Upload
victor-fdez
View
225
Download
1
Embed Size (px)
Citation preview
8/3/2019 DeLorme Earthmate GPS PN20 Manual
1/93
Earthmate GPS PN-20GPS for wherever you go
DELORME
User Manual
Updated for 1.5 Firmware Release
OFF-ROAD ON-ROAD ON-WATER
8/3/2019 DeLorme Earthmate GPS PN20 Manual
2/93
Table o Contents
Getting Started ...........................................................................................................................................................................2
Basic Functions ..........................................................................................................................................................................9
Scenarios .................................................................................................................................................................................. 11
The Satellites Page...................................................................................................................................................................20The Map Page ..........................................................................................................................................................................23
The Compass Page ..................................................................................................................................................................37
The Trip Ino Page ....................................................................................................................................................................39
The Find Page ..........................................................................................................................................................................42
The Waypoints Page ................................................................................................................................................................50
The Routes Page ......................................................................................................................................................................55
The Tracks Page .......................................................................................................................................................................60
The Sun/Moon Page ................................................................................................................................................................64
The Tide Page ..........................................................................................................................................................................66
The Hunt/Fish Page .................................................................................................................................................................67
The Device Setup Page ............................................................................................................................................................68
Appendix A: Page Function Table ............................................................................................................................................74
Appendix B: Specifcations ......................................................................................................................................................78
Appendix C: Waypoint Symbols ..............................................................................................................................................82
Glossary ...................................................................................................................................................................................85
Index .........................................................................................................................................................................................88
8/3/2019 DeLorme Earthmate GPS PN20 Manual
3/93
2
Getting StartedThank you or purchasing the DeLorme Earthmate GPS PN-20. This versatile and compact GPS
receiver lets you create tracks o your travels, create routes so you never get lost, fnd points o
interest, and more!
This manual provides instructions or using all o the unctionality available on the Earthmate GPS
PN-20. Most o the chapters are based on pages, which are the main screens on the Earthmate
GPS PN-20. Each chapter describes the eatures o that particular page and the menu options thatare available rom that page. In addition, this manual also discusses basic unctions (such as map
panning, battery inormation, map data inormation, and more), as well as requently asked ques-
tions, warranty inormation, and so on.
Step 1 Installing the Batteries
The Earthmate GPS PN-20 is a battery-powered device. It can be powered by one rechargeable
Lithium-ion (Li- ion) battery or two AA batteries (NiCd, NiMH, alkaline, or lithium).
To install the batteries, unscrew the D-rings on the back o the Earthmate GPS PN-20 until you can
remove the battery cover. Then, insert the batteries according to the polarity symbols ound inside
the battery compartment. Position the battery cover on the Earthmate GPS PN-20 and re-screw the
D-rings into the Earthmate GPS PN-20.
Step 2 Turning On the Earthmate GPS PN-20
The Power button is located at the bottom-right corner o the button area. To turn on the Earthmate
GPS PN-20, press and hold the Power button or 1.5 seconds. The frst page that displays on the
screen ater you turn on the Earthmate GPS PN-20 is the Satellites Page. Your GPS status displays
in the upper-let corner o the Satellites Page. I you press the PAGE button, the Map Page displays
on the screen. The map will not center on your current location until you have achieved a 2-D or 3-D
fx. The deault view when a GPS fx cannot be obtained is your last GPS position.I it is taking a long time or the device to obtain a 2-D or 3-D fx, veriy it has a clear view o the sky.
Be sure that trees, buildings, and other obstacles are not blocking the Earthmate GPS PN-20. I the
device still cannot obtain a 2-D or 3-D fx, press the QUIT button to return to the Satellites Page,
press the MENU button, highlight the Set Current Location option, and then press ENTER. TheMap Page automatically displays. Pan the map to your current location and press ENTER.
Tips:
Settingthecorrectbattery
typewilloptimizethebat-
terysperformance.Formore
informationonselectingbat-
terytype,seeToModifythe
SystemSettingsonpage68.
BecausetheEarthmateGPS
PN-20hasareal-timeclock
thatrequirespowereven
whenthedeviceispowered
off,yourbatteriesarecon-
stantlyinuse.Ifyouuse
yourEarthmateGPSPN-20
sporadically(forexample,
morethanamonthbetween
uses),removethebatteries
forlong-termstorageand
thenreinsertthemwhenyouwanttousethedevice.
Tip:IftheEarthmateGPS
PN-20doesnotturnon,
ensurethatthebatteriesare
insertedintothedeviceprop-
erlyandthattheyaremostlyor
fullycharged.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
4/93
3
To turn o the Earthmate GPS PN-20, press the Power button and then press the ENTER button to
confrm you want to turn the Earthmate GPS PN-20 o.
Step 3 Using the Buttons on the Earthmate GPS PN-20
The buttons on the Earthmate GPS PN-20 give you access to all o the unctions on the device.
Each button has a unique purpose:
In/Out
Use the IN and OUT button to zoom in or zoom out on the map.
PresstheIN(left)sideofthebuttononcetozoomthemapinonelevelandshowmoredetail.
PressandholdtheINsideofthebuttontozoomthemapintoitsmaximumlevel.
PresstheOUT(right)sideofthebuttononcetozoomthemapoutonelevelandshowlessdetail.
PressandholdtheOUTsideofthebuttontozoomthemapouttoitsmaximumlevel.
PressINandOUTtoscrollbackandforwardthroughalist.
Page
Use the PAGE button to scroll through the enabled pages on the Earthmate GPS PN-20. The deaultpage button sequence is:
Satellites
Map
Compass
TripInfo
RouteDirections(availablewhennavigating)
For an overview o what you can view and do on each page, as well as each pages menu unctions,
see AppendixA on page 74.
Menu
The MENU button provides access to many unctions. Some menus are divided into top and bottom
sections that are separated by a line. The items in the top section are specifc to the active page.
The items in the bottom section are standard menu options that are available rom any page.
Tip:UsetheDeviceSetup/PageOrdersettingstoadd,
remove,orreorderthepages
thatdisplaywhenyoupress
thePAGEbutton.Formorein-
formation,seetheTo Modify
the Page Order Settings
sectiononpage71.
Getting Started
8/3/2019 DeLorme Earthmate GPS PN20 Manual
5/93
4
Find
The Find button is labeled with a magniying glass. Use it to search or a point o interest, waypoint,
address, coordinate, and more. You can search or a location based on its name or its proximity to
the current map center.
Mark Waypoint
The Mark button is labeled with a push pin. Use it to mark a waypoint at your current GPS location
or the cursor location (when panning). Once you mark a location, you can edit the waypoint name,coordinates, and elevation; provide comments about the waypoint; view the waypoint on the map;
navigate to the waypoint; average the waypoint or greater accuracy; save the waypoint; or delete
the waypoint.
Arrow Keypad
You can use the arrow keypad to:
Movethemapcursorleft,right,up,ordown.
Panthemapbymovingthecursorontheedgeofthemap.
Highlightoptionsinmenusorlists.Pressdowntomovetothenextentry,pressupfromthefrst entry to go to the last entry, or down rom the last entry to go to the frst entry. Press and
hold to quickly scroll through a menu or list.
Highlightcharactersonthekeyboardscreen.
Enter
You can use the ENTER button to:
Selectamenuentryoron-screenbutton/eld.
Getinformationaboutapointonthemap.PresstheENTERbuttonatanytimewhenviewing
the Map Page to see detailed inormation, i available.
Quit
The unction o the QUIT button varies depending on the current status o the Earthmate GPS PN-20.
You can use the QUIT button to cancel actions, such as panning, or keyboard entry, to delete
individual points when measuring distance, and so on. I you are perorming an action, pressing the
QUIT button moves you backward through the page sequence.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
6/93
5
Power
Use the Power button to turn the Earthmate GPS PN-20 on and o, to change the backlight set-
tings, or to reset the Earthmate GPS PN-20:
ToturntheEarthmateGPSPN-20on,pressandholdthePower button until the Welcomescreen displays.
ToturntheEarthmateGPSPN-20off,pressthePower button. When you see the PressENTER to power down message, press the ENTER button to confrm that you want to turn
o the Earthmate GPS PN-20. I you do not want to turn the Earthmate GPS PN-20 o, wait
fve seconds or press the QUIT button.
Tochangethebacklightintensitypercentage,pressandholdthePower button (or approxi-mately two seconds i the device is powered on) until you see the backlight screen display.
Press the arrow keypad to the let to move the slider and decrease the backlight intensity.
Press the arrow keypad to the right to move the slider and increase the backlight intensity.
Each level o intensity represents a 10% interval (100% is the maximum backlight intensity,
10% is the minimum backlight intensity).
Toturnthebacklightoff,pressandholdthePower button or three seconds (while the deviceis powered on) until the backlight shuts o.
Note: The backlight turns on any time you press a button unless you turned it o using theDevice Setup menu. For more inormation, see the ToModifytheDisplaySettingssection on
page 68.
WhenyouchargetheEarthmateGPSPN-20,thebacklightintensityisautomaticallyreduced
to decrease charging time.
ToresettheEarthmateGPSPN-20whenitison,pressandholdthePower button or sevenseconds.
