Upload
donhu
View
223
Download
5
Embed Size (px)
Citation preview
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Diamond Products
Core Barrels
Drill Rods
Water Swivels
Hoisting Plugs
Casing
Recovery Tools
Adapter Subs
Conversion Kits
Tools
Technical Data
REV 01-DEC-06
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Diamond Products
Impregnated Bits
Reaming Shells
Casing Shoes
Casing Bits
Bit and Shell Gauges
Options and SpecialtyDiamond Products
NOTE: The diamond tools used for PV and PV3are the same as PQ and PQ3.
Surface Set Bits are available on request.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Impregnated Bits
Boart Longyear introduces metal coated diamond impregnated bits -the latest in industrial diamond technology.• Significantly outperforms the successful Series range in both drilling
speed and bit life.• Protects the diamond from oxidation and surface degradation
during manufacturing.• Inhibits the premature "pull-out" of the diamond.• Increases the number of cutting edges exposed to the rock.• Available in multiple standard configurations and selected on the
basis of relative rock hardness and ground conditions.
* Available on special request.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual or the Diamond Products FieldManual for additional operating information.Standard: Designed to handle a wide variety of formations.
Abrasive: Recommended for broken "abrasive" drilling condtions. Forharder rock with broken conditions use a higher number bit tomaintain good drilling speeds.
Competent: Free cutting design for fast penetration in very hard"competent" rock or for use on lower powered rigs and geotechnicalapplications.
Express Geometry: Bits are supplied with additional intermediatewaterways which provide increased flushing. The reduced bit facearea allows for higher penetration rates with less bit weight required.Recommended when polishing occurs with standard geometry.
NOTE: "Standard Gauge" bits are defined as having a set outsidediameter which is 0.56mm (0.022") smaller than "ReamingShell Gauge". For more detailed information on "StandardGauge vs Reaming Shell Gauge" impregnated bits, refer tothe ITHT Product Manual.
PQ Impregnated BitsStandard Reaming ShellGeometry Geometry
Alpha01 * *Alpha01 Abrasive * *Alpha02 4052474 4050296Alpha04 * *Alpha06 * *Alpha06 Abrasive * *Alpha07 * *Alpha07 Abrasive * *Alpha07 Competent * *Alpha08 * *Alpha08 Abrasive * *Alpha08 Competent * *Alpha09 * *Alpha09 Competent * *Alpha10 * *Alpha10 Competent * *
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Impregnated Bits
* Available on special request.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual or the Diamond Products FieldManual for additional operating information.
Face DischargeWaterway
Drilling Fluid
Core Lifter Case
Bit
Boart Longyear introduces metal coated diamond impregnated bits -the latest in industrial diamond technology.• Significantly outperforms the successful Series range in both drilling
speed and bit life.• Protects the diamond from oxidation and surface degradation
during manufacturing.• Inhibits the premature "pull-out" of the diamond.• Increases the number of cutting edges exposed to the rock.• Available in multiple standard configurations and selected on the
basis of relative rock hardness and ground conditions.• Triple-tube bits are used with Boart Longyear triple-tube core
barrels. The design of the face discharge waterways and core liftercase forces the drilling fluid to the bit face. Core can be recoveredand inspected in a virtually undisturbed condition.
Standard: Designed to handle a wide variety of formations.
Abrasive: Recommended for broken "abrasive" drilling condtions. Forharder rock with broken conditions use a higher number bit tomaintain good drilling speeds.
Competent: Free cutting design for fast penetration in very hard"competent" rock or for use on lower powered rigs and geotechnicalapplications.
NOTE: "Standard Gauge" bits are defined as having a set outsidediameter which is 0.56mm (0.022") smaller than "ReamingShell Gauge". For more detailed information on "StandardGauge vs Reaming Shell Gauge" impregnated bits, refer tothe ITHT Product Manual.
