1977. Concern over the toxicity and persistence in the environment of Polychlorinated Biphenyls (PCBs) led Congress in 1976 to enact 6(e) of the Toxic Substances Control Act (TSCA) that included among other things, prohibitions on the manufacture, processing, and distribution in commerce of PCBs. The following is a partial listing of applicable regulations regarding proper handling and disposal:

New York State Department of Environmental Conservation - 6 NYCRR Part 371

* USEPA 40 CFR Part 761.62 Disposal of PCB Bulk Product Waste

2.3 Methodology MS Analytical collected samples of at least 10g of Caulk/Sealant. Samples were recorded and handled according to strict chain-of-custody protocol sample sizes and submitted to an independent certified laboratory for analysis by EPA Method 8082. All solid wastes containing 50 parts per million (ppm) by weight (on a dry weight basis for other than liquid wastes) or greater of polychlorinated biphenyls (PCBs) are listed hazardous wastes, excluding small capacitors as defined in paragraph (3) of NYCRR Part 371 and PCB Articles drained in accordance with subparagraphs (2)(ii) and (iii) of Part 371 Section (e). PCB Articles that contain less than 50 ppm PCBs are not regulated as hazardous waste. 2.4 Inspection Report During the PCB Caulk sampling conducted on November 20, 2015, 12 samples were collected for analysis. The laboratory analysis performed on caulk/sealant samples revealed the following:

None of the sampled materials within the scope of work collected on the date of the inspection were found to be above the 50 ppm threshold for PCBs by laboratory analysis.

(SEE THE TABLE IN SECTION 2.5 FOR ANALYSIS RESULTS OF THE INDIVIDUAL PCB COMPOUNDS/PARAMETERS IN THE SAMPLES.

2.5 PCB Analysis Report Location - Exterior HAN 600 – Window Caulk – New Soft Gray

Sample # Parameter/ PCB

Compound

Analysis Method

Results (µg/kg) ppb

Results reported in ppm

Hazardous Waste (Y/N)