Step 4 Transerring Map Data to the Earthmate GPS PN-20
Your Earthmate GPS PN-20 comes equipped with an overview-level base map showing world and
U.S. coverage. While this provides a great view o a large area, chances are that you will want a
detailed view o a smaller area or hiking, geocaching, and other activities. You can transer more
detailed maps to the Earthmate GPS PN-20 using:
Getting Started
Tip:Decreasethebacklighttimertohelpconservebattery
life.
PressENTERtoconrmthat
youwanttoturnthedeviceoff
8/3/2019 DeLorme Earthmate GPS PN20 Manual
7/93
6
Compatible DeLorme Mapping SotwareInstructions or sending maps to your EarthmateGPS PN-20 vary by application. For more inormation, see the mapping applications Help
system or instructions on sending maps to your Earthmate GPS PN-20.
Online Map Cutter or Earthmate GPS PN-20Visit http://data.delorme.com. You musthave an Internet connection to use this website. For instructions on sending maps to your
Earthmate GPS PN-20 with this online application, see the Online Map Cutter or Earthmate
GPS PN-20 Help system.
You can transer many types o data, such as satellite imagery, aerial imagery, USGS Topo Quad
maps, NOAA nautical charts, and more. Save maps in internal memory or on a removable memory
(SD/SDHC) card in the Maps directory.
Step 5 Use the Pages to Track, View Your Position While You Travel, and More
This manual describes all o the unctions ound in each page on the Earthmate GPS PN-20. See
the Table o Contents to fnd the headings that are most important to you.
About GPS
What is GPS?The Global Positioning System (GPS) applies modern technology to the ancient art o navigation.
The U.S. Department o Deense has developed and launched a series o positioning satellites in
an orbiting constellation. These satellites are used as reerence points much the same way stars
have been used in conventional navigation.
Using these satellites, a GPS receiver can determine your position anywhere on the globe. GPS
provides accurate inormation about coordinate position, elevation, speed, and direction o travel.
Many people have discovered the benefts o GPS or recording tracks and much more.
How Does GPS Work?
The GPS constellation consists o at least 24 satellites, each carrying several atomic clocks to
ensure the most accurate time possible. The satellites broadcast low-power radio waves containing
the satellites identity code and the exact time (to the nanosecond) that the message was sent.
When a GPS receiver picks up a satellite signal, it identifes the satellite and compares the signal
time with its own clock. The time dierence represents the time it has taken or that radio wave to
Note:Largemapsmaytake
longertotransfertothedevice.
Tip:Whileitisfastertoaccessmapsthathavebeensavedto
internalmemory,thequickestwaytotransfermapstoyour
deviceistocopythemaples
toanSDcardwithanSDcard
reader.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
8/93
7
travel rom the satellite to the receiver. Since radio waves travel at the speed o light, the time di-
erence can be used to calculate the distance rom the satellite to the GPS receiver.
The satellites identity code provides the location o the satellite, and the distance to the receiver
creates a sphere o possible locations or the GPS receiver. Without more inormation, the receiver
knows only that it is located somewhere on that sphere.
Two additional satellites are necessary to narrow down the receivers position. Each o these
satellites sends a similar radio message containing time and identity inormation. The GPS receiverchecks the orbital location o each satellite and uses the elapsed time to create two additional
spheres o possible locations. These three spheres intersect at two points; however, one o these
points is eliminated because it is ar away rom the Earths surace. Thereore, the second point
is assumed to be correct. The data rom these three satellites provides the receiver with a two-
dimensional location.
Data acquired rom a ourth satellite pinpoints the receivers exact location. This additional position-
ing inormation allows the GPS receiver to calculate its elevation, which is particularly important or
GPS users in mountainous locations.
GPS Position Accuracy
Any buildings, natural structures, or heavy oliage that obstruct the GPS antennas view o the sky
prevent satellite signals rom reaching the receiver and decrease the accuracy o your position.
Frequently Asked Questions
Can I install non-DeLorme maps on the Earthmate GPS PN-20?
DeLormes proessional GIS sotware, XMap, allows you to register non-DeLorme maps and
transer them to the Earthmate GPS PN-20.
How can I improve the lie o my batteries?When the backlight is on, it consumes a large part o the battery. Changing the backlight timer to
turn o ater 15 seconds could double the lie o your batteries. For inormation on changing the
backlight timer, see ToModifytheBacklightTimeron page 69.
Getting Started
Note:PlacingtheEarthmateGPSPN-20inabackpack
pocketorjacketshouldnot
resultinproblemswithGPSpositionaccuracy.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
9/93
8
Other ways to increase the lie o the batteries include:
Removingyourbatteriesforlong-termstorage
SettingtheGPSSettingstoPowerSavingmode
DisablingGPSwhileindoors
Usingbatterieswithhighermilliampratings(suchasDuracellUltras,EnergizerE2s,etc.)
Why are the new batteries that I put in the device the last time I used it (a month ago)
already dead?
Because the Earthmate GPS PN-20 has a real-time clock that requires power even when the device
is powered o, your batteries are constantly in use. I you use your Earthmate GPS PN-20 spo-
radically (more than a month between uses), remove the batteries or long-term storage and then
reinsert them when you want to use the device to improve battery lie.
Why does it take so long to fnd satellites?
Acquiring satellite data takes longer i the batteries are low or i the Earthmate GPS PN-20 does not
have a clear view o the sky. Be sure that trees, buildings, and other obstacles are not blocking the
Earthmate GPS PN-20 when you begin tracking.
Other actors, such as i you havent used the device or a long time or i youve moved the device a
great distance rom its last location, can aect the amount o time it takes to fnd satellites.
How do I reset the Earthmate GPS PN-20 when it will not turn o?
You can reset the Earthmate GPS PN-20 by holding the Power button or seven seconds. I that
does not work, remove and replace the batteries to reset the Earthmate GPS PN-20.
Why wont my Lithium-ion battery hold a charge?
The Li- ion battery is designed to last or 300 -500 uses, depending on environmental conditions.
Note:ThechargingcircuitinthePN-20wasdesignedfor
optimumoperationwiththe
RCR-V3Li-Ionbatterysold
throughDeLorme.OtherRCR-
V3Li-Ionbatteriesmaywork
andchargeinthePN-20,but
DeLormecanmakenoguaran-
teesofcompatibleoperation.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
10/93
9
Basic FunctionsThis chapter provides descriptions or some o the basic unctions o the Earthmate GPS PN-20.
Panning the Map
There are two ways to pan the map:
Manuallypanthemapbyplacingthecursoralongthemapedgeandholdthearrowkeypadin
the direction that you want to move the map. AutomaticallypanthemapwhenGPStracking/navigating.Themapautomaticallypansinthe
direction o travel when the GPS cursor travels outside o the map area.
Getting Inormation About a Map Object
There are two ways to get inormation about a map object.
Pressthearrowkeypadtopositionyourcursoroverthemapobjectsyouwanttolearnmore
about. The status bar at the bottom o the Map Page provides name inormation or the object.
Press ENTER to display the Ino Page.
PressEnteratanytimetogetinformationaboutobjectsthatareatyourcurrentGPSlocation.Note: I multiple objects are ound at the cursor location, the Multiple Objects screen dis-plays a list o the available objects at that location; objects you have created appear at the top
o the list. Use the arrow keypad to select an object and then press ENTER to view the Ino
Page or that object. To save a map object as a waypoint, highlight it and select Mark.
Navigating vs. Tracking
What is the dierence between navigating and tracking with the Earthmate GPS PN-20?
Youarenavigatingwith the Earthmate GPS PN-20 when you use it to ollow a route.
Youaretrackingwith the Earthmate GPS PN-20 when the GPS is on, but you are not ollowinga route.
Basic Functions
Note:Manuallypanningthemapwhensimulatingnaviga-
tionorplayingbackatrackwill
changethefocusofthemap
fromyourGPSlocationtothe
manuallypannedlocation.
Note:Onceyouhavemarkeda
mapobjectasawaypoint,you
caneditthewaypointdetails
(byhighlightingthewaypoint
information,pressingENTER
andthenmodifyingtheinfor-
mation),viewitbyhighlighting
ViewandpressingENTER,or
createaroutebyhighlighting
RouteandpressingENTER.
Moveyourcursortotheedge
ofthescreentopanthemapin
thatdirection
8/3/2019 DeLorme Earthmate GPS PN20 Manual
11/93
10
Using the Keyboard
The keyboard is accessible when you need to enter text, such as when editing a waypoint label.
Once the keyboard displays, use the arrow keypad to highlight the letter (AZ), number (09), symbol
(+, -, /, &), or punctuation (period, comma, apostrophe, exclamation point) you want to use. In addition,
the ollowing special unctions are provided:
Moves the cursor one space to the let without deleting characters.
Moves the cursor one space to the right without deleting characters.Changes the letters rom lowercase to uppercase letters (the active case is shown in the
keyboard). This unction toggles to all caps mode by pressing ENTER twice.
Moves the cursor one space to the let, deleting the character that was there.
Clears the content o the text feld being edited.
Accepts the changes made to the text feld and closes the keyboard.
Moves the cursor one space to the right, leaving a blank space.
