D a B E & S · 2014-09-10 · Gallon Home Brew Keg Sixth Barrel Quarter Barrel Slim Quarter Barrel Half Barrel T

Draft Beer Equipment & Supplies

‘14

www.wholesalebeerparts.com

Table of Contents

800.821.0114 (sales)585.546.6706 (local)585.546.4452 (fax)

Terms & Conditions 1Draft Towers 2-18Tower Parts 19-21Drip Trays 22-27Couplers 28-31Shanks 32Faucets 33-36Regulators 37-40Air Distributor Bars 41Tubing 42-43Fittings 44-47Clamps 48Wall Panels 49-50Foam on Beer Detectors (F.O.B) 51Gas Blender Panels & Accessories 52-53Gas Tanks 54Trunk Lines 55Glycol Power Packs 56-57Glycol System Components 58Air Shaft System Components 59-60Picnic Pumps 60-62Coil Box Coolers 63Cold Plate Coolers 64-65Conversion Kits 66-68Commercial Refrigeration Units 69-74Keg Storage 75Home Brew Equipment 76Soda & Wine Equipment 77Cleaning Equipment 78-81Cleaning Chemical 82-83Hand Carts 84-85Installation & Maintenance Tools 86Repair Kits & Keg Master List 87Index 88

5 Gallon HomeBrew Keg

Sixth Barrel Quarter Barrel Slim QuarterBarrel

Half Barrel

Type Also Known As Gallons Ounces 16 oz. Beers 12 oz. Beers Height Diameter Weight (Full)

5 Gal. Home Brew Keg Corny Keg 5 640 40 53 23" 9" 49 lbs.

Sixth Barrel Sixtel 5.16 661 41 55 23-3/8" 9-1/4" 58 lbs.

Quarter Barrel Pony Keg 7.75 992 62 82 13-7/8" 16-1/8” 87 lbs.

Slim Quarter Barrel Slim Pony Keg 7.75 992 62 82 23-3/8" 11-1/8" 87 lbs.

Half Barrel Full Size Keg 15.5 1984 124 165 23-3/8" 16-1/8” 161 lbs.

Note: Dimensions and weights may vary slightly depending on keg manufacturer. To be used only as a reference.

Front cover photo taken at ORBS Restaurant & Bar

758 South Avenue Rochester, NY 14620

Nick St. CroixDraft Beer Equipment [email protected]

Sean DohertyDraft Beer Equipment [email protected]

Alex ClarkDraft Beer Equipment [email protected]

Left to Right: Nick St. Croix, Sean Doherty, Alex Clark

Rochester Store Fixture Beer Department Staff

www.wholesalebeerparts.comPowered by Rochester Store Fixture

Rochester Store Fixture Co.707 North Street, Rochester, NY, 14605

800.821.0114 | 585.546.6706Fax 585.546.4452

1

Terms & Conditions

Speak with one of our Draft Beer Equipment representatives to place an order during regular business hours.

Order by Phone

1.800.821.0114 (Toll-Free) 585.546.6706 (Local)

Rochester Store Fixture’s new website makes ordering fast and easy! Order 24 hours a day, 7 days a week.

Order Online

www.wholesalebeerparts.com

Hours: Monday through Friday

8:30 AM to 5:00 PM EST

Ordering:

- Phone orders at 1-800-821-0114 or 585-546-6706 can be

placed during regular business hours.

- On-Line orders at www.wholesalebeerparts.com can be

placed 24 hours a day, 365 days a year.

Terms: We accept the following credit cards: Visa and Mastercard. Orders

may be shipped C.O.D, but will be subject to a non-refundable service fee

by UPS. Orders paid by check may be held by RSF until the funds clear.

Customers on terms must pay all outstanding balances within 30 days. Bal-

ances outstanding The customers net cost is shown for every item in this

catalog. Customer pays shipping charges from point of shipment. Manufac-

turers and RSF reserve the right to improve their products and change spec-

ifications without notice. All prices subject to change without notice.

Minimum Billing: Minimum invoice amount is $15.00. Orders not reaching

the minimum amount are subject to a $10.00 service charge, which will be

added to the invoice.

Warranties: All merchandise shown is offered free of defects in materials

and workmanship. Manufacturer warranties are listed where applicable.

There are no warranties, expressed or implied, by RSF, and no oral repre-

sentation shall serve to modify the terms of sale. RSF however, willl make a

good faith effort to work with the customer and the manufacturer in the event

that the product sold proves to be defective within the manufacturer’s war-

ranty period if in fact the part(s) or equipment have a manufacturer’s war-

ranty.

Product Suitability: Before ordering any equipment, check measurements

and specifications carefully, particular on draft beer towers, drip trays, bar

mobiles, back bar coolers and direct draw coolers to enure the equipment

will fit adequately. It is the responsibility of the customer to be sure equip-

ment will pass through doorways, go around corners, navigate stairways,

have proper ventialation where necessary, etc. Customer assumes sole re-

sponsibility for this. RSF is in no way responsible or liable should equipment

fail to fit through any of the scenarios described above. RSF is also not li-

able for incorrect or inadequate installation or assembly. It is the responsibil-

ity of the customer to follow any and all assembly instruction or installation

diagrams set forth by the manufacturer. Before purchase and use of any

equipment, please review the product application as well as state and local

codes and regulations to be sure that the product, installation and use will

comply.

Returns: RSF approval is required before any returns are to be made. Beer

parts made from RSF stock may be returned or exchanged for full value

within 10 business days from the time of receipt. The customer will be re-

sponsible for all shipping charges via UPS or freight carrier unless it is de-

termined that RSF or any of its vendors are at fault. Beer parts returns are

subject to a 20% restocking fee for returns made outside of the 10 busi-

ness day parameter. Custom parts, used parts, special orders or clearance

parts may not be returned. All sales on these items are final. No excep-

tions.

Missing Items: Any missing or incorrect items from a customers order

must be brought to the attention of RSF within 10 business days from re-

ceiving the order and action shall be determined by RSF. After 10 business

days, claims for missing or incorrect items will no longer be the responsibil-

ity of RSF and replacement of any missing or incorrect items will not be

made. No exceptions.

Equipment: The return of refrigeration units such as back bar coolers, direct

draw coolers or glycol power packs are subject to the prior approval and re-

turned goods policy of the manufacturer. All items must be shipped prepaid,

within 30 days from date of shipment, in original packing, and are subject to

inspection before a credit will be issued. Unauthorized returns will not be

credited. Replacement items will be charged to the customer if defective

items are not returned.

Shipping: Most items in this catalog are shipped from our stock in

Rochester, NY. If items requested by a customer are not in RSF stock at the

time the order is placed, RSF will have the item(s) drop shipped direct from

the manufacturer to the customer. RSF may drop ship items without consult-

ing the customer as long as it is ensured by RSF that the item(s) ordered will

arrive by any set forth deadlines expressed by the customer.

UPS: Most items ship via UPS Ground as long as items do not exceed UPS

weight and size limits. Shipping, handling and insurance charges will be

added to the customer’s invoice. There is an additional fee charged by UPS

for COD shipments. Payment for COD must be made by certified check or

money order and RSF reserves the right to hold orders until payment has

been received in full. Expedited shipping methods are available upon request

at an additional charge. RSF will always try to meet customer deadlines for

any orders placed within a reasonable amount of time, however, RSF is not

liable for failing to meet deadlines due to shipping issues such as inclement

weather delays, damaged items, accidents, etc.

Freight: Items too large to be shipped via UPS will be shipped by a freight

company. RSF will provide the customer with an estimate of freight charges.

All freight shipping and handling charges will be prepaid and added to cus-

tomer’s invoice or shipped freight collect. All freight quotes are based upon

commercial to commercial delivery without the need of a liftgate service. Cus-

tomers requiring this service must communicate this with RSF prior to ar-

ranging shipping services and the customer will be responsible for payment.

Any services added after the fact will be billed to the customer. No excep-

tions.

UPS/Freight Damage: The customer is responsible for inspecting and un-

loading shipments. When carrier accepts merchandise he assumes respon-

sibility for a safe delivery. Do not sign for shipments until you are satisfied

that there is no apparent damage or shortage. Any problems must be noted

on the shipping receipt with the driver and reported to Rochester Store Fix-

ture immediately. Save all shipping materials from any damaged shipments.

If there is concealed damage, notify the shipper within five days and request

an inspection. All freight claims are the customer’s responsibility.

2

Draft Beer Towers: Pass-Thru

Metropolis “H” & “M”

Part Number Taps Finish Glycol

808-MET8HSS 8 Stainless Steel $1,395.00





808-MET16MSS* 16 Stainless Steel $2,495.00







Glycol ready

3” Faucet centers (dimensions may vary)

16” Height to top of column; 15” Height to top of

crossbar

4” Diameter columns

3” Cylindrical crossbar

Comes standard with American style faucets

Complete specifications available upon request

Faucet handles not included

*Metropolis “M” has a third 4” diameter pedestal

positioned at the center of the tower evenly

splitting the number of taps to each side.

Tubular Pass-Thru


806-EXBR8SS 8 Stainless Steel $1,450.00




EX Bridge “U”Glycol Ready


4-1/8” Tower diameter

3/8” I.D Copper coolant line

3/16” I.D vinyl beer lines




Glycol Ready or Air Shaft


4” Tower diameter

Removable shank access panel underneath

cross bar


Other tap configurations available. Call for

pricing and lead time.

Complete specifications available upon

request


Copyright Rochester Store Fixture Inc. All rights reserved

Part Number Taps Finish Glycol Air

808-PTU6SS 6 Stainless Steel $1,395.00 $1,365.00




808-PTU14SS 14 Stainless Steel $1,995.00 N/A






3




3” Diameter brushed chrome columns

4” high by 5” wide “Air Tight” Stainless Steel box

with removeable lid


Comes standard with American style shanks and

faucets. Faucet handles not included.


Add $21.00 per line for stainless steel faucets and

shanks

3” Column Pass-Thru





with removeable lid






shanks

4” Column Pass-Thru


806-AC191-6SS 6 Stainless Steel $895.00

806-AC228-8SS 8 Stainless Steel $1,095.00




Arcadia Brewery Style “U”Glycol Ready

18-1/2” Standard height, 3” faucet centers, 4-1/2” Diameter

base flange, 3-3/8” Diameter columns

Available in Short version for all configurations:

14-1/2” Height and 3” faucet centers

Available in Wide version for 6,8,10 &12 tap configurations:

18-1/2” Height and 4-15/16” faucet centers

Available with PVD Gold or Black finish as a custom order.

Please allow 3-4 weeks. Call for pricing.

Come standard with American style faucets and screw-in

shanks. Faucet handles not included.

Other tap configurations available. Also available with 4”

diameter columns. Call for pricing.



817-PTSCR-6 6 Stainless Steel $640.00 $540.00



817-PTSCR-12 12 Stainless Steel $1,075.00 $810.00


817-LCPTB8SS 8 Stainless Steel $850.00 $720.00

817-LCPTB10SS 10 Stainless Steel $959.00 $820.00

817-LCPTB12SS 12 Stainless Steel $1,100.00 $885.00

817-LCPTB14SS 14 Stainless Steel $1,275.00 $1,025.00





4Copyright Rochester Store Fixture Inc. All rights reserved



810-BT8BSS 8 Stainless $905.00

810-BT8BPC 8 Chrome $975.00

810-BT8BTF 8 TF Brass $1,085.00

810-BT10BSS 10 Stainless $1,210.00

810-BT10BPC 10 Chrome $1,330.00

810-BT10BTF 10 TF Brass $1,410.00


810-BT12BPC 12 Chrome $1,370.00

810-BT12BTF 12 TF Brass $1,510.00


810-BT16BPC 16 Chrome $1,920.00

810-BT16BTF 16 TF Brass $2,130.00


810-BT20BPC 20 Chrome $1,975.00

810-BT20BTF 20 TF Brass $2,195.00

Glycol Ready

12-15/16” standard height

Optional “extra high” models:

2-5/8” addition (add suffix “-2”)


Please call for pricing and availability

4-5/8” square columns


Balancing restrictors included

FAUCETS NOT INCLUDED. See page 33-34 for faucet op-

tions.



Available in a dual sided configuration with 16,20,24,32,

and 36 taps. Call for pricing and specifications.

4-5/8” Column Bridge “T”

Glycol Ready


6-1/16” standard width

4-1/16” column width



FAUCETS NOT INCLUDED. See page 33-34 for faucet

options.

Medallion models feature 80mm illuminated LED

medallion holders. See page 21 for medallion options.



Winged Bridge “T”

Part Number Taps Finish Glycol Medallion

810-WBT-8BSS 8 Stainless $1,125.00 $1,599.00

810-WBT-8BPC 8 Chrome $1,225.00 $1,790.00

810-WBT-8BTF 8 TF Brass $1,395.00 $1,535.00


810-WBT-10BPC 10 Chrome $1,325.00 $1,875.00

810-WBT-10BTF 10 TF Brass $1,550.00 $2,080.00


810-WBT-12BPC 12 Chrome $1,495.00 $2,140.00

810-WBT-12BTF 12 TF Brass $1,695.00 $2,385.00


4” Column Dual Sided Pass-Thru


817-PTB8SS-DUAL 16 (8 per side) Stainless Steel $1,325.00







817-PTB24SS-DUAL 48 (24 per side) Stainless Steel $3,695.00Glycol Ready



with removeable lid

17” standard height

4” diameter chrome brushed pedestals



Includes standard American shanks and faucets.

Faucet handles not included.

#817-PTB18SS-DUAL has 3 - 4” chrome brushed pedestals

#817-PTB20SS-DUAL & #817-PTB24SS-DUAL have 4 - 4” chrome

brushed pedestals

All other variations have 2 - 4” chrome brushed pedestals

All configurations have the total number of lines evenly divided down

each pedestal. All configurations have 4 glycol lines per pedestal.


Add $21.00 per line for stainless steel faucets and shanks

Custom Draft Beer Towers

We work closely with our manufacturers to help ensure you receive exactly the look you want for your dispensing station. We

offer a wide variety of options to choose from, but in case you would like to have something in your bar, restaurant or home

that no one else has, call us today with your custom concept and let us bring it to life for you.

Note: Custom tower orders can take 2-12 weeks depending on concept and product availability


6

Draft Beer Towers: TMetropolis “T”

Glycol ready, Air Shaft or Medallion


16” Height to top of column; 15” Height to top

of crossbar

4” Diameter column

3” Cylindrical crossbar

Comes standard with American style faucets.


Medallion towers come with 80mm LED plug

and play medallion holders and are priced for

glycol ready towers. Air towers also available

with LED medallion holders. Custom acrylic

medallions available. Any brand or logo may

be printed onto medallion. See page 21 for

more information.


806-TR224-3NF 3 Stainless Steel $495.00




Terra “T” (NF)Glycol Ready

Faucet centers vary per tap configuration

(3-7/8” and 4-3/8”)

15-7/8” Height

3-3/16” Diameter columns





Other finishes available. Please call for more

information.

Terra “T” (Brewery Style)

Glycol Ready

Includes decorative flanges

18-1/2” Height






Optional “short” model:

11.7” Height (add suffix “-SH”)

Other finishes available. Please call for more

information.


806-TR224-3 3 Stainless Steel $495.00






Part Number Taps Finish Glycol Air Medallion

808-MET4TSS 4 Stainless Steel $805.00 $760.00 $1,295.00

808-MET6TSS 6 Stainless Steel $925.00 $885.00 $1,795.00

808-MET8TSS 8 Stainless Steel $1,065.00 $1,040.00 N/A

808-MET10TSS 10 Stainless Steel $1,205.00 N/A N/A


Winged “T”

Glycol ready


6-1/16” standard width

4-1/16” column width




options.


medallion holders. See page 21 for medallion options.



810-WTT-4BSS 4 Stainless $695.00 $950.00

810-WTT-4BPC 4 Chrome $750.00 $975.00

810-WTT-4BTF 4 TF Brass $875.00 $1,090.00

810-WTT-5BSS 5 Stainless $775.00 $1,055.00

810-WTT-5BPC 5 Chrome $825.00 $1,095.00

810-WTT-5BTF 5 TF Brass $950.00 $1,225.00


810-WTT-6BPC 6 Chrome $895.00 $1,215.00

810-WTT-6BTF 6 TF Brass $1,045.00 $1,355.00


810-WTT-8BPC 8 Chrome $1,050.00 $1,515.00

810-WTT-8BTF 8 TF Brass $1,225.00 $1,685.00

4-5/8” Square Column “T”



Optional “extra high” models for standard & wide

base models:




4-5/8” square column

7-5/8” square column for “wide base” version

(8,9,10 & 12 tap configurations ONLY)




FAUCETS NOT INCLUDED. See page 33-34 for

faucet options.


Draft Beer Towers: T


810-TT2SS 2 Stainless $395.00 N/A

810-TT2PC 2 Chrome $425.00 N/A

810-TT2TF 2 TF Brass $475.00 N/A

810-TT3SS 3 Stainless $385.00 $285.00

810-TT3PC 3 Chrome $445.00 $320.00

810-TT3TF 3 TF Brass $465.00 $400.00

810-TT4SS 4 Stainless $455.00 $340.00

810-TT4PC 4 Chrome $485.00 $370.00

810-TT4TF 4 TF Brass $535.00 $505.00

810-TT5SS 5 Stainless $575.00 $400.00

810-TT5PC 5 Chrome $625.00 $450.00

810-TT5TF 5 TF Brass $675.00 $585.00

810-TT6SS 6 Stainless $645.00 $505.00

810-TT6PC 6 Chrome $675.00 $565.00

810-TT6TF 6 TF Brass $745.00 $695.00

810-TT7SS 7 Stainless $695.00 N/A

810-TT7PC 7 Chrome $775.00 N/A

810-TT7TF 7 TF Brass $850.00 N/A


Draft Beer Towers: T & L3” Column “T”



3” Diameter brushed chrome column


with removeable lid




Other tap configurations available. Please call for

pricing.


shanks


817-TSCR-2 2 Stainless Steel $375.00 $300.00






4” Column “T”Glycol Ready or Air Shaft



with removeable lid




Other tap configurations available. Please call for

pricing.


shanks


817-LCTTB4SS 4 Stainless Steel $540.00 $475.00




Glycol Ready

Includes decorative flanges

18-1/2” Height






Optional “short” model:

11.7” Height

Available in Left or Right configurations. Please

specify when ordering.

Persey “L” (Brewery Style)


806-PS189-3 3 Stainless Steel $445.00



Left Configuration Right Configuration


Draft Beer Towers: Euro

Part Number Taps Finish Glycol806-MILANO-1 1 Chrome $245.00806-MILANO-2 2 Chrome $305.00806-MILANO-3 3 Chrome $395.00806-MILANO-4 4 Chrome $495.00806-MILANO-1-GD 1 PVD Gold $335.00806-MILANO-2-GD 2 PVD Gold $395.00806-MILANO-3-GD 3 PVD Gold $495.00806-MILANO-4-GD 4 PVD Gold $595.00

MilanoGlycol Ready

Made in Italy

16” Standard height


3/16” I.D Stainless Steel beer lines

Comes standard with American style faucets and

screw-in shanks. European faucet options available

at an additional charge. See page 33-34 for more

options.

Available with 80mm illuminated LED medallion

holders. Call for pricing.


Brigitte

Tango


808-TGO3461A 1 Stainless $345.00

See page 21 for medallion options


808-BGT-1C 1 Chrome $395.00 $595.00

808-BGT-2C 2 Chrome $895.00 N/A

808-BGT-3C 3 Chrome $925.00 $1,195.00

808-BGT-4C 4 Chrome $1,095.00 N/A

808-BGT-5C 5 Chrome $1,150.00 $1,550.00

808-BGT-6C 6 Chrome $1,350.00 N/A

808-BGT-7C 7 Chrome $1,550.00 $2,795.00

Glycol Ready

17-1/2” Standard height

3-1/4” Diameter column

Place 3 or 4 of these towers in a row over 1 drip tray for

maximum appeal

Built in 80mm LED medallion holder

Comes standard with American style faucet and shank.

European faucet options available at an additional

charge. See page 33-34 for more options. Faucet handle

not included.

Features a threaded mounting shank and nut for a bolt-

free installation

Glycol Ready or Illuminated Medallion

Made in Italy


4-1/8” Base diameter


screw-in shanks. European faucet options available at

an additional charge. See page 33-34 for more options.

Features a threaded mounting shank and nut for a

bolt-free installation

Note: 1 tap Brigitte tower with illuminated medallion

has medallion located on back side of tower opposite

the faucet and not the top like other tap

configurations.



Draft Beer Towers: EuroLucky

Part Number Taps Finish Glycol Air* Iced** Medallion Iced*/Medallion808-LT-1B 1 Chrome $410.00 $415.00 $425.00 $505.00 $595.00808-LT-2B 2 Chrome $470.00 $465.00 $495.00 $645.00 $725.00808-LT-3B 3 Chrome $560.00 $525.00 $595.00 $755.00 $995.00810-LT-1BGD 1 PVD Gold $430.00 $425.00 N/A Call N/A810-LT-2BGD 2 PVD Gold $495.00 $495.00 N/A Call N/A810-LT-3BGD 3 PVD Gold $590.00 Call N/A Call N/A

*Note: Air drawn towers are made for

mounting to 1-1/2” thick surfaces only.

Towers will only accept 1” vinyl blower

hose.

**Note: In order to build a layer of ice on

the exterior of a tower, an additional

power pack is required, located as

close as possible to the tower. For ice

to form, certain levels of humidity and

temperature must be achieved. A lack of

air movement is also required.

Medallion towers come with 80mm LED

plug and play medallion holders and are

priced for glycol ready towers. Air tow-

ers also available with LED medallion

holders. Custom acrylic medallions

available. Any brand or logo may be

printed onto medallion. See page 21 for

more information.

Glycol ready, Air, Iced or Medallion

Made in Italy

16-1/16” Standard height (non-medallion)

Comes standard with American style

faucets and screw-in shanks. European

faucet options available at an additional

charge. See page 33-34 for more

options.

Glycol ready, Air, Iced, Medallion

or Iced Medallion

Made in Italy





charge. See page 33-34 for more

options.

Panther*Note: Air drawn towers are made for



hose.















more information.

Part Number Taps Finish Glycol Air* Iced** Medallion Iced*/Medallion808-PT-3B 3 Chrome $670.00 $770.00 $730.00 $860.00 $840.00808-PT-4B 4 Chrome $770.00 $830.00 $820.00 N/A N/A810-PT-3BGD 3 PVD Gold $720.00 $930.00 N/A Call N/A810-PT-4BGD 4 PVD Gold $895.00 $1,040.00 N/A N/A N/A

SexyGlycol ready, Air, Iced, Medallion or Iced

Medallion

Made in Italy





charge. See page 33-34 for more options.

*Note: Air drawn towers are made for



hose.















more information.

Part Number Taps Finish Glycol Air* Iced** Medallion Iced*/Medallion808-SY-1C 1 Chrome $450.00 $460.00 $465.00 $585.00 $595.00808-SY-2C 2 Chrome $510.00 $515.00 $530.00 $690.00 $725.00808-SY-3C 3 Chrome $575.00 $565.00 $650.00 $835.00 $995.00808-SY-4C 4 Chrome $775.00 $770.00 $785.00 $960.00 $1,025.00808-SY-1GD 1 PVD Gold Call Call N/A Call N/A810-SY-2GD 2 PVD Gold $585.00 Call N/A Call N/A810-SY-3GD 3 PVD Gold $630.00 Call N/A $935.00 N/A808-SY-4GD 4 PVD Gold Call Call N/A $990.00 N/A

Note: PVD Gold towers stating to “call” are available as a custom order. Please call for current







Part Number Taps Finish Glycol Iced*806-COBRA-1 1 Chrome $515.00 $530.00806-COBRA-2 2 Chrome $795.00 $840.00806-COBRA-3 3 Chrome $995.00 $1,150.00806-COBRA-4 4 Chrome $1,195.00 $1,370.00806-COBRA-1-LED 1 Chrome $565.00 $690.00806-COBRA-2-LED 2 Chrome $895.00 $1,200.00806-COBRA-3-LED 3 Chrome $1,145.00 $1,650.00806-COBRA-4-LED 4 Chrome $1,395.00 $2,000.00806-COBRA-1-GOLD 1 PVD Gold $725.00 N/A806-COBRA-2-GOLD 2 PVD Gold $935.00 N/A806-COBRA-3-GOLD 3 PVD Gold $1,130.00 N/A806-COBRA-4-GOLD 4 PVD Gold $1,280.00 N/A

Cobra

Glycol Ready or Iced

17-5/8” Standard height for non-LED models

22” Standard height for LED models

3/8” I.D Copper coolant lines

3/16” I.D Stainless Steel beer lines


medallion holders. See page 21 for medallion

options.




options.

*NOTE: In order to build a layer of ice on the

exterior of a tower, an additional power pack is

required, located as close as possible to the tower.

For ice to form, certain levels of humidity and

temperature must be achieved. A lack of air

movement is also required.

Albatross “Y”


808-ALBTS-4 4 Stainless Steel $2,180.00808-ALBTS-6 6 Stainless Steel $2,370.00808-ALBTS-8 8 Stainless Steel $2,510.00808-ALBTS-10 10 Stainless Steel $2,725.00808-ALBTS-12 12 Stainless Steel $2,935.00808-ALBTS-14 14 Stainless Steel $3,085.00

Glycol Ready


14-3/8” Standard faucet height

4” Diameter columns with 6” diameter bolted flanges

6” Diameter base flange

Includes standard American faucets. Other faucet

options available. See page 33-34. Faucet handles

not included.

All models available with 80mm plug and play

illuminated medallions. Please call for pricing and

lead time.

Draft Beer Towers: Euro

Gothic

Glycol Ready


Chrome Finish standard. Available in Black, Gold or

Copper as a custom order. Please call for pricing and

lead time.




options.

Available with 80mm illuminated LED medallion

holders. Call for pricing.Part Number Taps Finish Glycol

806-GTH2CH 2 Chrome $395.00806-GTH3CH 3 Chrome $555.00806-GTH4CH 4 Chrome $650.00


Draft Beer Towers: Ceramic

Round CeramicGlycol Ready or Air Shaft

22” Height for 1-5 taps

20-1/2” Height for 6-8 taps


Features a threaded plastic mounting sleeve and nut

for a bolt-free installation

Trim available in Chrome or PVD gold. Please specify

when ordering.

Ceramic finish choices:

Beige Marble Add suffix (“-BM”)

Black Marble Add suffix (“-BK”)

Cobalt Blue Add suffix (“-CB”)

Pearl White Add suffix (“-PW”)

Antique Green Add suffix (“-AG”)

Part Number Taps Trim Glycol Air

801-CER-1 1 Chrome/Gold $995.00 $895.00

801-CER-2 2 Chrome/Gold $1,040.00 $940.00

801-CER-3 3 Chrome/Gold $1,095.00 $995.00

801-CER-4 4 Chrome/Gold $1,155.00 $1,055.00

801-CER-5 5 Chrome/Gold $1,235.00 $1,135.00

801-CER-L-6 6 Chrome/Gold $1,425.00 $1,325.00

801-CER-L-8 8 Chrome/Gold $,1555.00 $1,455.00

Ceramic “T”Glycol Ready or Air Shaft



Trim available in Chrome or PVD gold. Please








Ceramic “Pass-Thru”




Trim available in Chrome or PVD gold. Please









801-PTCEPVD-8 8 Chrome/Gold $2,295.00 $2,045.00





801-CEPVD-4 4 Chrome/Gold $1,325.00 $1,235.00





SilvaGlycol Ready or Air Shaft


5-1/8” Base diameter for 1-3 tap models

6-1/2” Base diameter for 4-8 tap models


Black Add suffix (“-BK”)

White Add suffix (“-WT”)

Red Add suffix (“-RD”)

1-3 tap models available in Chrome or Gold trim

4-8 tap models available in Chrome trim only

Gold is available as a custom order. Please allow

4-8 weeks.



806-SILVA-1 1 Chrome/Gold $325.00 $295.00



806-SILVA-4 4 Chrome $865.00 $755.00

806-SILVA-6 6 Chrome $960.00 $825.00

806-SILVA-8 8 Chrome $1,075.00 $920.00

TorinoGlycol Ready



Tarnish-free brass finish



Blue Add suffix (“-BL”)

Green Add suffix (“-GR”)

FAUCETS NOT INCLUDED. See page 33-34 for

faucet options.


Part Number Taps Trim Glycol

810-TC-1B 1 TF Brass $1,125.00

810-TC-2B 2 TF Brass $1,225.00

810-TC-3B 3 TF Brass $1,335.00

RomaGlycol Ready

Made in Italy



Available in Chrome or Tarnish-free brass finish



Black Add suffix (“-BK”)

Blue Add suffix (“-BL”)

Green Add suffix (“-GR”)



808-RMA3CH 3 Chrome $865.00

808-RMA3TF 3 TF Brass $865.00





Draft Beer Towers: Ceramic


Draft Beer Towers: Mushroom

Mini MushroomGlycol Ready or Air Shaft


7-3/8” Wide at top

6” Diameter base


faucets. Other faucet options available upon

request. Faucet handles not included.

Available in Stainless Steel as a custom order.

Please call for pricing and lead time.

Recommended for use with cut-out style or bar rail

type drip trays.


808-MMCH3 3 Chrome $755.00 $660.00

808-MMCH4 4 Chrome $795.00 $700.00



7-3/8” Wide at top

6” Diameter base


faucets. Other faucet options available upon

request. Faucet handles not included.

Available in Stainless Steel as a custom order.

Please call for pricing and lead time.

Recommended for use with cut-out style or bar rail

type drip trays.

Mushroom


808-DM-42CH 4 Chrome $895.00 $795.00

808-DM-52CH 5 Chrome $965.00 $850.00

808-DM-62CH 6 Chrome $1,025.00 $895.00

4” Wrap-Around


808-WA-4SS 4 Stainless Steel $495.00 $395.00

808-WA-4BR 4 PVD Brass $595.00 $495.00



4” Column diameter

6” Diameter base

Comes standard with American style shanks

and faucets. Other faucet options available upon

request.

Recommended for use with cut-out style drip

trays.

Note: Allow 3-4 weeks for PVD Gold towers


Draft Beer Towers: UnderbarPerlick Spacesaver Underbar Heads

Glycol Ready

UB13 Models have a 14” length and 13” face length

UB21 Models have a 22-1/4” length and 21-1/8” face length

4-5/8” Deep x 5-3/4” High on all variations

Stainless Steel finish

Available with lines extending out of back of the head or

bottom of the head. Please specify when ordering.


options

See below for Underbar Drainers


810-UB13-2 2 Stainless Steel $450.00









Part Number Finish Description Each

810-3713 Stainless Steel 13" Drip Pan w/skirt $450.00

810-3713-1* Stainless Steel 13" Drip Pan only $250.00

810-3721 Stainless Steel 21" Drip Pan w/skirt $475.00

810-3721-1* Stainless Steel 21" Drip Pan only $295.00

All Stainless Steel construction

Drainer for 13” underbar heads (drip pan only):

12-7/8” wide x 14-3/4” high

Drainer for 13” underbar heads (w/ skirt):

12-7/8” wide x 37-7/8” high

Drainer for 21” underbar heads (drip pan only):

21-1/8” wide x 14-11/16” high

Drainer for 21” underbar heads (w/skirt):

21-1/8” wide x 37-7/8” high

Drip trays are 18” wide x 8-1/2” deep with 7/8” diameter drains

*Optional stainless legs with rust-free adjustable feet available

Perlick Underbar Drainers for

spacesaver dispensing heads

Underbar DispenserGlycol Ready or Air Shaft

Comes with Stainless Steel mounting bracket

Air Shaft dispensers have a 3” diameter tube that is

mounted underneath the housing box. Tube can be or-

dered from 1”-10” in length . Please specify desired

length when ordering.

Comes standard with American style shanks and faucets

Add $21.00 per line for Stainless Steel

shanks and faucets

Optional Stainless Steel cover to

enclose sides of dispenser: $85.00

Optional second tube for Air Shaft: $30.00

Complete specifications available upon

request.

Part Number Taps Tray Size Glycol Air

817-LCUCDT15SS-2 2 15" $520.00 $470.00

817-LCUCDT15SS-3 3 15" $545.00 $490.00

817-LCUCDT15SS-4 4 15" $585.00 $520.00

817-LCUCDT24SS-5 5 24" $670.00 $580.00

817-LCUCDT24SS-6 6 24" $705.00 $600.00

817-LCUCDT30SS-8 8 30" $930.00 $790.00

817-LCUCDT36SS-10 10 36" $1,195.00 $1,010.00

817-LCUCDT36SS-12 12 36" $1,415.00 $1,260.00

16

Draft Beer Towers: Underbar & Wall Mount


Underbar Dispensing CabinetGlycol Ready or Air Shaft

16” Standard height 14” Standard depth (includes depth of cabinet plusdrip pan)3” Faucet centers on all tap configurations

May be ordered as a suspended wall cabinet or underbar cabinet. Please specify when ordering.

