Datasheet P011.26 Rev. 3 - ANVILEX · • No electrolytic capacitors used • Wide range supply voltage 18 ... • Active gate pull-down if no supply voltage ... CC No load connected

P011.26Single channel low cost gate driver board for IHM and IHMB IGBT module

Revision: 3; Date: 15.03.2014

© 2011-2014 ANVILEX Technologies UG All right reserved. Page 1

General description

This device is a ready to use low cost compact single-channel

advanced gate driver board designed to control wide range of high

power medium-voltage 130mm and 190mm IHM and IHMB IGBT

modules of various manufacturers with rated collector-emitter volt-

age of 1700V and rated collector current up to 3600A. The gate

driver board is suitable for chopper, two- and multi-level and many

others known applications. The gate driver board features a fiber

optic interface. Advanced control and protection functions are in-

cluded and allow the design of high reliability systems. Balancing

technology of positive and negative gate supply voltages allows

reliable switching behaviors over under wide range of loads. Free

access to the fastening screws of the IGBT module base plate

allows checking fastening torques without removal of the gate

driver board.

Applications

• General purpose low-/medium-voltage inverters

• Multilevel inverters

• Resonant converters

• Wind power generation

• Solar power generation

• Industrial AC and DC motor drives

• Uninterruptible power supplies (UPS)

• Switched-mode power supplies (SMPS)

• Power factor correctors (PFC)

• Active filters (AF)

• Induction overheating

• Radiology and laser technology

• Research

• Traction

• Railroad power supplies

• Welding

• Static Synchronous Compensator (STATCOM)

Features

• Ready to use gate driver board for IHM and IHMB module

• Suitable for 130mm and 190mm IHM and IHMB IGBT module

• Suitable for chopper, two- and multi-level inverter topologies

• Small form factor

• Direct mounting onto IGBT module

• High reliability, long life

• No electrolytic capacitors used

• Wide range supply voltage 18…28 VDC

• No stabilized supply voltage required

• Opposite supply voltage polarity protection

• Isolated DC/DC converter

• Monitoring of supply voltage

• Fiber optic links for control and fault status signals

• Switching frequency from DC to 10 kHz

• Duty cycle from 0% to 100%

• Gate peak current up to 35 A

• Monitoring of gate voltage at on-state

• Positive and negative gate voltage balancing

• IGBT module short-circuit protection

• Active Miller clamp feature

• Active gate pull-down if no supply voltage present

• Passive VCE clamping at turn-off

• Optional two steps turn-off with adjustable level and delay

• Reliable desaturation detection at low VCE voltage

• Fault status output

• UVLO protection

• Safe isolation according EN 50178

• Allows free access to the fastening screws of IGBT module




Important notice

Please read these instructions for use carefully and keep them for later use, be sure to make them accessible to other users and observe infor-

mation they contain.

Trademarks and brands

All named trademarks or/and brands are the property of their respective owners.

Caution and safety warnings

• Handling all high-voltage equipment involves risk of live.

• Any handling of IGBT module and gate driver board is subject to the general specification for protecting electrostatic sensitive devices accord-

ing to international standard IEC 60747-1, Chapter IX or European standard EN 100015. If these specifications are not followed, both IGBT

module and gate driver board may be damaged.

• Pay attention to clearance and creepage distances between parts with different voltage potentials (e.g. busbar, heatsink, mechanical suspen-

sion etc.).

• Pay attention to fastening torques and insertion/retention forces, polarity of gate driver supply voltage, polarity of power terminals.

• Dirtiness and/or mechanical damages (e.g. oxidation, scratches, delaminating of coating) on gate driver board and IGBT module may dramati-

cally decrease isolation properties of it and may cause permanent damage of the gate driver board and IGBT module.

• To avoid pollution of fiber optic connectors protective rubber plugs must be removed directly before insertion of fiber optic cables.

• Never remove protective rubber plugs of fiber optic connectors, connect/disconnect fiber optic cables on both gate driver board and control

equipment until supply voltage of gate driver board applied.

• Never connect or disconnect power supply connector until supply voltage applied on it. This handling may cause permanent damage of the

gate driver board.

• Avoid permanent damage of the gate driver board, personal and equipment injury, never remove protective rubber plugs of fiber optic connec-

tors, connect or disconnect fiber optic cables at both gate driver board and control equipment sides, connect or disconnect power supply con-

nector of the gate driver board until voltage across collector and emitter of IGBT module applied.

• Application of gate driver board with improper IGBT module may cause permanent damage to the gate driver board and/or IGBT module.