Moves the cursor to the next line. This option can be used to type more than one line in a
comment feld.
Charging the Earthmate GPS PN-20
I you are using a DeLorme-supplied RCR-V3 Li- Ion battery, you can charge the Earthmate GPS
PN-20 battery by connecting the USB end o the cable to your computer and the other end o the
cable to the Earthmate GPS PN-20. To charge the device with the USB cable, the device must be
powered on while connected. You cannot use the Earthmate GPS PN-20 to charge rechargeable AA
batteries.
Storing Data on the Earthmate GPS PN-20
The Earthmate GPS PN-20 stores waypoints, tracks, routes, and the base map data in its internalmemory. You can save maps that are transerred to the Earthmate GPS PN-20 in internal memory
or on a removable memory (SD/SDHC) card located under the battery compartment.Tip:UsemultipleSDcardstocreateamaplibraryforlong
tripsortohavetheentirestate
inyourpocket.
Tips:
PressOUTtoquicklyhigh-
lighttheOKbutton.
PressINtodeleteonecharacteratatime.
PressQUITtocancelyour
keyboardentries.
Forexistingtext,enteralet-
tertoreplacethehighlighted
content.Tokeeptheexisting
textbutmovethecursor
tothebeginning/endofthe
text,selecttheoption
tomovethecursortothe
beginningortomovethe
cursortotheendofthetext.
Keyboardscreen
8/3/2019 DeLorme Earthmate GPS PN20 Manual
12/93
11
ScenariosYou can use your Earthmate GPS PN-20 or a variety o activities, including:
Geocaching
Birdwatching
Biking
ManagingGISdata
Andmuchmore!
Below are some scenarios or using the Earthmate GPS PN-20 in these situations.
Seeking a Geocache
Geocachingisapopularhide-and-seeksportforGPSusers.Hidersplaceacache(prizesand/orlog
book)atanapprovedlocationandseekersusethehidersclues(coordinateinformationandclues
thataresharedviatheInternetforsomegeocachelocations,visitwww.geocaching.com)tond
thecache.Thecacheusuallycontainsavarietyofprizesforthesuccessfulseeker(seekersare
encouragedtoobservethetakeone,leaveonepolicyonprizesinthecache).
Mike and his amily are looking or a un weekend activity that they can enjoy in the great outdoors.
A coworker tells Mike about geocaching and they decide to try the activity with their new Earth-
mate GPS PN-20.
Beore they leave or their adventure, they visit www.geocaching.com to fnd a cache in their area.
Once they fnd a cache, they use their compatible DeLorme mapping program to see the geocache
on the map and then download a map package o the area.
1. Visit www.geocaching.com and select the geocache you want to try to fnd.
2. Save the geocaches .loc fle to your computer.3. Open your DeLorme program and click the Draw tab.
4. Click File to open the draw fle editing area.
5. Click Import. The Import Draw File dialog box displays.
6. From the Files o type drop-down list, select LOC fle (*.loc).
Scenarios
8/3/2019 DeLorme Earthmate GPS PN20 Manual
13/93
12
7. Browse to the location where you saved the .loc fle in step 2, select the fle, and then click
Open. The draw objects in the imported fle display. A new waypoint layer is automaticallycreated or the imported fle.
8. Click Done to return to the Draw dialog area.
9. Click the HandheldExport tab in your sotware.
10. With the map centered on the geocache area, click the Select/Edit tool and then click thegrids on the map that cover the map area you want to export to the Earthmate GPS PN-20.
11. Name and save your map package.
12. Click the Exchange button on the Handheld Export tab or in the toolbar.
13. Send the geocache waypoint layer and map package to the device and then click Done.
Once the map and waypoint are loaded on the Earthmate GPS PN-20, they use the Waypoints Page
to locate the coordinate that was provided in the caches clue. Once the waypoint is ound, they
create a route rom their current position (home) to the waypoint location.
14. Press MENU and then select Waypoints.
15. Highlight the geocache waypoint in the list and then press ENTER.
16. Use the arrow keypad to highlight the Route button and then press ENTER.
17. Use the arrow keypad to highlight the Navigate button and then press ENTER.
18. Press PAGE until the Compass Page displays.
19. Use the Compass Page to fnd the direction o travel. The bearing arrow (large green arrow)
points in the direction o the next stop in the route. Use the bearing arrow to determine the
correct direction o travel towards the waypoint.
Once they arrive at the cache, they take a trinket rom the cache and leave a pencil they bought
while on a recent trip to Niagara Falls. Then they update the waypoint symbol on the Earthmate
GPS PN-20 to the geocache ound symbol. When they return rom their adventure, they visit the
caches page on www.geocaching.com and enter a log about their experience.
Hiding a Geocache
Mike and his amily had so much un on their frst geocache outing, that they decide to create a
geocache o their own!
Navigatetothegeocache
8/3/2019 DeLorme Earthmate GPS PN20 Manual
14/93
13
The amily decides to hide the cache along a public trail approximately 10 miles rom their home.
Beore they can add the cache to geocaching.com, they must get a very accurate coordinate or
the location where theyre hiding the cache. To do so, they must mark a waypoint at the geocache
location and then use the Averaging unction on the Earthmate GPS PN-20. When a waypoint is
averaged, a series o GPS readings or the waypoints location is recorded and averaged to increase
the positional accuracy o the waypoint.
1. Ensure you have a 3-D signal at the location o the geocache.
2. Press the Mark button. A waypoint is placed at the current GPS location.
3. Highlight the deault waypoint symbol and press ENTER. Use the arrow keypad to select the
geocache hidden symbol and press ENTER.
4. Highlight the deault label and press ENTER. Enter the new label Our First Geocache using
the keyboard, highlight OK, and press ENTER.
5. Highlight the Comment feld and press ENTER. Enter the comment inormation (Hid cacheunder pile o sticks) using the keyboard, highlight OK, and press ENTER.
6. Highlight the Avg button and press ENTER. The GPS status, coordinates, elevation, number
o readings at the location, and estimated accuracy display. The positional accuracy o theway-point is increased by the number o recordings. A small estimated accuracy number
indicates that the waypoint is very close to its actual coordinates.
7. Highlight the OK button and press ENTER.
8. Use the arrow keypad to highlight the Save button and then press ENTER.
Once the geocache location point is averaged, they visit www.geocaching.com and create a new
geocache with the averaged coordinate.
Bird Watching
TheEarthmateGPSPN-20isaperfectcompanionforbirdwatching.WithaerialimageryloadedontheEarthmateGPSPN-20,birdwatcherscanseeclearings,treecover,geologicalfeatures,andmore.In
addition,theycanusethewaypointfunctiontomarkwaypointsonthemapwhentheyseeparticular
typesofbirds.Theycanalsousethetrackfunctionalitytocreateabreadcrumbtrailwhiletheyretravel-
ingtotheirbirdwatchingspotandthenfollowthattrackbacktotheirvehiclesotheydonotgetlost.
Scenarios
MarkingtheOurFirstGeo-
cachewaypoint
8/3/2019 DeLorme Earthmate GPS PN20 Manual
15/93
14
Inthescenariobelow,Tom,abirdwatcher,usestheEarthmateGPSPN-20,aerialimagery,andthe
EarthmateGPSPN-20OnlineMapCentertoprepareforhisexpedition.
Beore Tom leaves or his trip, he uses the Earthmate GPS PN-20 Online Map Center to download
additional map data so he can get satellite and aerial views o the area where hell be. This is helpul
to Tom because he has heard that the bird population is greater near the swamp land. With the aerial
and satellite data available rom the Online Map Center, Tom can see the geological ormations in his
bird watching area beore he leaves, giving him a greater idea o where he should spend his day.
1. Visit http://data.delorme.com to download the area where you will be bird watching.
Once the map o the location is saved on the Earthmate GPS PN-20, Tom leaves or his bird watch-
ing trip. When he arrives at the location, he parks his truck, turns on the Earthmate GPS PN-20,
waits until he gets a 2-D or 3-D fx, places a waypoint to represent the parking lot, modifes his
tracking settings, and then turns on Track recording.
2. Press and hold the Power button to turn on the Earthmate GPS PN-20.
3. Press the Mark button on the device to place a waypoint at the parking lot location and pressENTER.
Note: To choose a dierent symbol, scroll to the top o the Waypoints screen to highlight thewaypoint symbol and press ENTER. Use the arrow keypad to fnd and highlight the symbol
you want.
4. Press MENU, highlight the Tracks option, and press ENTER.
5. Press MENU, highlight the Edit Track Settings option, and press ENTER.
6. Highlight the Record Points By drop-down list and press ENTER.
7. Highlight the Time option and press ENTER.
8. Highlight the Recording Interval text feld and press ENTER. Use the arrow keypad to
increase/decrease each digit. Press ENTER ater each digit is changed.9. I the On button is not activated, highlight the button and then press ENTER to activate it.
OR
I the On button is already activated, go to step 10.
Safety Tip:Besuretobring
amapandcompasswithyou
onyourexpeditionincasethe
batteriesinyourEarthmate
GPSPN-20arelow.
