Craftsman Front Scoop

Owner's Manual

I:RI:IFT. MRN®Model No. 486.24847

FRONT SCOOP TRACTOR ATTACHMENT

CAUTION:

Before using this product, read thismanual and follow all Safety Rulesand Operating Instructions.

IMPORTANT - READ THIS FIRST???For Missing Parts or Assembly QuestionsPlease Call 866-576-8388

Mon.-Fri. 7 a.m.-5 p.m. CST.

FAX 217-728-2032 or e-mail [email protected] parts will be sent UPS in 24 hours directly to your home.

• Safety• Assembly• Operation• Maintenance• Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.www.sears.com/craftsma n

PRINTED IN U.S.A. FORM NO. 49326 (1/05)

WARRANTY .............................................................. 2SAFETY RULES ........................................................ 3FULL SIZE HARDWARE CHART ............................. 4CARTON CONTENTS .............................................. 6ASSEMBLY ............................................................... 7OPERATION ............................................................ 14

MAINTENANCE ...................................................... 15TROUBLESHOOTING ............................................ 15REPAIR PARTS ILLUSTRATION .......................... 16REPAIR PARTS LIST ............................................. 17SLOPE GUIDE ........................................................ 19PARTS ORDERING/SERVICE ................. Back Page

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN FRONT SCOOP TRACTOR ATTACHMENT

For one year from the date of purchase, when this scoop is maintained and lubricated according to the operating andmaintenance instructions in this owner's manual, Sears will repair any defect in material or workmanship free ofcharge. If this scoop is used for commercial or rental purposes, this warranty applies for only 90 days from the date ofpurchase.

This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure tomaintain the equipment according to instructions contained in this owner's manual.

WARRANTY SERVtCE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES.

This warranty applies only while this product is in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817 WA., Hoffman Estates, Chicago, IL 60179

The model number and serial number will be found on adecal attached to the bucket.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.24847

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.Exercisecautionatalltimes,whenusingpowerequipment.

• Read this owner'smanualbefore attemptingtoassembleoroperatethescoopattachment.

• Readthevehicleowner'smanualandknowhowtooperate your vehicle before using the scoopattachment.

• Nevercarrypassengersin thescoopbucket.It hasnotbeendesignedto carrypassengers.

• Neverallowchildrento operatethe vehicleor thescoopattachment.

• Donotallowadultsto operatethevehicleor scoopattachmentwithoutproperinstructions.

• Alwaysbeginwiththetransmissioninfirst (low)andgraduallyincreasespeedasconditionspermit.

• Drivethetractorat reducedspeedoverroughterrainandhillsidesor nearcreeksandditchesto preventtippingoverandlossofcontrol.Donotdrivetooclosetoa creekorditch.

• Neverramthescoopintomaterialat highspeed.• Vehiclebrakingandstabilitymaybeaffectedwiththe

attachmentof this scoop.Donot fill the scooptomaximumweight capacitywithout checkingthecapabilityofthevehicleto safelydriveandstopwiththescoopattached.

• Beforeoperatingvehicleonanygrade(hill)refertothe safety rules in the vehicle owner's manualconcerningsafeoperationon slopes.Referalsototheslopeguideonpage19of thismanual.Stayoffsteep slopes!

• Follow maintenance and lubrication instructions asoutlined in this manual.

Look for this symbol to point out important safety precautions. It means--Attention!!Become alert!! Your safety is involved.

These accessories were available when the unit was purchased. They are also available at most Sears retail outlets andservice centers. Most Sears stores can order repair parts for you when you provide the model numbers of your tractor andscoop.

WHEEL WEIGHT

/

/

/

L/

M

N/

o

BJJ/

/

/

/

/

/

/

/

/

R/

sJ

D i FJ

G

CC

DD

!

/ FF

GG

/

/

HH

/

BB

PARTS NOT SHOWN FULL SIZE

JJ

KK

LL

PARTS BAG CONTENTS

Not all parts will be needed for fit-up to any one tractor.

Discard uneeded parts after assembly is finished.

REF. QTY.

A 2

B 2

C 3

D 2

E 4

F 5

G 5

H 3

t 2

J 2

K 1

L 2

M 2

N 3

O 2

P 2

Q 12

R 5

S 1

T 1

DESCRIPTION REF.

