24
Fiberglass • Stock Wood • Hardwood • Mantles Decorative Capitals • Porch Posts • Softwood Stair Parts • Architectural Crown... Quality columns and millwork Crown... Quality columns and millwork

Crown Columns

Embed Size (px)

Citation preview

Page 1: Crown Columns

Fiberglass • Stock Wood • Hardwood • Mantles Decorative Capitals • Porch Posts • Softwood Stair Parts • Architectural

Crown...

Quality columns

and millwork

Crown...

Quality columns

and millwork

Page 2: Crown Columns

Crown Column & Millwork Product Installations

Page 3: Crown Columns

Subject Page

Round Fiberglass Cast Columns 4Filament Wound Columns 5Square Fiberglass Columns 6Synthetic Capitals & Bases for Fiberglass Columns 7Colonial & Authentic Wood Columns 8Non-Tapered & Square Wood Columns 9Classic Wood Columns 10Synthetic Capitals & Bases for Wood Columns 11Hardwood Classic Columns 12Hardwood Mantle Columns 13Decorative Capitals for Fiberglass & Wood Columns 14 Composite Porch Posts 15Wood Porch Posts 16Softwood Stair Parts 17Architectural Columns 18-20Decorative Capitals for Architectural Columns 21-22Quotation & Ordering 23

Table of Contents

Page 4: Crown Columns

Fiberglass Column Collection --- Round Fiberglass Cast

Page Four

NMIK

J

L

B

A

Fib

ergl

assiberglass columns from Crown Column & Millwork are a satisfying

combination of modern-day technology and low maintenance care. Each column shaft is

produced with the lower one third straight and the upper two thirds tapered, creating a

correct architectural entasis. Entasis, attributed to ancient Greek architecture, is the

slight convex curving of the column shaft resulting in a most pleasing appearance.

Fiberglass columns are available in plain and fluted shafts. Our fluted round columns

are cast fluted, resulting in a crisp, deep and architecturally correct Ionic flute. Fluted

columns are available in a wide range of sizes from 6” through 16” diameter. The columns

are a composition of cast glass-reinforced polymers with exceptional strength and durability.

Priming and painting with an oil-based or latex coating is all that is necessary after

installation. They exceed requirements for flame spread and smoke density (SDA) and

each has a NFPA class A rating and BOCA Type I rating for flame spread and

smoke development.

Non-tapered plain cast columns are available in 8”, 10”, 12” and 14” diameters up

to 16’ in length. All Crown fiberglass columns come with a limited lifetime warranty

for material and workmanship when properly installed.

F

Non-taperedFiberglass

Column withContemporary

Capital & Base

Molding

ROUND FIBERGLASS TAPERED DIMENSIONS

Bottom Neck Above Flute Top Bottom No.

Size Dia. Dia. Bead Bead Width Flute Flute Flutes Lengths

A B N I L K J

6" 55

/8" 51

/2" 31

/4" 1" 5

/16" 1" 10 3

/4" 16 8’

8" 7 5

/8" 6 1

/2" 41

/4" 1"1 1

/16" 1" 10 3

/4" 24 5’6” 8’9’10’

10" 9 5

/8" 8 1

/2" 51

/8" 1" 7

/8" 1" 10 3

/4" 24 8’9’10’12’

12" 11 5

/8" 10 " 57

/8" 1" 1" 1" 10 3

/4" 24 8’9’10’12’14’16’

14" 13 5

/8" 12 " 7 " 11

/8 1" 1" 10 3

/4" 24 8’9’10’12’14’

16" 15 5

/8" 131

/2" 7 1

/2" 1 1

/4" 1 1

/4" 1" 10 3

/4" 24 8’9’10’12’14’16’18’

18" 17 1

/2" 15" 85

/8" 13

/8" * * * * 8’9’10’12’14’16’

FlutedFiberglass

Column withTuscan

Capital &Base

Molding

Page 5: Crown Columns

rown Column’s filament wound offering

includes 14” up to 30” diameters (custom sizes are

also available). The filament wound column defines

easy installation. This lightweight yet strong and

durable product is the best choice for exterior projects

which call for large columns. The winding process

of the column allows for a high concentration of

fiberglass and a lower concentration of resins. The

high content of fiberglass gives this product the

durability and strength required of large exterior

columns. Eliminating the need for a crane to install

this column also makes it an ideal selection. Fib

ergl

ass

Page Five

C

Fiberglass Column Collection --- Filament Wound

A Split Column Kitshould be used to reassemble the split fiberglass or wood column shaft halves.

N

I

B

A

PlainFiberglass

Column withTuscan

Capital & BaseMolding

b c d

q s

SPLITTING OPTIONS

FILAMENT WOUND DIMENSIONS

Bottom Neck Above

Size Dia. Dia. Bead Bead Lengths

A B N I

14" 14" 12" 65

/8" 13

/8" 16’

16" 16" 131

/2" 7 5

/8" 1 11

/16" 8’9’10’12’14’16’18’20’

18" 18" 15" 8 1

/2" 2" 12’14’16’18’20’

20" 20" 17" 93

/8" 21

/8" 18’20’22’24’

22" 22" 18 1

/2" 10 1

/4" 21

/8" 18’20’22’24’

24" 24" 20" 113

/8" 2 19

/16" 18’20’22’24’26’

30" 30" 25" 141

/8" 31

/8" 20’22’24’

LOAD BEARING CAPACITIES

Size SpunCast Filament Wound

*6" 8,000

8" 10,500 *

10" 13,990 *

12" 18,000 *

14" 20,020 20,020

16" 21,945 21,945

18" 25,000 25,000

20" * 30,007

22" * 30,007

24" * 30,007

30" * 30,007

1. All load bearing capacities are based on axial

loads with no moments.

2. Please consult your structural engineer for

wind sheer, uplift, and building code

requirements for your area.

COLUMNS TO SURROUND

STRUCTURAL SUPPORTS

Max. Round Max. Square

Size Support Support

6" 2 1

/2" *

8" 5 1

/4" 311

/16

10" 6 7

/8" 413

/16"

12" 8 7

/16" 57

/8"

14" 10 1

/16" 7 1

/8"

16" 117

/16" 81

/16"

18" 14 1

/4" 10 5

/16"

20" 16 3

/16" 11 1

/2"

22" 18 1

/4" 121

/2"

24" 19 5

/8" 13 1

/16"

30" 24 " 171

/8"

1. Split Columns are non load bearing.

CUT AT BEAD LOSS

When using Decorative Capital

Filament

Size Spun Cast Wound

M M

6" 3 1

/4" *

8" 4 1

/4" *

10" 5 1

/8" *

12" 5 7

/8" *

14" 7 " 6 5

/8"

16" 7 1

/2" 7 5

/8"

18" 8 5

/8" 8 1

/2"

20" * 93

/8"

22" * 10 1

/4"

24" * 113

/8"

30" * 14 1

/8"

Page 6: Crown Columns

Fiberglass Column Collection---Square Columns

S

Fib

ergl

assquare fiberglass columns offer an alternative to the

more traditional round columns. Crown’s plain square

fiberglass columns are made from specially formulated

glass-reinforced polymers with a one-piece shaft

and applied astragal with an attractive capital and

base molding. Crown’s square fiberglass column is

both lightweight and strong, resulting in a column

that is easy to handle, water-resistant and impervious

to moisture-related problems.

Fluted square fiberglass columns are also available

and are produced by the same process as fiberglass

round columns with glass-reinforced polymers. The

astragal is cast on the column; the flutes are crisp, deep

and architecturally correct. Typical options for any

fiberglass column include: cutting at the bead, cutting

to overall length, splitting, and tabbing for reassembly.

Page Six

TUSCAN

ED

C

I

GH

F

SPLITTING OPTIONS

i f g h

J

K

L

B

A

PLAIN & FLUTED LOAD

BEARING CAPACITIES

Load Bearing

Size Capacity

6" 8,000

8" 10,000

10" 10,000

12" 10,000

SQUARE, PLAIN & FLUTED DIMENSIONS

Bottom Top Flute Top Bottom No.

Width Width Width Flute Flute Flutes Lengths

Size A B L K J

6" 51

/2" 51

/2" * * * * 8’9’10’

8" 7 1

/2" 7 1

/2"11

/16" 1" 10 3

/4" 24 8’9’10’

10" 9 1

/2" 9 1

/2"7

/8" 1" 10 3

/4" 24 8’9’10’

12" 11 1

/2" 11 1

/2" 1" 1" 10 3

/4" 24 8’9’10’12’

COLUMNS TO SURROUND STRUCTURAL SUPPORTS

Max. Max. Max. Max.