Tip:UsetheTimeoptionif
youwanttorecordalotofdetail.UsetheDistanceoption
ifyouaregoingtomakemany
stepsalongtheway.
Editingthetracksettings
8/3/2019 DeLorme Earthmate GPS PN20 Manual
16/93
15
Tom continues his journey to the bird-watching spot. While hes walking, he notices an eagle in a
tree and wants to use his Earthmate GPS PN-20 to mark a waypoint at the bird location.
10. While at the spot o the tree, press the Mark button.
11. Scroll to the top o the Waypoints screen to highlight the waypoint symbol and press ENTER.
Use the arrow keypad to fnd and highlight the bird icon and press ENTER.
12. Scroll to the label text feld (to the right o the bird icon) and press ENTER. Use the arrow
keypad to highlight the letter E and press ENTER. Repeat this step or each letter in the word
Eagle. When youre fnished, highlight OK and press ENTER.
13. Scroll to highlight the Save button and press ENTER.
When he arrives at the desired bird watching spot, he saves his track log, turns o the GPS device,
and spends the day bird watching.
14. Press MENU, select Tracks, and press ENTER.
15. Scroll to highlight the Save button and press ENTER.
16. Press the Power button to turn o the Earthmate GPS PN-20. Press ENTER when prompted.
When hes fnished or the day, he turns the GPS device back on, waits until he gets a 2-D or 3-D
fx, and then ollows his track to where he startedensuring he wont get lost. The process o ol-
lowing his initial track creates a new route that he can use to navigate back to the parking lot.
17. Press and hold the Power button to turn on the Earthmate GPS PN-20.
18. Press MENU, select Tracks, and press ENTER.
19. Select the track that was saved earlier that day and press ENTER.
20. Scroll to highlight the Follow button and press ENTER.
Tom ollows the route directions on the map screen and reaches his start location without getting lost.
Mountain BikingTheEarthmateGPSPN-20isalsoaperfectcompanionwhilemountainbiking.
Carla and Jordan are preparing or a ride at Slickrock Bike Trail. Beore they go, they download data
o the Moab, Utah, region with their compatible DeLorme sotware program. They create a route
that starts and fnishes at the trailhead and includes three stops: Shrimp Rock, Upper Shrimp Rock,
and Mt. View Cave. Then they export the data o the region, as well as the route they created, to
Scenarios
MarkingtheEaglewaypoint
8/3/2019 DeLorme Earthmate GPS PN20 Manual
17/93
16
their Earthmate GPS PN-20. Once they arrive at the trail, they mount their GPS devices onto their
bikes, power them on, and select the route they plan to use or navigation.
1. Press MENU, highlight the Routes option, and press ENTER.
2. Highlight the route and press ENTER. The map displays.
3. Highlight the Navigate button and press ENTER. The map displays.
4. Press MENU, highlight the Tracks option, and press ENTER.
5. Ensure the On button is activated. I it is not, highlight the On button and press ENTER toactivate it.
6. To view the location in real time, press QUIT to display the Map Page.
The GPS device not only tells them where they are in real time but also keeps a record (track) o
everywhere theyve been. Once theyve fnished the trail, they decide to save the track so that they
can see where theyve ridden.
7. Press MENU, highlight the Tracks option, and press ENTER.
8. Highlight the Save button and press ENTER.
Since they might want to visit this track again later, they decide to name the track with the trail nameand assign it the same color that they assign all o the trails theyve ridden. They also use the com-
ments eature in the Tracks screen to note i they thought the trail was easy, moderate, or difcult.
9. Highlight the Track text feld and press ENTER to name the track GW Forest using thekeyboard. Then, highlight OK and press ENTER.
10. Highlight the Color block and press ENTER. Use the arrow keypad to highlight the color blueand press ENTER.
11. Highlight the Comment text feld, press ENTER, and assign a difculty comment using thekeyboard. Then, highlight OK and press ENTER.
12. Highlight the View button and press ENTER to see a snapshot o where you went on the trail.
When they arrive home, they download the track and waypoint inormation into their DeLorme sot-
ware so they can see a larger view o where they were. They fnish by saving the track inormation
in their mountain biking library project.
Editingtrackdetails
Navigatingaroute
8/3/2019 DeLorme Earthmate GPS PN20 Manual
18/93
17
Mapping Assets in the Field
Up-to-datemapsareoftencriticaltoefcientlymanageandmaintaincompanyassets.Youmay
needseverallayersofinformationtolocateandupdateinformationabouttheseassetsintheeld,
suchasroad,topographic,andhistoricmaps,aswellashigh-resolutionaerialimageryandGISlay-
ers.TheEarthmateGPSPN-20isideallysuitedtohandletheseneeds;youcantransfervirtuallyany
typeofdatafromDeLormesoftwareontothedeviceforuseintheeld,andthenusetheEarthmate
GPSPN-20tomapnewassetsandtheconditionsofexistingassets.Youcanthenbringthisinfor-
mationbackintotheofcetoupdatethecentraldatabase.The division managers o a utility company are responsible or overseeing the bimonthly update o
the spatial database or each division. They must collect inormation regarding new line locations,
conditions, and areas requiring repair or replacement to update the database and assist in planning
or the next months maintenance schedule.
The company uses the Earthmate GPS PN-20 with DeLormes proessional XMap GIS sotware
to perorm the updates. Each division is divided into quadrants with crews o two assigned to each
quadrant. Each crew has an Earthmate GPS PN-20 and is responsible or uploading the maps and
data they need on the device beore heading out into the feld. This data includes an updated copy o
the quadrants GIS utility line layer, road and topographic maps, waypoints o pole mile markers, high-resolution aerial imagery downloaded rom the state GIS department, and digitally scanned paper
maps o utility line schematics. These maps are geo-registered to the DeLorme map using XMap.
Preparing data or and transerring data onto the Earthmate GPS PN-20
1. Open XMap, set up a subscription to the central database, and obtain an updated copy o the
utility layer or the division.
2. Load the GIS layer into the GIS tab and use the spatial query tool to isolate the line objects
within a particular quadrant.
3. From the ImageReg tab, open the digital image o the schematic map or the quadrant. Usethe GIS line layer as reerence to place points on the digital image that correspond to points
on the DeLorme map. Then, process the image to geo-register it to the map.
4. Visit the state GIS website and download any digital aerial imagery in .sid or .ti ormat that
corresponds to the quadrant. Use the Map Data tab to load the imagery into XMap.
Scenarios
8/3/2019 DeLorme Earthmate GPS PN20 Manual
19/93
18
5. From the Handheld Export tab, center the map on the quadrant and customize the handheld
grid size to best ft the area. Then, click the Select/Edit tool and select the grids on the mapthat cover the quadrant.
6. Click the Options button and select the check box next to each dataset to transer tothe Earthmate GPS PN-20. For high-resolution aerial imagery, select XMap Raster DataSnapshot. For topographic, road, and GIS data, select XMap USA Topographic Data. Forscanned historic maps, select the ImageReg Data series. Customize the display ranges o
the datasets based on your preerences.7. Name and save the map package. Then, click the Exchange button on the Handheld Export
tab or in the toolbar. Send the mile marker waypoint layer and saved map package containing
the road, topographic, historic, and aerial imagery maps to the device and then click Done.
Using the Earthmate GPS PN-20 in the feld
With all the data transerred to the Earthmate GPS PN-20, the feld crew or each quadrant is ready
to head into the feld to update and veriy the utility data. One feld crew is responsible or updating
a quadrant with signifcant additions and changes to the existing inrastructure. They have a list o
mile marker ranges where these changes took place.
1. Use the Routes option on the Earthmate GPS PN-20 to create a route rom the feld ofce
(current GPS location) to the utility waypoint mile marker next to the service road entrance.
2. Once the feld crew arrives at the entrance, the worker with the Earthmate GPS PN-20 di-
rects the driver to each mile marker on the list where utility additions and modifcations were
made. They use the bearing and distance inormation or each waypoint to navigate along
the service road. Once they are parallel to a mile marker, they set out on oot to the pipeline,
using the aerial imagery, topographic, and GIS data to give them feld reerence.
3. Once the line locations are located, the crew collects pertinent waypoints and tracks on the
Earthmate GPS PN-20 to record inormation about the line. They use the various waypointsymbols on the Earthmate GPS PN-20 to represent dierent eatures, such as areas in need
o service or areas where there are dangerous trees that need to be removed. When they
come across an area where the GIS data does not correlate with the location o the utility line
in the feld, they record a track or that length o segment and drop waypoints at each line vertex.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
20/93
19
4. When the feld crew is fnished, they return to the ofce and download the waypoints and
tracks to XMap. Then they review the data to update any labels that need clarifcation and put
additional notes or the points using the MapNote eature in the Draw tab.
5. Once they are fnished with the review, they synchronize their feld data to the central data-
base using the synchronize eature in XMap.
6. The next day, the database manager responsible or the division reviews their synchronized
data against the corporate GIS layer and updates the corporate layer within XMap.
Scenarios
8/3/2019 DeLorme Earthmate GPS PN20 Manual
21/93
20
The Satellites Page
Viewing the Satellites Page
Once you turn on the Earthmate GPS PN-20, the Satellites Page displays. The Satellites Page inorms
you o your current GPS status, the number o satellites the Earthmate GPS PN-20 is acquiring data
rom, the signal strength, and the GPS accuracy (available only when a 2-D or 3-D fx is obtained).
