dalyi Klean - northwest.com.mx fileTypical Technical daTa pROdUcT daTa SheeT REGULATORY COMPLIANCE Consolideck® DailyKlean is compliant with all national, state and district VOC regulations

Typical Technical daTa

pROdUcT daTa SheeT

REGULATORY COMPLIANCEConsolideck® DailyKlean is compliant with all national, state and district VOC regulations.

dailyKleaneconomical daily maintenance cleaner for concrete floors

Product Data Sheet • Page 1 of 4 • Item #46030 • CDDK - 041510 • ©2010 PROSOCO • www.consolideck.com

OvERvIEwConsolideck® DailyKlean is a specially designed concentrated maintenance cleaner for concrete floors, including floors hardened and densified with lithium-silicate products.

This specialized blend of degreasers and detergents removes most common soiling deposited on concrete floors daily. It’s ideal for concrete floors everywhere, from warehouses and manufacturing plants to schools, stores, hospitals, restaurants and more.

Though DailyKlean is specifically made for floors hardened and densified with Consolideck® LS® lithium-silicate hardener/densifier, it’s perfect for almost any concrete floor.

Used as part of a comprehensive maintenance program, DailyKlean helps ensure the highest appearance and performance standards for all indoor concrete flatwork.

SPECIFICATIONSFor all PROSOCO product specifications visit www.prosoco.com and click on “SpecBuilder” or “Solution Finder.”

ADvANTAGES• Maintains concrete floor shine.• Removes most common soiling.• Flexible dilution for both surface and deep

cleaning.• Readily biodegradable; low toxicity.• Contains U.S. EPA DfE (Design for the

Environment) conformant CleanGredients® listed surfactants.

• Concentrated for economy of storage and transport.

• No rinsing needed for routine surface cleaning of floors.

• Ideal for auto scrubbers.

Limitations• May not remove some embedded stains.• Does not contain lithium-silicate. Has no

hardening/densifying effect.

FORM Clear blue liquidfresh, clean odor

SPECIFIC GRAVITY .999

pH 8.6

WT/GAL 8.32 lbs.

ACTIVE CONTENT NA

TOTAL SOLIDS NA

VOC CONTENT <1%

FLASH POINT >200°F (93°C) ASTM D 3278

FREEZE POINT 31°F (-0.5°C)

SHELF LIFE 2 yrs in factory-sealed container

03 00 00 Concrete03 01 30.51 Cleaning of Cast-In-Place Concrete

03 30 00 Cast-In-Place Concrete09 00 00 Finishes

09 01 60 Maintenance of Flooring

APPLICATIONBefore use, read “Preparation” and “Safety Information.” ALWAYS TEST for suitability, dilution rates and desired results before overall application. Test using the following application instructions. Let surface dry thoroughly before inspection.

DilutionNormal Cleaning• Dilute 1 oz of cleaner per 1-gal fresh water

Deep Cleaning• dilute 2 oz of cleaner per 1-gal fresh water

PAX Dilution• dilute one 4 oz PAX per 5-gal fresh water

Application Instructions1. Apply with a mop or automatic scrubber. 2. For routine surface cleaning, rinsing the

concrete floor is not necessary. Mop up spent cleaner and dissolved contaminants, or vacuum up with auto scrubber.

After deep-cleaning, rinse well with fresh water. Do not let puddles or concentrated cleaner dry on the floor.

3. Buff the cleaned floor with a white pad to increase the shine.

CleanupClean tools and equipment using fresh water.


PREPARATIONSweep or vacuum to remove loose materials from the surface to be cleaned.

Pre-clean oil spots or other deep stains with the appropriate Consolideck® product. For recommendations, call Customer Care toll-free at 800-255-4255.

Surface and Air TemperaturesCleaning effectiveness is reduced when surface and air temperatures fall below 50°F (10°C).

Do not apply at temperatures below 40°F (4°C).

EquipmentApply with mop or auto scrubber.

Storage and HandlingStore in a cool, dry place. Always seal container after dispensing. Do not alter or mix with other chemicals.

Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperatures of 45-100°F (7-38°C). Do not double stack pallets.

Dispose of unused product and container in accordance with local, state and federal regulations.

SAFETY INFORMATIONConsolideck® DailyKlean is a commercial strength concentrated cleaner and may cause irritation. Field-diluted solution may cause eye and skin irritation. Use appropriate safety equipment and job site controls during application. Read full label and MSDS for precautionary instructions before use.

First AidIngestion: Do not induce vomiting. Get immediate medical assistance.

Eye Contact: Rinse thoroughly for 15 minutes. Get medical assistance.

Skin Contact: Rinse thoroughly. Get medical attention if irritation persists.

Inhalation: Remove to fresh air. Get medical attention as necessary.

24-Hour Emergency Information: INFOTRAC at 800-535-5053

alWayS TeSTALWAYS TEST a small area of each surface to confirm suitability and desired results before starting overall application. Test with the same equipment, recommended surface preparation and application procedures planned for general application.

dailyKleanpROdUcT daTa SheeT

BeST pRacTiceS


wARRANTYThe information and recommendations made are based on our own research and the research of others, and are believed to be accurate. However, no guarantee of their accuracy is made because we cannot cover every possible application of our products, nor anticipate every variation encountered in masonry surfaces, job conditions and methods used. The purchasers shall make their own tests to determine the suitability of such products for a particular purpose.

PROSOCO, Inc. warrants this product to be free from defects. Where permitted by law, PROSOCO makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness for particular purpose. The purchaser shall be responsible to make his own tests to determine the suitability of this product for his particular purpose. PROSOCO’s liability shall be limited in all

events to supplying sufficient product to re-treat the specific areas to which defective product has been applied. Acceptance and use of this product absolves PROSOCO from any other liability, from whatever source, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict liability. This warranty may not be modified or extended by representatives of PROSOCO, its distributors or dealers.

CUSTOMER CAREFactory personnel are available for product, environment and job-safety assistance with no obligation. Call 800-255-4255 and ask for Customer Care technical support.

Factory-trained representatives are established in principal cities throughout the continental United States. Call Customer Care at 800-255-4255, or visit our web site at www.prosoco.com for the name of the Consolideck® representative in your area.

For spot cleaning heavily soiled areas, begin testing DailyKlean at a dilution of 2-ounces of cleaner concentrate to 1-gallon of fresh water.