Cabinets come standard with a Stainless Steel driptray insert and a 1” diameter drain.

Cabinets may be ordered without faucets, shanksor tubing. Please call for pricing. Prices shown include American style faucets, shanks and tubing.

Optional support legs:4 support legs add $110 and suffix “-LG4”6 support legs add $145 and suffix “-LG6”


823-STC-6 6 Stainless Steel $995.00 $895.00823-STC-8 8 Stainless Steel $1,155.00 $1,025.00823-STC-10 10 Stainless Steel $1,365.00 $1,195.00823-STC-12 12 Stainless Steel $1,625.00 $1,415.00823-STC-14 14 Stainless Steel $1,945.00 $1,695.00823-STC-16 16 Stainless Steel $2,095.00 $1,810.00823-STC-18 18 Stainless Steel $2,350.00 $1,995.00823-STC-20 20 Stainless Steel $2,595.00 $2,225.00


860-HCUC-6 6 Maple $1,265.00 $995.00

860-HCUC-8 8 Maple $1,395.00 $1,050.00

860-HCUC-10 10 Maple $1,585.00 $1,155.00

860-HCUC-12 12 Maple $1,785.00 $1,275.00

Handcrafted Maple Underbar CabinetGlycol Ready or Air Shaft

Handcrafted in the Finger Lakes region of New York State with localMaple wood. Other choices of wood are available upon request.

15” Standard height (on models listed below)

12” Standard depth (on models listed below)

For Air ready models, please specify preferred location anddiameter for air tubing

Comes standard with American style shanks and faucets. Stainless Steel options available.

Complete customization available. Cabinets canbe built to customer specifications. Maple woodcabinets also available as countertop Irish Coffinboxes. Please call for pricing and specifications.Pictures available upon request. Please call formore information.

Part Number Tray Length Each817-WMDT-8 8" $140.00817-WMDT-15 15" $150.00817-WMDT-24 24" $185.00817-WMDT-30 30" $220.00817-WMDT-36 36" $260.00817-WMDT-48 48" $340.00

14 Gage Stainless Steel construction

Removable Stainless Steel louvered splash grid

1/2” MPT drain fitting included

Trays may be ordered blank or with holes punched to customers specifications:

8” tray (0-2 holes)15” tray (0-5 holes)24” tray (0-8 holes)30” tray (0-10 holes)36” tray (0-12 holes)48” tray (0-16 holes)

Please specify number of holes when ordering. Add $2.25per faucet hole. See page 32-34 for shanks & faucets.

Wall Mount Drip Tray

Note: Price shown is for wall mount drip tray without holes



817-LCWM15SS-2 2 Stainless Steel $475.00 $430.00






817-LCWM36SS-10 10 Stainless Steel $1,135.00 $950.00

817-LCWM36SS-12 12 Stainless Steel $1,345.00 $1,175.00


5-1/8” Deep x 4-1/8” High housing box

Stainless Steel construction

Can be mounted flush to any wall

Dispensers have a 3” diameter tube positioned in the backor bottom of the box. Tube can be ordered from 1”-10” inlength. Please specify length and desired location of tubewhen ordering.

Air ready dispensers have one tube for 2-6 tap models. 8and 10 tap models have two tubes.

Optional second tube for Air ready 2-6tap models: $30.00

Comes standard with American styleshanks and faucets.

Add $21.00 per line for Stainless Steelshanks and faucets

Add Suffix “-GR” for Glycol readyAdd Suffix “-AS” for Air ready

Wall Mount Dispenser with Drip Tray

Bar Top

FrontFaucetPanel

Drain &UnderbarSupport1” Lip

6” 61/2”

6”

8”

6”

41/2”


823-HHS-6 6 Stainless Steel $975.00 $890.00

823-HHS-8 8 Stainless Steel $1,130.00 $1,005.00







Sandwich Style CabinetGlycol Ready or Air Shaft

Air ready cabinets outfitted with two 4”holes; Glycol ready cabinets have one 4”hole. Specify hole position when ordering.

Comes standard with American styleshanks and faucets. Stainless Steel optionsavailable.

Add Suffix “-GR” for Glycol readyAdd Suffix “-AS” for Air ready

Other sizes available. Please call for moreinformation

Part Number Width Each

823-DHHS-6 19" $225.00823-DHHS-8 25" $250.00823-DHHS-10 31" $260.00823-DHHS-12 37" $315.00823-DHHS-14 43" Call823-DHHS-16 49" Call823-DHHS-18 55" Call823-DHHS-20 61" Call

Dispensing Panels

Drip Trays

Draft Beer Towers: Underbar & Wall Mount


Draft Beer Towers: Column Towers & Barrel Heads

Note: All towers are insulated and include Chrome plated brass American stylefaucets, shanks, mounting gasket, beer line and fittings. All towers include blackplastic knobs. Mounting screws not included. 2-1/2” column towers have a 3-1/2”base flange. 3” column towers have a 4-1/2” base flange. 4” column towers have a5-1/2” base flange. Other faucet options available. Please call for more information.

Part Number Taps Diameter Finish Glycol Air

800-150SS 1 2-1/2" Stainless $97.95 $69.95

800-618SS 1 3" Stainless $125.00 $79.95

800-619SS 2 3" Stainless $149.00 $105.95

800-620SS 3 3" Stainless $195.00 $169.95

817-720CH 3 4" Chrome $325.00 $295.00

801-618BR 1 3" Brass $139.00 $99.95

801-619BR 2 3" Brass $168.00 $129.95

801-620BR 3 3" Brass $230.00 $185.00

Barrel Head DispensersGlycol Ready or Air Shaft

Handcrafted in the Finger Lakes regionof New York State with local Maple

wood.Other choices of wood available upon

request.

Removable skirt for easy installationand accessibility.

Comes standard with American styleshanks and faucets. Stainless Steel

options available.

13” Face width (1-4 taps)

15” Face width (5 tap)

Please call for more specifications


860-BH-1 1 Maple $360.00 $270.00

860-BH-2 2 Maple $420.00 $300.00

860-BH-3 3 Maple $462.00 $330.00

860-BH-4 4 Maple $510.00 $360.00

860-BH-5 5 Maple $600.00 $450.00

Note: Other barrel head options available. Please call for more information.

800-150SS 800-618SS 800-619SS 800-620SS 817-720CH

Custom logo wrapping available for 3” column towers.Please call for more information. See page 21 for

medallion holders for column towers. Custom acrylicmedallions and tap handle branding also available.

Call for artwork requirements and pricing.

2-1/2”, 3” & 4” Column Towers

19

Tower Replacement Parts & Add-A-Faucet Kits

No. Part Number Description Each

1 801-1301 Black plastic faucet handle $1.95

2a 801-NS-1331 1-3/4" x 3/16" nipple tower shank only (Chrome) $12.95

2b 801-NS-1331XSST 1-3/4" x 3/16" nippletower shank only (Stainless) $16.95

3a 801-1332 Chrome coupling nut $2.15

3b 801-1332B Brass coupling nut $2.15

4a 801-1331F Curved plastic tower flange (Chrome) $4.50

4b 801-1331FB Curved plastic tower flange (Brass) $6.50

5 801-1345 Plastic spacer $1.20

6 801-1348TLN Tower lock nut $1.35

7a 817-GASK-150 2-1/2" Tower gasket $1.95

7b 817-GASK-618 3" Tower gasket $2.95

7c 808-GASK-8515 4" Tower gasket $4.95

8a 800-D12-2PA 2-1/2" Chrome "O" ring tower cap $5.95

8b 813-150CAP 2-1/2" Chrome tower cap $6.95

8c 800-D12-3PA 3" Chrome "O" ring tower cap $6.95

8d 813-618-CAP 3" Chrome tower cap $14.95

8e 813-618B-CAP 3" Brass tower cap $13.95

9a 852-INS-2 2-1/2" Tower insulation $4.95

9b 852-INS-3 3" Tower insulation $4.95

9c 852-INS-4 4" Tower insulation $5.95

Tower Replacement Parts

Add-A-Faucet Kits

Note: Add-A-Faucet kits fit 3” diameter towers only. Kits include insulated sleeve with 1/4” bore x 3/16” nipple shank assembly, mounting screws and metal drill bit. Faucets, beer line and cap is not included. To install, slide sleeve over exisiting column, fasten

set screws, add beer line and faucets, and reuse existing cap.

Part Number Finish Each

817-ZA-1C Chrome $49.95

801-ZA-1B Brass $59.95


817-ZA-2C Chrome $64.95

801-ZA-2B Brass $74.95


801-ZAL-2C Chrome $58.95

801-ZAL-2B Brass $59.95

Adds one product to a two producttower to make a three product tower

Adds one product by covering existing tower hole and making a

two product tower

Adds two products to an existing producthole to make a three product tower

Tower not included


1

2a

3a

4a

56

7b

8c

9b

20

Tower Shanks


Part Number Length Barb Size Each

801-1331S 1-3/4" 3/16" $12.95

801-1331SA 1-3/4" 1/4" $13.25

801-SS-1331S 1-3/4" 3/16" $15.95

801-1333S 3" 3/16" $15.95

801-1333SA 3" 1/4" $17.50

Tower Barbed Elbow Shanks

Part Number Length Barb Size Each

852-1331S-CC-3 1-3/4" 3/16" $22.95

852-1331S-CC-4 1-3/4" 1/4" $22.95

852-1331S-SC-3 1-3/4" 3/16" $23.95

852-1331S-SC-4 1-3/4" 1/4" $23.95

Note: Brass Sleeves available. Assemblies with “SC” have astraight sleeve for squared towers. Assemblies with “CC” have

a curved sleeve for cylindrical towers.

Perlick Century Shanks

Nipple Tower Shanks


801-NS-1331S Plated Brass $12.95

801-NS-1331XSST Stainless $19.95

852-NS-1331S-ASY Plated Brass $22.95

852-NS-1331XSST-ASY Stainless $27.95

Note: All Nipple tower shanks are 2-1/4” in length with 3/16”barbs. Straight sleeves and Brass sleeves are available. Pleasecall for pricing.

Note: All century shanks include rubber “O” ring. Screw inshanks for other European towers also available. Call for moreinformation.

Removable Elbow Tower Shank

12 3

4


1 813-747 1/4" O.D Stainless elbow $2.40

2 813-746 1/4" I.D Brass nut $1.55

3 813-745 1/4" I.D Rubber grommet $.65

4 813-1343 Short Tower shank only $15.95

801-1331SA801-1333S

852-1331S-CC-4 852-1331S-SC-4

801-NS-1331S801-NS-1331S-ASY

810-C27850

810-C27849

Part Number Length Finish Coupling Nut Each

810-C27849 1-1/2" Chrome Chrome $19.95

810-C27849PB 1-1/2" Brass Brass $19.95

810-SS-C27849 1-1/2" Stainless Chrome $24.95

810-SS-C27849PB 1-1/2" Stainless Brass $24.95

810-C27850 2-1/2" Chrome Chrome $22.95

810-C27850PB 2-1/2" Brass Brass $22.95

Tower Barbed Elbow Shank Assemblies

Part Number Description Each

801-865Set of 2 - 3" L x 2-3/8" W x 5/8" H Aluminum

Cooling Blocks$17.95

806-865-ROUND-THSet of 2 - 2" OD x 7/8" ID x 1/2" Thick

Threaded Aluminum Cooling Blocks$12.95

801-865 801-865-ROUND-TH

Aluminum Cooling Blocks


1 Covers pre-existing tower holes. Plates made of Stainless Steel. Includestwo 4” plates, one 2-1/2” long 10-24 thread phillips head bolt, one 10-24nylock nut, one lock washer and one flat washer.2 Includes four 2-1/2” long 10-24 thread phillips head bolts, four 10-24 nylock nuts, four lock washers and four flat washers.3 Adds restriction between choker line from dispenser and trunk line to

balance system. Kit includes: 2’ of 3/8” ID barrier tubing, 15 restrictor

segments, 2 -10.00mm clamps, 4 - 10.5mm clamps, 1 -14.0mm clamp,

1 - 1/4” x 1/4” S/S splicer, 1 - 3/8” x 1/4” S/S splicer and 3” piece of 3/16” ID

vinyl tubing.

Medallions

Non-LED Medallion Holders

Tower Parts & Medallions


852-THK-6A1 Stainless Steel Tower Hole Cover $6.95

848-TB-SET2 Tower Bolt Set $3.95

810-C649B3 Perlick Restrictor Kit $14.95

Tower Mounting Hardware & Restrictor Kits

3” Tower Caps with Medallion Holder


808-501220C 3 Way Chrome Medallion Holder Assembly $96.99808-501131C Chrome Extra Tall Medallion Holder $47.75808-501130C Chrome Tall Medallion Holder $48.25808-501125C Chrome Short Medallion Holder $42.75808-501101C Chrome S-Type Medallion Holder $51.77808-501320C Chrome Faucet Mount Medallion Holder $43.95808-501170C Chrome Screw Mount Medallion Holder $37.50

Note: Holders are to be used with 80 mm medallions. Oval shaped holders also available.Most holders also available with a gold finish. Please call for more information.


808-103440C 3" Diameter Chrome Tower Cap with 1 Sided Medallion Holder $45.21

808-103440BR 3" Diameter Brass Tower Cap with 1 Sided Medallion Holder $44.00

808-103442C 3" Diameter Chrome Tower Cap with 2 Sided Medallion Holder $44.50

808-103442BR 3" Diameter Brass Tower Cap with 2 Sided Medallion Holder $44.00

808-103470C* 3" Diameter Chrome Tower Cap with 2 Sided Lit LED Medallion Holder $122.00

808-501999 12V/5W/.1A LED Transformer with 115V Plug $33.95

*Tower cap requires 808-501999 LED transformer to light. Note: Holders are to be used with 80 mm medallions. Caps only fit towers that have 3” diameter columns.


808-X900210 Branded Acrylic Fish Eye Medallion $24.95

Note: 60mm, 80mm, 82mm and oval medallions available. Any brand or customlogo can be created onto acrylic medallions. Medallions are created to order.Customer must approve artwork prior to production. Custom logos must beprovided by customer as a Vector file (ESP,AI,PDF-CS5) or high resolutionimage (300 DPI - jpeg, png, tiff). Custom logos are subject to an artwork set upfee. Call for more information.

808-501220C

808-501131C 808-501130C 808-501125C 808-501101C

808-501320C 808-501170C

808-103440C 808-103470C

808-501999

852-THK-6A

848-TB-SET

810-C649B


Drip TraysSurface Mount Drip Trays with Drains

Part Number Finish Width Depth Height Each

817-LCDT8-S Stainless 8" 5-1/4" 3/4" $59.95

817-LCDT15-S Stainless 15" 5-1/4" 3/4" $69.95

817-LCDT24-S Stainless 24" 5-1/4" 3/4" $84.95

817-LCDT30-S Stainless 30" 5-1/4" 3/4" $94.95

817-LCDT36-S Stainless 36" 5-1/4" 3/4" $115.95

817-LCDT48-S Stainless 48" 5-1/4" 3/4" $144.95

817-LCDT60-S* Stainless 60" 5-1/4" 3/4" $219.95

*Tray has two drains. All other models have one drain.


808-DT-10S Stainless 10-1/4" 5-3/8" 3/4" $79.00

808-DT-15S Stainless 14-7/8" 5-3/8" 3/4" $89.00

808-DT-20S Stainless 20-1/4" 5-3/8" 3/4" $105.00

808-DT-24S Stainless 23-7/8" 5-3/8" 3/4" $115.00

808-DT-30S Stainless 30-1/4" 5-3/8" 3/4" $122.00

808-DT-36S Stainless 36-1/4" 5-3/8" 3/4" $132.00

808-DT-45S Stainless 45-1/4" 5-3/8" 3/4" $149.00


810-5015 Stainless 5-3/8" 4-7/8" 3/4" $102.00

810-5020 Stainless 13-3/4" 4-7/8" 3/4" $105.00

810-5025 Stainless 19" 4-7/8" 3/4" $110.00

810-5028 Stainless 24" 4-7/8" 3/4" $120.00

810-5030 Stainless 37" 4-7/8" 3/4" $159.00

810-5015TF PVD Brass 5-3/8" 4-7/8" 3/4" $180.00

810-5020TF PVD Brass 13-3/4" 4-7/8" 3/4" $190.00

810-5025TF PVD Brass 19" 4-7/8" 3/4" $205.00

810-5028TF PVD Brass 24" 4-7/8" 3/4" $250.00

810-5030TF PVD Brass 37" 4-7/8" 3/4" $375.00


834-609 Stainless 8-1/8" 5-3/8" 3/4" $33.95

834-616 Stainless 14-7/8" 5-3/8" 3/4" $39.95

834-616L Stainless 23-7/8" 5-3/8" 3/4" $46.95

834-616L-30 Stainless 30-1/4" 5-3/8" 3/4" $63.95

834-616L-36 Stainless 36-1/4" 5-3/8" 3/4" $73.95

834-609B Brass 8-1/8" 5-3/8" 3/4" $67.95

834-616B Brass 14-7/8" 5-3/8" 3/4" $71.95

834-616LB Brass 23-7/8" 5-3/8" 3/4" $92.95

834-616LB-30 Brass 30-1/4" 5-3/8" 3/4" $104.95

834-616LB-36 Brass 36-1/4" 5-3/8" 3/4" $130.95

Note: Stainless trays come standard with White plastic grids. Brass trays comestandard with Black plastic grids. Stainless Steel and Brass grid inserts available.See page 27.

Note: All drip trays feature no-sag stainless steel grid inserts



806-DTU12SS Stainless 12" 7-1/4" 3/4" $62.00

806-DTU16SS Stainless 16" 7-1/4" 3/4" $70.00

806-DTU20SS Stainless 20" 7-1/4" 3/4" $135.00

806-DTU24SS Stainless 24" 7-1/4" 3/4" $155.00

806-DTU36SS Stainless 36" 7-1/4" 3/4" $170.00

806-DTU45SS Stainless 45" 7-1/4" 3/4" $195.00

806-DTU48SS Stainless 48" 7-1/4" 3/4" $205.00


810-C18635 Stainless 8-3/4" 7-3/4" 3/4" $115.00

810-C18640 Stainless 14-13/16" 7-3/4" 3/4" $125.00

810-C18645 Stainless 20-3/4" 7-3/4" 3/4" $135.00

810-C18650 Stainless 26-3/4" 7-3/4" 3/4" $175.00

810-C18655 Stainless 33" 7-3/4" 3/4" $180.00

810-C18660 Stainless 46-9/16" 7-3/4" 3/4" $230.00

810-C18635TF PVD Brass 8-3/4" 7-3/4" 3/4" $230.00

810-C18640TF PVD Brass 14-13/16" 7-3/4" 3/4" $245.00

810-C18645TF PVD Brass 20-3/4" 7-3/4" 3/4" $255.00

810-C18650TF PVD Brass 26-3/4" 7-3/4" 3/4" $350.00

810-C18655TF PVD Brass 33" 7-3/4" 3/4" $360.00


817-LCDTW20-S Stainless 20" 8" 3/4" $129.95





817-LCDTW62-S* Stainless 62" 8" 3/4" $255.00

817-LCDTW76-S* Stainless 76" 8" 3/4" $325.00

*Tray has two drains. All other models have one drain.

Surface Mount Drip Trays with Drains

Drip Trays


808-DTW-12S Stainless 12” 7" 3/4" $104.00

808-DTW-16S Stainless 16" 7" 3/4" $115.00

808-DTW-20S Stainless 20" 7" 3/4" $119.00

808-DTW-24S Stainless 24" 7" 3/4" $125.00

808-DTW-30S Stainless 30" 7" 3/4" $134.00

808-DTW-36S Stainless 36" 7" 3/4" $145.00

808-DTW-45S Stainless 45" 7" 3/4" $169.00

Note: All drip trays feature no-sag stainless steel grid inserts

24

Surface Mount Drip Trayswithout Drains



808-DT-10S-ND Stainless 10-1/4" 5-3/8" 3/4" $69.00

808-DT-15S-ND Stainless 14-7/8" 5-3/8" 3/4" $83.00

808-DT-20S-ND Stainless 20-1/4" 5-3/8" 3/4" $89.00

808-DT-24S-ND Stainless 23-7/8" 5-3/8" 3/4" $105.00

808-DT-30S-ND Stainless 30-1/4" 5-3/8" 3/4" $109.00


834-608 Stainless 8-1/8" 5-3/8" 3/4" $30.50

834-615 Stainless 14-7/8" 5-3/8" 3/4" $34.95

834-615L Stainless 23-7/8" 5-3/8" 3/4" $41.95

834-615L-30 Stainless 30-1/4" 5-3/8" 3/4" $58.95

834-615L-36 Stainless 36-1/4" 5-3/8" 3/4" $68.95

834-608B Brass 8-1/8" 5-3/8" 3/4" $62.95

834-615B Brass 14-7/8" 5-3/8" 3/4" $64.95

834-615LB Brass 23-7/8" 5-3/8" 3/4" $87.95

834-615LB-30 Brass 30-1/4" 5-3/8" 3/4" $99.95

834-615LB-36 Brass 36-1/4" 5-3/8" 3/4" $125.95

Flush Mount Drip TraysPart Number Finish Width Depth Height Each

810-C32357 Stainless 18-13/16" 5-1/8" 3/4" $165.00

810-C58979 Stainless 37-5/16" 5-1/8" 3/4" $165.00

810-C32357TF PVD Brass 18-13/16" 5-1/8" 3/4" $315.00

810-C58989TF PVD Brass 37-5/16" 5-1/8" 3/4" $365.00


834-609F Stainless 8-1/8" 5-3/8" 3/4" $41.95

834-616F Stainless 14-7/8" 5-3/8" 3/4" $49.95

834-616FL Stainless 23-7/8" 5-3/8" 3/4" $55.95

834-616FL-30 Stainless 30-1/4" 5-3/8" 3/4" $69.95

834-616FL-36 Stainless 36-1/4" 5-3/8" 3/4" $74.95

834-609FB Brass 8-1/8" 5-3/8" 3/4" $75.95

834-616FB Brass 14-7/8" 5-3/8" 3/4" $84.95

834-616FLB Brass 23-7/8" 5-3/8" 3/4" $110.95

834-616FLB-30 Brass 30-1/4" 5-3/8" 3/4" $114.95

834-616FLB-36 Brass 36-1/4" 5-3/8" 3/4" $135.95


810-C11988 Stainless 8-3/4" 7-5/8" 3/4" $95.00

810-C21379 Stainless 14-13/16" 7-5/8" 3/4" $110.00

810-C32257 Stainless 20-5/8" 7-5/8" 3/4" $125.00

810-C11988TF PVD Brass 8-3/4" 7-5/8" 3/4" $218.00

810-C21379TF PVD Brass 14-13/16" 7-5/8" 3/4" $235.00

810-C32257TF PVD Brass 20-5/8" 7-5/8" 3/4" $265.00

Note: Stainless trays come standard with White plastic grids. Brass trays comestandard with Black plastic grids. Stainless Steel and Brass grid inserts available.See page 27. All trays include rubber feet.

Note: All trays include rubber feet and have no-sag stainless steel grid inserts.

Note: Stainless trays come standard with White plastic grids. Brass trays comestandard with Black plastic grids. Stainless Steel and Brass grid inserts available.See page 27.

Drip Trays



808-DTGWS-88 Stainless 8" 8" 3/4" $134.95

808-DTGWS-88CM Stainless 8" 8" 3/4" $148.95

808-DTGWS-12S Stainless 12" 7" 3/4" $144.95

808-DTGWS-16S Stainless 16" 7" 3/4" $149.95

808-DTGWS-20S* Stainless 20" 7" 3/4" $154.95





Surface Mount Drip Trays withGlass Rinser


806-DTU20SSR Stainless 20" 7-1/4" 3/4" $195.00






810-43839 Stainless 16" 16" 7/8" $225.00

810-43840 Stainless 23-3/4" 16" 7/8" $285.00

810-43840-R* Stainless 23-3/4" 16" 7/8" $305.00

810-43839GD PVD Gold 16" 16" 7/8" $275.00

810-43840GD PVD Gold 23-3/4" 16" 7/8" $330.00

*Tray comes with glass rinser centered on drip tray.

Part Number Finish Glass Rinser Width Depth Height Each

806-DTF16SS Stainless No 15-3/4" 15-3/4" 7/8" $140.00




806-DTF16SSR Stainless Yes 15-3/4" 15-3/4" 7/8" $185.00




Tower Mount Drip Trays

*Sprayer is side mounted. All other models have centered sprayers.

Note: “CM” model comes with a 8” x 4-1/2” counter mounting plate.

Note: Drip pans are meant to be used with Lucky, Panther & Sexy towers. All 23-3/4”wide trays are not recommended for use with two 4 faucet panther towers.

Note: Drip pans are meant to be used with most Euro Style Towers. Trays can be orderedwith or without predrilled tower mounting hole. Please specify when ordering.

Note: All models have centered sprayers.

Angled Drip Tray


810-57120 Stainless 19-1/4" 6-1/2" 7/8" $195.00

810-57120TF PVD Brass 19-1/4" 6-1/2" 7/8" $315.00

Note: Stainless trays come standard with White plastic grids. Brass trays comestandard with Black plastic grids. Drip tray is ideal for Mushroom and Ceramicstyle towers. Includes 4” x 1/2” MPT drain fitting.

Drip Trays

26

Part Number Finish Width Depth Height Cut-Out Radius Each

810-66596 Stainless 14" 8" 7/8" 6" $230.00

810-62303 Stainless 19-3/4" 10" 7/8" 8-1/2" $295.00

810-62304TF PVD Brass 19-3/4" 10" 7/8" 10" $295.00

810-62303TF PVD Brass 19-3/4" 10" 7/8" 8-1/2" $235.00

810-66596TF PVD Brass 14" 8" 7/8" 6" $285.00


808-1574 Stainless 15" 7-1/2" 7/8" 4-1/2" $205.00

808-1896 Stainless 18" 9" 7/8" 6-1/4" $220.00


808-701713 Stainless 14" 8" 3/4" 6" $170.00

808-701110 Stainless 15" 7-1/2" 7/8" 4-1/2" $205.00

808-701125 Stainless 18" 9" 7/8" 6-1/4" $225.00

808-701719 Stainless 19" 9" 7/8" 6-1/4" $250.00

808-701150 Stainless 19-3/4" 10" 7/8" 8-1/4" $225.00

808-701221 Stainless 24" 11" 7/8" 7-1/2" $295.00

808-701718 Stainless 18" 9" 7/8" 5-3/4" $255.00

808-701145 Stainless 19-1/4" 10" 7/8" 6-1/2" $195.00

808-701713BR PVD Brass 14" 8" 3/4" 6" $305.00

808-701718BR PVD Brass 18" 9" 7/8" 5-3/4" $355.00

808-701719BR PVD Brass 19" 9" 7/8" 6-1/4" $355.00

808-701721BR PVD Brass 24" 11" 7/8" 7-1/2" $395.00

Part Number Finish Width Depth Height Cut-Out Radius Price

808-1574-SPRAY Stainless 15" 7-1/2" 7/8" 4-1/2" $225.00

808-1896-SPRAY Stainless 18" 9" 7/8" 6-1/4" $250.00

Drip TraysCut-Out Style Drip Trays

with Drains


834-MDT-19S Stainless 19" 8-1/8" 3/4” 6" $102.95

834-MDT-19B PVD Brass 19" 8-1/8" 3/4” 6" $146.95

Cut-Out Style Drip Trayswithout Drains

Cut-Out Style Drip Trayswith Glass Rinser & Drain

Note: Stainless trays come standard with White plastic grids. Brass trays come standardwith Black plastic grids. Stainless Steel and Brass grid inserts available. Please call forpricing.


Note: Drip trays include a 2” x 1/2” MPT brass drain fitting.

Note: Please allow 3-4 weeks for PVD Brass drip trays.

27

Drip Tray Accessories & Replacement Parts

Part Number Finish Width Depth Each

834-GSS-85 Stainless 8-1/8" 5-1/8" $20.75

834-GSS-145 Stainless 14-7/8" 5-1/8" $24.75

834-GSS-245 Stainless 23-7/8" 5-1/8" $33.50

834-GSS-305 Stainless 30-1/4" 5-1/8" $41.75

834-GSS-365 Stainless 35-7/8" 5-1/8" $51.00

834-GBR-85 PVD Brass 8-1/8" 5-1/8" $29.00

834-GBR-145 PVD Brass 14-7/8" 5-1/8" $36.50

834-GBR-245 PVD Brass 23-7/8" 5-1/8" $50.50

834-GBR-305 PVD Brass 30-1/4" 5-1/8" $62.50

834-GBR-365 PVD Brass 35-7/8" 5-1/8" $79.00

Part Number Plastic Color Width Depth Each

834-WEC-508 White 8-1/8" 5-1/8" $9.45

834-WEC-515 White 14-7/8" 5-1/8" $10.45

834-WEC-524 White 23-7/8" 5-1/8" $11.45

834-WEC-530 White 30-1/4" 5-1/8" $12.45

834-WEC-536 White 35-7/8" 5-1/8" $13.45

834-BEC-508 Black 8-1/8" 5-1/8" $12.45

834-BEC-515 Black 14-7/8" 5-1/8" $13.45

834-BEC-524 Black 23-7/8" 5-1/8" $15.45

834-BEC-530 Black 30-1/4" 5-1/8" $15.45

834-BEC-536 Black 35-7/8" 5-1/8" $17.45



801-TDN-3 3-1/2" replacement drain assembly $16.95

801-TDN-6 6" replacement drain assembly $19.95

801-TDN-8 8" replacement drain assembly $23.95

1 2


1 806-RIN-M Glass Rinser Assembly w/ Metal Arms $54.95

2 808-RIN-P Glass Rinser Assembly w/ Plastic Arms $49.95


1 801-205B-L2 2" x 1/2" MPT Brass drain assembly $6.95

801-205B-L4 4" x 1/2" MPT Brass drain assembly $13.25

801-205B-L6 6" x 1/2" MPT Brass drain assembly $18.95

2 801-1360 Rubber washer for 1/2" MPT drain fitting $.95

3 801-1348 Lock nut for 1/2" MPT drain fitting $1.95

2 3


834-205P-2 2" x 1/2" MPT Plastic drain assembly $12.95


805-JG214 3/8" OD x 1/2" BSP Female connector $3.95

805-JG614 1/2" OD x 1/2" BSP Female connector $4.95


805-205S-ELB 1/2" FPT x 1/2" Barb PVC elbow hose adapter $3.95


805-205S-STR 1/2" FPT x 1/2" Barb PVC straight hose adapter $4.95


855-CAPSS-10 10 oz. Tube of Clear Silicone Sealant $6.95


1 833-205-151A 1/2" FPT Plastic 45° drain adapter $4.05

2 833-205-150A 1/2" MPT fitting for #205-151A adapter $4.05

1

2

834-GSS-85 834-WEC-508

1

801-TDN-6

805-JG214

See page 47 for John Guest barbed fittings

28

Couplers

No. Part Number Description 1-23 24 +

1 800-CH5000 Taprite US Sankey Coupler w/ white handle $26.25 $24.25

2 801-LT18GS-SH American Beverage US Sankey Coupler w/ short handle $26.25 $24.25

3 810-36000GS Perlick US Sankey Coupler w/ 304 SS Probe $44.95 $41.95

“D” Type - Lever Handle

“S” Type - Lever Handle

1

2

3


4 800-CH5100 Taprite Euro Sankey Coupler $26.95 $24.95

5 801-LT46GS American Beverage Euro Sankey Coupler $28.25 $26.25

4

5


6 801-FT86P American Beverage US Sankey Coupler w/ Plastic Wing $25.95 $23.95

7 801-FT86M American Beverage US Sankey Coupler w/ Metal Wing $29.50 $27.50

“D” Type - Wing Handle

6

“S” Type - Wing Handle


8 801-FT90P American Beverage Euro Sankey Coupler w/ Plastic Wing $29.50 $27.50

9 801-FT90M American Beverage Euro Sankey Coupler w/ Metal Wing $33.50 $31.50

8 97


10 800-EURO-A Taprite Euro Type "A" coupler $59.95 $54.95

11 800-EURO-U Taprite Euro Type "U" coupler $62.95 $57.95

12 800-EURO-G Taprite Euro Type "G" coupler $59.95 $54.95

European


13 810-FT44T Perlick US Sankey Low Profile Coupler $49.95 $44.50

Low Profile

10 11 12 13


See page 87 for the Coupler Master List

Note: 801-CH5000 available with a locking arm assembly. Call for pricing. Other handle colors availableupon request.