GPS and WAAS Status
GPS status displays in the upper-let corner o the page and displays the ollowing, depending on
your satellite acquisition status:
GPS OThe GPS is disabled.
No FixThe GPS cannot fnd sufcient satellite data to determine your current GPS position.
2-DThe GPS connection is successul, but the connection quality is not quite as sufcientas a 3-D fx. This usually indicates insufcient data or an accurate location because only three
satellites are being used or signals rom the satellites are poor. Move your receiver to another
location until you get better reception.
3-DThe GPS receiver is receiving sufcient satellite data to determine your location.
I WAAS displays in the upper-right corner o the page, the Earthmate GPS PN-20 has obtained a
WAAS connection. WAAS provides up to fve times greater position accuracy than a regular 2-D or
3-D connection. WAAS is available only in North America.
Satellite Constellation and Signal Graph
Both the satellite constellation and the satellite signal graph display visible satellites and their identi-
ying numbers, which are assigned by the Department o Deense.
In the satellite constellation, satellite-shaped icons display each satellites position in the sky relative
to the devices current position.
In the satellite signal graph, each satellite is represented as a bar that is sized according to signal
strength. Longer bars have greater strength and shorter bars have less strength.
The icons in the satellite constellation and the lines in the signal graph are color coded based on the
quality o the data they are transmitting:
SatellitesPage
Tip:Ifitistakingalongtime
forthedevicetoobtaina2-Dor3-Dx,verifyithasaclear
viewofthesky.Besurethat
trees,buildings,andother
obstaclesarenotblockingthe
EarthmateGPSPN-20.Ifthe
devicestillcannotobtaina
2-D/3-Dx,pressPAGEuntil
theSatellitesPagedisplays,
pressMENU,highlighttheSetCurrent Locationoption,andthenpressENTER.TheMap
Pagedisplaysautomatically.Panthemaptoyourcurrent
locationandpressENTER.
R d I di GPS i i ki h lli b i i i i d i Th S lli P
8/3/2019 DeLorme Earthmate GPS PN20 Manual
22/93
21
RedIndicates your GPS receiver is tracking the satellite, but it is not receiving data rom it.
GreenIndicates your GPS receiver is tracking the satellite, ephemeris data is available, andthe satellite is being used or navigation.
BlueIndicates your receiver is tracking the satellite, ephemeris data is available, the satelliteis being used or navigation, and the satellite has WAAS corrections available.
GPS Accuracy
The GPS accuracy displays in the lower-let corner o the screen in eet or meters, depending onthe measurement preerences you assigned in the Device Setup Page (see ToModifytheUnits
Settingson page 72 or more inormation). GPS accuracy is represented on the map by a circle with
a radius equal to the GPS accuracy, allowing you to see a representation o your accuracy in relation
to your map scale. The accuracy o the Earthmate GPS PN-20 is +/- 10 meters.
Battery Indicator
The battery indicator is a graphic representation o the current available battery power:
Four green barsIndicates a ull charge.
Three green barsOne quarter o the battery power has been used. Two yellow barsOne hal o the battery power has been used.
One red barThree quarters o the battery power has been used. Once the battery hasreached 5% o its total battery power, a low battery warning displays.
While the Li-Ion battery is charging, the battery indicator graphic is animated and the word Bat-
tery is replaced with Charging. Once the battery is ully charged, the battery indicator graphic
displays our static green bars and the word Charging is replaced with External until the charg-
ing cable is removed.
The Satellites Page
Batteryindicatorlabelchanges
toexternalwhencharging
Note:WAASwasdevelopedbytheFederalAviation
Administrationtoenhance
theaccuracyusuallyto
withinthreemetersofactual
positionofGPSreceivers
byprovidingamodiedGPS
signal.Aftercalculatingtheer-
rorfactoratgroundcontrolsta-
tionsthroughouttheU.S.,the
correctedsignalistransmitted
totwogeostationarysatellites
thatinturntransmittheGPS
signalbacktoEarth.
T Di bl GPS
8/3/2019 DeLorme Earthmate GPS PN20 Manual
23/93
22
To Disable GPS
There are many eatures on the Earthmate GPS PN-20 that do not require a GPS fx. You can turn
o the GPS connection using the Disable GPS option in the Satellites menu.
1. From the Satellites Page, press MENU.
2. Use the arrow keypad to highlight Disable GPS.
3. Press ENTER. GPS OFF displays in the upper-let corner o the screen and all satellites are
removed rom the constellation display.Notes:Youcanalsodisablethe
GPSusingtheDeviceSetup/
Systemmenuoption.Select
Disable GPSfromtheGPS
Settingsdrop-downlist.
WhenGPShasbeen
disabled,youcanenableit
bypressingMENUandthen
selectingEnable GPS.
GPSistemporarilydisabled
wheninsimulatemode(dur-
ingtrackplayback,navigationsimulation,andsoon).
IftheEarthmateGPSPN-20
isunabletoacquireaxafter
approximatelytenminutes,
youwillseethefollowing
message,Wouldyoulike
todisabletheGPSorcontin-
uesearchingforsatellites?
SelectDisabletodisableGPSorContinuetoallowtheEarthmateGPSPN-20to
keepsearchingforsatellites.
Note:Ifyoudonotchoosethecorrectbatterytypeinthe
DeviceSetupPage,thebattery
indicatormaynotprovideaccu-
rateinformation.SeeToModify
theSystemSettingsonpage
68formoreinformation.
Th M P The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
24/93
23
The Map Page
Viewing the Map Page
I a 2-D or 3-D fx is obtained, the Map Page displays the map data that is available or your current
GPS location. I a GPS fx cannot be obtained, the location o your last GPS fx displays on the map.
The color o the GPS arrow depends on your GPS signal.
AashingredarrowindicatesthattheEarthmateGPSPN-20cannotobtainaGPSsignal.
AbluearrowindicatesthatthedeviceisinTrackPlaybackmodeorSimulateNavigationmode. Ayellowarrowindicatesa2-Dx.
Agreenarrowindicatesa3-Dx.
Below the map are inormation felds. The inormation displayed in these felds varies based on the
selections you choose (or more inormation, see ToChangetheInformationFieldson page 25).
The scale is located above the inormation felds. A north arrow is also available in the upper-right
corner o the screen; this is available only when Heading Up is selected as the map orientation (or
Course Up is selected when navigating). Note: Raster maps rotate in 90 headings.
To View Map Data
The Earthmate GPS PN-20 comes standard with a base map showing high-level world and U.S.
coverage. You cannot remove the base map rom memory.
Several data types are compatible with the Earthmate GPS PN-20:
High-resolutionCities
ColorAerialImagery
AerialImagery(DOQQ)
USGSQuads(3DTQ)
NOAANauticalCharts
SatelliteImagery
DeLormeTopographicData
Worldbasedata
Tip:Youcanalsochoosetohidetheinformationeldsto
makethemaparealarger(for
moreinformation,seeToHide
theInformationFieldsonpage
24)orchangethenumberof
informationeldsthatdisplay
(formoreinformation,seeTo
ArrangetheInformationFields
onpage24).
MapPage
The Map Page
Th li b h h d l l i h d b T h h d
8/3/2019 DeLorme Earthmate GPS PN20 Manual
25/93
24
The list above shows the deault layering o the data types rom top to bottom. To change the data
layering, see LayeringYourDataon page 31.
To Show/Hide the Inormation Fields
You can hide the inormation felds to enlarge the map area.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Ino Fields.
3. Press ENTER. The Ino Fields Setup screen displays.4. Use the arrow keypad to highlight Hide Ino Fields. Press ENTER. The inormation felds are
hidden.
Note: I Show Ino Fields displays, the inormation felds are hidden. Press ENTER to displaythe inormation felds.
To Arrange the Inormation Fields
You can change the inormation felds to display as one wide feld, one wide feld and two narrow
felds, our narrow felds, two wide felds, or two narrow felds.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Ino Fields.
3. Press ENTER. The Ino Fields Setup screen displays.
4. Use the arrow keypad to highlight Arrange Ino Fields.
Note: I Show Ino Fields displays, the inormation felds are hidden. Press ENTER to displaythe inormation felds and repeat steps 2 and 3.
5. Press ENTER
6. Use the arrow keypad to select the inormation feld style you want to view.7. Press ENTER.
ArrangeInfoFieldsmenuoption
T Ch th I ti Fi ld The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
26/93
25
ChangeInfoFieldsmenuoption
To Change the Inormation Fields
You can customize the inormation felds to display the inormation that is most important to you.
You may want to change the inormation that displays based on the type o activity you are doing.
Note: The inormation felds change when navigating.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Ino Fields.
3. Press ENTER. The Ino Fields Setup screen displays.4. Use the arrow keypad to highlight Change Ino Fields.
Note: I Show Ino Fields displays, the inormation felds are hidden. Press ENTER to displaythe inormation felds and repeat steps 2 and 3.
