Upload
mihai-adrian
View
215
Download
0
Embed Size (px)
Citation preview
8/7/2019 CT350AUsermanual
1/16
8/7/2019 CT350AUsermanual
2/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
Capacitance
Range Accurac Resolution
6.6nF 0.5%+20 1pF
66nF 10pF
660nF 100pF
6.6F 1nF
66F
3.5%+8
10nF
660F 100nF
6.6mF 1F
66mF
5%+8
10F
Thank you for purchasing the CCTV security tester. Please read the manual before using the
CCTV testerPRO, and use properly.
For using the CCTV testerPRO safely, please first read theSafety Informationcarefully in the
manual.
The manual should be kept well in case of reference.
Keep the S/N label for after-sale service within warranty period. Product without S/N label will
be charged for repair service.
If there is any question or problem while using the CCTV testerPRO, or damages occurred on
the product, please contact our technical Department.
The data above is only for reference and any change of them will not be informed in advance.
For more detailed technical inquiries, please feel free to call the Technical Department of our
company.
Products certification:
Ver: STPV1.32 Page.1. Ver: STPV1.32Page.30.
http://www.canwintech.com/cer_en.htmhttp://www.canwintech.com/cer_en.htm8/7/2019 CT350AUsermanual
3/16
8/7/2019 CT350AUsermanual
4/16
8/7/2019 CT350AUsermanual
5/16
8/7/2019 CT350AUsermanual
6/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
4. DC12V 1A power output Lithium Ion Polymer Battery (3.7V DC3000mAh). The device employsadvanced power control
and protection circuit. The device is high power-efficient, energy saving and environmental
protection. It can last 12 hours for normal use after charging for 4 hours.
Power the camera with DC12V(1A) power output from the t ester. It is helpful for demo and testing
where there is no power s upply available.
2.2 CCTV testerPRO Kits
Professional design, light and portability, video display and data control are deliberately
integrated, which makes the instrument so simple, practicable, easy for use that the training is
almost unnecessary for an operator to be s killful.
1. CCTV testerPRO 3. LAN Cable Tester 5. BNC Cable
6. Safety cord
7. RS485 data cable
2. Power Supply (5V 2A) 4. Lithium Ion Polymer Battery 8. Instruction Manual
Notice
a. Dont input any power into the DC12/1A OUTPUT port of the CCTV tester to avoid destroy.
b. Dont output this DC12V/1A power to the power input port of the CCTV tester to avoid destroy.
c. When the requirement of the camera is higher than 1A, the CCTV tester will enter protection
mode. Disconnect all the connections of the CCTV tester and then connect the CCTV tester with
power adaptor to resume the CCTV tester.
5. Audio input testTest the audio input from pickup devices. Connect the tester and pickup device with the audio cable.
Ver: STPV1.32 Page.5. Ver: STPV1.32Page.26.
8/7/2019 CT350AUsermanual
7/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
2 .3 Fro nt Pan e ld. You can get reading from LCD.
NOTE:
The meter will show approximate forward voltage drop of the diode.
If the lead connection is reversed, only figure OL will be display.
H. Capacitance Measuring
WARNING!
To avoid electric shock, be sure the capacitors have been discharged fully before measuring
the capacitance of a capacitor.
a. Connect the black test lead to the COM jack and the red test lead to the jack.
b. Press to select , enter the capacitance measurement. Auto range by press key,
and Manual range by press .
Manual range0.000nF 6.6nF range
00.00nF 66nF range
000.0nF 660nF range
0.000uF 6.6F range
00.00uF 66F range
000.0uF 660F range
1 The power indicator: it lights green while the tester is powered on.
2 The data-reception indicator: it lights red while the data is being received.
3 The data-transmission indicator: it lights red while the data is being
transmitted
4 The charge indicator: it lights red while the battery is being charged. As
the charging is complete, the indicator turns off automatically.