PQ3 Impregnated BitsStandard Reaming ShellGeometry Geometry
Alpha01 * 4050880Alpha01 Abrasive * *Alpha02 * 4050303Alpha04 4052363 4051263Alpha06 * *Alpha06 Abrasive * *Alpha07 * *Alpha07 Abrasive * *Alpha07 Competent * *Alpha08 * *Alpha08 Abrasive * *Alpha08 Competent * *Alpha09 * *Alpha09 Competent * *Alpha10 * *Alpha10 Competent * *
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Reaming Shells
The recommended practice is to alternate two reaming shells in eachhole drilled to maintain hole diameter. Upon bit changes, the reamingshell should be checked for wear with the bit and shell wear gauge.Failure to observe these recommended practices will result in either apoorly stabilized bit or an undersized hole that will require costlyreaming.
Reaming Shells - Sourced from Americas
PQ/PQ3 Standard Reaming Shell 3522862
** Available on special request.
NOTE: Refer to the ITHT Product Manual or the Diamond ProductsField Manual for additional operating information.
Reaming Shells - Sourced from Australasia
PQ/PQ3 Heavy Duty Impregnated 4102770PQ/PQ3 Adaptor Coupling Impregnated 4103690PQ/PQ3 Surface Set 4102395PQ/PQ3 Adaptor Coupling Surface Set 4102435PQ/PQ3 Rod Line Surface Set **
Reaming Shells - Sourced from Europe
PQ/PQ3 Impregnated 49450PQ/PQ3 Surface Set 48797PQ/PQ3 Premium Stabilized **
Reaming Shells - Sourced from South Africa
PQ Ringset **
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Casing Shoes
Casing ShoeThe inside diameter of the casing shoe is not set with diamonds andis flush with the inside diameter of the casing, permitting free passageof the core barrel past the casing shoe.
Applications:• The casing shoe is threaded to the end of the casing string for
penetration through overburden.• Assists in seating the casing into the bedrock, providing a tight
seal for the drilling fluids to flow through to the surface.• Used to ream the casing downward when advancing a casing
string in an existing hole with the rod string still in place.
** Available on special request.
NOTE: Refer to the ITHT Product Manual or the Diamond ProductsField Manual for additional operating information.
Casing Shoes - Sourced from Australasia
PW Standard Impregnated 4101564PW Heavy Duty Impregnated **PW Surface Set **
Casing Advancer Shoes - Sourced from Australasia
PW Impregnated **PW HD 6mm 4101911
Casing Shoes - Sourced from Europe
PW V-Ring 8177PW Oversize 49463
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Casing Bits
Casing BitThe inside diameter of the casing bit is set with diamonds and issmaller than the casing shoe. It will not permit the passage of thecore barrel.
Applications:• Used when deep or difficult overburden is encountered.• When reaming operations are completed, the casing string is
removed from the hole and a casing shoe is substituted for acasing bit before normal drilling operations recommence.
Casing Bits
PWT V-Ring 509154
NOTE: Refer to the ITHT Product Manual or the Diamond ProductsField Manual for additional operating information.
Casing Bits - Sourced from Europe
PWT V-Ring 52742
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Bit and Shell Gauge
Bit and Shell Gauge
PQ/PQ3 Bit and Shell Wear Gauge 102486
Bit and Shell Wear GaugeAs good practice, the diameter of surface set bits and reaming shellsshould be measured. This will ensure that the hole size is maintained.All holes should be collared with a full gauge reaming shell. Ondeeper holes, two or more shells should be alternated in the hole tomaintain the hole size. Reaming shells should be gauged every tripout of the hole.The practice of gauging bits is more common with surface set bits.Impregnated bits typically maintain their gauge until totally consumed.
NOTE: Refer to the ITHT Product Manual or the Diamond ProductsField Manual for additional operating information.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Options and Specialty Diamond Products
Hard FacingIn order to improve the protection of the blank for bits, reaming shell,or casing shoes, three spiral strips of hard tungsten carbide can beapplied over the full length of the blank.
Super Flush WaterwaysWaterways designed to 6.35mm (0.25") width to allow the improvedpassage of drilling fluids.
Reinforced WaterwaysFor surface set bits, matrix protection can be provided by supplyingtungsten carbide inserts on the leading edge of the waterways.
Extra Hard MatrixFor more abrasive drilling conditions, an increased erosion resistantmatrix is available for surface set bits.