5. Press ENTER.
6. Use the arrow keypad to highlight the inormation feld you want to change.
7. Press ENTER. The available inormation feld options display.
8. Use the arrow keypad to select the inormation feld.
9. Press ENTER.
10. Press QUIT to exit Change Ino mode.
The available inormation felds include:
Inormation Field Option Description
Back on Course The direction o travel needed to return to the route while
continuing in the direction o the destination. Expressed in
degrees.
Battery Lie The percentage o battery power that remains or the Earth -mate GPS PN-20.
The Map Page
Notes:
Theinformationeldsyouselectmaybeabbreviated
onthescreen.Forexample,
VelocityMadeGooddisplays
asVMG.
Wheninformationisnot
available(forexample,the
DistancetoFinishinforma-
tioneldisonlypertinent
whennavigating),dashes
(--)displayintheapplicable
eld.
Note:Theprimarycoordi-
natesareshownwhenever
coordinatesaredisplayed(for
example,whenpanning).
Inormation Field Option Description
8/3/2019 DeLorme Earthmate GPS PN20 Manual
27/93
26
Inormation Field Option Description
Bearing The direction o travel rom the current location to the desti-
nation (fnish or next stop). Expressed in degrees. Displays
a green arrow pointing in the direction o the next waypoint
or route point. The arrow is grayed out when no movement
is reported by the device. It is green when the device is
moving.
Coordinates: Primary The coordinates or the current GPS location, cursor position,or map center in the primary ormat. The deault is Lat/
Lon. You can change the ormat in Device Setup>
Units>Coordinates: Primary.
Coordinates: Secondary The coordinates or the current GPS location, cursor position,
or map center in the secondary ormat. The deault is
UTM/UPS. You can change the ormat in Device Setup>
Units>Coordinates: Secondary.
Course The direction o travel on a route rom the starting location to
the destination (fnish or next stop). Expressed in degrees.
Device Odometer The total distance traveled in all trips.
Distance to Finish The distance rom the current location to the route fnish.
Distance to Next Stop The distance rom the current location to the next stop in the route.
Distance to Next Turn The distance rom the current location to the next turn in the route.
Elevation The altitude (height) above or below sea level. Expressed in
distance.
Elevation: Maximum The maximum elevation achieved. Expressed in distance.
This feld may be reset when you clear Trip Ino.
Elevation: Minimum The minimum elevation achieved. Expressed in distance.
This feld may be reset when you clear Trip Ino.
Inormation Field Option Description The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
28/93
27
Inormation Field Option Description
ETA at Finish The Estimated Time o Arrival at the route fnish. Expressed
as hours:minutes AM/PM. ETA is based on the current
device time, not on the local time at the destination.
ETA at Next Turn The Estimated Time o Arrival at the next turn in the route.
Expressed as hours:minutes AM/PM. ETA is based on the
current device time, not on the local time at the turn.
ETA at Next Stop The Estimated Time o Arrival at the next stop in the routeExpressed as hours:minutes AM/PM. ETA is based on the
current device time, not on the local time at the next stop.
Finish The Finish label as it appears in the route directions.
GPS Accuracy The calculated accuracy o the GPS. Expressed in distance.
GPS Status The current status o your GPS device. No Fix, 2-D, or 3-D.
Heading The current direction o travel. Expressed in degrees.
Moonrise/Moonset The time o day at which the moon will rise and set.
Expressed as hours:minutes AM/PM. This inormation iscalculated or the specifc geographic area where the GPS
has acquired a 3-D fx.
Next Stop The label or the next stop as it appears in the route directions.
Next Turn The label or the next turn as it appears in the route directions.
Also displays an arrow showing the direction o the turn/
route direction inormation.
Next Turn Arrow The arrow representing the next turn as it appears in the
route directions. No label text displays.
O Course The perpendicular distance between the current location
and the route. Expressed in distance.
Speed The current rate o travel or the device. Expressed in
distance per unit o time.
The Map Page
Inormation Field Option Description
8/3/2019 DeLorme Earthmate GPS PN20 Manual
29/93
28
Inormation Field Option Description
Speed: Average The average speed o the device including stop time.
Expressed in distance per unit o time. This feld may be
reset when you clear Trip Ino.
Speed: Maximum The maximum speed achieved. Expressed in distance per
unit o time. This feld may be reset when you clear Trip
Ino.
Speed: Moving Average The average speed o the device excluding stop time.Expressed in distance per unit o time. This feld may be
reset when you clear Trip Ino.
Sunrise/Sunset The time o day at which the sun will rise and set. This
inormation is calculated or the specifc geographic area
where the GPS has acquired a 3-D fx. Expressed as
hours:minutes AM/PM.
Time/Date The time o day and date based on the current GPS location;
accounts or Daylight Saving Time and time zone adjustments.
Time is expressed as hours:minutes AM/PM and date is
expressed as day-month-year (or example, 01-JAN-08).
Time to Finish The calculated time to the route fnish based on road
classifcations and deault speed settings.
Time to Moonrise/set The time remaining until the moon rises and sets. This
inormation is calculated or the specifc geographic area
where the GPS has acquired a 3-D fx.
Time to Next Stop The calculated time to the next stop in the route based on
road classifcations and deault speed settings.Time to Next Turn The calculated time to the next turn in the route based on
road classifcations and deault speed settings.
Inormation Field Option Description The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
30/93
29
Time to Sunrise/set The time remaining until the sun rises and sets. This inormation
is calculated or the specifc geographic area where the
GPS has acquired a 3-D fx.
Trip: Odometer The total distance the GPS device has been moving. This
inormation may be reset when you clear Trip Ino.
Trip: Time Moving The total time the GPS device has been moving. This
inormation may be reset when you clear Trip Ino.Trip: Time Stopped The total time the GPS has been tracking but not moving.
This inormation may be reset when you clear Trip Ino.
Trip: Time Total The total time the GPS has been tracking, both moving and
stopped. This inormation may be reset when you clear Trip Ino.
Velocity Made Good The component o the current speed that is in the direction
o the route destination. Expressed in distance per unit o time.
Vertical Speed The current rate o vertical travel or the device. Expressed
in distance per unit o time.To Reset the Inormation Fields
The Map menu oers a Restore Ino Deaults option that allows you to change the custom settings
you made to the Show Ino Fields, Arrange Ino Fields, and Change Ino Fields drop-down lists back
to their deault settings.
Option Deault Setting
Show Ino Fields Selected
Arrange Ino Fields 2 narrow felds (when tracking)
4 narrow felds (when navigating)
Change Ino Fields Speed, Heading (when tracking)
Next Turn, Dist to Finish, Time to Turn, Dist to Turn
(when navigating)
p g
Use the steps below to reset the inormation felds to their deault settings.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
31/93
30
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Ino Fields.
3. Press ENTER. The Ino Fields Setup screen displays.
4. Use the arrow keypad to highlight Restore Ino Deaults.
Note: I Show Ino Fields displays, the inormation felds are hidden. Press ENTER to display
the inormation felds and repeat steps 2 and 3.5. Use the arrow keypad to highlight.
6. Press ENTER. The inormation felds return to their deault settings.
Turn Imagery On/O
You can turn on imagery to display it on the map or turn it o i you do not want to display it on the map.
1. From the Map Page, press MENU.
2. I Turn Imagery On is highlighted, imagery is turned o. Press ENTER to turn on imagery.
OR
I Turn Imagery O is highlighted, imagery is turned on. Press ENTER to turn o imagery.
To Measure Distance and Area
Your Earthmate GPS PN-20 has a measurement tool that allows you to measure the distance o a
line or perimeter and area o a polygon.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Measure Distance and press ENTER.
3. Use the arrow keypad to move the cursor to the area on the map where you want to place
the frst point o the line/polygon.4. Press ENTER to place the frst point o the line/polygon on the map.
5. Repeat steps 3 and 4 or each point in the line/polygon you want to measure. The Pan Loca-
tion Inormation that displays in the upper-right corner o the screen changes to display the
heading rom the last measurement node to your current GPS location, the leg distance, as
Tip:PressQUITtodeletethelastmeasurementpoint.To
deletetheentiremeasure-
mentobject,pressQUITuntil
allmeasurementpointsare
deletedfromthemap.
Measuringdistanceonthemap
well as the total distance rom the last measurement node to the frst measurement node. It The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
32/93
31
displays the area once you close a polygon.
Note: Lines must contain at least two points. To make a polygon, you must close the shapeby placing the last point on top o the frst point. Hovering the cursor over the start location
snaps to the point and closes the object when you press ENTER to commit the point.
To Set Up the Map
Use the Map Setup option to customize the map by defning data type layering, showing/hiding map
packages, and choosing map orientation, POI detail, how waypoints display on the map, and scale.
Layering Your Data
You can use the Data Layering menu option to prioritize the order in which to display the many
dierent data types available or use on the Earthmate GPS PN-20. Data layers at the top o the list
display frst when available. For example, i you have DeLorme Topographic Data and Aerial Imag-
ery (DOQQ) coverage or the same area, the data type with the highest priority displays on the map
based on the deault Data Layering settings. The deault order is as ollows:
1. Draw Layers
2. Custom Raster (XMap only)3. ImageReg (XMap only)
4. High-resolution Cities
5. Color Aerial Imagery
6. Aerial Imagery (DOQQ)
7. USGS Quads (3DTQ)
8. NOAA Nautical Charts
9. Satellite Imagery
10. Custom Vector (XMap only)
11. DeLorme Topographic Data
12 Base Map DataLayeringmenuoptions
MapSetupmenuoptions
Modiy the deault layering order with the Data Layering option in the Map Setup screen.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
33/93
32
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the Data Layering button.
