DAGR Receiver Default Settings

GPS Setup Page• Page Function• Page Fields

– Operating Mode– Power-On Operating Mode– Frequency– SV Code– Elevation Hold– Receiver Autonomous Integrity Monitor (RAIM) Mode and Status– Rehearsal Route and Ground Speed– Anti-Jam Accessory Mode and Status– Differential Global Position System (DGPS) Mode and Status

(Advanced)– Wide Area GPS Enhancements (WAGE) Mode and Status

(Advanced)– Mask Mode and Angle (Advanced)– SV Hold (Advanced)

GPS Setup Page

1 From the GPS Setup page, push the ENTER key to highlight a field.

2. Use the cursor control keys to highlight the desired field, then perform one of the following:

(a) To edit field text or numeric content, push the ENTER key. For some fields, field content is chosen from a list and pushing the ENTER key displays the list editor.

GPS Setup Page

• Operating Mode Field– Continuous

– Fix

– Average

– Time Only

– Standby

– Rehearsal

– Test

– Off

• Power-On Operating Mode Field– Default– Continuous – Standby– Fix – Average– Time Only– Frequency Field

Selections• L1 Primary • L2 Primary• L1 Only

GPS Setup Page

• Frequency Field Default– L1 Primary

– L2 Primary

– L1 Only

GPS Setup Page

• SV Code Field– All-Y

– Mixed

• Note– Mixed Susceptible to

spoofing signals

GPS Setup Page

GPS Setup Page

• Elevation Hold Field– Automatic

– Manual

GPS Setup Page

• RAIM Mode Field• RAIM Status Field

– Unavailable

– No Faults

– Faults Found

GPS Setup Page

• Rehearsal Route Field• Rehearsal Ground

Speed Field

• Anti-Jam Mode Field• Anti-Jam Accessory

Status Field– Not Connected

– Off

– Pass Through (Normal)

– Nulling

– Test In Progress

– Self-Test Failed

GPS Setup Page

• Mask Mode Field (Advanced)

• Mask Angle Field (Advanced)

GPS Setup Page

• DGPS Mode Field (Advanced)

• DGPS Status Field (Advanced)– Unavailable

– Receiving

– Using

GPS Setup Page

• Wage Mode Field (Advanced)

• Wage Status Field (Advanced)

GPS Setup Page

• SV Hold (Advanced)

To access the field menu list, push the MENU key. Scroll to the desired menu item (e.g., Edit Field), then push the ENTER key.

GPS Setup Page

GPS Setup Page

(3) For list editors, scroll to the desired field content, then push the ENTER key.

(4) Display returns to the GPS Setup page with change made to

field content.

CHECK ON LEARNING

• Name 3 of the DAGR operating modes.– Continuous, fix, average, time

delay, average, stand-by, rehearsal, test, and off.

• What are the two SV-Code fields? – All-Y and mixed

a. Enable Auto-Off Function •NOTE

– Auto-Off Mode

(1) From the Power Saver page, highlight the Auto-Off Mode field. Push the ENTER key.

- Auto-off Mode Field

Power Saver Page

(2) Highlight On, then push the ENTER key. The display returns to the Power Saver page with the Auto-Off Mode field highlighted including changes made.

(3) From the Power Saver page, highlight the Auto-Off Timer field. Push the ENTER key.

- Auto-Off Timer Field

Power Saver Page

Power Saver Page

(4) Enter the desired time value (15 seconds up to 30 minutes), then push the ENTER key. The display returns to the Power Saver page with the Auto-Off Timer field highlighted including changes made

Power Saver Page

b.Enable Auto-Standby Function

• NOTE

– Auto-Standby Mode

(1) From the Power Saver page, highlight the Auto-Standby Mode field. Push the ENTER key.

- Auto-Standby Field

Power Saver Page

(2) Highlight On, then push the ENTER key. The display returns to the Power Saver page with the Auto-Standby Mode field highlighted including changes made.

(3) From the Power Saver page, highlight the Auto-Standby Timer field. Push the ENTER key.