Round Square Round Square

Size Plain (P) Plain (P) Fluted (F) Fluted (F)

6" 4" 2 1

/2" * *

8" 7" 4" 4 1

/2" *

10" 7 1

/2" 5" 6 1

/2" 4"

12" 9" 6" 8" 5"

SPECIFICATIONS FOR TUSCAN CAPITAL, BASE & ASTRAGAL

BASE CAPITAL ASTRAGAL

Size Plinth Molding Square Round

C D E F G H I

8" 10 1

/4" 1 7

/8" 2 3

/8" 10 1

/4" 1 3

/8" 1" 1"

10" 12 3

/4" 2 3

/8" 2 7

/8" 12 3

/4" 1 3

/4" 1 1

/4" 1"

12" 15 1

/4" 2 7

/8" 3 3

/8" 15 1

/4" 2" 1 3

/8" 1"

Square PlainFiberglass

Column withTuscan

Capital & BaseMolding

Square FlutedFiberglass

Column withTuscan

Capital & BaseMolding

Page 7: Crown Columns

Page Seven

C

Fiberglass Column Collection --- Synthetic Capitals & Bases

Cap

&B

ase

TUSCAN ROUND

CONTEMPORARY

ATTIC BASE

ED

C

I

GH

F

E

D

C

TUSCAN SQUARE

rown fiberglass columns come standard with

a Tuscan capital and base molding and are made

from materials that are water resistant, rot resistant

and impervious to insect infestation. Optional design

styles include the Attic base molding, the Roman

Doric captial and base molding and Contemporary

caps and bases for non-tapered fiberglass columns.

For the more traditional installations, Crown

offers a full range of decorative capitals that can be

viewed on page fourteen of this literature piece.

ROMAN DORIC

E

CGH

E

D

F

C

GH

E

D

F

C

SPECIFICATIONS FOR TUSCAN CAPITAL & BASE

BASE CAPITAL ASTRAGAL

Size Plinth Molding Square Round

C D E F G H I

Fiberglass Cast

6" 8 1

/4" 1 1

/2" 1 3

/4" 7 1

/8" 1 1

/8" 5

/8" *

8" 10 1

/4" 1 7

/8" 2 3

/8" 9 9

/16" 1 3

/8" 1" 1"

10" 12 7

/8" 2 3

/8" 2 7

/8" 11 7

/8" 1 3

/4" 1 1

/4" 1"

12" 15 1

/4" 2 3

/4" 3 1

/4" 14 1

/2" 2" 1 3

/8" 1"

14" 18 3

/4" 3 3

/8" 4" 17 1

/4" 2 3

/8" 1 5

/8"

16" 21 1

/2" 3 7

/8" 4 1

/2" 19 1

/4" 2 3

/4" 1 7

/8"

18" 24 1

/4" 4 1

/4" 5 3

/8" 21 3

/8" 3" 2"

Filament Wound

14" 18 3

/4" 3 3

/8" 4" 17 1

/8" 2 3

/8" 1 5

/8"

16" 21 1

/2" 3 7

/8" 4 1

/2" 19 1

/4" 2 3

/4" 1 7

/8"

18" 24 1

/4" 4 1

/4" 5 3

/8" 211

/2" 3" 2 1

/8"

20" 27" 4 3

/4" 6" 24 1

/4" 33

/8" 2 1

/4"

22" 29 3

/4" 5 1

/4" 6 7

/8" 26 1

/2" 3 3

/4" 2 1

/2"

24" 32 1

/2" 5 3

/4" 7 1

/2" 28 3

/4" 4 1

/8" 2 3

/4"

30" 40 1

/2" 7 1

/4" 9 1

/4" 35 3

/4" 5 1

/8" 3 1

/2"

SPECIFICATIONS FOR ROMAN DORIC CAPITAL & BASE

BASE CAPITAL

Size Plinth Molding Square Round

C D E F G H

Fiberglass Cast

6" 8 1

/4" 1 1

/2" 1 3

/4" 7 1

/8" 11

/8"5

/8"

8" 10 3

/8" 1 1

/8" 27

/16" 9 3

/4" 1 7

/16" 11

/16"

10" 12 15

/16" 2 5

/16" 3 1

/8" 12 5

/16" 1 3

/4" 1 9

/16"

12" 15 3

/16" 2 3

/4" 3 1

/2" 14 3

/4" 2 3

/16" 1 1

/2"

14" 18 11

/16" 3 3

/8" 4 1

/16" 17 1

/2" 2 5

/16" 2 1

/16"

16" 21 1

/2" 3 7

/8" 4 7

/8" 19 7

/8" 2 5

/8" 2 1

/16"

18" 24 3

/8" 4 1

/4" 5 3

/4" 22 1

/4" 3 1

/8" 2 1

/4"

Filament Wound

14" 18 11

/16" 3 3

/8" 4 1

/16" 17 1

/2" 2 5

/16" 2 1

/16"

16" 21 1

/2" 3 7

/8" 4 7

/8" 19 7

/8" 2 5

/8" 2 1

/16"

18" 24 3

/8" 4 1

/4" 5 3

/4" 22 1

/4" 3 1

/8" 2 1

/4"

20" 27" 4 3

/4" 6 1

/4" 25" 4" 2 3

/4"

22" 29 3

/4" 5 1

/4

" 6 3

/4" 27 3

/8" 4 3

/8" 3"

24" 32 1

/2" 5 3

/4" 7 1

/2" 29 3

/4" 4 1

/2" 3 1

/4"

30" 40 1

/2" 7 1

/4" 9 3

/8" 37" 5 7

/8" 4 1

/2 "

SPECIFICATIONS FOR

CONTEMPORARY CAPITAL & BASE

BASE

Size Molding

C E

Fiberglass Cast

8" 10 3

/4" 3 1

/4"

10" 13 3

/8" 3 7

/8"

12" 16 1

/8" 4 1

/2"

14" 18 3

/4" 5 3

/8"

SPECIFICATIONS FOR ATTIC BASE

BASE

Size Plinth Molding

C D E

Fiberglass Cast

6" 8 1

/2" 1 1

/2" 2 7

/16"

8" 10 3

/4" 1 7

/8" 3 1

/4"

10" 13 3

/8" 2 3

/8" 3 7

/8"

12" 16 1

/8" 2 3

/4" 4 1

/2"

14" 18 3

/4" 3 3

/8" 5 3

/8"

16" 21 1

/2" 3 7

/8" 6 1

/4"

18" 24 1

/4" 4 1

/4" 7 1

/8"

Filament Wound

14" 18 3

/4" 3 3

/8" 5 3

/8"

16" 21 1

/2" 3 7

/8" 6 1

/4"

18" 24 1

/4" 4 1

/4" 7 1

/8"

20" 27" 4 3

/4" 8 1

/8"

22" 29 3

/4" 5 1

/4" 9"

24" 32 1

/2" 5 3

/4" 9 15

/16"

30" 40 1

/2" 7 1

/4" 12"

Page 8: Crown Columns

AuthenticWood

Column withTuscanCapital

Page Eight

T

Colonial & Authentic Wood Column Collection

Stoc

kW

oodhe Colonial wood column is the most popular

choice in our stock wood column collection. The

Colonial column is available both plain and fluted

and is manufactured with a double bead molding.

The Colonial column has a gradual straight taper.

The Authentic wood column is also available

plain or fluted and has a double taper approximately

one foot below the top of the shaft. The exaggerated

taper gives the authentic column a distinctive

appearance at the neck molding of the shaft.

Typical options for wood columns include: cutting

at the bead, cutting to overall length, altering flute

length, prime one coat, prime/sand/prime, application

of asphaltum, splitting, and splining for reassembly.

COLONIAL AUTHENTIC

ColonialWood

Column withTuscanCapital M M

IK

IK

J

B

L

A

COLONIAL & AUTHENTIC DIMENSIONS

Bottom Neck Above Flute Above Below No.