Hex Bolt, 5/8" x 1-1/2" U

Hex Bolt, 1/2" x 1-1/2" V

Hex Bolt, 1/2" x 1" W

Hex Bolt, 3/8" x 1-1/4" X

Hex Bolt, 3/8" x 1" Y

Hex Bolt, 5/16" x 1" Z

Hex Bolt, 5/16" x 1-3/4" AA

Hex Bolt, 1/4" x 1-3/4" BB

Carriage Bolt, 5/16-18 x 1" CC

Carriage Bolt, 1/4-20 x 3/4" DD

Slotted Truss Head Bolt, 10-32 x 5/8" EE

QTY. DESCRIPTION

6 Lock Washer, 3/8"

3 Washer, 1/4"

8 Washer, 5/16"

3 Washer, 1/2" Small

6 Washer, 5/8"

2 Washer, 1/2" Large

2 Washer, 3/4"

2 Washer, 1"

3 Hairpin Cotter, Long

4 Hairpin Cotter, Short

6 Cotter Pin, 1/8" x 1-1/4"

Nylock Nut, 5/8" FFF

Nylock Nut, 1/2" GG

Nylock Jam Nut, 1/2" HH

Hex Nut, 3/8" tt

Nylock Nut, 3/8" JJ

Nylock Nut, 5/16" KK

Nylock Nut, 1/4" LL

Hex Nut, 1/4" MM

Nylock Nut, #10-32

2 Cotter Pin, 1/8" x 1-1/2"

4 Spacer, 1/2"

1 Spacer, 3/8" Small

2 Clevis Pin

1 Compression Spring

6 Cable Tie

2 Tilt Stop Bracket

1 Hose Clip

CARTON CONTENTS

1. Bucket Assembly

2. Pin Stop Bracket

3. Lift Frame Assembly

4. Lift Bracket Assembly

5. Tilt Anchor Assembly

6. Right (LT) Side Plate

7. Left (LT) Side Plate

8. Right (GT) Side Plate

9. Left (GT) Side Plate

10. Dump Control Rod

11. Lift Strap Assembly (2)

12. Tilt Bracket Assembly

13. Attachment Rod

14. Dump Handle Tube

15. Lift Handle Tube

16. Dump Handle Tube Extension

17. Dump Pivot Bracket

18. Lift Handle Tube Extension

19. Dump Control Pin

20. Lift Cable (Short)

21. Lift Cable (Long)

2

6 8

17

%11

11 - j12 %

TOOLS REQUIRED FOR ASSEMBLY

(1)(1)(2)(2)(2)(2)(2)(1)

#2 Phillips ScrewdriverStandard Screwdriver15/16" Wrenches (one should be box-end)3/4" Wrenches9/16" Wrenches7/16" Wrenches1/2" Wrenches3/8" Wrench

ADDITIONAL ITEMS NEEDEDRuler or Tape MeasureGrease

STEP 1 - REMOVE PARTS FROM CARTON

• Remove the hardware pack and all loose parts fromthe carton.

• Lay cardboard on floor to help prevent scratching ofpainted parts.

• Lay out and identify all the parts and hardware asshown on pages 4 through 6.

5/16" WASHERS

______------5/16" x 1"HEX BOLTIIL PIN STOP

./BRACKET

i BUCKET

ASSEMBLY

/

5/16"NYLOCK NUT

3/8" NYLOCK NUT

FIGURE 1

3/8" x 1o1/4"HEX BOLT

3/8" HEX NUT

STEP 2 - INSTALL TWO BOLTS

• Assemble two 3/8" x 1-1/4" hex bolts and 3/8" hex

nuts, threading the nut all the way onto the bolt until itis tight against the head of the bolt. See figure 1.

• Install a nut/bolt assembly into the bucket assemblyand fasten using a 3/8" nylock nut. Tighten. Repeatfor the other side. See figure 1.

STEP 3 - INSTALL PIN STOP BRACKET

Install the pin stop bracket to the top of the bucketassembly using four 5/16" x 1" hex bolts, eight 5/16"washers and four 5/16" nylock nuts. Center the boltsin the slots of the pin stop bracket and the slots of thebucket. Tighten the bracket so that it is square withthe bucket. See figure 1.

STEP 4 - INSTALL LIFT FRAME ASSEMBLY

• Apply grease to the mounting surface of the bucketassembly and the inside of the lift frame arms.See figure 2.

Assemble the lift frame assembly to the bucketassembly using two 5/8 x 1-1/2" hex bolts and 5/8"nylock nuts. Tighten, then loosen the nuts 1/4 turn,or until the lift frame pivots freely. See figure 2.