- Auto-Standby Timer Field

Note

- Set Battery Page to enable auto-standby

Power Saver Page

(4) Enter the desired time value (5 minutes up to 9 hours), then push the ENTER key. The display returns to the Power Saver page with the Auto-Standby Timer field highlighted including changes made.

Power Saver Page

Enable/Disable Off Mode Display Heater

(1) From the Power Saver page, highlight the Off Mode Display Heater field. Push the ENTER key.

- Off Mode Display Heater Field

Power Saver Page

Note - Off Mode Display

heater has no effect on operation

(2) Highlight Enabled or Disabled, then push the ENTER key. The display returns to the Power Saver page with the Off Mode Display Heater field highlighted including changes made.

Power Saver Page

CHECK ON LEARNING

• What is the desired time range for the auto-off timer field?– 15 seconds to 30 minutes

• What is the desired time range for the auto-standby timer field?– 5 minutes to 9 hours

Disable Auto-On Function(1) From the Auto-On page,

highlight Mode field, then push the ENTER key

Note

- Must be Off for other fields can be configured.

- Mode Field

Auto-On Page

(2) Highlight Off, then push the ENTER key.

(3) Display returns to the Auto-On page with the Mode field highlighted and changes made.

Auto-On Page

Select Time Zone (1) From the Auto-On page,

highlight the Start Time and Date or Stop Time and Date fields. Push the MENU key.

(2) Highlight Select Time Zone, then push the ENTER key.

(3) Highlight the desired time zone, then push the ENTER key. Returns to the Auto-On page with the time zone reference changed.

Auto-On Page

Auto-On Page

Set Start of Auto-On FunctionNote - Two Options

(1) Start auto-on when mode is switched from off. (a) From the auto-on page (with or without a field highlighted), push the MENU key.

Auto-On Page

(b) Highlight Start When enable, then push the ENTER key.

(c) The auto-on page displays the Start Time and Date filed with Start When Enabled.

- Start Time and Date Field

Auto-On Page

(2) Start Auto-On at specific time and date (a) From the Auto-On page, highlight the Start Time and Date field, or highlight the Start Time field. Push the ENTER key.

(b) Enter desired start time, then push the ENTER key.

Auto-On Page

(c) Highlight the Start Date field, then push the ENTER key.

(d) Enter desired start date, then push the ENTER key.

(e) The Auto-On page Start Time and Start Date fields display entered data.

Auto-On Page

Set Stop of Auto-On FunctionNote - Two Options

(1) Stop auto-on when mode switched to Off. (a) From the auto-on page (with or without a field highlighted), push the MENU key.

(b) Highlight Stop When Disable, then push the ENTER key.

(c) The auto-on page displays the Stop Time and Date filed with Stop When Disabled.

- Stop Time and Date Field

Auto-On Page

Auto-On Page

(2) Stop Auto-On at specific time and date (a) From the Auto-On page, highlight the Stop Time and Date field, or highlight the Stop Time field. Push the ENTER key.

(b) Enter desired stop time, then push the ENTER key.

Auto-On Page

(c) Highlight the Stop Date field, then push the ENTER key.

(d) Enter desired stop date, then push the ENTER key.

(e) The Auto-On page Stop Time and Start Date fields display entered data.

Set Time interval Between Auto-On Functions

(1) From the Auto-On page, highlight the Time Interval field. Push the ENTER key.

- Time Interval Field

Auto-On Page

(2) Enter desired time interval, then push the ENTER key.

(3) The Auto-On page Time Interval field displays entered data.

Auto-On Page

Enable Auto-On Function

(1) From the Auto-On page, highlight the Mode field. Push the ENTER key.

(2) Highlight desired mode of operation (Manual or Automatic), then push the ENTER key.

Auto-On Page

(3) Auto-On function is now enabled and will start and continue operating as previously set up until disabled. After auto-on is enabled, only the Mode field content can be changed.

Auto-On Page

CHECK ON LEARNING

• What is the format for the stop date field data?– DD-MM-YYYY

Set Units Page

(1) From the Units page, push the ENTER key to highlight a field. Push the ENTER key again for edit capabilities of the field.