29

Coupler Replacement Parts


Taprite CH5000 & CH5100

American Beverage LT18GS & LTP-1

PERLICK 36000GS

1

2

3

4

6

7a

89

10

11

12

5a,b

5c

7b

1a,b

2

3

4

5

6

7

89

10

1112

1314

15

12

3

4 5

6

7 89

10

11

12

13


1 800-GR-110 Handle Assembly $10.95 N/A

2 800-GR-109 Handle Pin $2.95 N/A

3 800-GR-99 Ball Stop $.72 $.62

4 800-909B Ball $.72 $.62

5a 800-GR-114M "D" Type Probe Assembly - Brass $12.25 N/A

5b 800-GR-114S "D" Type Probe Assembly - Stainless $25.50 N/A

5c 800-GR-115M "S" Type Probe Assembly - Brass $13.50 N/A

6 815-FT-101 Probe "O" Ring (3 required) $.59 $.39

7a 801-FT-103 US Probe Seal $.65 $.55

7b 801-FT-104 Euro Probe Seal $1.40 $1.20

8 802-218 Hex Nut $.79 N/A

9 800-GR-105 Air Nipple $1.95 N/A

10 800-GR-107 Check Valve $1.15 $1.05

11 800-GR-PRV Pressure Relief Valve Assembly $5.45 N/A

12 800-108 Body Seal $.91 $.81


1a 801-55H-S Short Plastic Handle Sleeve $1.95 N/A

1b 801-55H-L Long Plastic Handle Sleeve $1.95 N/A

2 801-LT-8NAGS Handle Assembly $9.95 N/A

3 801-LT-2A Handle Pin & Lock Nut $1.50 N/A

4 801-FT-113GS Ball Retainer $.65 $.55

5 800-909B Ball $.72 $.62

6 815-FT-102 Body "O" Ring (3 required) $.59 $.39

7 801-FT-103 US Probe Seal $.65 $.55

8 801-FT-115GS Pressure Relief Valve Assembly $4.25 N/A

9 802-218 Hex Nut $.79 N/A

10 802-216D 5/16" Air Nipple $.77 $.70

11 801-FT-106 Check Valve Retainer $.85 $.70

12 801-23 Check Valve $.46 $.42

13 801-FT-106ASY Check Valve Assembly $1.25 $1.10

14 800-108 Body Seal $.91 $.81

15 801-LT-9AB "D" Type Probe Assembly - Brass $10.95 N/A


1 810-43641-1 Ball Retaining Spring $1.10 $1.00

2 810-31080-2P Ball $1.15 N/A

3 810-40174-1 "D" Type Probe Assembly - Stainless $22.95 N/A

4 810-31084-1 Handle Pin $1.81 N/A

5 810-31089-2P Body "O" Ring (3 required) $.69 $.65

6 810-43001A Handle Assembly $17.95 N/A

7 802-218 Hex Nut $.79 N/A

8 802-216D 5/16" Air Nipple $.77 $.70

9 801-24R Rubber Washer $.30 N/A

10 810-23682 Check Valve $1.45 N/A


12 800-108 Body Seal $.91 $.81

13 801-FT-103 US Probe Seal $.65 $.55

30

Coupler Replacement Parts


American Beverage FT86, FT90 & SP-1


1 800-55004 Ball Retainer $1.752 800-55005 Ball $2.553 800-GR-109 Handle Pin $2.954 800-GR-PRV Pressure Relief Valve Assembly $5.455 800-GR-107 Check Valve $1.156 802-216D 5/16" Air Nipple $.777 802-218 Hex Nut $.798 800-55007 "A" Type Probe "O" Ring (2 required) $1.109 800-55008 "A" Type Bottom Seal $4.35


1 800-55004 Ball Retainer $1.752 800-55005 Ball $2.553 800-GR-109 Handle Pin $2.954 800-GR-PRV Pressure Relief Valve Assembly $5.455 800-GR-107 Check Valve $1.156 802-216D 5/16" Air Nipple $.777 802-218 Hex Nut $.798 800-55007 "G" Type Probe "O" Ring (2 required) $1.109 800-55008 "G" Type Bottom Seal $4.35


1 800-55004 Ball Retainer $1.752 800-55005 Ball $2.553 800-GR-109 Handle Pin $2.954 800-GR-PRV Pressure Relief Valve Assembly $5.455 800-GR-107 Check Valve $1.156 802-216D 5/16" Air Nipple $.777 802-218 Hex Nut $.798 800-55017 "U" Type Probe "O" Ring (3 required) $1.109 800-55019 "U" Type Bottom Seal $3.95

Taprite Euro “A”

Taprite Euro “G”

Taprite Euro “U”

1

2a,b

3

4

5

6

7

89

10a10b

11

11

12

13

14a 14b

15

1

2 3

4

56

78

9

1

2

3

4

567

8

9

1

2 3

4

5 6

78

9


1 800-FT-114 Handle Retaining Ring $1.25 $1.05

2a 801-FT-88P Plastic Wing Handle $3.25 N/A

2b 801-FT-88M Metal Wing Handle $7.95 N/A

3 801-1328 Snap Ring $.49 $.45

4 801-FT-98 Spring $1.15 $1.10

5 802-218 Hex Nut $.79 N/A

6 802-216D 5/16" Air Nipple $.77 $.70

7 800-GR-107 Check Valve $1.15 $1.05

8 800-108 Body Seal $.91 $.81


10a 801-FT-103 US Probe Seal $.65 $.55

10b 801-FT-104 Euro Probe Seal $1.40 $1.20

11 815-FT-101 Probe "O" Ring (2 required) $.59 $.39

12 800-FT-2DB Ball $.75 $.65

13 800-FT-113 Ball Retainer $.65 $.55

14a 801-FT-118 "D" Type Probe Assembly - Brass $11.50 N/A

14b 801-FT-118E "S" Type Probe Assembly - Brass $13.50 N/A

15 801-45-LR Lexan Spring Support Ring $.95 $.85

31

Coupler Replacement Parts & Accessories


1 826-102-526 Body "O" Ring (2 required) $1.55

2a 826-102-376 US Probe Seal $1.45

2b 826-102-522 Euro Probe Seal $2.25

3 826-102-530 Clear Check Valve $1.75

4 826-403-014 Handle Assembly (Black) $12.50

5 826-102-521 Body Seal $1.55

Micromatic US Sankey & Euro Sankey

Perlick Test Coupler


810-32700B Test Coupler Kit w/ "D" Type Probe $149.95

810-31478-1 Probe Tip for Euro "S" Type Kegs $5.95

810-26159B Test Coupler w/ "D" Type Probe Only $125.95

810-26159B

Hoff Stevens Twin Probe


801-17 Hoff Stevens Figure 8 Washer $1.50

801-18HS Hoff Stevens Check Valve $1.95


1 801-760 Single Beer Shut-Off with Handle $18.50

2 801-132 Beer "Y" $16.50

3 800-FT-872 Female Beer Thread x Male Beer Thread Elbow $12.75


4 800-FT101L 1 oz. Can of Probe Lubricant $3.95

5 800-FT938L 8 oz. Can of Probe Lubcricant $15.95

6 855-SLO-4 USDA Approved Clear Synthetic Liquid Oil $7.95

1 2

3

4 5

6


1

2a2b

43

5

810-32700B

801-17

801-18HS

Coupler Fittings

Coupler Lubricants

32

Shanks

1 2 3 5a,b 6a,b 7

Part Number Description Nipple Size Each

801-NS-225A 1-3/4" Long x 1/4" Bore 3/16" $17.45

801-NS-250B 2-1/2" Long x 1/4" Bore 3/16" $13.95

801-NS-200A 2-7/8" Long x 3/16" Bore 3/16" $12.95

801-NS-200B 2-7/8" Long x 1/4" Bore 1/4" $12.95

801-NS-350A 3-1/2" Long x 3/16" Bore 3/16" $12.95

801-NS-350B 3-1/2" Long x 1/4" Bore 1/4" $12.95

801-NS-438A 4-5/8" Long x 3/16" Bore 3/16" $14.95

801-NS-438B 4-5/8" Long x 1/4" Bore 1/4" $14.95

801-NS-550A 5-1/8" Long x 3/16" Bore 3/16" $15.95

801-NS-550B 5-1/8" Long x 1/4" Bore 1/4" $15.95


801-SS-1361B 2" Long x 1/4" Bore $16.95801-SS-1363B 3" Long x 1/4" Bore $18.95801-SS-1364B 4" Long x 1/4" Bore $21.95801-SS-1367B 6" Long x 1/4" Bore $26.95801-SS-1368B 8" Long x 1/4" Bore $42.95

Chrome Plated Brass Shanks

Chrome Plated Brass Nipple Shanks

Stainless Steel Shanks

8 9 10a,b

Shotgun Shanks

Shank Replacement Parts & Accessories4a,b,c


831-SG-P1Plastic Triangular Insert

for Shotgun Shanks

$.99

Part Number Description 1-5 6 +

801-1363A 3" Long x 3/16" Bore $10.95 $10.50

801-1363B 3" Long x 1/4" Bore $10.95 $10.50

801-1364A 4" Long x 3/16" Bore $12.95 $11.95

801-1364B 4" Long x 1/4" Bore $12.95 $11.95

801-1366A 5" Long x 3/16" Bore $14.95 $13.95

801-1366B 5" Long x 1/4" Bore $14.95 $13.95

801-1367A 6" Long x 3/16" Bore $16.25 $15.25

801-1367B 6" Long x 1/4" Bore $16.25 $15.25

801-1368A 8" Long x 3/16" Bore $18.95 $17.95

801-1368B 8" Long x 1/4" Bore $18.95 $17.95

801-1370B 10" Long x 1/4" Bore $23.95 $22.95

801-1371B 12" Long x 1/4" Bore $27.95 $26.95

801-1372B 14" Long x 1/4" Bore $30.95 $29.95

801-1374B 16" Long x 1/4" Bore $37.95 $36.95

801-1376B 18" Long x 1/4" Bore $43.95 $42.95

801-1367B


1 801-1348 Lock Nut $1.25 $1.10

2 801-1348-LW Lock Washer $.95 $.85

3 801-1360 Rubber Shank Washer $.95 N/A

4a 801-1346P Black Plastic Flange $1.50 $1.25

4b 801-1346BR Brass Plastic Flange $2.10 $2.00

4c 801-1346 Stainless Steel Flange $2.50 $2.25

5a 801-1332 Chrome Coupling Nut $2.05 $1.95

5b 801-1332B Brass Coupling Nut $2.05 $1.95

6a 801-1330 Chrome Coupling Sleeve $.95 $.90

6b 801-1330B Brass Coupling Sleeve $.95 $.90

7 801-1328 Snap Ring $.65 $.55

8 800-610BL Locking Flange $11.95 $10.95

9 817-TMPA-1 1" Aluminum Spacing Sleeve $7.95 $7.25

10a 801-TMCH-34 3/4" Chrome Plastic Spacing Sleeve $6.95 N/A

10b 801-TMBR-34 3/4" Brass Plastic Spacing Sleeve $7.25 N/A

11 801-1334 Flange Washer $.75 $.65

801-SS-1364B

Note: All shanks are 304 stainless steel.

11

801-NS-350B

801-SG-DF1-S

Part Number Description Finish Each

801-SG-DF1-D 1" Shank with Tubes Bent Down Chrome $75.95

801-SG-DF1-S 1" Shank with Tubes Bent to Side Chrome $75.95

801-SG-DF2 2" Shank with Tubes Straight Out Back Chrome $82.95

801-BSG-DF2 2" Shank with Tubes Straight Out Back Brass $82.95













33

FaucetsDomestic Faucets

801-660B



801-660B Chrome Plated Faucet with Brass Lever $13.75 $11.75

801-660B-SS Chrome Plated Faucet with Stainless Lever $15.75 $13.75

800-SS-660B 304 Stainless Steel Faucet with Stainless Lever $33.95 $31.95

801-660BR Brass Faucet with Brass Lever $16.95 $15.95

801-660BR-SS Brass Faucet with Stainless Lever $18.95 $17.95

801-660GD Gold Plated Faucet with Brass Lever $24.60 $22.60

801-660GD-SS Gold Plated Faucet with Stainless Lever $26.15 $24.15

810-630SS Perlick 630 Series Stainless Steel Faucet with Stainless Lever $44.95 $42.95

810-630SSTF Perlick 630 Series Tarnish-Free Brass Faucet with Stainless Lever $48.95 $45.95

810-650SS Perlick 650 Series Stainless Steel Flow Control Faucet with Stainless Lever $54.95 $51.95

810-680SS Perlick 630 Series Stainless Steel Faucet with Push-Back Creamer Lever $47.95 $44.95

810-690SS Perlick 650 Series Stainless Flow Control Faucet with Push-Back Creamer Lever $64.95 $60.95

808-VSQTSS Vin Service Quix Tap 304 Stainless Steel Faucet $49.95 $46.95

863-MAXI-VAC Maxi-Vac 304 Stainless Steel Perfect Pour Faucet $125.00 Call

810-680SS

810-650SS

Faucet handle not included

808-VSQTSS

810-630SS

800-SFSSB-1

Stout Faucets


800-SFSSB-1 Taprite Stainless Stout Faucet with Stainless Nozzle $79.95

800-SFGDB-1 Taprite PVD Gold Stout Faucet with Stainless Nozzle $79.95

800-SFGDB-1

Note: All Perlick faucets are 304 stainless steel. The top of the 800-SS-660B is squared and not rounded like the801-660B faucet. 863-MAXI-VAC faucet uses the same replacement parts as the 801-660B faucet. See Page 34-36for all replacement parts. Other faucet styles available. Please call for more information.

863-MAXI-VAC

800-SS-660B

Note: See page 36 for stout faucet replacement parts.

34


808-EUT-221C* Chrome Euro Faucet with Stainless Nozzle and Flow Control Lever $80.95

808-EUT-221G* Gold Euro Faucet with Stainless Nozzle and Flow Control Lever $80.95

808-EUT-218C* Chrome Euro Faucet with Black Nozzle and Flow Control Lever $79.95

808-EUT-218G* Gold Euro Faucet with Black Nozzle and Flow Control Lever $79.95

808-VSQTSS-C* Vin Service Quix Tap 304 Stainless Steel Faucet with Flow Control Lever $89.95

Faucets & Faucet Replacement PartsEuropean Flow Control Faucets with Shanks

European Faucets with US Threads


808-UST-234C Chrome Euro Faucet with Stainless Nozzle $54.95

808-UST-233G Gold Euro Faucet with Stainless Nozzle $74.95

808-EUT-221C

808-EUT-218C808-VSQTSS-C

808-UST-234C


*Faucet Lever Handles not included. Faucets come with 7/8” x 1-3/4” S/S shank and European coupling nut.


1a 801-1302 Chrome Faucet Collar $1.80 $1.70

1b 801-1302B Brass Faucet Collar $2.65 $1.95

2a 801-1306 Chrome Faucet Bonnet $1.80 $1.70

2b 801-1306B Brass Faucet Bonnet $1.80 $1.70

3 801-1308 Ball Friction Washer $.30 $.25

4 801-1310 Nylon Ball Washer $.39 $.35

5a 801-1312 Brass Lever $1.35 $1.15

5b 802-1312S Stainless Steel Lever $3.15 $2.80

6 801-1318 Coupling Gasket $.30 $.25

7a 801-1322 Chrome Shaft $3.20 $3.00

7b 801-1322B Brass Shaft $3.95 $3.75

8 801-1324 Valve Seat $.39 $.37

9 801-1326 Shaft Nut $.60 $.50

10a 801-1322ASY Chrome Shaft Assembly $3.85 $3.65

10b 801-1322BASY Brass Shaft Assembly $4.60 $4.40

10c 801-SS-1322ASY Stainless Steel Shaft Assembly $9.50 N/A

660B Series Faucets1a,b

2a,b

3

4

5a,b

6

7a,b

89

10a,b,c

Note: European facuets with US threads fit any US style shank.

808-BSEF-1C

Belgian European Style Faucet


808-BSEF-1C Chrome Belgian Faucet with Stainless Nozzle $135.95

Note: Belgian style faucet has 1/2” European shank threads. Faucet handle notincluded.

35

Faucet Replacement Parts

Perlick 525 Series Faucets


1a 810-43816 Kit w/ Plastic Shaft and Chrome Faucet Collar $11.95

1b 810-43816SS Kit w/ Stainless Shaft and Chrome Faucet Collar $13.95

1c 810-43816TF Kit w/ Plastic Shaft and TF Brass Faucet Collar $15.75

1d 810-43816SSTF Kit w/ Stainless Shaft and TF Brass Faucet Collar $20.50

2 801-1318 Coupling Gasket $.30

3 810-425-8 Lever and Spout "O" Ring (3 required) $.42

4a 810-425-3A Black Plastic Spout $4.55

4b 810-425-3TF TF Brass Spout $9.95

4c 810-425-3SS Stainless Steel Spout $6.25

5 810-425-5 Bearing Cup (2 required) $.95

6 810-307-8-2P Bonnet Washer $.45

7a 810-408-15 Chrome Faucet Bonnet $2.95

7b 810-408-15TF TF Brass Faucet Bonnet $6.95


1a 810-408A-16 Chrome Faucet Collar $3.95

1b 810-408A-16TF TF Brass Faucet Collar $7.60



3 810-425-8 Lever "O" Ring (2 required) $.42

4a 810-68157-1 Stainless Steel Lever $4.15

4b 810-67030 Push Back Creamer Lever $11.90

5 810-67382-1 Bearing Cup $1.95

6 810-43838 Seat "O" Ring $.45




1a,b

2a,b

3

4a

3

4b5

6

7

1a,b,c,d

1a,b,c,d

1a,b,c,d

1a,b,c,d

1a,b,c,d

23

3

4a4b,c

5

5

6

7a,b


1a 810-67829-1 Chrome Faucet Collar $4.25

1b 810-67829-1TF TF Brass Faucet Collar $6.95



3 810-67828-1 Bonnet Washer $.65

4 810-67819-1 Bearing Cup $1.95

5 810-68726 Stainless Steel Lever $3.95

6 810-67830-1 Lever "O" Ring $.80

7 810-67933-1 Seat "O" Ring $.30



1a,b

2a,b

3

4

5

6

7

8

36

Faucet Replacement Parts & Accessories



1 801-1301 Black Plastic Faucet Handle $1.95

2 808-0301B Black Plastic Ergo Faucet Handle $6.15

3 808-0301C Chrome Plastic Ergo Faucet Handle $14.95

4 808-1301-E Rounded Black Plastic Faucet Handle $3.25

5 808-1260XC Chrome Plated Alloy Faucet Handle $7.50


6 810-308 Faucet Lock and Key $41.95

7 810-308-KEY Key for #308 Faucet Lock $2.95

8 800-FP-100 Faucet Plug with #24R Rubber Washer $9.95

9 801-670-C 2” Chrome Faucet Extension $6.95

Note: Other faucet handles available. Custom tap handlebranding also available. Call for pricing.

1 2

6

10 12

Faucet not included 9

9 Faucet not included8a,b

7

8


8a 801-MMC-1 Chrome Bonnet Angler $8.95 $8.25

8b 801-MMB-1 Brass Bonnet Angler $8.95 $8.25No. Part Number Description 1-24 25 +

9 836-FGO-1 Faucet Guard for Standard US Faucets - 9/16" ID x 1-3/16" Long $.30 $.25

10 836-FGO-2 Faucet Guard for European and Stout Faucets - 7/16" ID x 1-11/16" Long $.35 $.30No. Part Number Description Each

11 32-KLP200 Kleen-Plug Faucet Cap and Brush (5 pack) $10.95 N/A

12 852-GF-24 Growler Filler - Double "O" Ring Attachment for US Faucets & 1-1/2' of 3/8" ID Vinyl Tubing $4.95 N/A

11


1 800-SF2000-2 Stainless Steel Screw $4.95

2 800-SF2000-3 Sliding Cap $3.25

3 800-SF2000-4 Spring $1.95

4 800-SF2000-5 Screw Cap “O” Ring $1.95

5 800-SF2000-8 Stainless Steel Piston $15.95

6 800-SF2000-9 Upper Piston "O" Ring $.99

7 800-SF2000-12 Lower Piston "O" Ring $.99

8 800-SF2000-13 Nozzle "O" Ring (2 required) $.99

9 800-SF2000-14 Stainless Steel Jet Disc $7.95

10 800-SF2000-15 Cone Flow Straightener $2.25

11 800-SF2000-16 Stainess Steel Nozzle $22.95

12 800-SF2000-17 Stainless Steel Dowel Pin $.95


14 800-SF2000-18 Stainless Steel Stop Nut $3.95

Taprite Stout Faucet

1

2

3

4

7

5

6

11

8

9

10

12

13

14

Faucet notincluded

Faucet notincluded

53 4

37

Regulators


No. Part Number Gas Gauges Description 1-11 12 +

1a 800-T742-60 CO2 60 lb. & 3000 lb. LH Stem and 5/16" Barb Shut-Off with Check Valve $45.95 $42.95

1b 800-T742-60-OR CO2 60 lb. & 3000 lb. LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $47.95 $44.95

1c 800-T742-160 CO2 160 lb. & 3000 lb. LH Stem and 5/16" Barb Shut-Off with Check Valve $49.95 $46.95

1d 800-T742-160-OR CO2 160 lb. & 3000 lb. LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $51.95 $48.95

2a 800-T741-60 CO2 60 lb. & Plugged LH Stem and 5/16" Barb Shut-Off with Check Valve $43.95 $40.95

2b 800-T741-60-OR CO2 60 lb. & Plugged LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $45.95 $42.95

2c 800-T741-160 CO2 160 lb. & Plugged LH Stem and 5/16" Barb Shut-Off with Check Valve $49.95 $44.95

2d 800-T741-160-OR CO2 160 lb. & Plugged LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $49.95 $46.95

3a 800-T742-60-2 CO2 60 lb. & 3000 lb. LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $55.95 $51.95

3b 800-T742-160-2 CO2 160 lb. & 3000 lb. LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $63.95 $59.95

4a 800-T741-60-2 CO2 60 lb. & Plugged LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $53.95 $50.95

4b 800-T741-160-2 CO2 160 lb. & Plugged LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $61.95 $58.95

5a 800-T742-60-60 CO2 2 x 60 lb. & 3000 lb. LH Stem and 2 - 5/16" Barb Shut-Offs with Check Valves $89.95 $85.95

5b 800-T742-160-160 CO2 2 x 160 lb. & 3000 lb. LH Stem and 2 - 5/16" Barb Shut-Offs with Check Valves $89.95 $85.95

6a 800-T731 CO2 2 x Plugged 12-18 PSI - LH Stem and 5/16" Barb Shut-Off with Check Valve $59.95 N/A

6b 800-T732 CO2 2 x Plugged 30-45 PSI - LH Stem and 5/16" Barb Shut-Off with Check Valve $59.95 N/A

7a 800-T742N-60 N2 60 lb. & 3000 lb. LH Nitrogen Stem with Nut and 5/16" Barb Shut-Off with Check Valve $51.95 $49.95

Taprite Primary CO2 & N2 Regulators

Note: All Regulators come with an #809-26N Nylon Washer. CO2 regulators have a polycarbonate bonnet, N2 has a steel set screw. Any regulator can have the barbed shut-off switched for a 1/4” male flare fitting or a 1/4” barbed shut-off. To switch to a 1/4” male flare fitting, addsuffix “-4MF” and subtract $2.00 from the total cost. To switch to a 1/4” barbed shut-off, add suffix “-4BF” and add $2.00 to the total cost.Please call for more information.

1a 2a

3a 4a

5a 6a 7a

38

Regulators

No. Part Number Gas Gauges Description 1-11 12 +

1a 801-710C-60 CO2 60 lb. & 3000 lb. LH Stem and 5/16" Barb Shut-Off with Check Valve $47.95 $44.95

1b 801-710C-60-OR CO2 60 lb. & 3000 lb. LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $49.95 $46.95

1c 801-710C-160 CO2 160 lb. & 3000 lb. LH Stem and 5/16" Barb Shut-Off with Check Valve $47.95 $44.95

1d 801-710C-160-OR CO2 160 lb. & 3000 lb. LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $49.95 $46.95

2a 801-709C-60 CO2 60 lb. & Plugged LH Stem and 5/16" Barb Shut-Off with Check Valve $45.95 $42.95

2b 801-709C-60-OR CO2 60 lb. & Plugged LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $47.95 $44.95

2c 801-709C-160 CO2 160 lb. & Plugged LH Stem and 5/16" Barb Shut-Off with Check Valve $45.95 $42.95

2d 801-709C-160-OR CO2 160 lb. & Plugged LH Stem with "O" Ring and 5/16" Barb Shut-Off with Check Valve $47.95 $44.95

3a 801-710C-60-2 CO2 60 lb. & 3000 lb. LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $58.95 $54.95

3b 801-710C-160-2 CO2 160 lb. & 3000 lb. LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $58.95 $54.95

4a 801-709C-60-2 CO2 60 lb. & Plugged LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $56.95 $53.95

4b 801-709C-160-2 CO2 160 lb. & Plugged LH Stem with "Y" Fitting and 2 - 5/16" Barb Shut-Offs with Check Valves $56.95 $56.95

5a 801-710C-60-60 CO2 2 x 60 lb. & 3000 lb. LH Stem and 2 - 5/16" Barb Shut-Offs with Check Valves $90.95 N/A

5b 801-710C-160-160 CO2 2 x 160 lb. & 3000 lb. LH Stem and 2 - 5/16" Barb Shut-Offs with Check Valves $90.95 N/A

6a 801-710N-60 N2 60 lb. & 3000 lb. LH Nitrogen Stem with Nut and 5/16" Barb Shut-Off with Check Valve $49.95 $46.95

6b 801-710N-160 N2 160 lb. & 3000 lb. LH Nitrogen Stem with Nut and 5/16" Barb Shut-Off with Check Valve $52.95 $49.95

Note: All regulators come with an #809-26N Nylon Washer and have a steel set screw. Any regulator can have the barbed shut-off switchedfor a 1/4” male flare fitting or a 1/4” barbed shut-off. To switch to a 1/4” male flare fitting, add suffix “-4MF” and subtract $2.00 from the totalcost. To switch to a 1/4” barbed shut-off, add suffix “-4BF” and add $2.00 to the total cost. Please call for more information.

1a 2a3a

4a5a 6a


Cornelius Primary CO2 & N2 Regulators

39

RegulatorsTaprite Secondary Regulators


800-T1661ST Single Pressure Secondary Regulator Assembly $41.95

800-T1662ST Two pressure Secondary Regulator Assembly $81.95

800-T1663ST Three Pressure Secondary Regulator Assembly $117.95

800-T1664ST Four Pressure Secondary Regulator Assembly $155.95

800-T1665ST Five Pressure Secondary Regulator Assembly $194.95

Note: All secondaries are 0-60 PSI. Secondary regulators are for use with CO2 and blended gas only. Regulators have a polycarbonate bonnet. Standard assemblies have a nipple on the inlet and a plug on the outlet. To add a nipple to the outlet sideto make assembly pass-through, add suffix “-NP” and $.50. Shut-offs may be switched to either a 1/4” male flare fitting, or a 1/4”barbed shut-off. Add suffix “-4MF” and subtract $2.00 per shut-off for a 1/4” male flare fitting. Add suffix “-4BF” and add $2.00 per shut-off for a 1/4” barbed shut-off. 160 PSI assemblies available. Please call for pricing.

800-T1661ST 800-T1662ST 800-T1663ST

800-T1661ST

Cornelius Secondary Regulators



801-C0701 Single Pressure Secondary Regulator Assembly $42.95

801-C0702 Two pressure Secondary Regulator Assembly $81.95

801-C0703 Three Pressure Secondary Regulator Assembly $120.95

801-C0704 Four Pressure Secondary Regulator Assembly $159.95

801-C0705 Five Pressure Secondary Regulator Assembly $195.95

801-C0704

801-C0701 801-C0702 801-C0703

Note: All secondaries are 0-60 PSI. Secondary regulators are for use with CO2 and blended gas only. Regulators have a steelscrew bonnet. Standard assemblies have a nipple on the inlet and a plug on the outlet. To add a nipple to the outlet side to make assembly pass-through, add suffix “-NP” and $.50. Shut-offs may be switched to either a 1/4” male flare fitting, or a 1/4” barbedshut-off. Add suffix “-4MF” and subtract $2.00 per shut-off for a 1/4” male flare fitting. Add suffix “-4BF” and add $2.00 per shut-off for a 1/4” barbed shut-off. 160 PSI assemblies available. Please call for pricing.

40

Regulator Replacement Parts & Accessories


812-719-TR 0-30 lb. RH Thread $6.50812-720-TR 0-60 lb. RH Thread $4.25812-721-TR 0-100 lb. RH Thread $6.75812-722-TR 0-160 lb. RH Thread $6.95812-724-TR 0-3000 lb. RH Thread $7.15812-725-TR 0-3000 lb. LH Thread $6.95

812-720-TR 812-725-TR


838-GP-800C Gauge Protector for Metal Bonnet Style Regulators $15.25

800-GP-742 Gauge Protector for Taprite Regulators $11.25

800-600GP Rubber Gauge Protector $2.50


1a 803-BR-MPHN-44 1/4" MPT x 1/4" Barb Nipple $1.55

1b 801-BR-MPHN-54 1/4" MPT x 5/16" Barb Nipple $1.55

1c 803-BR-MPHN-64 1/4" MPT x 3/8" Barb Nipple $1.55

2a 805-186RHL 2" RH x RH Threaded Union $2.30

2b 805-187LHL 2" LH x LH Threaded Union $6.95

3a 801-206 RH 1/4" MPT Plug $1.15

3b 801-207 LH 1/4" MPT Plug $1.50

4 801-128B "Y" Fitting w/ 2-1/4" FPT Ports and 1-1/4" MPT Inlet $5.95

5 803-CTN-180 CO2 to N2 Adapter with "O" Ring $15.95

6 819-NTC-806 N2 to CO2 Adapter with #26N Nylon washer $15.95


1 2a 3

45

89

10 11

838-GP-800C

1b 2a 3a 4

5

6Note: For other Barbed Nipple sizes, please see page 46.


1 800-112LH 2-5/8" LH Thread CO2 Stem with “O” Ring $5.65 $4.95

2a 803-110LH 2-1/4" LH Thread CO2 Stem with Threads for #ORSA-1 Assembly $3.75 $3.50

2b 803-111RH 2-1/4" RH Thread CO2 Stem with Threads for #ORSA-1 Assembly $3.95 $3.75

3 803-110LH-SH 1-1/4" LH Thread CO2 Stem (used with washers only) $3.50 $3.25

4 800-740-12N 3" LH Thread Nitrogen Stem $5.95 $5.75

5 800-118 Universal Hex Nut for CO2 Stems $3.75 $3.50

6 800-NS-2 Nitrogen Nut $5.25 $4.95

7 800-74TRQ Replacement Quad Ring $.95 $.75

8 803-ORSA-1 Screw-In "O" Ring Assembly for CO2 Stem $1.95 $1.75

9 803-ORSA-1C Replacement "O" Ring for #ORSA-1 Assembly $.95 $.75

10 809-26N Nylon CO2 Washer $.25 $.20

11 809-26 Fiber CO2 Washer $.21 $.16

12 809-RW-1 Regulator Wrench $3.25 $2.95

76

800-GP-742

800-600GP

12

41

Gas Distributor Bars & Shut-Offs


Aluminum Air Bars

Plated Brass Air Bars


800-122 2 Way Air Distributor Bar $28.95





Note: Bars come pre-assembled with 3/8” barbed brass shut-offs, 5/16” barbed nippleand a 1/4” MPT plug. Please specify desired location of nipple and plug when ordering.Plug may be substituted for an additional nipple to make air bar “pass-thru”. Pleaseadd suffix “-S” and $5.25 for a #CHW-1 safety relief valve. Bars are made of gold anodized aluminum and project shut-offs at a 45 degree angle when mounted.


801-122C 2 Way Air Distributor Bar $26.95





Note: Bars come pre-assembled with 3/8” barbed brass shut-offs, 5/16” barbed nipple anda 1/4” MPT plug. Please specify desired location of nipple and plug when ordering. Plugmay be substituted for an additional nipple to make air bar “pass-thru”. Please add suffix “-S” and $5.25 for a #CHW-1 safety relief valve. Bars come standard with 2 removable mounting brackets as shown to the left. Bars are made of chrome plated brass.

