Curriculum Vitae

Reza Jamshidi Chenari, Ph.D in Geotechnics

Associate Professor (Tenured),

Faculty of Engineering,

University of Guilan

Faculty of Engineering, University of Guilan, 41996-13776 Guilan, Iran. Tel./Fax: (+98) 13-33690824 Mobile: (+98)-9111317195

mailto:jamshidi_reza@guilan.ac.ir

EDUCATION:

2008 Doctor of Philosophy (Ph.D) Civil Engineering, Geotechnical Engineering Iran University of Science and Technology, Tehran, Iran

2001 Master of Engineering (M.Eng.) Civil Engineering, Geotechnical Engineering Sharif University of Technology, Tehran, Iran

1999 Bachelor of Science (B.SC.) Civil Engineering, Structural Engineering Sharif University of Technology, Tehran, Iran

RESEARCH PUBLICATIONS:

Thesis

o Jamshidi Chenari, R. (December 2001): "The Optimization of the Construction Sequences of Large Underground Spaces Using the Instrumentation Results.", M.Eng. Thesis, Department of Civil Engrg., Sharif University of Technology, Tehran, Iran.

o Jamshidi Chenari, R. (March 2008): "Study of Dynamic Performance of Carpet Waste Strip Reinforced Retaining Walls in Shaking Table.", Ph.D. Thesis, Department of Civil Engrg., Iran University of Science and Technology, Tehran, Iran.

Journals

1. Ghiassian, H., Jamshidi Chenari, R. and Poorebrahim, G. (2006): "Neural Networks Analysis of Silty Sand Reinforced by Carpet Wastes.", Kuwait Journal of Science and Engineering, Vol. 33, No.1.

2. Ghiassian, H., Jamshidi Chenari, R., Shahnazari, H. and Tabarsa, A. (2008): “Dynamic Performance of Toyoura Sand Reinforced with Randomly Distributed Carpet Waste Strips using a Laminar Box on Shaking Table”, Journal of Seismology and Earthquake Engineering (Special Issue), Vol. 10, PP. 195-203.

3. Shahnazari, H, Ghiassian, H., Noorzad, A., Shafiee, A., Tabarsa, A. and Jamshidi Chenari, R. (2009): “Shear Modulus of Silty Sand Reinforced by Carpet Waste Strips.”, Journal of Seismology and Earthquake Engineering, Vol. 11, No. 3, PP. 133-142.

4. Ghiassian, H., Shahnazari, H., Tabarsa, A. and Jamshidi Chenari, R. (2010): “Damping Ratio of Silty Sand Reinforced with Carpet Fibers.”, Amirkabir Journal of Science and Technology, Vol. 42, No. 1, PP. 65-72.

5. Jamshidi Chenari, R., Towhata, I., Ghiassian, H. and Tabarsa, A., (2010): “Experimental evaluation of dynamic deformation characteristics of sheet pile retaining walls with fiber reinforcement backfill soil.”, Journal of Soil Dynamics and Earthquake Engineering, Vol. 30, PP. 438-446.

6. Jamshidi Chenari, R., Oloomi Dodaran, R. (2010): “New method for estimation of the scale of fluctuation of geotechnical properties in natural deposits.”, Journal of Computational Methods in Civil Engineering (CMCE), Vol. 1, No.1, PP. 55-64.

7. Molla Abasi, H. and Jamshidi Chenari, R. (2011): “Evaluation of liquefaction potential of Mazandaran province utilizing field and laboratory studies using Ishihara Criterion.”, Sharif Journal of Science and Research, Vol. 28, No.4, PP. 127-135.

8. Jamshidi Chenari, R. and Karimian, A. (2011): “Realisation of undrained shear strength of natural alluvial deposits using random field theory.”, Journal of Computational Methods in Engineering , Vol. 30, No.2, PP. 21-43.

9. Pishgah Gilani, P. and Jamshidi Chenari, R. (2011): “Discussion of “Probabilistic Analysis of Coupled Soil Consolidation” Jinsong Huang, D.V. Griffiths and Gordon A. Fenton”, Journal of geotechnical and geoenvironmental engineering (ASCE), Vol. 137, No. 9, PP. 857-858.

10. Jamshidi Chenari, R. and Oloomi Dodaran, R. (2011): “Evaluation of the heterogeneity in deformability of natural alluvial deposits using random field theory.”, Sharif Journal of Science and Research, Vol. 27, No.4, PP. 75-83.

11. Jamshidi Chenari, R. and Oloomi Dodaran, R. (2011): “Estimation of the Scale of Fluctuation of Geotechnical Properties in Natural Deposits Using Random Field Theory.”, Modares Journal of Science and Research, Vol. 11, No.4, PP. 17-27.

12. Ghiassian, H., Shahnazari, H., Noorzad, A., Tabarsa, A. R. and Jamshidi Chenari, R. (2012): “Nonlinear behavior of fine sand reinforced with carpet waste strips under undrained cyclic loading.”, Kuwait Journal of Science and Engineering, Vol. 39, PP. 15-36.

13. Jamshidi Chenari, R. and Alaie, R. (2012): “Effect of the Heterogeneity of Undrained Shear Strength on the Stability of Natural Slopes.”, Sharif Journal of Science and Research, Vol. 29, No.2, PP. 13-22..

14. Esfandiari, M. B. and Jamshidi Chenari, R. (2012): “Investigation on the effect of carpet fiber inclusion on hydraulic conductivity of clean sand using laboratory and random finite element analyses.”, International Journal of Civil engineering (IJCE), Vol. 12, No.1, PP. 72-79.

15. Jamshidi Chenari, R., Alinejad Taheri, A. and Davoodi, M.A. (2012): “Uncertainty in fundamental natural frequency estimation for alluvial deposits.”, Journal of Computational Methods in Civil Engineering,(CMCE), Vol. 3, No.1, PP. 77-94.

16. Eslami Kenarsari, A., Jamshidi Chenari, R. and Eslami, A. (2013): “Characterization of the correlation structure of residual CPT profiles in sand deposits.”, International Journal of Civil engineering (IJCE), Vol. 11, No.1, PP. 29-37.

17. Pishgah Gilani, P. and Jamshidi Chenari, R. (2014): “Reliability measures for consolidation settlement by means of CPT data.”, International Journal of Civil engineering (IJCE), Vol. 12, No. 2, PP. 213-218.

18. Jamshidi Chenari, R. and Mahigir, A. (2014): “The effect of spatial variability and anisotropy of soils on bearing capacity of shallow foundations.”, Civil Engineering Infrastructures journal (CEIJ), Vol. 47, No.2, PP. 199-214.

19. Jamshidi Chenari, R., Zhalehjoo, N. and Karimian, A. (2014): “Estimation on bearing capacity of shallow foundations in heterogeneous deposits using analytical and numerical methods.”, International Journal of Science and Technology (SCIENTIA IRANICA), Vol. 21, No.3, PP. 505-515.

20. Ranjbar Pouya, K., Zhalehjoo, N. and Jamshidi Chenari, R. (2014): “Influence of Random Heterogeneity of Cross Correlated Strength Parameters on Bearing Capacity of Shallow Foundations.”, Indian Geotechnical Journal, Vol. 44, No.2, PP. 427-435.

21. Tizpa, P., Jamshidi Chenari, R., Karimpour Fard, M. and Machado, S.L. (2014): “ANN prediction of some geotechnical properties of soil from index parameters.”, Arabian Journal of Geosciences (Springer), Vol. 8, No.4, PP. 2911-2920.

22. Jamshidi Chenari, R., Tizpa, P., Ghorbani Rad, M.R., Machado, S.L. and Karimpour Fard, M. (2014): “The use of index parameters to predict soil geotechnical properties.”, Arabian Journal of Geosciences (Springer), 1-13.

23. Arabani, M., Jamshidi Chenari, R. and Sadeghnejad Limoui, M. (2014): “Using of 2D finite element modeling to predict the glasphalt mixture rutting behavior.”, Journal of Construction and Building Materials (Elsevier), Vol. 68, PP. 183-191.

24. Jamshidi Chenari, R. and Sadeghnejad Limoui, M. (2014): “Numerical study of the effect of glass powder on behavior of glasphalt mixture”, Journal of Engineering of Transportation Infrastructure, Vol.1, No. 2.

25. Karimpour Fard, M., Jamshidi Chenari, R. and Soheili, F. (2015): “Shear strength characteristics of sand mixed with EPS beads using large direct shear apparatus.”, Electronic Journal of Geotechnical Engineering (EJGE), Vol. 20, PP. 2205-2220.

26. Jamshidi Chenari, R., Yousefi Barandagh, A. and Esfandiari, M. B. (2015): “Evaluation of the effect of Carpet Fibers inclusion on pore pressure development behavior of Anzali sand in quick tank.”, Sharif Journal of Science and Research, Vol. 31.2, No.1.2, PP. 133-40.

27. Jamshidi Chenari, R., Kamyab Farahbakhsh, H. and Zamanzadeh, M. (2015): “Investigation into the Effect of the Inherent Heterogeneity of Soil on the Long Term Stability of Earth Slopes.”, Sharif Journal of Science and Research, Vol. 31.2, No.3.1, PP. 3-17.

28. Jamshidi Chenari, R., Rabanifar, H. and S. Veiseh (2015): “Utilization of Sepidrud Dam Basin Sediments in Fired Clay Bricks.”, Journal of Materiales de Construcción (CSIC), Vol. 65, No. 320 ( http://dx.doi.org/10.3989/mc.2015.07014).

29. Jamshidi Chenari, R. and Kamyab Farahbakhsh, H. (2015): “Generating non-stationary random fields of auto-correlated, normally distributed CPT profile by matrix decomposition method”, Journal of Georisk-assessment and management of risk for Engineered Systems and Geohazards, Vol. 9, No. 2, PP. 96-108.

30. Jamshidi Chenari, R. and Alaie, A. (2015): “Effects of Anisotropy in Correlation Structure on the Stability of an Undrained Clay Slope”, Journal of Georisk-assessment and management of risk for Engineered Systems and Geohazards, Vol. 9, No. 2, PP. 109-123.

31. Jamshidi Chenari, R., Karimpour Fard, M., Pourghaffar Maghfarati, S., Pishgar, F. and Machado, S.L. (2016): “An investigation on the geotechnical properties of sand-EPS mixture using large oedometer apparatus.”, Journal of Construction and Building Materials, Vol. 113, PP. 773–782.

32. Jamshidi Chenari, R., and Aminzadeh Bostani Taleshani, S. (2016): "Site response of heterogeneous natural deposits to harmonic excitation applied to more than 100 case histories." Earthquake Engineering and Engineering Vibration (Springer), Vol. 15, No. 2 PP. 341-356.

33. Eslami, A., Heidarie Golafzani, S. and Jamshidi Chenari, R. (2016): "Assessment of Babolsar Concrete Pedestrian Bridge Failure for 1964 Flood Event and Retrofitting Practice." Engineering Failure Analysis (Elsevier), Vol. 68, PP. 101-112.

34. Jamshidi Chenari, R. and Zamanzadeh, M. (2016): “Uncertainty Assessment of Critical Excavation Depth of Vertical Unsupported Cuts in Undrained Clay Using Random Field Theorem”, International Journal of Science and Technology (Scientia Iranica), Vol. 23, No. 3, PP. 864-875.