• Application of gate driver board with damaged or defected IGBT module may cause permanent damage of the gate driver board or affect gate

driver board reliability.

• Save fiber optic cables from damaging by sharp corners, heat parts, etc., pay attention on bending radius. Damaged fiber optic cable can

cause malfunction or/and damage or permanent lost of equipment and human life.

• HFBR-1521Z LED transmitters are classified as IEC 60825-1 Accessible Emission Limit (AEL) Class 1 based upon the current proposed draft

scheduled to go into effect on 1st January 1997. AEL Class 1 LED devices are considered eye safe.

Absolute maximum ratings

Stresses beyond those listed under “Absolute maximum ratings” may cause permanent damage to the gate driver board. These are stress rat-

ings only, functional operation of the gate driver board under these or any other conditions beyond those indicated in the operational sections of

the specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect gate driver board reliability.

Table 1. Absolute maximum ratings.

Parameter Symbol Conditions Min. Typ. Max. Units

Input supply voltage VCC Applied to 24V and 0V power supply termi-nals.

-30 - +30 V

Collector-emitter voltage VCE Applied to C and E terminals. - - 1463 V

Gate-emitter voltage VGE Applied to G und E terminals. -17 - 17 V

Gate peak current IG - - 40 A

P011.26Single channel low cost gate driver board for IHM und IHMB IGBT module




Switching frequency fSW Output power must not exceed maximal al-lowed output power.

- - 15 kHz

Output power PG - - 5 W

Isolation test voltage VISO(Pri/Sec) Applied between primary to secondary side terminals, 50 Hz, 1 min, According EN 50178.

- - 4000 V

Operating peak voltage VOP(Pri/Sec) Applied to primary and secondary side termi-nals.

- - 1700 V

Operating ambient temperature TA 0 - 65 °C

Storage ambient temperature TS -40 - 90 °C

Recommended operations conditions

Table 2. Recommended operations conditions.


Input supply voltage VCC Applied to 24V and 0V power supply termi-nals.

18 24(1) 28 V

Collector-emitter voltage VCE Applied to C and E terminals. - - 1200 V

Switching frequency fSW Output power must not exceed maximal al-lowed output power.

0 - 10 kHz

Output power PG - - 4 W

Duty cycle D 0 - 100 %

Operating ambient temperature TA 0 - 55 °C

Note 1. To increase withstand to possible disturbances of supply voltage (e.g. voltage dips, oscillations, interferences) we recommend to use

24V supply voltage as supply voltage for gate driver board.

Insulation characteristics

Table 3. Insulation characteristics.


Pollution degree - According to DIN VDE 0110, 1/89. 2 -

Maximum working isolation voltage VIORM Applied between primary and secondary side terminals.

2000 - - V

Highest allowable over voltage VIOTM Applied between primary and secondary side terminals.

4000 - - V

Insulation and safety related specification

Table 4. Insulation and safety related specification.


Isolation testing voltage VISO(PRI/SEC) Applied between primary and secondary side terminals, 50 Hz, 1 min, According EN 50178.

4000 - - V

Input-Output coupling capacitance CISO(PRI/SEC) f = 1 MHz, measured between power supply terminal X1 and output terminals C, G, E. Total capacitance given for both channel.

- 3.6 - pF

Input-Output coupling resistance RISO(PRI/SEC) VIO = 1000V 400 - - MΩ

Partial discharge extinction voltage VE 50 Hz, QPD ≤ 10 pQ, According to IEC 60272. 2000 - - V





Minimum external air gap (clearance) between primary and secondary side

dA(PRI/SEC) Shortest distance through air measured be-tween primary potential island to secondary potential island. According to IEC 60664-1 and EC 50124-1.

19.10 - - mm

Minimum external tracking (creepage) between primary and secondary side

dS(PRI/SEC) Shortest path along body and surface meas-ured from primary potential island to secon-dary potential island. According to IEC 60664-1 and EC 50124-1.

19.10 - - mm

Minimum internal insulation gap (internal clearance) primary and secondary side

dI(PRI/SEC) Through insulation distance conductor to conductor, usually the straight line distance thickness between the primary and secondary windings of isolation transformer.

0,93 - - mm

Tracking resistance(Comparative tracking index)

CTI DIN IEC 112 / VDE 0303 Part 1. 175 - 400 V

Isolation material group - According to DIN VDE 0110, 1/89 Table 1. IIIa -

Electrical specifications (DC)

Unless otherwise noted, all typical values at VCC = 24 V DC, TA = 25 °C. All minimum/maximum values are at conditions listed under “Recom-

mended operating conditions”.