5/8" x 1-1/2"HEX BOLT

\APPLY

GREASE j _-

APPLY LIFT FRAMEGREASE ASSEMBLY

5/8" NYLOCK NUTS

FIGURE 2

APPLY GREASE

STEP 5-INSTALL LIFT BRACKET ASSEMBLY

• Assemble the lift bracket assembly to the lift frameassembly using two 5/8" washers and 1/8" x 1-1/4"cotter pins. See figure 3.

LIFT FRAMEASSEMBLY

FIGURE 3

STEP 6 - INSTALL TILT ANCHOR ASSEMBLY

• Assemble the tilt anchor assembly to the lift bracketassembly using two 1/2" x 1" hex bolts and nylockjam nuts. Tighten. See figure 4.

1/2" NYLOCKJAM NUTS

TILT ANCHORASSEMBLY

1/2" x 1"HEX BOLT

LIFTBRACKET

I

1/2" x 1"HEX BOLT

STEP 7 - INSTALL LIFT STRAP ASSEMBLIES

• Loosen the bolts and nuts on the lift strapassemblies 1/4 turn or until the straps will slide backand forth. You will retighten them later in step 24.

Turn the lift strap assemblies as shown. Install eachlift strap assembly to an arm of the lift bracketassembly and then secure with a small 1/2" washerand a short hairpin cotter. See figure 5.

Position the lower end of each lift strap assembly tothe outside of the lift frame. Fasten to the upper frontholes in the lift frame using a 1/2" x 1" clevis pin, 1/2"spacer and short hairpin cotter for each assembly.See figure 5.

NOTE: The lift strap assemblies may be installed in therear mounting holes of the lift frame to increasethe lift height, but this will also increase the liftingeffort. The front holes give a lift height of about 6-1/2" and require 28 Ibs. of force to lift a 150 Ibload. The rear holes will give a lift height of about8-1/2" and require 35 Ibs. of force.

SHORT HAIRPINCOTTER

/ 1/2" WASHER

_.@../ (SMALL)/

LIFT STRAPSHORT ASSEMBLYHAIRPIN / _

\%COTTER1/2"SPACER

UPPER FRONT 1/2"x 1"MOUNTING HOLE CLEVIS PIN

FIGURE 5 Bucket removed for clarity.

FIGURE 4

STEP 8 - INSTALL TILT BRACKET ASSEMBLY

NOTE: If you mounted the lift strap assemblies in Step 7to the rear holes in the lift frame for increasedlifting height, you need to replace the 3/8" spaceron the tilt bracket assembly with the smaller 3/8"spacer from the parts bag at this time.

Loosen the bolts and nuts on the tilt bracketassembly 1/4 turn or until the two plates will slideback and forth. You will retighten them later in step23. See figure 6.

Lightly apply grease to the end of the arm on the tiltanchor assembly and install the tilt bracket assemblyto the arm using a 1/2" x 1" hex bolt and 1/2" nylockjam nut. Tighten. Loosen the nut 1/4 turn, or until thetilt bracket assembly pivots freely. See figure 6.

Install a 1/4" x 1-3/4" hex bolt through a 1/4" washerand then through the end of the extension spring onthe tilt bracket assembly. Next, install a 1/4" hex nutall the way onto the threads of the bolt. Finally installthe end of the bolt into the hole in the arm of the tiltanchor assembly and secure using a 1/4" nylock nut.Tighten. See figure 6.

STEP 9 - INSTALL DUMP PIVOT BRACKET

Install a 1/8" x 1-1/2" cotter pin to the inside hole inthe shaft shown in figure 9, and then install a 1"washer onto the shaft. Apply grease to the end of theshaft and install the dump pivot bracket assemblyonto the shaft. Install a 1" washer onto the shaft andsecure it using a 1/8" x 1-1/2" cotter pin. See figure 7.

1/8" x 1-1/2"COTTER PIN

_'_ 1" WASHERSJ

APPLYGREASE


DUMP PIVOTBRACKET

FIGURE 7

1/4" NYLOCK NUT

TILT ANCHOR

ASSEMBLY_

1/4" HEX NUT

1/2" x 1"HEX BOLT

1/4" WASHER

J

I APPLY1/4"x 1-3/4" GREASEHEX BOLT 1/2" NYLOCK

JAM NUTTILT BRACKETASSEMBLY

FIGURE 6

STEP 10 - INSTALL DUMP CONTROL ROD

Install a 1/8" x 1-1/4" cotter pin into the inside hole ineach end of the dump control rod. Spread the ends ofthe cotter pins and wrap around the rod. Install a 5/8"washer onto each end of the control rod. See figure 8.