35. Jamshidi Chenari, R., Azadegan, A. (2016): “Dynamic Elasto-Plastic Finite Element Analysis of Buried Pipelines in Slopes”, Electronic Journal of Geotchnical Engineering (EJGE), Vol. 21, No. 13, PP. 4797-4811.

36. Jamshidi Chenari, R. and Seyed Noori, N. (2016).: “Uncoupled Consolidation of Deterministic Heterogeneous Clay Deposits.”, Iranian Journal of Science and Technology (IJST), 41 (1): 49-53. DOI: 10.1007/s40996-016-0038-8.

37. Jamshidi Chenari, R., Fatahi, B., Akhavan Maroufi, M.A. and Alaie, R. (2017): “Experimental and Numerical Investigation on Compressibility and Settlement Behavior of Sand Mixed with TDA.”, Journal of Geotechnical and Geological Engineering (Springer), 35 (5): 2401-2420. DOI: 10.1007/s10706-017-0255-3.

38. Jamshidi Chenari, R., Karimpour Fard, M., Shafie, J. and Ghorbanpour, A. (2017): “Tire Shreds and Tire Crumbs Inclusion: Contrast Effects on Bearing Capacity of Sand.”, Electronic Journal of Geotechnical Engineering (EJGE), 2017 (22.09), pp 3649-3667.

39. Jamshidi Chenari, R., Poursalimi, N., and Shamsi Sosahab, J. (2017): ”Dynamic properties of sand- tire crumb mixtures with large cyclic direct shear apparatus.”, Electronic Journal of Geotechnical Engineering (EJGE), 2017 (22.13), pp 5085-5104.

40. Veiskarami, M., Jamshidi Chenari, R. and Jame’ei, A.A. (2017):”Bearing Capacity of Strip Footings on Anisotropic Soils by the Finite Elements and Linear Programming.”, International Journal of Geomechanics (ASCE), 2017 (17.12). Doi.org/10.1061/(ASCE)GM.1943-5622.0001018.

41. Mohafezatkar Sareshkeh, A., and Jamshidi Chenari, R. (2017): “Induced Settlement Reduction of Adjacent Masonry Building in Residential Constructions.”, Civil Engineering Journal, 3(7), 450-462.

42. Jamshidi Chenari, R., Firoozfar, A., Attari, S., Izadi, A. and Shafie, S. E. (2017): “Deformation Characteristics of Sand Geofoam Blocks using Large-Scale Oedometer Apparatus.”, Civil Engineering Journal, 3(8), 585-593.

43. Jamshidi Chenari, R., Behfar, B. (2017): “Stochastic Analysis of Seepage through Natural Alluvial Deposits Considering Mechanical Anisotropy”, Civil Engineering Infrastructures Journal, 50(2): 233–253, December 2017, https://doi.org/ 10.7508/ceij.2017.02.003.

44. Jamshidi Chenari, R. and Mahigir, A. (2017): “The Effect of Mechanical Anisotropy and Heterogeneity of Shear Strength Parameters of Soils on Drained Bearing Capacity of Shallow Foundations.”, Journal of Computational Methods in Engineering, 36(1), 149-159, doi:10.18869/acadpub.jcme.36.1.149.

45. Jamshidi Chenari, R., Karimpour Fard, M., Navari, S. and Shamsi Sosahab, J. (2017): “Land Reclamation Project in Anzali Harbor using Dynamic Compaction.” Computational Research Progress In Applied Science & Engineering (CRPASE), 03(04): 153-164, December 2017.

46. Shahnazari, H, Jamshidi Chenari, R., Karimpour Fard, M., and Heshmati, S. (2017): ”Stability Evaluation of Un-braced Cuts.”, International Journal of Civil Engineering (Springer), December 2017, https://doi.org/10.1007/s40999-017-0273-9.

47. Alaie, R., and Jamshidi Chenari, R. (2018): “Cyclic and Post-Cyclic Shear Behaviour of Interface between Geogrid and EPS Beads-Sand Backfill.”, KSCE Journal of Civil Engineering (Springer), 22(9), 3340-3357, https://doi.org/10.1007/s12205-018-0945-2.

48. Jamshidi Chenari, R., Soltankhah Pishkhani, S., Karimpour Fard, M., and Shamsi Sosahab, J. (2018): ”Experimental and Numerical investigation of Dynamic Properties of Soil Stabilized by Young Vetiver.”, Rivista Italiana di Geotecnica, 43-53, January-March 2018, https://doi.org/10.19199/2017.4.0557-1405.47.

49. Jamshidi Chenari, R., Izadi, A. and Nazemi Sabet Soumehsaraei, M. (2018): “Discussion of “Seismic Bearing Capacity of Shallow Strip Footing with Coulomb Failure Mechanism using Limit Equilibrium Method” Sima Ghosh and Litan Debnath”, Journal of geotechnical and geological (Springer), 36(6), 4037-4040, February 2018 https://doi.org/10.1007/s10706-018-0497-8.

50. Jamshidi Chenari, R., Kamyab Farahbakhsh, H., Heidarie Golfazani, S. and Eslami A. (2018):"Non-Stationary Realization of CPT Data Considering Lithological and Inherent Heterogeneity." Journal of Georisk-assessment and management of risk for Engineered Systems and Geohazards, 12(4): 265-278, https://doi.org/10.1080/17499518.2018.1447675.

51. Jamshidi Chenari, R., Fatahi, B., Ghorbani, A. and Nasiri Alamooti, M. (2018): “Evaluation of Strength Properties of Cement Stabilized Sand Mixed with EPS Beads and Fly Ash.”, Geomechanics and Engineering, An International Journal (Techno Press), Vol. 14, No. 6, 533-544. DOI: https://doi.org/10.12989/gae.2018.14.6.000.

52. Jamshidi Chenari, R., Ghorbani, A., Eslami, A. and Mirabbasi, F. (2018): “Behavior of Piled Raft Foundation on Heterogeneous Clay Deposits Using Random Field Theory.”, Civil Engineering Infrastructures Journal (CEIJ), 51(1): 35–54, June 2018, DOI: 10.7508/ceij.2018.01.003.

53. Alaie, R., and Jamshidi Chenari, R. (2018): “Design and Performance of a Single Axis Shake Table and a Laminar Soil Container.”, Civil Engineering Journal, Vol. 4, No. 6, June, 2018, http://dx.doi.org/10.28991/cej-0309176.

54. Mohseni, S., Payan, M., and Jamshidi Chenari, R. (2018) : “Soil-Structure Interaction Analysis in Natural Heterogeneous Deposits Using Random Field Theory.”, Journal of Innovative Infrastructure Solutions (Springer), 3(1): 62, December, 2018, https://doi.org/10.1007/s41062-018-0168-x.

55. Shamsi Sosahab, J., Jamshidi Chenari, M., Jamshidi Chenari, R., and Karimpour Fard, M. (2018): “Physical and Numerical Modeling of Piled Raft Foundation in Chamkhaleh Sand.”, International Journal of Civil Engineering (Springer), 17(6), 765-779 DOI: 10.1007/s40999-018-0365-1.

56. Sasanian, S., Soroush, A., and Jamshidi Chenari, R. (2018): “Impact of the sampling intervals on the scale of fluctuation of random fields.”, International Journal of Civil Engineering (INCE) DOI: 10.1007/s40999-018-0371-3.

57. Veiskarami, M., Jamshidi Chenari, R. and Jame’ei, A.A. (2018): ” A Study on the Static and Seismic Earth Pressure Problems in Anisotropic Granular Media.”, Journal of Geotechnical and Geological Engineering (Springer) DOI: 10.1007/s10706-018-0739-9.

58. Gohari Lasaki, A., Jamshidi Chenari, R., Shamsi Sosahab, J., and Jafarian, Y. (2018): “Investigation of Strength Parameters of PVA Fiber-Reinforced Fly Ash-Soil Mixtures in Large-Scale Direct Shear Apparatus.”, Civil Engineering Journal, Vol. 4, No. 11, November, 2018, DOI: 10.28991/cej-03091186.

59. Jamshidi Chenari, R., Taleb, A., Ghoreishi, M., and Payan, M. (2018): “Physical Modelling of Cohesive Soil Inherent Variability: Consolidation Problem.”, International Journal of Geo-Engineering (Springer) 9: 25. DOI: 10.1186/s40703-018-0094-y.

60. Jamshidi Chenari, R., Alaie, R. and Fatahi, B. (2018): “Constraint Compression Models for Tire-Derived Aggregate-Sand Mixtures Using Enhanced Large Scale Oedometer Testing Apparatus.”, Journal of Geotechnical and Geological Engineering (Springer) https://doi.org/10.1007/s10706-018-00780-2.

61. Izadi, A., Nazemi Sabet Soumehsaraei, M., Jamshidi Chenari, R., and Ghorbani, A. (2018): “Pseudo-Static Bearing Capacity of Shallow Foundations on Heterogeneous Marine Deposits using Limit Equilibrium Method.”, Marine Georesources and Geotechnology (Taylor & Franics) DOI:10.1080/1064119X.2018.1539535.

62. Rezaie Soufi, G., Jamshidi Chenari, R. and Karimpour Fard, M. (2019): “Influence of Random Heterogeneity of the Friction Angle on Bearing Capacity Factor Nγ.” Journal of Georisk-assessment and management of risk for Engineered Systems and Geohazards https://doi.org/10.1080/17499518.2019.1566554.

63. Jamshidi Chenari, R., Kamyab Farahbakhsh, H. and Izadi, A. (2019): ”Continuous Slip Surface Method for Stability Analysis of Heterogeneous Vertical Trenches.”, International Journal of Science and Technology (Scientia Iranica) https://doi.org/ 10.24200/SCI.2019.21227.

64. Jamshidi Chenari, R., Fatahi, B., Ghoreishi, M., and Taleb, A. (2019): “Physical and Numerical Modeling of Inherent Variability of Shear Strength in Soil Mechanics.”, Geomechanics and Engineering, An International Journal (Techno Press), Vol. 17, No. 1 (2019) 31-45, https://doi.org/10.12989/gae.2019.17.1.031.

65. Jamshidi Chenari, R., and Izadi, A. (2019): “Discussion of “An Analytical Probabilistic Analysis of Slopes based on Limit Equilibrium Methods”, Bulletin of Engineering Geology and the Environment (Springer), by A. Johari, S. Mousavi. November 2018, https://doi.org/10.1007/s10064-018-1408-1”, DOI: 10.1007/s10064-019-01473-7.

66. Jamshidi Chenari, R., and Aminzadeh Bostani Taleshani, S. (2019): "Numerical Evaluation of the Amplification Characteristic of Randomly Heterogeneous Natural Deposits." Indian Geotechnical Journal DOI: 10.1007/s40098-019-00350-0.

67. Jamshidi Chenari, R., Karimpour Fard, M., Jamshidi Chenari, M. and Shamsi Sosahab, J. (2019): “Physical and Numerical Modeling of Stone Column Behavior in Loose Sand.”, International Journal of Civil Engineering (INCE). 17(2), 231-244. DOI: 10.1007/s40999-017-0223-6.

68. Pakdel, P., Jamshidi Chenari, R., and Veiskarami, M. (2019): ”An Estimate of the Bearing Capacity of Shallow Foundations on Anisotropic Soil by Limit Equilibrium and Soft Computing Technique.”, Geomechanics and Geoengineering, An International Journal (Taylor & Francis), 14(3), 202-217, DOI: 10.1080/17486025.2019.1581276.

