Upload
brianne-grant
View
223
Download
0
Embed Size (px)
Citation preview
DEPT OF LABOR
OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
OSHA STANDARDS
• ALWAYS CONSULT BEFORE LOOKING FOR OSHA CODES OR CONSENSUS STANDARDS!
• APPLIES TO MILITARY, CIVIL SERVICE, AND NON-APPROPRIATED FUND (MCCS) CIVILIANS
• DISCUSSES:– UNIT RESPONSIBILITIES
– COUNCILS & COMMITTEES
– TRAINING REQUIREMENTS
– INSPECTIONS
– GUIDELINES FOR INSPECTIONS BY FEDERAL OSHA
• HAS PROGRAM GUIDANCE FOR:• LOCKOUT/TAGOUT ENERGY CONTROL
• LITHIUM BATTERY SAFETY
• ASBESTOS SAFETY
• HAZARDOUS MATERIALS CONTROL
• FALL PROTECTION
• ERGONOMICS
• BLOODBORNE PATHOGENS
• OFFICE SAFTY
• Located within the Department of LaborLocated within the Department of Labor
• OSHA REGULATIONS– laws set forth by the Department of Labor
• Two general industry categories most Two general industry categories most applicable for Marine Corpsapplicable for Marine Corps – GENERAL INDUSTRY– CONSTRUCTION
PARAGRAPH NUMBERINGSYSTEM
29 CFR 1910.110(b)(13)(ii)(b)
liquefied petroleum code that discusses allowing temporary gas
lines in buildings
OSHA STANDARDSBREAKDOWN
Title - 29
Code of Federal Registration - CFR
Part - 1910
Section - .110
First Digit - Lower Case Alpha (b)
Second Digit - Arabic Number (13)
Third Digit -Lower Case Roman (ii)
Italicized-(b)
OSHA STANDARSPARAGRAPH NUMBERING
SYSTEM
Code of
Title Fed Reg Part Section
29 CFR 1910 .110
Within the Section it is broken down into paragraphs
SECTION BREAKDOWN
PART SECTION
1910 .110 (b)
Lower Case Alphabetical
First Tier of Paragraphs Beneath Section Level will be numbered in parentheses
SECTION BREAKDOWN29 CFR 1910.110(b)(13)(ii)(b)(7)(iii)
1910 .110 (b) (13)
Arabic Number
The Second Tier of Numbering involves Arabic numbers between subheadings.
SECTION BREAKDOWN
1910 .110 (b) (13) (ii)
Lower Case Roman
The Next Level uses the Lower Case Roman Numeral
SECTION BREAKDOWN
1910.110(b)(13)(ii) (b)
Italicized
Repeat the same paragraph numbering system, only italicize them.
OSHA CODE TERMINOLOGY
• Mandatory compliance– SHALL
– WILL
– MUST
• Recommended Compliance– SHOULD
• Optional Compliance– MAY
– CAN
29 CFR PART 1910GENERAL INDUSTRY
• Applies to Most Industrial and Office Environments
• Excluding Construction Activities
GENERAL INDUSTRY STANDARDS
• Portable Welding MachinesPortable Welding Machines– 29 CFR 1910.255
• Walking & Working SurfacesWalking & Working Surfaces– 29 CFR 1910.21 - .22
• Overhead Gantry CranesOverhead Gantry Cranes– 29 CFR 1910.179
• Fire ExtinguishersFire Extinguishers– 29 CFR 1910.157
• ForktrucksForktrucks– 29 CFR 1910.178
29 CFR 1926CONSTRUCTION
• Construction of buildings, roads, utilities
• Demolition of structures
• Excavation
CONSTRUCTION STANDARDS
• Excavation & TrenchingExcavation & Trenching– 29 CFR 1926.651-652
• Tools, Hand & PoweredTools, Hand & Powered– 29 CFR 1926.300 - .305 & .951
• Welding & CuttingWelding & Cutting– 29 CFR 1926.350-.354
• Chain SlingsChain Slings– 29 CFR 1926.251
• Earthmoving EquipmentEarthmoving Equipment– 29 CFR 1926.602
WILLIAM STEIGER ACTPUBLIC LAW 91-596
OSHA ACT 1970
GENERAL DUTY CLAUSE
EMPLOYER AGREES TO KEEP THE WORKPLACE FREE FROM RECOGNIZED HAZARDS
LET’S LOOK-UP SOME STANDARDS!