Install the dump control rod to the dump pivot bracketand bucket. Fasten using two 5/8" washers and 1/8" x1-1/4" cotter pins. Spread the ends of the cotter pinsand wrap around the rod. See figure 8.


5/8" WASHERS

1-1/4"COTTERPINS


5/8" WASHERS

DUMPCONTROLROD

FIGURE 8

STEP 11 - INSTALL TILT STOP BRACKETS

Install a tilt stop bracket to each side of the bucketusing a 1/4" x 3/4" carriage bolt, 1/4" washer and 1/4"nylock nut. Do not tighten the nuts until step 25. Seefigure 9.

STEP 13 - INSTALL LIFT HANDLE TUBEEXTENSION

• Install the lift handle tube extension on the lift handletube using a 1/4" x 1-3/4" hex bolt and 1/4" nylocknut. See figure 11.

TmLT STOP

8RACKET

1/4" NYLOCK _.

NUT 1/4" x 3/4"J1/4" WASHER CARRIAGE BOLT

FIGURE 9

FIGURE 11

LIFT HANDLETUBE EXTENSION

l,;'x;'O3'LZ'" \

1/4" NYLOCK NUT

LIFT HANDLETUBE

STEP 12 - INSTALL LIFT HANDLE TUBE

• Install the lift handle tube on the index bracket usingtwo 5/16" x 1-3/4" hex bolts and 5/16" nylock nuts.See figure 10.

LIFT HANDLETUBE

5/16"

NYLOCK 5/16" x 1-3/4"

-_®_ HEX BOLT

INDEX

FIGURE 10

STEP 14 - INSTALL LIFT CABLE

Squeeze the lift trigger and slide the anchor end of thelift (short) cable into the hole in the trigger. Releasethe trigger and guide the cable through the slot in thebottom of the trigger and trigger housing. Insert theend of the plastic cable covering into the triggerhousing. See figure 12.

Connect the hooked end of the lift cable into the index

rod, and install the threaded cable adjuster into thenotch in the top of the index bracket, placing a nut oneach side of the notch. See figure 12.

Adjust the cable adjuster nuts so that when the triggeris squeezed, the bottom of the index rod raisesenough to release from the latched position. The indexrod should also lower far enough to lock in the latchedposition when the trigger is released. See figure 12.

• Attach the lift cable to the lift handle using three cableties.

10

LmFTTRIGGER

LIFT CABLE

CABLE o OSTMENT- CABLEANCHOR- HOOK ' (

INDEX RO_

FIGURE 12

STEP 16 - INSTALL DUMP HANDLE TUBEEXTENSION

• Install the dump handle tube extension on the dumphandle tube using a 1/4" x 1-3/4" hex bolt and 1/4"nylock nut. See figure 14.

DUMP HANDLETUBE EXTENSION

\

1/4"x 1-3/4"

REX BOLT

\

DUMP HANDLE

TUBE _/ 1/4" NYLOCK

NUT

FIGURE 14

STEP 15 - INSTALL DUMP HANDLE TUBE

• Install the dump handle tube to the dump pivot bracketassembly using three 5/16" x 1-3/4" hex bolts andnylock nuts. See figure 13.

DUMP /

HANDLETUBE

DUMP PIVOTBRACKET

\ 5/16"NYLOCKNUT/

5/16"

NUTS

5/16" x 1-3/4"HEX BOLTS

STEP 17 - INSTALL DUMP CABLE

Squeeze the dump trigger and slide the anchor end ofthe dump (long) cable wire into the hole in the trigger.Release the trigger and guide the cable wire throughthe slot in the bottom of the trigger and triggerhousing. Insert the end of the plastic cable coveringinto the trigger housing. See figure 15.

• Attach the dump cable to the dump handle tube usingthree cable ties.

DUMP CABLE

DUMP TRIGGER

FIGURE 15

FIGURE 13

11

STEP 18 - INSTALL DUMP CONTROL PIN STEP 19 - INSTALL HOSE CLIP AND SPACER

Install a small 1/2" washer and then the compressionspring onto the dump control pin. Install the dumpcontrol pin into the pin stop bracket. Make sure the flatside of the pin faces to the front when finished. Seefigure 16.