Do not use dilutions stronger than 4-oz cleaner concentrate to 1-gallon of fresh water. Always use the mildest effective dilution possible.

To remove deeply embedded oil and grease stains, test Consolideck® Oil & Grease Stain Remover.

Use soft brushes/soft pads with auto scrubbers. Never use aggressive brushes or pads on polished concrete.

Use DailyKlean as part of a comprehensive maintenance program that includes deep cleaning with Consolideck® lsKlean Super Concentrate at least once a week.

Never go it alone. If you have problems or questions, contact your local PROSOCO distributor or field representative. Or call PROSOCO technical Customer Care, toll-free at 800-255-4255.




Datos técnicos habituales

caRacteRÍsticas Del PRoDucto

Cumplimiento reglamentarioCumplimiento con VOCConsolideck® lsGuard® cumple con los siguientes reglamentos VOC de AIM nacionales, estatales y de distrito

X Agencia de Protección Ambiental de los Estados Unidos

X Distritos de SCM de la Junta de Recursos del Aire de California

X Distrito de Control de Calidad del Aire de la Costa Sur

X Condado Maricopa, AZ

X Comisión de Transporte de Ozono del Noreste

lsGuard®

sellador brilloso, endurecedor y densificador para concreto

Hoja de información del producto • Página 1 de 4 • Artículo No. 46073 • CDLSG - 022010 • ©2010 PROSOCO • www.consolideck.com

DeSCripCiÓn generalConsolideck® lsGuard® combina belleza de alto brillo con un endurecedor de silicato de litio de alto rendimiento. La fórmula de este copolímero mejora el brillo y el endurecimiento de la superficie, la resistencia a manchas de pisos de concreto convencional, de concreto endurecido o de cemento terrazo. Las superficies tratadas con lsGuard® resisten el daño del agua y de la abrasión de la superficie.

Ideal para aplicarse a concreto gris o de color estándar, Consolideck® lsGuard® protege y mejora la intensidad del color del concreto de color integral o con manchas de color. lsGuard® provee un acabado de alto brillo y larga duración que maximiza el reflejo de la luz y elimina la necesidad de ceras para piso, líquidos para pulir y revestimientos convencionales de resina.

Consolideck® lsGuard® no activará ni contribuirá a la ASR (Reacción Álcali-Silicato) de la superficie.

eSpeCifiCaCioneSPara conocer todas las especificaciones de los productos PROSOCO, visite www.prosoco.com y haga clic en “SpecBuilder” o en “Solution Finder”.

VentaJaS• Poco olor. Fácil de aplicar. Secado rápido.• Produce un piso de concreto con un acabado de

alto brillo y duradero con máximo reflejo de la luz.

• Elimina la necesidad de ceras para piso, líquidos para pulir y revestimientos convencionales de resina.

• Mejora el brillo y el endurecimiento de la superficie, y la resistencia a manchas de pisos tratados con Consolideck® LS® o Consolideck® LS/CS®.

• Mejora y protege Consolideck® GemTone ColorCoats y SafetyColors.

• Ha sido probado y cumple con las normas de Colaboración de California para la Calidad del Aire Interior de las Escuelas de Alto Rendimiento. Su uso contribuye a LEED® para puntos escolares (Crédito EQ 4).

• No contribuirá al agrietamiento de la superficie. El alto contenido de litio combate el ASR de la superficie.

• El brillo y la dureza no reducen la resistencia ante deslizamientos.

• Respirable y estable a los rayos UV. No se tornará de color amarillo, tampoco se decolorará, pelará ni descascarará.

• Cumple con VOC. No inflamable. No tóxico. Poco olor.

• Compatible con Consolideck® GemTone ColorCoats y SafetyColors.

Limitantes• Sólo para uso en interiores.

03 30 00 Concreto colado in situ03 35 00 Acabado para concreto

09 60 00 Para pisos09 61 00 Tratamientos para pisos

FORMA líquido blanco lechoso

GRAVEDAD ESPECÍFICA 1,11

pH 11,0

PESO/GALONES 9,2 lbs (4,2 k)

CONTENIDO ACTIVO 22%

TOTAL SÓLIDOS 22%

CONTENIDO COV < 100 g/L

PUNTO DE INFLAMACIÓN ND

PUNTO DE CONGELACIÓN 32°F (0°C)

VIDA ÚTIL 1 año en un contenedor sin abrir sellado de fábrica

Componentes no alimenticiosPrograma listado R2Registro No. 142261

Consolideck® Cleaner/Degreaser • suciedad en general • grasa y aceite

Consolideck® Oil & Grease Stain Remover • manchas de aceite y grasa profundamente arraigadas

Después de aplicar el limpiador, enjuague exhaustivamente con agua. En caso de usarse un limpiador/decapante a base de D-limoneno, limpie las superficies tratadas con el Consolideck® Cleaner/Degreaser y enjuague exhaustivamente.

El concreto manchado con ácido debe neutralizarse y enjuagarse exhaustivamente antes de la aplicación.

La aplicación se puede comenzar una vez que las superficies preparadas estén secas y sin agua estancada.

Temperaturas de la superficie y del aireLas temperaturas de aplicación deben estar entre 40 y 100°F (de 4 a 38°C).

EquipoAplique el producto con atomizador de baja presión y un trapeador de microfibra o sintético que no deje pelusas. No rociar.

Almacenamiento y manejoAlmacene el producto en un lugar fresco y seco. Siempre selle el contenedor después de usarlo. No lo altere ni lo mezcle con otros productos químicos. La vida útil publicada supone que el almacenamiento de los contenedores sellados de fábrica es en posición vertical en un lugar seco. Mantenga temperaturas de 40 a 100°F (de 4 a 38°C). Evite la congelación. No apile más de una capa de tarimas. Deseche el producto de acuerdo con los reglamentos locales, estatales y federales.


preparaCiÓnProteja a las personas, vehículos, propiedades, plantas y todas las superficies no diseñadas para recibir Consolideck® lsGuard® producto, salpicaduras y corrientes de aire. Use polietileno u otro material de protección aprobado.

No aplique el producto a superficies que estén congeladas, sucias o tengan agua estancada.

NOTA DEL FABRICANTE: Para evitar que se traspase la humedad del planchado del concreto, se debe incluir una barrera impermeable en la construcción del piso.

