Cut Cones

Cut Cones

Department Department

of of

TechnologicTechnological al

EducationEducation

Gra

phic

G

raphic

C

om

munic

ati

on

Com

mu

nic

ati

on

Cut Cones

At the end of this unit you will be able to:

•Identify a Cone and draw orthographic views of Cones with cut surfaces.•Project a cut surface on a Cone between the Elevation, Plan and End Elevation.

•Construct a Surface Development of a Cone.

•Draw the True Shape of a cut surface on a Cone.

Cut cone

The given views show the Front Elevation and part Plan of a cut cone.

Draw the following views :-

Complete PlanEnd ElevationDevelopmentTrue Shape of cut

Department of Technological EducationDepartment of Technological Education

Finding position of End Elevation


Start drawing the End Elevation by projecting the height and width from the given views.

Drawing Generators on Plan


Use 30o and 60o lines to divide the Plan into 12 equal parts.

1

2

3

4

567

8

9

10

1211

Number each of the points on the Plan.

Transfer Generators from Plan to Elevation


Project each of the points from the Plan onto the Elevation base.

1 2345678

910 11 12

1

2

3

4

567

8

9

10

1211

Number each of the points on the Elevation making sure that the numbers correspond with those on the Plan.

Drawing generator on Elevation


Draw generators from the apex of the cone to each of the points found on the base of the cone.

1 2345678

910 11 12

Drawing generators onto End Elevation


1211

10

9

8

76 5

4

3

2

1

9108

117

126

15

243

Project the position of the generators onto the End Elevation by projecting the points from the Plan.

6584 3

102

111127 9

Number each of the points on the End Elevation.

Draw generators from the apex to the base.

Finding cut points on End Elevation


Project the points where the generators on the Elevation cross the cut onto the End Elevation.

1211

10

9

8

76 5

4

3

2

1

9108

117

126

15

243 65

84 3

102

111127 9

Mark each of the points found with a small dot.

Completing End Elevation


Complete the End Elevation by drawing a smooth curve through each of the point and then darkening the other outlines on the view.

9108

117

126

15

243 65

84 3

102

111127 9

Finding cut points on Plan

Project the points from the cut on the Elevation up to the correct generator lines on the Plan.

(Note that points 6 and 12 will not be able to be found at this time.)


9108

117

126

15

243 65

84 3

102

111127 9

Mark each of the points found with a small dot

Finding points 6 and 12 on Plan (alternative 1)

Project point 6 and 12 onto the outside generator on the Elevation.


Project this point up to the centre line of the Plan.

Use compasses to rotate this point onto the correct generators for points 6 and 12.

Mark each of these points with a small dot

Finding points 6 and 12 on Plan (alternative 2)

Project points 6 and 12 from the End Elevation onto the correct generators on the Plan.


Completing Plan

To complete the Plan draw a smooth curve through each of the 12 points found.


Development of surface (1)

Mark the position where the apex of the Development will be placed.


9 87

6

5

4

3

2

1

12

11

9

10Draw the first generator.

Draw the base line of the Development.

Step off the size to each generator point along the base.

Number each of the points found.

Draw generator lines from the apex to each of the points on the base.


Mark each of the found points with a small dot.


It is necessary to find the ‘true length’ of the cut points along each generator.

To find these sizes project a line through each point on the cut of the Elevation to the outside generator.


Measure the distance from the apex to each point on the outside generator.


Transfer this size to the correct generator on the Development.

Mark each point with a small dot.

Draw a smooth curve through each point found.

Darken each of the other outlines on the Development.

If the development of the outer surface was to be made from sheet metal thenit would have been developed starting with the shortest edges to the outside.The reason is that less work and materials would be required for the joins

True Shape of cut (1)

Project each of the points on the cut of the Elevation away at right angles to the cut surface.


Draw a datum line on the True Shape – in this case the centre line has been chosen.

Number each of the lines projected up to the True Shape.


Measure the sizes from the cut points to the centre line on the Plan and transfer each of these sizes to the correct lines on the True Shape.

Note – These sizes can also be measured from the End Elevation.

Mark each of the points with a small dot.



To finish the True Shape draw a smooth curve through each of the points found.


The final drawing should look like this.

Documents

Cut Cones