Mounting Brackets

803-CHW-1 Safety Relief Valve with lift tab

(preset to blow off at 60 PSI)

$5.25

1a 2 3 4a 5


1a 801-404 Ball Shut-Off with 3/8" Hose Barb (No Check Valve) $6.501b 801-404C Ball Shut-Off with 3/8" Hose Barb (with Check Valve) $7.152 803-404C-4 Ball Shut-Off with 1/4" Hose Barb (with Check Valve) $8.953 803-404C-4FL Ball Shut-Off with 1/4" Male Flare Outlet (with Check Valve) $8.95

4a 803-INS-404 In-Line Ball Shut-Off with 3/8" Hose Barbs (No Check Valve) $8.954b 803-INS-404-4 In-Line Ball Shut-Off with 1/4" Hose Barbs (No Check Valve) $8.955 800-1600C Brass Shut-Off with 3/8" Hose Barb (with Check Valve) $10.956 805-128T Brass Tee with 3 - 1/4" FPT Inlets $4.257 805-128X Brass Cross with 4 - 1/4" FPT Inlets $5.258 805-186RH 1-1/8" RH x RH Threaded Union $1.959 805-TEF-1 Roll of Teflon Tape - 1/2" x 520" $1.50

6 7

8

9

800-122

800-123

800-124

801-122C

801-124C

801-123C

803-CHW-1

42

Tubing

Line Size Vinyl Barrier Polyethylene Stainless Capacity (per foot)

3/16" 2.2 lb N/A 2.2 lb N/A 1/6 oz

1/4" .65 lb .30 lb .50 lb 1.2 lb 1/3 oz

5/16" .40 lb .10 lb .20 lb .30 lb 1/2 oz

3/8" .20 lb .06 lb .065 lb .12 lb 3/4 oz

1/2" 0.25 lb N/A N/A N/A 1-1/3 oz

In addition to restriction values to the left, it is necessary to add the resistance per foot of vertical

rise. For each foot of vertical rise, you must add 1/2 lb.regardless of the size of tubing being used. Optimalbeer flow is approximately 1 gallon per minute, or 2

oz. per second. Please call for more information.

Approved by all major breweries. Thermoplastic Vinyl Beverage Tubing is gauranteed non-toxic and will not affect taste or smell of beverage.Flexible and durable. Sanitary mirror finish inside and out offers outstanding resistance in harsh cleaning solutions. Vinyl tubing is NSF and

FDA approved. Approved for temperatures up to 160 Degrees F. All tubing is available for purchase by the foot, 50 ft. roll or 100 ft. roll.

Brewery Approved Vinyl Tubing

I.D. Part No. Color O.D. Length Each

3/16"

827-600 Clear 7/16" 1-49 ft. $.70827-600-50CO Clear 7/16" 50 ft. roll $24.00

827-600-100CO Clear 7/16" 100 ft. roll $38.00827-600B Black 7/16" 1-49 ft. $.75

827-600B-50CO Black 7/16" 50 ft. roll $25.00827-600B-100CO Black 7/16" 100 ft. roll $39.00

1/4"827-601 Clear 1/2" 1-49 ft. $.80

827-601-50CO Clear 1/2" 50 ft. roll $27.00827-601-100CO Clear 1/2" 100 ft. roll $40.00

5/16"

827-603 Clear 9/16" 1-49 ft. $.90827-603-50CO Clear 9/16" 50 ft. roll $30.00

827-603-100CO Clear 9/16" 100 ft. roll $46.50827-603R Red 9/16" 1-49 ft. $1.05

827-603R-50CO Red 9/16" 50 ft. roll $32.00827-603R-100CO Red 9/16" 100 ft. roll $50.00

3/8"827-602 Clear 5/8" 1-49 ft. $1.10


1/2"827-604 Clear 3/4" 1-49 ft. $1.50


5/8" 827-605 Clear 7/8" cut to order $1.65

Tubing Resistance and Capacities


1/4"805-BY-601 Clear 15/32" 1-299 ft. $.59

805-BY-601-ROLL Clear 15/32" 300 ft. Roll $.44

5/16"805-BY-603 Clear 17/32" 1-299 ft. $.69


3/8"805-BY-602 Clear 19/32" 1-299 ft. $.75


1/2"805-BY-604 Clear 21/32" 1-299 ft. $.92



1/4"

805-PY-4 White 3/8" 1-499 ft. $.26805-PY-4-ROLL White 3/8" 500 ft. Roll $.20

805-PY-4B Blue 3/8" 1-499 ft. $.26805-PY-4B-ROLL Blue 3/8" 500 ft. Roll $.20

3/8"

805-PY-3 White 1/2" 1-499 ft. $.32805-PY-3-ROLL White 1/2" 500 ft. Roll $.25

805-PY-3C* Colored 1/2" 1-499 ft. $.32805-PY-3C-ROLL* Colored 1/2" 500 ft. Roll $.25

1/2"805-PY-2 White 5/8" 1-249 ft. $.42

805-PY-2-ROLL White 5/8" 250 ft. Roll $.35

Braided Vinyl Tubing

Polyethylene Tubing

Vinyl Tubing

Braided Vinyl Tubing

Polyethylene Tubing

Note: NSF listed and FDA approved. Recommended for use where pressuresexceed 35 PSI. All sizes rated to withstand pressure up to 225 PSI. Approvedfor temperatures up to 160 Degrees F.

* Please call for available colors. Note: Colored polyethylene tubing used for glycol lines. White polyethylenetubing is NSF and FDA approved for use as product lines. Approved for temperatures up to 150 Degrees F.


43


1/4"839-FG-4R White 3/8" 1-499 ft. $.42

839-FG-4R-ROLL White 3/8” 500 ft. Roll $.31

5/16"853-FG-5R White 7/16” 1-499 ft. $.44


3/8"839-FG-3R White 1/2” 1-499 ft. $.46


Tubing & Accessories

Barrier TubingBarrier Tubing

Braided Polyethylene Tubing

Braided Barrier Tubing

Braided Barrier Tubing

Braided Polyethylene Tubing


.265"839-BY-4 White .420" 1-499 ft. $.39

839-BY-4-ROLL White .420" 500 ft. Roll $.30

.375"839-BY-6 White .535" 1-299 ft. $.44


.510"839-BY-7 White .675" 1-299 ft. $.52



1/4"839-STBB-601 White 7/16" 1-499 ft. $.44

839-STBB-601-ROLL White 7/16" 500 ft. Roll $.35

3/8"839-STBB-602 White 9/16" 1-499 ft. $.48


1/2"839-STBB-604 White 11/16" 1-499 ft. $.56



1a 801-1331* Black Plastic Hose Cutter with Blade $5.95

1b 801-1331-1 Replacement Blade for #801-1331 Hose Cutter $2.50

2 835-ID-SIZER-TOOL ID Sizer Tool for 3/16", 1/4", 5/16", 3/8", 1/2" & 3/4" Tubing $16.25

3 835-HD-1331** Heavy Duty Hose Cutter with Lock/Unlock Button $25.95

*Cuts all beverage tubing (except copper or stainless) up to a 5/8” diameter**Cuts all beverage tubing (except copper or stainless) up to a 1” diameter

1a

1b

2

3

Note: Eaton Synflex Flavor Shield Barrier tubing is NSF listed, FDA approvedand brewery approved. All sizes rated to withstand pressures up to 100 PSI.Barrier tubing is used in the construction of all trunk lines. Approved for temperatures up to 140 Degrees F.

Note: NSF listed, FDA approved and brewery approved. Suitable for soda, wine,mixed gas or straight CO2 systems. #839-BY-4 & #839-BY-6 is rated to withstandpressures up to approximately 225 PSI. #839-BY-7 is rated to withstand pressures up to 185 PSI. Approved for temperatures up to 150 Degrees F.

Note: Eaton Synflex Flavor Shield Braided Barrier tubing is NSF listed, FDA approved and brewery approved. Suitable for soda, wine, mixed gas or straightCO2systems. #839-STBB-601 & #839-STBB-602 rated to withstand pressures upto 225 PSI. #839-STBB-604 rated to withstand pressures up to 185 PSI. Approvedfor temperatures up to 150 Degrees F.



FittingsStainless Steel “T” Plastic “T”

Part Number Description Each802-SS-BUB-66S 1-1/2" W x 2-3/8" L x 3/8" Barb "U" $1.55802-SS-BUB-66M 2" W x 2" L x 3/8" Barb "U" $2.55802-SS-BUB-66L 2-3/8" W x 2-5/8" L x 3/8" Barb "U" $3.95802-SS-BUB-77 2-13/20" W x 3-3/50" L x 1/2" "U" $2.95802-SS-UY-466 1/4" x 3/8" x 3/8" "Y" $2.95802-SS-UY-666 3/8" x 3/8" x 3/8" "Y" $2.95802-SS-UY-677 3/8" x 1/2" x 1/2" "Y" $5.95802-SS-UY-777 1/2" x 1/2" x 1/2" "Y" $5.95

Stainless Steel “U” & “Y”

Stainless Steel Elbows

Part Number Description Price802-SS-BC-4444 1/4" $2.45802-SS-BC-5555 5/16" $5.95802-SS-BC-6666 3/8" $2.95802-SS-BC-7777 1/2" $7.45

Stainless Steel Cross

Stainless Steel Straight Splicers

Stainless Steel Barbed Plugs

No. Part Number Splice O.D. Size Vinyl to Barrier (I.D. to I.D.) 1-11 12 +

1 802-SS-220 3/16" x 1/4" 3/16" x 1/4" $1.65 $1.55

2 802-SS-220A 3/16" x 5/16" 3/16" x 5/16" $1.70 $1.60

3 802-SS-220B 3/16" x 3/8" 3/16" x 3/8" $1.90 $1.80

4 802-SS-220C 5/16" x 5/16" 1/4" x 5/16" $.99 $.89

5 802-SS-220D 5/16" x 3/8" 1/4" x 3/8" $1.05 $.95

6 802-SS-220E 3/8" x 3/8" 5/16" x 3/8" $1.10 $1.00

7 802-SS-220F 3/8" x 1/2" 5/16" x 1/2" $1.95 $1.85No. Part Number Splice O.D. Size Barrier to Barrier (I.D. to I.D.) 1-11 12 +

8 802-SS-220G 1/4" x 1/4" 1/4" x 1/4" $.75 $.65

9 802-SS-220H 1/4" x 5/16" 1/4" x 5/16" $.99 $.89

10 802-SS-220I 1/4" x 3/8" 1/4" x 3/8" $1.25 $1.15

11 802-SS-220J 1/4" x 1/2" 1/4" x 1/2" $2.70 $2.60

12 802-SS-220K 1/2" x 1/2" 1/2" x 1/2" $2.05 $1.95

1

2

3

4

5

6

7

8

9

10

11

12

802-SS-BT-555

802-SS-BUB-66M

805-444P

802-SS-BE-66

802-SS-UY-666

802-SS-BC-5555

802-SS-HP-6

Note: Use the outside diameter dimensions (Splice O.D. Size) to determine which splice is needed for othertubing connections not listed above. For more help, please call.


802-SS-BT-444 1/4" x 1/4" x 1/4" $1.50 $1.00

802-SS-BT-446 1/4" x 1/4" x 3/8" $1.95 $1.45

802-SS-BT-466 1/4" x 3/8" x 3/8" $1.85 $1.35

802-SS-BT-555 5/16" x 5/16" x 5/16" $2.55 $2.05

802-SS-BT-666 3/8" x 3/8" x 3/8" $1.75 $1.25

802-SS-BT-667 3/8" x 3/8" x 1/2" $6.95 $6.45

802-SS-BT-677 3/8" x 1/2" x 1/2" $2.75 $2.25

802-SS-BT-777 1/2" x 1/2" x 1/2" $2.95 $2.45


805-444P Plastic 1/4" Tee $.95

805-888P Plastic 3/8" Tee $1.25


802-SS-BE-44 1/4" x 1/4" $1.25 $1.05802-SS-BE-45 1/4" x 5/16" $3.95 $3.75802-SS-BE-46 1/4" x 3/8" $3.95 $3.75802-SS-BE-55 5/16" x 5/16" $2.95 $2.75802-SS-BE-56 5/16" x 3/8" $3.95 $3.75802-SS-BE-66 3/8" x 3/8" $1.50 $1.30802-SS-BE-67 3/8" x 1/2" $4.50 $4.30802-SS-BE-77 1/2" x 1/2" $2.75 $2.55


802-SS-HP-4 1/4" $.95 $.75802-SS-HP-5 5/16" $1.10 $.90802-SS-HP-6 3/8" $1.10 $.90802-SS-HP-7 1/2" $1.60 $1.40


Fittings

Part Number Description Each803-BR-HU-44 1/4" MF x 1/4" MPT $2.25803-BR-HU-46 1/4" MF x 3/8" MPT $3.45803-BR-HU-47 1/4" MF x 1/2" MPT $5.95803-BR-HU-64 3/8" MF x 1/4" MPT $2.95803-BR-HU-66 3/8" MF x 3/8" MPT $2.95803-BR-HU-67 3/8" MF x 1/2" MPT $6.95803-BR-HU-68 3/8" MF x 3/4" MPT $5.95803-BR-HU-74 1/2" MF x 1/4" MPT $5.95803-BR-HU-76 1/2" MF x 3/8" MPT $5.95803-BR-HU-77 1/2" MF x 1/2" MPT $5.95

Brass Male Flare x Male PipeThread Half Union

Stainless Male Flare x MalePipe Thread Half Union

Part Number Description Each803-SS-HU-44 1/4" MF x 1/4" MPT $2.05803-SS-HU-46 1/4" MF x 3/8" MPT $3.45803-SS-HU-64 3/8" MF x 1/4" MPT $3.15803-SS-HU-66 3/8" MF x 3/8" MPT $3.45803-SS-HU-67 3/8" MF x 1/2" MPT $7.95803-SS-HU-74 1/2" MF x 1/4" MPT $8.50803-SS-HU-76 1/2" MF x 3/8" MPT $8.50803-SS-HU-77 1/2" MF x 1/2" MPT $10.95


802-SS-MFU-44 1/4" MF x 1/4" MF $1.95802-SS-MFU-45 1/4" MF x 5/16" MF $1.95802-SS-MFU-55 5/16" MF x 5/16" MF $1.95802-SS-MFU-56 5/16" MF x 3/8" MF $2.95802-SS-MFU-66 3/8" MF x 3/8" MF $2.55

Stainless Male Flare x Male FlareUnion

Stainless Male Flare x Hose BarbPart Number Description Each

802-SS-MFHN-44 1/4" Barb x 1/4" MF $1.90802-SS-MFHN-45 1/4" Barb x 5/16" MF $1.95802-SS-MFHN-46 1/4" Barb x 3/8" MF $2.40802-SS-MFHN-64 3/8" Barb x 1/4" MF $1.95802-SS-MFHN-65 3/8" Barb x 5/16" MF $2.25802-SS-MFHN-66 3/8" Barb x 3/8" MF $2.75802-SS-MFHN-67 3/8" Barb x 1/2" MF $5.95802-SS-MFHN-76 1/2" Barb x 3/8" MF $4.55802-SS-MFHN-77 1/2" Barb x 1/2" MF $4.75


802-SS-MFP-4 1/4" MF Plug $1.25802-SS-MFP-5 5/16" MF Plug $1.75802-SS-MFP-6 3/8" MF Plug $1.95

Stainless Male Flare PlugStainless Female Flare Cap


802-SS-FSC-4 1/4" FF Cap $1.20802-SS-FSC-5 5/16" FF Cap $1.95802-SS-FSC-6 3/8" FF Cap $1.95

Nylon Flare WashersNickel Plated Brass Female Flare

Swivel Nuts

Stainless Swivel Hose Stems

Swivel Hose Stem & Nut Assembly

*Nylon washer not included


802-SS-FSE-44* 1/4" Barbed Elbow & 1/4" Nut $1.75



Swivel Hose Elbow & Nut Assembly

*Nylon washer not included

803-BR-HU-44

803-SS-MFU-44

802-SS-MFHN-44

802-SS-MFP-4

802-SS-FSC-5

802-NYFW-5802-NP-SN-4

802-SS-SHS-44

802-SS-SHSA-644

802-SS-FSE-44


802-NYFW-4 1/4" $.14 $.12

802-NYFW-5 5/16" $.15 $.13

802-NYFW-6 3/8" $.16 $.14

802-NYFW-7 1/2" $.45 $.42


802-NP-SN-4 1/4" Flare Nut $.49 $.46

802-NP-SN-5 5/16" Flare Nut $.70 $.60

802-NP-SN-6 3/8" Flare Nut $.75 $.72

802-NP-SN-7 1/2" Flare Nut $.95 $.92

Part Number Description Swivel Nut 1-11 12 +

802-SS-SHS-24 1/8" Barb 802-NP-SN-4 $1.20 $1.10802-SS-SHS-44 1/4" Barb 802-NP-SN-4 $.65 $.55802-SS-SHS-46 1/4" Barb 802-NP-SN-6 $1.15 $1.05802-SS-SHS-54 5/16" Barb 802-NP-SN-4 $1.55 $1.45802-SS-SHS-55 5/16" Barb 802-NP-SN-5 $1.55 $1.45802-SS-SHS-66 3/8" Barb 802-NP-SN-6 $1.15 $1.10802-SS-SHS-77 1/2" Barb 802-NP-SN-7 $1.95 $1.85


802-SS-SHSA-444* 1/4" Barb Stem & 1/4" Nut $1.95 $1.75

802-SS-SHSA-454* 5/16" Barb Stem & 1/4" Nut $2.55 $2.35

802-SS-SHSA-644* 3/8" Barb Stem & 1/4" Nut (1 pc) $2.95 $2.75

46

Fittings


803-BR-MPHN-44 1/4" Barb x 1/4" MPT $1.55803-BR-MPHN-46 1/4" Barb x 3/8" MPT $1.50803-BR-MPHN-47 1/4" Barb x 1/2" MPT $3.95801-BR-MPHN-54 5/16" Barb x 1/4" MPT $1.55803-BR-MPHN-64 3/8" Barb x 1/4" MPT $1.55803-BR-MPHN-66 3/8" Barb x 3/8" MPT $1.95803-BR-MPHN-67 3/8" Barb x 1/2" MPT $3.25803-BR-MPHN-76 1/2" Barb x 3/8" MPT $2.45803-BR-MPHN-77 1/2" Barb x 1/2" MPT $3.55


802-SS-MPHN-44 1/4" Barb x 1/4" MPT $2.95802-SS-MPHN-46 1/4" Barb x 3/8" MPT $3.95802-SS-MPHN-54 5/16" Barb x 1/4" MPT $3.95802-SS-MPHN-64 3/8" Barb x 1/4" MPT $3.15802-SS-MPHN-66 3/8" Barb x 3/8" MPT $3.95802-SS-MPHN-67 3/8" Barb x 1/2" MPT $5.75802-SS-MPHN-76 1/2" Barb x 3/8" MPT $4.95802-SS-MPHN-77 1/2" Barb x 1/2" MPT $5.95

Brass Male Pipe Thread x BarbedHose Nipple

Stainless Male Pipe Thread xBarbed Hose Nipple


801-215 Chrome Plated Brass Beer Wing Nut $2.50 $2.30

802-218 Chrome Plated Brass Beer Hex Nut $.79 $.75Part Number Description 1-99 100 +

801-24R Beer Rubber Washer $.30 $.20

Beer Nuts & Washers

Part Number I.D. O.D. Fits Vinyl Hose Fits Barrier Hose 1-24 25 +

802-216C 3/16" 1/4" 3/16" I.D. 1/4" I.D. $.75 $.70802-216B 1/4" 5/16" 1/4" I.D. 5/16" I.D. $.75 $.70802-216D 5/16" 3/8" 5/16" I.D. 3/8" I.D. $.75 $.70802-216A 3/8" 1/2" 3/8" I.D. 1/2" I.D. $.75 $.70802-216 1/2" 3/4" 1/2" I.D. N/A $.75 $.70

Part Number I.D. O.D. Fits Vinyl Hose Fits Barrier Hose 1-24 25 +802-SS-216C 3/16" 1/4" 3/16" I.D. 1/4" I.D. $2.25 $2.00802-SS-216B 1/4" 5/16" 1/4" I.D. 5/16" I.D. $2.25 $2.00802-SS-216D 5/16" 3/8" 5/16" I.D. 3/8" I.D. $2.25 $2.00802-SS-216A 3/8" 1/2" 3/8" I.D. 1/2" I.D. $2.25 $2.00802-SS-216 1/2" 3/4" 1/2" I.D. N/A $2.50 $2.25

Stainless Tailpieces

Chrome Plated Brass Tailpieces

Part Number Material Fits Vinyl Hose Fits Barrier Hose Each

801-212ALH Chrome Plated Brass 3/16" I.D. N/A $4.50801-212BLH Chrome Plated Brass 1/4" I.D. N/A $4.75801-SS-212ALH Stainless 3/16" I.D. 1/4" I.D. $5.50802-SS-212BLH Stainless 1/4" I.D. 5/16" I.D. $5.25802-SS-212DLH Stainless 5/16" I.D. 3/8" I.D. $5.25

Chrome Plated Brass & Stainless Bent Tailpieces


3/16”802-216C

1/4”802-216B

5/16”802-216D

3/8”802-216A

1/2”802-216

Part Number Material Description Each

802-216-4MF Stainless 1/4" MF x Hex Nut Tail Piece $4.25

Stainless Male Flare Tailpiece

Note: See Page 45 for swivel hose stem and nuts

3/16”802-SS-216C

1/4”802-SS-216B

5/16”802-SS-216D

3/8”802-SS-216A

1/2”802-SS-216

803-BR-MPHN-54

801-215

802-218 801-24R

802-216-4MF

801-212BLHNote: Hex nut not included with bent tailpieces

47

Fittings

Part Number Stem O.D. Each

805-JG-T333 3/16" x 3/16" x 3/16" $2.05

805-JG-T444 1/4" x 1/4" x 1/4" $2.25

805-JG-T555 5/16" x 5/16" x 5/16" $2.50

805-JG-T666 3/8" x 3/8" x 3/8" $2.95

805-JG-T777 1/2" x 1/2" x 1/2" $3.25

John Guest “T”

Part Number Stem O.D. Each

805-JG-EL33 3/16" x 3/16" $1.75

805-JG-EL44 1/4" x 1/4" $2.15

805-JG-EL55 5/16" x 5/16" $2.50

805-JG-EL66 3/8" x 3/8" $2.85

805-JG-EL77 1/2" x 1/2" $3.25

John Guest Elbow

Part Number Stem O.D. x Barb O.D. Each

805-JG-SB53 5/16" X 3/16" $1.99

805-JG-SB55 5/16" x 5/16" $1.99

805-JG-SB65 3/8" X 5/16" $1.99

805-JG-SB66 3/8" X 3/8" $1.99

805-JG-SB77 1/2" x 1/2" $3.99

805-JG-SB6P 3/8" X Plug $.99

805-JG-SB7P 1/2" x Plug $1.99

John Guest Straight Stem to Hose Barb

John Guest Straight Stem to Hose Barb Elbow

Part Number Stem O.D. x Barb O.D. Each

805-JG-S961 3/8" x 1/4" $2.25

805-JG-S965 3/8" x 5/16" $2.65


809-325014 3/8" Barb In-Line PVC Shut-Off $10.95

809-325016 1/4" Barb In-Line PVC Shut-Off $10.95

PVC In-Line Shut-Offs

Quick DisconnectsPart Number Description Each

859-HFCD-176 3/8" ID Hose Barbed Coupling Body (Liquid) $13.95

859-HFCD-226 3/8" ID Hose Barbed Coupling Insert (liquid) $13.95

859-LCD-175 5/16" ID Hose Barbed Coupling Body (Air) $19.95

859-LCD-225 5/16" ID Hose Barbed Coupling Insert (Air) $12.25

821-1187 5/16" ID Hose Barbed Quick Disconnect Body $13.95

821-1188 5/16" ID Hose Barbed Quick Disconnect Insert $5.95

859-HFCD-176 859-HFCD-225

859-LCD-175 859-LCD-226

821-1187 821-1188

809-325014

805-JG-T333

805-JG-EL33

805-JG-SB65

805-JG-S961

805-JG-SB6P


Note: Other barb sizes and style available. Call for more information.

48

Clamps

Part Number Closed-Open Fits Vinyl Fits Barrier Fits Braided Vinyl Fits Braided Barrier 1-99 100 +

Range (in.) Hose Hose Hose Hose

802-STP-100 .327 - .394 - - - - $.35 $.28

802-STP-105 .347 - .413 - 1/4" I.D. - - $.35 $.28

802-STP-113 .378 - .445 - - - 1/4" I.D. $.35 $.28

802-STP-123 .386 - .484 3/16" I.D.* 5/16" I.D. 1/4" I.D.* .265" I.D. or 1/4" I.D. $.35 $.28

802-STP-133 .425 - .524 3/16" I.D. - 1/4" I.D. - $.35 $.28

802-STP-140 .453 - .551 1/4" I.D.* 3/8" I.D. 5/16" I.D.* - $.35 $.28

802-STP-145 .472 - .571 1/4" I.D. - 5/16" I.D. 3/8" I.D. $.35 $.28

802-STP-157 .520 - .618 5/16" I.D.* - - .375" I.D. or 3/8" I.D. $.35 $.28

802-STP-162 .539 - .637 5/16" I.D.* - 3/8" I.D.* - $.35 $.28

802-STP-170 .571 - .669 5/16" I.D. or 3/8" I.D.* 1/2" I.D. 3/8" I.D. 1/2" I.D. $.35 $.28

802-STP-185 .602 - .728 3/8" I.D. - - .510" I.D. or 1/2" I.D. $.35 $.28

802-STP-198 .654 - .780 - - 1/2" I.D.* - $.35 $.28

802-STP-210 .701 - .827 1/2" I.D.* - 1/2" I.D. - $.35 $.28

802-STP-226 .763 - .889 1/2" I.D. - - - $.35 $.28

*Fits non-expanded tubing when using a fitting with the same O.D. as the tubing I.D.

Note: Use Barrier values for Polyethylene tubing; .265", .375" & .510" I.D. tubing represents Braided Polyethylene tubing.

Stainless Oetiker Stepless Clamps

Carbon Steel Oetiker Single Ear Clamps

Part Number Fits Vinyl Hose (I.D.) 1-99 100 +

828-WD-5 3/16", 1/4", 5/16" $.69 $.49828-WD-10 3/8", 1/2", 5/8" $.69 $.49

Part Number Fits Vinyl Hose 1-99 100 +840-123-1 3/16" I.D.* $.36 $.30840-133-1 3/16" I.D. $.36 $.30840-145-1 1/4" I.D. $.36 $.30840-157-1 5/16" I.D.* $.36 $.30840-165-1 5/16" I.D. $.40 $.35840-170-1 3/8" I.D.* $.36 $.30840-185-1 3/8" I.D. $.36 $.30840-226-1 1/2" I.D. $.36 $.30

Part Number Fits Vinyl Hose 1-99 100 +

840-561113 3/16" I.D. $.50 $.40840-561315 1/4" I.D. $.50 $.40840-561517 5/16" I.D. $.50 $.40840-561518 3/8" I.D. $.50 $.40840-561720 1/2" I.D. $.50 $.40

Part Number Fits Vinyl Hose 1-99 100 +828-1505 3/16" I.D. $.25 $.20828-1680 5/16" I.D. $.25 $.20

Carbon Steel Oetiker Double Ear Clamps

Stainless Worm Drive Clamps

Plastic Pinch Clamps

Stainless Back Welded Single Ear Clamps

Part Number Fits Vinyl Hose 1-99 100 +

805-P6 3/16" I.D. $.30 $.25805-P8 1/4" I.D. $.30 $.25805-P10 5/16" I.D. $.35 $.30805-P12 3/8" I.D. $.35 $.30


802-2400 Side Jaw Crimpers $19.95802-2401 Straight Jaw Crimpers $16.95

Crimping Tools


Double Ear ClampWorm Drive Clamp

Pinch Clamp

Carbon Steel SingleEar Clamp

Back Welded SingleEar Clamp

802-2400

802-2401

*Fits non-expanded tubing when using a fitting with the same O.D.

as the tubing I.D.


Secondary Wall PanelsGalvanized Steel Panels


800-GV-712 7" x 11" Panel $12.95

800-GV-718 7" x 16" Panel $13.95

800-GV-724 7" x 21" Panel $14.95

817-GV-1212 12" x 12" Panel $18.95

817-GV-1218 12" x 18" Panel $19.95

817-GV-1224 12" x 24" Panel $20.95

Note: All panels have a 3/4” raised surface and pre-drilled mountingholes.


852-1621 2 Product Secondary Wall Panel with Brackets Only $99.95




Secondary Regulator Panel with Brackets

Note: All Panels come standard with Taprite 0-60 PSI secondary regulators, 803-SS-271 wall brackets and galvanized steel panel. Cornelius 0-60 PSI secondaryregulators may be used upon request. Add $4.00 per secondary regulator for Cornelius secondaries. All secondary regulator assemblies come standard as plugleft, nipple right. Please specify location of plug and nipple or if panel is to be pass-thru.

Secondary Regulator Panel with Brackets, Tubing& Fittings


852-16215 2 Product Secondary Wall Panel Assembly $155.95




Secondary Regulator Panel with Brackets, Tubing,Fittings and F.O.B’s

Note: All panels come standard with Taprite 0-60 PSI secondary regulators, 803-SS-271 wall brackets, 7 ft. of 5/16” red vinyl tubing, 7 ft. of 3/8” clear vinyl tubing, 3/8”stainless steel nipples, hex nuts, rubber washers, wing nuts and clamps. Cornelius0-60 PSI secondary regulators may be used upon request. Add $4.00 per secondaryregulator for Cornelius secondaries. All secondary regulator assemblies comestandard as plug left, nipple right. Please specify location of plug and nipple or ifpanel is to be pass-thru. Longer jumpers may be substituted at an additionalcharge. Please specify when ordering.

Part Number Description Each U-Bend

852-16215-FB 2 Product Secondary Wall Panel Assembly with FOB's $255.00 $265.00




Note: All panels come standard with Taprite 0-60 PSI secondary regulators, 806-TECFLO-5HV F.O.B’s, 7 ft. of 5/16” red vinyl tubing, 7 ft. of 3/8” clear vinyl tubing, 3/8”stainless steel nipples, rubber washers, wing nuts and clamps. Panels may be builtwith optional 802-4132 S/S 3/8” push-in “U” bends (not shown). Cornelius 0-60 PSI secondary regulators may be used upon request. Add $4.00 per secondary regulator forCornelius secondaries. All secondary regulator assemblies come standard as plug left,nipple right. Please specify location of plug and nipple or if panel is to be pass-thru.Longer jumpers may be substituted at an additional charge. Please specify when ordering. F.O.B’s may be substituted for other brands upon request. See page 51 for allF.O.B’s and F.O.B accessories. Call for pricing for substituting F.O.B’s.

800-GV-724

852-1631

852-16315

852-16415-FB

50


852-16215-FOB-BP 2 Product Secondary Wall Panel Assembly with FOB's and Flojet Beer Pumps $415.00

All panels come standard with one Taprite 0-60 PSI and one 0-100 PSI secondary regulator, #806-TECFLO-5HVF.O.B’s, Flojet beer pumps, #803-SS-271 wall brackets, high pressure braided vinyl tubing from regulator topumps, Barrier tubing from pumps to F.O.B’s and F.O.B’s to wall brackets, 7 ft. of 5/16” red vinyl tubing, 7 ft.of 3/8” clear vinyl tubing, pump exhaust line with John Guest fittings, 3/8” stainless steel nipples, hex nuts,rubber washers, wing nuts, clamps and stainless elbows. All secondary regulator assemblies come standardas plug left, nipple right. Please specify location of plug and nipple or if panel is to be pass-thru. Longerjumpers may be substituted at an additional charge. Please specify when ordering. F.O.B’s may be substituted for other brands upon request. Please see page 51 for all F.O.B’s. Call for pricing for substitutingF.O.B’s. Flojet Pumps may be installed with reverse flow valves upon request. Please call for pricing and moreinformation.

Secondary Regulator Panel with Brackets, Tubing,Fittings, F.O.B’s & Beer Pumps

Flooded Beer Manifolds

Secondary Wall Panels, Beer Pumps & Beer Manifolds


803-FBMSS Stainless Steel Flooded Beer Manifold Call for Pricing

803-FBMSSwith 3/8” Barbed Inlet

and Outlets

Note: All flooded manifolds are built to customer specification. Please specifynumber of products, orientation of manifold; vertical or horizontal, and desiredlocation of inlets and outlets. Manifolds may be ordered with 1/4” - 1/2” barbs,standard beer thread or 1/4” male flare inlets and outlets. Please specify whenordering. Allow 3-4 business days for fabrication.



809-FBP-1 Flojet Beer Pump $68.50 $59.50

Flojet Beer Pump

Comes standard with two combination 3/8” - 1/2” barbed inlet andoutlet nipples, 1/4” barbed gas inlet nipple and 1/4” barbed gas outlet.