Concreto existenteSe puede aplicar Consolideck® lsGuard® a concreto curado existente de cualquier edad. Las superficies deben estar limpias y firmes estructuralmente. Elimine todos los materiales extraños, inclusive las juntas de refuerzo, agentes de curado, grasa y aceite de superficie y residuos de construcción usando el limpiador de preparación de superficies Consolideck® que se enlista a continuación:

Consolideck® SafStrip • curación y sellos • pintura • revestimientos de alta resistencia

Consolideck® SafEtch®* • lechada de concreto • suciedad de construcción *No debe usarse en concreto que haya sido tratado con Consolideck® LS®, LS/CS® o lsGuard®.

Consolideck® Wax & Cure Remover • ceras, selladores y revestimientos • curación y sellos bajos en sólidos

Consolideck® Cure & Seal Remover • curación y sellos altos en sólidos

Consolideck® Concrete Floor Restorer • suciedad en general • óxido y otras manchas metálicas • revestimientos de cera ligeros

apliCaCiÓnAntes de aplicar el producto, lea el apartado “Preparación” e “Información de seguridad”.

SIEMPRE PRUEBE cada superficie para comprobar su manejo y los resultados deseados antes de la aplicación general. Utilice las siguientes instrucciones de aplicación. Deje que se seque completamente la superficie antes de la inspección y aprobación.

DisoluciónNo diluya al aplicar a concreto curado o a concreto curado y pulido mate.

Al aplicarlo a concreto pulido o altamente pulido, dilúyalo con una parte de agua como máximo.

Cantidades de coberturaLas variaciones en la calidad, la porosidad, las condiciones del sitio de la obra, la temperatura y la humedad relativas del concreto afectarán las cantidades de cobertura y los tiempos de secado. Calcule la Cantidad de cobertura destino realizando una prueba a una sección representativa de la superficie utilizando las siguientes instrucciones.

Cantidades de cobertura estimadasSe ofrece las siguiente cantidad de cobertura exclusivamente para hacer estimaciones. Consulte a continuación las instrucciones sobre cómo calcular las cantidades de cobertura destino específicas de proyectos.

• 1500 a 2000 pies2 (139 a 186 m2) por galón de EE.UU.

sieMPRe haGa una PRuebaSIEMPRE PRUEBE en un área pequeña de cada superficie para comprobar su manejo y los resultados deseados antes de aplicar el producto en su totalidad. Pruebe con el mismo equipo, la misma preparación recomendada para las superficies y los mismos procedimientos planeados de aplicación para la aplicación general.

lsGuard®


MejoRes PRácticas


Cómo calcular las cantidades de cobertura destino específicas de proyectos1. Prepare la sección de prueba de acuerdo a la

sección “Preparación” arriba mencionada. Las superficies deben estar limpias, secas y absorbentes.

2. Agregue 1 galón (3,8 litros) de lsGuard® a un atomizador de bombeo limpio que tenga una punta para rociar de 0,5 gpm. Aplique una capa ligera conforme a las siguientes Instrucciones de aplicación. Para lograr el acabado deseado, repita la aplicación cuantas veces sea necesario.

3. Mida el área de prueba para establecer la Cantidad de cobertura destino por galón. Después de aplicar lsGuard®, proteja el área de prueba de la humedad por 72 horas.

Instrucciones de aplicación Se puede aplicar Consolideck® lsGuard® a superficies de concreto alisado con palustre de acero, pulido, pulido mate o altamente pulido. Para obtener los mejores resultados, dé tratamiento a los pisos con Consolideck® LS® o LS/CS® antes de la aplicación de lsGuard®.

1. Moje ligeramente una almohadilla de micro fibras limpia con lsGuard®, exprima el excedente y deje la almohadilla húmeda.

2. Trabajando de una unión de control a la otra, aplique una capa fina de lsGuard® a una pequeña sección del piso utlizando un atomizador de bombeo limpio que tenga una punta para rociar de 0,5 gpm.

3. Utilizando la almohadilla de micro fibras húmeda y ejerciendo una firme presión hacia abajo, rocíe inmediatamente el lsGuard® para producir una capa delgada y uniforme. Mientras permanezca húmedo, extienda el producto lo más posible. Aplicado adecuadamente, lsGuard® seca rápidamente. Evite seguir esparciendo una vez que empiece el secado. Evita rociar excesivamente.

4. Deje que seque sin quedar pegajoso, normalmente de 20 a 60 minutos.

5. Tan pronto seque, bruña lsGuard® utilizando una bruñidora de alta velocidad con una almohadilla bruñidora de calor Consolideck® o con una almohadilla adecuada para pulir que se utilice en acabados de alto brillo. Además de suavizar y de pulir la superficie tratada, el bruñir a alta velocidad calienta el lsGuard® para que el tratamiento se funda con y se adhiera al concreto para mayor durabilidad y longevidad. Inmediatamente después de bruñir, la temperatura de la superficie debe llegar a 90,5°F (32,5°C).

6. Repita los pasos 1 al 5 de arriba cuantas veces sea necesario para obtener el acabado deseado. Bruña entre capa y capa. Para obtener el máximo brillo, aplique hasta tres capas.

Bajo condiciones normales, la superficie está lista para el tráfico 1 hora después de bruñir. Evite se exponga al agua por 72 horas.

LimpiezaAntes de que seque el producto, limpie las herramientas y el equipo con agua potable. Enjuague inmediatamente con agua potable el rociado excesivo de las superficies de vidrio, aluminio, pulidas y otras superficies.

Resultados finalesEl piso estará listo para usarse cuando esté seco.

Al secarse, las superficies lisas y endurecidas deben mostrar poca absorción de agua y el brillo deseado. La máxima resistencia al agua se desarrollará en 7 días.

MantenimientoBarra el piso diariamente con una almohadilla de micro fibras o con un trapeador para polvo. Siempre que sea necesario, seque el ladrillo con una máquina bruñidora de alta velocidad para renovar el brillo.

Si bien lsGuard® mejora la resistencia de los pisos de concreto a las manchas, algunas sustancias ácidas, incluyendo alimentos, pueden grabar el piso y manchar. Limpie TODOS los derrames tan pronto como sea posible.

Las superficies que serán tratadas deben estar limpias, secas y absorbentes. Compruebe la permeabilidad de la superficie rociando agua ligeramente – las superficies designadas para tratamiento deben humedecerse uniformemente.