Table 5. Electrical DC specification.


Input supply voltage VCC Applied to 24V and 0V supply input terminals. 18 24 28 V

Quiescent supply current ICC No load connected to gate output, off-state. - 66 - mA

Startup supply voltage VCC(START) Full functionality not guaranteed until VCC out of specified range 18V…28V.

- - 16.0 V

Supply voltage under voltage lockout VCC(UVLO) 15.5 - - V

Startup time tSTART - 10 50 ms

Steady on-state, no switching. 15.0 15.3 15.6 VGate-Emitter voltage at on-state VGE(ON)

fSW = 10 kHz, PG = 4 W 14.4 15.0 - V

Steady off-state no switching. -7.5 -7.8 -8.1 VGate-Emitter voltage at off-state VGE(OFF)

fSW = 10 kHz, PG = 4 W -7.0 -7.5 - V

Desaturation threshold voltage VCE(DESAT) - 7.5 - V

VUVLO(LO) - 10 - VGate-Emitter under voltage threshold

VUVLO(HI) - 11 - V

Active Miller clamp voltage VCLAMP - 2.0 - V

Gate pull-down voltage VPULL_DOWN No power supply voltage present or under specified startup level.

- 3.0 - V

High level output current IOH - - 35 A

Low level output current IOL - - 35 A

Maximum output power PG 4 - - W




Switching specifications (AC)

Unless otherwise noted, all typical values at VCC = 24 V DC, TA = 25 °C. All minimum/maximum values are at conditions listed under “Recom-

mended operating conditions”.

Table 6. Switching AC specification.


Switching frequency fSW PG < 4 W - - 10(1) kHz

Duty cycle D 0 - 100 %

tCTRL(ON) 240 - - nsMinimal control signal width

tCTRL(OFF) 180 - - ns

Propagation delay time at turn-on. tP(ON) - 580 - ns

Propagation delay time at turn off. tP(OFF) - 530 - ns

Dead time tDT - 0(2) - ns

Desaturation sense time tDESAT - 7270(3) - ns

Desaturation sense time to error signal delay

tDESAT(FB) - 7000 - ns

Gate-Emitter under voltage sense time tUV - TBD - ns

Gate-Emitter under voltage sense to feedback signal delay

tUV(FB) - 140 - ns

Output high level common mode tran-sient immunity

|CMH| 75 - - kV/µs

Output low level common mode transient immunity

|CML| 75 - - kV/µs

Note 1. The maximum switching frequency depends on the IGBT gate charge.

Note 2. Dead time insertion not implemented.

Note 3. Desaturation time can be adjusted on request.

Optical interface specifications

Unless otherwise noted, all typical values at TA = 25 °C.

Table 7. Optical interface specification.


Standard fiber optic cable. - - 15 mFeedback signal transmit distance L

Improved fiber optic cable. - - 19 m

Fiber optic receiver - Control signal fiber optic connector. HFBR-2521Z -

Fiber optic transmitter - Feedback signal fiber optic connector. HFBR-1521Z -

Mechanical specifications

Unless otherwise noted, all typical values at TA = 25 °C.

Table 8. Mechanical specification.


Dimensions - L × W × H, Typical, see outline drawing. 194.0 × 45.0 × 14.5(1), (2) mm

Weight m - 40 - g

Single wire. 0.2 - 4.0 mm2Allowable cross section of power supply wire

SPOWER

Stranded wire. 0.2 - 2.5 mm2





Mounting torques of IGBT module termi-nals

MIGBT IGBT module terminals, M4 screw. 1.0(3) - 3.0(3) Nm

Fiber optic connector insertion force FI - 8 30 N

Fiber optic connectors retention force FR 7 8 - N

Note 1. Maximal components height (measured from bottom side of printed circuit board) on the top side of driver board 10.0 mm.

Note 2. Maximal components height (measured from bottom side of printed circuit board) on the bottom side of driver board 4.5 mm.

Note 3. Given fastening torques related to the gate driver board. Consult IGBT module datasheet to determinate minimum and maximum re-

quired mounting torques.

Timing diagrams

VCE(SAT)

Light on

Active Miller clamp

VGE

ControlLight off

Light on

Light offFault

Inactive

Active

VCE

VDC

VGH

VGL

tPD(OFF)tPD(ON)

tCTRL(ON)

VGE(CLAMP)

VGE(TH)

tCTRL(OFF)

Figure 1. Normal condition turn-on and turn-off process.