3-1/4” W x 4-3/4” D x 6” H


809-FBPRV-1 Flojet Beer Pump Reverse Flow Valve $23.95

Flojet Beer Pump Reverse Flow Valve

Flojet Beer Pump Replacement Fittings


809-FBF-S62Set of Two Combination 3/8" - 1/2" Barbed Inlet &

Outlet Nipples for Flojet Beer Pumps$2.95

809-FBF-EB62Set of Two Combination 3/8" - 1/2" Barbed Elbow

Inlet & Outlet Nipples for Flojet Beer Pumps$3.25

Beer Pump & F.O.B Facts

· Pumps may drive beer up to 600 ft. from keg to faucet.

· Secondary Regulators maintain proper CO2 level in kegs .

· Beer pumps must be installed within 15 ft. of kegs.

· Beer pumps capable of delivering beer vertically up to 100 feet in a single line.

· Beer pumps help maintain the brewers recommended applied pressure on the beer over short, long, horizontal or vertical runs.

· Important: Gas exhaust from beer pumps must be vented from walk-in cooler to a well ventilated area outside the walk-in cooler.

· F.O.B's shut-off pump and will cut the beer flow as soon as foam is detected from an empty keg.

· F.O.B's installed in a draft beer system will reduce beer waste and increase beer profits by keeping the beer lines full instead of filling with foam.

· Keeping lines full of beer eliminates the need to refill the lines and purge the system with beer when tapping a new keg, thus reducing beer waste.

809-FBP-1

809-FBF-S62809-FBF-EB62

809-FBPRV-1

Note: Brass exhaust fittings also available. Call for pricing.

51

Foam on Beer Detectors, Drain Line & Wall Brackets



806-TECFLO-5HV TECFLO F.O.B with 3/8" Barbed John Guest Inlet/Outlet and 3/8" O.D. Drain Port $51.95 $49.95

806-TECFLO-1 TECFLO F.O.B with 3/8" Barbed John Guest Inlet/Outlet and 3/16" O.D. Drain Port $51.95 $49.95

846-DFC-9500 Pacific F.O.B with Male Beer Thread Inlet/Outlet and 5/16" O.D. Drain Port $49.95 $47.95

809-TRUPOUR-66 Trupour Stainless Steel and Glass F.O.B with 3/8" Barbed Inlet/Outlet and 9/32" O.D. Drain Port $115.95 $112.95

Part Number Decription Each802-4132 3/8” Barb S/S F.O.B Push-In “U” Bend $3.60801-131 3/8" Bore Beer Switch with Shut-Offs $58.50801-132 3/8" Bore Beer "Y" $16.50801-133 3/8" Bore Beer "Y" Bracket $19.95801-760 Single Beer Shut-off $18.50810-FT-872L Male Beer Thread to Beer Hex Nut Elbow $12.75802-SS-271 3/8" Bore Stainless Steel Wall Bracket $7.95802-SS-271-66 3/8" Barbed Elbow Stainless Steel Wall Bracket $4.95803-SS-133-666 3/8" Barbed "Y" Stainless Steel Wall Bracket $8.95

806-TECFLO-5HV 806-TECFLO-1

805-CLDL-14-16

805-PY-316

801-131

801-133

810-FT-872L

801-760801-132

802-SS-271 802-SS-271-66 802-SS-133-666

846-DFC-9500809-TRUPOUR-66

F.O.B Drain Line & Drain Bottle Kit

Foam on Beer Detectors (F.O.B)

Wall Brackets & Fittings

805-CLDL-14-16 fits TECFLO-5HV, DFC-9500 and TRUPOUR-66 F.O.B’s. 805-PY-316 fits TECFLO-1F.O.B’s. For Tee and Elbow fittings, see page 44. For John Guest Fittings, see page 47.


805-CLDL-14-16 1/4" I.D. x 3/8" O.D. x 1/16" Wall Clear Polyvinyl F.O.B Drain Line $.25805-PY-316 1/8" I.D. x 3/16" O.D. x 1/16" Wall White Polyethylene F.O.B Drain Line $.17852-FOBDK-1 1 Qt. F.O.B Drain Bottle & Mounting Bracket (Includes Mounting Hardware) $5.95

852-FOBDK-1

802-4132

52

Gas Blenders, Wall Mount Regulators & Gas Fittings

#TM100 can produce up to 15 kegs per hour dispensed. #TM200 can produce up to 30 kegs per hour (15 kegs per hour per blend) dispensed.#TM300 can produce up to 30 kegs per hour dispensed. #TM100 & #TM200 can be set to a minimum inlet pressure of 45 psi, 55 psi, 70 psi or110 psi. Standard inlet pressures for the #TM100 & #TM200 are 55 psi or 70 psi. Please specify desired inlet pressure when ordering. #TM300can be set to a minimum inlet pressure of 45 psi or 55 psi only. The #TM100 & #TM200 have adjustable outlet pressures of 0-60 psi. Pleasenote that the maximum outlet pressure will always be 10 psi lower than the lowest inlet pressure. The #TM300 has an outlet pressure of 8 psiless than the inlet pressure (45 psi or 55 psi) and requires a secondary regulator before the keg. All McDantim gas blenders maintain accu-racy of +/- 2% of full scale or better within a flow range of .4 to 40 liters per minute (.85 to 85 cubic feet per hour). All panels come standardwith 1/4” female NPT fittings. Panels may be ordered with 1/4”, 5/16” or 3/8” barbed fittings. Blenders may be ordered to any blend in incre-ments of 5%. Please specify when ordering. Common blends are listed below. All McDantim gas blenders come with a limited 5 Year Warranty.

IMPORTANT: Please note that yourincoming pressure must be at orabove your panels precalibrated inletpressure. Example: If you order yourblender with a 55 psi minimum inletpressure, then you must provide atleast 55 psi or greater to the blenderpanel.

WARNING: There are inherent dangers with any compressed gassystem. Use of a professional installer is strongly suggested.

NOTE: McDantim gas blenders arenot recommended for use withcompressed air and should be usedwith Carbon Dioxide and Nitrogenonly. TM100 Series TM200 Series TM300 Series

McDantim CO2 & N2 Gas Blenders


811-TM100-25C Single Blend: 25% CO2, 75% N2 $530.00




811-TM200-60C-25C Double Blend: 60% CO2, 40% N2 and 25% CO2, 75% N2 $775.00



811-TM300-75C-60C-25C Triple Blend: 75% CO2, 25% N2 and 60% CO2, 40% N2 and 25% CO2, 75% N2 $855.00

811-TM300-70C-65C-25C Triple Blend: 70% CO2, 30% N2 and 65% CO2, 35% N2 and 25% CO2, 75% N2 $855.00


800-742WMHP-C6 Wall Mounted Taprite T742-160 CO2 Regulator with 6 ft. of High Pressure Hose $93.95

800-742WMHP-N6 Wall Mounted Taprite T742N-160 N2 Regulator with 6 ft. of High Pressure Hose $98.95

800-7000-6A-C 6 ft. of High Pressure Hose with 1/4" FPT Fitting and CO2 Stem & Nut $39.95

800-7000-6A-N 6 ft. of High Pressure Hose with 1/4" FPT Fitting and N2 Stem & Nut $44.95



811-MV013 1/4" Barbed Tee with Check Valve $22.95811-MV042 3/8" Barbed Tee with Check Valve $22.95811-MV044 1/4" x 1/4" x 3/8" Barbed Tee with Check Valve $22.95811-MV045 1/4" x 3/8" x 3/8" Barbed Tee with Check Valve $22.95803-NS-764 3/8" Barbed Inline Check Valve $6.95

Barbed Fittings with Check Valves

Wall Mount High Pressure Regulators

811-MV045

803-NS-764

800-742WMHP-N6 800-742WMHP-C6

800-7000-6A-C

53

Gas Switchover Kits & Leak Detectors



857-2TASK-C 2 Tank CO2 Automatic Switchover $435.00857-2TASK-N 2 Tank N2 Automatic Switchover $435.00857-4TASK-C 4 Tank CO2 Automatic Switchover $545.00857-4TASK-N 4 Tank N2 Automatic Switchover $545.00857-6TASK-C 6 Tank CO2 Automatic Switchover $615.00857-6TASK-N 6 Tank N2 Automatic Switchover $615.00857-8TASK-C 8 Tank CO2 Automatic Switchover $685.00857-8TASK-N 8 Tank N2 Automatic Switchover $685.00

Automatic CO2 & N2 Switchover Kits

Manual CO2 & N2 Switchover Kit

Beer System Leak Detector

When tank or tanks feeding one side of the switchover fall below 200 psi, the boxwill automatically changeover to a full tank eliminating the need for manuallychanging tanks. Switchover kits are non-electric and come standard with a 20 yearwarranty. Kits are approved to work with mixed gas tanks.

Note: All switchover kits come standard withone 0-3000 psi gauge per tank, high pressurehose with either Nitrogen or CO2 adaptersthat connect to each tank and CO2 or N2threads for CO2 or N2 primary regulators.Primary regulators not included.


803-7430-KIT 2 Tank CO2 or N2 Manual Switchover Kit $25.95

Note: Manual switchover kits may be used with two separate tanks of CO2 orN2 with primary regulators and can be hooked up to either side of theswitchover valve to allow for quick and easy changeover from an empty to fulltank. Valves come standard with 1/4”, 5/16” or 3/8” barbed swivel hose stemsand 1/4” swivel hose nuts. Please specify desired barb size when ordering.


811-MV039 Single Inline Leak Detector $87.95

811-MV035 Double Inline Leak Detector $99.95

The inline leak indicator can tell you in seconds if you have leaks in yourbeer system and how big those leaks are no matter what gas source isbeing used or how complicated the system is. The leak indicator can bespliced in before or after a gas blender and can be permanently installedor removed at any time. All leak detectors come standard with 3/8”barbed nipples. 1/4” and 5/16” barbed nipples available. Please specifywhen ordering.


800-BCT-100 Beer Carbonation Test Kit $282.95

Checks carbonation test levels. Easy to use, easy toclean. Comes standard with all stainless steel andplated metal fittings and a plastic carrying case withtubing and instructions.


811-BCWA-100 Beer Check with Adapter Kit $950.00811-BCWALS-100 Beer Check with Adapter Kit and Leak Sensing Wand $1,195.00811-LSW-100 Leak Sensing Wand Only Call858-4180-53 8 oz. Liquid Gas Leak Dector with Dauber Applicator $8.50

Note: Leak Sensing Wand must be used with a Beer Check Analyzer and can measure leaking gas by sensing motion as small as 0.2 cubic feet per hour. Beer Check with male beer thread adapter measures the amount of CO2 in N2 or CO2in O2 to an accuracy of 1%. Can also measure O2 in N2 to an accuracy of 0.5%. BeerCheck comes with a 9V battery.

Gas Leak & Measuring Devices

Beer Carbonation Test Kit

857-2TASK-C

803-7430-KIT

811-MV039 811-MV035

811-BCWA-100 858-4180-53811-BCWALS-100

54

Gas Tanks & Replacement Parts

Part Number Description Yield (1/2 Kegs) O.D. Height 1-9 10 +

830-4CO2RS 4 lb. CO2 Tank (Reconditioned Steel) 4-6 4-1/2" 21-3/4" $52.50 $49.50

830-5CO2RS 5 lb. CO2 Tank (Reconditioned Steel) 6-8 5-1/2" 18" $54.50 $51.50

830-5CO2NS 5 lb. CO2 Tank (New Steel) 6-8 5-1/2" 18" $71.50 $66.50

830-5CO2RA 5 lb. CO2 Tank (Reconditioned Aluminum) 6-8 5" 19-1/2" $60.50 $57.50


830-10CO2RA 10 lb. CO2 Tank (Reconditioned Aluminum) 13-18 6-1/2" 23-3/4" $69.00 $64.00





830-50CO2RS 50 lb. CO2 Tank (Reconditioned Steel) 80-85 9" 55" $195.00 $175.00

830-5CO2RA

830-20NC-580NS

Part Number Description Yield (1/2 Kegs) O.D. Height Each

830-20NC-580NS 20 Cubic ft. Mixed Gas Tank (New Steel) 3-4 5-1/4" 18" $105.95

830-20NC-580RS 20 Cubic ft. Mixed Gas Tank (Reconditioned Steel) 3-4 5-1/4" 18" $79.95

830-60NC-580NS 60 Cubic ft. Mixed Gas Tank (New Steel) 7-10 6-3/4" 27-1/4" $189.00

830-60NC-580RS 60 Cubic ft. Mixed Gas Tank (Reconditioned Steel) 7-10 6-3/4" 29-1/2" $140.00

830-228NC-580RS 228 Cubic ft. Mixed Gas Tank (Reconditioned Steel) 28-32 9" 55" Call

All reconditioned tanks have undergone hydrostatic testing and are certified for 5 years from the date of testing. All CO2tanks have a new CGA 320 valve and are repainted. Some cosmetic imperfections are possible. All tanks ship empty.Most 20 lb. tanks include a black carry handle. 50 lb. steel tanks include a metal neck ring and cap. It is recommendedthat all tanks be used standing upright and secured with a holding strap. See below for wall mount tank holders.

CO2 Tanks

N2 Tanks

Note: All reconditioned tanks have undergone hydrostatic testing and are certified for 5 years from the date of testing.830-228NC-580RS tank includes a metal neck and ring cap. Siphon down tubes may be special ordered at a differentlength for new tanks. All tanks come with a new CGA 580 valve and are repainted. 830-20NC-580NS, 830-20NC-580RS,830-60NC-580NS & 830-228NC-590RS have a service rating of 2015 psi. 830-60NC-580RS has a service rating of 1800psi. Both the size (cubic foot capacity) and service rating determine the volume of gas that can be compressed in atank, unlike CO2 where the tank capacity is measured in pounds.


835-WMCB-1 1 Tank Wall Mounted Cylinder Bracket $44.95



Note: All cylinder brackets are constructed of steel and have steelcinch buckles. All brackets fit tanks between 4” and 12” in diameter. Brackets are 3-7/8” Dand 2-3/8” H. 835-WMCB-1 is 8” W,830-WMCB-2 is 24” W & 830-WMCB-3 is 35-5/8” W. Mounting Hard-ware not included.


830-P1100X15 Metal Replacement Handwheel for Valves $4.50

830-CSAFETY-MT Male Thread 3000 PSI CO2 Valve Safety $4.95

830-CSAFETY-FT Female Thread 3000 PSI CO2 Valve Safety $4.95

852-BOK-1 Blow Out Kit with Valve Fitting, Swivel Stem & Nut, and Tubing $8.50

CO2 Valve NOT Included

Replacement Valve Parts

852-BOK-1

830-CSAFETY-FT830-CSAFETY-MT830-P1100X15

835-WMCB-1 835-WMCB-2

835-WMCB-3

Wall Mount Tank Holders


55

Trunk Lines & Glycol Feed Lines


Factory Made Trunk Lines

Insulation3/4” Wall

Insulation3/4” Wall

Color Coded ProductLines

1/4”, 5/16” or 3/8” I.D

Flavorshield Barrier

Color Coded ProductLines

1/4”, 5/16” or 3/8” I.D

Flavorshield Barrier

Glycol Supply & ReturnLines

3/8” I.D Colored Polyethylene

Tubing

Glycol Supply &Return Lines

3/8” I.D Colored

Polyethylene Tubing

Moisture Barrier WrapPrevents condensation from

compromising insulation

Moisture Barrier WrapPrevents condensation from

compromising insulation

Foil WrapConducts cold transfer

from glycol lines to

product lines

Foil WrapConducts cold transfer

from glycol lines to

product lines

Vinyl Tape JacketExtruded PVC Jacket

Part Number Barrier I.D. Product Lines Glycol Lines Taped Jacket PVC Jacket808-5TL-2-2 5/16" 2 2 $6.95 N/A808-5TL-2-4 5/16" 4 2 $7.25 $8.95808-5TL-2-6 5/16" 6 2 $7.95 $9.95808-5TL-2-8 5/16" 8 2 $8.95 $11.50808-5TL-4-10 5/16" 10 4 $10.95 $13.50808-5TL-4-12 5/16" 12 4 $11.95 $13.95808-5TL-4-14 5/16" 14 4 $12.95 $14.75

Part Number Barrier I.D. Product Lines Glycol Lines Taped Jacket PVC Jacket808-6TL-2-2 3/8" 2 2 $8.25 N/A808-6TL-2-4 3/8" 4 2 $7.50 $8.95808-6TL-2-6 3/8" 6 2 $8.50 $9.95808-6TL-2-8 3/8" 8 2 $9.50 $11.50808-6TL-4-10 3/8" 10 4 $11.50 $13.95808-6TL-4-12 3/8" 12 4 $12.50 $14.50808-6TL-4-14 3/8" 14 4 $13.50 $15.25

1/4” Trunk Line

.30 lbs. Restriction perFoot

1/3 oz. Beer per Foot

5/16” Trunk Line



3/8” Trunk Line



Note: All trunk lines have 3/4” wall closed cell insulation. Most variations typically ship within 1-2 business days. Custom trunk lines can bebuilt upon request with any number of lines up to 16 products (all I.D sizes) and 75 ft. in total length. Trunk lines can be custom built withwine lines or a combination of wine and beer lines within a single bundle. Custom built trunk lines with 1/2” I.D. polyethylene glycol lines alsoavailable. Please allow 3-5 days for custom built trunk lines. Call for pricing and more information.

Most trunk lines must ship via freight carrier from the manufacturer starting at $110.00 depending on size, ship to location, and any shippingextras required for delivery. Some trunk lines may ship via UPS depending on number of lines and length. Please call for a shipping quote.

Glycol feed lines are built with 3/4” wall closed cell insulation, color coded polyethylene glycol lines, foil wrap, moisture barrier wrap & tapedjacket. Feed lines can be built with 1/2” I.D. polyethylene tubing upon request. Please call for pricing.

Part Number Barrier I.D. Product Lines Glycol Lines Taped Jacket PVC Jacket810-4TL-2-2 1/4" 2 2 $8.95 N/A806-4TL-2-4 1/4" 4 2 $9.50 $8.95806-4TL-2-6 1/4" 6 2 $10.95 $9.95806-4TL-2-8 1/4" 8 2 $11.95 $11.50806-4TL-4-10 1/4" 10 4 $13.95 $13.50806-4TL-4-12 1/4" 12 4 $15.50 $14.50

Part Number Polyethylene I.D. Glycol Lines Each852-GFL-2 3/8" 2 $5.95852-GFL-4 3/8" 4 $6.95

Glycol Feed Lines

56

UBC Glycol Power Packs

Max Distance, ft. 25' 125' 125'Part Number 806-UBC-25-1VP-LP 806-UBC-125-1PP-TV 806-UBC-125-1PP-LP

Each $665.00 $1,095.00 $1,095.00

Compressor Size 1/6 HP 3/8 HP 3/8 HP

Bath Capacity 2 Gallons 7 Gallons 5 Gallons

Pump Type Vertical 100 GPH 100 GPH

BTU/Hour 1150 2690 2690

Thermostat Digital Digital Digital

Refrigerant R-134a R-134a R-134a

Dimensions 17" W x 19" D x 17" H 15" W x 18" D x 28" H 28" W x 19" D x 19" H

Weight 42 lbs. 96 lbs. 95 lbs.


Max Distance, ft. 250' 450'Part Number 806-UBC-250-1PP-TV 806-UBC-250-2PP-TV 806-UBC-450-1PP-TV 806-UBC-450-2PP-TV

Pump Type 100 GPH Dual 100 GPH 100 GPH Dual 100 GPH

Each $1,365.00 $1,615.00 $1,745.00 $1,995.00

Compressor Size 1/2 HP 3/4 HP

Bath Capacity 18 Gallons 18 Gallons

BTU/Hour 3900 5500

Thermostat Digital Digital

Refrigerant R-134a R-134a

Dimensions 24" W x 28" D x 30" H 30" W x 28" D x 30" H 24" W x 28" D x 30" H 30" W x 28" D x 30" H

Weight 155 lbs. 168 lbs. 161 lbs. 174 lbs.

Note: 1/6 HP and 1/3 HP units must be ran on a dedicated 15 amp circuit. It is strongly recommended that an electrician ensures unit is on itsown dedicated circuit. All units must be properly cleaned and maintained. Failure to do so could void warranty. Units should be elevated atleast 6” from the ground. 1/3 HP units come standard with 6” legs. All units are 115V/60HZ/1P and include a 6’ plug and chord. Please notethat all glycol concentrate should be mixed with distilled water. See below for warranty information.

Note: 1/2 HP and 3/4 HP units must be ran on a dedicated 20 amp circuit. If a second pump and motor is being ran, the additional pump andmotor must also be on its own dedicated 15 amp circuit. It is strongly recommended that an electrician ensures unit is on its own dedicatedcircuit. All units must be properly cleaned and maintained. Failure to do so could void warranty. Units should be elevated at least 6” from theground. 1/2 HP and 3/4 HP units come standard with 6” legs. All units are 115V/60HZ/1P and include a 6’ plug and chord. Please note that allglycol concentrate should be mixed with distilled water.

Warranty: UBC Group offers a 1 year parts & labor, 5 year compressor warranty on all units. Please note that Rochester Store Fixture will pro-vide a warranty claim form in the event of any warranty work needed, however, warranty claims should be filed with UBC Group directly.

806-UBC-250-1PP-TV

806-UBC-25-1VP-LV806-UBC-125-1PP-TV

806-UBC-125-1PP-LV

806-UBC-450-1PP-TV

57

Vin Service Glycol Power Packs


Max Distance, ft. 35' 75’Part Number 808-VS-35-1VP 808-VS-75-1VP

Each $805.00 $1,180.00

Pump Type Vertical Vertical


Bath Capacity 3.2 Gallons 4.5 Gallons

BTU/Hour 936 1297



Dimensions 17” W x 18” D x 14” H 25” W x 17” D x 16” H

Weight 80 lbs. 130 lbs.

Note: 1/3 HP units must be ran on a dedicated 15 amp circuit. If a second pump and motor is being ran, the additional pump and motor mustalso be on its own dedicated 15 amp circuit. 1/2 HP units must be ran on a dedicated 20 amp circuit. If a second pump and motor is being ran,the additional pump and motor must also be on its own dedicated 20 amp circuit. It is strongly recommended that an electrician ensures unitis on its own dedicated circuit. All units must be properly cleaned and maintained. Failure to do so could void warranty. Units should be ele-vated at least 6” from the ground. All units are 115V/60HZ/1P and include a 6’ plug and chord. Please note that all glycol concentrate shouldbe mixed with distilled water.Warranty: Vin Service offers a 1 year parts & labor, 5 year compressor warranty on all units. Please note that Rochester Store Fixture will pro-vide a warranty claim form in the event of any warranty work needed, however, warranty claims should be filed with Vin Service/CBS directly.

Note: 1/6 HP and 1/3 HP units must be ran on a dedicated 15 amp circuit. It is strongly recommended that an electrician ensures unit is on itsown dedicated circuit. All units must be properly cleaned and maintained. Failure to do so could void warranty. Units should be elevated atleast 6” from the ground. All units are 115V/60HZ/1P and include a 6’ plug and chord. Please note that all glycol concentrate should be mixedwith distilled water. See below for warranty information.

808-VS-250-2PP

808-VS-30-1VP 808-VS-75-1VP

Max Distance, ft. 125' 250'Part Number 808-VS-125-1PP 808-VS-125-2PP 808-VS-250-1PP 808-VS-250-2PP

Pump Type 75 GPH Dual 75 GPH 75 GPH Dual 75 GPH

Each $1,595.00 $1,925.00 $1,850.00 $2,155.00


Bath Capacity 13.2 Gallons 13.2 Gallons

BTU/Hour 3568 7030



Dimensions 18" W x 18" D x 29" H 24" W x 18" D x 29" H 18" W x 18" D x 29" H 24" W x 18" D x 29" H

Weight 205 lbs. 220 lbs. 210 lbs. 225 lbs.

808-VS-125-1PP

58

Glycol Components, Glycol Solution, Tapes & Insulation


Part Number Description 1-4 5 +806-PS-1 1 Gallon UBC Glycol Concentrate $26.50 $24.50806-PS-5 5 Gallon UBC Glycol Concentrate $115.00 N/A810-63299-1 1 Gallon Perlick Premixed Glycol Solution $24.50 $22.50

Part Number Description Each806-XR02CX* Dixell Digital Thermostat for UBC Power Packs $59.95806-AKO13120** AKO Digital Thermostat for UBC Power Packs $59.95844-GLYRFT-100 Glycol Hydrometer $44.95

Note: It is recommended that glycol concentrate be mixed with distilled water. Typical mixture for UBC solution is 2 parts water to 1 part glycol concentrate.Perlick glycol comes premixed, 2 parts water to 1 part glycol solution.

* Dixell digital thermostats are for use with all UBC power packs manufactured from 2010 topresent. ** AKO digital thermostats are for use with 1/6 HP & 1/3 HP UBC power packs manufacturedbefore Fall of 2010.Note: Vin Service replacement thermostats also available for all models. Call for pricing.

Part Number Description Each852-GPA-PA301 Glycol Pump & Motor Assembly with 105 GPH Pump $267.25852-GPA-PA201 Glycol Pump & Motor Assembly with 70 GPH Pump $267.25845-315183-13 1/3 HP Motor Only $127.95845-PA301 105 GPH Rotary Vane Clamp-On Pump $95.95845-PA201 70 GPH Rotary Vane Clamp-On Pump $95.95845-2W685 8 ft. Power Supply Cord $12.95845-SYPC-1 Styrofoam Pump Cover $4.95845-RVPM-HUB Nylon Pump Saver & V-Clamp Assembly $11.50845-RVPM-MH Nylon Pump Saver Misallignment Hub Only $6.00845-RVPM-RG Nylon Pump Saver Ring Only $4.25845-187483 V-Clamp with Bolt $2.95803-BR-MPHN-66 3/8" Barb x 3/8" MPT Hose Nipple $1.95803-BR-MPHN-76 1/2" Barb x 3/8" MPT Hose Nipple $2.45

Part Number Description Each816-343078 7/8" I.D. x 3/4" Wall $2.25816-343118 1-1/8" I.D. x 3/4" Wall $2.35816-343138 1-3/8" I.D. x 3/4" Wall $2.75816-343158 1-5/8" I.D. x 3/4" Wall $3.25816-343178 1-7/8" I.D. x 3/4" Wall $3.50816-346218 2-1/8" I.D. x 3/4" Wall $3.75816-343238 2-3/8" I.D. x 3/4" Wall $3.95816-343258 2-5/8" I.D. x 3/4" Wall $4.35816-3X4-4 3' x 4' x 1/4" Flat Sheet $19.95842-SPRAY-FOAM 16 oz. Can of Spray Insulation $6.95

Glycol Solution

Replacement Thermostats & Hydrometers

Glycol Pump & Motor Components

Insulation

TapesPart Number Description Each

816-ALDT-3150 3" x 150 ft. Roll of Aluminum Foil Tape $14.95816-ALDT-4150 4" x 150 ft. Roll of Aluminum Foil Tape $16.95816-ET-236 2" x 108 ft. Roll of Black Vinyl Tape $8.95835-DT-1075 2" x 180 ft. Roll of Black Waterproof Duct Tape $11.95835-ET-7520 3/4" x 60 ft. Roll of Black Vinyl Electrical Tape $1.75861-2A659 330 ft. Roll of Clear Vapor Barrier Tape $2.95835-FIT-30 2" x 30 ft. Roll of Foam Insulation Tape $13.95835-CIT-30 2" x 30 ft. Roll of Cork Insulation Tape $17.50

Note: Armacell closed cell insulation sold in 6 ft. lengths. OtherI.D. sizes and wall thicknesses available. Please call for pricing.

806-PS-1 810-63299-1

806-XR02CX 806-AKO13120

844-GLYRFT-100

852-GPA-PA301 845-315183-13 845-PA301 845-SYPC-1

845-2W685

816-ALDT-3150

816-ET-236 835-DT-1075 835-ET-7520

861-2A659 835-FIT-30 835-CIT-30

816-ALDT-4150

845-187483

845-RVPM-ASY

803-BR-MPHN-66

842-SPRAY-FOAM

816-343118

59

Air Shaft Flex Tubing, Insulation & Blowers



835-1070* 12 CFM, 3340 RPM, 1-1/4" Air Outlet, 115V Blower Only $66.95

837-1070-BRACKET Mounting Bracket for 1070 Blower $31.95

835-703-100A 1" Diameter Spring Coil Hose (Per Foot) $3.75

833-401-184A Hangar Clip for 703-100A Hose $2.40

842-PVC-1T 1" Barbed PVC Tee Fitting for 703-100A Hose $6.50

842-PVC-1S 1" Barbed PVC Splice Fitting for 703-100A Hose $4.50

842-PVC-1E 1" Barbed PVC Elbow Fitting for 703-100A Hose $5.50

Part Number Description Each835-1074* 89 CFM Short Range Blower Only (5-10 ft.) $87.95852-1074-A 89 CFM Short Range Blower Assembly (5-10 ft.) $128.95835-1071** 146 CFM Mid-Range Blower Only (10-20 ft.) $94.95852-1071-A 146 CFM Mid-Range Blower Assembly (10-20 ft.) $144.95835-1073*** 273 CFM Long-Range Blower Only (20-25 ft.) $113.95852-1073-A 273 CFM Long-Range Blower Assembly (20-25 ft.) $154.95826-4470B 3” Diameter Blower Hanger Bracket $23.95835-2W685 8' Cord and Plug $12.95855-RRC32 3” x 2” Rubber Reducer Coupling $8.50855-RRC34 3” x 4” Rubber Reducer Coupling $8.95

Note: Blower assemblies include blower, mounting bracket and 8’ cord and plug.All assemblies come standard with an 826-4470B mounting bracket. Reducers tosecure 2-1/2” and 1” flex tubing also available upon request. Blower may bemounted with air intake facing left or right for best proximity to coldest air. Pleasespecify desired orientation. All blowers must be direct wired.

Part Number Description 1-49 50’ Roll

874-1080-2A 2" Diameter Vinyl Flex Tubing $3.75/ft $3.15/ft

874-1080-25A 2-1/2" Diameter Vinyl Flex Tubing $4.75/ft $4.15/ft



Part Number Description Fits Flex Tubing Each

816-1180 2-7/8" I.D. x 1/2" Wall #1080-25A $3.50

816-1181-3A 3-1/2" I.D. x 1/2" Wall #1081-3A $3.75

816-1181-4A 4-1/2" I.D. x 1/2" Wall #1081-4A $4.90

Note: Armacell closed cell insulation sold in 6 ft. lengths. Flex tubing insulationmay be ordered with a larger wall size (3/4” or 1”). Please call for pricing.

Direct Draw Air Shaft Components

Short-Range, Mid-Range & Long-RangeAir Shaft Components

*835-1070 Blower should be used in runs of 5 ft or less; direct draw.

Flex Tubing Insulation

833-1070-BRACKET

835-1070

833-401-184A 835-703-100A 842-PVC-1T

835-1071

842-PVC-1E842-PVC-1S

835-2W685

Note: Vinyl Flex tubing is lightweight, durable, highly manueverable , will not rust,and is cheaper to ship and easier to install than galvanized or aluminum flex.Larger orders may ship via freight carrier. Please call for a shipping quote. Galvanized flex tubing available upon request. Call for pricing.

1/2” Wall Insulation

Vinyl Flex Tubing

Beer Lines

Cold Air Supply

Cold Air Return

Cold Air Return

(Tower to Cooler) 3” or 4” Vinyl Flex Tubing

(Cooler to Tower) 2”, 2-1/2” or 3” Vinyl Flex Tubing

826-4470B

855-RRC32


Air Shaft System Components & Picnic Pumps

Picnic Pumps


810-C23896-1 Baffle Plate for #810-C23907 Air Separator Base Kit $14.00

810-C23907 Air Separator Base Kit $79.00

842-FWH-4MFE PVC Elbow with Mounting Flange for 3" or 4" Flex Tubing $8.95

842-FWH-4MF PVC Mounting Flange for 3" or 4" Flex Tubing $8.95

842-PVCY2 PVC "Y" Fitting for 2" Flex Tubing $6.95



816-GMY3 Galvanized Metal "Y" Fitting for 3" Flex Tubing $29.95

816-GMY4 Galvanized Metal "Y" Fitting for 4" Flex Tubing $29.95

874-BRDCLP3 Stainless Steel Bridge Clamp for 3” Vinyl Flex Tubing $6.95

874-BRDCLP4 Stainless Steel Bridge Clamp for 4” Vinyl Flex Tubing $7.95

Air Shaft Duct Components

810-C23896-1

810-C23907

842-FWH-4MFE 842-FWH-4MF

842-PVCY3 816-GMY3

Air Separator KitDiagram

801-LTP211-MAXI 801-LTR211-MAXI

801-ESP211-M

Part Number Pump Height Coupler 1-11 12-24 25 +

801-LTP211-MAXI 4-3/4" Type "D" Lever $46.95 $44.95 $43.95

801-LTP211-M 8-1/4" Type "D" Lever $48.95 $46.95 $45.95

801-ESP211-MAXI 4-3/4" Type "D" Wing $38.95 $36.95 $35.95

801-ESP211-M 8-1/4" Type "D" Wing $40.95 $38.95 $37.95

801-ESP211-MAXI-MH 4-3/4" Type "D" Metal Wing $43.95 $41.95 $40.95

801-ESP211-M-MH 8-1/4" Type "D" Metal Wing $45.95 $43.95 $42.95

801-LTR211-MAXI 4-3/4" Type "S" Lever $51.25 $49.25 $48.25

801-LTR211-M 8-1/4" Type "S" Lever $53.25 $51.25 $50.25

Note: All pumps are made of heavy duty nickel plated brass and have a 5/16” diameter brasspump shaft. All couplers have a chrome plated brass probe. 801-LTP-211-MAXI and 801-LTP-211-Mcouplers come standard with a short lever handle. Long handle available upon request. All picnicpump assemblies come standard with 4 ft. of black 3/16” beer line and an 820-303A plastic faucethead. Please see page 29-31 for coupler replacement parts. See Page 87 for Coupler Master List.

