Data sheet

DH-SMT/SI ED.96.N6.02 © Danfoss 12/2008 1

Electrical actuatorsAMB 162, AMB 182

AMB 162 and AMB 182 actuators are used for temperature control in central heating systems together with 3-way and 4-way rotary valves of the types HRB and HFE.

The actuators are applicable with: - Controllers with 3-point outlet (e.g. ECL)- Controllers with standard voltage or current output (e.g. ECL)

Main data:. 24 V or 230 V. 3-point control. Voltage signal of 0-10 V or 2-10 V (factory setting: 2-10 V).. With or without adjustable actuator limit

switches

A 2m wire is supplied with the actuators.

Description

Ordering Type Supply voltage Torque Speed Control signal Remark Code No.

AMB 162

24 V a.c.

5 Nm

140 s

3-point

- 082G4030

S* 082G4031

230 V a.c.

70 s-

082G4032

140 s082G4034

S* 082G4035

670 s-

082G4040

24 V a.c./V d.c. 140 s 0-10 V 082G4050

AMB 182

24 V a.c./V d.c. 15 Nm140 s

0-10 V -082G4055

280 s 082G4056

24 V a.c.10 Nm 70 s

3-point-

082G4062

15 Nm 280 s 082G4064

230 V a.c.

10 Nm 70 s 082G4067

15 Nm 280 s082G4069

S* 082G4079* Actuator with built-in auxiliary signal switch

Two couplings (linkage kits) are delivered with the actuators:- 082G4235 (MS-NRE6-D) , to be used with HRB valves- 082G4230 (MS-NRE), to be used with HFE valves

Accessories

Type Designation Code No.

AUX switch Auxiliary signal switch 082G4012

2 ED.96.N6.02 © Danfoss 12/2008 DH-SMT/SI

Data sheet Actuator AMB 162 and AMB 182

Technical data Supply voltage 24 V a.c./V d.c. or 230 V a.c., 50/60 Hz

Power consumption 2.5 VA (5 Nm) and 3.5 VA (10/15 Nm)

Operating torque 5, 10, or 15 Nm

Wire 2 m (3 × 0.5 mm2)

Actuator limit switch 2 A/250 V a.c.

Control mode 3-point or 0-10 V/2-10 V

Rotation angle Electrically limited to 90°

Manual operation Mechanical disengagement

Ambient temperature (during operation) 0 °C … +50 °C

Transport and stock temperature −10 °C … +80 °C

Protection class II (without earthing wire)

Enclosure IP 42

Weight AMB 162: 0.46 kgAMB 182: 0.54 kg

- marking in acc. with standardsLow Voltage Directive 73/23/EEC, EMC-Directive 2004/108/EEC:EN 60730-1, EN 60730-2-14

Installation The actuators can be mounted directly on the rotary valve by means of the supplied mounting kit.

The rotating angle is limited to 90° and when the actuator reaches the actuator limit, the voltage supply to the actuator is disconnected.

Application principle

Boiler system with ECL electronic controller and HRB rotary valve.

Linkage

Mounting kit Make Type Code No.

MS-NRE

Danfoss HFE (HRE old, HRB old)

082G4230ESBE

MG, G, F, T, TM

H, HG

TA VRTE

Termomix B, C, D

Sauter MH32, MH42

MS-NRE6-D Danfoss HRB 082G4235

MS-NRC CENTRA ZR, DR 082G4255

MS-NRL L&G VCI 31, VBG 31, VBF 21 082G4270

Ordering (continuous)

DH-SMT/SI ED.96.N6.02 © Danfoss 12/2008 3

Data sheet Actuator AMB 162 and AMB 182

Wiring 3-point control

1 = brown, 2 = blue, 3 = white + AUX switch

0-10 V

1 = black, 2 = red, 3 = white, 4 = whiteY = input signalU = output signal

Dimensions

N L 24 V a.c./ 24 V d.c.*/

* valid only for some actuators - see ordering section

4 ED.96.N6.02 Prepared by Danfoss A/S © 12/2008

Data sheet Actuator AMB 162 and AMB 182