5 The display Icon of battery electricity: it displays the electric quantity
6 Main-menu: it shows main functions of CCTV testerPRO.
7 Sub-menu: Shows and sets the values of functions
0.000mF 6.6mF range
00.00mF 66mF range
c. Before connect test leads across two sides of the capacitor under measurement, be sure that the
capacitor has been discharged fully.
d. You can get reading from LCD.
Ver: STPV1.32 Page.25. Ver: STPV1.32Page.6.
8/7/2019 CT350AUsermanual
8/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
8
Long-pressing it more than 2 seconds to turn on/off the tester;
short-pressing to turn on/off the PTZ controller menu displaying.
9
Menu key: it pops up the main-menu; constant-press it or press the
or key can shift between functions
10
Setup key : press it or press left or right key to enter sub-menu to set the
parameters of functions.
11
Upward : Select the item which will be set or add the value of the
parameter. Tilt the PTZ upward.
12
Leftward : Enter the sub-menu or select the parameter whose value will be
changed. Reduce the value of the parameter. Pan the PTZ left.
13
Rightward : Enter the sub-menu or select the parameter whose value will
be changed. Add the value of the parameter. Pan the PTZ right.
14
Downward : Select the item which will be set or reduce the value of the
parameter. Tilt the PTZ downward.
15
Confirm/Open : Confirm the setting of parameters; open the aperture.
16
Return/Close : Return or cancel while setting parameters of the menu;
close the aperture
17
Near focus: Focus the image nearby.
18
Far focus: Focus the image faraway.
19
TELE: zoom in the image
20
WIDE: zoom out the image
21 Digital multimeter
000.0 K 660K range
0.000 M 6M range
00.00 M 66M range
c. Connect test leads across the resistance under measurement.
d. You can get reading from LCD.
NOTE:
When only the figure OL is displayed, it indicates overrange situation and the higher range has to
be selected.
F. Continuity Testing
WARNING!
When testing the circuit continuity, be sure that the power of the circuit has been shut down
and all capacitors have been discharged fully.
a. Connect the black test lead to the COM jack and the red test lead to thejack.
b. Press to select , enter the continuity test.
c. Connect test leads across two point of the circuit under testing.
d. If continuity exists (i.e., resistance less than about 50),built-in buzzer will sound.
e. You can get reading from LCD.
NOTE:
If input open circuit(or the circuit resistance measured is higher than 660,then the figure OL will
be display.
G. Diode Testing
a. Connect the black test lead to the COM jack and the red test lead to the jack.
b. Press to select , enter the diode testing.
c. Connect test leads across to the anode, the black lead to the cathode of the diode under testing.
Ver: STPV1.32 Page.7. Ver: STPV1.32Page.24.
8/7/2019 CT350AUsermanual
9/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
Manual range 0.000mA 6.6mA range 2 . 4 S i d e v i e w
2 Page.23.
00.00mA 66mA range
22 Reset the default settings of parameters.
23 External power supply (DC, 5V): It is highly recommended to use the equipped power adapter.
24 UTP cable port: Please use together with UTP LAN cable tester.
25 RS232 interface: RS232 communication for the PTZ.
26 Audio input:test the pickup and other audio equipments on the front-end27 DC12V1A power output: output DC12V power for camera
28 Tester speaker
29 Video input (BNC input interface): Inputs the video.
30 Video output (BNC output interface): Outputs the video.
31 RS485/422 Interface: RS485/RS422 communication for the PTZ.
000.0mA 660mA range
00.00A 10A rangeuse 10A socket
c. Connect test leads in series with the load under measurement.
d. You can get reading from LCD.
NOTE:
When only the figure OL is displayed, it indicates overrange situation and the higher range has
to be selected.
When the value scale to be measured is unknown beforehand, set the range selector at the highest
position.
The maximum current of mA socket is 660mA, over-current will destroy the fuse, and will damage
the meter.
The maximum current of 10A socket is 10A, over-current will destroy the meter, and will damage
the operator.
E. Resistance Measuring
WARNING!