874-BRDCLP3

61

Picnic Pumps


Part Number Description 1-11 12-23 24 +

800-FT42SP Taprite US Sankey "Super" Pump $38.95 $34.95 $33.50

810-40000B-PK Perlick US Sankey Piston "Party" Pump $52.95 $49.95 $48.95

800-BRP-1* Taprite US Sankey "Bronco" Pump $36.95 $34.95 $32.95

800-BRP-EUR* Taprite Euro Sankey "Bronco" Pump $40.95 $38.95 $36.95

800-BRP-4 Taprite US Sankey "Bronco" Pump with 4 Lines $69.95 $67.95 $65.95

800-BRP-EUR-4 Taprite Euro Sankey "Bronco" Pump with 4 Lines $69.95 $67.95 $65.95

800-POP-1* Taprite US Sankey "Pony" Pump $17.95 $16.95 $15.95

800-PP701** Taprite Beer Ball "Maverick" Pump $17.95 $16.95 $15.95

*Special pricing available for case quantities of 24 shipped direct from factory. Call for pricing.**Special pricing available for quantities of 100 + shipped direct from factory. Call for pricing.Note: Replacement parts available for all picnic pumps above. Please call for more information.

800-EUROA-MAXI

Part Number Pump Height Coupler Each

800-EUROA-MAXI 4-3/4" Euro Type "A" Lever $85.95

800-EUROA-TALL 8-1/4" Euro Type "A" Lever $87.95

800-EUROU-MAXI 4-3/4" Euro Type "U" Lever $86.95

800-EUROU-TALL 8-1/4" Euro Type "U" Lever $88.95

800-EUROG-MAXI 4-3/4" Euro Type "G" Lever $85.95

800-EUROG-TALL 8-1/4" Euro Type "G" Lever $87.95

800-FT42SP 810-40000B-PK

800-BRP-1

800-POP-1

800-BRP-4

800-PP701

Import Picnic Pumps

Note: All import picnic pumps come with 801-PPA-1 universal picnic pumpadapters. See Page 30 for European coupler replacement parts.

801-752-CH5000801-750A


801-750P Deluxe Picnic Pump Only (No Coupler) $54.95 $47.95

801-752-CH5000 Deluxe Picnic Pump with Taprite US Sankey Lever Handle Coupler $81.95 $78.95

801-752-CH5100 Deluxe Picnic Pump with Taprite Euro Sankey Lever Handle Coupler $82.95 $79.95

801-752-FT86P Deluxe Picnic Pump with US Sankey Plastic Wing Handle Coupler $81.95 $78.95

801-752-FT86M Deluxe Picnic Pump with US Sankey Metal Wing Handle Coupler $85.95 $82.95

801-752-EUROA Deluxe Picnic Pump with Euro Type A Lever Handle Coupler $112.95 $105.95

801-752-EUROU Deluxe Picnic Pump with Euro Type U Lever Handle Coupler $113.95 $106.95

801-752-EUROG Deluxe Picnic Pump with Euro Type G Lever Handle Coupler $112.95 $105.95

801-235 8-1/4” Pump with 5/16" Hose Barb for 801-750P Deluxe Picnic Pump $21.95 $18.25

801-780 Clamp Set for 801-750P Deluxe Picnic Pump (2 required) $6.95 N/A

801-750A Picnic Pump Rod Only $27.95 N/A

801-751 Picnic Pump Rod with 801-660B Faucet $38.95 N/A

Note: Deluxe picnic pumps come standard with an 8-1/4” pump, 801-750A pump rod, 2 sets of 801-780pump mounting clamps, 801-660B chrome plated brass faucet, pump lever knob, faucet knob and 1 ft. of5/16” red vinyl air line. Please call for more information.

Deluxe Picnic Pumps

62

Picnic Pump Replacement Parts



801-UN-235MAXI Universal Picnic Pump Assembly $32.50 N/A801-PPA-1 Universal Picnic Pump Adapter $13.95 $12.95801-761 Pump Adapter with 5/16" Barbed Nipple $5.50 N/A801-580-10 Female Beer Thread by Pump Thread Adapter $4.95 N/A820-303A Plastic Faucet Head Only $2.85 $2.55852-303B* Plastic Faucet Head with 4' of 3/16" Black Vinyl Hose Assembly $6.25 $5.95852-303C Plastic Faucet Head with 4' of 3/16" Black Vinyl Hose Only $4.95 $4.75819-K4WP 4 Piece “O” Ring Removal Kit $9.95 N/A800-FT101L 1 oz. Can of Probe Lubricant $3.95 N/A800-FT938 8 oz. Can of Probe Lubricant $15.95 N/A864-SLG-14 14 oz. Tube of USDA Approved Clear Grease for Picnic Pumps $14.65 N/A

*801-UN-234MAXI comes standard with a 4-3/4” pump, 801-PPA-1 pump adapter, 4’ of 3/16” blackvinyl beer line with 820-303A plastic faucet head, 1’ of 5/16” red vinyl air line, clamps and washer.**852-303B comes standard with 4’ of 3/16” black vinyl beer line, hex nut, 3/16” nipple, clamp and rubber washer.

Picnic Pump Parts & Tools

Pump Replacement Parts


1 801-235KS Round Plastic Pump Knob $1.85 $1.65

2 801-235CBS Threaded Metal Top Cap $2.75 $2.55

3 801-235SBS Pump Spring $.90 $.80

5 801-235PBS Piston and Nut assembly $3.25 $3.15

6a 815-OS-235R Oversized "O" Ring $.75 $.65

6b 815-ETOS-235R Extra Thick Oversized "O" Ring $1.50 $1.35

7a 801-235MBT-M 1-5/8" Pump Cylinder with Threaded Base (MAXI) $11.65 $11.25

7b 801-235MBT 1-5/8" Pump Cylinder with Threaded Base (TALL) $12.65 $12.25

8 801-753 Bottom Washer $.25 $.21

9 801-23 Thomas Valve $.46 $.42

10a 801-235-MAXI 8" Tall by 1-5/8" Diameter Complete Pump Assembly $18.25 $16.25

10b 801-235-TALL 11-1/2" Tall by 1-5/8" Diameter Complete Pump Assembly $19.95 $17.95

11a 801-IA-235-MAXI Complete Internal Assembly for #801-235-MAXI Pump $8.95 N/A

11b 801-IA-235-TALL Complete Internal Assembly for #801-235-TALL Pump $9.95 N/A


801-LTP-1 US Sankey Lever Handle Pump Coupler $27.95 $26.95

801-SP-1 US Sankey Plastic Wing Handle Pump Coupler $19.95 $18.95

801-SP-1MH US Sankey Metal Wing Handle Pump Coupler $24.95 $23.95

801-LTR-1 Euro Sankey Lever Handle Pump Coupler $29.95 $28.95

Pump Couplers

Note: See page 29-31 for coupler replacement parts.

801-UN-235MAXI

801-PPA-1801-761

801-580-10820-303A

852-303C819-K4WP

800-FT101L

864-SLG-14

801-LTP-1801-SP-1

801-LTR-1

1

2

3

5

6a

7a

8

9

11a

10a


Coil Box Coolers & Parts

Part Number Description Color 1-3 4 +

852-CD5201-120 Single Product 52 Qt. Coil Box Cooler Blue $249.95 $239.95

852-CD5202-120 Double Product 52 Qt. Coil Box Cooler Blue $469.95 $454.95

852-CD4803-3120 Triple Product 120 Qt. Coil Box Cooler Blue $725.95 $705.95

Note: All coolers come with 120 ft. stainless steel coils (100 ft. of 3/8” OD x 20 ft. of 1/4” OD),cooler coupling nuts, shanks and faucets. Cooler colors subject to change. Beer line jumpers,couplers, gas tanks and regulators not included. See below for beer jumpers, page 28 for couplers, page 37-38 for regulators and page 54 for gas tanks. Air Bars complete with 5/16” redor clear vinyl tubing may be mounted to cooler upon request. Please call for pricing. Customcoolers available. Call for pricing and information.


852-602-36 (H or W) 3 ft. x 3/8" I.D. Clear Vinyl Jumper $9.00




Note: Jumpers may be ordered with hex nuts at each end (H) or withone hex nut and one wing nut (W). Please specify H or W at the end ofthe part number when ordering. All jumpers include nipples, clampsand rubber beer washers. Custom jumpers available. Call for pricing.

Vinyl Beer Jumpers

Note: 801-DC-120R & 801-DC-120L consist of 100 ft. of 3/8” OD x 20 ft. of 1/4” OD coil. 801-SC-50R& 801-SC-50S consist of all 5/16” OD coil. All coils include grommets, ferrules and hex nuts.

Part Number Description Dimensions Each

801-DC-120R 120 ft. 304 Stainless Steel Coil (Right Positioned) 10-1/2" H x 9" Diameter $159.95

801-DC-120L 120 ft. 304 Stainless Steel Coil (Left Positioned) 10-1/2" H x 9" Diameter $159.95

801-SC-50R 50 ft. 304 Stainless Steel Coil (Single Stacked) 7" H x 9" Diameter $74.95

801-SC-50S 50 ft. 304 Stainless Steel Coil (Double Stacked) 7" H x 5" Diameter $77.95

Stainless Steel Coils


803-785G 1/4" O.D. Grommet $1.25

803-786G 3/8" O.D. Grommet $1.25

803-785F 1/4" O.D. Ferrule $2.95

803-786F 5/16" O.D. Ferrule $2.95

803-787F 3/8" O.D. Ferrule $2.95

802-218 Hex Nut $.79

801-219A-3 3" Long x 3/8" Bore Cooler Coupling $11.25

801-219A-4 4" Long x 3/8" Bore Cooler Coupling $13.25

Compression Fittings & Cooler Couplings

852-CD5201-120

852-CD5202-120

852-CD4803-3120

801-DC-120R

801-SC-50R 801-SC-50S

802-218 803-787F 803-785G 801-219A-3

852-602-60H

64

Cold Plate Coolers & Parts

Part Number Description Plate Size Color 1-3 4 +

852-520303 1 Product 48 Qt. Cold Plate Cooler 8"x 12" Blue $175.00 $170.00

852-520305 1 Product 48 Qt. Cold Plate Cooler 10" x 15" Blue $235.00 $225.00





Note: 8” x 12” plates have 11 ft. of stainless coil. 10” x 15” plates have 17 ft. of stainless coil.Cooler color subject to change. All coolers come with an aluminum cold plate, fittings, cold platestand, plastic sleeve assembly, faucets, shanks, black plastic faucet handle, 7 ft. of 5/16” ID clearvinyl jumpers with wing nuts, clamps and rubber washers. Plastic sleeve assemblies may be substituted with an 801-219A-3 cooler coupling (see page 63). Add $13.95 per product and suffix “-CCKJ” when ordering. Gas tanks, couplers and regulators not included. See page 28 forcouplers, page 37-38 for regulators and page 54 for gas tanks. Air Bars complete with 5/16” red orclear vinyl tubing may be mounted to cooler upon request. Please call for pricing. Custom coolersavailable. Call for pricing and information.

Part Number Description Plate Size Coil Length Each

802-308-1 1 Product Aluminum Cold Plate 8-1/4" x 14" 12' $80.95



802-309-S 1 Product Aluminum Cold Plate 8" x 12" 11' $64.50

802-309-D 2 Product Aluminum Cold Plate 8" x 12" 11' $71.50

802-309-3 3 Product Aluminum Cold Plate 8" x 12" 11' $113.95


802-310-S 1 Product Aluminum Cold Plate 10" x 15" 17' $86.50

802-310-D 2 Product Aluminum Cold Plate 10" x 15" 17' $96.50


Aluminum Cold Plates

Note: All cold plates include stainless steel barbed fittings. Specify size when ordering.


802-SS-CPRK Stainless Steel Cold Plate Rack $17.00

802-SS-MFHN-45 1/4" Barb x 5/16" MF Stainless Steel Hose Barb $1.95

802-SS-MFHN-65 3/8" Barb x 5/16" MF Stainless Steel Hose Barb $2.25

802-NYFW-5 5/16" Nylon Washer $.15

805-SLEEVE-ASSY* 2-3/4" Long Plastic Sleeve Assembly with Washers & Lock Nuts $3.50

805-DRAIN-ASSY** Plastic Sleeve Assembly with Washers, Lock Nuts & 1/2" Plastic Hose Barb $3.95

805-DRAIN-CAP Plastic Drain Cap for #805-DRAIN-ASSY $1.80

*Works with cooler walls up to 2” thick and tubing up to 3/4” OD.**Works with cooler walls up to 1” thick and hose barb fits tubing with 1/2” ID.


Cold Plate Cooler Parts & Accessories

852-520303 852-520302

852-520304

852-520305

802-310-D

802-SS-CPRK 802-SS-MFHN-45 802-NYFW-5

805-SLEEVE-ASSY

805-DRAIN-ASSY

805-DRAIN-CAP

65

Tote-A-Tap Coolers, Clamp-On Towers & Keg Tubs



852-STT-R Single Product 28 Qt. Tote-A-Tap Cooler $219.95 $209.95

852-DTT-R Double Product 28 Qt. Tote-A-Tap Cooler $289.95 $279.95

852-STT-R Features:- 28 Qt. Red Cooler with Handle (6-1/2 Gallon Capacity)- Single Product, 8” x 12” Aluminum Cold Plate with Fittings- 800-T741-60 Single Gauge Regulator with 5’ of 5/16” Air Line & Clamps- Chrome Faucet, Shank and Black Plastic Faucet Handle- 6’ of 3/8” Beer Line, All Fittings & Plastic Sleeve Assembly- Plastic Drain Assembly

852-DTT-R Features:- 28 Qt. Red Cooler with Handle (6-1/2 Gallon Capacity)- Double Product, 8” x 12” Aluminum Cold Plate with Fittings- 800-T741-60-2 Single Gauge Regulator with Air “Y” and Two 5’ pieces of Air Line & Clamps- Chrome Faucets, Shanks and Black Plastic Faucet Handles- 6’ of 3/8” Beer line (per product), All Fittings & Plastic Sleeve Assemblies- Plastic Drain Assembly

Note: Cooler color and style subject to change. See below for optional accessories.

Single Product Tote-A-Tap Accessories Double Product Tote-A-Tap Accessories


852-STT-4 4 lb. Reconditioned Steel CO2 Tank $50.50



852-STT-LT US Sankey Lever Handle Coupler $23.95

852-STT-EC Euro Sankey Lever Handle Coupler $25.00

852-STT-DR #800-T742-60 Double Gauge Regulator $5.50


852-DTT-5 5 lb. Reconditioned Steel CO2 Tank $52.50



852-DTT-LT 2 - US Sankey Lever Handle Couplers $47.95

852-DTT-EC 2 - Euro Sankey Lever Handle Couplers $49.95

852-DTT-DR #800-T742-60-2 Double Gauge Regulator $5.50

Note: Optional Accessories above are priced specifically for purchase with Tote-A-Tap coolers. Add price of Tote-A-Tap cooler to the price ofany of the optional accessories listed for total price. Custom cooler options available. Call for more information and pricing.


817-LCCOTB-618SS Single Product Clamp-On Tower with Stainless Steel Drip Tray $179.95

817-LCCOTB-619SS Double Product Clamp-On Tower with Stainless Steel Drip Tray $205.95

817-LCCOTB-620SS Triple Product Clamp-On Tower with Stainless Steel Drip Tray $259.95

817-LCCOTB-L3T Clamp-On Tower Base and Stainless Steel Drip Tray Only $99.95

Clamp-On Towers

Note: Faucet handles not included. Clamp-on tower base must be used with towers with a 3”diameter column. Drip pan measures 8-1/8” W x 5-1/8” D x 3/4” H. Clamp adjusts from 1-1/4” to4-1/8”. Base comes complete with predrilled bolt and cylinder holes and a 1/2” drain fitting.See page 19-21 for tower replacement parts & accessories.

817-LCCOTB-619SS

Part Number Description 1-11 12-23 24 +

829-KPT-1R Red Keg Tub $31.95 $30.50 $28.95

829-KPT-1B Blue Keg Tub $31.95 $30.50 $28.95

829-KPT-1BK Black Keg Tub $31.95 $30.50 $28.95

880-KC-100-RV Red Insulated Keg Jacket $45.95 $42.95 $39.95

Keg Tubs & Jackets

Note: Keg tubs made of high density polyethylene and measure 24” OD, 22”ID, 13-3/4” Tall and 19-3/8” Wide at the base. 8 tubs can ship per box. Kegjacket fits 1/2 barrels (straight wall or barrel type) and has a 5-1/2” slot forcoupler and easy access to keg lug.

829-KPT-1R 880-KC-100-RV

852-DTT-R

66

Conversion Kits



852-C240 US Sankey Kit with 5 lb. CO2 Tank $169.95852-C240-LC US Sankey Kit Less CO2 Tank $115.00852-SS-C240 US Sankey S/S Kit with 5 lb. CO2 Tank $225.00852-SS-C240-LC US Sankey S/S Kit Less CO2 Tank $170.00

US Sankey Refrigerator Conversion Kit

KITS INCLUDES:- Double Gauge CO2 Regulator - 5 lb. Reconditioned Steel CO2 Tank (Optional)- 5’ of 5/16” Red Vinyl Air Line with Clamps- 6’ of 3/16” Clear Vinyl Beer Line with Fittings- 5” Long x 1/4” Bore Complete Shank- US Sankey Lever Handle Coupler- Chrome Plated Brass US Faucet with Black Handle- Installation Instructions

Note: S/S kit comes with all stainless steel fittings, coupler,shank and faucet. Kit comes standard with Perlick 810-630SSfaucet. Standard US 304 S/S faucet available upon request.


852-C540 Euro Sankey Kit with 5 lb. CO2 Tank $169.95

852-C540-LC Euro Sankey Kit Less CO2 Tank $115.00

852-SS-C540 Euro Sankey S/S Kit with 5 lb. CO2 Tank $225.00

852-SS-C540-LC Euro Sankey S/S Kit Less CO2 Tank $170.00

Euro Sankey Refrigerator Conversion Kit

KITS INCLUDES:- Double Gauge CO2 Regulator - 5 lb. Reconditioned Steel CO2 Tank (Optional)- 5’ of 5/16” Red Vinyl Air Line with Clamps- 6’ of 3/16” Clear Vinyl Beer Line with Fittings- 5” Long x 1/4” Bore Complete Shank- Euro Sankey Lever Handle Coupler- Chrome Plated Brass US Faucet with Black Handle- Installation Instructions

Note: S/S kit comes with all stainless steel fittings, coupler,shank and faucet. Kit comes standard with Perlick 810-630SSfaucet. Standard US 304 S/S faucet available upon request.

European Stout Refrigerator Conversion Kit

KITS INCLUDES:- Double Gauge Mixed Gas/N2 Regulator - 20 CFM Reconditioned Steel Mixed Gas Tank (Optional)- 5’ of 5/16” Red Vinyl Air Line with Clamps- 6’ of 3/16” Clear Vinyl Beer Line with Fittings- 5” Long x 1/4” Bore Complete Shank- European Type “U” Lever Handle Coupler- Chrome Stout Faucet with Black Handle- Installation Instructions

Note: S/S kit comes with all stainless steel fittings and Shank. Flow ControlEuropean faucets available upon request. Please call for pricing. Chromestout faucet may be substituted for a PVD Brass stout faucet. Please specify when ordering.


852-ESCFG-20MGT Stout Kit with 20 CFM Mixed Gas Tank $280.00

852-ESCFG-NT Stout Kit Less Mixed Gas Tank $225.00

852-SS-ESCFG-20MGT S/S Stout Kit with 20 CFM Mixed Gas Tank $292.00

852-SS-ESCFG-NT S/S Stout kit Less Mixed Gas Tank $230.00

67

Conversion Kits

Deluxe US Sankey Refrigerator ConversionKit


852-C240-DLX Deluxe US Sankey Kit with 5 lb. CO2 Tank $234.95

KITS INCLUDES:- Double Gauge CO2 Regulator with ORSA Stem- 5 lb. Reconditioned Steel CO2 Tank (Optional)- 5’ of 5/16” Red Vinyl Air Line with Clamps- 6’ of 3/16” Clear Vinyl Beer Line with Fittings- 5” Long x 1/4” Bore Complete Shank- US Sankey Lever Handle Coupler- Chrome Plated Brass US Faucet with Black Handle- Regulator Wrench- Economy Cleaning Kit with 4 oz. Bottle of BLC formula, Spanner Wrench, Ball Lifter, Brush & Cleaning attachment for standard US Shanks- S/S wall mount drip tray with plastic grid- Installation & Cleaning Kit Instructions

Note: Stainless Steel kits available. US Sankey components maybe substituted for Euro Sankey components upon request. Callfor pricing.

Dual US Sankey Refrigerator ConversionKit


852-C240-DUAL Dual US Sankey Kit with 5 lb. CO2 Tank $239.95

KITS INCLUDES:- Double Gauge CO2 Regulator with Beer “Y”- 5 lb. Reconditioned Steel CO2 Tank (Optional)- Two 5’ of 5/16” Red Vinyl Air Line with Clamps- Two 6’ of 3/16” Clear Vinyl Beer Line with Fittings- Two 5” Long x 1/4” Bore Complete Shank- Two US Sankey Lever Handle Coupler- Two Chrome Plated Brass US Faucet with Black Handles- Installation Instructions

Note: Stainless Steel kits available. US Sankey components maybe substituted for Euro Sankey components upon request. Callfor pricing.

US Sankey Refrigerator Conversion Kit withTower


852-C240-T US Sankey Tower Kit with 5 lb. CO2 Tank $226.95

852-C240-T-LC US Sankey Tower Kit Less 5 lb. CO2 Tank $185.95

852-C540-T Euro Sankey Tower Kit with 5 lb. CO2 Tank $227.95

852-C540-T-LC Euro Sankey Tower Kit Less 5 lb. CO2 Tank $190.95

KITS INCLUDES:- Double Gauge CO2 Regulator - 5 lb. Reconditioned Steel CO2 Tank (Optional)- 5’ of 5/16” Red Vinyl Air Line with Clamps- Single Product 3” Column S/S Tower with Beer Line- Chrome Plated Brass US Faucet with Black Handle- US Sankey Lever Handle Coupler- Installation Instructions

Note: Stainless Steel kits available. Call for pricing.


68

Conversion Kit Accessories

Part Number Description Dimensions Drain Each

808-WMPDT-552 Black Plastic Drip Tray with Stainless Grid and Mounting Bracket 5-3/4" W x 5-3/4" D x 2-3/8" H No $49.95

834-1525A Stainless Steel Wall Mount Drip Tray with Plastic Grid and Predrilled Hole 6-1/8" W x 4-3/4" D x 10-3/4" H 1/2" MPT $53.95

834-1525C Stainless Steel Drip Tray with Plastic Grid and Mounting Holes 6-1/8" W x 4-3/4" D x 5-1/4" H No $42.95

Note: Mounting screws not included with above drip trays. See page 27 for drip tray replacement parts and drain fittings.


803-CWMA-KIT Stainless Steel CO2 Wall Mount Adapter Kit $13.50

852-DBK-1 1 Qt. Drain Bottle Kit with #833-205-151A Drain Adapter $11.95

852-MPK-1 Plastic Faucet and Beer Line Adapter $6.95


837-FTC-2080 Mechanical Thermostat Freezer Temperature Controller $59.95

Adapter Kits

Conversion Kit Drip Trays

Temperature Controllers

803-CWMA-KIT includes all components shown above; 3-1/2” Long x 7/16” ODthreaded shank with lock nuts & washers, two 1/4” swivel nuts, two 5/16” ODstainless steel swivel stems and two 1/4” nylon flare washers. Kit allows for airtank to be stored outside of a cooler or refrigerator.

852-DBK-1 kit includes a 1 qt. plastic drain bottle, 2 ft. of clear vinyl drain lineand drain adapter.

852-MPK-1 kit includes plastic beer faucet, 5 ft. of 3/16” Black vinyl beer line,hex nut, nipple, clamp and rubber washer.

Note: Temperature controller turns any freezer into a refrigerator for storing kegs.Controller has an adjustable 20°F and 80°F set point range, fixed differential, and isenclosed in a rugged steel box. Includes a rotary dial adjustment, 1/16” diameter gas-filled sensor tube, 6 ft. power cord and 6 ft. outlet cord. Simply plug the freezer intothe outlet cord, place the sensor tube in the area to be controlled and program thedesired temperature. Instruction manual included.

837-FTC-2080

852-MPK-1

852-DBK-1

803-CWMA-KIT

808-WMPDT-552

834-1525A834-1525C



Portable Beer Dispensers

Part Number Description Unit Unit Complete

806-KEGMASTER-618 Kegmaster Portable Beer Dispenser with Single Product Tower $965.00 $1,180.00

- 1/5 HP Commercial Grade Compressor, R134A refrigerant- All stainless steel interior walls, components and floor- Two evaporator fans- Stainless steel top with glass rails and stainless drip tray- Self-closing door with lock and key- Adjustable temperature control (23°F-41°F)- 4” Heavy duty casters with front wheel locking- Automatic condensation evaporator- 2” thick polyurethane foam insulated top, 1-3/4” thick walls- Black epoxy coated exterior- 9/16” OD capped access hole at back wall for running air line outside unit- 15 amp dedicated circuit, 3.7 amp work load- 115V, 60 V/HZ, 1 Phase; includes 6 ft. plug-in cord- 24” W x 32” D x 40” H; 51-5/8” H with tower- 150 lb. Net weight, 205 lb. Gross weight- Keg Capacity:

1/2 Barrel - 11/4 Barrel - 21/6 Barrel - 4

WARRANTY: 1 Year Parts & Labor, 5 Year Compressor

UBC Kegmaster 2

Note: Breaking pricing and free freight available with the purchase of 4 or more units. Call for details and pricing. Unit pricing includesKegmaster unit and a single product 800-618SS 3” column tower and faucet. Complete unit comes with an 800-618SS 3” columntower, faucet, black plastic faucet handle, 3/16” clear beer line and fittings, 800-T742-60 double gauge CO2 regulator, 800-CH5000 USSankey Coupler, 5/16” red gas line and an 830-5CO2RS 5 lb. CO2 tank (empty). Other tap configurations and coupler styles available.Please call for more information.

Part Number Description Exterior Unit Unit Complete

833-BM23-B Bev-Air Portable Beer Dispenser with Single Product Tower Black $1,350.00 $1,565.00

833-BM23-S Bev-Air Portable Beer Dispenser with Single Product Tower Stainless $1,725.00 $1,940.00

833-BM23C-B Bev-Air Club Model Portable Beer Dispenser with Single Product Tower Black $1,590.00 $1,805.00

833-BM23C-S Bev-Air Club Model Portable Beer Dispenser with Single Product Tower Stainless $1,950.00 $2,160.00

- 1/5 HP Commercial Grade Compressor, R134A refrigerant- Galvanized interior walls, stainless steel floor- Stainless Steel top with glass rails and stainless drip tray- Self-closing door with lock and key- Forced air cooling system with 1” blower hose - 4” heavy duty casters with front wheel locking- Self-defrosting with adjustable thermometer- Black wear-resistant vinyl exterior (BM23-B & BM23C-B)- Stainless Steel exterior (BM23-S & BM23C-S)- Club models feature an easy glide stainless steel lid for additional storageof glasses cans & bottles. Includes epoxy coated shelving.- 2” thick polyurethane foam insulated top, 1-1/2” thick walls- 15 amp dedicated circuit, 4 amp work load- 115V, 60 V/HZ, 1 Phase; includes 8 ft. plug in cord- 24” W x 29-1/2” D x 39” H; 50-5/8” H with tower (BM23-B & BM23-S)- 24” W x 29-1/2” D x 40-1/2” H; 52-1/8” H with Tower (BM23C-B & BM23C-S)- 180 lb. Gross weight (BM23-B & BM23-S)- 186 lb. Gross weight (BM23C-B & BM23C-S)- Keg Capacity:

1/2 Barrel - 1 (All Units)1/4 Barrel - 1 (All units)1/6 Barrel - 3 (BM23-B & BM23-S)

2 (BM23C-B & BM23C-S)

WARRANTY: 3 Year Parts & Labor, 5 Year Compressor

Beverage-Air BM23

Note: Unit pricing includes Bev-Air unit and a single product tower with faucet. Club models come with a 2-1/2” column tower; standard units come with a 3” column tower. Complete unit comes with a single product tower (2-1/2” or 3”), faucet, black plasticfaucet handle, 3/16” clear beer line and fittings, 800-T742-60 double gauge CO2 regulator, 800-CH5000 US Sankey Coupler, 5/16” redgas line and an 830-5CO2RS 5 lb. CO2 tank (empty). Other tap configurations and coupler styles available. Please call for more information.

833-BM23-B

806-KEGMASTER-618


Portable Beer Dispensers & Replacement Parts

Continental KC24

Part Number Description Exterior Unit Unit Complete

856-KC24 Continental Portable Beer Dispenser with Single Product Tower Black $1,450.00 $1,665.00

856-KC24-SS Continental Portable Beer Dispenser with Single Product Tower Stainless $1,850.00 $2,065.00

- 1/5 HP Commercial Grade Compressor, R134A refrigerant- Galvanized interior walls, stainless steel floor- Stainless Steel top with glass rails and stainless drip tray- Self-closing door with lock and key- Forced air cooling system with 1” blower hose - 4” heavy duty casters with front wheel locking- Automatic, non-electric condensate disposal- Black wear-resistant enamel exterior (KC24)- Stainless Steel exterior; front door and side walls (KC24-SS)- 2” thick polyurethane foam insulated top, 1-1/2” thick walls- 15 amp dedicated circuit, 5.8 amp work load- 115V, 60 V/HZ, 1 Phase; includes 10 ft. plug in cord- 24” W x 31-1/8” D x 38-1/2” H; 50-1/8” H with tower- 175 lb. Gross weight (KC24)- 193 lb. Gross weight (KC24-SS)- Keg Capacity:

1/2 Barrel - 1 1/4 Barrel - 1 1/6 Barrel - 3

WARRANTY: 1 year Parts & Labor, 5 Year Compressor

Note: Free base freight on all KC24 units. Free freight does not include the cost of a lift gate, residential delivery or call aheadservice. Please call for pricing information. Unit pricing includes KC24 unit and a single product 800-618SS 3” column tower andfaucet. Complete unit comes with an 800-618SS 3” column tower, faucet, black plastic faucet handle, 3/16” clear beer line and fittings, 800-T742-60 double gauge CO2 regulator, 800-CH5000 US Sankey Coupler, 5/16” red gas line and an 830-5CO2RS 5 lb.CO2 tank (empty). Other tap configurations and coupler styles available. Please call for more information.