69. Jamshidi Chenari, R., Pourzeynali, S., and Alizadeh, B. (2019): “Seismicity Study of Bandar-e-Anzali Area by Zoning Peak Ground Acceleration and Response Spectra.“, Saudi Journal of Civil Engineering, 3(1), 1-16. DOI:10.21276/sjce.2019.3.1.1.

70. Jamshidi Chenari, R., Ebrahimi Khonachah, R., Hosseinpour Babaie, I., and Khajeh, A. (2019): “An experimental study for the cyclic interface properties of the EPS-sand mixtures reinforced with Geogrid.” International Journal of Civil Engineering (INCE) DOI: 10.1007/s40999-019-00424-3.

71. Sasanian, S., Soroush, A., and Jamshidi Chenari, R. (2019): “Two-Dimensional Random Field Conditioned by CPT Data: Case Study.”, International Journal of Civil Engineering (Springer) DOI: 10.1007/s40999-019-00419-0.

72. Hemmati Masouleh, F., Jamshidi Chenari, R., Saleh Jalali, R. and Ghorbani, A. (2019): "Site Response Analysis in Cross Anisotropic Alluvial Deposits Subjected to Inclined SH Waves.”, Innovative Infrastructure Solutions (Springer), 4: 32. DOI: 10.1007/s41062-019-0219-y.

73. Jamshidi Chenari, R., and Nasiri, A. (2019): “Site Response Analysis of Geotextile Fiber-Reinforced Toyoura Sand.”, International Journal of Geosynthetics and Ground Engineering (Springer), 5: 14, DOI: 10.1007/s40891-019-0166-x.

74. Jamshidi Chenari, R., Pourvahedi Roushandeh, S., and Payan, M. (2019): “Stochastic Analysis of Foundation Immediate Settlement on Heterogeneous Spatially Random Soil considering Mechanical Anisotropy.”, SN Applied Sciences (Springer), 1: 660, DOI: 10.1007/s42452-019-0684-0.

75. Tizpa, P., Jamshidi Chenari, R., and Farrokhi, F. (2019): “A Note on the Compressibility and Earth Pressure Properties of EPS Beads-Rigid Particulates Composite.”, Journal of Geotechnical and Geological Engineering (Springer) DOI: 10.1007/s10706-019-00977-z.

76. Heidarie Golafzani, S., Jamshidi Chenari, R., and Eslami, A. (2019): "Reliability Based Assessment of Pile Bearing Capacity: Static analysis, SPT and CPT-based Methods." Journal of Georisk-assessment and management of risk for Engineered Systems and Geohazards (Taylor & Francis) https://doi.org/10.1080/17499518.2019.1628281.

77. Alaie, R., Jamshidi Chenari, R. (2019): “Dynamic properties of EPS beads-sand mixtures using large-scale cyclic triaxial and bender element tests.”, Geosynthetics International (ICE) DOI: 10.1680/jgein.19.00034.

78. Payan, M., and Jamshidi Chenari, R. (2019): “Small Strain Dynamic Shear Modulus of Anisotropically Loaded Sands.”, Soil Dynamics and Earthquake Engineering (Elsevier) https://doi.org/ 10.1016/j.soildyn.2019.105726.

79. Payan, M., Khoshini, M., and Jamshidi Chenari, R.: “Elastic Dynamic Young's Modulus and Poisson’s Ratio of Sand-Silt Mixtures.”, Journal of Materials in Civil Engineering (ASCE) (Accepted for Publication).

80. Veiskarami, M., Jamshidi Chenari, R. and Jame’ei, A.A.: ”Closure to Bearing Capacity of Strip Footings on Anisotropic Soils by the Finite Elements and Linear Programming.”, International Journal of Geomechanics (ASCE), 2017 (17.12) (Accepted for Publication).

81. Pakdel, P., Jamshidi Chenari, R., and Veiskarami, M.: ”Seismic Bearing Capacity of Shallow Foundations Rested on Anisotropic Deposits.”, International Journal of Geotechnical Engineering (Taylor & Francis) ) (Accepted for Publication).

82. Shahmalekpoor, P., Jamshidi Chenari, R. and Javankhoshdel, S.: “Discussion of “Probabilistic Seismic Slope Stability Analysis and Design”, Candaian Geotechnical Journal (NRC), by Burgess, J., Fenton, G.A. and Griffiths, D.V., January 2019” (Accepted for Publication).

83. Sasanian, S., Soroush, A., and Jamshidi Chenari, R.: “Slope Stability Reliability Analysis due to Different Geotechnical Uncertainty Sources: GRF Algorithm.”, Proceedings of the Institution of Civil Engineers-Geotechnical Engineering (ICE) (Accepted for Publication).

84. Hakimi Basti, T., Jamshidi Chenari, R., and Firoozfar, A.: “Linear Visco-Elastic 1D Site Response Analysis of Sand-EPS Geofoam Composition under Cyclic Loading.”, Geosynthetics International (ICE) (Accepted for Publication).

85. Alaie, R., Jamshidi Chenari, R., and Karimpour Fard, M.: “Shaking Table Study on EPS beads-sand mixtures using Laminar Box Modelling.”, Geosynthetics International (ICE) (Accepted for Publication).

86. Heidarie Golafzani, S., Jamshidi Chenari, R. and Eslami, A.: “LRFD Calibration of Resistance Factors for Driven Piles Based on CPT Methods.”, Journal of Geotechnical and Geological Engineering (Springer) (Accepted for Publication).

87. Izadi, A., Nazemi Sabet Soumehsaraei, M., Jamshidi Chenari, R., Moallemi, S., and Javankhoshdel, S.: “Spectral Bearing Capacity of Shallow Strip Footing Under Pseudo-Dynamic Excitations.”, Geomechanics and Geoengineering (Taylor & Francis) (Accepted for Publication).

88. Madadzadeh M., Jamshidi Chenari, R., Lashteh Neshaei M. A., and Forghani, A.: “Changes in Stability Conditions of Clay Slopes due to Salt Leaching: an Example from Rasht, Iran.”, International Journal of Civil Engineering (Springer) (Accepted for Publication).

89. Foroutan Kalourazi, A., Izadi, A., and Jamshidi Chenari, R.: “Seismic Bearing Capacity of Shallow Foundations in the Vicinity of Slopes using the Lower Bound Finite Element Method.” Soils and Foundations (Elsevier) (Under Review).

90. Izadi, A., Foroutan Kalourazi, A., and Jamshidi Chenari, R.: “Effect of Roughness on Pseudo-Static Bearing Capacity of Shallow Foundations near Slopes using the Lower Bound Finite Element Method.” Soils and Foundations (Elsevier) (Under review).

91. Fathi, H., Jamshidi Chenari, R., and Vafaeian, M.: “Investigation of the Effect of Adding PET on Sand Monotonic and Cyclic Behavior.”, Geomechanics and Engineering, An International Journal (Techno Press) (Under Review).

92. Jamshidi Chenari, R., Elahi, A., Khajeh, A.: “Effect of the spatial variability of natural alluvial deposits constitutive parameters on bearing ratio of cap and pile in piled raft foundations.”, Geotechnics and Strength of Materials (Under review).

93. Javankhoshdel, S., Cami, B., and Jamshidi Chenari, R.: “Probabilistic Analysis of Slopes with Linearly Increasing Undrained Shear Strength Using RLEM Approach.”, Canadian Geotechnical Journal (NRC) (Under review).

94. Mafi, R., Javankhoshdel, S., Cami, B., Jamshidi Chenari, R. and Gandomi, A.: “Surface Altering Optimization in Non-circular Slope Stability Analysis Using RLEM.”, Canadian Geotechnical Journal (NRC) (Under review).

95. Rezaie Soufi, G., Jamshidi Chenari, R., and Javankhoshdel, S.: “Pseudo-Static vs. Pseudo-Dynamic Seismic Analyses in Bearing Capacity Problem.”, Soils and Foundations (Elsevier) (Under review).

96. Hakimi Basti, T., Jamshidi Chenari, R., Payan, M., and Senetakis, K.: “Experimental Investigation of Cyclic and Monotonic Shear Strength Behaviors of Sand–EPS Geofoam Interface.”, Geosynthetics International (ICE) (Under review).

97. Rezaie, B., Jamshidi Chenari, R., and Veiskarami, M.: “A Study on the Effect of Cement on Behavior of the Expanded Polystyrene Composite Soils.”, Journal of Geotechnical and Geological Engineering (Springer) (Under review).

98. Khajeh, A., Jamshidi Chenari, R. , and Payan, M.: ”A Simple Review of Cemented Non-Conventional Materials-Soil Composites.”, Journal of Geotechnical and Geological Engineering (Springer) (Under review).

99. Rezaie Soufi, G., Jamshidi Chenari, R., and Javankhoshdel, S.: “Conventional vs. Modified Pseudo-Dynamic Seismic Analyses in Bearing Capacity Problem.”, International Journal of Geomechanics (ASCE) (Under review).

100. Jamshidi Chenari, R., Alaie, R. and Karimpour Fard, M.: “Mechanical and Hydraulic Characteristics of Sand-Tire Crumbs Mixture Using Large Oedometer Apparatus.”, Construction Materials (ICE) (Under review).

101. Izadi, A., Jamshidi Chenari, R., Hemmati Masouleh, F., and Javankhoshdel, S.: “Effect of Love Wave Propagation on the Pseudo-Dynamic Bearing Capacity of Shallow Foundations using 3D Coulomb Failure Mechanism.”, Natural Hazards (Springer) (Under review).

102. Jamshidi Chenari, R., Izadi, A., Eslami, A. and Khaksar Najafi, E.: ” Approximation of Undrained Bearing Capacity of Strip Foundations on Heterogeneous Marine Clay.”, SN Applied Sciences (Springer) (Under review).

103. Tizpa, P., Jamshidi Chenari, R., Farrokhi, F., and Thoeni, K.: “Constraint Compression Behavior of Sand-EPS Beads Mixture using Discrete Element Modelling (DEM).”, Journal of Granular Matter (Springer) (Under review).

104. Pourzeynali, S., Jamshidi Chenari, R. and Alizadeh, B.: “Poisson distribution of Earthquakes in Iran with the Introduction of New Correlation Relations between the Magnitude Scales. “, Civil Engineering Research Journal (Under review).

105. Veiskarami, M., Jamshidi Chenari, R., Ahmadi Rahimabadi, M.A. and Hatefi, M.H.: “A Study on the Seismic Passive Earth Pressure on Rigid Retaining Walls Considering Seismic Acceleration Field.”, Soils and Foundations (Elsevier) (Under review).

106. Safardoost Siahmazgi, A.H., Jamshidi Chenari, R. and Veiskarami, M.:”Pseudo-Dynamic Bearing Capacity of Shallow Footing using Finite Element Lower Bound Limit Analysis Method.”, Bulletin of Earthquake Engineering (Springer) (Under review).

107. Maghsoudi, M.S., Jamshidi Chenari, R., and Farrokhi, F.: “A Comprehensive Analysis of Liquefaction-Induced Slope Ground Deformations in Shaking Table Test.”, Landslides (Springer) (Under review).