VCE(DESAT)

Light on

Active Miller clamp

VGE

ControlLight off

Light on

Light offFault

Inactive

Active

VCE

VDC

VGH

VGL

tPD(ON)

tCTRL(ON)

tPD(ON)

tPD(DESAT)

tPD(FS) tPD(FR)

VGE(CLAMP)

tCTRL(OFF)

Figure 2. Desaturation protection turn-off process.

Light on

VGE

ControlLight off

Light on

Light offFault

VGH

VGH

VGL

tPD(ON)

tCTRL(ON)

VGH

VUVLO(LO)

VUVLO(HI)

VGE(TH)

tUV

tUV(FB)

Figure 3. Undervoltage turn-off process.




Detailed description

The device is an ready to use low cost compact single-channel advanced gate driver board. They designed to control wide range of high power

medium-voltage 130mm and 190mm IHM and IHMB IGBT module of various manufacturers with rated collector-emitter voltage of 1700V and

rated collector current up to 3600A. The gate driver board suitable for chopper, two- and multi-level and many others known applications. The

gate driver board features a fiber optic interface. Advanced control and protection functions are included and allow the design of high reliability

systems. Special developed balancing technology of positive and negative gate supply voltages allows reliable switching behaviors over under

wide range of loads. Free access to the fastening screws of IGBT module base plate allows checking fastening torques without removal of the

gate driver board.

The gate driver board receives control signal via fiber optical connector mounted in the middle of the gate driver board. The input is triggered by

the edge of control optic signal. Connected to the gate driver board IGBT going on, when input control optic signal (light) present. The input

control signal pulse width TCTRL(ON) must be larger than the minimal pulse width, shorter control signals are ignored. Input signals longer than

minimal pulse width are transmitted to the gate of IGBT module after the delay TPD(ON) with minimum width distortion. This timing also valid for

the input control signal width TCTRL(OFF). To prevent partial turn-on and/or partial turn-off of IGBT short input control signals should be avoided

and not generated by control equipment. The minimal width of the input control signals differ by the used IGBT module and application and

should be experimentally estimated in each application case.

The gate driver board does not insert any dead time delays to the input control signal. Dead time delays insertion must be provided by customer

control equipment to prevent possible cross conduction condition of IGBT module. Typical turn-on and turn-off processes are shown on the

Figure 1.

The output stage of gate driver board is able to sink and source current of 40A over the full temperature range. Separated turn-on and turn-off

gate resistors as well as active miller clamp resistor allow independent gate charge and discharge control. By default, recommended by IGBT

module manufacturer values of the turn-on and turn-off resistors recalculated to +15.0V/-7.5V gate voltages are used. All available product con-

figurations listed in the section “Remove safety rubber plugs inserted into fiber optic connectors. Insert plugs of fiber optic cable to the gate

driver board connectors. To avoid pollution of fiber optic connectors safety rubber plugs must be removed directly before insertion of fiber optic

cable plugs. Safety rubber plugs must be inserted back directly after disconnection of fiber optic cable plugs. Pay attention to fiber optic cable

function, insertion and retention forces. Never connect or disconnect fiber optic connectors at gate driver board and/or control equipment sides

until supply voltage at gate driver board and/or voltage across collector and emitter of IGBT module applied.

Save fiber optic cables from damaging by sharp corners, heat parts, etc., pay attention on bending radius. Damaged fiber optic cable can cause

malfunction or/and damage or permanent lost of equipment and human life.

Ordering information”. To meet application and EMC requirements turn-on and turn-off gate resistors can be adjusted on request. Gate driver

boards also available without mounted gate resistors to allow application specific adjustments.

Optional two level turn-off is used to increase application reliability during overcurrent state. During turn-off, gate voltage can be reduced to a

programmed level and time in the order to reduce the IGBT current (in event of overcurrent). This action avoids both dangerous overvoltage

across the IGBT, and RBSOA problems, especially at short circuit turn-off. By default two level turn-off disabled, please contact us if this option

required.

Innovative active Miller clamp function allows the control of the Miller current during a high dV/dt situation and prevents unexpected turn-on of

IGBT. During turn-off, the gate voltage is monitored and the clamp output is activated when gate voltage goes below 2V relative emitter poten-

tial. The clamp function is disabled when the input light signal goes active again.

Desaturation protection ensures the protection of IGBT in the event of overcurrent. When the collector-emitter voltage goes higher desaturation

threshold, after a blanking time the output of the gate driver board is driven low and the fault status output is activated. By enabled 2-level turn-

off feature 2-level turn-off process is used. The fault state is exited at the next rising edge of control input signal. Depending on used IGBT mod-

ule and application desaturation threshold and blanking time can be adjusted on request.