Dia. Dia. Bead Bead Width Flute Flute Flutes Lengths

COLONIAL--AUTHENTIC COLONIAL--AUTHENTIC COLONIAL--AUTHENTIC COLONIAL--AUTHENTIC COLONIAL--AUTHENTIC COLONIAL--AUTHENTIC

Size A B M M I I L L K K J J

6" 5 1

/2" 4 3

/4" 3 1

/8" 5 1

/4" 1 3

/8" 1 1

/8" 3

/4" 7

/8" 3 1

/2" 4 1

/2" 10 3

/4" 8" 12 12 8’9’10’

8" 7 1

/4" 6 1

/4" 3 1

/8" 5 1

/4" 1 3

/8" 1 1

/8" 15

/16" 7

/8" 3 1

/2" 4 1

/2" 10 3

/4" 8" 12 16 8’9’10’12’

10" 9 1

/4" 8" 3 1

/8" 5 1

/4" 1 3

/8" 1 1

/8" 15

/16" 7

/8" 3 1

/2" 4 1

/2" 10 3

/4 8" 16 20 8’9’10’12’14’16’

12" 11 1

/4" 9 1

/4" 3 1

/8" 5 1

/4" 1 3

/8" 1 1

/8" 15

/16" 7

/8" 3 1

/2" 4 1

/2" 10 3

/4" 8" 20 24 8’9’10’12’14’16’18’

14" 13 5

/8" 12" * * 1 3

/8" 1 1

/4" 1 1

/8" 1 1

/8" 2 3

/4" 4 1

/2" 5" 3" 24 24 8’9’10’12’14’16’18’20’

16" 15 5

/8" 13 1

/2" * * 1 3

/8" 1 3

/4" 1 1

/4" 1 1

/4" 2 3

/4" 2 1

/2" 5" 3" 24 24 8’9’10’12’14’16’18’20’

18" 17 5

/8" 15" * * 1 3

/8" 1 3

/4" 1 1

/2" 1 1

/4" 2 3

/4" 2 1

/2" 5" 3" 24 24 8’9’10’12’14’16’18’20’22’

20" 19 5

/8" 17" * * 1 3

/8" 1 3

/4" 1 5

/8" 1 1

/4" 2 3

/4" 2 1

/2" 5" 3" 24 24 12’14’16’18’20’22’24’

22" 21 5

/8" 18 1

/2" * * 1 3

/8" 1 3

/4" 1 3

/4" 1 1

/4" 2 3

/4" 2 1

/2" 5" 3" 24 24 12’14’16’18’20’22’24’

24" 23 5

/8" 20" * * 1 3

/8" 1 3

/4" 1 7

/8" 1 1

/4" 2 3

/4" 2 1

/2" 5" 3" 24 4 12’14’16’18’20’22’24’

COLUMNS TO SURROUND

STRUCTURAL SUPPORTS

Maximum Maximum

Round Square

Size Support Support

6" 2 1

/4" *

8" 3 1

/2" *

10" 5 3 1

/2"

12" 6 1

/2" 4 1

/2"

14" 8 1

/2" 6

16" 10 1

/4" 7 1

/2"

18" 11 1

/2" 8 1

/2"

20" 13 3

/4" 9 1

/2"

22" 151

/4" 10 1

/2"

24" 16" 11 1

/4"

1. Split Columns are non load bearing.

CUT AT BEAD LOSS

When using a Decorative Capital

Loss Tuscan Cap.

Size Colonial Authentic Height

M M

6" 3 1

/8" 5 1

/4" 2 3

/8"

8" 3 1

/8" 5 1

/4" 2 3

/8"

10" 3 1

/8" 5 1

/4" 2 3

/8"

12" 3 1

/8" 5 1

/4" 2 3

/8"

1. All larger size columns ( 14 “ + ) are made to

overall length.

LOAD BEARING

Load Bearing

Size Capacity

6" 7,000

8" 10,000

10" 10,000

12" 10,000

14" 10,000

16" 18,000

18" 18,000

20" 18,000

22" 18,000

24" 18,000

1. All load bearing capacities are

based on axial loads with no

moments.

2. Please consult your structural

engineer for wind sheer, uplift,

and building code

requirements.

Page 9: Crown Columns

Non

-Tap

ered

Woo

d

Page Nine

Non-Tapered Wood Column Collection -- Round & Square

These stock round wood columns are not tapered and

are available in plain or fluted styles. They can be pro-

duced with or without a Colonial bead.

Square or boxed wood columns are also available in

plain or fluted styles. Square wood columns are shipped

unassembled (kd) for finished assembly at the job site.

Sizes available are 6”, 8”, 10” and 12”.

MIK

J

A

L

B

COLONIAL

NON-TAPERED

SQUARE

ColonialNon-TaperedColumn with

TuscanCapital & Base

Molding

SquareFluted Wood

Columnwith Tuscan

Capital & BaseMolding

L

B

A

GH

E

D

F

C

NON-TAPERED DIMENSIONS

Above

Bottom Neck Above Optional Flute Flute Below No. of

Size Dia. Dia. Bead Bead Width (w/ Bead) Flute Flutes Lengths

A B M I L K J

6" 5 1

/2" 5 1

/2" 3 1

/8" 1 3

/8"3

/4" 3 1

/2" 10 3

/4" 12 8’9’10’

8" 7 1

/4" 7 1

/4" 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 103

/4" 12 8’9’10’12’

10" 9 1

/4" 9 1

/4" 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 16 8’9’10’12’14’16’

12" 11 1

/4" 11 1

/4" 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 20 8’9’10’12’14’16’18’

14" 13 5

/8" 13 5

/8" * 1 3

/8" 1 1

/8" 2 3

/4" 5" 24 8’9’10’12’14’16’18’20’

16" 15 5

/8" 15 5

/8" * 1 3

/8" 1 1

/4" 2 3

/4" 5" 24 8’9’10’12’14’16’18’20’

18" 17 5

/8" 17 5

/8" * 1 3

/8" 1 1

/2" 2 3

/4" 5" 24 8’9’10’12’14’16’18’20’22’

20" 19 5

/8" 19 5

/8" * 1 3

/8" 1 5

/8" 2 3

/4" 5" 24 12’14’16’18’20’22’24’

22" 21 5

/8" 21 5

/8" * 1 3

/8" 1 3

/4" 2 3

/4" 5" 24 12’14’16’18’20’22’24’

24" 23 5

/8" 23 5

/8" * 1 3

/8" 1 7

/8" 2 3

/4" 5" 24 12’14’16’18’20’22’24’

SQUARE DIMENSIONS

Bottom Top Flute No.

Size Width Width Width Flutes Lengths

A B L

6" 5 1

/4" 5 1

/4" 5

/8" 4 8’10’

8" 7 1

/4" 7 1

/4" 3

/4" 5 8’10’

10" 9 1

/4" 9 1

/4" 13

/16" 6 8’10’12’

12" 11 1

/4" 11 1

/4"7

/8" 7 8’10’12’

SURROUND STRUCTURAL SUPPORT

Maximum Maximum

Size Net Wall Square Round

Width Thickness Support Support

6" 5 1

/4" 5

/8" 4" 1 1

/8"

8" 7 1

/4" 5

/8" 6" 3 1

/4"

10" 9 1

/4" 1" 7 1

/4" 5 1

/4"

12" 11 1

/4" 1" 9 1

/4" 7 1

/4"

COLUMNS TO SURROUND

STRUCTURAL SUPPORTS

Maximum Maximum

Round Square

Size Support Support

6" 2 5

/8" *

8" 4 5

/8" *

10" 6 5

/8" 3 1

/2"

12" 8 5

/8" 4 1

/2"

14" 10 1

/8" 6"

16" 12 5

/8" 7 1

/2"

18" 14 1

/8" 8 1

/2"

20" 15 3

/4" 9 1

/2"

22" 17 3

/4" 10 1

/2"

24" 19 3

/4" 11 1

/4"

1. Split Columns are non load bearing.

SPECIFICATIONS FOR TUSCAN CAPITAL AND BASE

BASE CAPITAL

Size Plinth Molding Square Round

C D E F G H

6" 7 3

/4" 1 1

/4" 1 1

/2" 7 7

/8" 1 1

/4" 1 1

/8"

8" 9 5

/8" 1 1

/4" 1 1

/2" 9 5

/8" 1 1

/4" 1 1

/8"

10" 11 7

/8" 1 1

/4" 1 1

/2" 11 7

/8" 1 1

/4" 1 1

/8"

12" 13 3

/4" 1 1

/4" 1 1

/2" 13 3

/4" 1 1

/4" 1 1

/8"

Page 10: Crown Columns

Page Ten

rown’s Classic wood column is an upgraded

selection to the Colonial and Authentic styles.

Available with a plain or fluted shaft, the Classic

column is manufactured with a one-third straight,

two-third radius taper (correct entasis). The bead

detail is more sophisticated and has an architectural

attractiveness.

Every column shaft is made with finger-jointed

staves for added strength and stability. The staves

are joined using tongue and groove joints with Type

I exterior glues and each shaft is treated with a

wood preservative. All sizes for wood columns

include the standard Tuscan capital, column shaft

and Tuscan base and plinth.

