16
Installation Guide Update Alert: Firmware updates are posted the web on a regular basis. We recommend on that you check for firmware and/or install guide updates prior to installing this product. Vehicle Application Guide ....... .................. .... ................................. ............................... ...................................................... Key2 ............................................................................................................................................................................. GO Installation s s (Wiring Diagram & Vehicle Wiring Reference Chart ) Installation ................................................. (Wiring Diagram & Vehicle Wiring Reference Chart) ....................................... SmartStart/ 202 Installation Notes.................................................................................................................................. XL Programming Module Programming ...................... ....... ....................................................................... .......... ........................................... Module Reset.. ................................................................................................................................................................ ... Hard ... .... Reset.. ................................................................................................................................................................ Feature & Option List.......................................................................................................................................................... Feature Programming......................................................................................................................................................... LED Diagnostics & Troubleshooting................................................................................................................................... Limited One-Year Consumer ........ Warranty ....................................................................................................................... Quick Reference Guide ............................... ....................................................................................................................... 02 03 04 06 07 09 09 10 10 11 14 15 Index SmartStart Compatible SmartStart is equipped with D2D which means it can be connected to an interface module and used in Range , Extender without a remote starter. Ready ( ) mode the use of See the section for RXT Module Programming more information. ® and their respective companies Jeep Fiat are registered trademarks and property of . The CHRYSLER11 firmware for 2 is an all-in-one door lock and override module compatible DBALL with specific FIAT and JEEP vehicles. This guide supports the installation of a 2 in Range DBALL Extender Ready ( ) mode with an System or a SmartStart (both sold separately). RXT RF Important! This product is compatible with vehicles equipped with a factory-installed remote starter. ONLY Range Extender Ready ( ) is used RXT to dramatically increase the factory remote start activation range compared to the factory transmitter. Refer to the for more information. Quick Reference Guide This module can only be flashed and configured using Xpress at www.directechs.com or using the Directechs VIP Mobile application for smartphones. Refer to for more information. the Module Programming section n on page Rev.: 20170724 Platform: DBALL2 Firmware: CHRYSLER11 ange Extender (RXT) R Ready Installation © 2017 Directed. All rights reserved.

DBALL2-CHRYSLER11-RXT EN IG Z · 7/24/2017  · function programming is selected using Xpress (version 4. or higher). Visit to download the latestVIP 5 version of the application

  • Upload
    others

  • View
    2

  • Download
    0

Embed Size (px)

Citation preview

  • Installation Guide

    Update Alert: Firmware updates are posted the web on a regular basis. We recommendon

    that you check for firmware and/or install guide updates prior to installing this product.

    Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................

    Key2 .............................................................................................................................................................................GO

    Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )Installation .................................................(Wiring Diagram & Vehicle Wiring Reference Chart) .......................................SmartStart/ 202 Installation Notes..................................................................................................................................XL

    ProgrammingModule Programming ...................... .............................................................................. .......... ...........................................Module Reset.. ...................................................................................................................................................................Hard ... ....Reset.. ................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................

    LED Diagnostics & Troubleshooting...................................................................................................................................

    Limited One-Year Consumer ........Warranty.......................................................................................................................

    Quick Reference Guide ......................................................................................................................................................

    02

    03

    0406

    0709091010

    11

    14

    15

    Index

    SmartStart CompatibleSmartStart is equipped with D2D which means it can be connected to an interface module and used in Range,Extender without a remote starter.Ready ( ) mode the use of See the section forRXT Module Programmingmore information.

    ® and their respective companiesJeep Fiat are registered trademarks and property of .

    The CHRYSLER11 firmware for 2 is an all-in-one door lock and override module compatibleDBALLwith specific FIAT and JEEP vehicles. This guide supports the installation of a 2 in RangeDBALLExtender Ready ( ) mode with an System or a SmartStart (both sold separately).RXT RF

    Important!This product is compatible with vehicles equipped with a factory-installed remote starter.ONLY

    Range Extender Ready ( ) is usedRXT to dramatically increase the factory remote start activation rangecompared to the factory transmitter. Refer to the for more information.Quick Reference Guide

    This module can only be flashed and configured using Xpress at www.directechs.com or using the DirectechsVIPMobile application for smartphones. Refer to for more information.the Module Programming section non page

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Vehicle Application GuidePage 2

    The table below lists the vehicles and features which are compatible with this product. Refer to the following pages formore information on installation wiring, programming and troubleshooting for these vehicles.