1120-BPC-600P-1 PCB-1016 EPA 8082 <397 <0.397

PCB-1221 EPA 8082 <397 <0.397

PCB-1232 EPA 8082 <397 <0.397

PCB-1242 EPA 8082 <397 <0.397

PCB-1248 EPA 8082 <397 <0.397

PCB-1254 EPA 8082 <397 <0.397

PCB-1260 EPA 8082 <397 <0.397

PCB 1262 EPA 8082 <397 <0.397

PCB-1268 EPA 8082 <397 <0.397

TOTAL N

Location - Exterior HAN 600 – Window Caulk – New Soft Gray


Compound

Analysis Method




1120-BPC-600P-2 PCB-1016 EPA 8082 <359 <0.359

PCB-1221 EPA 8082 <359 <0.359

PCB-1232 EPA 8082 <359 <0.359

PCB-1242 EPA 8082 <359 <0.359

PCB-1248 EPA 8082 <359 <0.359

PCB-1254 EPA 8082 <359 <0.359

PCB-1260 EPA 8082 <359 <0.359

PCB 1262 EPA 8082 <359 <0.359

PCB-1268 EPA 8082 <359 <0.359

TOTAL N

2.5 PCB Analysis Report (continued) Location - Exterior HAN 600 – Window Caulk – New Soft Gray


Compound

Analysis Method




1120-BPC-600P-3 PCB-1016 EPA 8082 <419 <0.419

PCB-1221 EPA 8082 <419 <0.419

PCB-1232 EPA 8082 <419 <0.419

PCB-1242 EPA 8082 <419 <0.419

PCB-1248 EPA 8082 <419 <0.419

PCB-1254 EPA 8082 <419 <0.419

PCB-1260 EPA 8082 <419 <0.419

PCB 1262 EPA 8082 <419 <0.419

PCB-1268 EPA 8082 <419 <0.419

TOTAL N

Location - Exterior HAN 601 – Window Caulk – Bottom Layer Soft Silver


Compound

Analysis Method




1120-BPC-601P-1 PCB-1016 EPA 8082 <467 <0.467

PCB-1221 EPA 8082 <467 <0.467

PCB-1232 EPA 8082 <467 <0.467

PCB-1242 EPA 8082 <467 <0.467

PCB-1248 EPA 8082 <467 <0.467

PCB-1254 EPA 8082 <467 <0.467

PCB-1260 EPA 8082 <467 <0.467

PCB 1262 EPA 8082 <467 <0.467

PCB-1268 EPA 8082 <467 <0.467

TOTAL N

2.5 PCB Analysis Report (continued) Location - Exterior HAN 601 – Window Caulk – Bottom Layer Soft Silver


Compound

Analysis Method




1120-BPC-601P-2 PCB-1016 EPA 8082 <464 <0.464

PCB-1221 EPA 8082 <464 <0.464

PCB-1232 EPA 8082 <464 <0.464

PCB-1242 EPA 8082 <464 <0.464

PCB-1248 EPA 8082 <464 <0.464

PCB-1254 EPA 8082 <464 <0.464

PCB-1260 EPA 8082 <464 <0.464

PCB 1262 EPA 8082 <464 <0.464

PCB-1268 EPA 8082 <464 <0.464

TOTAL N

Location - Exterior HAN 601 – Window Caulk – Bottom Layer Soft Silver


Compound

Analysis Method




1120-BPC-601P-3 PCB-1016 EPA 8082 <374 <0.374

PCB-1221 EPA 8082 <374 <0.374

PCB-1232 EPA 8082 <374 <0.374

PCB-1242 EPA 8082 <374 <0.374

PCB-1248 EPA 8082 <374 <0.374

PCB-1254 EPA 8082 <374 <0.374

PCB-1260 EPA 8082 <374 <0.374

PCB 1262 EPA 8082 <374 <0.374

PCB-1268 EPA 8082 <374 <0.374

TOTAL N

2.5 PCB Analysis Report (continued) Location - Exterior HAN 602 – Window Module Surround Caulk – Soft White


Compound

Analysis Method




1120-BPC-602P-1 PCB-1016 EPA 8082 <448 <0.448

PCB-1221 EPA 8082 <448 <0.448

PCB-1232 EPA 8082 <448 <0.448

PCB-1242 EPA 8082 <448 <0.448

PCB-1248 EPA 8082 <448 <0.448

PCB-1254 EPA 8082 <448 <0.448

PCB-1260 EPA 8082 <448 <0.448

PCB 1262 EPA 8082 <448 <0.448

PCB-1268 EPA 8082 <448 <0.448

TOTAL N

Location - Exterior HAN 602 – Window Module Surround Caulk – Soft White


Compound

Analysis Method




1120-BPC-602P-2 PCB-1016 EPA 8082 <452 <0.452

PCB-1221 EPA 8082 <452 <0.452

PCB-1232 EPA 8082 <452 <0.452

PCB-1242 EPA 8082 <452 <0.452

PCB-1248 EPA 8082 <452 <0.452

PCB-1254 EPA 8082 <452 <0.452

PCB-1260 EPA 8082 <452 <0.452

PCB 1262 EPA 8082 <452 <0.452

PCB-1268 EPA 8082 <452 <0.452

TOTAL N

2.5 PCB Analysis Report (continued) Location - Exterior HAN 602 – Window Module Surround Caulk – Soft White


Compound

Analysis Method




1120-BPC-602P-3 PCB-1016 EPA 8082 <391 <0.391

PCB-1221 EPA 8082 <391 <0.391

PCB-1232 EPA 8082 <391 <0.391

PCB-1242 EPA 8082 <391 <0.391

PCB-1248 EPA 8082 <391 <0.391

PCB-1254 EPA 8082 <391 <0.391

PCB-1260 EPA 8082 <391 <0.391

PCB 1262 EPA 8082 <391 <0.391

PCB-1268 EPA 8082 <391 <0.391

TOTAL N

Location - Exterior HAN 603 – Window Glazing – Black


Compound

Analysis Method




1120-BPC-603P-1 PCB-1016 EPA 8082 <417 <0.417

PCB-1221 EPA 8082 <417 <0.417

PCB-1232 EPA 8082 <417 <0.417

PCB-1242 EPA 8082 <417 <0.417

PCB-1248 EPA 8082 <417 <0.417

PCB-1254 EPA 8082 <417 <0.417

PCB-1260 EPA 8082 <417 <0.417

PCB 1262 EPA 8082 <417 <0.417