Connect the hooked end of the dump cable into thehole in the dump control pin. Install the threaded cableadjuster down into the notch in the pin stop bracket,placing a nut on each side of the notch. Adjust andtighten the adjuster nuts so that the tapered end of thedump control pin extends 3/4" through the side of thepin stop bracket. See figure 16.

DUMP CONTROL PIN

3/4"--,.-__

PIN STOPBRACKET

I

DUMP CONTROL PIN

PIN

BRACKET

Secure the dump cable to the back of the bucket usinga hose clip, #10 x 5/8" truss-head bolt and #10-32nylock nut. See figure 17.

Store the unused 3/8" spacer from step 7 on the liftframe using a 5/16" x 1" hex bolt and nylock nut. Seefigure 17.

3/8" SPACER

5/15"x1"REX BOLT_ /. I I 5/16"

I/ NYLOCK

IJl NUT

#10-32 NYLOCK NUT

/

FIGURE 17

#10 x 5/8"

HOSE TRUSSCLIP HEAD BOLT

STEP 20 - INSTALL (LT) SIDE PLATES

Install a large 1/2" washer and a 1/2" spacer onto a1/2" x 1-1/2" hex bolt. Install the bolt into the holeshown in the left (LT) side plate, and fasten using anylock nut. Repeat the step for the right side plate, butinstall the bolt, flat washer and spacer from theopposite direction. See figure 18.

FIGURE 16

1/2" NYLOCKNUT

LEFT (LT)SIDE PLATE

\

USE THIS HOLE //

1/2" SPACER

LARGE 1/2"WASHER

1/2" x 1-1/2"

"-.,_ _HEXBOLT.

FIGURE 18

12

Remove any bolts present in the mounting holes onthe left side of the tractor frame. Do not remove boltsfrom right side of frame until left side plate has beeninstalled. See figure 19.

Install the left (LT) side plate on the tractor with thespacer to the outside. Fasten to the tractor frameusing three 3/8" x 1" hex bolts and 3/8" lock washersand one 5/16" x 1" carriage bolt and 5/16" nylock nut.Tighten 3/8" bolts only until the are snug andIockwashers are flattened. Repeat for the right sideplate. See figure 19.

5/16" NYLOCK NUT

5/16_ x 1"CARRIAGE BOLT

(3) 3/8" LOCK 1"(3) 3/8" xWASHERS HEX BOLTS

FIGURE 19

LEFT (GT)SIDE PLATE

<_J _v _"

I/"

L/ -. " (2 316LOCKd_<_(_ _ _e _WASHERS

/ _ (2) 3/8" x 1"LONG HEX BOLTSHAIRPIN 3/4" WASHERCOTTER

FIGURE 20

STEP 22 - MOUNT SCOOP TO TRACTOR

Align the scoop with the side plates on the front of thetractor. Lift the rear of the scoop and slide the notchesin the scoop frame onto the bolts or pins in the tractorside plates. Stand on the left side of the tractor andpush down on the scoop dump handle until the holesin the scoop frame and the holes in the side plates arealigned. Install the attachment rod through the holesfrom the left side and secure it with a long hairpincotter. Se figure 21.

STEP 21 - INSTALL (GT) SIDE PLATES

Remove any bolts present in the mounting holes onthe left side of the tractor frame. Do not remove boltsfrom right side of frame until left side plate has beeninstalled. See figure 20.

Install the left (GT) side plate with the pin to theoutside using two 3/8" x 1" hex bolts and lockwashers. Tighten only until bolts are snug andIockwashers are flattened. Repeat for the right sideplate. See figure 20.

• Install a 3/4" washer and a long hairpin cotter to thepin in each side plate. Remove them while mountingthe scoop. See figure 20.

LONGHAIRPINCOTTER

/

FIGURE 21

DUMP HANDLE

BOLT OR PIN

ATTACHMENTROD

SCOOP _%

ASSEMBLY

13

STEP 23- ADJUST TILT BRACKETASSEMBLY

Lower the scoop assembly onto a smooth levelsurface. For normal use, let the bottom of the bucketrest flat on the ground. For more aggressive scrapingaction, place 1/4" shims under the rear of the bucketat each end.

Swing the tilt bracket forward to check for clearancewith the pin stop bracket. There should be a small gapbetween the tilt bracket and the side of the pin stopbracket. If not, adjust the position of the pin stopbracket side to side.