108. Foroutan Kalourazi, A., Jamshidi Chenari, R. and Veiskarami, M.:”Bearing Capacity of Strip Footings Adjacent to Anisotropic Slopes using the Lower Bound Finite Element Method.”, Acta Geotechnica (Springer) (Under review).

109. Veiskarami, M., Hosseinzadeh, H. R. and Jamshidi Chenari, R.: ”Characteristics and Experiments on Anisotropic Shear Strength of Chamkhaleh Sand.”, Advances in Civil Engineering Materials (ASTM) (Under review).

110. Tizpa, P., Kazempour, S., Jamshidi Chenari, R., Farrokhi, F., and Ahamdi, H.: “Numerical and Experimental Investigation of the Influence of Grain Size on the Compressibility of Sand-EPS Mixtures.”, Granular Matter (Springer) (Under review).

111. Fathi, H., Jamshidi Chenari, R., and Vafaeian, M.: “Shaking Table Study on PET Strips-Sand Mixtures using Laminar Box Modelling.”, Journal of Geotechnical and Geological Engineering (Springer) (Under review).

112. Shahpouri, H., Jamshidi Chenari, R., and Karimpour Fard, M.: “Evaluation of Bandar-e-Anzali Sand Strength in Large-Scale Cyclic Simple Shear Device.”, Asian Journal of Civil Engineering (Springer) (Under review).

113. Jamali, N., Jamshidi Chenari, R., and Veiskarami, M.: ”An Investigation on the Settlement of Shallow Foundations Resting on Cross-Anisotropic Soil Deposits.”, Iranian Journal of Science and Technology (IJST) (Springer) (Under review).

114. Khajeh, A., Jamshidi Chenari, R., Payan, M., and Pishgar, F.,: ”A Review of the Studies on Soil-EPS Composites: Beads and Blocks”, Geosynthetics International (ICE) (Under review).

115. Soroush, A., Sasanian, S., Jamshidi Chenari, R., and Shafipour Nourafshani, R.,: "Influence of Geotechnical Site Investigation in Horizontal Plane on Slope Reliability.”, Bulletin of Engineering Geology and the Environment (Springer) (Under review).

116. Ghollasi Mood, A., Jamshidi Chenari, R., Veiskarami, M. and Ahmadi, H.: " A Numerical Study on the Dynamic Interaction between a Machine Foundation and an adjacent Footing." Earthquake Engineering and Engineering Vibration (Springer) (Under review).

117. Fathipour, H., Jamshidi Chenari, R., and Veiskarami, M.: “Pseudo-Dynamc Earth Pressure in Active and Passive Loading Conditions.”, Geotechnique Letters (ICE) (To be submitted soon).

118. Haghsheno, H., Jamshidi Chenari, R. and Javankhoshdel, S.: “Seismic Bearing Capacity of Shallow Strip Footings on Sand Deposits with Weak Inter-layer.”, Journal of Central South University (To be submitted soon).

119. Nouzari, M. A., Pishgar, F. and Jamshidi Chenari, R.: “Seismic Bearing Capacity of Footings in Unsaturated Soils Employing Limit Equilibrium Method.” International Journal for Numerical and Analytical Methods in Geomechanics (ICE) (To be submitted soon).

120. Dastpak, P., Javankhoshdel, S., and Jamshidi Chenari, R.: “Non-circular Deterministic and Stochastic Slope Stability Analyses and Design of Simple Geosynthetic Reinforced Soil Slopes.”, Geosynthetics International (ICE) (To be submitted soon).

121. Khaksar Najafi, E., Arabani, M., and Jamshidi Chenari, R.: “The Potential Use of Fly Ash-Based Geopolymer as a Reactive Liner Material- A Review.” International Journal of Environmental Science and Technology (Springer) (To be submitted soon).

122. Sasanian, S., Soroush, A., and Jamshidi Chenari, R.: “Generation of Random Field due to Geotechnical Uncertainty Sources for Reliability Analyses: A Holistic Approach

(GRF).”, Bulletin of Engineering Geology and the Environment (Springer) (To be submitted soon).

123. Kazempour, S., Jamshidi Chenari, R., Ahmadi, H., and Payan, M.: ”Effect of Particle Size and Angularity on Mechanical Behavior of Sand-EPS Mixture”, Journal of Materials in Civil Engineering (ASCE) (To be submitted soon).

124. Rezaie Soufi, G., Jamshidi Chenari, R., Shalchiyan, M. and Karimpour Fard, M.: “Seismic Bearing Capacity of Reinforced Strip Foundations using Upper Bound Limit Analysis.”, Soils and Foundations (Elsevier) (To be submitted soon).

125. Khazaie, A., Jamshidi Chenari, R., and Rezaie Soufi, G.: “Seismic Bearing Capacity of two Interefering Strip Footings Using Finite Element Limit Analysis.” Journal of Geotechnical and Geological Engineering (Springer) (To be prepared).

126. Heidarie Golafzani, S., Jamshidi Chenari, R. and Eslami, A.: "Reliability Based Assessment of Pile Bearing Capacity: Static analysis, SPT and CPT-based Methods." Canadian Geotechnical Journal (NRC) (To be prepared).

127. Tizpa, P., Rezaie Soufi, G., Jamshidi Chenari, R., and Karimpour Fard, M.: ”A Review of the Studies on Distinct Element Modelling of Soil mixed with Non-conventional Materials”, Granular Matter (Springer) (To be prepared).

128. Payan, M., and Jamshidi Chenari, R.: “Small Strain Young’s Modulus and Poisson’s Ratio of Anisotropically Loaded Sands.”, Archives of Civil and Mechanical Engineering (Elsevier) (To be prepared).

129. Shahmalekpoor, P., Jamshidi Chenari, R. and Javankhoshdel, S.: “Stochastic Seismic Slope Stability Analysis using Non-Circular Random Limit Equilibrium Method (RLEM)”, Candaian Geotechnical Journal (NRC) (To be prepared).

Conferences

1. Sadaghiani, M.H., and Jamshidi Chenari, R., (January 2002): "The Effect of Construction Sequences in the Stability of Large Underground Spaces.", to appear in the proceedings of 1st Iranian Rock Mechanics Conference: Tarbiat Modares University, Tehran, Iran (29-30 January 2002) (in Persian).

2. Tabanrad, R., Sharif Vaghee, S.A., and Jamshidi Chenari, R. (January 2002): "Convergence Estimation of Power Tunnels of Karun 3 H.E.P.P.", Proc. 1th Iranian Rock Mechanics Conference: Tarbiat Modares University, Tehran, Iran (29-30 January 2002) (in Persian).

3. Jamshidi Chenari, R., (August. 2004): "The Optimization of the Construction sequences of Large Underground Spaces using the Instrumentation Results.”, 32th International Geological Congress, Florence, Italy.

4. Nikkhah, M., and Jamshidi Chenari, R. (May 2006): "Field Calibration of Total Pressure Cells in Earth Dams.”, 7th International Congress on Civil Engineering, Tarbiat Modarres University, Tehran, Iran (in Persian).

5. Jamshidi Chenari, R., and Nikkhah, M. (June 2006): "A New Device for Field Calibration of Total Pressure Cells in Doosti and Esfarayen Dams.”, Proceedings of the International Symposium on Dams in the Societies of the 21st Century, ICOLD-SPANCOLD - Dams and Reservoirs, Societies and Environment in the 21st Century, pp.521, Barcelona, Spain.

6. Jamshidi Chenari, R. (October, 2006): "Sensitivity Analysis of Magnetic Extensometers for Measuring Vertical Movement in Foundation of earth Dams.”, 4th International Conference on Soft Soil Engineering, Vancouver, British Columbia, Canada.

7. Shahbazian, H., Fakharian, K., and Jamshidi Chenari, R. (2007): “Numerical investigation of trench geometry and soil property effects on the accuracy of embedded pressure cell measurements.”, 60th Canadian Geotechnical Conference, October 21-24, Ottawa, Canada, Vol. 2, pp. 1199-1206.

8. Ghiassian, H., Jamshidi Chenari, R., and, Tabarsa, A. (2008): “Dynamic Performance of Toyoura Sand Reinforced with Randomly Distributed Carpet Waste Strips.”, 4th decennial Geotechnical Earthquake Engineering and Soil Dynamics Conference: Sacramento, California, USA (18-22 May, 2008).

9. Jamshidi Chenari, R., and, Ahmadi, H. (2010): “Adjacent building induced settlement reduction in residential constructions.”, 3rd National Congress on Urban Management and Construction Stability: Azad University of Khomein, Arak, Iran (20 May, 2010).

10. Rabanifar, H., Jamshidi Chenari, R., and, Forghani, A. (2010): “Shrinkage Behavior of Sepidrud Dam Basin Sediments in Fired Clay Bricks.”, 4th International Conference on Geotechnical Engineering and Soil Mechanics (ICGESM 2010): Tehran, Iran (2-3 November, 2010) (in Persian).

11. Karimian, A. and Jamshidi Chenari, R. (2010): “Anisotropy and heterogeneity of undrained shear strength in natural alluvial deposits.”, 4th International Conference on Geotechnical Engineering and Soil Mechanics (ICGESM 2010): Tehran, Iran (2-3 November, 2010) (in Persian).

12. Akhavan Maroufi, A. and Jamshidi Chenari, R. (2010): “Investigation on settlement behavior of shallow foundation on sand mixed with tire shreds.”, 4th International Conference on Geotechnical Engineering and Soil Mechanics (ICGESM 2010): Tehran, Iran (2-3 November, 2010) (in Persian).

13. Mohammadzadeh Sani, A., Arabani, M., Khodaparast Haghi, A. and Jamshidi Chenari, R. (2010): “Investigation on the effect of nano-clay in geotechnical properties of clayey sand.”, 4th International Conference on Geotechnical Engineering and Soil Mechanics (ICGESM 2010): Tehran, Iran (2-3 November, 2010) (in Persian).

14. Jamshidi Chenari, R., and, Mohafezatkar, A. (2010): “Adjacent building induced settlement reduction in residential constructions.”, In proceeding of Forensic Approach to Analysis of Geohazard Problems: Mumbai, India (14-15 December, 2010).

15. Alizadeh, B., Pourzeinali, S. and Jamshidi Chenari, R. (2011): “Introduction of new relationships between different earthquake magnitude scales in Iran.”, 6th National Congress on Civil Engineering (6NCCE): Semnan, Iran (26 April, 2011) (in Persian).

16. Alinejad Taheri, A., Jamshidi Chenari, R. (2011): “Stochastic vs. Deterministic Analysis in Earthquake Geotechnics.”, In proceeding of Sixth International Conference of Seismology and Earthquake Engineering (SEE6): Tehran, Iran (16-18 May, 2011).

17. Haj Jafari, M., Jamshidi Chenari, R., Motamed Chaboki, R. (2011): “Investiation on different methods of Study of Seismic Behaviour of Sheet-Pile Walls.”, In proceeding of Sixth International Conference of Seismology and Earthquake Engineering (SEE6): Tehran, Iran (16-18 May, 2011) (in Persian).

18. Pishgah Gilani, P., Jamshidi Chenari, R., (2011): “Stochastic vs. Deterministic Analysis of Consolidation Problem in Natural Alluvial Deposits.”, In proceeding of GeoRisk, ASCE: Atlanta, USA (26-28 June, 2011).