Undervoltage detection (UVLO) protects the IGBT in the event of a insufficient positive gate supply voltage (during startup and fault situation).

During undervoltage, the output of the gate driver board is active pull-down until positive gate supply voltage remains higher than 2V. Passive

pull-down is used for the positive gate supply voltage below 2V. Fault status output signal the undervoltage state and is reset only when under-

voltage state disappears. Typical undervoltage turn-off process is shown on Figure 3.




Fault status output of the gate driver board is used to signal fault condition (desaturation, UVLO) to a control equipment. Fault condition signaled

via fiber optical connector mounted in the middle of the gate driver board. Reactions of the fault status signal on the different faults conditions

are shown on the Figure 1, Figure 2 and Figure 3.

Active gate pull-down feature prevents unexpected turn-on of IGBT if no power supply of the gate driver boards present. Then VGE voltage reach

level around 3V the active gate pull-down circuit going active and pull-down gate of IGBT.

Electrical configuration

C

E

C'

G

E'

IGBT ModuleGate Driver Board

DC Power Supply

Customer Control Unit

Fiber Optic Link

Fiber Optic Link

FC

FF C

G

ETwisted Wire Connection X1:24V

X1:0V

FC

FF

24V

0V

Figure 4. Recommended application circuit.

Interface description

Figure 5. Interface component layout.

Table 9. Interface description.

Designation Media type Function

Power supply

X1:24V electric Supply input 24V DC

X1:0V electric 0V DC

Control and feedback status signals

FC fiber optic Optical control signal input

FF fiber optic Optical fault status signal output

IGBT signals

C electric IGBT collector signal

G electric IGBT gate signal

E electric IGBT emitter signal




Mechanical dimensions

Figure 6. Mechanical dimensions of gate driver board (all dimensions in millimeter).

Maximal components height (measured from bottom side of printed circuit board) on the top side of driver board 10.0 mm.

Maximal components height (measured from bottom side of printed circuit board) on the bottom side of driver board 4.5 mm.

Mounting instructions

IGBT module and gate driver board are electrostatic sensitive devices. Any handling of IGBT module and gate driver board is subject to the

general specification for protecting electrostatic sensitive devices according to international standard IEC 747-1, Chapter IX or European stan-

dard EN 100015. If these specifications are not followed, both IGBT module and gate driver board may be damaged.

The gate driver board can be easily mounted onto an IGBT module by screwing the corresponding terminals. Pay attention to mounting torques.

Dirtiness and mechanical damages on gate driver board may dramatically decrease isolation properties and may cause permanent damage of

the driver board and attached IGBT module.

Connect the connector X1 of the gate driver board to the power supply unit. Fix connector receipt using two integrated screws to prevent unex-

pected disconnection during operation. Pay attention to polarity of supply voltage and mounting torques. Never connect or disconnect power

supply connector X1 under applied supply voltage.

Remove safety rubber plugs inserted into fiber optic connectors. Insert plugs of fiber optic cable to the gate driver board connectors. To avoid

pollution of fiber optic connectors safety rubber plugs must be removed directly before insertion of fiber optic cable plugs. Safety rubber plugs

must be inserted back directly after disconnection of fiber optic cable plugs. Pay attention to fiber optic cable function, insertion and retention

forces. Never connect or disconnect fiber optic connectors at gate driver board and/or control equipment sides until supply voltage at gate driver

board and/or voltage across collector and emitter of IGBT module applied.

Save fiber optic cables from damaging by sharp corners, heat parts, etc., pay attention on bending radius. Damaged fiber optic cable can cause

malfunction or/and damage or permanent lost of equipment and human life.

Ordering information

Application of gate driver board with improper IGBT module may cause permanent damage to the gate driver board and/or IGBT module. Appli-

cation of gate driver board with damaged or defected IGBT module may cause permanent damage of the gate driver board or affect to gate

driver board reliability.

Table 10. Ordering information.