    * Using the Trunk Release feature will also unlock the vehicle doors.

    Vehicles

    2017

    2016

    2015

    AV

    -Park

    ing

    Lig

    hts

    Contr

    ol

    DL-A

    rmF

    acto

    ryS

    ecurity

    DL-D

    isarm

    Facto

    ryS

    ecurity

    DL-D

    oor

    Lock

    Contr

    ol

    DL-D

    oor

    Unlo

    ck

    DL-T

    runk

    /H

    atc

    hR

    ele

    ase*

    FO

    B-C

    ontr

    olof

    aft

    erm

    ark

    et

    ala

    rmw

    ith

    OE

    Mre

    mote

    Key2G

    O

    RS

    -3x

    LO

    CK

    ST

    AR

    T(S

    tart

    contr

    olusin

    gO

    EM

    Rem

    ote

    )Fiat

    500X (Smart Key) • • • • • • • • • •

    Jeep

    Renegade (Smart Key) • • • • • • • • • • •

    Legend:

    AV: Horn & Lights Controls

    DL: OE Door Lock & Alarm Controls

    RS: Remote Start & Engine Controls

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

    This feature is mandatory to control the immobilizer override in this firmware.

    Key2 has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It usesGOan array of servers to generate a duplicate of the original key, the installation of a remote starter without having toallowinggive up a key.

    The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.

    All Key2 -compatible firmware are clearly indicated in the function list of each vehicle search result page and will alsoGOappear on the flash page. Any first-time user must re-register to gain access to Key2 , and some additional informationGOwill be required to complete the registration process, such as your Directed account number and store name. Key2GOrequires an XKLoader.

    Refer to page 8 of this guide for instructions on how to program features using Key2 .GO

    Page 3

  • Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are NOT DBALL

    Hood Pin

    Remote Start SafetyOverride Switch

    HS CAN High: 3Tan/Black:

    HS CAN Low: 4Tan:

    FT CAN : 5High Orange/Green:

    FT CAN : 6Low Orange/Brown:

    (+) 12V 13Input: Red:

    (-) Ground 14: Black:

    6: White/Black: (-) Hood

    (-) Ground

    B- High:CANBlue, 3pin

    B- :CAN LowWhite, pin 11

    8

    16

    1

    9

    C- High:CANLt. Green, pin 6

    C- :CAN LowBrown, pin 14

    OB IIDDiagnostic Connector

    (+) 12V:Red/Green, pin 16

    Page 4

    Wiring Diagram

    10

    RF

    Prog Button.

    LED

    4

    14

    12

    2

    2DBALL

    You can connect to either a 202XLRFTD a SmartStart module.OR

    Refer to the SmartStart/ 202XLInstallation Notes for more information.

    Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the diagnostic connector.OBDII

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Vehicle Wiring Reference Chart

    B- Low,CAN

    White, pin 11

    B- High,CAN

    Blue, pin 3

    (+) 12V,

    Red/Green, pin 16

    C- Low,CAN

    Brown, pin 14

    C- High,CAN

    Lt. Green, pin 6

    OBDII

    Page 5

    Function Color Pin Polarity Location Color Pins

    C-CAN High Lt. Green 6 Data OBDII diagnostic connector Black 16

    C-CAN Low Brown 14 Data OBDII diagnostic connector Black 16

    B-CAN High Blue 3 Data OBDII diagnostic connector Black 16

    B-CAN Low White 11 Data OBDII diagnostic connector Black 16

    12V Red/Green 16 (+) OBDII diagnostic connector Black 16

    C-CAN High Lt. Green 6 Data OBDII diagnostic connector Black 16

    C-CAN Low Brown 14 Data OBDII diagnostic connector Black 16

    B-CAN High Blue 3 Data OBDII diagnostic connector Black 16

    B-CAN Low White 11 Data OBDII diagnostic connector Black 16

    12V Red/Green 16 (+) OBDII diagnostic connector Black 16

    Wire Information Connector Information

    Fiat 500X (Smart Key) 2016

    Jeep Renegade (Smart Key) 2015-2017

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • SmartStart/ 202 Installation NotesXLPage 6