El concreto manchado con ácido debe neutralizarse y enjuagarse exhaustivamente antes de aplicar Consolideck® lsGuard®.

Para obtener los mejores resultados, dé tratamiento a los pisos con Consolideck® LS® o LS/CS® antes de la aplicación de Consolideck® lsGuard®.

Para la máxima durabilidad y resistencia a las manchas, bruña el lsGuard® recién aplicado con una bruñidora de alta velocidad utilizando almohadillas para pulir y obtener acabados de alto brillo. Los mejores resultados se obtienen cuando al bruñir el piso alcanza una temperatura de o superior a los 90,5°F (32,5°C) inmediatamente después.

Para darle mantenimiento a los pisos tratados con Consolideck®, simpre utilice Consolideck® ls Klean Super Concentrate. Los limpiadores de piso convencionales pueden contener ingredientes que quitan el alto brillo de los acabados. lsKlean Super Concentrate no contiene ácidos, alcalinos, solventes ni abrasivos irritantes. Sí contiene el penetrante silicato de litio para ayudar a conservar la dureza e intensidad de los pisos tratados con Consolideck®.

Nunca lo haga solo. Si tiene algún problema o pregunta, comuníquese con el distribuidor o con el representante PROSOCO de su localidad. O llame al número gratuito 800-255-4255 del área técnica del departamento de Atención a clientes de PROSOCO.

lsGuard®



Contacto con la piel: Lave el área expuesta con jabón y agua. No intente neutralizar el producto con agentes químicos. Si persiste la irritación, busque atención médica.

Ingestión: Beba grandes cantidades de agua o leche. No inducir el vómito. Busque atención médica inmediatamente.

Inhalación: Lleve a la persona afectada a tomar aire fresco. Lave la boca y las vías nasales con agua reiteradamente. Si persisten las dificultades para respirar, busque atención médica.

Información en caso de emergencia las 24 horas: INFOTRAC al 800-535-5053

garantÍaLa información y las recomendaciones hechas se basan en nuestra propia investigación y en la investigación de otras personas y se consideran precisas. Sin embargo, no garantiza su precisión porque no podemos cubrir cada posible aplicación de nuestros productos, ni anticipar la variación encontrada en las superficies de mampostería, las condiciones de trabajo y los métodos utilizados. Los compradores deben hacer sus propias pruebas para determinar si dichos productos son adecuados para un propósito particular.

PROSOCO, Inc. garantiza que este producto no tiene defectos. Donde lo permita la ley, PROSOCO no otorga ninguna otra garantía con respecto a este producto, explícita o implícita, incluyendo sin limitación las garantías implícitas de comercialización o adecuación para un propósito particular.

El comprador será responsable de hacer sus propias pruebas para determinar si este producto es adecuado para su propósito particular. La responsabilidad de PROSOCO estará limitada en todo caso a suministrar el producto suficiente para volver a tratar las áreas específicas a las cuales se aplicó el producto defectuoso. La aceptación y el uso de este producto absuelven a PROSOCO de cualquier otra responsabilidad, de cualquier fuente, incluyendo la responsabilidad por daños incidentales, causales o resultantes, ya sea debido al incumplimiento de garantía, negligencia o responsabilidad estricta. Esta garantía no puede ser modificada ni ampliada por los representantes de PROSOCO, sus distribuidores ni sus proveedores.

atenCiÓn al ClienteEl personal de la fábrica está disponible para brindarle ayuda con relación al producto, el medio ambiente y la seguridad en el trabajo sin ningún compromiso. Llame al 800-255-4255 y pida que lo comuniquen con Atención al cliente - soporte técnico.

Los representantes capacitados de la fábrica se encuentran en las ciudades continentales principales de los Estados Unidos. Llame a Atención al cliente al 800-255-4255 ó visite nuestro sitio Web en www.prosoco.com para conocer el nombre del representante de Consolideck® en su área.

Para la limpieza de mantenimiento, utilice Consolideck® lsKlean Super Concentrate. lsKlean Super Concentrate contiene silicato de litio para mejorar la densidad de la superficie y para conservar el brillo de la superficie de los pisos tratados con Consolideck®.

No utilice otros limpiadores, incluyendo los limpiadores comerciales o de uso doméstico, que puedan contener ingredientes ácidos o alcalinos que puedan quitar el brillo de los pisos tratados con Consolideck®.

Para restaurar el brillo máximo a las áreas de mucho tráfico, diluya lsGuard® con una parte de agua y repita los pasos 1 al 5 de las Instrucciones de aplicación en las áreas afectadas.

Si desea obtener recomendaciones sobre otros tratamientos de protección o revestimientos para superficies, comuníquese con el departamento de Atención al cliente llamando al 1-800-255-4255.

informaCiÓn De SeguriDaDConsolideck® lsGuard® es una solución ligeramente alcalina. Utilice el equipo de seguridad y los controles adecuados para el sitio de trabajo durante la aplicación y el manejo. Lea toda la etiqueta y la MSDS para conocer las instrucciones de precaución antes de utilizar el producto.

Primeros auxiliosContacto con los ojos: Retire los lentes de contacto. Enjuague inmediatamente los ojos durante 15 minutos con agua potable limpia manteniendo abiertos los párpados. Busque atención médica inmediatamente.

lsGuard®



pROdUcT daTa SheeT

RegulatoRy ComplianCeVOC ComplianceConsolideck® lsKlean Super Concentrate is compliant with all national, state and district VOC regulations.

lsKlean Super Concentratemaintenance cleaner for lithium-silicate hardened/densified concrete floors

Product Data Sheet • Page 1 of 4 • Item #46084 • CDLSKSC - 041510 • ©2010 PROSOCO • www.consolideck.com

oVeRVieWConsolideck® lsKlean Super Concentrate is a specially designed maintenance cleaner for concrete floors treated with lithium-silicate hardening/densifying products.

This specialized blend of degreasers and detergents removes most common soiling found on concrete floors. It is ideal for concrete floors everywhere, from warehouses and manufacturing plants to schools, stores, hospitals, restaurants and more.

lsKlean Super Concentrate has a lithium-silicate hardener/densifier to help maintain concrete hardness. During cleaning, the lithium-silicate hardens any “soft” calcium hydroxide left over from the original hardening-densifying treatment, or exposed by traffic or abrasion.