C

Classic Wood Column Collection

ClassicColumn with

TuscanCapital & Attic

BaseMolding

Cla

ssic

Woo

d

MIK

J

A

L

B

CLASSIC

A Split Column Kitshould be used to reassemble the split fiberglass or wood column shaft halves.

b c d

q s

SPLITTING OPTIONS

CLASSIC DIMENSIONS

Bottom Neck Above Flute Above Below No.

Size Dia. Dia. Bead Bead Width Flute Flute Flutes Lengths

A B M I L K J

6" 5 1

/2" 4 3

/4" 3 1

/8" 1 3

/8"3

/4" 3 1

/2" 10 3

/4" 12 8’9’10’

8" 7 1

/4" 6 1

/4" 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 16 8’9’10’12’

10" 9 1

/4" 8 " 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 20 8’9’10’12’14’16’

12" 11 1

/4" 9 1

/4" 31

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 24 8’9’10’12’14’16’18’

14" 13 5

/8" 12" * 1 3

/8" 1 1

/8" 2 3

/4" 5" 24 8’9’10’12’14’16’18’20’

16" 15 5

/8" 13 1

/2" * 1 3

/8" 1 1

/4" 2 3

/4" 5" 24 8’9’10’12’14’16’18’20’

18" 17 5

/8" 15" * 1 3

/8" 1 1

/2" 2 3

/4" 5" 24 8’9’10’12’14’16’18’20’22’

20" 19 5

/8" 17" * 1 3

/8" 1 5

/8" 2 3

/4" 5" 24 12’14’16’18’20’22’24’

22" 21 5

/8" 18 1

/2" * 1 3

/8" 1 3

/4" 2 3

/4" 5" 24 12’14’16’18’20’22’24’

24" 23 5

/8" 20" * 1 3

/8" 1 7

/8" 2 3

/4" 5" 24 12’14’16’18’20’22’24’

COLUMNS TO SURROUND

STRUCTURAL SUPPORTS

Maximum Maximum

Size Round Square

Support Support

6" 2 1

/4" *

8" 3 1

/2" *

10" 5" 3 1

/2"

12" 6 1

/2" 4 1

/2"

14" 8 1

/2" 6"

16" 10 1

/4" 7 1

/2"

18" 11 1

/2" 8 1

/2"

20" 13 3

/4" 9 1

/2"

22" 15 1

/4" 10 1

/2"

24" 16" 11 1

/4"

1. Split Columns are non load bearing.

LOAD BEARING

Load Bearing

Size Capacity

6" 7,000

8" 10,000

10" 10,000

12" 10,000

14" 10,000

16" 18,000

18" 18,000

20" 18,000

22" 18,000

24" 18,000

1. All load bearing capacities

are based on axial loads

with no moments.

CUT AT BEAD LOSS

When using a Decorative Capital

Tuscan

Size Loss Cap. Height

M

6" 5 1

/4" 2 3

/8"

8" 5 1

/4" 2 3

/8"

10" 5 1

/4" 2 3

/8"

12" 5 1

/4" 2 3

/8"

1. All larger size columns ( 14 " + ) are

made to overall length.

Page 11: Crown Columns

Page Eleven

Wood Column Collection---Synthetic Capitals & Bases

Crown stock wood columns come standard

with a Tuscan capital and base molding and

are made from a material that is water resistant,

rot resistant and impervious to insect infestation.

Optional design styles include the Attic base

molding and the Roman Doric base molding.

Decorative capitals of various styles are available

for all sizes of our wood columns and can be viewed

on page fourteen of this literature piece.

Cap

ital

&B

ase

GH

E

D

F

C

TUSCAN CAPITAL

TUSCAN BASE

E

D

C

E

D

C

ROMAN DORIC

BASE

ATTIC BASE

SPECIFICATIONS FOR TAPERED

TUSCAN CAPITAL & BASE

BASE CAPITAL

Size Plinth Molding Square Round

C D E F G H

6" 8" 1 1

/4" 1 1

/2" 7 1

/2" 1 1

/4" 1 1

/8"

8" 9 7

/8" 1 1

/4" 1 1

/2" 9 1

/2" 1 1

/4" 1 1

/8"

10" 11 7

/8" 1 1

/4" 1 1

/2" 11" 1 1

/4" 1 1

/8"

12" 13 3

/4" 1 1

/4" 1 1

/2" 12" 1 1

/4" 1 1

/8"

14" 18 3

/4" 3 3

/8" 4" 17 1

/8" 2 3

/8" 1 5

/8"

16" 21 1

/2" 3 7

/8" 4 1

/2" 19 1

/4" 2 3

/4" 1 7

/8"

18" 24 1

/4" 4 1

/4" 5 3

/8" 21 1

/2" 3" 2 1

/8"

20" 27" 4 3

/4" 6" 24 1

/4" 3 3

/8" 2 1

/4"

22" 29 3

/4" 5 1

/4" 6 7

/8" 26 1

/2" 3 3

/4" 2 1

/2"

24" 32 1

/2" 5 3

/4" 7 1

/2" 28 3

/4 4 1

/8" 2 3

/4"

NON-TAPERED

CAPITAL

Square Round

F G H

7 7

/8" 1 1

/4" 1 1

/8"

9 5

/8" 1 1

/4" 1 1

/8"

11 3

/4" 1 1

/4" 1 1

/8"

13 3

/4" 1 1

/4" 1 1

/8"

19 1

/4" 2 3

/8" 1 5

/8"

21 1

/2" 2 3

/4" 1 7

/8"

26 1

/2" 3" 2 1

/8"

28 3

/4" 3 3

/8" 2 1

/4"

31 1

/2" 3 3

/4" 2 1

/2"

33 3

/8" 4 1

/8" 2 3

/4"

SPECIFICATIONS FOR ATTIC BASE

BASE

Size Plinth Molding

C D E

6" 8" 1 1

/4" 2 9

/16"

8" 9 7

/8" 1 1

/4" 3 1

/4"

10" 11 7

/8" 1 1

/4" 3 7

/8"

12" 13 3

/4" 1 1

/4" 4 1

/2"

SPECIFICATIONS FOR ROMAN DORIC BASE

BASE

Size Plinth Molding

C D E

6" 8" 1 1

/4" 1 1

/2"

8" 9 7

/8" 1 1

/4" 1 1

/2"

10" 11 7

/8" 1 1

/4" 1 1

/2"

12" 13 3

/4" 1 1

/4" 1 1

/2"

14" 18 3

/4" 3 3

/8" 4"

16" 21 1

/2" 3 7

/8" 4 1

/2"

18" 24 1

/4" 4 1

/4" 5 3

/8"

20" 27" 4 3

/4" 6"

22" 29 3

/4" 5 1

/4" 6 7

/8"

24" 32 1

/2" 5 3

/4" 7 1

/2"

Page 12: Crown Columns

Page Twelve

ARDWOOD CLASSIC COLUMNS

A quality stain grade column manufactured from select hardwoods such as Red Oak, Cherry,

Maple and Mahogany. Used for interior applications, this column incorporates a tapered shaft

with a true architectural entasis and a classic style bead.

Hardwood classic columns are available either plain or fluted in sizes 8”x8’ through

12”x12’. Time honored craftsmanship and attention to detail set Crown hardwood classic

columns apart as the standard for elegance and beauty.

Hardwood Classic Column Collection

Har

dwoo

d C

lass

icH

Red Oak Cherry Maple Mahogany

MIK

J

L

B

A

CLASSIC

HARDWOOD CLASSIC DIMENSIONS

Bottom Neck Above Flute Above Below No.

Size Dia. Dia. Bead Bead Width Flute Flute Flutes

A B M I L K J

8" 7 1

/4" 6 1

/4" 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 16

10" 9 1

/4" 8" 3 1

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 20

12" 11 1

/4" 9 1

/4" 31

/8" 1 3

/8"15

/16" 3 1

/2" 10 3

/4" 24

See specifications for tapered Tuscan Capital & Base on page Eleven

SIZES

Shaft Wt.

Size (lbs)

8" x 8' 33

8" x 10' 45

8" x 12' 49

10" x 8' 46

10" x 10' 54

10" x 12' 56

12" x 8' 46

12" x 10' 64

12" x 12' 76

Page 13: Crown Columns

Page Thirteen

ARDWOOD MANTLE COLUMNS

A quality stain grade column used in mantle

applications and manufactured from select hardwoods

such as Red Oak, Cherry, Maple and Poplar. This

column incorporates either a tapered shaft with a true

architectural entasis or a non-tapered shaft for a

contemporary appearance. The classic hardwood

column may be purchased with or without a bead

molding, and is available in both a plain or fluted

shaft.