When measuring in-circuit resistance, be sure the circuit under test has all power removed and
that all capacitors have discharged fully.
a. Connect the black test lead to the COM jack and the red test lead to thejack.
b. Press to select, enter the measurement. Auto range by press key, and
Manual range by press .
Manual range(connect the red lead to black leads, will display the measure range)
000.0 660 range
0.000 K 6K range
00.00 K 66K rangeVer: STPV1.32Page.8.Ver: STPV1.3
8/7/2019 CT350AUsermanual
10/16
8/7/2019 CT350AUsermanual
11/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
3. OperationB. AC Voltage Measuring
3.1 Power on
WARNING!
You cant input the voltage which more than 660V AC, its possible to show higher voltage,
but its may destroy the inner circuit.
Pay attention not to get an electric shock when measuring high voltage.
Continuously press (at least 2 seconds) to power on/off the CCTV testerPRO. When the CCTV
testerPRO is powered onpress MODE key the main-menu will pop up.
a. Connect the black test lead to the COM jack and the red test lead to the V jack.
b. Press to select U~
, enter the AC voltage measurement. Auto range by press key,
and Manual range by press .
Manual range 0.000V 6.6V range
3.2 Menu & Functions00.00V 66V range
Press MODE key continuously or press the or key to select the function (PTZ controller,
Video settings, Colorbar generator, LAN cable tester, Data monitors, Device setting) and enter
corresponding function setting sub-menu. Press SET key to set the parameters in function sub-menu.
000.0V 660V range
000.0mV 660mV range
c. Connect test leads across the source or load under measurement.
d. You can get reading from LCD. Note: When the CCTV testerPRO is powered on, it will return to the function which is being operated
before it is turned off.NOTE:
When only the figure OL is displayed, it indicates over range situation and the higher range has
to be selected.
1. PTZ controller
Display the input video images. Pan/tilt the P/T unit and zoom
in/ out the image. Setup the controlling parameters like protocol,
communication port, baud rate, PTZ ID, pan/tilt speed; set and
call preset position.
When the value scale to be measured is unknown beforehand, set the range selector at the highest
position.
C. DC Current Measuring
WARNING!
Shut down the power of the tested circuit, then connect the meter with the circuit for
measurement.
a. Connect the black test lead to the COM jack and the red test lead to the mA jack for
a maximum of 660mA current. For a maximum of 10A, move the red lead to the 10A jack.
Ver: STPV1.32 Page.21. Ver: STPV1.32Page.10.
8/7/2019 CT350AUsermanual
12/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
2. Video setting
Adjust the LCD brightness, Contrast, Color saturation.
Video Format and Video level testing
3. Colorbar generator
Output or receive seven different forms of video color bar to
tester monitor, cable or other equipment.
OPERATING INSTRUCTIONA. DC Voltage Measuring
WARNING!
You cant input the voltage which more than 660V DC, its possible to show higher voltage,
but its may destroy the inner circuit.
Pay attention not to get an electric shock when measuring high voltage.
4. Cable tester
Test LAN cable or telephone cable.
The connecting condition and the sequence of wires will be
displayed, as well as the serial number of the cable tester kit.
5.Data Monitor
Captures the protocol from the controlling system and display
command data. It is helpful to debug and maintain RS485
communication.
6.Device setting
Set the parameters of the CCTV testerPRO (Auto power off/
Keypad tone/Language/Brightness/Address search)
a. Connect the black test lead to the COM jack and the red test lead to the V jack.
b. Press to select U, enter the DC voltage measurement. Auto range by press key,
and Manual range by press .
Manual range 0.000V 6.6V range
00.00V 66V range
000.0V 660V range
000.0mV 660mV range
c. Connect test leads across the source or load under measurement.
d. You can get reading from LCD. The polarity of the red lead connection will be indicated along with
the voltage value.
NOTE:
When only the figure OL is displayed, it indicates over range situation and the higher range has
to be selected.
When the value scale to be measured is unknown beforehand, set the range selector at the highest
position.
Ver: STPV1.32 Page.11. Ver: STPV1.32Page.20.