PCB-1268 EPA 8082 <417 <0.417

TOTAL N

2.5 PCB Analysis Report (continued) Location - Exterior HAN 603 – Window Glazing – Black


Compound

Analysis Method




1120-BPC-603P-2 PCB-1016 EPA 8082 <2010 <2.010

PCB-1221 EPA 8082 <2010 <2.010

PCB-1232 EPA 8082 <2010 <2.010

PCB-1242 EPA 8082 <2010 <2.010

PCB-1248 EPA 8082 <2010 <2.010

PCB-1254 EPA 8082 <2010 <2.010

PCB-1260 EPA 8082 <2010 <2.010

PCB 1262 EPA 8082 <2010 <2.010

PCB-1268 EPA 8082 <2010 <2.010

TOTAL N

Location - Exterior HAN 603 – Window Glazing – Black


Compound

Analysis Method




1120-BPC-603P-3 PCB-1016 EPA 8082 <404 <0.404

PCB-1221 EPA 8082 <404 <0.404

PCB-1232 EPA 8082 <404 <0.404

PCB-1242 EPA 8082 <404 <0.404

PCB-1248 EPA 8082 <404 <0.404

PCB-1254 EPA 8082 <404 <0.404

PCB-1260 EPA 8082 <404 <0.404

PCB 1262 EPA 8082 <404 <0.404

PCB-1268 EPA 8082 <404 <0.404

TOTAL N

Appendix A General conditions of inspection 1. MS Analytical neither accepts nor implies any liability for the implementation of the

recommendations found within this report. 2. MS Analytical cannot be held responsible or liable for the misrepresentation of fact,

misstatements or withholding of relevant information by those parties interviewed during this inspection.

3. This report is based on the condition and contents present at the site on the day of the

inspection. MS Analytical is not liable for materials, chemicals or other substances of concern that may have been removed from the site, cleaned or disposed of prior to the inspection date or subsequent to that date.

4. An inspection or risk assessment for asbestos and lead-based paint relies heavily upon

identification of homogeneous areas, with sampling and laboratory analysis then determined by the quantity of surfaces identified, generally accepted inspection protocols, regulatory requirements, and the inspector’s or risk assessor’s judgement. Specific sample locations are determined with the objective of selecting representative samples. As with any type of sampling, the possibility of obtaining a false positive or false negative does exist, is inherent in the sampling process, and can at times result from the fact that both lead and asbestos fibers are not always uniformly distributed throughout suspect surfaces or materials. Although MS Analytical attempts to minimize the risk of a false positive or false negative result through a comprehensive inspection protocol, the possibility does exist, and could only be completely eliminated through testing and analysis of 100% of each suspect surface, which of course is not practical.

Appendix B Certifications and licenses

Asbestos Consulting Services Environmental Assessments Lead Services

MICHAEL A MACIE

NYS ASBESTOS CERTIFICATIONS

PROJECT MONITOR

AIR MONITOR

INSPECTOR

Appendix C Laboratory report and chain of custody Laboratory Reports Chain of Custody Documents

Attn:

Address: 4169 Allendale ParkwayOrder #: 151447

Blasdell, NY 14219

Project: Buffalo Psychiatric Center

Stohl Environmental, LLC (4507)Customer:

MS215-602Number: PO Number:

Received 11/23/15

Matrix Bulk

Schneider Laboratories Global, Inc2512 W. Cary Street • Richmond, Virginia • 23220-5117804-353-6778 • 800-785-LABS (5227) • Fax 804-359-1475

Location: 400 Forest Ave. Buffalo, NY

11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location

UnitsRL* AnalystAnalysis DateResultMethod

151447-001 1120-BPC-600P-1 Exterior

Semi-volatile Organic Compounds

Aroclor - 1016 µg/Kg BRW11/25/15397<397SW846 8082A









PCB - Surrogate Recoveries

MIDCB

MITCMX

151447-002 1120-BPC-600P-2 Exterior












MIDCB

MITCMX

All internal QC parameters were met. Unusual sample conditions, if any, are described. Surrogate Spike results designated with "D" indicate that the analyte was diluted out. "MI" indicates matrix interference. Concentration and *Reporting Limit (RL) based on areas provided by client. Values are reported to three significant figures. PPM = mg/kg | PPB = µg/kg. The test results reported relate only to the samples submitted.