Non-Coring BitsTheir design provides reinforcement of the center of the bit to preventexcessive wear of this critical area. Various center designs, includingpencil core and crowsfoot types, are available to suit your particularneeds. Water courses are carefully engineered to provide fast andcomplete evacuation of the cuttings produced by this type of tool,thereby increasing the penetration rates in all types of formations andincreasing bit life. Other non-coring bits are available for hydroelectricgrouting applications.
Specialty ProductsBoart Longyear manufactures other special products such aspolishing bits and hole openers to complete the diamond product line.Contact your Boart Longyear representative for more information.
For your specialty diamond product requirements, please contact yourlocal Boart Longyear representative.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Core Barrels
ConventionalPVPV3
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Core Barrels - PV
PV Core Barrel
Head Assembly
Inner Tube Components
Outer Tube Components
Extended Core Barrels
Spare Parts Kit
NOTE: All core barrels will require someassembly upon receipt of shipment.Please refer to Packaging Information andAssembly Instructions.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Core Barrel - PV
Core Barrels kg lbs
1-10 3546995 PV Core Barrel 1.5 m / 5 ft 77.8 171.01-10 3546996 PV Core Barrel 3.0 m / 10 ft 122.7 270.0
Standard Configuration Qty
1 3546997 PV Head Assembly* 12 26159 Inner Tube, 1.5 m / 5 ft 12 26534 Inner Tube, 3.0 m / 10 ft 13 26161 Stop Ring 14 26162 Core Lifter, Fluted 15 52172 Core Lifter Case 16 3543802 Outer Tube, 1.5 m / 5 ft 16 3543801 Outer Tube, 3.0 m / 10 ft 17 44923 Inner Tube Stabilizer 18 26168 Thread Protector 19 3541994 ITHT Product Manual (not shown) 1
10 306390 Safety Poster (not shown) 1
Additional options available.
* See the head assembly section for a detailed configuration and available options.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Boart Longyear offers a field proven standard PV core barrelconsisting of the head assembly (item 1), inner tube components(items 2-5), and outer tube components (items 6-8). The In-The-HoleTools Product Manual and core barrel Safety Poster are included withall core barrels.
How to Order:To order a standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.
Options:There are alternatives to the standard core barrel which are indicatedby a “ ”. To view these options refer to the head assembly, inner tubecomponents and/or outer tube components sections.
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from the head assembly,
inner tube components and/or outer tube components sections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
1
2
3
4
5
6
7
8
2-7/8 API REGThread
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Head Assembly - PV
Options:There are alternatives to the standard head assembly which areindicated by a “ ”. If options are ordered, the standard headassembly is supplied with the options shipped as separate items (notinstalled).
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from this page, and/or the
options from the inner tube and outer tube components sections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
Head Assembly Options Qty
4A 3540300 Washer 2
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Head Assembly kg lbs
1-10 3546997 PV Head Assembly 33.2 73.0
Standard Configuration Qty
1 3546980 Outer Tube Head 2-7/8 API REG Thread 12 44574 Hex Nut 13 3541058 Spindle, Hollow 14 3540308 Shut-Off Valve, Hard 25 3540300 Valve Adjusting Washer 26 3540299 Washer, Tapered 17 24528 Thrust Bearing 38 3540794 Spindle Bearing 19 17447 Grease Fitting 1
10 3540755 Compression Spring 111 3544324 Washer, 1-1/4" Narrow 112 103062 Stover Lock Nut, 1-1/4 UNC 113 3543805 Inner Tube Cap Assembly (A - E ) —
13A 62374 Stainless Steel Ball, 22 mm 113B 3540737 Bushing 113C 3540745 Check Valve Body 113D 100865 Spring Pin 113E 3543804 Inner Tube Cap 1
1
2
3
4
5
6
5
4
7
10
13E
13C
4A
4A
2-7/8 API REGThread
7
9
7
8
11
12
13A
13D
13B
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Inner Tube Components - PV
Standard Configuration Qty
1 3546997 PV Head Assembly* 12 26159 Inner Tube, 1.5 m / 5 ft 12 26534 Inner Tube, 3.0 m / 10 ft 13 26161 Stop Ring 14 26162 Fluted Core Lifter 15 52172 Core Lifter Case 1
* See the head assembly section for a detailed configuration and available options.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
To order inner tube components apart from the core barrel, pleaseuse the numbers provided and specify any options you may require. Ifordering these components as part of a core barrel, please refer tothe ordering instructions below. All inner tube components areshipped unassembled.