There is no better way to maintain Consolideck® LS® hardened/densified floors. Though lsKlean Super Concentrate is specifically made for LS floors, it is perfect for almost any concrete floor.

Regular maintenance cleaning with lsKlean Super Concentrate as part of a comprehensive maintenance program ensures the highest appearance and performance standards for all indoor concrete flatwork.

SpeCifiCationSFor all PROSOCO product specifications visit www.prosoco.com and click on “SpecBuilder” or “Solution Finder.“

aDVantageS• Maintains concrete floor hardness and shine.• Removes most common soiling.• Flexible dilution for both surface and deep

cleaning.• Readily biodegradable. Low toxicity. • Contains US EPA DfE (Designed for the

Environment) conformant CleanGredients® listed surfactants.

• Concentrated for economy of storage and transport.

• No rinsing needed for routine surface cleaning of floors.

• Available in convenient pre-measured 4-oz packages for easy dilution.

Limitations•May not remove some embedded stains.

03 00 00 Concrete03 01 30.51 Cleaning of Cast-In-Place Concrete

03 30 00 Cast-In-Place Concrete09 00 00 Finishes

09 01 60 Maintenance of Flooring

FORM clear blue liquid, fresh clean odor

SPECIFIC GRAVITY 1.014

pH 11.0

WT/GAL 8.45 lbs

ACTIVE CONTENT NA

TOTAL SOLIDS NA

VOC CONTENT < 1%

FLASH POINT >200°F (>93°C) ASTM D 3278

FREEZE POINT 30°F (--1°C)

SHELF LIFE 2 years in unopened, factory-sealed container

appliCationBefore use, read “Preparation” and “Safety Information.”

ALWAYS TEST for suitability, dilution rates and desired results before overall application. Test using the following application instructions. Let test area dry thoroughly before inspection.

DilutionFor normal cleaning

dilute 1 oz of cleaner per 1-gal fresh waterFor deep cleaning

dilute 2 oz of cleaner per 1-gal fresh waterPAX dilution

one 4-oz PAX per 5-gal fresh water

Application Instructions1. Apply with a mop or automatic scrubber. 2. For routine surface cleaning, rinsing the

concrete floor is not necessary. Mop up spent cleaner and dissolved contaminants, or vacuum up with automatic scrubber. After deep-cleaning, rinse well with fresh water. Do not let puddles or concentrated cleaner dry on the floor.

3. Buff the cleaned floor with a white pad to increase the shine.

CleanupClean tools and equipment using fresh water.


pRepaRationSweep or vacuum to remove loose materials from the surface to be cleaned.

Pre-clean oil spots or other deep stains with the appropriate Consolideck® product. For recommendations, call Customer Care toll-free at 800-255-4255.

Surface and Air TemperaturesCleaning effectiveness is reduced when surface and air temperatures fall below 50°F (10°C).

Do not apply at temperatures below 40°F (4°C).

EquipmentApply using a mop or automatic scrubber.

Storage and HandlingStore in a cool, dry place. Always seal container after dispensing. Do not alter or mix with other chemicals.

Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperatures of 45-100°F (7-38°C). Do not double stack pallets.

Dispose of unused product and container in accordance with local, state and federal regulations.

Safety infoRmationConsolideck® lsKlean Super Concentrate is a commercial strength concentrated cleaner and causes irritation. Field-diluted solution may cause eye and skin irritation. Use appropriate safety equipment and job site controls during application. Read full label and MSDS for precautionary instructions before use.

First AidIngestion: Do not induce vomiting. Get immediate medical assistance.

Eye Contact: Rinse thoroughly for 15 minutes. Get medical assistance.

Skin Contact: Rinse thoroughly. Get medical attention if irritation persists.

Inhalation: Remove to fresh air. Get medical attention as necessary.



lsKlean Super ConcentratepROdUcT daTa SheeT

BeST pRacTiceS


WaRRantyThe information and recommendations made are based on our own research and the research of others, and are believed to be accurate. However, no guarantee of their accuracy is made because we cannot cover every possible application of our products, nor anticipate every variation encountered in masonry surfaces, job conditions and methods used. The purchasers shall make their own tests to determine the suitability of such products for a particular purpose.

PROSOCO, Inc. warrants this product to be free from defects. Where permitted by law, PROSOCO makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness for particular purpose. The purchaser shall be responsible to make his own tests to determine the suitability of this product for his particular

purpose. PROSOCO’s liability shall be limited in all events to supplying sufficient product to re-treat the specific areas to which defective product has been applied. Acceptance and use of this product absolves PROSOCO from any other liability, from whatever source, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict liability. This warranty may not be modified or extended by representatives of PROSOCO, its distributors or dealers.

CuStomeR CaReFactory personnel are available for product, environment and job-safety assistance with no obligation. Call 800-255-4255 and ask for Customer Care - technical support.

Factory-trained representatives are established in principal cities throughout the continental United States. Call Customer Care at 800-255-4255, or visit our web site at www.prosoco.com, for the name of the Consolideck® representative in your area.

For spot cleaning heavily soiled areas, begin testing lsKlean Super Concentrate at a dilution of 2-ounces of cleaner to 1-gallon of fresh water.

Do not use dilutions stronger than 4-oz cleaner concentrate to 1-gallon of fresh water. Always use the mildest effective dilution possible.

To remove deeply embedded oil and grease stains, test Consolideck® Oil & Grease Stain Remover.

Use soft brushes/soft pads with auto scrubbers. Never use aggressive brushes or pads on polished concrete.

Use lsKlean Super Concentrate as part of a comprehensive maintenance program that includes daily cleaning with Consolideck® DailyKlean, and regular deep cleaning at least once a week.

Never go it alone. If you have problems or questions, contact your local PROSOCO distributor or field representative. Or call PROSOCO technical Customer Care, toll-free, at 800-255-4255.





pROdUcT daTa SheeT

REGULATORY COMPLIANCEVOC ComplianceConsolideck® PolishGuard is compliant with the following national, state and district AIM VOC regulations:

X US Environmental Protection Agency

X California Air Resources Board SCM Districts

X South Coast Air Quality Management District

X Maricopa County, AZ

X Northeast Ozone Transport Commission

PolishGuardglossy protective sealer for interior horizontal concrete

Product Data Sheet • Page 1 of 4 • Item #46063 • CDPG - 091010 • ©2010 PROSOCO • www.consolideck.com

OVERVIEWConsolideck® PolishGuard is a durable, chemical-resistant, high-gloss, protective coating that dramatically increases the stain resistance of interior concrete floors.