A Crown mantle column is the essential component

in providing natural beauty and pleasing charm to

any mantle installation.

Hardwood Mantle Column Collection

Har

dwoo

d M

antl

eH

MIK

J

L

B

A

GH

E

D

F

C

TUSCAN

MANTLE

MANTLE COLUMN DIMENSIONS

Bottom Neck Above Flute Top Bottom No.

Size Dia. Dia. Bead Bead Width Flute Flute Flute Length

A B M I L K J

TAPERED

3 1

/2" 3" 2 13

/16" 1 1

/4"5

/16"7

/16"5

/16"1

/2" 12 52”

5" 4 1

/2" 3 7

/8" 1 1

/4"5

/16"7

/16" 5

/16" 1

/2" 20 52”

NON-TAPERED

3 1

/2" 3" 3 3

/8" 1 1

/4"5

/16"7

/16" 5

/16" 1

/2" 12 52”

5" 4 1

/2" 4 7

/8" 1 1

/4" 5

/16"7

/16" 5

/16" 1

/2" 12 52”

SPECIFICATIONS FOR TUSCAN CAPITAL AND BASE

BASE CAPITAL

Size Plinth Molding Square Round

C D E F G H

TAPERED

3 1

/2 " 5" 1" 1 1

/4" 4 1

/2" 1 1

/8"5

/8"

5" 6 1

/2" 1" 1 1

/4" 4 1

/2" 1 1

/8"5

/8"

NON-TAPERED

3 1

/2" 5" 1" 1 1

/4" 5" 1 1

/8"5

/8"

5" 6 1

/2" 1" 1 1

/4" 6 1

/2" 1 1

/8"5

/8"

Page 14: Crown Columns

Page Fourteen

Roman Corinthian

Modern CompositeGreek Erectheum Greek Erectheum withNecking

Scamozzi

rown Column & Millwork offers an infinite

selection of specialty items such as decorative capitals,

from a composite mold of marble & polyestor resin.

They can be mounted on either plain or fluted columns

for interior or exterior use. These capitals are true to

their original inspirations and when combined

with todays advanced material technology and

construction methods they form a truely unique product.

Dec

orat

ive

Cap

ital

s

Empire

Roman Ionic

Greek Angular Ionic

C

Decorative Capitals--Fiberglass & Wood Columns

Empire with Necking

Temple of Winds

STOCK ROUND

WOOD

Authentic,Colonial,

Non-tapered or

Classic

Size

6”

8”

10”

12”

14”

16”

18”

20”

22”

24”

STOCK ROUND

WOOD

Authentic,Colonial,

Non-tapered or

Classic

Size

6”

8”

10”

12”

14”

16”

18”

20”

22”

24”

ROUND

FIBERGLASS

Fiberglass Cast

Size

6”

8”

10”

12”

14”

16”

18”

Filament Wound

14”

16”

18”

20”

22”

24”

Page 15: Crown Columns

Page Fifteen

Com

posi

te P

osts

Composite Porch Post Collection

rown’s composite porch posts combine the

latest in materials and technology to provide a low

maintenance product with exceptional detail. The

composite post is load bearing, easy to install, and

backed by a limited lifetime warranty.

The composition of this innovative product is

comprised of a fiberglass outer shell and a center core

of galvanized steel encapsulated with polyurethane

foam. The composite porch post has an immaculate

semi-gloss finish. Painting is not required, however,

if painting is desired a latex or oil-based paint may

be used.

Each post is packaged with two mounting plates

and installation instructions. Fastening kits are also

available and are sold separately.

C

ColonialComposite Post

COMPOSITE FASTENING KIT

Included in each kit are: One(1) skirt, four

(4) brackets, eight(8) TapCon screws for

attaching to wood or concrete substrates

and eight(8) #8 screws. Each kit is sold

separately from post.

COMPOSITE MOUNTING PLATES

Two (2) composite mounting plates

are shipped with each post.

COLONIAL COMPOSITE PORCH POST

Size Base Height

5"x5"x8' 42"

5"x5"x9' 42"

6"x6"x8' 42"

6"x6"x9' 42"

COMPOSITE LOAD BEARING

Actual Load

Size Capacity (lbs)

5"x5"x8' 3500

5"x5"x9' 3500

6"x6"x8' 5000

6"x6"x9' 5000

Page 16: Crown Columns

ColonialPorch Post

ChamferredContemporary

New Orleans Porch Post

Lamp Post

Page Sixteen

Por

ch P

osts

Wood Porch Post Collection

C

WOOD LAMP POST

Weight

Size (lbs)

5"X5"X8' 24

rown’s wood porch and lamp posts add a

distinctive touch to any style home. Porch posts are

often used as supporting elements for porches.

Combined with balusters, hand and shoe rail, and

decorative millwork, porch posts establish the popular

Victorian style.

Crown’s wood porch posts are constructed of select

softwoods, laminated and finger-jointed for greater

strength and stability. The wood porch posts are

available in a variety of sizes and styles.

Cast aluminum plinths are an available option

for providing proper ventilation at the bottom of the

post. Elevating and ventilating the porch post

provides protection from moisture absorption. Uplift

kits are also available.

LOAD BEARING

COLONIAL WOOD

Actual Load

Size Capacity (lbs.)

4"x4"x8' 1200

4"x4"x9' 900

5"x5"x8' 2750

5"x5"x9' 2062

5"x5"x10' 1546

6"x6"x8' 4800

6"x6"x9' 3600

6"x6"x10' 2700

LOAD BEARING

NEW ORLEANS WOOD

Actual Load

Size Capacity (lbs.)

4"x4"x8' 400

4"x4"x9 ' 325

5"x5"x8 ' 1700

5"x5"x9 ' 1350

5"x5"x10' 1050

6"x6"x8 ' 2800

6"x6"x9 ' 2400

6"x6"x10' 2000

LOAD BEARING

CONTEMPORARY

Actual Load

Size Capacity(lbs)

4"x4"x8' 1200

4"x4"x9' 900

5"x5"x8' 2750

5"x5"x9' 2062

5"x5"x10' 1546

6"x6"x8' 4800

6"x6"x9' 3600

6"x6"x10' 2700

LOAD BEARING

CHAMFERRED

CONTEMPORARY

Actual Load

Size Capacity(lbs)

4"X4"X8' 1200

4"X4"X9' 900

5"X5"X8' 2750

5"X5"X9' 2062

5"X5"X10' 1546

6"X6"X8' 4800

6"X6"X9' 3600

6"X6"X10' 2700

CAST ALUMINUM PLINTHS FOR

WOOD PORCH POSTS

Order for

Size Height Use With

3 1

/4" 1" 4" Posts

4 1

/4" 1" 5" Posts

5 1

/4" 1" 6" Posts

ContemporaryPorch Post

Page 17: Crown Columns

Page Seventeen

Softwood Stair Part Collection

ur Softwood Stair Part Collection offers a wide

range of design flexibility while offering a classic addition to

your home. Our hemlock stair parts are manufactured under

highly controlled standards for beauty that will last a

lifetime. All parts are made without the use of finger-joints

and will enhance the appearance of any interior application.

