1

DigiNet CAPTURE BOARD

CONNECTION

2

INDEX

1. KMC-4400R…………………………………………………………………………………3

2. KMC-9016 (R5)…………………………….…………………………………………12

3. KMC-8016D ………………………………….……………………………………………15

4. KIO-8816A …………………………………….……………………………………………19

5. I-AMP ………………………………………………………………………..……………….… 23

3

1) SPECIFICATION

• 120 FRAME/SEWC OUTPUT

• HIGH SPEED PCI 2.1 INTERFACE

• MAX 16CH VIDEO INPUT

• WINDOWS 98 SDK

• NTSC/PAL VIDEO FORMAT

• YUV422 FORMAT DIGITAL VIDEO

1. KMC-4400R

4

2) FEATURE1~16CH VIDEO INPUT PORT

EXT. MONITOR OUTPUT (RCA)

1CH AUTOSELECT

1~4CH VIDEO INPUT PORT (BNC)

Reset JUMPER

Run , Power LED JUMPER

VIDEO BRIGHT CONTROL

5

1’ST CAM ----------- 16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

3) CONNECTION(4CH OVER)

6

3) CONNECTION(4CH OVER)

1’ST CAM ----------- 16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

1 – 4 CAM

5 – 8 CAM

9 – 12 CAM

13 – 16 CAM

GND

1’ST CAM VIDEO(1,5,9,13)

UPPER, LOWER SAME

2’ND CAM VIDEO(2,6,10,14)3’RD CAM VIDEO(3,7,11,15)

4’TH CAM VIDEO(4,8,12,16)

7

4) CONNECTION(8CH OVER)

Secondary CardPrimary Card

+

8

Primary Card Secondary Card

4) CONNECTION(8CH OVER)

8CH

1’ST CAM 8’ST CAM 5’ST CAM 4’ST CAM

CPU

PrimarySecondary

※ Primary card should be installed on the slot near CPU however, it is subject to charge in some mainboards

9

16CH

4) CONNECTION(8CH OVER)

Secondary Card

1’ST CAM 8’ST CAM 5’ST CAM 4’ST CAM

Secondary Card

9’ST CAM 16’ST CAM 13’ST CAM 12’ST CAM

Primary Card

Primary Card

10

RESET + - (NO SEQ)

RUN LED LEFT +

POWER LED LEFT PIN +

11

RESET + - (NO SEQ)

CONNECT TO THE MAIN BOARD’S RESET JUMPER

RUN LED LEFT +

POWER LED LEFT +

CONNECT TO THE MAIN BOARD’S HDD JUMPER

RUN LED RIGHT +

POWER LED RIGHT +

12

1) SPECIFICATION

• SAME AS OLDER KMC-9016

• OUTPUT 480 FRAME/SEC

• USE WITH KMC-4400R BOARD

• EXTERNAL MONITOR PORT

• COMPATIBLE DIGINET-3000 SYSTEM

2. KMC-9016(R5)

13

2) FEATUREA.FULL SCREEN BRIGHT ADJUST NOTICE. A : FIRST B : SECOND

NTSC/PAL NTSC : OPEN PAL : CLOSE

1~16CH VIDEO INPUT PORT

EXT. MONITOR OUTPUT (RCA)

DIVIDE SCREEN

B.DIVIDE SCREEN BRIGHT ADJUST

14

3) CONNECTION

16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

1’ST CAM

15

• UPGRADE KMC-7016D

• REPAIRED SCREEN VIBRATION

• 1CH TOTAL 30 FRAME/SEC

• 4 ~ 16CH TOTAL 25 FRAME/SEC

• NTSC/PAL VIDEO FORMAT

3. KMC-8016D

1) SPECIFICATION

16

1~4CH VIDEO INPUT(BNC)

1~16CH VIDEO INPUT

SCREEN BRIGHT ADJUST

Reset JUMPER

Run , Power LED JUMPER

AUDIO JUMPER

(USE LATER)EXT. MONITOR OUTPUT (RCA)

1CH AUTOSELECT

2) FEATURE

17

1’ST CAM ----------- 16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

3) CONNECTION

18

RESET JUMPER

RUN LED LEFT +

POWER LED LEFT + AUDIO (USE LATER)

19

• IO8816(ISA)’S UPGRADE

• PCI SLOT TYPE

• REMOTE CONTROL

• NOTICE) WHEN USE THIS CARD, MUST BE SET CMOS BIOS SETUP’S INTEGRATED PERIPHEARLS -> ONBOARD SERIAL PORT 1 : 3F8/IRQ4

4. KIO-8816A

KIO-8816A (PCI) IO-8816 (ISA)

1) SPECIFICATION

20

EXTERNAL MONITOR SENSOR INPUT,

CONTROL OUTPUTReset JUMPER

Run , Power LED

LED

REMOTE RX IR

P/T CONTROL RS422

COM PORT CONNECT PORT

2) FEATURE

EXT. MONITOR OUTPUT (RCA)

1CH AUTOSELECT

21

1’st CAM -- 16’th CAM

FRONT Video, REAR GND

THIS MARK IS Video

RESET JUMPER

RUN LED LEFT +

POWER LED LEFT +

FRONT LEFT 1-8 SENSOR INPUT 9,10 GND

REAR LEFT 1-8 CONTROL OUTPUT 9,10 GND

3) CONNECTION

22

CONNECT TO COM1 PORT AT DVR’S REAR

CONNECT

UPPER RS422 +

LOWER RS422 -

CONNECT

23

5. I-AMP

☞ This card use only DigiNet-3408, 3416 system

FRONT BACK

1) FEATURE

CONNECT TO PC POWER

24

2) CONNECTION

25