856-KC24 856-KC24-SS


833-205-150A Drain Flange (1/2" Male Thread) $4.05

833-205-151A Drain Adapter (1/2" FPT x 1/2" Nipple) $4.05

833-502-289B BM23 Thermostat (Models Before 1994) $43.80

833-502-290B BM23 Contact Thermostat (Models After 1994) $43.80

833-28B04-01AAA Beverage-Air Lock Assembly $49.99

833-401-546A Set of Two Keys for Bev-Air Lock Assembly $6.09

833-32C14-008A BM23 Replacement Fan Assembly $165.95

833-703-195CAA BM23 Door Gasket $26.05

833-04A02-325C-03 BM23 Blower Housing $39.50

833-28A06-004C BM23 14-1/2" x 5-1/8" Removable Splash Grid $30.50

833-401-113AAAC Condensate Pan Spring $4.20

833-703-481A Condensate Pan Wick $2.40

833-703-369C BM23 Plastic Fan Guard $10.05

852-DBK-1 Drain Bottle Kit $11.95

Beverage-Air Replacement Parts

833-32C14-008A833-703-195CAA

852-DBK-1

833-502-290B

833-28B04-01AAA

833-401-546A

833-205-151A 833-205-150A

71

Beverage-Air Direct Draw Coolers

Part Number W D H HP Doors Kegs (SW) Kegs (BT) Black Exterior S/S Front S/S Exterior

833-DD48* 48" 23-1/2" 36" 1/4 2 2 0 $2,700.00 N/A $2,850.00

833-DD50 50-1/2" 28-3/16" 37-1/4" 1/3 2 2 2 $2,700.00 $2,850.00 $2,975.00

833-DD50C 50-1/2" 28-3/16" 38-3/4" 1/3 2 2 2 $2,655.00 $3,075.00 N/A

833-DD58 59" 28-3/16" 37-1/4" 1/3 2 3 2 $2,290.00 $2,695.00 N/A

833-DD58C 59" 28-3/16" 38-3/4" 1/3 2 3 2 $2,625.00 $2,950.00 N/A

833-DD68 69" 28-3/16" 37-1/4" 1/3 2 3 3 $2,375.00 $2,965.00 N/A

833-DD68C 69" 28-3/16" 38-3/4" 1/3 2 3 3 $2,700.00 $3,125.00 N/A

833-DD72* 72" 23-1/2" 36" 1/4 3 3 0 $2,850.00 N/A $3,150.00

833-DD78 79" 28-3/16" 37-1/4" 1/3 3 4 4 $2,925.00 $3,195.00 N/A

833-DD94 95" 28-3/16" 37-1/4" 1/3 3 5 5 $2,925.00 $3,425.00 N/A

Model Towers Standard Total Faucets Air Bar

DD48 1 Dual 2 2 way

DD50 1 Dual 2 2 way

DD58 1 Single, 1 Dual 3 3 way

DD68 1 Single, 1 Dual 3 3 way

DD72 2 Dual 4 4 way

DD78 2 Dual 4 4 way

DD94 2 Dual 4 4 way

Standard Configurations

Note: 833-DD48 & 833-DD72 are shallow depth models and are tested and certified

for ambient temperatures up to 100°F. S/S front models have an all stainless steel

front with grey enamel sides and back. All other units have a black vinyl exterior.

All models have polished galvanized interior with stainless steel floor. Complete

S/S interior available at an additional cost. 40°F-60°F wine dispensing models

available. Call for information and pricing. All units may be upgraded to other tap

configurations; see page 8 and 18 for tower options. Upgraded towers must be

purchased seperately. Standard towers that come with units will not be credited

towards the cost of any upgrades. Pass-thru towers may be installed on units

with two 3” tower holes, but customer assumes responsibility for installation and

enuring measurements and mounting holes align correctly. Units do not include

gas regulator, gas tank or couplers. Complete assembled units available at an

additional charge. Call for pricing. All Beverage-Air units come factory wired for a

115V/60 V/HZ/1 Phase, 15 amp dedicated circuit. 8 ft. plug in power cord included.

All units must ship via freight carrier. Please call for shipping quote.

Warranty: 3 Year Parts & Labor, 5 Year Compressor


833-DD48

“C” - Club Top Model with sliding lid(s) and glass storage

shelving

833-DD50 833-DD58

833-DD68C 833-DD72

833-DD78 833-DD94

*Shallow depth model (23-1/2”)

72

Continental Direct Draw Coolers

Part Number W D H HP Doors Kegs (SW) Kegs (BT) Black Exterior S/S Exterior

856-KC50 50" 29-1/4" 36-3/4" 1/3 2 2 0 $2,375.00 $2,890.00

856-KC59 59" 29-1/4" 36-3/4" 1/3 2 3 2 $2,390.00 $2,950.00

856-KC69 69" 29-1/4" 36-3/4" 1/3 2 3 3 $2,490.00 $3,125.00

856-KC79 79" 29-1/4" 36-3/4" 1/3 3 4 4 $2,950.00 $3,650.00

856-KC90 90" 29-1/4" 36-3/4" 1/2 3 5 4 $3,050.00 $3,725.00

856-KC50SD 50" 25-1/4" 36-3/4" 1/3 2 2 0 $2,725.00 $2,940.00

856-KC59SD 59" 25-1/4" 36-3/4" 1/3 2 2 2 $2,750.00 $2,975.00

856-KC69SD 69" 25-1/4" 36-3/4" 1/3 2 3 3 $2,850.00 $3,175.00

856-KC79SD 79" 25-1/4" 36-3/4" 1/3 3 3 3 $3,275.00 $3,725.00

856-KC90SD 90" 25-1/4" 36-3/4" 1/2 3 4 4 $3,350.00 $3,775.00

Model Towers Standard Total Faucets Air Bar

KC50 1 Dual 2 2 way

KC59 2 Single 2 2 way




“SD” - Shallow Depth Model

Note: Free base freight on all Continental units. Free freight does not include the

cost of a lift gate, residential delivery or call ahead service. Please call for pricing

and more information. Standard units come with black enamel exterior. S/S units

have an all stainless steel exterior. Each unit has interior lighting, galvanized

interior walls and stainless floor and top. All units may be upgraded to other tap

configurations; see page 8 and 18 for tower options. Upgraded towers must be

purchased seperately. Standard towers that come with units will not be credited

towards the cost of any upgrades. Pass-thru towers may be installed on units

with two tower holes, but customer assumes responsibility for installation and

enuring measurements and mounting holes align correctly. Units do not include

gas regulator, gas tank or couplers. Complete assembled units available at an

additional charge. Call for pricing. All Continental units come factory wired for a

115V/60 V/HZ/1 Phase, 15 amp dedicated circuit. 10 ft. plug in power cord

included. Units may be ordered with left or right side condensing unit. Please

specify when ordering. Custom options available; units may be ordered with one

glass door and shelving for bottle storage. Call for pricing and other

options.

Warranty: 3 Year Parts & Labor, 5 Year Compressor

Options:

- Epoxy-Coated Shelves with Clips

- Stainless Steel Shelves with Clips

- Wine Rack

- Stainless Steel Interior Walls

- Remote Models

- Expansion Valve System

- Casters or Legs

- Automatic Electric Condensate Evaporator

- Left or Right Side Condensing Unit

- Custom Tower Mounting Hole and Drip Tray Placement

856-KC50 856-KC59 856-KC69

856-KC79 856-KC90


73

Beverage-Air Back Bar Coolers


Note: Keg capacities listed above are only applicable to straight wall kegs. All units come standard with galvanized interior walls and

reinforced stainless steel floors. Units with S/S front have grey enamel sides and back. All units may be custom ordered with a complete

stainless steel exterior (except BB48 & BB72). Pass-Thru models and units with sliding glass doors available. Please call for more information

and pricing. All units must ship via freight carrier. Please call for a freight quote. Spec sheets available upon request.

Features:- 2” Thick Stainless Steel top

- 1-1/2” Foamed-in-place polyurethane insulation

- Interior, incandescent lighting with manual on/off switch

- Self-closing doors with locks

- Balanced, forced-air refrigeration system (shallow depth models feature lift-out

refrigeration systems)

- Factory wired for a 115V/60V/HZ/1 phase, 15 amp dedicated circuit

- 8 ft. plug-in power cord

- R134a refrigerant

Warranty: 3 Years Parts & Labor, 5 Year Compressor

833-BB48833-BB48-GD 833-BB58

833-BB72833-BB78

833-BB94

Part Number W D H HP Doors/Shelves Kegs (SW) Solid Door Glass Door

833-BB481 48" 23-1/2" 36" 1/4 2/4 2 $2,325.00 $2,575.00833-BB58 59" 28-3/16" 37-1/4" 1/3 2/4 2 $2,175.00 $2,590.00833-BB68 69" 28-3/16" 37-1/4" 1/3 2/4 3 $2,275.00 $2,625.00

833-BB721 72" 23-1/2" 36" 1/4 3/6 3 $2,595.00 $2,985.00833-BB78 79" 28-3/16" 37-1/4" 1/3 3/6 4 $2,925.00 $3,050.00833-BB94 95" 28-3/16" 37-1/4" 1/3 3/6 5 $2,550.00 $2,950.00

833-BB48SS1 48" 23-1/2" 36" 1/4 2/4 2 $2,725.00 $2,850.00833-BB58SS2 59" 28-3/16" 37-1/4" 1/3 2/4 2 $2,495.00 $2,875.00833-BB68SS2 69" 28-3/16" 37-1/4" 1/3 2/4 3 $2,650.00 $2,890.00

833-BB72SS1 72" 23-1/2" 36" 1/4 3/6 3 $3,350.00 $3,425.00833-BB78SS2 79" 28-3/16" 37-1/4" 1/3 3/6 4 $3,425.00 $3,450.00833-BB94SS2 95" 28-3/16" 37-1/4" 1/3 3/6 5 $3,175.00 $3,490.00

1 Shallow depth (23-1/2”) model. Stainless steel shallow depth models have an all stainless steel exterior (front, top, and sides).2 Standard depth (28-3/16”) stainless steel models have a stainless steel front and top only with gray enamel sides.

Note: All units come standard with a stainless steel top. Units with no tops available upon request. Please call for pricing.

74

Continental Back Bar Coolers

Part Number W D H HP Doors/Shelves Kegs (SW) Solid Door Glass Door Sliding Glass Door

856-BBC50 50" 29-1/4" 38-1/2" 1/3 2/4 2 $2,275.00 $2,725.00 $3,150.00

856-BBC59 59" 29-1/4" 38-1/2" 1/3 2/4 2 $2,300.00 $2,825.00 $3,225.00

856-BBC69 69" 29-1/4" 38-1/2" 1/3 2/4 3 $2,350.00 $2,890.00 $3,325.00

856-BBC79 79" 29-1/4" 38-1/2" 1/3 3/6 4 $2,550.00 $3,290.00 N/A

856-BBC90 90" 29-1/4" 38-1/2" 1/2 3/6 5 $2,750.00 $3,350.00 N/A

856-BBC50SS 50" 29-1/4" 38-1/2" 1/3 2/4 2 $2,450.00 $2,850.00 $3,150.00

856-BBC59SS 59" 29-1/4" 38-1/2" 1/3 2/4 2 $2,575.00 $2,925.00 $3,225.00

856-BBC69SS 69" 29-1/4" 38-1/2" 1/3 2/4 3 $2,980.00 $3,475.00 $3,590.00

856-BBC79SS 79" 29-1/4" 38-1/2" 1/3 3/6 4 $3,250.00 $3,825.00 N/A

856-BBC90SS 90" 29-1/4" 38-1/2" 1/2 3/6 5 $3,480.00 $3,925.00 N/A

Part Number W D H HP Doors/Shelves Solid Door Glass Door Sliding Glass Door

856-BBC50-PT 50" 31-3/8" 36-3/4" 1/3 2/4 $2,850.00 $3,950.00 $4,475.00

856-BBC59-PT 59" 31-3/8" 36-3/4" 1/3 2/4 $2,850.00 $3,990.00 $4,675.00

856-BBC69-PT 69" 31-3/8" 36-3/4" 1/3 2/4 $2,925.00 $4,125.00 $4,750.00

856-BBC79-PT 79" 31-3/8" 36-3/4" 1/3 3/6 $3,390.00 $4,675.00 N/A

856-BBC90-PT 90" 31-3/8" 36-3/4" 1/2 3/6 $3,550.00 $4,775.00 N/A

856-BBC50SS-PT 50" 31-3/8" 36-3/4" 1/3 2/4 $3,125.00 $4,075.00 $4,475.00

856-BBC59SS-PT 59" 31-3/8" 36-3/4" 1/3 2/4 $3,325.00 $4,125.00 $4,675.00

856-BBC69SS-PT 69" 31-3/8" 36-3/4" 1/3 2/4 $3,625.00 $4,650.00 $4,925.00

856-BBC79SS-PT 79" 31-3/8" 36-3/4" 1/3 3/6 $4,175.00 $5,250.00 N/A

856-BBC90SS-PT 90" 31-3/8" 36-3/4" 1/2 3/6 $4,450.00 $5,275.00 N/A

Pass-Thru Models

Standard Models

Options:

- Epoxy-Coated Shelves with Clips

- Stainless Steel Shelves with Clips

- Wine Rack

- Stainless Steel Interior Walls

- Shallow Depth Models (23”)

- Expansion Valve System

- Casters or Legs

- Automatic Electric Condensate Evaporator

- Left or Right Side Condensing Unit

Note: Free base freight on all Continental units. Free freight does not include the

cost of a lift gate, residential delivery or call ahead service. Please call for pricing

and more information. Keg capacities listed above are only applicable to straight

wall kegs. Standard units come with black enamel exterior. S/S units have an all

stainless steel exterior. Shallow depth models available in black enamel or S/S

exteriors. Please call for pricing. Each unit has LED interior lighting, galvanized

interior walls, stainless floor and stainless top. All Continental units come factory

wired for a 115V/60 V/HZ/1 Phase, 15 amp dedicated circuit. 10 ft. plug in power

cord included. Units may be ordered with left or right side condensing unit. Please

specify when ordering. Undercounter back bar units also available. Call for more

information.

WARRANTY: 3 Years Parts & Labor, 5 Year Compressor


856-BBC50

Note: Shallow depth units available for both standard and pass-thru models. Call for pricing.

856-BBC50-GD 856-BBC69

856-BBC79

856-BBC90

75

Keg Storage

KSR Series:

- Frame Constructed of 1-1/2” square heli-arc

welded aluminum tubing.

- Shelves are 2-7/8” arch channels heli-arc welded

to frame.

- Fully assembled.

KAR Series:

- Heavy duty extruded aluminum construction.

- Shelves are 4” “E” channel heli-arc welded.

- Tubular top shelf for general merchandise.

- Ships knocked down, easy to assemble.

- Adjustable shelf heights for 1/4, 1/6 or 1/2 barrels

KDR Series:

- 4” “E” channel tubular frame.

- Fully assembled.

- May be used to elevate glycol power packs.

Part Number W D H Type Weight Kegs Each

867-KSR48 48" 20" 55" Fully Assembled 35 lbs. 4 $380.00

867-KSR72 71-1/2" 20" 55" Fully Assembled 50 lbs. 8 $420.00

867-KAR42 42" 17" 68" Knock Down 44 lbs. 4 $370.00





867-KDR136 36" 18" 12" Dunnage 12 lbs. 2 $130.00

867-KDR148 48" 18" 12" Dunnage 14 lbs. 3 $145.00

Note: Most racks must ship via freight carrier. Please call for shipping quote. Movable

back stops available for keg racks. Custom sizes also available. Call for pricing.

867-KDR136


841-ICD-1000 Keg Spacer $29.95 $27.95

841-ICD-2000 Keg Stacker $25.95 $23.95

841-ICD-3000 Red Keg Dolly $39.95 $37.95

881-980 19" Diameter x 5" Thick Rubber Keg Bumper $99.95 N/A

Note: Spacers and stackers fit most straight wall 1/2 and 1/4 barrel kegs. Spacer fits most

coupler types. Some couplers may require a beer elbow fitting in order to avoid kinking

beer line. See page 31 for coupler fittings. All stackers, spacers and dollies come standard

in red. Keg bumper is black. Call for more information.

Keg Storage Accessories

Keg Storage Racks

841-ICD-2000841-ICD-1000

841-ICD-3000

881-980


867-KAR60

867-KSR72

76

Home Brewing Equipment


1 837-180777 S/S Cover Assembly (includes components 2 & 3a) $26.95 $24.95

2 837-180353-888 Relief Valve $9.95 $8.95

3a 815-536082 Lid "O" Ring $2.95 $2.25

3b 815-OS-536082 Oversized Lid "O" Ring $4.95 $3.95

4a 815-854201 "O" Ring (Ball Lock) $.68 $.51

4b 815-854501 "O" Ring (Pin Lock) $.68 $.51

5 837-180412 S/S Siphon Tube $12.95 $11.95

6 837-180426 Gas Tube $3.95 $3.55

7 837-180363 Gasket for Gas Tube & Siphon Tube $.68 $.51

1 2

3a,b

4a,b

5

6

7


Part Number Description 1-5 6 +852-PILGS-1 Pin Lock Gasket Set $4.95 $4.45852-BALGS-1 Ball Lock Gasket Set $4.95 $4.45

Pin Lock Set Includes: One #815-536082, Two #837-180363, Two

#815-854501

Ball Lock Set Includes: One #815-536082, Two #837-180363, Two

#815-854201


809-27-4242 Ball Lock Gas Disconnect with 1/4" Barb Fitting $6.25 $4.95

809-27-4243 Ball Lock Liquid Disconnect with 1/4" Barb Fitting $6.25 $4.95

809-27-4244 Ball Lock Gas Disconnect with 1/4" Male Flare Fitting $6.25 $4.95

809-27-4245 Ball Liquid Disconnect with 1/4" Male Flare Fitting $6.25 $4.95

809-720400 Pin Lock Gas Disonnect with 1/4" Barb Fitting (2 Slot) $6.95 $5.05

809-720401 Pin Lock Liquid Disconnect with 1/4" Barb Fitting (3 Slot) $6.95 $5.05

809-721400 Pin Lock Gas Disconnect with 1/4” Male Flare Fitting (2 Slot) $6.95 $5.05

809-721401 Pin Lock Liquid Disconnect with 1/4” Male Flare Fitting (3 Slot) $6.95 $5.05

822-PLD-100P Plastic Pin Lock Depressurizer Cap $3.25 $2.95

Note: See page 45 for swivel hose stem and nuts for male flare disconnects.


824-RC-5BL1 Reconditioned S/S 5 Gallon Ball Lock Product Tank Call For Availability

837-CK1-N5 New S/S 5 Gallon Ball Lock Product Tank $115.00 $105.00

870-CGP-411312 Chugger S/S Inline Brewing Pump $149.95 N/A

837-PCONV-BL3 Pin to Ball Lock Conversion Kit $15.50 $13.95

837-UP-ASSY Universal Poppet Assembly (Each) $2.95 $2.50


832-CMOXYW-16 16 oz. Pale of Craft Meister Oxygen Brewery Wash $17.95 $15.95

832-BTF-32 32 oz. Bottle of BTF Iodophor Liquid Sanitizer $15.50 $14.50

1 Available while supplies last. All reconditioned tanks are inspected for leaks and are

gaurenteed to hold pressure. Reconditioned pin lock tanks also available. Call for current

pricing and availability.2 Features a food grade, S/S head with 1/2” MPT inlet/outlet. Max flow of 7 GPM; Max head

of 18.6 ft. and can handle liquids up to 250°F. Includes 115V/60/1 Power Cord.3 Kit will convert any Firestone, Spartansburg or Hoover Pin Lock keg to a Ball Lock keg.

Includes 1- gas post, 1- liquid post, 2- universal poppet assemblies and “O” rings for each

post.

“O” Ring Sets

Replacement Product Tank Parts

Product Tank Disconnects

Product Tank Cleaning Chemical

Product Tanks & Components

837-PCONV-BL837-UP-ASSY

824-RC-5BL 837-CK1-N5

832-CMOXYW-16 832-BTF-32

809-27-4242

809-27-4244

809-720401

852-BALGS-1

870-CGP-41131


Soda & Wine Equipment


809-0501567-01A Adapter for #QCD-11, #PCS1 & #PCSS BIB Connectors $2.50

809-20-1110-20 Adapter for #P37SBBKHN BIB Connector $6.95

809-PCS1 Bag-In-Box Connector (Pepsi & General Beverage) $6.95

809-PCSS Bag-In-Box Connector (Pepsi & General Beverage) $7.50

809-QCD-11 Bag-In-Box Connector (Pepsi & General Beverage) $6.95

809-P37SBBKHN Bag-In-Box Connector (Coca-Cola) $5.95

Note: All Bib Connectors and Bib Adapters have 3/8” Barbs


809-E4000397 McCann's High Volume Carbonator with Vent Check and 115V Power Cord $435.95

803-FTV-121 Heavy Duty Self-Piercing Water Saddle Valve $21.95

809-263A2 0-125 psi Water Regulator Body Only $69.95

807-104-7 0-160 psi Liquid Filled Gauge $22.65

809-50003 Flo-Jet 5000 CO2 Driven Syrup Pump with Fittings $46.95

809-1510-000 CO2 Disconnect Shut-Off for #5000 Flo-Jet Syrup Pump $4.25

809-20324-030 1/4" Barbed Fitting for #5000 Flo-Jet Syrup Pump $3.95

809-1500 Flo-Jet Automatic BIB Transfer Valve $19.95

809-111841 Scholle "T" Fitting $6.95

809-111842 Scholle "L" Fitting $6.951 Fits 1/2”-7/8” OD Copper tubing or 3/4” OD Stainless Steel tubing.2 Has two 3/8” FPT ports for fittings and one 1/4” FPT port for water gauges.3 Includes 1/4” barbed fitting for Gas in/out and 3/8” barbed for syrup. Other barb sizes available.

Note: Other soda equipment and BIB cleaning attachments available. Please call for information.


801-660W Plastic Cornelius Wine Faucet $29.95

810-630SS Perlick 630 Series 304 S/S Faucet with Stainless Lever $44.95

808-VSQTSS Vin Service Quix Tap 304 S/S Faucet with Stainless Lever $49.95

810-36000GS Perlick US Coupler with 304 S/S Probe $44.95

803-481 3" x 3" x 1/4" Aluminum Underbar Mounting Bracket with 1" Hole $6.95

801-SS-1364B 4" Long x 1/4" Bore 304 S/S Shank Assembly $21.95

Wine Equipment

Soda Dispensing Equipment

Soda Bag-In-Box Connectors

801-660W

810-630SS808-VSQTSS 803-481

810-36000GS

801-SS-1364B

809-E4000397

803-FTV-12 809-263A

809-5000

809-1500

809-20324-030

809-111841 809-111842

809-0501567-01A 809-20-1110-20

809-PCS1809-QCD11

809-PCSS809-P37SBBKHN

Note: 304 Stainless Steel Shanks available in other sizes. See page 32. Wine dispensing towers,

trunk lines and flash chillers also available. Please call for more information.

807-104-7

78

Cleaning Equipment



800-934 Sankey Threaded Double Flusher $76.95

800-938 Sankey Threaded Single Flusher $29.50

800-109S Double Flusher Adapter with Female Threads $21.95

810-43657 Perlick Single Cleaning Adapter with Male Hex Threads $33.95

810-43681 Perlick Double Cleaning Adapter $36.95

810-43659 Perlick Series Cleaning Adapter (Threads on to #810-43657 Adapter) $29.95

800-CC401L Black Plastic Series Cleaning Cup $6.95

800-85-117 Coupler Ball Lifter $2.95

Note: Sankey flushers work with both US and European style couplers. Perlick flushers for

imported keg couplers also available. Please call for more information.

Cleaning Adapters

Cleaning Attachments

Note: Straight Cleaning Attachment Jumper comes with two 801-254 cleaning attachments, two

801-753 washers, 2 ft. of clear 5/16” vinyl tubing and clamps. May be ordered with longer tubing

at additional charge. Call for pricing.


801-254 Straight Cleaning Attachment with 5/16" Hose Barb $5.25

801-753 Rubber Washer for #801-254 Cleaning Attachment $.25

808-IDEUR-CLEAN-1/2 1" Long x 1/2" Euro to US Cleaning Adapter $25.95

808-EURO-CLEAN European Cleaning Adapter with 3/8" Hose Barb $17.95

807-4352T Threaded Cleaning Attachment (Faucet Thread x Beer Thread) $14.95

852-254-2KIT Straight Cleaning Attachment Jumper $10.95

801-252 Duplex Coupling (Beer Thread x Beer Thread) $10.75

801-132 3/8" Bore Beer "Y" with Hex Nut $16.50

801-4132-252 Four #801-132 Beer “Y” and One #801-252 Duplex Coupling $72.50

805-GH58 Garden Hose Coupling with 5/8” Barb and Rubber Washer $3.25


803-SS-BMC-8 8 Way Beer Threaded Cleaning Manifold (19" Long) $59.95

802-SS-BMC-8-SH 8 Way Beer Threaded Cleaning Manifold (9-1/2" Long) $42.95

802-SS-CM-6 6 Way Beer Threaded Line Coupler $36.95

800-FT874C Hex Nut Cap and Washer $5.95

Line Cleaning Manifolds

800-934800-938

800-109S

810-43657810-43681

810-43659 800-CC401L

800-85-117

801-254

801-753

808-IDEUR-CLEAN-1/2 808-EURO-CLEAN 807-4252T

852-254-2KIT

801-252 801-132

803-SS-BMC-8

802-SS-BMC-8-SH

803-SS-CM-6

800-FT874C

805-GH58

79

Cleaning Equipment

KIT INCLUDES:

- 2 qt. Plastic Jar and Pump Assembly

- #801-1350 Faucet Wrench

- #818-1329-34 Faucet Brush

- #832-BLC-04 4 oz. Bottle of BLC Liquid Cleaner (#832-BLC-32

32 oz. Bottle of BLC Liquid Cleaner with #852-EDCK-32)

- #800-85-117 Coupler Ball Lifter

- 2 ft. of 5/16” Clear Vinyl Beer Line with #801-254 Straight Cleaning

attachment and an #801-753 Rubber Washer

- Instruction Manual

Note: 852-EDCK-32 also includes an #800--904A 4 ft. x 3/16” hose brush


852-EDCK-2 Complete Economy Cleaning Kit with 4 oz. BLC $25.95 $20.95

852-EDCK-32 Complete Economy Cleaning Kit with 32 oz. BLC $32.95 $27.95


800-1841 Complete Deluxe Cleaning Kit $54.95

KIT INCLUDES:

- 1 qt. Plastic Jar and Deluxe Pump Assembly

- #800-904A 4 ft. x 3/16” Hose Brush

- #801-1350 Faucet Wrench

- #818-1329-34 Faucet Brush

- #832-BLC-04 4 oz. Bottle of BLC Liquid Cleaner

- #800-85-117 Coupler Ball Lifter

- 2 ft. of 5/16” Clear Vinyl Beer Line with #801-254 Straight Cleaning

attachment and an #801-753 Rubber Washer

- Draft Beer Fact Book

*Includes any combination of 4 cleaning valves. Valves are not removable

once installed. Please specify desired valves when ordering.

Note: Stainless Steel valve(s) must be purchased separately and will screw

directly into female threads included on top of 806-CP-13-CO cleaning can.


806-LCT420* 4.8 Gallon, 4 Valve Stainless Steel Cleaning Can $395.95

806-CP-13-CO 1.3 Gallon, 1 Valve Heavy Duty Plastic Cleaning Can $72.95

806-CB-005 "D" Type Stainless Steel Valve with Down Tube $44.95

806-CB-003 "S" Type Stainless Steel Valve with Down Tube $44.95

806-CB-002 "G" Type Stainless Steel Valve with Down Tube $44.95

806-CB-001 "A" Type Stainless Steel Valve with Down Tube $44.95

806-CB-006 "U" Type Stainless Steel Valve with Down Tube $47.95


808-CP151130 "D" System Cleaning Socket $29.95

808-CP151132 "S" System Cleaning Socket $27.95

808-CP151133 "U" System Cleaning Socket $27.95

808-CP151134 "A" System Cleaning Socket $27.95

808-CP151135 "G" System Cleaning Socket $27.95

808-CP151140 Back Plate $9.95

808-CP151142 End Stop Cap $2.95

808-CP151100 S/S Mounting Board with Handle $92.00

806-LCT420

Economy Cleaning Kits

Deluxe Cleaning Kits

Stainless Steel & Plastic Cleaning Cans

In-Place Portable Cleaning

806-CP-13-CO

806-CB-005 806-CB-003

806-CB-002 806-CB-001

806-CB-006

808-CP151130 808-CP151132 808-CP151135

808-CP151133 808-CP151134 808-CP151140

808-CP151142808-CP151100Note: Each cleaning socket requires a back plate in order to be mounted.


80

Electric Cleaning Pumps


835-IP321 Little Giant Light Duty Submersible Cleaning Pump Assembly $195.00

863-JS3002 Maxi-Vac Medium Duty Electric Cleaning Pump Assembly $475.00

807-ECC-1003 Armstrong Heavy Duty Electric Cleaning Pump Assembly $955.951 Little Giant Submersible Pump has an epoxy coated aluminum casing, nylon pump head and im-

peller and a thermal overload protector. 1/15 HP motor pumps 185 gallons per hour at a 6 ft. rise.

Assembly comes with 6 ft. of 1/2” ID tubing, #834-205S threaded pump adapter and an #801-254

straight cleaning attachment with rubber washer. Other tubing sizes available.2 Maxi-Vac electric pump is designed for use with direct draw and short run systems. Self-priming

duplex diaphragm pump may run dry indefinitely without damage to pump. Assembly comes with

an internal recirculating by-pass that will protect system from excessive pressure and has a 1.5

Gallon Per Minute flow rate, up to 60 PSI. Assembly comes standard with a suction and pressure

hose with fittings, adapters and quick disconnects. Pump is resistant to acid based cleaners.

Maxi-Vac heavy duty pump assembly also available. Call for pricing.3 Armstrong electric pump is designed for long distance runs and features an adjustable pressure

control. Unit comes equipped with sight glass and pressure gauge, 6 ft. of suction hose and 6 ft.

of pressure hose with fittings and adapters. Assembly has a durable powder-coated case and is

corrosion resistant. Pump handles up to 240 Gallons Per Hour at 150 PSI. Pump runs off a 1/3 HP

motor. Pump is gear driven. Please note that bronze gears will corrode with acid based cleaners

over time. Plastic gears are more resilient to acid based cleaners. Please call for more information.


1 807-104-1 1/3 HP Motor, 115V $168.66

2 807-104-1E Toggle Switch $12.95

N/A 807-104-1E1 Switch Mounting Box $14.16

N/A 807-104-1E2 Switch Box Cover Plate $6.85

3 807-104-1B 115V Cord Only $12.95

4 807-104-4ASSY Sight Glass Assembly $69.95

5 807-104-3 Aluminum Base $47.95

6 807-104-3A Rubber Feet (Each) $1.75

7a 807-104-2 Pump Complete with Bronze Gears $299.50

7b 807-104-2PPS Pump Complete with Plastic Gears $290.50

8a 807-104-5C6S 6 ft. Suction Hose Only $17.50

8b 807-104-5C8S 8 ft. Suction Hose Only $19.50

9 807-104-5B Suction Strainer Assembly $43.50

N/A 807-104-5B1 Suction Strainer Fitting Body $10.75

N/A 807-104-5B2 Suction Strainer Collar Nut $21.25

N/A 807-104-5B3 Suction Strainer Screen $12.75

10a 807-104-5C6P 6 ft. Pressure Hose Only $16.95

10b 807-104-5C8P 8 ft. Pressure Hose Only $19.50

10c 807-104-5C12P 12 ft. Pressure Hose Only $25.10

11 807-4352T Threaded Cleaning Attachment $14.95

12 807-104-7 Liquid Filled Pressure Gauge $22.65

13 807-104-6 By-Pass Valve $15.25

14 807-104-2E Pump to Motor Bracket $89.50

15 807-104-8 Handle $23.65

16 807-104-110 Sponge Kit $4.90

17 801-24R Rubber Washer (Each) $.30

N/A 801-252 Double Male Threaded Connector $10.75


1

23

4

56 7a

8a

9 10a

11

12

13

14

15

16 17

1819

19

20

21

22 23

23

24

24

25

26a,29a 27

28

26b,29b

26c


18 807-104-2G Spider $6.95

19 807-104-2F Half Coupling $16.15

20 807-104-2H Screw $3.50

21 807-104-2B Seal $17.20

22 807-104-2J Cover Casting $104.75

23 807-104-2D Carbon Bearings $16.25

24 807-104-2A1 Retaining Ring $7.10

25 807-104-2A2 Drive Shaft Only $20.20

26a 807-104-2A3 Plastic Gear $43.75

26b 807-104-2AP1 Plastic Drive Gear Assembly $67.60

26c 807-104-2AP2 Plastic Idle Gear Assembly $47.25

27 807-104-2A4 Key $5.40

28 807-104-2A5 Idle Shaft Only $23.95

29a 807-104-2AB1 Bronze Drive Gear Assembly $51.25

29b 807-104-2AB2 Bronze Idle Gear Assembly $47.25

30 807-104-2C Paper Gasket (Older Models) $1.80

31 807-104-2O "O" Ring (Newer Models) $10.50

32 807-104-2K Body Casting $76.50

33 807-104-2M Screw (Each) $3.20

34 807-104-4A Pyrex Glass $8.95

35 807-104-4B Gasket (Each) $2.95

36 807-104-4C Brass Screen $5.20

37 807-104-4D Casting Set $57.25

30,31

32 33

3435

35

36 37

37807-ECC-100

863-JS300

835-IP32

81

Cleaning Equipment

No. Part Number Description Dimensions 1-11 12 +

1 818-FVHB-1-18 Faucet Vacuum Hole Nylon 1/8" Diameter x 4" Long $2.95 $2.75

2 818-SPB-1-932 Shank & Probe Nylon 9/32" Diameter x 6" Long $1.95 $1.75

3 818-SPB-1-38 Shank, Probe & Faucet Lever Nylon 3/8" Diameter x 6-5/16" Long $1.95 $1.75

4 818-1329-12 Faucet Spout & Lever Nylon 1/2" Diameter x 8-1/2" Long $1.95 $1.75

5 818-1329-34 Faucet Spout & Lever Nylon 3/4" Diameter x 8-3/4" Long $1.95 $1.75

6 818-SS-1329-58 Faucet Spout & Lever S/S 5/8" Diameter x 9" Long $2.95 $2.65

N/A 818-1329-34W Faucet Spout & Lever White Nylon 3/4" Diameter x 8-3/4" Long $2.15 $1.95

N/A 818-BRUSH-SET - - $18.95 N/A

7 800-904A Hose Brush Nylon 3/16" Diameter x 66" Long $4.95 $4.25

N/A 800-904B Hose Brush Nylon 1/4" Diameter x 66" Long $4.95 $4.25

8 800-904C Hose Brush Nylon 3/8" Diameter x 66" Long $5.15 $4.45

818-BRUSH-SET INCLUDES:

818-FVHB-1-18

818-SPB-1-932

818-SPB-1-38

818-1329-12

818-1329-34

818-SS-1329-58

800-1350C

KEY RING

Note: Other replacement brushes available. Brushes with pinned bases are exclusive to Bar

Maid electric glass washers and will not work with any other brand. Slotted Based brushes

are Universal brushes and will work with most brands except Waring. Add suffix “-SL” for

slotted universal brushes when ordering. Please call for more specifications and details.