OColonialHandrail

ColonialShoerail

SouthamptonHandrail

Traditional

Colonial

Heritage

Southampton

Contemporary

Contemporary

Southampton

Stai

r P

artsCLEAR HEMLOCK WOOD RAILS

CLEAR HEMLOCK WOOD TOPSCLEAR HEMLOCK WOOD SPINDLES

CLEAR HEMLOCKWOOD NEWELS

2" x 6'

2" x 8'

2" x 16'

3" x 6'

3" x 8'

3" x 16'

2" x 6'

2" x 8'

2" x 16'

3" x 6'

3" x 8'

3" x 16'

2" x 6'

2" x 8'

2" x 16'

TRADITIONAL

4" x 48"

4" x 60"

5" x 48"

5" x 60"

CONTEMPORARY

4" x 48"

4" x 60"

SOUTHAMPTON

4" x 48"

4" x 60"

Turned

Size Area

COLONIAL

2" x 7 1

/2" 5"

2" x 9" 7"

2" x 12" 9"

2" x 18" 9"

2" x 24" 14 1

/2"

2" x 28" 14 1

/2"

3" x 18" 9"

3" x 24" 14 1

/2"

3" x 28" 14 1

/2"

3" x 32" 14 1

/2"

3" x 36" 14 1

/2 "

HERITAGE

2" x 32" 26"

2" x 36" 26"

2" x 48" 32"

3" x 32" 26"

3" x 36" 26"

3" x 48" 32"

SOUTHAMPTON

2" x 32" 17 1

/2"

2" x 36" 17 1

/2"

2" x 42" 17 1

/2"

2" x 48" 17 1

/2"

CONTEMPORARY

2" x 32" *

2" x 36 *

2" x 42" *

2" x 48" *

Size Actual Size

BALL TOP

3" x 5" 2 3

/8" x 4"

4" x 6" 3 1

/8" x 5 3

/4"

5" x 7" 4 1

/8" x 7 5

/8"

6" x 8" 5 1

/4" x 7"

ACORN DROP

6" x 10" 5" x 9"

ROUND TOP

3" x 5" 2 3

/8" x 4"

4" x 6" 3 1

/8" x 5"

6" x 8" 5 1

/4" x 7"

URN TOP

3" x 6" 2 3

/8" x 6 3

/4"

4" x 8" 3 1

/4" x 7 3

/4"

5" x 10" 4 3

/8" x 9"

SOUTHAMPTON TOP

3" x 4" 2 3

/8" x 4"

4" x 5" 3 1

/4" x 4 3

/4"

KENT TOP

3" x 3" 2 3

/8" x 2 1

/2"

4" x 3" 3 3

/8" x 3"

2" x 6'

2" x 8'

2" x 16'

2" x 6'

2" x 8'

2" x 16'

3" x 6'

3" x 8'

3" x 16'

2" x 6'

2" x 8'

2" x 16'

3" x 6'

3" x 8'

3" x 16'

1

1

1 1/4"

2 1/2"

1 5/8"1/4"

1 1/4"

2 1/2"

3 1/4"

2 3/8"

2 1/4"

1 5/8"1/4"

1 1/4"

3 1/4"

2 1/2"

1 1/8

2 1/2"

1 5/8"1/4"

7 5/8"

4 1/8"

1"

7 3/4"

1"

3 1/4"

5"

1"

3 1/8"

4 3/4"

3 1/4"

1"

10"

5"

Acorn Drop

Ball Top

Round Top Urn Top

Kent Top

Southampton Top

Page 18: Crown Columns

Page Eighteen

Architectural Column Collection

Arc

hite

ctur

al

t Crown, our attention to detail and devotion to the classical orders are

absolute. Because our standards are exacting, we produce columns certain to

meet your individual needs, regardless of the shape, size, design, or species

of wood that you require. We closely control the quality and preciseness of

entasis, projections and profiles as our master craftsmen make each

architectural column to your custom specifications.

Through our extensive lumber sources, Crown carries virtually every type

of wood, be it a standard exterior such as Western Red Cedar and Clear

All-Heart Redwood, or an interior paint grade such as finger-jointed pine

or poplar. Crown uses only the best kiln-dried lumber available. Exotic

hardwoods such as teak, mahogany, cherry, walnut and other highly

sought after species are available in unlimited designs.

Premium finishing services are included in the pricing of our custom-made

architectural products. This includes two or

three coats of primer to prepare the surface for

painting at the job site. We precisely trim

each end of the shaft and apply an exterior

treatment of asphaltum paint inside the entire

length of the shaft. We also construct heavy

custom wooden crates to ensure safe transit.

IonicFlutedColumn

with Roman Corinthian

Capital

A

Page 19: Crown Columns

Page Ninteen

Architectural Column Collection

Arc

hite

ctur

al

Design 100P(Plain)100F(Fluted)

Cap: TUSCANBase: TUSCAN

Design 200P(Plain)200F(Fluted)

Cap: GREEK DORICBase: NONE

Shaft Shaft Square Round SquareBottom Top Cap Cap Neck CapDiameter Diameter Height Height Height Width

A B C D E F

8" 6 1/2" 1 3/8" 1 5/8" 1/2" 9 1/4"

10" 8 1/4" 1 3/4" 2 1/16" 5/8" 11 5/8"

12" 9 3/4" 2 1/8" 2 9/16" 3/4" 13 3/4"

14" 11 1/4" 2 7/16" 2 13/16" 1" 16"

16" 12 3/4" 2 13/16" 3 3/8" 1 1/8" 18 1/8"

18" 14 1/2" 3 1/8" 3 11/16" 1 1/4" 20 1/2"

20" 16" 3 1/2" 4 1/16" 1 7/16" 22 5/8"

22" 18" 3 3/4" 4 3/8" 1 9/16" 25 1/4"

24" 19 1/2" 4 1/4" 4 7/8" 1 3/4" 27 1/8"

26" 20 1/2" 4 9/16" 5 5/16" 1 7/8" 29"

28" 22 1/2" 4 7/8" 5 3/4" 2" 31 3/4"

30" 24" 5 1/4" 6 1/8" 2 1/8" 34"

32" 26" 5 5/8" 6 9/16" 2 1/4" 36 3/4"

34" 27 1/4" 5 7/8" 6 7/8" 2 3/8" 38 3/4"

36" 29" 8 1/4" 7 3/8" 2 1/2" 41"

Shaft Shaft Base Square Square CapBottom Top Plinth Plinth Mold Cap Cap Round Neck BeadDiameter Diameter Width Height Height Width Height Height Height Height

A B C D E F G H J K

8" 6 1/2" 10 3/4" 1 7/8" 2 3/8" 9 3/8" 1 3/8" 1" 1 5/8" 1"

10" 8 1/2" 13 3/8" 2 3/8" 2 7/8" 12 1/8" 1 3/4" 1 1/4" 2 1/16" 1 1/4"

12" 10" 16 1/8" 2 3/4" 3 1/4" 14 3/8" 2" 1 3/8" 2 1/2" 1 3/8"

14" 12" 18 3/4" 3 3/8" 4" 17 1/8" 2 3/8" 1 5/8" 2 7/8" 1 1/2"

16" 13 1/2" 21 1/2" 3 7/8" 4 1/2" 19 1/4" 2 3/4" 1 7/8" 3 3/8" 2"

18" 15" 24 1/4" 4 1/4" 5 3/8" 21 1/2" 3" 2 1/8" 3 3/4" 2 1/8"

20" 17" 27" 4 3/4" 6" 24 1/4" 3 3/8" 2 1/4" 4 1/8" 2 1/4"

22" 18 1/2" 29 3/4" 5 1/4" 6 7/8" 26 1/2" 3 3/4" 2 1/2" 4 1/2" 2 1/2"

24" 20" 32 1/2" 5 3/4" 7 1/2" 28 3/4" 4 1/8" 2 3/4" 5" 2 5/8"

26" 22" 35" 6 1/4" 8 3/8" 31 1/2" 4 3/8" 3" 5 3/8" 2 7/8"

28" 23 1/2" 38" 6 3/4" 8 3/4" 33 3/8" 4 3/4" 3 1/4" 5 7/8" 3"

30" 25" 40 1/2" 7 1/4" 9 1/4" 35 3/4" 5 1/8" 3 1/2" 6 1/4" 3 1/2"

32" 27" 43 3/8" 7 3/4" 10" 37 5/8" 5 1/2" 3 3/4" 6 5/8" 3 5/8"

34" 28 1/2" 46" 8 1/4" 10 7/8" 41" 5 3/4" 3 7/8" 7 1/8" 3 3/4"

36" 30" 48 3/4" 8 3/4" 11 3/8" 42 3/4" 6 1/4" 4 1/4" 7 1/2" 4"

8" 6 1/2" 10 3/4" 1 7/8" 2 3/8" 9 3/8" 1 3/8" 1" 1 5/8" 1"

12" 10" 16 1/8" 2 3/4" 3 1/4" 14 3/8" 2" 1 3/8" 2 1/2" 1 3/8"

16" 13 1/2" 21 1/2" 3 7/8" 4 1/2" 19 1/4" 2 3/4" 1 7/8" 3 3/8" 2"

20" 17" 27" 4 3/4" 6" 24 1/4" 3 3/8" 2 1/4" 4 1/8" 2 1/4"

24" 20" 32 1/2" 5 3/4" 7 1/2" 28 3/4" 4 1/8" 2 3/4" 5" 2 5/8"

28" 23 1/2" 38" 6 3/4" 8 3/4" 33 3/8" 4 3/4" 3 1/4" 5 7/8" 3"

32" 27" 43 3/8" 7 3/4" 10" 37 5/8" 5 1/2" 3 3/4" 6 5/8" 3 5/8"