PolishGuard is ideal for steel-troweled, burnished, polished or decorative concrete and cement terrazzo floors that are exposed to accidental spills of food products, household cleaners and industrial solutions.

This chemical-resistant, non-yellowing formulation enhances the appearance of standard gray, integrally colored, dyed, stained or color-hardened concrete floors.

ADVANTAGES• Produces a long-lasting, tough protective

shine on any interior concrete flatwork.• Perfect for floors hardened/densified with

Consolideck® LS® and LS/CS®.• Adds depth and luster to colored

concrete, including surfaces decorated with Consolideck® GemTone Stain and ColorHard.

• Keeps soiling and contaminants from penetrating, making maintenance cleaning faster, more effective and more economical.

• Treated floors maintain slip resistance.• Low odor. Easy to apply. Fast drying.• UV stable. Will not yellow, discolor, peel or

flake.• VOC Compliant. Non-flammable. Non-toxic.

Water-based.

Limitations• Only for use on indoor horizontal concrete

surfaces.• Will not compensate for structural defects.

Surfaces must be clean and in good repair before application.

03 30 00 Cast-In-Place Concrete03 35 00 Concrete Finishing

09 60 00 Flooring09 61 00 Flooring Treatments

FORM Milky white liquid


pH 8.4

WT/GAL 8.50 lbs

ACTIVE CONTENT 15%

TOTAL SOLIDS 15%

VOC CONTENT 100 g/L maximum

FLASH POINT >200°F (>93°C)

FREEZE POINT 32°F (0°C)

SHELF LIFE 1 year in factory-sealed unopened container

Follow the appropriate cleaner with thorough water rinsing. If a d-limonene based cleaner/stripper is used, clean treated surfaces with Consolideck® Cleaner/Degreaser and rinse thoroughly.

Acid-stained concrete must be thoroughly neutralized and rinsed prior to application.

Application may begin as soon as prepared surfaces are dry.

Surface and Air TemperaturesTemperatures for application should be 40–100°F (4–38°C).

EquipmentApply with low pressure sprayer and a microfiber mop. Do not atomize.

Storage and HandlingStore in a cool, dry place. Always seal container after dispensing. Do not alter or mix with other chemicals. Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperatures of 40–100°F (4–38°C). Keep from freezing. Do not double stack pallets. Dispose of in accordance with local, state and federal regulations.

APPLICATIONBefore use, read “Preparation” and “Safety Information.”

ALWAYS TEST each surface for suitability and results before overall application. Use the following application instructions. Let surface dry thoroughly before inspection.

Dilution & MixingApply as packaged. Do not dilute or alter, or use other than as specified. Mix well before use.


PREPARATIONProtect people, vehicles, property, plants and all surfaces not set to receive PolishGuard from product, splash and wind drift. Use polyethylene or other proven protective material.

PolishGuard may be applied to existing, cured concrete of any age. Surfaces must be clean and structurally sound. Remove all foreign materials including bond breakers, curing agents, surface grease and oil, and construction debris using the appropriate Consolideck® surface prep cleaner listed below:

Consolideck® SafStrip • cure & seals • paint • high strength coatings

Consolideck® SafEtch®* • concrete laitance • construction soiling *Not for use on concrete previously treated with Consolideck® LS®, LS/CS® or lsGuard®.

Consolideck® Wax & Cure Remover • waxes, sealers & coatings • low-solids cure & seals

Consolideck® Cure & Seal Remover • high-solids cure & seals

Consolideck® Concrete Floor Restorer • general soiling • rust and other metallic staining • light wax coatings

Consolideck® PreKlean • laitance • residual surface salts

Consolideck® Cleaner/Degreaser • general soiling • grease and oil

Consolideck® Oil & Grease Stain Remover • deep-seated oil & grease staining

Typical Coverage RatesVariations in surface texture, concrete quality, porosity, job-site conditions, temperature and relative humidity affect coverage rates and drying times. Calculate coverage rate by testing a representative section of the finished concrete surface using the following instructions. The following figures are for estimating only.

Estimated Coverage Rates• 400–800 square feet per US gal• 10–20 square meters per Liter

Calculating Project-Specific Target Coverage Rate1. Prepare the test area using the information in

the “Preparation” section. Surfaces must be clean, dry and absorbent.

2. Add 1-gallon of PolishGuard to a clean, pump-up sprayer fitted with a 0.5 gpm conical or fan spray tip. Apply according to the following Application Instructions. Repeat as needed for the desired level of finish.

3. Measure the test area and the amount of PolishGuard applied to establish the Target Coverage Rate per gallon. Protect the completed test area from moisture for at least 4 hours.


PolishGuardpROdUcT daTa SheeT

BeST pRacTiceS


Application InstructionsPolishGuard may be applied to broomed, steel troweled, honed, polished or highly polished interior concrete surfaces. For best results, treat floors with Consolideck® LS® or LS/CS® before application.

1. Lightly wet a clean microfiber pad with PolishGuard, leaving the pad damp.

2. Spray-apply PolishGuard using a clean, pump-up sprayer fitted with a 0.5 gpm conical or fan spray tip. Work from one control joint to another.

3. Spread with the damp microfiber pad. Maintain a thin, even coating and wet edge. Stop spreading once drying begins. Do not overlap. Use two people – one spraying and one spreading – for best results.

4. Allow to dry tack free, typically 20-60 minutes.5. Repeat steps 1–4. Two coats are recommended

for maximum protection and shine.6. To increase gloss, use a high-speed burnisher

fitted with a Consolideck® HEAT Burnishing Pad. Burnish at a fast walking pace.

7. For maximum gloss, continue burnishing with a white polishing pad. Burnish at a fast walking pace.

Protect from water for 4 hours. At 72°F [22°C] and 40% relative humidity, product dry times are:

• To Touch: 30-–60 minutes• Light Foot Traffic: 4 hours• Normal traffic: overnightConsolideck® PolishGuard gains its full stain repellency properties in 7 days.

CleanupBefore the product dries, clean tools and equipment with fresh water. Immediately wash over spray off glass, aluminum, polished or other surfaces with fresh water.