Options:There are alternatives to the standard inner tube components whichare indicated by a “ ”. If optional items are chosen, they will replacethe standard items when the order is processed.
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from this page, and/or the
options from the head assembly and outer tube componentssections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
1
4A
2
5
3
A
4
2-7/8 API REGThread
Optional Chrome Plating
2A 26159CP Inner Tube CP 1.5 m / 5 ft 12A 26534CP Inner Tube CP 3.0 m / 10 ft 1
To order chrome plated inner tubes (full length inside diameter) use thefollowing part numbers.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Outer Tube Components - PV
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Outer Tube Components Qty
6 3543802 Outer Tube, 1.5 m / 5 ft 16 3543801 Outer Tube, 3.0 m / 10 ft 17 44923 Inner Tube Stabilizer 18 26168 Thread Protector 1
Options:There are alternatives to standard outer tube components which areindicated by a “ ”. If optional items are chosen, they will replace thestandard items when the order is processed.
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from this page, and/or the
options from the head assembly and inner tube componentssections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
Optional Chrome Plating
To order chrome plated outer tubes (45 cm (18 in) at both ends on theoutside diameter) use the following part numbers.
6A 3543802CP Outer Tube CP 1.5 m / 5 ft 16A 3543801CP Outer Tube CP 3.0 m / 10 ft 1
6
7
8
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Extended Core Barrels - PV
NOTE: Refer to the ITHT Product Manual for additional operatinginformation.
The inner tube coupling can be used to extend core barrels from1.5 m (5 ft) to 3.0 m, 4.5 m or 6.0 m (10 ft, 15 ft or 20 ft) lengths inconsolidated ground conditions.
Example: To assemble a 6 m (20 ft) core barrel, use a 3.0 m (10 ft)core barrel assembly plus the following:• 1-outer tube 3.0 m/10 ft• 1-inner tube 3.0 m/10 ft• 1-inner tube stabilizer• 1-inner tube coupling
Extended Core Barrels
1 38420 Inner Tube Coupling
1
Inner Tube
Lower Inner Tube
Outer Tube
Outer Tube
HeadAssembly
Inner TubeStabilizer
Inner TubeStabilizer
ReamingShell
Bit
Stop Ring
Core Lifter
Core LifterCase
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Spare Parts Kit - PV
Spare Parts Kit kg lbs
1-10 3543740 PV Core Barrel Spare Parts Kit 15.1 33.3
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Parts Qty
1 44574 Hex Nut 12 3540308 Shut-Off Valve, Hard 43 24528 Thrust Bearing 24 3540794 Spindle Bearing 15 103062 Stover Lock Nut 16 17447 Grease Fitting 27 26161 Stop Ring 28 26162 Core Lifter 209 52172 Core Lifter Case 4
10 44923 Inner Tube Stabilizer 2
Spare Parts Kits are designed to meet the average requirements for1 000 m (3,300 ft) of drilling.
1
2
3
4
7
8
9
10
6
NOTE: Hanger and Thrust bearing are the same (item 3)
5
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Core Barrels - PV3
PV3 Core Barrel
Head Assembly
Inner Tube Components
Outer Tube Components
Spare Parts Kits
NOTE: All core barrels will require someassembly upon receipt of shipment.Please refer to Packaging Information andAssembly Instruction sections.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Core Barrel - PV3
Core Barrels kg lbs
1-15 3547178 PV3 Core Barrel 1.5 m / 5 ft 83.3 183.31-15 3547179 PV3 Core Barrel 3.0 m / 10 ft 132.3 291.1
Standard Configuration Qty
1 3546997 PV Head Assembly* 12 26182 Pump-Out Adapter, 3/4” NPT-F** 13 26662 Piston Plug** 14 26178 O Ring 15 26179 Core Ejection Piston 16 26180 Split Tube, 1.5 m / 5 ft 16 26710 Split Tube, 3.0 m / 10 ft 17 26159 Inner Tube, 1.5 m / 5 ft 17 26534 Inner Tube, 3.0 m / 10 ft 18 26176 Stop Ring 19 26177 Core Lifter, Fluted 1
10 26160 Core Lifter Case 111 3543802 Outer Tube, 1.5 m / 5 ft 111 3543801 Outer Tube, 3.0 m / 10 ft 112 44923 Inner Tube Stabilizer 113 26168 Thread Protector 114 3541994 ITHT Product Manual (not shown) 115 306390 Safety Poster (not shown) 1
Additional options available.
* See the head assembly section for a detailed configuration and available options.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Boart Longyear offers a field proven standard HV3 core barrel. Itconsists of the head assembly (item 1), inner tube components (items2-10), and outer tube components (items 11-13). The In-The-HoleTools Product Manual and core barrel Safety Poster are included withall core barrels.
Triple-tube core barrels are commonly selected when drilling coal, claybearing or highly fractured formations. A second inner tube (splitlengthwise) is contained inside the standard inner tube. The coreejection piston protects the core from pressurized drilling fluid whenthe split inner tube, containing the core sample, is pumped out of thestandard inner tube. Upon removal, one half of the split tube is liftedoff to reveal the undisturbed core sample.
How to Order:To order a standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.
Options:There are alternatives to the standard core barrel which are indicatedby a “ ”. To view these options refer to the head assembly and/orouter tube components sections.
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from the head assembly
and/or outer tube components sections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
3
2** These items are required to pump the coreout of the inner tube. Remove the headassembly from the inner tube, insert the pistonplug and thread the pump out adapter on tothe inner tube.
Fluid pressure supplied by optional handpump group (p/n 26738) or pump-out group(p/n 26742). See Tools section.
13
1
4
9
11
12
7
6
5
8
10
2-7/8 API REGThread
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Options:There are alternatives to the standard head assembly which areindicated by a “ ”. If options are ordered, the standard headassembly is supplied with the options shipped as separate items (notinstalled).
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from this page, and/or the
options from the inner tube and outer tube components sections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
Head Assembly - PV3
Head Assembly Options Qty
4A 3540300 Washer 2
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Head Assembly kg lbs
1-10 3546997 PV Head Assembly 33.2 73.0
Standard Configuration Qty
1 3546980 Outer Tube Head 2-7/8 API REG thread 12 44574 Hex Nut 13 3541058 Spindle, Hollow 14 3540308 Shut-Off Valve, Hard 25 3540300 Valve Adjusting Washer 26 3540299 Washer, Tapered 17 24528 Thrust Bearing 38 3540794 Spindle Bearing 19 17447 Grease Fitting 1
10 3540755 Compression Spring 111 3544324 Washer, 1-1/4" Narrow 112 103062 Stover Lock Nut, 1-1/4 UNC 113 3543805 Inner Tube Cap Assembly (A - F ) —
13A 62374 Stainless Steel Ball, 22 mm 113B 3540737 Bushing 113C 3540745 Check Valve Body 113D 100865 Spring Pin 113E 3543804 Inner Tube Cap 1
1
2
3
4
5
6
5
4
7
10
13E
13C
4A
4A
2-7/8 API REGThread
7
9
7
8
11
12
13A
13D
13B
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Inner Tube Components - PV3
To order inner tube components apart from the core barrel, pleaseuse the numbers provided and specify any options you may require. Ifordering these components as part of a core barrel, please refer tothe ordering instructions below. All inner tube components areshipped unassembled.
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from the head assembly
and outer tube components sections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
Standard Configuration Qty
1 3546997 PV Head Assembly* 12 26182 Pump-Out Adapter, 3/4” NPT-F** 13 26179 Core Ejection Piston** 14 26178 O Ring 15 26662 Piston Plug 16 26180 Split Tube, 1.5 m / 5 ft 16 26710 Split Tube, 3.0 m / 10 ft 17 26159 Inner Tube, 1.5 m / 5 ft 17 26534 Inner Tube, 3.0 m / 10 ft 18 26176 Stop Ring 19 26177 Core Lifter, Fluted 1
10 26160 Core Lifter Case 1
* See the head assembly section for a detailed configuration and available options.
NOTE: Chrome plated inner tubes (full length inside diameter) can notbe used with triple-tube core barrels.
Inner tube extensions for use with stabilized reaming shells cannot be used with the triple-tube core barrel.
Triple-tube core barrels can not be extended with inner tubecouplings.
Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
3
2** These items are required to pump the coreout of the inner tube. Remove the headassembly from the inner tube, insert the pistonplug and thread the pump out adapter on tothe inner tube.
Fluid pressure supplied by optional handpump group (p/n 26738) or pump-out group(p/n 26742). See Tools section.
4
75
1
6
8
9
10
2-7/8 API REGThread
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Outer Tube Components - PV3
Options:There are alternatives to standard outer tube components which areindicated by a “ ”. If optional items are chosen, they will replace thestandard items when the order is processed.
How to Order:To order a non-standard core barrel:• Select a 1.5 m/5 ft or 3.0 m/10 ft core barrel part number.• List all optional parts and part numbers from this page, and/or the
options from the head assembly and inner tube componentssections.
NOTE: For information on packaging and assembly, refer to thepackaging and/or assembly pages located at the end of thissection.
11
12
13
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Outer Tube Components Qty
6 3543802 Outer Tube, 1.5 m / 5 ft 16 3543801 Outer Tube, 3.0 m / 10 ft 17 44923 Inner Tube Stabilizer 18 26168 Thread Protector 1
Optional Chrome Plating
To order chrome plated outer tubes (45 cm (18 in) at both ends on theoutside diameter) use the following part numbers.
6A 3543802CP Outer Tube CP 1.5 m / 5 ft 16A 3543801CP Outer Tube CP 3.0 m / 10 ft 1
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Spare Parts Kit - PV3
Spare Parts Kit kg lbs
1-11 3543741 PV3 Core Barrel Spare Parts Kit 15.1 33.3
Parts Qty
1 44574 Hex Nut 12 3540308 Shut-Off Valve, Hard 43 24528 Thrust Bearing 24 3540794 Spindle Bearing 15 103062 Stover Lock Nut 16 17447 Grease Fitting 27 26176 Stop Ring 28 26177 Core Lifter, Fluted 209 26160 Core Lifter Case 4
10 26178 O Ring 511 44923 Inner Tube Stabilizer 2
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Spare Parts Kits are designed to meet the average requirements for1 000 m (3,300 ft) of drilling.
1
2
3
4
6
7
8
9
10
115
NOTE: Hanger and Thrust bearing are the same (item 3)
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Drill Rods
PHD Rod
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
PHD Rod
1 Standard HWT casing, without the identificationgroove, is NOT recommended for use as drill rod.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Thread Lubrication• Z-50 Thread Compound (p/n 306486) is the recommended thread
lubricant to reduce wear and the possibility of galling during drillingoperations.
Features:• Tapered joint with modified buttress thread form.• Exclusive electric induction surface hardening of pin thread crest
results in a hardness differential with the mating box thread surface.• Reduced thread wear and galling.• Extended service life.• Identification groove supplied on “4130 Material” ONLY.
Surface Hardened
Imperial Lengths kg lbs
1 3542519 PHD Rod, 2 ft 10.5 23.11 3540844 PHD Rod, 5 ft 25.9 57.01 3540845 PHD Rod, 10 ft 51.5 113.5
PHD/WT Thread Profile
Box Pin
Metric Lengths kg lbs
1 3541743 PHD Rod, 1.5 m 25.4 56.11 3542314 PHD Rod, 3.0 m 50.5 111.0
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Water Swivels
Surface Compact Plus Water Swivel
Hose and Connections
Spare Parts Kit
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Surface Compact Plus Water Swivel
Features:• Swivel cap complete with lifting bail for hoisting cable
applications.• #16 NPT hose connection.• AW rod box spindle connection.• Suitable for use with water or drilling mud.• Easy servicing in the field with common tools.