19. Eslami Kenarsari, A., Oloomi Dodaran, R., Jamshidi Chenari, R., Eslami, A., (2011): “Effect of Vertical Heterogeneity in Soil Strength on Pile Bearing Capacity Prediction from CPT Data.”, In proceedings of the 36th annual conference on deep foundations DFI 36: Boston, USA (18-21 October, 2011).

20. Madandoust, A., Lashtenashie, M. A., Jamshidi Chenari, R. (2011): “Investigation of the location of cutoff walls on the foundation of concrete dams by considering the seepage problem.”, In proceedings of the 10th National Conference on Hyraulic: University of Guilan, Guilan, Iran (23 October, 2011) (in Persian).

21. Lashtenashie, M. A., Jamshidi Chenari, R., Madandoust, A. (2011): “The leak-free surface without using the network resolved (MFS) in the earth dam.”, In proceedings of the 10th National Conference on Hyraulic: University of Guilan, Guilan, Iran (23 October, 2011) (in Persian).

22. Jamshidi Chenari, R., and Sadaghiani, M.H. (February 2012): " Numerical Modeling to Optimize Construction Sequences of Karun 3 Powerhouse Cavern.", In proceedings of 1st International and 3rd National Conference on Dams and hydropower: Tehran, Iran (8-9 February 2012).

23. Zhalehjoo, N., Jamshidi Chenari, R., Ranjbar Pouya, K., (2012): “Evaluation of Bearing Capacity of Shallow Foundations Using Random Field Theory in Comparison to Classic Methods.”, In proceedings of GeoCongress, ASCE, Oackland, California, USA (25-29 March, 2012).

24. Gharibi Chenari, A., Javanmard, M., Jamshidi Chenari, R. and Farokhi, F. (2012): “Evaluation of liquefaction potential of Rasht deposits using in-situ test data.”, 9th International Congress on Civil Engineering (9ICCE): Isfahan, Iran (1-8 May, 2012) (in Persian).

25. Seyedein, M.S., Jamshidi Chenari, R., Eslami, A., (2012): “Investigation on probability Density Function for Cone Penetration Test Data.”, In proceedings of the 2012 International Conference on Geomechanics and Engineering (ICGE 12), Seol, Korea (26-29 August, 2012).

26. Jamshidi Chenari, R., Seyedein, M.S., Faraji, S., Eslami Kenarsari, A., (2012): “Investigation on inherent variability of soil properties from cone penetration test.”, In proceedings of the ISC4, XVI Brazilian Congress of Soil Mechanics and Geotechnical Engineering, 4th International Conference on Geotechnical and Geophysical Site Characterization, Porte de Galinhas, Brazil (18-21 September, 2012).

27. Jamshidi Chenari, R., Davoodi, M.A., Alinejad Taheri, A., (2012): “Effects of Spatial Variability of Soil Properties on Natural Frequency of Natural Soil Deposits.”, In proceedings of the 15th World Conference on Earthquake Engineering (15WCEE), Lisbon, Portugall (24 September, 2012).

28. Khaksar Najafi, E., Jamshidi Chenari, R., (2012): “Numerical study on settlement of shallow foundation supported by geosynthetics reinforced soil.”, In proceedings of the International Conference on Ground Improvement and Ground Control (ICGI 2012), Wollongong, Australia (30-01 October-November, 2012).

29. Mahigir, A., Jamshidi Chenari, R. and Sangi, M. (2012): “Bearing capacity of shallow foundation on anisotropic and heterogenous natural deposits.”, 2nd National Conference on Stracture, Earthquake and Geotechnics: Amol, Iran (23 November, 2012) (in Persian).

30. Jamshidi Chenari, R., Aminzadeh, S., Ramezani, S., (2013): “Response of a deterministically inhomogeneous layered media to harmonic excitations.”, In proceedings of the 3rd International Conference on Geotechnical Engineering (new Developments in Analysis,Modeling and Design), Hammamet, Tunisia (21-23 February, 2013).

31. Alizadeh, B., Pourzeinali, S. and Jamshidi Chenari, R. (2013): “Site Specific Design Response Spectra for Bandar-e-Anzali Area.”, 7th National Congress on Civil Engineering (7NCCE): Zahedan, Iran (7 May, 2013) (in Persian).

32. Pishgah Gilani, P., Jamshidi Chenari, R., (2013): “Reliability measures for consolidation settlement by means of data.”, In proceedings of the GEO MONTREAL 2013, Montral, USA (30-02 September-October, 2013).

33. Tizpa, P., Karimpour Fard, M. and Jamshidi Chenari, R. (2013): “Permeability prediction by artficial neural networks.”, 1st Iranian Conference on Geotechnical Engineering: Ardebil, Iran (22-23 October, 2013) (in Persian).

34. Ghorbani, A., Jamshidi Chenari, R., Kamyab Farahbakhsh, H. and Mirabasi, F. (2013): “Bearing capacity ratios of piled-raft system in clay deposits using FLAC 3D.”, 1st Iranian Conference on Geotechnical Engineering: Ardebil, Iran (22-23 October, 2013) (in Persian).

35. Heshmati, S., Jamshidi Chenari, R., Shahnazari, H. and Karimpour Fard, M. (2014): “Laboratory investigation on variation of shear strength of Sepidrud dam basin sediments using UC, Miniature Vane and Pocket Penetrometer devices.”, 1st National Congress on Construction Engineering and Projects Assessment: Gorgan, Iran (22 April, 2014) (in Persian).

36. Pourghafar Maghfarati, S., Jamshidi Chenari, R. and Karimpour Fard, M. (2014): “Hydraulic conductivity of sand mixed with compressible material like EPS, tire crumbs in large Oedometer apparatus.”, 1st National Congress on Construction Engineering and Projects Assessment: Gorgan, Iran (22 April, 2014) (in Persian).

37. Ghorbani, A., Jamshidi Chenari, R., and Mirabasi, F. (2014): “Investigation on pile length effect on bearing capacity ratios of piled-raft system in clay deposits using FLAC 3D .”, 8th National Congress on Civil Engineering (8NCCE): Babol, Iran (7th May, 2014) (in Persian).

38. Alizadeh, B., Pourzeinali, S. and Jamshidi Chenari, R. (2014): “PGA in Different Seismicity Levels for Bandar-e-Anzali Area Using the New Correlation Relatons Magnituide Scales.”, 8th National Congress on Civil Engineering (8NCCE): Babol, Iran (7th May, 2014) (in Persian).

39. Jamshidi Chenari, R., Lashteneshaie, M. A., Atashbahar, M. (2014): “Evaluation of the Behavior of Well and Uniformly Graded Rockfill Material Using Large-Scale Triaxial Tests.”, 15th Civil Engineering Students Conference (CESC15): Urmia, Iran (2-4 September, 2014) (in Persian).

40. Shamsi Sosahab, J., Jamshidi Chenari, R., and Karimpour Fard, M. (2014): “Analysis of Piled-Raft Foundation in Clay using Analytcial and Numerical Methods.”, 15th Civil Engineering Students Conference (CESC15): Urmia, Iran (2-4 September, 2014) (in Persian).

41. Shamsi Sosahab, J., Karimpour Fard, M., and Jamshidi Chenari, R. (2014): “Numerical Modelling of Piled-Raft Foundation in Clay Material.”, 15th Civil Engineering Students Conference (CESC15): Urmia, Iran (2-4 September, 2014) (in Persian).

42. Jamshidi Chenari, R., Lashteneshaie, M. A. and Atashbahar, M. (2014): “Evaluation of the Behavior of Rockfill Material Using Large-Scale Triaxial Tests.”, 2nd Iranian Conference on Geotechnical Engineering (2ICGE): Kermanshah, Iran (1st October, 2014) (in Persian).

43. Tizpa, P., Aslmand, S.H., Jamshidi Chenari, R. and Karimpour Fard, M. (2014): “Investigation of the effect of grain size distribution on permeability of sand-clay mixtures.”, 2nd Iranian Conference on Geotechnical Engineering (2ICGE): Kermanshah, Iran (1st October, 2014) (in Persian).

44. Veiskarami, M., Jamshidi Chenari, R. and Jameei, A.A. (2014): “Effect of Soil Shear Strength Parameters Anisotropy on the Bearing Capacity of Surface Footings.”, 1st National Conference on Soil Mechanics and Foundation Engineering: Shahid Rajaie University, Tehran, Iran (3-4 December, 2014) (in Persian).

45. Pakdaman, M., Karimpour Fard, M. and Jamshidi Chenari, R. (2014): “Dynamic behavior of sand-tire crumbs mixture in laminar box on shaking table.”, 1st National Conference on Soil Mechanics and Foundation Engineering: Shahid Rajaie University, Tehran, Iran (3-4 December, 2014) (in Persian).

46. Eslami Kenarsari, A., Jamshidi Chenari, R. (2015): “Probabilistic Settlement Analysis of Shallow Foundations on Heterogeneous Soil Stratum with Anisotropic Correlation Structure.”, International Foundations Congress and Equipment EXPO (IFCEE 2015), San Antonio, Texas, USA (17-21 March, 2015).

47. Veiskarami, M., Jamshidi Chenari, R. and Jame’ei, A.A. (2015): “Effect of Soil Shear Strength Parameters Anisotropy on the Bearing Capacity of Surface Footings.”, In proceedings of 10th International Congress on Civil Engineering, University of Tabriz, (5-7 May, 2015).

48. Karimpour Fard, M., Jamshidi Chenari, R., Shamsi Soshab, J., Jamshidi Chenari, M. and Douzandeh Nargesi, E. (2015): “Experimental and numerical modeling of load-displacement behavior of raft foundation in large rigid box.”, In proceedings of 10th International Congress on Civil Engineering, University of Tabriz, (5-7 May, 2015) (in Persian).

49. Soltankhah, S., Karimpour Fard, M. and Jamshidi Chenari, R. (2015): “Dynamic Properties of Soil Reinforced with Young Vetiver.”, In proceedings of National Conference on Civil Engineering and Architecture with Focus on Sustainable Development, Fouman and Shaft Islamic Azad University, (13th August, 2015) (in Persian).

50. Poursalimi, N. and Jamshidi Chenari, R. (2015): “Dynamic behavior of sand mixed withtire crumbs using large cyclic direct shear test apparatus.”, In proceedings of 2nd International Conference on Geotechnical & Urban Earthquake Engineering,Tabriz , Iran (7-9 September 2015).

51. Kouhneshin, E., Ebrahimi Khonachah, R. and Jamshidi Chenari, R. (2015): “Investigation of cyclic behavior of EPS-sand mixtures using large direct shear apparatus.”, In proceedings of 2nd International Conference on Geotechnical & Urban Earthquake Engineering,Tabriz, Iran (7-9 September 2015).

52. Atashbahar, M. and Jamshidi Chenari, R. and Lashteneshaei, M.A. (2015): “Evaluation of the Behavior of Rockfill Material Using Large-Scale Triaxial Tests.”, In proceedings of 2nd International Conference on Geotechnical & Urban Earthquake Engineering,Tabriz , Iran (7-9 September 2015).

53. Atashbahar, M., Jamshidi Chenari, R. and Lashteneshaei, M.A. (2015): “Evaluation of the Particle Crushing of Rockfill Materials Using Marsal Failure Criterion.”, In proceedings of 2nd Iranian Conference on Soil Mechanics and Foundation Engineering, University of Qom, Iran (14-15 October, 2015) (in Persian).