36" 30" 48 3/4" 8 3/4" 11 3/8" 42 3/4" 6 1/4" 4 1/4" 7 1/2" 4"

8" 6 1/2" 1 3/8" 1 5/8" 1/2" 9 1/4"

12" 9 3/4" 2 1/8" 2 9/16" 3/4" 13 3/4"

16" 12 3/4" 2 13/16" 3 3/8" 1 1/8" 18 1/8"

20" 16" 3 1/2" 4 1/16" 1 7/16" 22 5/8"

24" 19 1/2" 4 1/4" 4 7/8" 1 3/4" 27 1/8"

28" 22 1/2" 4 7/8" 5 3/4" 2" 31 3/4"

32" 26" 5 5/8" 6 9/16" 2 1/4" 36 3/4"

36" 29" 8 1/4" 7 3/8" 2 1/2" 41"

Page 20: Crown Columns

Page Twenty

Architectural Column Collection

Design 400P(Plain)400F(Fluted)

Cap: ROMAN DORICBase: ATTIC

Shaft Shaft Base Square Square CapBottom Top Plinth Plinth Mold Cap Cap Round Neck BeadDiameter Diameter Width Height Height Width Height Height Height Height

A B C D E F G H J K

8" 6 1/2" 10 3/4" 1 7/8" 2 3/8" 9 3/4" 1 1/2" 1 1/8" 1 5/8" 1"

10" 8 1/2" 13 3/8" 2 3/8" 3" 12 1/2" 1 3/4" 1 3/8" 2 1/16" 1 1/4"

12" 10" 16 1/8" 2 3/4" 3 7/16" 14 3/4" 2 3/8" 1 5/8" 2 1/2" 1 3/8"

14" 12" 18 3/4" 3 3/8" 4" 17 1/2" 2 3/4" 2" 2 7/8" 1 1/2"

16" 13 1/2" 21 1/2" 3 7/8" 4 7/8" 19 7/8" 3 1/8" 2 1/4" 3 3/8" 2"

18" 15" 24 1/4" 4 1/4" 5 5/8" 22 1/4" 3 1/2" 2 1/2" 3 3/4" 2 1/8"

20" 17" 27" 4 3/4" 6 1/4" 25" 4" 2 3/4" 4 1/8" 2 1/4"

22" 18 1/2" 29 3/4" 5 1/4" 6 3/4" 27 3/8" 4 3/8" 3" 4 1/2" 2 1/2"

24" 20" 32 1/2" 5 3/4" 7 1/2" 29 3/4" 4 1/2" 3 1/4" 5" 2 5/8"

26" 22" 35" 6 1/4" 8 1/8" 32 1/2" 5 1/8" 3 1/2" 5 3/8" 2 7/8"

28" 23 1/2" 38" 6 3/4" 8 5/8" 34 5/8" 5 1/2" 3 7/8" 5 7/8" 3"

30" 25" 40 1/2" 7 1/4" 9 3/8" 37" 5 7/8" 4 1/8" 6 1/4" 3 1/2"

32" 27" 43 3/8" 7 3/4" 10" 39 1/4" 6 1/4" 4 1/4" 6 5/8" 3 5/8"

34" 28 1/2" 46" 8 1/4" 10 3/4" 42 1/8" 6 5/8" 4 5/8" 7 1/8" 3 3/4"

36" 30" 48 3/4" 8 3/4" 11 1/4" 44 1/8" 7" 5" 7 1/2" 4"

Shaft Shaft Base Square Square RoundBottom Top Plinth Plinth Mold Cap Cap Cap Neck BeadDiameter Diameter Width Height Height Width Height Height Height Height

A B C D E F G H J K

8" 6 1/2" 10 3/4" 1 7/8" 3 1/4" 9 3/4" 1 1/2" 1 1/8" 1 5/8" 1"

10" 8 1/2" 13 3/8" 2 3/8" 3 7/8" 12 1/2" 1 3/4" 1 3/8" 2 1/16" 1 1/4"

12" 10" 16 1/8" 2 3/4" 4 1/2" 14 3/4" 2 3/8" 1 5/8" 2 1/2" 1 3/8"

14" 12" 18 3/4" 3 3/8" 5 3/8" 17 1/2" 2 3/4" 2" 2 7/8" 1 1/2"

16" 13 1/2" 21 1/2" 3 7/8" 6 1/4" 19 7/8" 3 1/8" 2 1/4" 3 3/8" 2"

18" 15" 24 1/4" 4 1/4" 7 1/8" 22 1/4" 3 1/2" 2 1/2" 3 3/4" 2 1/8"

20" 17" 27" 4 3/4" 8 1/8" 25" 4" 2 3/4" 4 1/8" 2 1/4"

22" 18 1/2" 29 3/4" 5 1/4" 9" 27 3/8" 4 3/8" 3" 4 1/2" 2 1/2"

24" 20" 32 1/2" 5 3/4" 9 15/16" 29 3/4" 4 1/2" 3 1/4" 5" 2 5/8"

26" 22" 35" 6 1/4" 10 5/8" 32 1/2" 5 1/8" 3 1/2" 5 3/8" 2 7/8"

28" 23 1/2" 38" 6 3/4" 11 3/8" 34 5/8" 5 1/2" 3 7/8" 5 7/8" 3"

30" 25" 40 1/2" 7 1/4" 12" 37" 5 7/8" 4 1/8" 6 1/4" 3 1/2"

32" 27" 43 3/8" 7 3/4" 13 1/8" 39 1/4" 6 1/4" 4 1/4" 6 5/8" 3 5/8"

34" 28 1/2" 46" 8 1/4" 14" 42 1/8" 6 5/8" 4 5/8" 7 1/8" 3 3/4"

36" 30" 48 3/4" 8 3/4" 14 3/4" 44 1/8" 7" 5" 7 1/2" 4"

8" 6 1/2" 10 3/4" 1 7/8" 2 3/8" 9 3/4" 1 1/2" 1 1/8" 1 5/8" 1"

12" 10" 16 1/8" 2 3/4" 3 7/16" 14 3/4" 2 3/8" 1 5/8" 2 1/2" 1 3/8"

16" 13 1/2" 21 1/2" 3 7/8" 4 7/8" 19 7/8" 3 1/8" 2 1/4" 3 3/8" 2"

20" 17" 27" 4 3/4" 6 1/4" 25" 4" 2 3/4" 4 1/8" 2 1/4"

24" 20" 32 1/2" 5 3/4" 7 1/2" 29 3/4" 4 1/2" 3 1/4" 5" 2 5/8"

28" 23 1/2" 38" 6 3/4" 8 5/8" 34 5/8" 5 1/2" 3 7/8" 5 7/8" 3"

32" 27" 43 3/8" 7 3/4" 10" 39 1/4" 6 1/4" 4 1/4" 6 5/8" 3 5/8"

8" 6 1/2" 10 3/4" 1 7/8" 3 1/4" 9 3/4" 1 1/2" 1 1/8" 1 5/8" 1"

12" 10" 16 1/8" 2 3/4" 4 1/2" 14 3/4" 2 3/8" 1 5/8" 2 1/2" 1 3/8"

16" 13 1/2" 21 1/2" 3 7/8" 6 1/4" 19 7/8" 3 1/8" 2 1/4" 3 3/8" 2"

20" 17" 27" 4 3/4" 8 1/8" 25" 4" 2 3/4" 4 1/8" 2 1/4"

24" 20" 32 1/2" 5 3/4" 9 15/16" 29 3/4" 4 1/2" 3 1/4" 5" 2 5/8"

28" 23 1/2" 38" 6 3/4" 11 3/8" 34 5/8" 5 1/2" 3 7/8" 5 7/8" 3"

32" 27" 43 3/8" 7 3/4" 13 1/8" 39 1/4" 6 1/4" 4 1/4" 6 5/8" 3 5/8"

36" 30" 48 3/4" 8 3/4" 14 3/4" 44 1/8" 7" 5" 7 1/2" 4"

36" 30" 48 3/4" 8 3/4" 11 1/4" 44 1/8" 7" 5" 7 1/2" 4"

Design 300P(Plain)300F(Fluted)

Cap: ROMAN DORICBase: ROMAN DORIC

Page 21: Crown Columns

Page Twenty-one

Architectural Column Collection -- Decorative Capitals

EMPIRE WITH NECKING

GREEK ERECTHEUM WITH NECKING TEMPLE OF WINDS

ROMAN CORINTHIAN

MODERN COMPOSITE

GREEK ANGULAR IONIC WITH NECKING

To beUsed CapitalWith Diameter Height Abacus

6" 5" 3 1/8" 9"