    Th solution offers ( ) configuration options to control your system; Kit ore Range Extender Ready ( ) two 2DBALL RXT RFThis section provides specific installation information for SmartStart and 202.SmartStart (all sold separately). XL

    The 202 and antenna are not included and be purchased separately.optional XL MUST

    Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE

    4

    4

    XL202

    An

    ten

    na

    XOVER

    SmartStart is and not included. It be purchased separately.optional MUST

    SmartStart is and not included. It be purchased separately.optional MUST

    Configuration Wires (Gray & White)Connect Gray wire to (-) Ground

    5 pins

    D2D (4 pins, white)

    4 pins

    2 pins,not usedCABLE

    CABLE

    The modules must be connected in a specific order. Refer to the section for more information.Module Programming

    1. Use the D2D Crossover ( ) cable that is provided with 202, and the one in the package.XOVER XL NOT DBALL2. The modules must be connected in a specific order. Refer to the section for more information.Module Programming

    The modules must be connected in a specific order. Refer to the section for more information.Module Programming

    SmartStart Revision B

    RF Kit

    RF PKE& CombinationKit

    Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE

    RF PKE BT, & SmartStart CombinationKit

    SmartStart Revision A

    DBALL/2DBALL

    DBALL/2DBALL

    DBALL/2DBALL

    LED

    Prog.Button

    D2D (4 pins, white)

    4 pins

    2 pins,not used

    OR

    SmartStart

    Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop

    LED

    THIS SIDE UP

    LED

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Module ProgrammingPage 7

    Refer to the Diagnostics section on page 11 for more information and for troubleshooting purposes.LED

    Important

    10-pinD2D

    XL202

    10-pinD2D

    SmartStart

    OR

    The module be disconnected from any power source before SmartStart canDBALL mustbe connected to it. Failing to do so could damage .DBALL

    a. To ensure that the D2D communication between SmartStart and works properly, theDBALLGray wire must be connected to a ground source ( SmartStart), and the Brown or BlueRev Bloop must be cut ( SmartStart).Rev A

    b. Do connect the 2-pin harness (on SmartStart). Power and ground will be provided byNOTthe D2D connector.DBALL

    Connect SmartStart to using the D2D port.DBALL

    SmartStart Installation

    Connect 202 to using the D2D port.XL DBALL

    XL202 Installation

    Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.

    Note: Before connecting either the 202 or SmartStart module to , it is important to ensure that the proper feature andXL DBALLfunction programming is selected using Xpress (version 4. or higher). Visit www.directechs.com to download the latestVIP 5version of the application.

    Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

    When the flashing operation is successful, you can proceed with the programming instructions below.

    Flashing a module using your computer:

    1. Connect the interface module to your computer using theXKLoader2.

    2. Go to www.directechs.com using Internet Explorer, andselect the button.Config for RXT

    3. Follow the instructions to select your vehicle, installationtype, and configure your options.

    4. Once you have configured the firmware options, click on theFLASH button.

    Flashing a module using your smartphone or tablet

    1. Connect the interface module to your oader3.XKL

    2. Launch the Directechs Mobile app on your smartphone ortablet.

    3. Select and follow the on screenFLASH YOUR MODULEinstructions.

    1Solid

    Wait until the LED turns solid red.ON

    Note: To skip the transponder programming and use convenience features only, pressthe programming button 5 times. The will turn orange then proceed to step 2.LED

    2

    Press on the Start/Stop button ( ) to turn the ignition (" "PTS ON RUNonceilluminates on Start/Stop switch). The will flashes orange slowly.LED

    Note: If transponder programming was skipped, the turns solid orangeLED ONfor 3 seconds then shuts off once the module is successfully programmedwithout bypass.