Manufacturer(1)

IGBT module type(1) IGBT module case VCE, V IC, A Part order number(2)

ID

ABB AG5SNA 2400E120100 IHM 190mm 1200 2400 P011.26-5SNA2400E120100-V1

ID:22031




Manufacturer(1)


ID


ID:22034

ABB AG5SNA 1600N170100 IHM 130mm 1700 1600 P011.26-5SNA1600N170100-V1

ID:22029

ABB AG5SNA 1600M170100 IHM 130mm 1700 1600 P011.26-5SNA1600M170100-V1

ID:22028


ID:22030


ID:22032


ID:22033


ID:22035


ID:61115

DYNEXDIM1800ESM12-A IHM 190mm 1200 1800 P011.26-DIM1800ESM12-A-V1

ID:61122

DYNEXDIM1800ESS12-A IHM 190mm 1200 1800 P011.26-DIM1800ESS12-A-V1

ID:61123


ID:26406


ID:61124


ID:61125


ID:26407

FUJI Electric1MBi 1200U4C-120 IHM 130mm 1200 1200 P011.26-1MBi1200U4C-120-V1

ID:22355

FUJI Electric1MBi 1200VC-120P IHM 130mm 1200 1200 P011.26-1MBi1200VC-120P-V1

ID:26385


ID:22387


ID:26389


ID:26391

FUJI Electric1MBi 2400U4D-120 IHM 190mm 1200 2400 P011.26-1MBi2400U4D-120-V1

ID:26393


ID:61342

FUJI Electric1MBi 2400VD-120P IHM 190mm 1200 2400 P011.26-1MBi2400VD-120P-V1

ID:26395


ID:26397

FUJI Electric1MBi 3600VD-120 IHM 190mm 1200 3600 P011.26-1MBi3600VD-120-V1

ID:26399


ID:22356

FUJI Electric1MBi 1200VC-170E IHM 130mm 1700 1200 P011.26-1MBi1200VC-170E-V1

ID:26386




Manufacturer(1)


ID

FUJI Electric1MBi 1200VR-170E IHM 130mm 1700 1200 P011.26-1MBi1200VR-170E-V1

ID:61341


ID:22388

FUJI Electric1MBi 1600VC-170E IHM 130mm 1700 1600 P011.26-1MBi1600VC-170E -V1

ID:26390

FUJI Electric1MBi 1600VR-170E IHM 130mm 1700 1600 P011.26-1MBi1600VR-170E -V1

ID:61343


ID:26392


ID:26394

FUJI Electric1MBi 2400VC-170E IHM 130mm 1700 2400 P011.26-1MBi2400VC-170-V1

ID:61340

FUJI Electric1MBi 2400VD-170E IHM 190mm 1700 2400 P011.26-1MBi2400VD-170E-V1

ID:26396

FUJI Electric1MBi 2400VR-170E IHM 130mm 1700 2400 P011.26-1MBi2400VR-170e-V1

ID:61344

FUJI Electric1MBi 2400VS-170E IHM 190mm 1700 2400 P011.26-1MBi2400VS-170E-V1

ID:61345


ID:26398

FUJI Electric1MBi 3600VD-170E IHM 190mm 1700 3600 P011.26-1MBi3600VD-170E-V1

ID:26400

FUJI Electric1MBi 3600VS-170E IHM 190mm 1700 3600 P011.26-1MBi3600VS-170E-V1

ID:61346

Infineon AGFZ1200R12HP4 IHM 130mm 1200 1200 P011.26-FZ1200R12HP4-V1

ID:61425

Infineon AGFZ1200R12HE4 IHM 130mm 1200 1200 P011.26-FZ1200R12HE4-V1

ID:61431


ID:61426

Infineon AGFZ1800R12HP4_B9 IHM 190mm 1200 1800 P011.26-FZ1800R12HP4_B9-V1

ID:61427

Infineon AGFZ1800R12HE4_B9 IHM 190mm 1200 1800 P011.26-FZ1800R12HE4_B9-V1

ID:61432


ID:61428


ID:61429

Infineon AGFZ2400R12HE4_B9 IHM 190mm 1200 2400 P011.26-FZ2400R12HE4_B9-V1

ID:61433


ID:61430


ID:

Infineon AGFD600R16KF4 IHM 130mm 1600 600 P011.26-FD600R16KF4-V1

ID:

Infineon AGFD600R17KE3_B2 IHM 130mm 1700 600 P011.26-FD600R17KE3_B2-V1

ID:

Infineon AGFD600R17KF6C_B2 IHM 130mm 1700 600 P011.26-FD600R17KF6C_B2-V1

ID:




Manufacturer(1)


ID

Infineon AGFD800R17KE3_B2 IHM 130mm 1700 800 P011.26-FD800R17KE3_B2-V1

ID:

Infineon AGFZ800R17KF6 IHM 130mm 1700 800 P011.26-FZ800R17KF6-V1

ID:

Infineon AGFZ800R17KF6C_B2 IHM 130mm 1700 800 P011.26-FZ800R17KF6C_B2-V1

ID:

Infineon AGFD800R17KF6C_B2 IHM 130mm 1700 800 P011.26-FD800R17KF6C_B2-V1

ID:

Infineon AGFD800R17HP4-K_B2 IHMB 130mm 1700 800 P011.26-FD800R17HP4-K_B2-V1

ID:

Infineon AGFZ1200R17KE3 IHM 130mm 1700 1200 P011.26-FZ1200R17KE3-V1

ID:

Infineon AGFZ1200R17KE3_B2 IHM 130mm 1700 1200 P011.26-FZ1200R17KE3_B2-V1

ID:

Infineon AGFD1200R17KE3-K IHM 130mm 1700 1200 P011.26-FD1200R17KE3-K-V1

ID:

Infineon AGFD1200R17KE3-K_B2 IHM 130mm 1700 1200 P011.26-FD1200R17KE3-K_B2-V1

ID:


ID:


ID:

Infineon AGFZ1200R17HP4 IHMB 130mm 1700 1200 P011.26-FZ1200R17HP4-V1

ID:

Infineon AGFZ1200R17HP4_B2 IHMB 130mm 1700 1200 P011.26-FZ1200R17HP4_B2-V1

ID:

Infineon AGFD1200R17HP4-K_B2 IHMB 130mm 1700 1200 P011.26-FD1200R17HP4-K_B2-V1

ID:61420

Infineon AGFD1200R17HE4 IHMB 130mm 1700 1200 P011.26-FD1200R17HE4-V1

ID:61421


ID:


ID:


ID:

Infineon AGFD1600/1200R17KF6C_B2 IHM 190mm 1700 1600 P011.26-FD1600/1200R17KF6C_B2-V1

ID:


ID:


ID:

Infineon AGFD1600/1200R17HP4_B2 IHMB 190mm 1700 1600 P011.26-FD1600/1200R17HP4_B2-V1

ID:


ID:


ID:


ID:


ID:




Manufacturer(1)


ID


ID:

Infineon AGFZ1800R17HE4_B9 IHMB 190mm 1700 1800 P011.26-FZ1800R17HE4_B9-V1

ID:61422


ID:


ID:


ID:


ID:


ID:


ID:

Infineon AGFZ2400R17HE4_B9 IHMB 190mm 1700 2400 P011.26-FZ2400R17HE4_B9-V1

ID:61423


ID:


ID:


ID:

Infineon AGFZ3600R17KE3_B2 IHM 190mm 1700 3600 P011.26-FZ3600R17KE3B2-V1

ID:


ID:


ID:

Infineon AGFZ3600R17HE4 IHMB 190mm 1700 3600 P011.26-FZ3600R17HE4-V1

ID:61424

IXYS GmbHMIO 1800-17E10 IHM 190mm 1700 1800 P011.26-MIO1800-17E10-V1

ID:26412

IXYS GmbHMIO 2400-17E10 IHM 190mm 1700 2400 P011.26-MIO2400-17E10-V1

ID:26413

JSC ElectrovipryamitelMTKI-3600-06 IHM 190mm 600 3600 P011.26-MTKI-3600-06-V1

ID:


ID:


ID:

JSC ElectrovipryamitelMTKI-800-12H IHM 130mm 1200 800 P011.26-MTKI-800-12H-V1

ID:

JSC ElectrovipryamitelMTKI-800-12F IHM 130mm 1200 800 P011.26-MTKI-800-12F-V1

ID:


ID:


ID:


ID:




Manufacturer(1)


ID

JSC ElectrovipryamitelMTKI-1200-12K IHM 130mm 1200 1200 P011.26-MTKI-1200-12K-V1

ID:

JSC ElectrovipryamitelMTKI-1200-12KT IHM 130mm 1200 1200 P011.26-MTKI-1200-12KT-V1

ID:


ID:


ID:


ID:


ID:


ID:


ID:


ID:


ID:


ID:


ID:


ID:


ID:

JSC ElectrovipryamitelMTKI-800-17T IHM 130mm 1700 800 P011.26-MTKI-800-17T-V1

ID:

JSC ElectrovipryamitelMDTKI-1200-17 IHM 190mm 1700 1200 P011.26-MDTKI-1200-17-V1

ID:

JSC ElectrovipryamitelMDTKI-1200-17-2 IHM 190mm 1700 1200 P011.26-MDTKI-1200-17-2-V1

ID:

JSC ElectrovipryamitelMDTKI-1200-17-2T IHM 190mm 1700 1200 P011.26-MDTKI-1200-17-2T-V1

ID:


ID:


ID:

JSC ElectrovipryamitelMDTKI-1200-17T IHM 190mm 1700 1200 P011.26-MDTKI-1200-17T-V1