Make sure the two bolts in the tilt bracket are looseenough to turn by hand. Align the tilt bracket so thatthe dump control pin snaps into the hole in the tiltbracket. The tapered end of the pin should extendclear through the tilt bracket. Tighten the two boltsand nuts in the tilt bracket. See figure 22.

TIGHTEN , /TILT BRACKET

PIN STOP BRACKET

FIGURE 22

STEP 24 - ADJUST LIFT STRAPS

Make sure the nuts and bolts in the lift straps areloose enough to turn by hand. Stand on the right sideof the scoop and hold the lift handle as far forwardas it will go while you tighten one of the nuts in the liftstraps.You can let go of the lift handle to tighten theother three nuts in the lift straps. See figure 23.

LIFT STRAPTIGHTENASSEMBLIESNUTS

FIGURE 23

STEP 25 - ADJUST TILT STOP BRACKETS

Raise the scoop until it locks in the TRANSPORTposition. Push the tilt stop brackets on each side of thebucket down against the lift frame arms, and tightenthe nuts. See figure 24.

TILT STOPBRACKET

FIGURE 24

LIFT FRAME ARM

14

STEP 26 - CHECK DUMPING OPERATION

With the scoop in the transport position, squeeze thedump trigger and push down on the dump handle todump the bucket. Release the dump trigger and lift upon the handle to lock the bucket in the upright position.If the dump control pin passes underneath the tiltbracket instead of locking into it, move the pin stopbracket on top of the bucket farther towards the rear. Ifthis does not work, repeat steps 23, 24 and 25.

KNOW YOURFRONTENDSCOOP

Read this owner's manual and safety rules beforeoperating your front end scoop.

Compare the illustration below with your front end scoopto familiarize yourself with the various controls and theirlocations.

LIFTHANDLE

\DUMPHANDLE

LIFT /TRIGGER

/DUMPTRIGGERLEVER

DUMP TRIGGER LEVER Press to release the dump pin.DUMP HANDLE Press down to dump the bucket.LIFT TRIGGER LEVER Press to release the index pin.LIFT HANDLE Press down to lift the bucket assembly.

HOW TO USE YOUR SCOOP

DO NOT EXCEED 200 LB. CAPACITY OF BUCKET

One cubic foot of dirt weighs approximately 80 Ibs.

One cubic foot of dry sand or gravel weighs approximately100 Ibs.

&CAUTION: Vehicle braking and stabilitymay be affected with the addition of anaccessory or an attachment. Be aware ofchanging conditions on slopes.

Refer to the vehicle owner's manual for instructions onsafe operation on slopes.

Use the slope guide provided on page 23 of thismanual to determine whether slope angle is too steepfor safe operation.

Always test to make sure your vehicle hasadequate power and braking capabilities wheneverhauling a substantial amount of weight in your frontend scoop. Use extra caution when operating onslopes.

For best handling and traction, distribute the weightof the load evenly in the bucket.

& CAUTION: Never ram the scoop intomaterial at high speeds.

Keep the lift handle locked in the raised positionwhen tilting the scoop bucket forward to dump.

The lift handle must be locked in the raised positionto allow the dump handle to lock the scoop bucketback in the upright position after dumping.

Do not scrape or push material with the scoopbucket while it is tilted forward.

Add wheel weights for improved traction whenusing the scoop.

To dump material from the bucket, squeeze thedump trigger and push the dump tube handle down.Release the trigger before returning the bucket tothe upright position.

To lower the bucket, squeeze the lift trigger andthen lift up on the lift handle. If the trigger is hard todepress, you may need to push down on the lifthandle while squeezing, and then lift up. Releasethe trigger before retuning the bucket to the raisedposition.

Do not exceed mowing speed (3 mph) when thefront end scoop is attached to the tractor.

CAUTION: To avoid possible injury, beforedumping the bucket, make sure that no oneis near the bucket.

,_ CAUTION: Always lower the scoop bucketto the ground before leaving the tractor.

15

CUSTOMER RESPONSIBILITIES

• Read and follow the maintenance schedule and the maintenance procedures listed in this section.

MAINTENANCE SCHEDULE .._ _e/_e_/'_o_/'_,__o_"

Fill in dates as you ___J

complete regular service. ,_e__e_ 'y

Check for loose fasteners X

Cleaning XLubricate X

Service Dates

CHECK FORLOOSEFASTENERS

Before each use make a thorough visual check ofthe front end scoop for any bolts and nuts whichmay have loosened. Retighten any loose bolts andnuts.