54. Riahi, P., Jamshidi Chenari, R. and Karimpour Fard, M. (2015): "Mechanical properties of sand-TDA mixtures in large scale direct shear test." In proceedings of Geotechnical Engineering for Infrastructure and Development: XVI European Conference on Soil Mechanics and Geotechnical Engineering, Edinburgh, Scotland, September, 2015, pp.3323-3328.

55. Jamshidi Chenari, R. and Bakhshipour, S. (2016): “Laboratory Investigation on the Effect of Waste Plastic Strips on Strength Properties of Sand Materials.”, In proceedings of 3rd National and 1st International Conference in Applied Research on Civil Engineering,

Architecture & Urban Planning, K.N University of Technology, Iran (9-10 March, 2016) (in Persian).

56. Ghoreishi, S. M., Taleb, S. A. and Jamshidi Chenari, R. (2016): “Laboratory Modeling of the Inherent Heterogeneity of Soils Using Random Field Theory.”, In proceedings of International Conference on Civil Engineering, Tehran University, Iran (27 May, 2016) (in Persian).

57. Shafie, S. E., Jamshidi Chenari, R. and Zakeri, P. (2016): “Deformation Characteristics of Sand–Geofoam Composite using large oedometer apparatus.”, In proceedings of First International Comprehensive Competition Conference on Engineering Sciences in Iran, Anzali, Iran (September, 8, 2016) (in Persian).

58. Ghorbani, A., Jamshidi Chenari, R. and Nasiri Alamooti, M. (2016): “Evaluation of strength properties of cement stabilized sand mixed with EPS beads and fly ash.”, In proceedings of 3rd International Conference on Civil Engineering, Architecture and Urban Economy Development, Shiraz, Iran (December, 15, 2016) (in Persian).

59. Nasiri, A. and Jamshidi Chenari, R. (2016): “Evaluation of 1-D seismic site response modeling of sand using shaking table experiments.”, In proceedings of 4th International Congress on Structure, Architecture and Urban Development, Shahid Beheshti University, Tehran, Iran (December, 27-29, 2016).

60. Ghorbani, A., Jamshidi Chenari, R. and Nasiri Alamooti, M. (2017): “Evaluation of strength of Chamkhaleh sand mixed with EPS, fly ash and cement.”, In proceedings of 2nd National Conference on Sustainable Development of Kohgiluyeh and Boyer-Ahmad Province, Yasooj, Iran (March, 2-3, 2017) (in Persian).

61. Jamshidi Chenari, R., Jamali, N. and Veiskarami, M. (2017): “Analytical and Numerical Study of the Elastic Settlement of Surface Footings on Anisotropic Materials.”, In proceedings of 10th National Congress on Civil Engineering, Sharif University of Technology, Tehran, Iran (April, 19-20, 2017) (in Persian).

62. Veiskarami, M., Jamshidi Chenari, R., Ahmadi, M. A. and Hatefi, M. H. (2017): “Variations of the Passive Earth Pressure on Rigid Retaining Walls During the Earthquake.”, In proceedings of 10th National Congress on Civil Engineering, Sharif University of Technology, Tehran, Iran (April, 19-20, 2017) (in Persian).

63. Firoozfar, A.R., Jamshidi Chenari, R. and Attari, S. (2017): “Application of EPS Geofoam in Civil Engineering and its Environmental Impact.”, In proceedings of 1st National Conference of Ideas and New Technologies in Geographical Sciences, University of Zanjan, Zanjan, Iran (September, 20, 2017) (in Persian).

64. Hosseinzadeh, H. R., Jamshidi Chenari, R., and Veiskarami, M. (2017): “Effect of Anisotropy on Shear Strength of Particulate Materials-Case Study: Chamkhaleh Sand.”: 5th International Congress on Civil Engineering, Architecture, and Urban Development, 26-28 December 2017, Shahid Beheshti University, Tehran, Iran (in Persian).

65. Jamshidi Chenari, R., Pakdel, P. and Veiskarami, M. (2017): “The Third Bearing Capacity Factor of Shallow Foundations Considering the Footing-Soil Roughness Effect.”: 5th International Congress on Civil Engineering, Architecture, and Urban Development, 26-28 December 2017, Shahid Beheshti University, Tehran, Iran (in Persian).

66. Ghollasi Mood, A., Jamshidi Chenari, R., Veiskarami, M., and Ahmadi, H. (2018): “Study on the Effect of Geofoam Barriers in Reducing the Induced Vibrations due to Adjacent Machine Foundation.”, In proceedings of 8th International Conference on Acoustics and Vibration, December 4-5, Shahid Beheshti University, Tehran, Iran (in Persian).

67. Rezaie, B., Jamshidi Chenari, R., and Veiskarami, M. (2018): “Evaluation of the EPS effect on lateral resistance force on retaining walls by using physical modelling.”: International Conference on Civil Engineering, Architecture, and Urban Management in Iran, December 2018, Tehran University, Tehran, Iran (in Persian).

68. Ghollasi Mood, A., Jamshidi Chenari, R., Ahmadi, H., and Veiskarami, M. (2018): “Investigating the induced vibration amplitude of a surface strip foundation adjacent to a machine foundation under impact load.”: International Conference on Civil Engineering, Architecture, and Urban Management in Iran, December 2018, Tehran University, Tehran, Iran (in Persian).

69. Foroutan Kalourazi, A., Veiskarami, M., Jamshidi Chenari, R., and Izadi, A. (2018): “Effect of Cohesion Anisotropy on the Bearing Capacity of Surface Footings Near

Slopes.”: International Conference on Civil Engineering, Architecture, and Urban Management in Iran, December 2018, Tehran University, Tehran, Iran (in Persian).

70. Hemmati Masuoleh, F., Saleh Jalali, R., Jamshidi Chenari, R., and Ghorbani, A. (2018): “FDM Site Response Analysis of Anisotropic Deposits under Inclined SH Waves.”: International Conference on Civil Engineering, Architecture, and Urban Management in Iran, December 2018, Tehran University, Tehran, Iran (in Persian).

71. Safardoost Siahmazgi, A.H., Jamshidi Chenari, R., and Veiskarami, M. (2019): “Seismic bearing capacity of strip footing under pseudo-dynamic loads using lower bound limit analysis method.”, In proceedings of 11th National Congress on Civil Engineering, April 30-May 1, Shiraz University, Shiraz, Iran.

72. Khazaie, A., Jamshidi Chenari, R., and Veiskarami, M. (2019): “Bearing Capacity of a Strip Footing Adjacent to a Machine Foundation Using Finite Element Limit Analysis.”, In proceedings of 11th National Congress on Civil Engineering, April 30-May 1, Shiraz University, Shiraz, Iran.

73. Fathipour, H., Veiskarami, M. and Jamshidi Chenari, R. (2019): “Evaluation of active and passive seismic earth pressures against retaining walls using finite element and limit analysis.”, In proceedings of 11th National Congress on Civil Engineering, April 30-May 1, Shiraz University, Shiraz, Iran.

74. Kazempour, S., Jamshidi Chenari, R., and Ahmadi, H. (2019): “Experimental investigation on the effect of particle size on deformation characteristics of EPS-sand composites.”, In proceedings of 11th National Congress on Civil Engineering, April 30-May 1, Shiraz University, Shiraz, Iran (in Persian).

75. Dastpak, P., Mousavi, S., Jamshidi Chenari, R., Brigid, C., and Javankhoshdel, S. (2019): “A general probabilistic analysis of simple reinforced slopes using RLEM approach.”, In proceedings of GeoStJohn’s 2019, 72nd Annual CGS Conference, Newfoundland, Canada (September 29-October 2, 2019).

76. Izadi, A., Jamshidi Chenari, R., Brigid, C. and Javankhoshdel, S. (2020): “Pseudo and Full Stochastic Slope Stability Analyses using Random Limit Equilibrium Method (LEM).”, In proceedings of GeoCongress, ASCE, Minneapolis, Minnesota, USA (25-28 February, 2020).

Thesis Supervisions and Advisory (PhD)

1. Alaie, Reza (2018), “Evaluation of Dynamic Properties of Dry Sand-EPS Mixture Using a Shaking Table Apparatus”, PhD Dissertation, Faculty of Engineering, University of Guilan, Guilan, Iran.

2. Haidarie Golafzani, Sara (2018), “Reliability Based Determination of Piles Bearing Capacity Using CPTu Records”, PhD Dissertation, Faculty of Engineering, University of Guilan, Guilan, Iran.

Thesis Supervisions and Advisory (MSc)

1. Oloomi Dodaran, Ramin (2010), “Investigation on shallow foundations settlement by comparing finite element method results with classical computations”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

2. Khaksar, Elmira (2010), “Investigation of Damages due to Interaction between Soil and Water on Structures and their Optimal Control Methods”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

3. Khosravizadeh, Mostafa (2010), “Evaluation of Slope Stability using Classic and Modern Approaches.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

4. Asadollahi, Seyed Mehdi (2010), “Evaluation of Stress Distribution under Footings with Emphasis on Soil-Foundation Interaction.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

5. Alizadeh, Behrooz (2011), “Earthquake Hazard Analysis for Determination of Peak Ground Acceleration in Anzali and Suburb.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

6. Karimian, Akram (2011), “Stochastic Modeling of Bearing Capacity of Shallow Foundations in Cohesive Soils Using Random Finite Element Method”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

7. Rabanifar, Hakimeh (2011), “Valorization of Sepidrud Dam Basin Sediments in Fired Clay Bricks”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

8. Gholipour Salimi, Mastoureh (2011), “Investigation of Seismic Stability of Gravity Quay Walls, Using Numerical Models”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

9. Shahbazi Fashtali, Hamed (2011), “Evaluation of the effect of carpet fiber inclusion on permeability and liquefaction of sandy soils using laboratory tests”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

10. Akhavan Maroufi, Mohammad Ali (2011), “Compressibility of Coarse-Grained Soils Reinforced with Waste Tire Shreds Using Random Finite Element Method (RFEM)”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

11. Mohafezatkar Sareshkeh, Abolfazl (2011), “Adjacent Building Induced Settlement Reduction in Residential Constructions”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

12. Haj Jafari, Majan (2011), “Numerical Study on Seismic Behaviour of Sheet-Pile retaining Walls”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

13. Saghari, Reza (2011), “Numerical Study on static Behaviour of Sheet-Pile Retaining Walls”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

14. Madandoust, Amir (2011), “Numerical Study on Static Behaviour of Sheet-Pile Retaining Walls”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

15. Mohammadzadeh Sani, Abolfazl (2011), “Laboratory Investigation of Nano-Clay Effect on Engineering Properties of Sandy Soils.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

16. Gharibi Chenari, Arman (2011), “Evaluation of Liquefaction Potential of Rasht using Site Investigation Data”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, The University of Zanjan, Zanjan, Iran.

17. Pishgah Gilani, Pouya (2012), “Consolidation Behavior of Heterogeneous Alluvial Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

18. Alinejad Teheri, Amin (2012), “Effects of Heterogeneity on Dynamic Response of Natural Alluvial Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

19. Esfandiari, Mohammad Bagher (2012), “Effect of Carpet Fiber Inclusion on Seepage of Granular Soil, Using Random Finite Element Method”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

20. Behfar, Behroo (2012), “Evaluation of Heterogeneity and Anisotropy in Permeability of Natural Deposits in Seepage through Dams Foundation”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

21. Alaie, Reza (2012), “Slope Stability Analysis in Heterogeneous and Anisotropic Soils using Random Field Theory”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

22. Pourvahedi Roushandeh, Somayeh (2012), “Influence of Anisotropy in Deformation Characteristics of Heterogeneous Natural Deposits in Settlement of Shallow

Foundations”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

23. Fathi, Hamed (2012), “Study On The Compressibility of Coarse-Grained Soils Reinforced with Waste Tire Shreds In Quick Tank”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, Islamic Azad University of Zanjan, Zanjan, Iran.