ID:


ID:


ID:


ID:


ID:


ID:




Manufacturer(1)


ID


ID:


ID:


ID:


ID:


ID:


ID:


ID:

MITSUBISHICM1200HCB-34N IHM 130mm 1700 1200 P011.26-CM1200HCB-34N-V1

ID:26401

MITSUBISHICM1800HC-34H IHM 190mm 1700 1800 P011.26-CM1800HC-34H-V1

ID:26402


ID:26403

MITSUBISHICM2400HC-34H IHM 190mm 1700 2400 P011.26-CM2400HC-34H-V1

ID:26404


ID:26405

Powerex Inc.CM1200HCB-34N IHM 130mm 1700 1200 P011.26-CM1200HCB-34N-V1

ID:26401

Powerex Inc.CM1800HC-34H IHM 190mm 1700 1800 P011.26-CM1800HC-34H-V1

ID:26402


ID:26403

Powerex Inc.CM2400HC-34H IHM 190mm 1700 2400 P011.26-CM2400HC-34H-V1

ID:26404


ID:26405

Xi'an Yongdian Electric Co., Ltd.YMIF800-12 IHM 130mm 1200 800 P011.26-YMIF800-12-V1

ID:61116


ID:61117


ID:61118


ID:61119


ID:61120


ID:61121

Note 1. If IGBT module manufacturer or IGBT module missing in ordering information table, please contact ANVILEX Technologies UG for more

information.

Note 2. By default gate driver boards equipped with gate resistors recommended by manufacturer of IGBT module. If differ values of gate resis-

tors required, please contact ANVILEX Technologies UG for customer specific version of gate driver board. To order gate driver board without

gate resistors please use order code: P011.02-BASIC.




Disposal

Please dispose product in accordance with the directive 2002/96/EG – WEEE (Waste Electrical and Electronic Equipment). If you have any

question, please refer to the local authorities responsible for waste disposal.

Terms and conditions of usage

The data contained in this product data sheet is exclusively intended for technically trained staff. Handling all high-voltage equipment involves

risk of live. You and your technical departments will have to evaluate the suitability of the product for the intended application and the complete-

ness of the product data with respect to such application.

All HFBR-1521 LED transmitters are classified as IEC 825-1 Accessible Emission Limit (AEL) Class 1 based upon the current proposed draft

scheduled to go into effect on 1st January 1997. AEL Class 1 LED devices are considered eye safe. For more information contact the ANVILEX

GmbH directly or the sales office which is responsible for you.

This product data sheet describes the characteristics of this product for which a warranty is granted. Any such warranty is granted exclusively

pursuant the terms and conditions of the supply agreement. There will be no guarantee of any kind for the product and its characteristics.

Should you require additional product information to the data given in this product data sheet or which concerns the specific application of our

product, please contact the ANVILEX GmbH. directly or the sales office, which is responsible for you. For those that are specifically interested

application notes are provided.

Due to technical requirements our product may contain dangerous substances. For information on the substances in question please contact

the ANVILEX GmbH directly or the sales office, which is responsible for you.

Should you intend to use the product in health or life endangering or life support applications, please notify.

ANVILEX GmbH reserves the right to make any technical modification of products and/or change this product data sheet without notice at any

time in the course of product improvement.

Revision history

Rev. Page Description

0 all 1. Initial issue.

1 all 1. Description of active gate pull-down feature added.2. Several typographic mistakes fixed.

2 - 1. Table 8 updated.2. Figure 5 updated.3. Figure 6 updated.4. Ordering information updated.

3 - 1. Ordering information for FUJI Electric module added.2. Ordering information for MITSUBISHI module added.3. Ordering information for JSC Electrovipryamitel module added.4. Ordering information for IXYS GmbH module added.5. Ordering information for ABB AG module added.6. Ordering information for DYNEX module added.7. Ordering information for Xi'an Yongdian Electric Co., Ltd. IGBT module added.8. Ordering information for Powerex Inc. module added.

All rights reserved. Technical changes reserved. For misprint is no liability assumed.

© 2011-2014 ANVILEX Technologies UG

Address: Enderstrasse 94, Building C, 01277 Dresden, GermanyPhone: 0049 351 40945521Fax: 0049 351 40945524Internet: http://www.anvilex.comE-Mail: [email protected] store: http://shop.anvilex.com

Documents

Datasheet P011.26 Rev. 3 - ANVILEX · • No electrolytic capacitors used • Wide range supply voltage 18 ... • Active gate pull-down if no supply voltage ... CC No load connected