MaintenanceSweep the floor daily with a microfiber pad or dry dust mop. When needed, dry buff with a high-speed burnisher and a white pad to refresh the gloss.

PolishGuard improves the resistance of concrete floors to staining. However, acidic substances, including foods, may etch and stain. Clean ALL spills as quickly as possible.

Use Consolideck® lsKlean Super Concentrate or Consolideck® DailyKlean for maintenance cleaning. lsKlean Super Concentrate contains lithium-silicate for improving surface density and preserving the surface sheen of Consolideck® floors. Do not use other cleaners, including off-the-shelf and common household cleaners, which may contain acidic or alkaline ingredients that can dull the finish of Consolideck® floors.

To restore maximum shine to high traffic areas, repeat Application Instructions steps 1–7 in affected areas.

Only apply PolishGuard to clean, dry and absorbent concrete. Confirm absorbency with a light water spray – surfaces to be treated should wet uniformly.

Thoroughly neutralize and rinse acid-stained concrete before applying PolishGuard.

For best results, harden/densify floors with Consolideck® LS® or LS/CS® before applying PolishGuard.

For best durability and stain resistance, burnish freshly applied PolishGuard with a high-speed burnisher using a Consolideck® HEAT Burnishing Pad or equivalent polishing pad for high-gloss finishes. Follow by burnishing with a white polishing pad.

Always use Consolideck® lsKlean Super Concentrate or Consolideck® DailyKlean for maintenance cleaning of concrete floors. Conventional floor cleaners may dull high-gloss finishes. Consolideck® lsKlean Super Concentrate and Consolideck® DailyKlean contain no harsh acids, alkalines, solvents or abrasives.

Never go it alone. If you have problems or questions, contact your local PROSOCO distributor or field representative. Or call PROSOCO technical Customer Care, toll-free, at 800-255-4255.



WARRANTYThe information and recommendations made are based on our own research and the research of others, and are believed to be accurate. However, no guarantee of their accuracy is made because we cannot cover every possible application of our products, nor anticipate every variation encountered in masonry surfaces, job conditions and methods used. The purchasers shall make their own tests to determine the suitability of such products for a particular purpose.

PROSOCO, Inc. warrants this product to be free from defects. Where permitted by law, PROSOCO makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness for particular purpose. The purchaser shall be responsible to make his own tests to determine the suitability of this product for his particular purpose. PROSOCO’s liability shall be limited in all events to supplying sufficient product to re-treat the specific areas to which defective product has been applied. Acceptance and use of this product

absolves PROSOCO from any other liability, from whatever source, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict liability. This warranty may not be modified or extended by representatives of PROSOCO, its distributors or dealers.

CUSTOMER CAREFactory personnel are available for product, environment and job-safety assistance with no obligation. Call 800-255-4255 and ask for Customer Care – technical support.


SAFETY INFORMATIONConsolideck® PolishGuard is an alkaline solution. Use appropriate safety equipment and job site controls during application and handling. Read full label and MSDS for precautionary instructions before use.

First AidEye Contact: Remove contact lenses. Immediately flush eyes for 15 minutes in clear running water while holding eyelids open. Seek medical attention immediately.

Skin Contact: Wash contacted area with soap and water. DO NOT attempt to neutralize with chemical agents. If irritation persists, seek medical attention.

Ingestion: Drink large quantities of water or milk. DO NOT induce vomiting. Seek medical attention immediately.

Inhalation: Remove affected person to fresh air. Wash mouth and nasal passages with water repeatedly. If breathing difficulties persist, seek medical attention.




RegulatoRy ComplianCeVOC ComplianceConsolideck® SafEtch® is compliant with the following national, state and district AIM VOC regulations

SafEtch®non-fuming cleaner and surface-prep for concrete

Product Data Sheet • Page 1 of 3 • Item #46010 • CDSE - 042009 • ©2009 PROSOCO • www.prosoco.com

oVeRVieWConsolideck® SafEtch® is an effective, safe alternative to traditional acidic compounds for cleaning and preparing horizontal concrete for densifying and hardening.

SafEtch® rids concrete of embedded oil, grease, efflorescence and dirt. The cleaner also dissolves a small amount of surface cement, while leaving the aggregate untouched. That mild “etch” creates greater surface area, for more complete penetration and effectiveness of the hardener/densifier -- or any other protective treatment. It’s ideal for projects where traditional acidic cleaners are not allowed.

Non-fuming SafEtch® contains no hydrochloric or other traditional inorganic acids and is safe for use on and around most metal surfaces. Additionally, it is up to 70 percent more effective than citric and glycolic acids, and 50 percent more effective than phosphoric acid.

SpeCifiCationSFor all PROSOCO product specifications visit www.prosoco.com and click on “SpecBuilder” or “Solution Finder.“

aDVantageS•Proven effective for removing common

construction soiling.•Replaces traditional mineral and organic

acid products.•Low odor and water-rinsable.•Non-fuming and environmentally

responsible.•Will not harm most cleaning equipment or

metal surfaces.•Safe for interior cleaning.

Limitations•Not suitable for polished/unpolished marble,

limestone or travertine.•May cause discoloration and corrosion on

certain types of metals. ALWAYS TEST.

pROdUcT daTa SheeT03 00 00 Concrete03 01 30.51 Cleaning of Cast-In-Place Concrete03 01 50.51 Cleaning Cast Decks and Underlayment

09 00 00 Finishes09 01 60.91 Flooring Restoration

FORM clear purple liquid


pH <1.0 @ 1:3 dilution

WT/GAL 9.24 lbs

ACTIVE CONTENT NA

TOTAL SOLIDS NA

VOC CONTENT NA

FLASH POINT >200°F (>93°C)

FREEZE POINT –22°F (–30°C)

SHELF LIFE 3 years in unopened, factory-sealed container

Storage and HandlingStore in a cool, dry place with adequate ventilation. Always seal container after dispensing. Do not alter or mix with other chemicals.

Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperature of 45-100°F (7-38°C). Do not double stack pallets. Dispose of unused product and container in accordance with local, state and federal regulations.

appliCationBefore use, read “Preparation” and “Safety Information.”

ALWAYS TEST (minimum 4 ft x 4 ft area) for dilution rates, surface compatibility and desired results. Test each surface and each type of soiling using the following application instructions. Let test dry thoroughly before inspection.

Dilution & Coverage RatesSafEtch® may be diluted with up to three parts clean water, depending on the nature and severity of soiling. Always pour water into empty bucket first, then carefully add concentrate.

Coverage rates vary based upon severity of soiling, surface texture and porosity. Always test to ensure desired results. The following is provided for estimating purposes only:

• 125–500 sq.ft. (12–46 sq.m.) per gallon of cleaner concentrate

Application InstructionsExterior1. Use clean water to thoroughly prewet surface

to be cleaned.


pRepaRationProtect people, vehicles, property and all surfaces not set for cleaning from product, splash, wind drift, residue and rinse water.

When possible, finish cleaning before installing windows, doors, light fixtures, hardware, surrounding metal and other items that may be damaged by cleaning. If already in place, protect. Extended contact with the cleaning solution or its vapors may result in discoloration or damage. All caulking and sealant materials should be in place and thoroughly cured before cleaning.

Surface and Air TemperaturesTo avoid harm to masonry, do not clean when temperatures are below freezing or will be overnight. Best results are obtained when air and masonry surface temperatures are 40°F (4°C) or above. If freezing conditions exist prior to application, let the masonry to thaw.

EquipmentApply using low-pressure sprayer (50 psi max), roller or masonry washing brush. Do not use high pressure spray.

Rinse with enough water and pressure to flush spent cleaner and dissolved soiling from the masonry surface and surface pores without damage. Inadequate rinsing leaves residues which may stain the cleaned surface.

Masonry-washing equipment generating 400-1000 psi with a water flow rate of 6-8 gpm is the best water/pressure combination for rinsing porous masonry. Use a 15-45° fan spray tip. Heated water (150-180°F; 65-82°C) may improve cleaning efficiency. Use adjustable equipment for reducing water flow rates and rinsing pressure as needed for sensitive surfaces.

Rinsing pressures above 1000 psi and fan spray tips smaller than 15° may permanently damage sensitive masonry. Flow rates under 6 gpm may reduce cleaning productivity and contribute to uneven cleaning results.

2. Apply liberally using low pressure spray (50 psi max), roller or densely filled (tampico) masonry washing brush. Do not apply with high pressure spray. Do not atomize.

3. Let the cleaning solution dwell 3-5 minutes. Reapply. Light scrubbing of the surface improves cleaning results especially where high pressure rinsing equipment is not available. Do not let cleaning solution “dry into” the concrete. If solution starts to dry, reapply.

4. Rinse with clean water, covering each section of the surface with a concentrated stream of water.

InteriorProper ventilation is necessary. Follow exterior application procedures. If pressure-rinsing is not possible, use a sponge or soft-fibered brush to rinse thoroughly with clean water.

CleanupClean tools and equipment with fresh water.


SafEtch®

pROdUcT daTa SheeT


Safety infoRmationConsolideck® SafEtch® is an acidic cleaning product with safety issues common to corrosive materials. Use appropriate safety equipment and job site controls during application and handling. Read the full label and MSDS for precautionary instructions before use.

First AidIngestion: Do not induce vomiting. If conscious, give 3-4 glasses of water and seek immediate medical attention.

Eye Contact: Rinse eyes thoroughly for 15 minutes while lifting eyelids to assure thorough cleaning. Get immediate medical assistance.

Skin Contact: Remove contaminated clothing and rinse thoroughly for 15 minutes. Get medical attention if persistent irritation develops. Launder contaminated clothing before reuse.

Inhalation: Remove to fresh air. Give artificial respiration if not breathing. Get immediate medical attention.

24 Hour Emergency Information: INFOTRAC at 800-535-5053

WaRRantyThe information and recommendations made are based on our own research and the research of others, and are believed to be accurate. However, no guarantee of their accuracy is made because we cannot cover every possible application of our products, nor anticipate every variation encountered in masonry surfaces, job conditions and methods used. The purchasers shall make their own tests to determine the suitability of such products for a particular purpose.

PROSOCO, Inc. warrants this product to be free from defects. Where permitted by law, PROSOCO makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness for particular purpose. The purchaser shall be responsible to make his own tests to determine the suitability of this product for his particular purpose. PROSOCO’s liability shall be limited in all events to supplying sufficient product to re-treat the specific areas to which defective product has been applied. Acceptance and use of this product absolves PROSOCO from any other liability, from whatever source, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict liability. This warranty may not be modified or extended by representatives of PROSOCO, its distributors or dealers.

CuStomeR CaReFactory personnel are available for product, environment and job-safety assistance with no obligation. Call 800-255-4255 and ask for Customer Care - technical support.


BeST pRacTiceSAlways apply to surfaces thoroughly pre-wet with fresh water.

It is extremely important to thoroughly rinse off spent cleaner and dissolved contaminants with lots of fresh water. This ensures there are no residues left that could interfere with the penetration of hardener/densifiers.

Never go it alone. For problems or questions, contact your local PROSOCO distributor or field representative. Or call PROSOCO technical Customer Care toll-free at 800-255-4255.

SafEtch®

pROdUcT daTa SheeT

Consolideck Spill Kit

Description & Use

Spills of water- and oil-based products on finished concrete floors -- even floors with protective treatments -- can leave ugly stains if notremoved promptly and correctly. The Consolideck Quick Response Spill Kit has everything needed for containing and removing harmfulcontaminants. A Quick Response Spill Clean-up Kit stationed in an area prone to spills is can mean the difference between a routineclean-up and a costly re-finishing job.

Items Included

Oil & Grease Stain Remover (32 oz.)Multipurpose Absorbent Shop Towels (1 Roll)SpillGuard Neutralizing Absorbent (2 lbs.)SpillGuard S Petroleum Absorbent (4 lbs.)ScraperBroom and DustpanScrub BrushDisposable GlovesWaste Bags (roll)Collapsible Warning SignProduct Data & MSDSWall-poster instructionsInstruction card

Consolideck

Spill Kit(psc-solutions.com)

Consolideck Kits®

®

®

®

Consolideck® High Performance Concrete http://www.consolideck.com/SpillKit.aspx

1 de 1 6/9/2011 8:05 PM

Documents

dalyi Klean - northwest.com.mx fileTypical Technical daTa pROdUcT daTa SheeT REGULATORY COMPLIANCE Consolideck® DailyKlean is compliant with all national, state and district VOC regulations