Units Page

- Coord/Grid Field

- Resolution Field

Units Page

- Datum/Ellipsoid Field

- Datum ID Field

Units Page

- Position Error Field

- Elevation Field

Units Page

- Reference Field

- Range Field

Units Page

- Speed Field

- Time Zone Field

Units Page

- Angle Field

- North Reference Field

Units Page

- MAGVAR Source Field

- MAGVAR Units Field

Units Page

- Entered MAGVAR Value Field

Units Page

(2) Revise the selected field with appropriate information, then push the ENTER key to save changes to that field.

(3) Use the cursor control keys and the ENTER key in a similar manner to individually revise all of the remaining fields as required

Units Page

CHECK ON LEARNING

• What is a datum?– A representation of the surface of

the earth.

• What are the selections of the speed field?– Metric (kph), English (mph),

Nautical (kts)

• Page Function– CAUTION

• Enable and Orient Internal Compass

– Note• Cannot Compute Track

and Ground Speed

– Determine Track when receiver is moving slow

Internal Compass

• Orient the Internal Compass– Held Horizontally

Level

– Reorient compass at 50%, 25% battery life and after replacing primary batteries.

Internal Compass

Internal Compass

REF Para 10.3.3 a

Enable Internal Compass

(1) From the Internal

Compass page, highlight the Mode field, then set to Enabled.

- Mode Field

Internal Compass

(2) Set the speed value for the Stop Using Above This Speed field. Select appropriate speed units of measure if required.

- Stop Using When Above This Speed Field

Internal Compass

(3) Set the time value for the Start Using When Below Speed For field.

- Stop Using When Below Speed For Field

(4) The DAGR activates the internal compass as required without further operator action.

Internal Compass

REF Para 10.3.3 b

Orient Internal Compass

(1)Place the DAGR, face up, on a flat level surface.

(2) From the Internal Compass page (with or without fields highlighted), push the MENU key.

Internal Compass

(3) Highlight Calibrate, then push the ENTER key. The Internal Compass Calibration message is displayed.

(4) Slowly rotate the DAGR clockwise until the DAGR indicates calibration is complete. The display advises the operator to maintain or alter current rotation speed. Push the QUIT key to cancel the orientation.

Internal Compass

(5) Upon completion of the orientation, DAGR notifies the operator and requests acknowledgement. Push the ENTER key to acknowledge or allow it to time out and return to the Internal Compass page.

- Last Calibrated Field

1. From the Light/Contrast page,

highlight the Light Mode field,

then push the ENTER key.

2. Select either On or Off, then push the ENTER key. Display returns to the Light/Contrast page with change made.

Light/Contrast Page

Adjust Keypad/Display Lighting Level, Brightness Key Method

(1) From any display, push and hold the BRIGHTNESS key (illuminated bulb icon) and simultaneously push and hold the respective up or down cursor control key.

(2) Keypad/display lighting level adjusts up or down depending on which cursor control key is pushed.

Light/Contrast Page

1. From the Light/Contrast page, and no fields selected, push the respective up or down cursor control key .

2. The Display Lighting field percentage value and slider control adjust by one percent for each push of the up or down cursor control key. For larger adjustments, push and hold the up or down cursor control key.

- Display Lighting Field

Light/Contrast Page

Adjust Display Contrast Level

(1) From the Light/Contrast page,

and no fields selected, push the

respective left or right cursor

control key .

Light/Contrast Page

Light/Contrast Page

(2). The Contrast field percentage value and slider control adjust by one percent for each push of the left or right cursor control key. For larger adjustments, push and hold the left or right cursor control key. - Contrast Field

Note - Can adjust levels by editing the Display lighting Value.

CHECK ON LEARNING

• What must you avoid when using the internal compass on the DAGR so as not to get an erroneous reading? – Avoid large metal objects, strong

magnetic fields, or other electromagnetic interference.

• When calibrating the internal compass which way do you rotate the DAGR?– Clockwise