CLEANING

• After each use, clean off any dirt and debris fromthe scoop bucket lift frame.

• Before storing at the end of each season, rinse offthe scoop bucket and scoop lift frame. Allow to drythoroughly. Paint any exposed metal surfaces toprotect from rust.

• Store in a clean, dry area.

LUBRICATION

• Lightly oil all pivot points on the scoop lift mechanism.• Lightly oil the surface on the scoop bucket where

the attachment lift frame pivots.• Apply a good grade of spray lubricant to the trigger

assemblies on the lift handle and dump handle.

PROBLEM

Scoop won't lock intoraised/transport postion.

Scoop bucket won't lock into levelposition.

Lift handle trigger won't releasescoop from the transport position.

Dump handle trigger won'trelease bucket to dump.

CAUSE

1. Index rod is jamming.

2. Frame is hitting the tilt stopbrackets.

1. Dump control pin is not aligned withthe tilt bracket.

1. Index rod is jamming.

2. Lift cable is not adjusted properly.

1. Dump control cable is not adjustedproperly.2. Latch mechanism is not adjustedproperly.

CORRECTION

1. Apply grease to the bottom slot in thelift bracket, where the index rod slides.2. Adjust the tilt stop brackets asinstructed on page 14.

1. Adjust tilt bracket and lift straps asinstructed on page 14.

1. Apply grease to the bottom slot in thelift bracket, where the index rod slides.2. Adjust cable nuts as instructed onpage 11.

1. Adjust parts as instructed for figure16 on page11.2. Adjust parts as instructed for figure22 on page 14.

Bucket is becoming more difficult 1. Debris is lodged between bucket 1. Remove all debris from between theto tilt up or down. assembly and lift frame, bucket assembly and lift frame.

16

NOTES

17

79\

77

REPAIR PARTS FOR MODEL 486.24847

69

11

//

_ 7851

6463

8

I 24I 73

rs /74 72 14

29

\[[I

/-

30

31 3!

28 [\\ [

13

!_ _ 27

/22 _

!33

/

48

-_ 631i70

61

59 \

//

//

//

62

1352

45

//

52

/43

19

//

42

81

13

36

/ 37

4

\l38

//

1o/

\39 \

\\

\

>

41

13

13 5152

45

//

5

/

54

18

REPAIR PARTS FOR MODEL 486.24847

REF. PARTNO. NO.

RER PARTQT_ DESCRIPTION NO. NO. QTY. DESCRIPTION

1 1509-692 726-0178

3 492654 49266

5 476746 47554

7 712-01278 47317

9 4755510 47189

11 4736912 47368

13 4781014 HA21362

15 4307016 25350

17 4306318 25343

19 741-019220 R1917616

21 4305522 43001

23 6375524 43178

25 6496426 48115

27 6367528 25510

29 4334330 43020

31 R1917241032 47364

33 712-308334 43003

35 712-026136 63568

37 6356938 49270

39 4706640 49271

41 4948342 43601

3 Hex Bolt, 1/4-20 x 1-3/4" (Grade 5)6 Cable Tie1 Lift Tube Handle Extension2 Oval Screw, 10-24 x 1-1/2"2 Plastic Plug, 1-1/4" O.D.Tube2 Trigger Housing Assembly2 Square Nut, #10-242 Grip, Black1 Cable, Lift5 Nylock Nut, 1/4"1 Roll Pin, 3/16" x 1-3/4"1 Roll Pin, 5/16" x 1-3/4"

14 Nylock Nut, 5/16-188 Nylock Nut, 3/8-166 Flat Washer, 3/8"4 Lift Strap8 Hex Bolt, 5/16-18 x 1" (Grade 5)1 Lift Bracket

2 Flange Bearing with Flats3 Flat Washer, 1/2" x 1" (Small)4 Hairpin Cotter, 3/32" x 1.8"10 Hex Bolt, 3/8-16 x 1" (Grade 5)2 Trigger Assembly1 Hex Nut, 1/4-201 Tilt Anchor Assembly3 Nylock Jam Nut, 1/2-131 Lift Arm Assembly2 Mounting Bracket3 Hairpin Cotter, 3/32" x 2-5/16"2 Hex Bolt, 1/2-13 x 1-1/2" (Grade 5)2 Flat Washer, 1/2" x 1-1/2" (Large)4 Spacer, 0.52" x 0.75" x 0.4"2 Nylock Nut, 1/2-136 Lock Washer, 3/8"2 Nylock Nut, 5/8-111 Right (GT) Side Plate1 Left (GT) Side Plate1 Dump Handle Tube Extension1 Attachment Rod1 Dump Handle Tube1 Dump Control Cable)3 Washer, 1.59" x 1.032" x 0.60"