Page 1 of 7

Attn:


Blasdell, NY 14219




Received 11/23/15

Matrix Bulk



11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location


151447-003 1120-BPC-600P-3 Exterior












MIDCB

MITCMX

151447-004 1120-BPC-601P-1 Exterior












MIDCB

MITCMX


Page 2 of 7

Attn:


Blasdell, NY 14219




Received 11/23/15

Matrix Bulk



11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location


151447-005 1120-BPC-601P-2 Exterior












MIDCB

MITCMX

151447-006 1120-BPC-601P-3 Exterior












MIDCB

MITCMX


Page 3 of 7

Attn:


Blasdell, NY 14219




Received 11/23/15

Matrix Bulk



11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location


151447-007 1120-BPC-602P-1 Exterior












MIDCB

84%TCMX

151447-008 1120-BPC-602P-2 Exterior












MIDCB

43%TCMX


Page 4 of 7

Attn:


Blasdell, NY 14219




Received 11/23/15

Matrix Bulk



11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location


151447-009 1120-BPC-602P-3 Exterior












MIDCB

85%TCMX

151447-010 1120-BPC-603P-1 Exterior












MIDCB

45%TCMX


Page 5 of 7

Attn:


Blasdell, NY 14219




Received 11/23/15

Matrix Bulk



11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location


151447-011 1120-BPC-603P-2 Exterior












DDCB

DTCMX

151447-012 1120-BPC-603P-3 Exterior












MIDCB

51%TCMX


Page 6 of 7

Attn:


Blasdell, NY 14219




Received 11/23/15

Matrix Bulk



11/25/15Reported

Analysis Report

Cust. Sample ID

Parameter

Sample ID Location


151447-11/25/15 04:52 PM

QC Director

Reviewed By: Irma Faszewski

Parameter Method CT NY VA

Certifications

Matrix

X X XSW846 8082AAroclor - 1016 Bulk









Key

State Regulatory Agency - Lab ID Certificate Number

CT CT DPH PH-0118

NY NYELAP-11413 52362

VA Virginia DCLS/DEQ - 460135 8040

'X' indicates that the analyte is accredited.

If your state is not listed above, call laboratory for accreditation/certification information.


Page 7 of 7

Chain of Custody Document

Submitted to: (Lab Name)

Schneider

MS Job #

MS2015-602ENVIRONMENTAL CONSULTANTS

4169 ALLFNUALE POW, BUFFALO, Nzw YORK 1 ,4119

(716)312-8296 Va (716)3 12.8092yovw.msan4lyticatcom

Location of Sample

Exterior

ExteriorExteriorExteriorExteriorExteriorExteriorExteriorExterior

Exterior.ExteriorExterior

111111111NNINIIIIIMI11111111111111•11111=1111=1111111•1111•=111•1

Print Name

Michael Macie

Print Name Michael Made

Page 1 of 1

Date: 1 1 /20/2015

Date: 11/20/2015

Date:

Le< ?,�-Tz

Client: Hamilton Houston Lownie Arch. Contact

Location:

Manuel Rivera

Building: Buffalo Psychiatric Center 400 Forest Ave. Buffalo, NY

LEAD PCB'sX

Turnaround

RUSH r 24 Hour P` 72 Hour

r 5 Day

Wipes Soil: Bulk: EPA 8082

*ASTM wipes were used* r 48 Hour

Material Description

Window Caulk - New Soft Gray

Window Caulk - New Soft GrayWindow Caulk - New Soft GrayWindow Caulk - Bottom Layer Soft SilverWindow Caulk - Bottom Layer Soft SilverWindow Caulk - Bottom Layer Soft Silver

602 Window Module Surround Caulk - Soft WhiteWindow Module Surround Caulk - Soft WhiteWindow Module Surround Caulk - Soft White

603 Window Glazing - BlackWindow Glazing - BlackWindow Glazing - Black

Sample #

1120-BPC-600P-1

1120-BPC-600P-21120-BPC-600P-3 1120-BPC-601P-1 1120-BPC-601P-21120-BPC-601P-31120-BPC-602P-1 1120-BPC-602P-21120-BPC-602P-31120-BPC-603P-1 11 20-BPC-603P-21120-BPC-603P-3

HAN #600

601

Iliiii111111111111111111111 YIVVV:1151115 L447

Notes:

PCB Samples

PI If checked, also e-mail results to: [email protected]

Sampled . By:

Relinquished By:

Received By: