Cotton process for double production and cost reduction Introducing first time in world: Latest SRP-NANOtechnology for dyeing and printing of cotton fabrics: ADVANTAGE OF THE SRP- NANO TECHNOLOGY:1. 100% Elimination of desizing2. 100% Elimination of mercerization3. Only one drying4. Water saving up to 72%5. 100 % elimination of costly R.O. Treatment from E.T.P.6. 60% less effluent load7. 2-3 Times more production8. Big saving in energy.9. Successfully launched in Corporate like: Bombay Dyeing, Raymond and a lot more.
Citation preview
ESCON INTERNATIONAL Manufacturers of Nano-technology based
performance chemicals for textiles
--------------------------------------------------------------------------------------------------------------------------
706 Nistha Ashish Apartment, Opposite Uma Bhawan, Bhatar Road,
Surat-395007
Cotton process for double production and cost reduction
Introducing first time in world: Latest SRP-NANO technology for
dyeing and printing of cotton fabrics: ADVANTAGE OF THE SRP- NANO
TECHNOLOGY: 1. 100% Elimination of desizing 2. 100% Elimination of
mercerization 3. Only one drying 4. Water saving up to 72% 5. 100 %
elimination of costly R.O. Treatment from E.T.P. 6. 60% less
effluent load 7. 2-3 Times more production 8. Big saving in energy.
9. Successfully launched in Corporate like: Bombay Dyeing, Raymond
and a lot more. DESCRIPTION OF PROCESS WITH OUR PROCEDURE- COMPARE
WITH YOUR RUNNING PROCESS: On Jigger (Innovative process for
pretreatment and dyeing printing of cotton fabrics) 1) Preparing of
chemical bath with our special Nano chemicals. (A) RX-54 3% (W.O.F)
(B) LN-35 1% (W.O.F) (c) NR-55 1% (W.O.F) (D) XL-777 2% (W.O.F) And
15 Degree caustic soda Now start Grey padding with the above
solutions. 2) Hold the fabric for 12-24 Hours on Trolley. 3)
Loading on jigger and start hot wash-4 end (80-90 degree) Ideal hot
wash liquor: With 2-3% caustic soda. 4) To cold wash: Add hydrogen
peroxide and hypochlorite as usual. 5) PH as usual 6) Now RFD is
ready for dyeing or printing as usual -----------------------------
On jet dyeing -------------- 1) Prepare chemical bath in jet: (A)
RX-54 3% (W.O.F) (B)LN-35 1% (W.O.F) (c) NR-55 1% (W.O.F) (D)
XL-777 2% (W.O.F) And 6% Caustic soda (W.O.F) and if required add
non silicon deformer. 2) Now start Grey loading and run for one
hour at room temperature. 3) Drain the solution. 4) Now add 6%
caustic soda, 0.5% soda ash and 1% Hydrogen peroxide. 5) Increase
the temperature up to 100 Degree and hold temperature for 45
Minutes. 6) After 45 Minutes drain the solution. 7) Run hot wash
for 20 minutes at 90 degree. 8) One cold wash at 3% peroxide, 1%
soda ash, Required hypochlorite and stabilizer (sodium silicate)
and increase temperatures up to 90 degree Options: *Add NID as
required if materials are for dyeing
*Add whitener if materials are for printing 9) Run for 45
minutes at 90 Degree 10) Give Cold wash, PH correction as required
and take goods out. 11) RFD is Ready (Ready for dyeing or printing)
For trial and dealership please call: 9824167374 or send email :
[email protected]