    Note: During the programming sequence, the ignition on the car will be turnedON OFFand multiple time automatically.

    3 Press Push-To-Start ( ) button once to turn ignition .PTS OFF ENGINESTARTSTOP PUSH 1x

    &ENGINESTARTSTOP

    PUSH 1x

    Flashes

    Slowly

    You have successfully completed the programming sequence.module

    Go to the next page t complete the programming.o web

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

    You have successfully completed the web programming sequence.

    3

    2

    1

    Once the configuration is completed, reconnect the module.The LED ON solid OFF.turns green for 3 seconds, then turns

    C Olick Submit Key2G Requeston .

    Remove the from the vehicle and reconnect it to your computer. The web site will automaticallymodulerecognize that you are moving onto the second phase of the programming sequence.

    Refer to the LED Diagnostics section on page 11 for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.

    Web Programming (for Key2GO)

    Solid x3 Secs

    &Off

    Page 8

  • Module ResetPage 9

    1If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

    10-pinD2D

    1st

    12-pin14-p

    in

    2nd

    4th

    3rd

    Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

    2

    Solid

    &Release

    3 Release the programming button. The turns solid red.LED ON

    Hard Reset

    2 & &

    1

    Wait 3 seconds until the orange then release theLED turns solidONp The turns solid red.rogramming button. LED ON

    If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

    10-pinD2D

    1st

    12-pin14-p

    in

    2nd

    4th

    3rd

    A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.

    Solid Release Solid

    Solid Flashes

    &Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Page 10

    Feature & Option ListFeature & Option List

    It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options such as and ; however, manualEIPS RXTconfiguration of the features is possible using the information on this page.

    To enter feature programming routine- Turn t , thenhe ignition .ON OFF- Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )

    Programming button.- The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

    the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willuntil .a new command is entered

    Changing feature options- Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/- The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred

    the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

    Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature.- The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED

    indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

    When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

    Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.

    Exiting feature programming- No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON

    sequence.OR

    - Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.

    Feature ProgrammingProgramming

    Button

    * Default Option

    Feat. Operation Flashes/Options Description

    1. No RF Output* Module is connected to a remote starter using a standard installation.

    2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

    3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

    1. OFF* Climate controls return to last setting.

    2. ON Climate controls are automatically set based on temperature.

    RFTD Output Type1

    2

    Automatic climate

    control when

    remote started

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

    LED Description Troubleshooting

    Module has no power.

    Make sure the D2D harness is connected or that the 12 Volt is

    present between the red and black wires. If the 12 Volt is present,

    the module may be defective.

    Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed.

    Initialization failed.Reset the module and complete the programming again. If the issue

    persists, please contact Technical Support.

    Transponder functions were skipped.(If compatible) when RXT mode is not desired or convenience

    features are needed, please reset and reprogram the module.

    All required CAN networks has been detected. Normal operation.

    1 of 2 CAN networks has been detected. Normal operation

    Key2GO initiated.Please follow the steps indicated in “Module programming” to

    complete the Key2GO programming.

    Module was successfully programmed with all

    functions.Normal operation

    Module was successfully programmed without

    transponder functions.Normal operation.

    CAN2 not detected.

    Check the CAN2 Orange/Green and Orange/Brown wire connections.

    Wake up the data bus by turning the ignition on and try again. If your

    installation does not require this connection, skip this step by

    pressing the programming button 5 times.

    J1850 not detected.Check the J1850 wire connection. Wake up the data bus by turning

    the ignition on and try again.

    CAN1 not detected.

    Check the CAN1 Tan and Tan/Black wire connections. Wake up the

    data bus by turning the ignition on and try again. If your installation

    does not require this connection, skip this step by pressing the

    programming button 5 times.

    Bypass data not detected.

    Check the bypass line connection. If more than one wire is used,

    make sure they are not inverted. Ensure the vehicle still operates

    correctly using the factory key.