43 4309344 710-0865

45 R1921201646 25362

47 6498348 HA6441

49 4157650 64963

51 4308452 43010

53 6496854 49273

55 4926856 48905

57 4605558 25335

59 4717160 HA23761

61 4334662 64962

63 4301564 43087

65 4495066 25331

67 736-014268 43081

69 4432670 710-0367

71 2540823625

72 4300073 44062

74 14275 R19131316

76 6377377 48049

78 732-030679 49264

80 4300981 25562

82 2556349326

3 Cotter Pin, 1/8" x 1-1/2"3 Hex Bolt, 1/2-13 x 1" (Grade 5)6 Flat Washer, 5/8" x 1-1/4" x 16 Ga.1 Tilt Bracket Extension Strap1 Tilt Bracket1 Hex Bolt, 3/8-16 x 2" (Grade 5)1 Hex Bolt, 3/8-16 x 1-3/4" (Grade 5)1 Lift FrameAssembly5 Hex Bolt, 5/16-18 x 1-3/4" (Grade 5)6 Cotter Pin, 1/8" x 1-1/4"1 Dump Pivot Bracket1 Dump Control Rod1 Dump Control Pin1 Compression Spring1 Spring Pin, 1/8" x 1"1 Pin Stop Bracket1 Nylock Nut, #10-321 Hose Clamp1 Truss-Head Bolt, #10-32 x 5/8"1 Bucket Assembly3 Hex Nut, 3/8-162 Hex Bolt, 3/8-16 x 1-1/4" (Grade 5)2 Carriage Bolt,1/4-20x 3/4" (Grade5)2 Tilt Stop Bracket3 Flat Washer, 1/4"8 Flat Washer, 5/16"2 Carriage Bolt, 5/16" x 1" (Grade 5)2 Hex Bolt, 5/8-11 x 1-1/2" (Grade 5)1 Spacer, 3/8" I.D. x 7/8"O.D x 3/8"1 Spacer, 3/8" I.D. x 5/8"O.D x 1/4"1 Extension Spring2 Clevis Pin, 1/2" x 1"1 Cotter Pin, 1/8" x 3/4"2 Flat Washer, 3/8" x 13/16" x 1/16"1 Index Bracket Assembly1 Index Rod1 Spring, Compression1 Lift Handle Tube2 Flat Washer, 3/4"1 Right (LT) Side Plate1 Left (LT) Side Plate1 Owner's Manual

* Purchase Common Hardware Locally

19

NOTES

20

NOTES

21

NOTES

22

5.oo0

e.-

o0

0 i..0e- oo

_b..._o.,2"

_'mo _

_ E

€- _,-

oZ_0 °coo o

am _ €_ e.

,_ 0 _

€- _ '--

;.E °

o o

"_ o

_o

e-

|

| _

|

|

|

|

|

|

|

|

|

1_

|

|

|

|

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

&CAUTION: DO NOT OPERATE YOUR TRACTOR AND SCOOP ON A SLOPEIN EXCESS OF 10 DEGREES. BE SURE OF YOUR TRACTOR'S TOWINGAND BRAKING CAPABILITIES BEFORE OPERATING ON ASLOPE. AVOIDANY SUDDEN TURNS OR MANEUVERS WHILE ON A SLOPE.

¢o

For repair of major brand appliances in your own home...no matter who made it, no matter who sold it!

for repair, call for the location of your nearest Sears Parts & Repair Center.

t -800-488-1222 Anytime, day or night

www.sears.com

For the replacement parts, accessories and owner's manualsthat you need to do-it-yourself, call Sears PartsDirectSM !

1-800-366-PART 6am=11p.m.CST,

(1-800-366-7278) 7 days a week

TM® Registered Trademark / Trademark of Sears, Roebuck and Co.

© Sears, Roebuck and Co ® Marca Registrada / TM Marca de Fabrica de Sears, Roebuck and Co

Documents

Craftsman Front Scoop