11
10
7
6
4
3
2
5
1413
12
19
Assembly kg lbs
1-14 3546952 Compact Plus Water Swivel 7.6 16.7
Reference only.See Adapter Sub
section.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Parts Qty
1 3546529 Swivel Cap 12 23863 Washer Spring 13 19678 O Ring 14 23861 Swivel Packing 15 3546530 Wear Sleeve 16 23866 Packing Cage 17 20324 Ball Bearing 18 3546531 Upper Swivel Body 19 3546907 Spindle 1
10 20169 O Ring 111 3546908 Thrust Ball Bearing 112 3546909 Lower Swivel Body 113 17447 Grease Fitting 114 25612 Felt Seal 1
Reference only.See Water Swivel
Hose.
#16 NPT
8
AWRod Box
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Hose and Connections - Surface
Features:• SAE 100R2 Type AT hydraulic hose.• MASHA accepted synthetic rubber cover.• 2000 psi maximum operating pressure.• Industry standard #16 JIC female swivels for easy connect/
disconnect.
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Compact Water Swivel to Pump Qty
1 17003 #16 NPT 90° Street Elbow 12 19971 #16 NPT to #16 JIC-M Adapter 23 3542419 Water Swivel Hose, 9 m (30 ft) 14 18040 Discharge Assembly, #16 NPT 1
3
2
1
4
to pump
2
#16 NPT
AWRod Box
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Spare Parts Kits
Spare Parts Kits are designed to meet the average requirements for1 000 m (3,300 ft) of drilling.
1
2
3
4
5
8
6
7
Spare Parts Kit kg lbs
1-8 3546955 Compact Plus Water Swivel — —
Parts Qty
1 23863 Washer Spring 22 19678 O Ring 63 23861 Swivel Packing 34 3546530 Wear Sleeve 25 20324 Ball Bearing 16 20169 O Ring 67 3546908 Thrust Bearing 18 25612 Felt Seal 2
NOTE: Refer to the ITHT Product Manual for additional operatinginformation.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Hoisting Plugs
Hoisting Plug AssembliesStandard
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Hoisting Plug - Standard
Assembly kg lbs
1-9 3545380 Standard Hoisting Plug Assembly 9.8 21.6
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
1
23
5
4
6
7
8
Parts Qty
1 3545376 Eye Bolt 12 37394 Spring Pin 1/4” x 2” 13 3545377 Wear Sleeve 14 3545378 Bearing Housing 15 17447 Hydraulic Grease Fitting 16 3542992 Thrust Bearing 17 3545379 Shaft Sleeve 18 3543012 Stover Lock Nut 19 3545381 Lower Housing 1
Reference only.See AdapterSub section.
9
Features:• Dependable, field proven product for surface drilling operations.• See Tech Data for hoisting capacity.• Designed with a 5:1 safety factor utilizing rated eye bolt.• 12.5 mm (0.5 in) diameter down-angled vent is incorporated into
the body to eliminate side spray from pressurized drilling fluid.• Long-life thrust roller bearing provides pivot for ease of connecting
and reduces hoisting cable winding during hoisting and lowering.• NW rod box spindle connection.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Casing
PWT Casing
Casing Drive Shoe
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Casing
Features:• Tapered joint with modified buttress thread form.
Imperial Lengths kg lbs
1 3543973 PWT Casing, 2 ft 13.1 28.81 3543974 PWT Casing, 5 ft 32.7 72.01 3543975 PWT Casing, 10 ft 65.3 144.0
Metric Lengths kg lbs
1 3543976 PWT Casing, 1.5 m 32.6 71.91 3543977 PWT Casing, 3.0 m 65.1 143.5
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Thread Lubrication• Z-50 Thread Compound (p/n 306486) is the recommended thread
lubricant to reduce wear and the possibility of galling during drillingoperations.