8" 6 1/2" 7 3/4" 10"

10" 8 1/2" 5 1/4" 13 1/2"

12" 10 1/4" 6 1/4" 18"

14" 12 1/2" 7 1/4" 20 1/2"

16" 14" 8 3/4" 23"

18" 14" 8 3/4" 23"

20" 16 1/2" 10" 32"

22" 18" 11 1/4" 34"

24" 20 1/2" 12 3/4" 35 1/2"

To beUsed CapitalWith Diameter Height Abacus

6" 5" 6 7/8" 9"

8" 6 1/2" 7 3/4" 10"

10" 8 1/2" 10 1/4" 13 1/2"

12" 10 1/4" 11" 18"

14" 12 1/2" 14 1/2" 20 1/2"

16" 14" 17" 23"

18" 14" 17" 23"

20" 16 1/2" 18 1/4" 32"

22" 18" 17 1/4" 34"

24" 20 1/2" 19" 35 1/2"

To beUsed CapitalWith Diameter Height Abacus

6" 4 3/4" 7" 7 1/2"

8" 6" 8 1/4" 10 5/8"

10" 8 " 10 1/2" 16"

12" 9" 12" 18"

14" 12" 17" 19 3/4"

16" 13" 17 5/8" 26"

18" 15 1/2" 20" 29"

To beUsed CapitalWith Diameter Height Abacus

6" 5" 3 1/8" 6 7/8"

8" 7" 4 1/2" 9 3/8"

10" 9 1/8" 5 5/8" 13 1/8"

12" 11" 6 1/2" 14 1/4"

14" 12 3/4" 7" 16 1/4"

16" 15 1/4" 10 1/4" 22"

18" 16 1/2" 10" 21 1/4"

20" 18" 11 1/8" 26 1/4"

22" 20" 11 1/2" 27"

24" 22" 13 1/8" 31"

26" 24" 14" 31 1/2"

28" 25" 15" 32 1/2"

To beUsed CapitalWith Diameter Height Abacus

6" 4 7/8" 4 1/2" 6 1/2"

8" 6 1/2" 5 3/4" 7 1/2"

10" 8 3/8" 7 3/4" 10 1/2"

12" 10" 9 1/2" 14 1/4"

14" 12 3/4" 11 3/8" 16 1/4"

16" 14 1/2" 13 1/4" 18"

18" 15 1/2" 14 7/8" 21 1/2"

20" 16 1/2" 15 1/8" 21 1/4"

22" 18" 17" 26 1/4"

24" 20" 17 1/2" 27"

26" 24" 22" 31 1/2"

28" 25" 24" 32 1/2"

To beUsed CapitalWith Diameter Height Abacus

6” 5" 6 7/8" 7 3/4"

8” 6 1/2" 7 1/4" 10 1/4"

10" 8" 10" 13 5/8"

12" 9 1/2" 11 1/4" 16 1/4"

14" 12 " 14" 21 1/4"

16" 13 1/4" 15 1/8" 22 1/2"

18" 15 1/2" 18 1/4" 26"

20" 17 1/2" 21 1/2" 28"

22" 18" 21 1/2" 27 3/4"

24" 19 1/2" 23" 35 3/4"

26" 22" 24" 37 1/4"

28" 24" 26 1/8" 37 1/4"

30" 26" 30" 39"

To beUsed CapitalWith Diameter Height Abacus

6" 4 1/2" 2 3/4" 7 1/2"

8" 6 5/8" 4" 9 1/4"

10" 8 1/2" 5 1/2" 14 1/2"

12" 10 1/2" 6 1/8" 17 1/4"

14" 12 1/2" 7 1/4" 20 1/2"

16" 14 3/4" 8 3/8" 22 1/2"

18" 16" 9 3/4" 24 1/4"

20" 18" 11" 29 3/4"

22" 20 5/8" 12 3/4" 35"

24" N/A N/A N/A

26" 24" 14 3/4" 39 1/2"

To beUsed CapitalWith Diameter Height Abacus

6" 4 1/2" 5 1/2" 7 1/2"

8" 6 5/8" 8" 9 1/4"

10" 8 1/2" 10 1/8" 14 1/2"

12" 10 1/2" 11" 17 1/4"

14" 12 1/2" 14 3/8" 20 1/2"

18" 14 3/4" 17" 22 1/2"

20" 18" 19" 30"

To beUsed CapitalWith Diameter Height Abacus

6" 4 3/4" 7" 9 3/8"

8" 6" 8" 11 1/2"

10" 8 3/8" 11" 14"

12" 9 1/2" 13 3/4" 19"

14" 12 1/2" 17 1/4" 22 3/4"

16" 13" 17 3/8" 27"

18" 15" 17 3/4" 25 1/4"

20" 17 1/4" 25 1/4" 39"

22" 18" 25 1/2" 39"

24" 20" 28 1/2" 42"

26" 22 1/2" 32" 42"

28" 23 3/4" 32" 44"

30" 25" 34 1/2" 46"

32" 26" 36" 48"

36" 32" 42" 55"

Page 22: Crown Columns

Architectural Column Collection -- Decorative Capitals

ROMAN IONIC SCAMOZZI

Crown Column & Millwork offers an infinite selection of specialty items, including these hand carved capitals. We specialize in historical replications, custom specifications andunique designs. For more information regarding a custom itemplease contact our sales department at 888-862-0880.

S P E C I A L T Y I T E M S

To ensure a maximum product life and successful installation, follow these tips for care, handling and installation:

1. Always keep wood products in a dry, well-ventilated area until you are ready to begin painting.

2. Exterior applications require only the best exterior grade oil-based paint. Apply at least one coat prior to installation toseal the wood against moisture. Then, apply your finish coats once your columns have been erected.

3. Always provide for sufficient ventilation. Proper airflow is one of the keys to a successful installation. Moisture-related problemsmay be avoided by using a recessed soffit (see drawing) and providingequal amounts of air flow at both the top and bottom of the shaft.

4. Maintain your columns regularly. Check for ventilation, bird’s nests, insects, etc., and touch up the oil-based paint on all exposed surfaces. Repaint as necessary.

When properly installed and maintained, architectural wooden columns will make a significant and long-lasting addition to your project.

Page Twenty-two

Cap

C A R E & H A N D L I N G

To beUsed CapitalWith Diameter Height Abacus

6" 5 1/8" 2 3/8" 6 1/8"

8" 6 5/8" 3 3/8" 8 1/4"

10" 9" 4 1/2" 11 1/2"

12" 11 1/4" 4 3/4" 13"

14" 13 1/4" 5 3/4" 17"

16" 15" 6 3/8" 18"

18" 16" 6 1/2" 21 1/4"

20" 18 1/2" 9" 25"

22" 20 1/2" 9 1/2" 25 1/8"

24" 22 3/4" 9 1/2" 26 1/2"

To beUsed CapitalWith Diameter Height Abacus

6" 5 1/4" 2 1/2" 7 7/8"

8" 7" 3 3/8" 11"

10" 9" 4" 14"

12" 11" 5" 16 3/4"

14" 11" 5 1/8" 16 1/2"

16" 14 1/4" 5 7/8" 21 3/4"

18" 16" 7 1/2" 24 3/4"

20" 18" 8 1/2" 28 1/2"

22" 20" 9 1/4" 30 1/2"

24" 22" 10 5/8" 32 1/4"

Page 23: Crown Columns

Page Twenty-three

Ordering & Quotation Information

Q U O T A T I O N & O R D E R I N G

I N F O R M A T I O N

Contact our sales department for a custom quotation and our current lead time. Your requests can be processed mostquickly if you have the following information:

1. Column design number if applicable2. The plan type3. Quantity4. Species of lumber (paint-grade or stain-grade)5. Plain or fluted?6. Is the column for interior or exterior application?7. Style of capital and base molding8. Bottom diameter of the shaft9. Overall length (floor to ceiling height)10. Will the column be used as a single shaft or split to

surround a structural support? If the column is to be used around a structural support, please supply the size and shape of the support element.

11. Will the column match an existing column? If yes, providing photos, drawings and dimensions will expedite your quotation.

h

P L A N T Y P E S

a b c d

ef g h

ij q

s

Page 24: Crown Columns

Crown Column & Millwork Co., L.L.C. - P. O. Box 2219 - Gadsden, AL 35903p.1-888-862-0880 p.256-494-0880 f.256-494-0898 07/03

An elegant...

distinctive accent

An elegant...

distinctive accent