8/7/2019 CT350AUsermanual
13/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
Press 7. Address search
Search the ID of PTZ camera
8. Digital Multimeter
Digital Multimeter performs AD/DC Voltage, AC/DC Current,
Resistance, Continuity, Capacitance and Diode test, Auto /
Manual Range, Data hold, Relative measuring.
button, the tester will search up the ID quickly and continuously(from 1 to 256). When
the ID is searched, the PTZ camera will pan right. At this time, please press any key to stop sear ching
up. Press manual single-step decreasing button, the tester will search up the ID step by step
(from 256 to 1). When the ID is searched, the PTZ came ra will stop panning.
Press button , the tester will search up the ID quickly and continuously(from 256 to 1). When
the ID is searched, the PTZ camera will pan left. At this time, please press any key to stop searching
up. Press manual single-step incremental buttonthe tester will search up the ID step by step
(from 1 to 256). When the ID is searched, the PTZ camera will stop panning.
Press the direction control button to adjust Speed Dome Camera. Press button to quit from the
address-scanning function menu.
3.3 PTZ Controller
Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the
controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set
and call preset position.
The following connections should be confirmed before use
a. The Video In interface of the CCTV testerPRO and t he output interface of camera
b. Data A+ of the CCTV testerPRO and A+ of the PTZ camera or controlling device, data B- of
the instrument and B- of the PTZ ca mera or controlling device
Note: Dont connect communications interface with a circuit the voltage higher than 6V.
3.10 Digital Multimeter
Function Button
Auto range
Data hold
Relative measuring
Function select Manual range
SYMBOLS UDC Voltage Measuring U
~AC Voltage Measuring
ADC CurrentMeasuring A~AC Current Measuring
Resistance Measuring Continuity Testing
Diode Testing Capacitance Measuring
Ver: STPV1.32 Page.19. Ver: STPV1.32Page.12.
8/7/2019 CT350AUsermanual
14/16
8/7/2019 CT350AUsermanual
15/16
8/7/2019 CT350AUsermanual
16/16
CCTV testerPROUsers Manual CCTV testerPROUsers Manual
Call preset-98Run frame Scan
Call preset-99Run Auto scan
out pictures with decreased. The CCTV testerPRO will display Normal when video levels are
1000mV20%, Exceed or Weak will be displayed when video level out of 1000mV20%.
3.5. Colorbar generator (Output video at any mode)
Output or receive seven different forms of video color bar to test
monitor, video cable or other equipment.
a. Press the or key to select the parameter which
we want to change the value.
b. Press the or key to change the value.
3.4. Video Setting c. Press ENTER key to save the change or press RETURN key to give up the change
User can customize the brightness, contrast and saturation of the LCD according to the using
environment , the CCTV tester auto display the format(PAL/NTSC) of video input, and analysis
the input video signal level.
3. 6 Cable Tester
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV testerPRO and cable tester. And then the
connecting status, cable type and the sequence of wires will be displayed, as well as the serial
number of the cable tester kit
a. Press the or key to select the parameter which we want to change the value.
b. Press the or key to change the value. Press ENTER key to save the change
or press RETUR key to give up the change
c. The Video Format and Video Level will be displayed in the lower portion of the screen. If
there is no video signal at the Video IN port of the CCTV TesterPRO, the type of NTSC or
PAL , and Video Level will not be displayed.
Depending on the type of camera connected to the CCTV testerPRO, the Video Format: will
automatically change between NTSC and PAL, and the Video Level will automatically change
between IRE (Institute of Radio Engineers) and mV. NTSC signals measured in IRE units, PAL
signals measured in mV.
The Video Level should be within the indicated range. Levels that are too low will result in a
dim picture with reduced dynamic range. A Video Level that is too high will result in washed
The right picture shows line1-7 are closed, line8 is open and the number of the cable tester box is 255
Straight-through Line Cross Line
Ver: STPV1.32 Page.15. Ver: STPV1.32Page.16.