Part Number Description Pinned Slotted

872-BRS-732SG Replacement Shot Glass Brush $23.75 N/A

872-BRS-917 Replacement 6" Brush (Standard Glasses) $14.25 $14.25

872-BRS-922 Replacement 7-1/2" Brush (Taller Glasses) $16.25 $16.25

872-BRS-930 Replacement Coffee Pot & Pitcher Brush (Wide Pots/Pitchers) $22.75 N/A

872-BRS-935 Replacement Coffee Pot Brush (Narrow Top Pots) $22.75 N/A

872-BRS-950 Replacement Margarita Brush (Margarita & Martini Glasses) $18.55 N/A

872-BRS-976 Replacement 9" Pilsner Brush $21.45 $21.45

1 A200 Washer features a quiet, powerful 1/3 HP enclosed motor with sealed lower bear-

ing and exclusive splashgard canopy. Heavy Bronze bearings and stainless contruc-

tion. 115V-60Hz. 220V,50/60Hz models also available.2 SS100 Washer features a powerful 1/3 HP motor, heavy-duty stainless construction

and bronze bearings deliver outstanding performance and reliability. G.F.C.I included.

115V-60Hz. 220/230V-50/60Hz models also available.


872-A200 Upright Electric Glass Washer with 5 Brush Heads $352.00

872-SS100 Submersible Electric Glass Washer with 5 Brush Heads $465.00

873-MTB-100 Manual Glass Washer with 3 Brush Heads $12.45

873-MTB-RB Replacement Brush Head for Manual Washer $3.95


123456

7 8

Cleaning Brushes

Electric & Manual Glass Washers

Replacement Glass Washer Brushes

872-A200

872-SS100

873-MTB-100

873-BRS-917-SL 873-BRS-922-SL 873-BRS-930873-BRS-930 873-BRS-950 873-BRS-976-SL

82

Cleaning Chemical

Note: All cleaners and tablets available in larger quantities. Liquid cleaners available in 5 gallon, 15 gallon

and 55 gallon containers. Please call for pricing and shipping information. Special case pricing available

for large quantity orders. Call for details.

Which Cleaner to Choose?Beverage Line Cleaner (BLC) : Alkaline based line cleaner easily loosens beer stone, biomass, organics, and mineral deposits from draft

system. Designed for direct draw systems, cooler boxes (coil & cold plate) or any SHORT run system. Effective at only 1/2 oz. per quart ofwater.

Penetrate Beverage Line Cleaner (PEN) : Powerful alkaline based line cleaner easily loosens and suspends soils embedded in beer

lines. Ideal for very long draw, glycol-cooled, and neglected or older draft line systems. Brewery approved at only 1 oz. per gallon of water.

Double Alkaline Draft Line Cleaner (DAC) : Twin-Alkaline formula penetrates embedded residue on heavily soiled, case hardened,

and problematic beer lines. High quality surfactants suspend soils and improve rinsability. Ideal for very long draw, glycol-cooled, and neg-lected or older draft line systems. Brewery approved at only 1 oz. per gallon of water.

Clear-Tap Beer Line Cleaner (CTAC) : Alkaline based line cleaner with a colored rinse indicator allows you to see your cleaning has

been safely completed. Food-safe dyes are formulated into Clear-Tap and not just as a secondary additive. Easily removes beer stone, biomass,organics, and minseral deposits from beer lines. For use with both short and long draw systems.

Acid Post Wash Line Cleaner (ALC) : Removes calcium oxalate buildups that other beer line cleaners leave behind. Use ALC as part of a

regular cleaning rotation (roughly every 6 cleanings) on draft lines with specialty brews, imports, and beers using high calcium brewing water.Effective at only 1 oz. per gallon of water.

Wine Line Cleaner (WLC) : A special blend of chemicals and surfactants that target and remove wine molds, yeast, tannins, residues, and

tartrate deposits. Helps maintain the true taste of kegged wine. Also greate for cleaning vats, bottles and small parts used in making wine andmead. Effective with only 1 oz. per gallon of water.

AllKlear Rinse Indicator (ALLKLEAR) : Rinse indicator additive that lets you know when your line cleaning work has been safely com-

pleted. Safety color any acid or alkaline cleaner mentioned above with a certified food-safe indicator.

Super No-Rinse Beverage System Cleaner (SNR) : Alkaline-based powdered beer line cleaner for short beverage systems and brew-

ing equipment. Easily removes beer stone, biomass, organics, and mineral deposits from short-run draft systems. No need to flush with water;use the beverage to push out chemical solution at end of cleaning cycle.

Powdered Line Cleaner (PLC) : Economical powder for cleaning draft systems includes a colored rinse indicator that lets you see when

your cleaning has been safely completed. Alkaline formula removes naturally occurring build-ups in beer lines, parts and fittings. Quicklycleans plastic, stainless steel, brass, copper, nickel and rubber without damage. No need to flush with water; use the beverage to push outchemical at end of cleaning cycle.

Powdered Wine Line Cleaner (WLC) : A special blend of chemicals and surfactants that target and remove wine molds, yeast, tannins,

residues, and tartrate deposits. Helps maintain the true taste of kegged wine. Also greate for cleaning vats, bottles and small parts used inmaking wine and mead. No need to flush with water; use the beverage to push out chemical at end of cleaning cycle.


832-BLC-04 4 oz. Bottle of BLC Beverage System Cleaner $2.50 $2.25832-BLC-32 32 oz. Bottle of BLC Beverage System Cleaner $8.95 $7.95832-PEN-32 32 oz. Bottle of Penetrate Beverage Line Cleaner $9.95 $8.25832-DAC-32 32 oz. Bottle of DAC Draft Line Cleaner $10.95 $9.50832-CTAC-32 32 oz. Bottle of Clear-Tap Beer Line Cleaner $9.95 $8.25832-ALC-32 32 oz. Bottle of ALC Acid Post Washer for Draft Lines $9.95 $8.25832-WLC-32 32 oz. Bottle of WLC Wine System Cleaner $9.95 $8.25832-ALLKLEAR-50 50 Count Jar of AllKlear Rinse Indicator Tables $4.95 $4.50832-SNR-3 3 lb. Tub of Super No-Rinse Beverage System Cleaner $14.50 $13.00832-SNR-420 40 lb. Tub of Super No-Rinse Beverage System Cleaner $104.95 $94.95832-PLC-3 3 lb. Tub of PLC Beverage System Cleaner $14.95 $13.50832-PLC-420 40 lb. Tub of PLC Beverage System Cleaner $108.95 $98.95832-WLC-3 3 lb. Tub of Powdered WLC Wine System Cleaner $14.50 $13.00


83

Cleaning Chemical


832-BTF-32 32 oz. Bottle of BTF Iodophor Sanitizer $15.50 $14.50

832-BTF-1675 16.75 oz. Jar of BTF Chloromelamine Sanitizer $13.95 $11.95

832-BTF-100 100 Count Case of BTF Sanitizer Powder Packets $19.95 $17.65

832-TDC-32 32 oz. Bottle of TDC Liquid Detergent (Manual Brushes) $8.95 $7.95

832-TDCTAB-100 100 Count Jar of TDC Detergent Tablets $18.95 $16.95

832-TDC-25 25 oz. Jar of TDC Powder Detergent $10.50 $8.50

832-TDC-100 100 Count Case of TDC Powder Detergent Packets $18.95 $16.95

832-LFD-25 25 oz. Jar of LFD Powder Detergent (Electric Brushes) $9.95 $8.95

832-LFD-100 100 Count Case of LFD Powder Detergent Packets $18.95 $16.95

Glass Washing Detergent & Sanitizer


832-IMC-16 16 oz. Bottle of Ice Machine Cleaner $7.95 $6.95

832-DBC-32 32 oz. Bottle of DBC Mineral and Lime Solvent $10.50 $9.50

832-BTFQA-32 32 oz. Bottle of BTF QA Sanitizer, Disinfectant & Deodorizer $8.95 $7.95


832-CMALKW-16 16 oz. Jar of Craft Meister Alkaline Brewery Wash $17.95 $15.95

832-CMOXYW-16 16 oz. Jar of Craft Meister Oxygen Brewery Wash $17.95 $15.95


849-DT-BBLC 32 oz. Bottle of Draftec Beer Line Cleaner with Blue Tracer $8.25 $6.95

849-DT-RALC 32 oz. Bottle of Draftec Acid Line Cleaner with Red Tracer $8.25 $6.95


Note: All Draftec products available in larger quantities. Liquid cleaners available in 5 gallon and

55 gallon containers. Please call for pricing. Free base shipping on pallet orders to a commercial

address. Four 55 gallon containers, twenty seven 5 gallon containers or fifty two cases of 12 - 32

oz. bottles. Products on pallet can not be mixed. Free freight does not include hazardous material

fee, lift gate or call ahead service. Please call for more information.

Ice Machine Cleaner & Sanitizer

Home Brewing Equipment Cleaner

Draftec Beer Line Cleaner

Fast-acting oxygen tears up soils in just minutes with little agitation needed. Formulated

to combat calcium carbonate. Cleans brew kettles, corny kegs, fermentors, fittings, tubing

and bottles. Alkaline wash combats calcium carbonate and oxalate residues left behind by

Oxygen wash and will not burn skin or damage stainless steel.

BTFQA-32 is an all purpose sanitizer, disinfectant, and deodorizer. Concentrated quaternary ammonium

formula for use on most hard, nonporous surfaces; used to sanitized ice machines. DBC-32 is an all

purpose cleaner for use on bar sinks, faucets and ice machines. Safe for use wth glass, aluminum,

baked on enamel, chrome, stainless steel, vinyl and tile surfaces. IMC-16 is a nickel-safe formula that

removes lime scale, hard water build up and algae growth from holding tanks, cooling trays and slides.

BTF products for sanitizing all brewing equipment: kettles, pails, tanks, vats, bottles and more. TDC

detergents are for use with manual washing or stationary brushes. LFD detergents are for use with

electric brushes.

84

Hand Carts

A

Han

dle

s

B

C

Fra

mes

No

se P

late

sChoose One Component Each from A, B, C, D + Accessories from E + Completion Pack from F

NoteFully assembled carts MUST

Ship via Freight Carrier. Save

Money on Shipping by

Purchasing Cart(s) knocked

down in box complete with

assembly instructions.

Knocked down cart(s) will ship

UPS.


804-A1 Standard Loop, 52" Overall Height $16.95

804-A2 Standard Loop, 52" Overall Height with #E45 U-Brace $20.95

804-A3 Straight Loop, Single Grip at 46", 52" Overall Height $30.75




804-A7 Straight Loop, Vertical Grip, 52" Overall Height (for use with #B1, #B3, #B6 & #B7 frames) $34.25

804-A10 Straight Loop, Vertical Grip, 52" Overall Height (for use with #B4 & #B5 frames) $33.25

804-A11 Standard Double Grip with #E45 U-Brace, 48" Overall Height $24.50

804-A12 Straight Loop, Single Grip, 52" Overall Height $24.50

804-A13 Standard Loop with Comfort Sleeve, 52" Overall Height $16.50

804-A14 Standard Loop with Comfort Sleeve, 52" Overall Height with #E45 U-Brace $24.50

804-A16 Double Grip, Loops at 43-5/8", 60" Overall Height $40.50


804-B1 Standard Straight Back $46.95

804-B3 Straight Back with 2 Vertical Strap Bars $58.25

804-B4 Curved Back, 1 Vertical Strap Bar $76.75

804-B5 Curved Back $58.50

804-B7 Combination Back, 1 Straight Bar, 2 Curved Bars $57.95


804-C1 Recessed Heel with Cut-Outs (14" W x 7-1/2" D) $44.90

804-C2 Recessed Heel with Cut-Outs (18" W x 7-1/2" D) $52.50

804-C3 Rear Mount (14" W x 7-1/2" D) $48.50

804-C5 Rear Mount (18" W x 7-1/2" D) $53.90

804-C6 Front Mount (18" W x 9" D) $48.25

804-C8 Front Mount (16" W x 12" D) $63.75

804-C9 Front Mount (20" W x 12" D) $70.25

804-C19 Recessed Heel, No Cut-Outs (14" W x 7-1/2" D) $44.50

804-C20 Recessed Heel, No Cut-Outs (18" W x 7-1/2" D) $51.50

804-CA1* Recessed Heel with Cut-Outs (14" W x 7-1/2" D) $35.75

804-CA2* Recessed Heel with Cut-Outs (18" W x 7-1/2" D) $45.50

*Made of Cast Aluminum. All other nose plates constructed of Extruded Aluminum.

Note: Cast Aluminum nose carry a 1 Year Warranty, all other parts carry 2 Year Warranty.


804-A1 804-A2 804-A3 804-A7

804-A11

804-A12804-A13

804-A14

804-A15

804-B1 804-B3 804-B4 804-B5 804-B7

804-C1 804-C2 804-C3 804-C5 804-C6

804-C19 804-C20

804-CA1 804-CA2

85

Hand Carts

E

Acce

ssorie

s

FCo

mp

letio

n P

ack

s

DWh

eels

Part Number Description Each Set of Two

804-D5 10" x 3-1/2" 4 Ply Pneumatic with Inner Tube, 2 Piece Steel Hub, Precision Bearing, 600 lb. Capacity $32.00 $64.00

804-D5S 10" x 3-1/2" 4 Ply Sawtooth Polyurethane Filled Tire, 3 Piece Steel Hub, Precision Bearing, 600 lb. Capacity $37.00 $74.00

804-D6 10" x 3" Carefree Solid Foam Filled, 1 Piece Steel Rim, Non-Marking, Precision Bearing, 600 lb. Capacity $36.95 $73.85

804-D6SS 10" x 3" Super Carefree Solid Foam Filled, Polypropylene Hub, Non-Marking, Precision Bearing, 600 lb. Capacity $32.25 $64.50

804-D12 8" x 1-5/8" Rubber on Aluminum Offset Hub, 600 lb. Capacity (requires short axle) $20.50 $41.00

804-D15 10" x 2-1/8" Balloon Cushion, High Impact Polypropylene Hub, Precision Bearing, 600 lb. Capacity $24.25 $48.50

804-D16 8" x 2-1/8" Ballon Cushion, High Impact Polypropylene Hub, Precision Bearing, 600 lb. Capacity $21.25 $42.50


804-E13 Aluminum Kick Bar for #E1L Stair Climbers $8.60804-EIL Set of Two Extruded Aluminum Stair Climbers with 1/2" Wear Strips (includes mounting hardware) $41.50804-E45 45" Frame Extension $5.50804-E52 52" Frame Extension $11.30804-E55 55" Frame Extension $17.85804-E60 60" Frame Extension $20.95804-E68 68" Frame Extension $20.95804-E9 Beer Keg Hook for Sankey Type 1/2 Barrels (includes mounting hardware) $28.50


804-F1 Completion Pack for All Models Except Carts with #D12 Wheels $32.50

804-F2 Completion Pack for #D12 Wheel Carts $32.50

F1 PACK includes wheel brackets (left & right), side channel reinforcements, long axle,

washers, bolts, nuts, cotter pins, roll pins and assembly instructions.

F2 PACK includes all items listed above, but with short axle for #D12 wheels.

Replacement Parts & Hardware


804-RH-BRACKET Right Hand Wheel Bracket $9.20

804-LH-BRACKET Left Hand Wheel Bracket $9.20

804-AXLE-SHORT 16-13/16” Axle $8.30

804-AXLE-LONG 18” Axle $7.75

804-AXLE-PT-PK 2 Cotter Pins, 2 Roll Pins and 8 Thin Washers $2.00

804-COTTER-PIN Axle Cotter Pin $.35

804-ROLL-PIN Axle Roll Pin $.35

804-WASH-THIN Thin Axle Washer $.45

804-WASH-THICK Thick Axle Washer $.45

804-NOSE-PACK Bolt Package for Nose Plates $2.15

804-IN-TUBE D5 Inner Tube $7.25

804-MOUNT-KIT Mounting Kit for C3, C5, C8 & C9 Nose Plates $10.50


804-E1-SKID-15 15" Wear Skid for #E1L Stair Climber $4.25

804-E1-SKID-15-2 Two 15" Wear Skids for #E1L Stair Climber $12.10

804-E1-SINGLE Single #E1 Stair Climber $20.75

804-E1-FP Fastener Pack for #E1L Stair Climber $4.95

804-HDLP-L 2" Handle Bolt Pack $1.55

804-HDLP-S 1-3/4" Handle Bolt Pack $1.55

804-A11-RH Right Hand Single Grip $8.75

804-A11-LH Left Hand Single Grip $8.75

804-HDLGP-RD Red Handle Grip Only $3.50

804-HDLGP-BK Black Handle Grip Only $3.50

804-CHL-SIDE Side Channel Reinforcement (all frames) $4.65

804-PWB-58 Precision Wheel Bearing $4.25


804-F1

804-E13

804-E1L 804-E52 804-E60 804-E68 804-E9

804-D5 804-D5S 804-D6 804-D6SS 804-D12 804-D15 804-D16

804-E55

86

Installation & Maintenance Tools

Part Number Description 1-11 12 +801-1350 Spanner Wrench with Red Grip $2.95 $2.75801-1350C Spanner Wrench w/ Hole $3.05 $2.85801-FT-1000 Faucet and Hex Nut Wrench $14.95 $13.65800-FT-1000-3 Faucet and Hex Nut Wrench & Screwdriver $9.95 $9.25800-FT-8612 Hex Nut and Probe Wrench $8.50 $7.95800-D4740-W Tower Wrench Set (includes 2 wrenches) $16.95 $14.95810-BMW-1 Perlick Beer Mechanic Wrench $19.00 N/A810-32474-1 Perlick Hex Nut and Probe Wrench $9.95 $9.25808-1350SP Heavy Duty Spanner Wrench $10.95 $10.25

Part Number Description Each835-HD-1331 Heavy Duty Hose Cutter with Lock/Unlock Button $25.95801-1331 Black Plastic Hose Cutter with Blade $5.95801-1331-1 Replacement Blade for #801-1331 Hose Cutter $2.50802-2401 Straight Jaw Crimpers $16.95802-2400 Side Jaw Crimpers $19.95835-ID-SIZER-TOOL ID Sizer Tool for 3/16", 1/4", 5/16", 3/8", 1/2" & 3/4" Tubing $16.25835-STD-09 Number Tape Dispenser with 0-9 Digits $49.95835-STD-REF-X* Replacement Number Roll for #835-STD-09 Dispenser $3.95847-CC-125 Conduit Clamp $.30816-TS10-58 5/8” Self Tapping Screw $.10835-CT-6 6” Cable Tie $.10821-SMCT-6 6” Screw Mount Cable Tie $.12821-SMCT-15 15“ Screw Mount Cable Tie $.4330150 1" Dial Thermometer (0°F-220°F) $7.9586-DT302 Digital Thermometer (-50°F-392°F) $12.9530301 Refrigerator/Freezer Dial Thermometer with Hanging Clip (-20°F-80°F) $4.95*Specify number (0-9) in place of X when ordering.


Beer Wrenches

Installation Tools & Thermometers

Testing Supplies, Indicators and Fruit Fly StripsPart Number Description Each

832-PH-0114 50 Strip Solution PH Test Kit (0-14 PH Test Range) $11.95

832-QT-10 15 Strip QA Test Kit (Measures Alkyl Dimethyl Benzyl Ammonium Cloride in solution - C12-C16) $2.95

832-PCTK-100 100 Strip Precision Chlorine Test Kit (Measures Concentration of Chlorine in Solution) $5.95

832-PITK-100 100 Strip Precision Iodine Test Kit (Measures BTF Iodophor Solution for Proper Dilution) $5.95

104-FFBP-1 Individual Fruit Fly Bar Pro Strip $7.15

104-FFBP-10 Case of Fruit Fly Bar Pro Strips (10 Strips per Case) $65.00

801-1350

801-1350C

808-1350SP

801-FT-1000

800-FT-1000-3

800-FT-8612

810-BMW-1

810-32474-1

835-HD-1331

801-2401

801-2400801-1331801-1331-1

835-STD-09

835-ID-SIZER-TOOL

86-DT302

30150

30301

832-PH-0114

104-FFBP-1

805-SMCT-6 847-CC-125

816-TS10-58

800-D4740-W

832-QT-10

832-PCTK-100 832-PITK-100

87

Repair Kits & Keg Master List

Part Number Description 1-5 6 +800-T740SN60 Taprite 0-60 psi Regulator Body Only $28.75 $27.75800-T1660SN60 Taprite 0-60 psi Secondary Regulator Body Only $26.75 $25.95801-B800C-60 Cornelius 0-60 psi Primary Regulator Body Only $29.95 $28.95801-3060S Cornelius 0-60 psi Secondary Regulator Body Only $27.75 $26.95800-7740-15* Repair Kit for Taprite CO2 Primary & Secondary Regulators $9.95 $9.45800-7740-15N Repair Kit for Taprite N2 Primary Regulators $9.95 $9.45801-RK-800C Repair Kit for Cornelius Primary Regulators $11.95 $11.25801-RK-802C Repair Kit for Cornelius Secondary Regulators $13.45 $12.95800-440-4PN Taprite Regulator Seat Cartridge Wrench $10.95 $10.25801-RK-660B 660B Faucet Repair Kit with Spanner Wrench $5.85 $5.25

*Repair kit works with both Metal Bonnet and Polycarbonate Bonnet style Taprite regulators.

Regulator & Faucet Repair Kits

800-7740-15 801-RK-800C 800-440-4PN

801-RK-660B

Abbot Ale........................................... GAbby White........................................ UAbita (All Brands)............................. DAlaskan............................................... DAmstel (All Brands)........................... SAnchor Steam.................................... GAnderson Valley................................ DAvery (All Brands)............................. DAyinger (All Brands)......................... ABad Frog............................................. DBass Ale.............................................. DBavik Pilsner...................................... ABay Hawk........................................... DBBC (All Brands)................................ DBeamish/Scottish Newcastle........... SBecks.................................................. DBelhaven............................................ SBelle-Vue............................................ SBitburger Pilsner............................... ABlackthorn Cider............................... GBlue Moon......................................... DBoddington's..................................... GBreckenridge..................................... DBrooklyn (All Brands)....................... DBruin Pale Ale.................................... DBudweiser (All Brands)..................... DBusch (All Brands)............................. DCaffrey's............................................. GCantillon Rose................................... SCarlsberg............................................ AChimay............................................... ACider Jack........................................... DClipper City Heavy Seas................... DColumbia Brewing............................ DCoors (All Brands)............................. DCorsendonk....................................... SCustom Brewcrafters........................ DDe Dolle............................................. ADelirium............................................. ADevil Mountain................................. DDogfish Head..................................... DDos Equis........................................... DDouble Diamond............................... SEel River............................................. DEllicottville......................................... DFat Tire............................................... DFischer................................................ AFirehouse........................................... DFirestone............................................ DFlying Dog......................................... DFoster's............................................... DFull Sail............................................... DFuller's................................................ G

Genesee (All Brands)......................... DGooseland........................................... DGordon Biersch................................... DGrants.................................................. DGreat Divide........................................ DGrolsch................................................ GGuinness Stout................................... UHacker-Pshorr.................................... AHamms................................................ DHarp..................................................... UHarpoon.............................................. DHeineken............................................. SHenry Weinhard's.............................. DHigh Falls (All Brands)....................... DHoegaarden........................................ AHornsby's............................................ DHuson Valley...................................... DHumboldt........................................... DIce House (Miller).............................. DIsenbeck.............................................. AJohn Courage..................................... SKilkenny.............................................. UKillarney.............................................. DKillian's Red........................................ DKronenbourg 1664............................. ALabatt's (All Brands).......................... DLagunitas............................................ DLeffe.................................................... SLost Coast........................................... DMad River........................................... DMagners.............................................. UMcChouffe.......................................... AMcEwan's............................................ SMichael Shea's.................................... DMichelob (All Brands)........................ DMickey's.............................................. DMiddle Ages (All Brands).................. DMiller (All Brands).............................. DMilwaukee's Best............................... DModelo................................................ DMolson (All Brands)........................... DMoosehead......................................... DMurphy's Irish Stout.......................... SNatural Ice (Light).............................. DNew Amsterdam................................ DNew Castle Brown Ale....................... SNorth Coast........................................ DO'Doul's.............................................. DOld Milwaukee................................... DOld Speckled Hen.............................. GOld Vienna (OV)................................. DOskar's Blues...................................... DPabst (All Brands).............................. DPalm.................................................... A

Paulaner............................................. APete's Wicked Ale.............................. DPilsner Urquell................................... SPortland.............................................. DPyramid.............................................. DRed Dog.............................................. DRed Hook........................................... DRed Wolf............................................ DRhino Chasers.................................... DRogue................................................. DRohrbach's (All Brands).................... DRolling Rock....................................... DSam Adam's....................................... DSaranac............................................... DSchaeffer............................................ DSchlitz................................................. DScottish Newcastle Brown................ SShipyard............................................. DSierra Nevada.................................... DSir Perry William's............................. GSwithwick's Irish Ale......................... USouth Paw Light................................ DSpaten................................................. ASt. Pauli Girl....................................... SStella Artois........................................ SStrohs................................................. DStrongbow......................................... STecate................................................. DTennent's............................................ GThomas Creek.................................... DVictoria Bitter.................................... AWarsteiner.......................................... AWatney's............................................ GWeihenstephan.................................. AWeinhard's......................................... DWexford Irish Cream Ale.................. GWoodchuck Cider.............................. DWoodpecker...................................... SYuengling........................................... DZebra................................................... D

Keg Master ListNOTE: THIS LIST IS FOR REFERENCE ONLY

D=US SankeyS=Euro SankeyG=Euro Type G (BC-100)

A=Euro Type A (DS-100)U=Euro Type U (GC-100)


800-T740SN60

800-B800C-60

88

Index


AAdd-A-Faucet 19Air Shaft Components 59-60Air Distributor Bars 41Air Line 42

BBack Bar Coolers 73-74Bag-In-Box Connectors 77Ball-Lock Tank 76Barrel Heads 18Barrier Tubing 43Beer Check/Leak Detectors 53Beer Dispensers, Portable Units 69-70Beer Grease 31,62Beer Pumps 50Beer Line 42Beer Switch 51Blenders 52Blow Out Kit 54Blowers 59Bonnet Anglers 36Bottle Coolers 73-74Braided Tubing 42-43Brushes, Faucet 81Brushes, Glass 81

CCable Ties 86Cabinets, Beer 16Carbonator 77Ceramic Towers 12-13Chemicals, Line Cleaning 82-83Chemicals, Glass Washing 83Clamp on Towers 65Clamps 48Cleaner, Electric 80Cleaning Can 79Cleaning Kits 79CO2 Accessories 54CO2 Gas Detector 53CO2 Leak Detectors 53CO2 Tanks 54Coil Box Coolers & Parts 63Coils, Stainless Steel 63Cold Plate Coolers & Parts 64-65Cold Plates & Parts 64Coolers, Back Bar 73-74Coolers, Coil Box 63Coolers, Cold Plate 64-65Cooling Blocks, Aluminum 20Corny Keg 76Crimpers 48Couplers 28-31Coupler, Twin Probe Parts 31

DDirect Draw Dispensers 69-72Disconnects, Air Line 47Distributor Bars 41Draftec Line Cleaner 83Drain Bottle Kit 68Drain Fittings 27Drip Trays 22-27,68Dual Tap Shanks 32Ducts, Air Shaft 59

EElbows 44Electric Coil Cleaner 80

FFaucet Brushes 81Faucet Extensions 36Faucet Guards 36

Faucet, Plastic 62Faucet Locks 36Faucet Parts & Accessories 34-36Faucets 33-36Fittings, Beer Line 44-47Fittings, Compression 63Fittings, Hose 44-47Fittings, Stainless Steel 44-47Flex Duct- Air Cooled Systems 59Flow Control Faucets 33-34Flushers 78Foam on Beer Detectors (F.O.B.S) 51Fruit Fly Bar Pro Strips 86

GGas Blenders 52Gas Switchover Kit 53Gas Tank Holder 54Gauge Protectors 40Glass Brushes 81Glass Rinsers 25,27Glass Washers 81Glycol 58Glycol Components 58Glycol Feed line 55Glycol Units 56-57Growler Filler 36

HHand Trucks, Parts & Accessories 84-85Hex Nuts 46High Pressure Regulators 37-39Home Brewing Equipment 76Hose Cutters 43Hose Nipples, Brass/Stainless 46Hose Splices, Stainless 44Hydrometers 58

IIce Machine Cleaner 83In-Line Check Valve 52In-Line Shut Off 41,47Insulation 58-59Irish Coffin Box 17

JJockey Boxes 63-65John Guest Fittings 47

KKeg Bumpers 75Keg Jackets 65Keg Stackers 75Keg Tubs 65Keg Coupler Parts & Accessories 28-31Keg Couplers 28-31Keg Dolly 75Keg Shut-Offs 31Keg Pumps 60-62Keg Storage & Transport 75Knobs 36

LLeak Detectors 53Lock - Faucet 36Lube, Probe 31

MManifolds - Gas 41Manifolds – Beer 50Manifolds – Cleaning 78Mounting Brackets, Blower & Duct 59Mushroom Towers 14

NNitrogen Regulator 37-38Nipple, Hose 46Nipple Shanks 32

OO-Ring removal kit 62

PPanels 49Party Tubs 65Picnic Pumps, Parts & Accessories 60-62Pin-Lock Keg 76Polyethylene Tubing 42Portable Dispenser 69-70Power Packs 56-57

QQuick Disconnects 47

RRacks, Keg 75Refrigerator Conversion Kits 66-67Regulators 37,39Repair Kits, Regulators 87Repair Kits, Faucets 87Restrictor Kits 21Rinser Trays 25Rinser, Replacement 27Rotary Vane Pump 58Rubber Washers 46

SSecondary Regulators 39Shanks & Parts 32Shotgun Shanks 32Shut Off’s 41Soda Dispensing Equipment 77Spanner Wrench 86Splices Stainless steel 44Spout Plug 36Stout Faucet 33

TTanks, Gas & Mixed Gas 54Tape 58Temperature Controller 68Thermometers 86Tools 86Tower Add-A-Faucets 19Tower Bolt Set 21Tower Parts & Accessories 19-21Towers, Beer 2-18Trunk Lines 55Tubing 42-43

UUnderbar Cabinet 15-17

VVinyl Tubing 42

WWall Brackets 51Wall Mount Drip Tray 16Wall Panels 49Wine Equipment 77Wing Nuts 46Worm Drive Clamps 48Wrenches 86

ZZip Ties 86

Documents

D a B E & S · 2014-09-10 · Gallon Home Brew Keg Sixth Barrel Quarter Barrel Slim Quarter Barrel Half Barrel T