5. Press ENTER. The Data Layering screen displays a list o all o the data types loaded on the
Earthmate GPS PN-20. The data type at the top o the list has the highest priority. The data
type at the bottom o the list has the lowest priority.
6. Use the arrow keypad to highlight the data type that you want to move up or down in the list.
7. Once the data type you want to move is highlighted, press the arrow keypad and highlight
the up or down arrow key to the right o the data types.
8. Press ENTER to move the data type. I you want to move the data type more than one level
away rom its current state, press ENTER as many times as it takes to move the data type so
it is in the order you want it.
9. Press the arrow keypad to the let to return to the layering list.
10. Repeat steps 6-9 or each data type you want to reorder in the list.
Showing/Hiding Maps Exported From a Compatible DeLorme Mapping Program
Ater you import a map rom a compatible DeLorme mapping program, you can view or hide it on
the Earthmate GPS PN-20 using the Data Management option. You may want to hide a map to see
what is underneath it; or example, raster maps are displayed above vector maps. To change the
priority o how maps are displayed, see LayeringYourDataon page 31.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup and press ENTER.
3. Highlight Data Management and press ENTER. The Data Management screen displays themaps that have been downloaded to the Earthmate GPS PN-20. A map is shown i its check
box is selected and is hidden i its check box is cleared.
4. Use the arrow keypad to highlight the map you want to hide or show. Inormation about the
map, including the types o data, displays in the bottom section o the screen. I you want to
DataManagementmenu
options
view more inormation about the map, press MENU, use the arrow keypad to highlight DataD t il d ENTER Th l l l i ti d t d t t
The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
34/93
33
Detail, and press ENTER. The name, zoom level, scale inormation, save date, data types,and version inormation display. Press QUIT to return to the Data Management screen.
5. I the check box next to the map is selected and you want to hide the map rom view, press
ENTER to clear the check box and hide the map.
OR
I the check box next to the map is cleared and you want to show the map on the screen,
press ENTER to show the map.6. Optional: To view the maps center on the screen, press MENU, use the arrow keypad to
highlight View Map, and press ENTER.
Changing the Map Orientation
You can change the map orientation based on your preerence as you move, but note that raster
maps rotate in 90 headings. Choose to make the map display:
North UpNorth is always represented at the top o the map screen.
Heading UpThe direction in which you are traveling is always represented at the top o the
map screen. Displays the North Arrow in the upper-right corner o the map screen. Course UpThe direction o the fnish o your route is always represented at the top o the map
screen. Displays the North Arrow in the upper-right corner o the map screen when navigating.
You can modiy the map orientation using the Orientation drop-down list in the Map Setup screen.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the Orientation drop-down list and press ENTER.
5. Use the arrow keypad to highlight North Up, Heading Up, or Course Up and press ENTER.
Orientationmenuoption
Note:Ifyouwanttoperma-nentlyremovethemapfrom
theEarthmateGPSPN-20,
pressMENU,usethearrow
keypadtohighlightDataDetail,andpressENTER.Then,usethearrowkeypadto
highlighttheDeletebutton,andpressENTER.
Note:YoucannotusetheFind
Pagetosearchhiddenmaps.
Changing the Map StyleYou can change the map style using the Map Style drop down list in the Map Setup screen Topo
8/3/2019 DeLorme Earthmate GPS PN20 Manual
35/93
34
You can change the map style using the Map Style drop-down list in the Map Setup screen. Topo
View displays all topographic data as it was saved in the map package; this is the deault view.
Street View hides the contours and land cover or a clean road map and aster map panning.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the Map Style drop-down list and press ENTER.5. Use the arrow keypad to highlight Street View or Topo View and press ENTER.
Showing Hybrid MapsYou can show points, lines, and labels on top o imagery. I you select this option, it changes the
draw order or the data layers but does not change the order listed on the Data Layering page. The
view is changed only rom zoom level 13 through zoom level 19.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.4. To show hybrid maps, under Map Style, highlight Show Hybrid Maps and press ENTER to
select the check box. I you do not want to show hybrid maps, clear the check box.
Changing the Level o POI DetailSeveral compatible data types contain points o interest (such as trails, mountains, accommodations,
restaurants, and more) that display as symbols on the map. With the POI Detail option in the Map
Setup screen, you can choose to hide all POIs, show only major POIs, or show all POIs. Changing this
level o map detail is helpul when there are multiple point o interest symbols cluttering the map.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the POI Detail drop-down list and press ENTER.
5. Use the arrow keypad to highlight Hide POIs, Show Major POIs, or Show All POIs andpress ENTER.
POIDetailmenuoption
Hybridmap
Showing/Hiding Waypoint Symbols
Th Hid W i t S b l ti l t h hid i t b l th
The Map Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
36/93
35
The Hide Waypoint Symbols option lets you show or hide waypoint symbols on the map.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the Hide Waypoint Symbols drop-down list and pressENTER.
5. Select the option you want to use and press ENTER.
Using Small Waypoint Symbols
The Small Waypoint Symbols option lets you reduce the waypoint symbol size above a specifc
scale to reduce map clutter.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the Small Waypoint Symbols drop-down list.5. Press ENTER.
6. Use the arrow keypad to highlight a symbol option or Never (to never use small waypointsymbols) and press ENTER.
Setting the Scale
The scale option lets you set the type o scale you want to use on your maps.
1. From the Map Page, press MENU.
2. Use the arrow keypad to highlight Map Setup.
3. Press ENTER. The Map Setup screen displays.
4. Use the arrow keypad to highlight the Scale drop-down list.
5. Press ENTER.
6. Use the arrow keypad to highlight Bar, Zoom, or Ratio and press ENTER.Scalemenuoptions
SmallWaypointSymbolsmenu
option
Deault Settings in the Map Setup Screen
The Map Setup screen deault settings are as ollows:
8/3/2019 DeLorme Earthmate GPS PN20 Manual
37/93
36
The Map Setup screen deault settings are as ollows:
Option Deault Setting
Data Layering GIS Layers (XMap only)
Draw Layers
Custom Raster (XMap only)
ImageReg (XMap only)
High-Resolution Cities
Color Aerial Imagery
Aerial Imagery (DOQQ)
USGS Quads (3DTQ)
NOAA Nautical Charts
Satellite Imagery
Custom Vector (XMap only)
DeLorme Topographic Data
Orientation Heading Up
POI Detail Show All POIs
Waypoint Detail Show Waypoints
Small Waypoint Symbols Never
Scale Bar
The Compass Page The Compass Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
38/93
37
Viewing the Compass Page
TheCompassPageisagraphicrepresentationofatraditionaloatingneedlecompass.Itsappear -
ance diers i you are navigating a route or tracking.
The compass rotates so that the heading is always up. You can choose to direct the bearing arrow
when you are navigating so that it points in the direction o the next stop on the route or it points
you back on course i you leave the route.To Direct the Route Arrow
Follow these steps to change the route arrow direction.
1. From the Compass Page, press MENU.
2. Use the arrow keypad to highlight Direct Route Arrow.
3. Press ENTER.
4. Use the arrow keypad to select the Direct to Next Waypoint or Back on Course.
5. Press ENTER.
To Arrange the Inormation Fields
You can change the inormation felds to display as one wide and two narrow felds, our narrow
felds, or two wide felds.
1. From the Compass Page, press MENU.
2. Use the arrow keypad to highlight Arrange Ino Fields.
3. Press ENTER.
4. Use the arrow keypad to select the inormation feld style you want to view.
5. Press ENTER.
To Change the Inormation Fields
You can customize the inormation felds to display the inormation that is most important to you.
You may want to change the inormation that displays based on the type o activity you are doing.
Note: The inormation felds change when navigating.
CompassPage
1. From the Compass Page, press MENU.
2 Use the arrow keypad to highlight Change Ino Fields
8/3/2019 DeLorme Earthmate GPS PN20 Manual
39/93
38
2. Use the arrow keypad to highlight Change Ino Fields.
3. Press ENTER.
4. Use the arrow keypad to highlight the inormation feld you want to change.
5. Press ENTER. The available inormation feld options display.
6. Use the arrow keypad to select the inormation feld.
7. Press ENTER.
8. Press QUIT to exit Change Ino mode.
To Restore the Inormation Fields to their Deault Settings
Use the steps below to reset the inormation felds to their deault settings.
1. From the Compass Page, press MENU.
2. Use the arrow keypad to highlight Restore Ino Deaults.
3. Press ENTER.
Note:TheEarthmateGPS
PN-20doesnothaveamagnet-
iccompassandcandetermine
headingonlywhilemoving.