24. Yousefi Barandagh, Arash (2012), “Effect of Carpet Fiber Inclusion on Seepage of Granular Soil, using Random Finite Element Method”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

25. Seyedein, Maryem Sadat (2012), “Characterization of Stochastic Properties of CPT Data”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

26. Faraji, Sahar (2012), “Effect of Spatial Variability in Soil Strength on Bearing Capacity Prediction of Piles from CPT Data”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

27. Zamanzadeh, Masoud (2012), “Critical Excavation Depth Evaluation in Heterogeneous Soils using Random Field Theory”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

28. Mohseni, Shahrzad (2012), “Evaluation of the Soil-Foundation Interaction in Natural Heterogeneous Alluvial Deposits using Random Field Theory”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

29. Rajabi Visrudi, Majid (2012), “Zonation Map For Assessment of Bearing Capacity of Shallow Foundations in Rasht City”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

30. Bakhshalizadeh, Nima (2012), “Evaluation of Physical and Mechanical Specifications of Silty Soils Mixed with Glass Powder”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

31. Mahigir, Ali (2012), “Evaluation of the Effect of Anisotropy in Shear Strength on Bearing Capacity of Shallow Foundation using Random Field Theory”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

32. Zhelehjoo, Negin (2013), “Evaluation of Bearing Capacity of Shallow Foundations Using Random Field Theory in Comparison to Classic Methods”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

33. Ranjbar Pouya, Kaveh (2013), “Evaluation of Site Heterogeneity Effects on the Filtration of Seismic waves”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

34. Pourghasem Sostani, Ebrahim (2013), “Investigation of Saturated Sand in Anzali Coastal Area using In-situ Test Results and Comparing with FLAC Software to Assess the Liquefaction Potential”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

35. Sadeghnejad Limoui, Mostafa (2013), “Numerical Evaluation of Linear Visco- Elastic Behavior of Glasphalt Pavement”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

36. Jamlbashi, Mohsen (2013), “A Numerical Model to Predict Load-Displacement Behavior of Deep Foundations by Discrete Element Method and CPT Data”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

37. Tizpa, Parichehr (2013), “Evaluation of Geotechnical Properties of Soils Based on Granulometry and Atterberg Limit Tests”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

38. Soheili, Farid (2013), “Mechanical Behavior of Sand-Geofoam Mixtures subjected to Static Loading Using a Large Scale Direct Shear Test Apparatus”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

39. Moradi, Amir (2013), “Estimation of Deformation Characteristics of Geo-foam and Sand-Geofoam Mixtures using Large Triaxial and Oedometer Apparatus”, In partial

fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

40. Navari, Shahram (2014), “Evaluation of Geotechnical Properties of Reclaimed Lands due to Soils Improvement in Bandar Anzali Port”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

41. Aminzadeh Bostani Taleshani, Shirin (2014), “Analytical Solution on Site Response in Heterogeneous Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

42. Pakdaman Ghadimi, Mojtaba (2014), “Evaluation of Dynamic Properties of Sand-Granulated Tire Mixtures using Large Scale Laminar Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan,Guilan, Iran.

43. Yazdanpanah, Reza (2014), “Mechanical Behavior of Mixtures of Sand-Crumb Rubber under Static Loading using a Large-Scale Direct Shear Apparatus”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

44. Heshmati, Sogol (2014), “Stability Investigation on Open Cuts in Clay Deposits using Centrifuge Modelling”, In partial fulfillment of the requirements the degree of master ofscience, Faculty of Pardis, University of Guilan, Guilan, Iran.

45. Shafie, Javad (2014), “Evaluation of Bearing Capacity of Sand-Shreded Tire Mixtures using Large Scale Laminar Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

46. Mashayekhi, Milad (2014), “Evaluation of Bearing Capacity of Sand-Shreded Tire Mixtures using Large Scale Laminar Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

47. Aslmand, Seyed Hossein (2014), “The Hydraulic Conductivity of Sand-Clay Mixture, Evaluating the Effect of Compaction Effort and Side of Compaction”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

48. Riahi, Pedram (2014), “Effect of Displacement Rate on the Strength Parameters of Sand-Granulated Tire Mixtures Using a Large-Scale Direct Shear Test Apparatus”, Inpartial fulfillment of the requirements the degree of master of science, Faculty of Pardis,University of Guilan, Guilan, Iran.

49. Nouruzi Kharati, Hadi (2014), “Experimental Investigation of the Dynamic Behavior of Sand and Rubber Powder by Large-Scale Laminar Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan,Guilan, Iran.

50. Ghorbanpour Akbarabadi, Aref (2014), “Evaluation of Bearing Capacity of Sand- Tire Powder Mixtures using Large Scale Laminar Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan,Guilan, Iran.

51. Pourghaffar Maghfaratei, Sabina (2014), “Evaluation of Hydraulic Conductivity Coefficient of Granulate Mix with Material like Powder Tire and Shredded Tire using a Large Oedometer Apparatus”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

52. Namdar, Saed (2014), “Experimental study on Dynamic Behavior of Sand – Tire Shred mixtures using Large Scale Simple Shear Test Apparatus”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan,Guilan, Iran.

53. Boorang, Pooneh (2014), “Zonation Map For Assessment of Liquefaction Potential of Soil in Rasht City”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

54. Mirabbasi, Seyedeh Fazeleh (2014), “3-Dimenstional Evaluation of Piled-Raft Foundation Bearing Capacity Located on Heterogeneous Soils using Random Field Theory.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

55. Seyed Noori, Niloofar (2014), “Analytical Investigation on Consolidation of Heterogeneous Natural Alluvial Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

56. Atashbahar, Mojtaba (2014), “Evaluation of Mechanical Behaviour of Rockfill Materials in Guilan Rockfill dams”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

57. Jame’ei, Amir Arsalan (2015), “Formulation and Application of the Finite Element andLinear Programming Method for Stability Analysis of Anisotropic Soils”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering,University of Guilan, Guilan, Iran.

58. Shamsi Sosahab, Javad (2015), “Physical Modeling of Bearing capacity of Piled Raft Foundations on Clay Soil in Large-Scale Rigid Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

59. Azadegan, Azadeh (2015), “Numerical Analysis of Buried Steel Pipelines under Seismic Loads in Slopes”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

60. Fakouri Moridani, Farzad (2015), “Effect of Type, Size and Soil Composition on the Hydraulic Conductivity of Soil Contaminated with Heavy Oil and Gas Oil.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

61. Eslami, Reza (2015), “Effect of Type, Size and Soil Composition on the Hydraulic Conductivity of Soil Contaminated with Water and Ethanol.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

62. Asadi Bazardeh, Mehrdad (2015), “Effect of Type, Size and Soil Composition on the Hydraulic Conductivity of Soil Contaminated with Gasoline and Alcohol.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

63. Shahpouri, Hamzeh (2015), “Evaluation of Strength of Anzali Port’s Sands in Large-Scale Cyclic Direct Shear Tests”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

64. Darzi Eslam, Rasoul (2015), “Settlement of Clean Sand Deposits in Shaking Table.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

65. Khabazian, Jafar (2015), “Evaluation of Shear Strength Parameters of Gravel-Sand Mixture in Large-Scale Direct Shear Test Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

66. Amini Shad, F. (2015), “Numerical Investigation on Dynamic Behavior of Sand-Granulated Tire Mixtures, Sand-Tire Shred Mixtures and Sand-Geo-foam Mixtures using Large Scale Laminar Box Modeling Results”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

67. Hemmatzad, Milad (2015), “Effect of Displacement Rate on the Strength Parameters of Sand-Tire Chips Mixtures Using a Large-Scale Direct Shear Test Apparatus”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

68. Zabihi, Sasan (2015), “Evaluation of Shear Strength Parameters of Soil Contaminated with Gas Oil and Gasoline in Large-Scale Direct Shear Test Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

69. Soltanpour, Reza (2015), “Evaluation of Shear Strength Parameters of Soil Contaminated with Heavy Oil and Alcohol in Large-Scale Direct Shear Test Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

70. Rajabi Matak, Hasan (2015), “Effect of High Displacement Rate on the Strength Parameters of Sand-Tire Crumb Mixtures Using a Large-Scale Direct Shear Test Apparatus”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

71. Jamshidi Chenari, Masoud (2015), “Physical Modeling of Stone Column in Large Scale Rigid Box in Sand”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

72. Soltankhah, Sedigheh (2015), “Dynamic Properties of Soil Stabilized by Young Vetiver”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

73. Douzandeh Nargesi, Emad (2015), “Numerical Modeling of Laboratory Test Results of Bearing Capacity of Stone Columns and Piled-Raft Foundation on Sandy Soils in Large-Scale Rigid Box”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

74. Nouzad, Farshad (2015), “Experimental Investigation on Compression Behavior of Sand Mixed with Tire Shreds”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

75. Poursalimi, Nora (2016), “Hysteresis Behavior of Sand-Tire Crumbs Mixture in Large Cyclic Direct Shear Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

76. Ebrahimi Khonachah, Reza (2016), “Sand-EPS Interaction Behaviour in Large Cyclic Direct Shear Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

77. Koohneshin, Elham (2016), “Cyclic Behaviour of Sand-EPS Mixture in Large Cyclic Direct Shear Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

78. Bakhshipour, Sahar (2016), “Shear Strength of Sand Reinforced with Plastic Waste Strips Using Large Direct Shear Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

79. Nasiri, Arezoo (2016), “Analytical solution on site response in laminar box accounting for hysteresis damping.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

80. Shafie, Seyed Ebrahim (2016), “Estimation of Deformation Characteristics of Sand-Geofoam block Mixtures Using a Large Oedometer Apparatus.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

81. Abedinzadeh, Reza (2017), “Reliability Analysis of Vertical Pull-Out Capacity of Plate Anchors in Clay Soils by 2D Random Field”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, Islamic Azad University, Najafabad Branch, Isfahan, Iran.

82. Yeilaghbeigi, Amir Mehdi (2017), “Critical slip surface optimization of heterogenous slopes using Spencer-intelligent algorithm PSO.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Pardis, University of Guilan, Guilan, Iran.

83. Nasiri, Mohsen (2017), “Evaluation of strength properties of cement stabilized sand mixed with EPS beads and fly ash.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

84. Taleb, Seyed Ali (2017), “Physical modelling of uncertainty in deformation characteristics of soils.”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

85. Ghoreishi, Malahat (2017), “Numerical modelling of uncertainty in shear load-displacement characteristics of cohesive soils using FLAC 3D”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

86. Gohari Lasaki, Ashkan (2017), “Evaluation of shear strength of sand–fly ash mixtures reinforced with polyvinyl alcohol in large-scale direct shear apparatus”, In partial fulfillment of the requirements the degree of master of science, Aryan Institute of Science and Technology, Mazandaran, Iran.