    Bypass processing error.The bypass calculation failed. Reset the module and try again. If the

    condition persists, please contact Technical Support.

    ISO 1 not detected.

    The Yellow/Black wire did not detect the expected signal. Refer to

    "Installation (wiring diagrams & vehicle wiring reference charts)" to

    check the connections.

    ISO 2 not detected.

    The Orange/Black wire did not detect the expected signal. Refer to

    "Installation (wiring diagrams & vehicle wiring reference charts)" to

    check the connections.

    MUX not detected.

    The Violet/Green or Violet/Brown wire did not detect the expected

    voltage value. Refer to "Installation (wiring diagrams & vehicle wiring

    reference charts)" to check the connections.

    Module Programming

    Module Programming - Error Codes

    Page 11

    LED Diagnostics & Troubleshooting

    Go to the next page to see the rest of the Diagnostics & Troubleshooting.LED

    Solid red

    Flashes redx 1

    Flashes redx 1

    Flashes redx 2

    Flashes redx 3

    Flashes redx 4

    Flashes redx 5

    Flashes redx 6

    Flashes redx 7

    Solid greenx 3 secs

    Flashesgreen

    Solid orange

    Flashes red& green

    Off

    Flashesorange

    Flashesorangeslowly

    Solid orangex 3 secs

  • Page 21

    LED Description Troubleshooting

    OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

    SmartStart features will be limited.

    Ground When Running (Status) command received. The module has initialized the remote start sequence.

    Ignition ON command received.The module has received the Ignition ON command and is

    processing the remote start sequence.

    Start ON command received.The module has received the Start ON command and is

    processing the remote start sequence.

    PTS shutdown error.The PTS output from the module was not activated due to

    safety protection.

    CAN bus incorrectly detected.

    Verify the CAN1 and CAN2 connections. Refer to “Installation

    (wiring diagrams & vehicle wiring reference charts)” to check

    the connections.

    LOCK command received.

    UNLOCK command received.

    TRUNK command received.

    AUX1 command received.

    AUX2 command received.

    AUX3 command received.

    Takeover successful. Normal operation.

    Runsafe was not disabled.No UNLOCK command was received prior to opening the

    door, or the 45 second timer expired in takeover mode.

    Brake was not detected.The brakes were not detected, which prevents the system

    from shutting down the vehicle.

    Smart key was not detected.The smart key was not detected, which prevents the system

    from shutting down the vehicle.

    Speed was detected.The vehicle was detected as moving, which prevents the

    system from shutting it down.

    External module synchronization

    Commands

    Activation Ground When Running (Status)

    If the bypass module fails to flash, it did not receive the

    signal. Commands can come from RF or D2D.

    Shutdown codes

    (Flashes red,red thenorange) x 10

    Flashes red& orange

    Flashes redx 21

    Flashes redx 2

    Flashes redx 4

    Flashes redx 10

    Flashes redx 1

    Flashes redx 3

    Flashesgreen

    Flashesgreenquickly

    Flashesgreen x 1

    Flashesorange x 1

    Flashesorange x 2

    Flashesorange x 3

    Flashesorange x 5

    Flashesorange x 4

    Flashesorange x 6

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

    LED Description Troubleshooting

    Start command received.

    Stop command received.

    Start fail.

    Stop fail.

    RFTD disabled.

    OEM Remote Start Activation was attempted while the RFTD

    feature is disabled. Make sure RXT is selected from the web

    in the flashing process.

    OEM RS disabled.

    The factory remote start option is disabled. Refer to the

    vehicle's owner manual to reactivate the factory remote

    starter.

    If the module fails to flash, it did not receive the signal.

    The RXT start/stop message was received by the module, but

    not executed on the vehicle.

    RXT error codes

    Flashes redx 6

    Flashes redx 8

    Flashes redx 5

    Flashes redx 7

    Flashesgreen x 7

    Flashesgreen x 8

    Page 13

  • Limited Consumer WarrantyOne YearPage 14

    For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.

    This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.

    TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.

    This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com

    920-10012-01 2013-07

    This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.

    Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

    Rev.: 20170724

    Platform: DBALL2

    Firmware: CHRYSLER11 ange Extender (RXT)R Ready Installation

    © 2017 Directed. All rights reserved.

  • Quick Reference GuideDBALL2- Range Extender Ready (RXT)CHRYSLER11 Installation

    © 2017 Directed. All rights reserved.

    Range Extender Ready ( ) is used to amplify the distance coveredRXTby factory remote starters. The interface connects to the vehicle anduses the same code as the factory remote to remote start the vehicle.The runtime and features are identical to the remote starter.OEMSome of the advantages of are greater remote range and 2-wayRXTcompatibility.

    Range Extender Ready ( )RXT

    Command Engine Result

    Start NOT running. The engine will be started.

    Start Running. The engine will be stopped.

    The following table describes the behavior of the vehicle in relation to the RXTfeature. The following commands are performed on the aftermarket remote.

    Runtime

    T equivalent to the amount set for the , canhe runtime is remote starter whichOEMbe modified in some vehicles (refer to your vehicle owner’s manual for moreinformation).

    Runtime Reset

    T s return the runtime to its predefinedhe Runtime Reset feature allow the user tovalue. This can only performed per remote start.ONCE

    RXT Operations

    Vehicle Takeover

    4

    3

    1 Press the remote start button on the transmitter to*start the vehicle.

    2

    Press putthe brake pedal, the carin gear and drive off.

    Enter the vehicle, while making sure thefactory remote is inside with you.

    Press t Push-to-Start ( ) .he buttonPTST Push-to-Start ( ) starthe button willPTSto flash.

    Press the Unlock button on the factoryor aftermarket remote.*

    Ready todrive off

    Pressremote start

    *button

    Press Unlockonbutton

    either remote*

    OR

    * Your aftermarket remote may differ from the model shown in the illustrations.

    Enter vehiclewith Smart Key

    Pit Stop/idle Mode

    The vehicle pit stop/idle mode feature is not available in this firmware.

    &

    Flashes

    ENGINESTARTSTOP

    ENGINESTARTSTOP

    PUSH 1x

  • Quick Reference GuideDBALL2- Range Extender Ready (RXT)CHRYSLER11 Installation

    © 2017 Directed. All rights reserved.

    Button(s) Actions

    Press & hold for 1 second to lock.

    Press & hold for 1 second to unlock.

    Press & hold for 1 second to remote

    start.

    Press & hold for 5 seconds to activate

    the trunk release (optional).

    Press once, then to activate the

    rear hatch/tail glass release (optional).*

    Press 3 times, then to activate

    the panic mode.

    Press once, then to reset the

    remote starter runtime.

    List of Available Commands

    x1 +

    x3 +

    x1 +

    * This output is configurable. see your authorized installation center for moreinformation.

    Note that the information below is for Viper, Clifford and Python models. Icons andcommands may differ depending on the remote brand and model purchased. Referto your authorized installation center for more information.

    SmartStart Compatible

    This system is compatible with Directed SmartStart 3.0. Fora complete list of supported features, please visitwww.mysmartstart.com.

    What is SmartStart?

    Now you can remote start, lock and unlock your car just by pushing a button onyour smartphone; using the SmartStart App from Directed, the leader in vehiclesecurity and remote start. The simple graphical interface gives you control over thefollowing features of your installed remote start or security with remote start system:

    � Lock/Arm� Unlock/Disarm� Remote Car Starter� Trunk Release� Panic� Aux Channels

    You can also control multiple vehicles – great for families – and assign more thanone user to control a vehicle. It's easy with SmartStart!

    But, this is only the beginning! SmartStart is loaded with additional featuresincluding tracking, SmartSchedule, vehicle status, roadside assistance, homeGPScontrol, parked car finder and more.

    3.0 enables a "Cloud-Connected Car" like never before, providing an entirely newlevel of 2-way interaction with your vehicle. Connectivity is managed through theDirected Cloud Services ( ) network linking car, app, end user, and the Internet.DCS

    For more information, visit www.mysmartstart.com.

    Notes