The Trip Ino Page The Trip Ino Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
40/93
39
Viewing the Trip Ino Page
The Trip Ino Page includes eight inormation felds that occupy the entire screen (three inormation
felds display i the Earthmate GPS PN-20 is in large text mode). You can customize each feld with
one o the many available inormation feld options (see page 25 or a table o the inormation feld
options).
To Change the Inormation FieldsYou can customize the inormation felds to display the inormation that you want to see. You may
want to change the inormation that displays based on the type o activity you are doing.
Note: The inormation felds change when navigating.
1. From the Trip Ino Page, press MENU.
2. Use the arrow keypad to highlight Change Ino Fields.
3. Press ENTER.
4. Use the arrow keypad to highlight the inormation feld you want to change.
5. Press ENTER. The available inormation feld options display.6. Use the arrow keypad to select the inormation feld or move to another feld.
7. Press ENTER.
8. Press QUIT to exit Change Ino mode.
To Show Large Text
Use the Show Large Text option to view large inormation felds. The inormation felds vary depend-
ing on i you are tracking or navigating.
1. From the Trip Ino Page, press MENU.
2. Use the arrow keypad to highlight Show Large Text.
Note: The Show Large Text option is a toggle option that changes to Show Small Textwhen the large text option is activated.
3. Press ENTER.
TripInfoPage
4. To change which inormation felds display in large text:
a) Press MENU, highlight the Change Ino Fields option, and press ENTER.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
41/93
40
a) Press MENU, highlight the Change Ino Fields option, and press ENTER.
b) Use the arrow keypad to highlight the inormation feld to change.
c) Press ENTER. The available inormation felds display.
d) Use the arrow keypad to select the inormation feld to add.
e) Press ENTER.
) Repeat steps be or each inormation feld you want to change.
To Reset the Trip Inormation
Use the Reset Ino option in the Trip Ino menu to start a new trip and reset the odometer, speed
inormation, or elevation inormation.
1. From the Trip Ino Page, press MENU.
2. Use the arrow keypad to highlight Reset Ino.
3. Press ENTER.
4. To reset the trip odometer, time moving, time stopped, and time total, use the arrow keypad
to highlight Reset Trip Values. Press ENTER to select the check box. Press ENTER again toclear it.
OR
To reset the average speed, maximum speed, and moving average values, use the arrow
keypad to highlight Reset Speeds. Press ENTER to select the check box. Press ENTER againto clear it.
OR
To reset the minimum and maximum elevation inormation, use the arrow keypad to highlight
Reset Elevations. Press ENTER to select the check box. Press ENTER again to clear it.
OR
To reset the device odometer, use the arrow keypad to highlight Reset Device Odometer.Press ENTER to select the check box. Press ENTER again to clear it.
ShowLargeTextmenuoption
ResetTripValuesmenuoption
Note: Resetting Trip Values resets the trip odometer or the current Trip Ino reading, whileresetting Device Odometer resets the cumulative odometer or all trips on the device.
The Trip Ino Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
42/93
41
5. Highlight Reset Now and press ENTER.
To Restore the Inormation Fields to their Deault Settings
Use the steps below to reset the inormation felds to their deault settings.
1. From the Trip Ino Page, press MENU.
2. Use the arrow keypad to highlight Restore Ino Deaults.
3. Press ENTER.
Tip:Interestedinseeinghow
faryouvetraveledforamonth,
season,oryear?Ifso,restore
alloftheoptionsexceptthe
DeviceOdometertokeeptrack
ofyourtotalmileage
The Find Page
Usin the Find Pa e
Notes:
Pressabuttonduringasearch
8/3/2019 DeLorme Earthmate GPS PN20 Manual
43/93
42
Using the Find Page
You can use the Find button (the one with a magniying glass) to search or addresses, roads, cities,
points o interest, waypoints, coordinates, and more. There are two Find search options: Find NearMap Center, which is the deault setting, or Find By Name.
Use the Find Near Map Center search option to search or categories o inormation, such as
geographic eatures, waypoints, points o interest, and more, near your current map center. The
number o search results returned is based on available search results, not on distance. Find Near
Map Center searches stop ater 200 search results are ound.
Use the Find By Name search option to search or a specifc location, such as a specifc address or
point o interest. To narrow your search results, you can choose either the Name Contains or Name
Begins With option to search or results that contain or begin with certain characters.
In the Find menu, the option you are currently using is highlighted. The available options are pre-
ceded by Switch to.
To Find a Waypoint
1. Press the Find button. The Find Page displays.2. For a Find Near Map Center search, use the arrow keypad to highlight the Show feld, press
ENTER, select Waypoints, and press ENTER.
OR
For a Find By Name search, use the arrow keypad to highlight the Name feld and press EN-TER. To enter the name, highlight each letter o the name on the keyboard and press ENTER
ater each consecutive letter. Then, highlight OK and press ENTER.
3. Use the arrow keypad to highlight the Symbol feld and press ENTER.
4. Use the arrow keypad to highlight the symbol type you want to search or and press ENTER.For a complete list o all o the symbol types, see AppendixCon page 82.
5. Use the arrow keypad to highlight the search result that you want to fnd and press ENTER.
6. To delete the waypoint, use the arrow keypad to highlight the Delete button and press EN-TER. A confrmation message displays. Use the arrow keypad to highlight the OK button andWaypointsearchresults
tohaltthesearchprocess.
SelectContinue Searchtoresumethesearchprocess.
ToreneaFindByName
search,enterasmuchsearch
criteriaaspossible.Leavethe
Nameeldblanktondallre-
sultsforthesearchcategory
inaspeciedarea.
Findsearchresultsvary
basedonthemapdatatype
youaresearchingwithin.
Toviewthe10mostrecent
Findsearchresults,select
RecentFindsfromtheShow
drop-downlistintheFind
Page.
TheFindPageretainsyour
mostrecentsearchparam-
eters.
press ENTER to delete the waypoint rom the Earthmate GPS PN-20.
OR
The Find Page
8/3/2019 DeLorme Earthmate GPS PN20 Manual
44/93
43
To center the map on the location, use the arrow keypad to highlight the View button andpress ENTER.
OR
To create a route rom your current location to the search result, use the arrow keypad to
highlight the Route button and press ENTER. For more inormation, see ToCreateaRouteon
page 55.
To Find a Point o Interest
1. Press the Find button. The Find Page displays.
2. Press MENU.
3. For a Find Near Map Center search, use the arrow keypad to highlight the Show feld, pressENTER, select Points o Interest, and press ENTER.
OR
For a Find by Name search, use the arrow keypad to highlight the Name feld and press EN-
TER. To enter the name, highlight each letter o the name on the keyboard and press ENTERater each consecutive letter. Then, highlight OK and press ENTER.
Narrow this search by completing one or more o the remaining felds. Highlight the feld and
press ENTER to use the keyboard to enter the search inormation. Then, highlight OK andpress ENTER.
4 To urther narrow your search, use the arrow keypad to highlight the Category feld andpress ENTER. A list o point o interest categories displays. To select a category, use the ar-
row keypad to highlight the category and press ENTER.
5. Use the arrow keypad to highlight the search result that you want to fnd and press ENTER.6. To save the location as a waypoint, use the arrow keypad to highlight the Mark button and
press ENTER. Use the arrow keypad to update the label, coordinates, elevation, and com-
ments. Press ENTER ater you edit each group o inormation.
OR
Note:Notallmapdatatypes
includenaturalfeatures.
Searchingfornaturalresources
withtheFindPage
Searchingforpointsofinterest
withtheFindPage
To center the map on the location, use the arrow keypad to highlight the View button andpress ENTER.
8/3/2019 DeLorme Earthmate GPS PN20 Manual
45/93
44
OR
To create a route rom your current location to the search result, use the arrow keypad to
highlight the Route button and press ENTER. For more inormation, seeToCreateaRouteonpage 55.
To Find Natural Features
1. Press the Find button. The Find Page displays.2. Press MENU.
3. For a Find Near Map Center search, use the arrow keypad to highlight the Show feld, pressENTER, select Natural Features, and press ENTER.
OR
For a Find by Name search, use the arrow keypad to highlight the Name feld and press EN-TER. To enter the name, highlight each letter o the name on the keyboard and press ENTER
ater each consecutive letter. Then, highlight OK and press ENTER.
Narrow this search by completing one or more o the remaining felds. Highlight the feld andpress ENTER to use the keyboard to enter the search inormation. Then, highlight OK andpress ENTER.
4. To urther narrow your search, use the arrow keypad to highlight the Category feld andpress ENTER. A list o natural eature categories displays. To select a category, use the arrow
keypad to highlight the category and press ENTER.
5. Use the arrow keypad to highlight the search result that you want to fnd and press ENTER.
6. To save the location as a waypoint, use the arrow keypad to highlight the Mark button andpress ENTER. Use the arrow keypad to update the label, coordinates, elevation, and com-
ments. Press ENTER ater you edit each group o inormation.
OR
To center the map on the location, use the arrow keypad to highlight the View button andpress ENTER.Naturalresourcesearchresults
Selectinganaturalresource
category
OR
To create a route rom your current location to the search result, use the arrow keypad to
hi hli ht th R t b tt d ENTER F i ti T C t R t
The Find Page
8/3/2019 DeLorme Earthmate GPS PN