87. Jamali, Nazanin (2018), “An Investigation on the Settlement of Shallow Foundations Resting on Cross-Anisotropic Sands Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

88. Pakdel, Pouneh (2018), “A Study on the Bearing Capacity of Surface Foundations Resting on Cross-Anisotropic Sand Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

89. Hosseinzadeh, Hamid Reza (2018), “Experimental Investigation on Behaviour of Transversly Anisotropic Sand Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

90. Ahmadi Rahimabadi, Mohammad Amin (2018), “Variations of Limiting Passive Earth Pressure Considering the Site Characterization Effects”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

91. Hakimi Basti, Tayebeh (2018), “Dynamic Behavior of Expanded Polystyrene (EPS) Geofoam-Sand Composition Using Shaking Table Test”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Zanjan, Zanjan, Iran.

92. Attari, Shokofeh (2018), “Investigation on Constraint Deformation Properties of Sand-Geofoam Block Composition”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Zanjan, Zanjan, Iran.

93. Foroutan Kalourazi, Ahmad (2019), “Evaluation of the Bearing Capacity of Surface Footings Adjacent to Anisotropic Slopes”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

94. Ghollasi Mood, Ashkan (2019), “Estimation of Elastic Settlement and Displacement Amplitude of Rigid Footings Neighboring Machine Foundations on Sand”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

95. Rezaie, Behzad (2019), “Evaluation of Lateral Pressure of Cement Stabilized Sand Mixed with EPS Beads”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

96. Hemmati Masouleh, Foroogh (2019), “Analytical Solution on Inclined Wave Propagation in Cross-Anisotropic Deposits”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

97. Nazemi Sabet Soumehsaraei, Mahsa (2019), “A Study on the Pseudo-Dynamic Bearing Capacity of Shallow Foundation Resting on Heterogeneous Soil using Approximate Analytical Methods”, In partial fulfillment of the requirements the degree of master of science, Faculty of Engineering, University of Guilan, Guilan, Iran.

Technical Reports

o Jamshidi Chenari, R., and Rooshanzadeh, G. (May. 2001): "Performance Monitoring of Karun 3 Dam and Hydropower Project.”, Technical Report Submitted to Instrumentation Department of SABIR Co.

PRESENTATIONS

o Lecture of Geotechnical Instrumentation, Perse Sanco Company, summer 2002. o Lecture of Magnetic Extensometers for Measuring Settlement in Earth Dams,

Langkawi, Malaysia, Spring 2007.

PROFESSIONAL ORGANIZATIONS:

o Iran's National Elites Foundation (INEF) o Iranian Geotechnical Society (IGS), Tehran, Iran. o Iranian Committee of Large Dams (IRCOLD), Tehran, Iran (Head of Technical

Subcommitte on Dam Surveilance ) o Iranian Society of Rock mechanics (IRSRM), Tehran, Iran. o Construction Engineering Disciplinary Organization, Guilan, Iran.

INTERNATIONAL TRAINING COURSE

o Training on Dam Monitoring and Instrumentation in Soil Instruments Ltd, United Kingdom.

o Training on Dam Monitoring and Instrumentation in SISGeo, Milano, Italy.

PH.D. COURSES:

o Iran University of scince and Technology, Tehran, Iran 2002/2003 Advanced Rock Mechanics, Environmental Geotechnic, Soil Behavior Under Loading, Soil Improvement, Soil Plasticity, Deep Foundation, Artificial Neural Network.

o Amir Kabir University of Technology, Tehran, Iran 2002/2003

Finite Element II in Geotechnic

POST-GRADUATE COURSES:

o Sharif University of Technology, Tehran, Iran 1999/2001 Advanced Soil Mechanics I, Advanced Engineering Mathematics, Numerical Methods I in Geotechnical Engineering, Soil Dynamics, Advanced Soil Mechanics II, Earth & Rockfill Dams, Rock Mechanics, Advanced Foundation Engineering

MAIN PROJECTS IN PH.D. COURSES:

o Finite Element II in Geotechnic 1. Non-Linear Analysis of Geomechanical Materials comprising: Elasto-Plastic Analysis of an Earth Slope and a Trench Using Plaxis Software,

Determination of Critical Height of Earth Slope and Comparing with Limit Equilibrium Analysis results

Updating the Linear Elastic Analysis Program, CSFEP1, Adding the Hyperbola Constitutive Law (Duncan-Chang Model) to It.

2. Dynamic Analysis Based on Direct Integration Method (DIM): Derivation of the Mass Matrix for a CST Element Updating the linear Elastic Analysis Program, PLASTR, Making It Capable for Dynamic

Analysis Based on Direct Integration Method. Use of Updated Program for Dynamic Analysis of a Special Structure and Comparing the

Results with the ANSYS Dynamic Analysis Results. 3. Dynamic Analysis Based on Mode Superposition Method (MSM): Updating the linear Elastic Analysis Program, PLASTR, Making It Capable for Dynamic

Analysis Based on Mode Superposition Method. Use of Updated Program for Dynamic Analysis of a Special Structure and Comparing the

Results with the ANSYS Dynamic Analysis Results.

o Soil Behavior Under Loading

1. Centrifuge Modeling of Reinforced Soil Slope: Germ of the Idea. The Application of the Theory of Modeling to Centrifuge Studies. Literature Reviews in Centrifuge Modeling of Reinforced Soil. Case Study in Centrifuge Modeling of a Geosynthetic Reinforced Slope.

o Advanced Rock Mechanics 1. Numerical Modeling in Rock mechanics Comprising: Finite Difference Method (F.D.M.) Finite Element Method (F.E.M.) Discrete Element Method (D.E.M.) Boundary Element Method (B.E.M.)

MAIN PROJECTS IN POST-GRATUATE COURSES:

Numerical Methods I in Geotechnical Engineering 1. F.D.M. Project Comprising:

Solution of an I.V.P. Equation Using Different Scheme Such as Explicit, Implicit, Crank Nikolson and Comparing with Exact Solution.

Pore Pressure Dissipation in a 1D Consolidation Problem Using Terzaghi Equation. Seepage Beneath a Dam Using Laplace Equation. Wave Propagation Due to Landslide Adjacent to a Reservoir.

2. F.E.M. Project Comprising: Derivation of the Stifness Matrix For an Isoparametric Element. Determination of Displacement and Stresses in a Specific Embankment by F.E.M. Distribution of Hydraulic Head in a Specific Embankment Assuming CST Element.

3. Sotware Learning: Analysis of a Sheet Pile Using the PIZZA Sotware.

Advanced Soil Mechanics II

1. Use of the Results of a Triaxial Test, and Fitting It to Different Constitutive Laws.

RESEARCH INTERESTS:

o Probability and Statictics in Soil Mechanics o Stochastic Stability and Deformation analysis in Soil Mechanics o Earthquake Engineering in Geotechnics o Nonconventional Materials o Retaining Structures o Geosynthetics and Soil Reinforcement o Shaking Table Experiments in Geotechnics o Centrifuge Modelling in Geotechnical Engineering o Suirveillance Monitoring in Soil and Rockfill Structures o Neural Network in Geotechnical Engineering o Numerical Methods in Geotechnical Engineering (FEM & FDM) o Derivation of Constitutive Laws in Modeling Wide Variety Behaviors of

Geomechanic Materials (Soil and Rock)

OTHER EXPERIENCES (Part Time Jobs):

2004 Perse Sanco Company, Tehran, Iran. Technical Advisor (2004-2008)

o Technical Advisor for several projects in the field of Geotechnical Instrumentation which includes: Monitoring of Rock & Earth Fill Dam, Concrete Arch Dam, CFRD, Tunnel and Large Underground Spaces including Galabar Earth Dam, Siahbisheh CFRD Dams, Sangesiah Dam, Likvan Earth Dam, Zolachai Earth Dam, Lar Earth Dam, and Masjed-e-Soleiman Dam.

2003 Sadafzar Company, Tehran, Iran. Technical Advisor (2003-2004)

o Technical Advisor for several projects in the field of Geotechnical Instrumentation which includes: Monitoring of Rock & Earth Fill Dam, Pond Dam, Cuffer Dam including Esfarayen Earth Dam, Seymareh Coffer Dam, Meijaran Asphalt ore Earth Dam, Golestan II Homogeneous Earth Dam, Kohrang Pond Dam, Delvari Concrete Double Arch Dam, Khanabad Earth Dam, Tang-e-Haleh Earth Dam, Siavad Earth Dam, and Tangab Earth Dam.

2001 Perse Sanco Company, Tehran, Iran. Technical Advisor (2001-2003)

o Technical Advisor for several projects in the field of Geotechnical Instrumentation which includes: Monitoring of Rock & Earth Fill Dam, Concrete Arch Dam, Tunnel and Large Underground Spaces including Karun IV Concrete Underground Spaces, Fariman Concrete Dam, Mako Earth Dam, and Doosti Earth Dam.

2000/2001 SABIR Company, Khozestan, Iran. Instrumentation Department.

Instrumentation instalation and monitoring in Karun III dam and Hydroproject which was the biggest hydroproject in size within Middle East, located in south west of Iran.

HONORS AND AWARDS:

o Attained the 53rd Nationwide rating among the 219,410 candidates in Entrance Examination of 1995 in Academic Group of Mathematics and Engineering.

o 1st rating in admission quota of Dist 3 among the 35,071 candidates in Entrance Examination of 1995 in Academic Group of Mathematics and Engineering.

o Ranked 39rd among 8,171 participants in the Master’s Program Entrance Examination of 1999 in the field of Civil Engineering.

o Grand Award and Cash Prize for The Best Student in Iran University of Science and Technology, 2004.

BACKGROUNDS:

o Computer Skills:

1. Application Softwares: FLAC 2 & 3D, ANSYS, UDEC, PLAXIS 2 & 3D, PIZZA, MSEEP, ETABS2000, SAP90, AUTOCAD, MATLAB, MS Office.

2. Programming Languages: Turbo Pascal, Visual Fortran and MATLAB 3. Operating Systems: MS DOS, MS Windows

o Language Spoken: 1. Persian: Native 2. English: Fluent 3. French: Good

INTERESTS & SPORTS:

o Soccer, Hiking, and Swimming. o Travelling & Camping. o Religions o Politics.

PERSONAL PROFILE:

o Date of Birth: 15 September 1976. o Martial Status: Married with Two Childern. o Citizenship: Iranian o Languages: Persian & English

REFERENCES:

The University of Tokyo

Emeritus Prof. Ikuo Towhata, Lecturer

The University of Nevada, Reno, USA Dr. Ramin Motamed, Assistant Professor

The University of Washington Dr. Kamran M. Nemati, Associate Professor

Faculty of Civil, Water and Environmental Engineering, Shahid Beheshti University, Tehran, Iran.

Dr. Ali Noorzad, Associate Professor

Dept. of Civil Engineering, Sharif University of Technology, Tehran, Iran.

Dr. Mohammad H. Sadaghiani, Associate Professor

Dept. of Building, Civil and Environmental Engineering, Amir Kabir University of Technology, Tehran, Iran.

Dr. Kazem Fakharian, Associate Professor

Dept. of Building and Civil Engineering, Iran University of Since and Technology, Tehran, Iran.

Dr. Hossein Ghiassian, Associate Professor

Dept. of Railway Engineering, Iran University of Since and Technology, Tehran, Iran.

Dr. Morteza Gharooni Nik, Associate Professor