Data kit Manual Stationary Version 1.1 · 2018. 12. 23. · Globalstar Data Kit Manual - Stationary Version 1.1 3/2001 2 WINDOWS 95, 98 INSTALLATION Please note that some of the windows

STATIONARY UNIT

VERSION 1.1

Globalstar Data Kit Manual - Stationary

Version 1.1 3/2001 1

Globalstar Data Kit Welcome. Your Globalstar Data Kit is your wireless link to the Internet. Please review the following before beginning the installation of your new modem. A. WHATS IN THE KIT? • GSP-2900 data cable with RS232 interface residing in the Network Interconnect

Device box. • CD Containing software applications and a detailed QUALCOMM Globalstar Packet

Data Users Guide (see section E) B. WHAT ELSE DO YOU NEED? • Globalstar GSP-2900 Stationary unit • Operating systems :Windows 95, 98, NT or 2000; Macintosh; Red Hat Linux; Solaris

UNIX • Grounding equipment is required – not included. C. GETTING STARTED Windows 95, 98, NT, 2000 • Before you begin, make sure the following are installed on your computer: TCP/IP

protocol and Dial-Up Networking for 95/98 or Remote Access Services (RAS) for NT/2000. (For help, see your Windows documentation.)

• See appropriate section below for a detailed explanation of the set-up process for each of the Windows platforms.

UNIX • Follow the instructions in the Users Guide (or see section D).

Index Page Windows 95, 98, 98SE 2 Windows 2000 & ME 9 Windows NT 4 16


Version 1.1 3/2001 2

WINDOWS 95, 98 INSTALLATION Please note that some of the windows in Windows 95 and Windows 98 first edition will be different then the ones shown in the screens shown below. Place the CD into your CD Rom Drive. The CD will bring up the following window, if it does not, double click on My Computer on your desktop and then on the CD ROM icon which will produce the following window;

• Click on the “Install Packet Modem Drivers” This screen will appear:

• Click on the “Next”


Version 1.1 3/2001 3

This screen will appear:

• After reading and agreeing with the License Agreement, Click the “Yes” button This screen will appear:

• Click the “Begin Modem Install” This screen will appear:

• Click on the “Add” button


Version 1.1 3/2001 4


• Select the “Other” button and click “Next” This screen will appear:

• Ensure there is a check in the box beside the “Don’t run the Hardware Installation

Wizard” This screen will appear:

• Ensure that there is a check in the box beside “Don’t detect my modem, I will select it

from a list”


Version 1.1 3/2001 5


• Click the “Have Disk…” This screen will appear:

• Click the “Browse” button This screen will appear:

• Click the CD ROM drive in the “Drives” window located at the bottom of the screen • Highlight the “gstardata.inf” file • Click “OK”


Version 1.1 3/2001 6


• Click the “OK” button This screen will appear:

• Highlight the “QUALCOMM Globalstar Phone Modem for Stationary Unit” • Click the “Next” button


• Highlight Com port (COM1) or whatever your selected com port is • Click “Next”


Version 1.1 3/2001 7


• Click on “Finish” This screen will appear:

• Click on “Close”


• Click on the “Finish”


Version 1.1 3/2001 8

This screen will appear

• Click on the “OK” button and your machine will reboot Your Modem has now been successfully installed.


Version 1.1 3/2001 9

WINDOWS 2000 and ME INSTALLATION Please note that some of the Windows in 2000 will be different then the ones shown in the screens shown below. Place the CD into your CD Rom Drive. The CD will bring up the following window, If it does not, Double Click on My Computer on your desktop and than on the CD ROM icon which will produce the following window:

• Click the “Install Packet Modem Driver” This screen will appear:

• Click on the “Next” button


Version 1.1 3/2001 10


• Once you have read and agree with the License agreement, click on the “Yes” button


• Once you have read this screen, Click on the “Begin Modem Install” This screen will appear:

• Click the “Add” button


Version 1.1 3/2001 11


• Select the “Other” button • Click on “Next” button


• Ensure there is a check in the box beside “Don’t run the Hardware Installation Wizard”

• Click on “Next” button This screen will appear:

• Ensure there is a check in the box beside “Don’t detect my modem, I will select from a list”

• Click the “Next” button


Version 1.1 3/2001 12


• Click on “Have Disk…” button This screen will appear:

• Click on “Browse..” button This screen will appear:

• Click on the CD ROM drive in the “Drives” window located at the bottom of the screen

• Highlight the “gstardata.inf” • Click the “OK” button


Version 1.1 3/2001 13



• Highlight “QUALCOMM Globalstar Phone Modem for Stationary Unit” • Click the “Next” button


• Click on your “COM1” communications port or whatever port you have connected your phone to



Version 1.1 3/2001 14


• Click the “Finish” button This screen will appear:

• Click the “Close” button This screen will appear:

• Click the “Finish” button


Version 1.1 3/2001 15


• Click the “OK” button and your machine will reboot Your Modem has now been successfully installed.


Version 1.1 3/2001 16

WINDOWS NT 4 INSTALLATION Ensure that RAS services and TCP/IP services are installed before you start your installation. Place the CD into your CD ROM Drive. The CD will bring up the following window. If it does not, Double Click on My Computer on your desktop and than on the CD ROM icon which will produce the following window:

• Click the “Install Packet Modem Drivers” This screen will appear:



Version 1.1 3/2001 17


• Once you have read and agree with the License agreement, Click the “Yes” button This screen will appear:

• Once you have read this screen, Click the “Begin Modem Install” This screen will appear:

• Click the “Add” button


Version 1.1 3/2001 18


• Ensure there is a check in the box for “Don’t detect my modem: I will select it from a list”

• Click the “Next” button This screen will appear:

• Click the “Have Disk….” button This screen will appear:

• Click the “Browse..” button


Version 1.1 3/2001 19


• Highlight the “Gstarpacket1_0” • Click the “Open” button



• Highlight “QUALCOMM Globalstar Phone Modem for Staionary Unit” • Click the “Next” button


Version 1.1 3/2001 20


• Select the “Selected ports” button • Highlight “COM1” or whatever port you have the Qualcomm Globalstar phone

connected to • Click the “Next” button


• Click the “Finish” button This screen will appear:

• Click the “Close” button


Version 1.1 3/2001 21


• Click the “Yes” button


• Click the “Add” button This screen will appear:

• Click the “OK’ button This screen will appear:

Click the “Continue” button Your Modem has now been successfully installed.

Documents

Data kit Manual Stationary Version 1.1 · 2018. 12. 23. · Globalstar Data Kit Manual - Stationary Version 1.1 3/2001 2 WINDOWS 95, 98 INSTALLATION Please note that some of the windows