1
WT Thread Profile
Box Pin
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Casing Drive Shoes
Casing Drive Shoe kg lbs
1 3543989 PWT Casing Drive Shoe 4.4 9.8
NOTE: Refer to the ITHT Product Manual for additional operatinginformation.
1
Features:• Commonly used with drive hammers as a method of driving or
advancing casing.• Recommended for use with geotechnical soil sampling tools in clay,
sand and other soft formations.• Hardened surface with 45° leading edge pilot.
45° LeadingEdge Pilot
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Recovery Tools
PWT Casing Recovery Taps
HWT Casing/PHD Rod Recovery Taps
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
PWT Casing Recovery Tap
Drill Rod
To stuck or broken PWT Casing.
Parallel Wall Casing Recovery Tap kg lbs
1 3543013 PWT Casing Recovery Tap 17.8 39.1
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
1
Features:• Parallel wall, self-tapping thread allows for full penetration,
improved recovery connection and longer tap life.• NW rod box connection.• Right hand thread.
Reference only.See Adapter Subsection.
NW Rod BoxConnection
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
HWT Casing/PHD Rod Recovery Tap
Drill Rod
To stuck or broken HWT Casing/PHD Rod.
Parallel Wall Casing Recovery Tap kg lbs
1 3542968 HW/HWT Casing/PHD Rod Recovery Tap 11.4 25.0
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
1
Features:• Parallel wall, self-tapping thread allows for full penetration,
improved recovery connection and longer tap life.• NW rod box connection.• Right hand thread.
Reference only.See Adapter Subsection.
NW Rod BoxConnection
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Adapter Subs
Drill Rod Adapter Subs
Water Swivel Adapter Subs
Hoisting Plug Adapter Subs
Casing Adapter Subs
Recovery Tool Adapter Subs
Blank End Adapter Subs
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Drill Rod Adapter Subs
Drill Rod to Core Barrel kg lbs
1 3542319 HWT/PHD Rod Box to NW Rod Pin* 3.9 8.61 102912 NW Rod Pin to HWT/PHD Rod Pin 9.2 20.01 101509 HWT/PHD Rod Box to 2-7/8 API Reg Box6.3 13.8Reference only.
See Drill Rodsection.
Reference only.See Drill Rodsection.
1
* Connects Drill Rod to PW/HWT casing cutters
NOTE: Please contact your Boart Longyear sales representative forother Adapter Subs.Refer to the ITHT Product Manual for additional operatinginformation.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Water Swivel Adapter Subs
Compact Water Swivel to Drill Rod kg lbs
1 103487 AW Rod Pin to HWT/PHD Rod Pin 10.0 21.9
NOTE: Please contact your Boart Longyear sales representative forother Adapter Subs.Refer to the ITHT Product Manual for additional operatinginformation.
Features:• The rod pin threads are electric induction hardened to ensure long
life and minimize rod box thread galling, extending drill rod thread lifeand joint performance. Adapter Sub to PWT Casing kg lbs
2 3543992 HWT/PHD Rod Box to PWT Casing Pin 9.1
2
Reference only.See Water Swivelsection.
Referenceonly. SeeDrill Rodsection.
1
Reference only.See Casing section.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Hoisting Plug Adapter Subs
10,000 lb Hoisting Plug to Drill Rod/Casing kg lbs
2 102912 NW Rod Pin to HWT/PHD Rod Pin 9.2 20.32 3544177 NW Rod Pin to PWT Casing Pin 15.0 33.0
Reference only.See HoistingPlug section.
Reference only.See Drill Rod
section.
1
Adapter Sub to PWT Casing kg lbs
3 3543992 HWT/PHD Rod Box to PWT Casing Pin 9.1
2
Reference only.See Drill Rod
section.
5,000 lb Hoisting Plug to Drill Rod kg lbs
1 103487 AW Rod Pin to HWT/PHD Rod Pin 10.0 21.9
3
Features:• The rod pin threads are electric induction hardened to ensure long
life and minimize rod box thread galling, extending drill rod thread lifeand joint performance.
Reference only.See Casing
section.
Reference only.See Casing
section.
3
NOTE: Please contact your Boart Longyear sales representative forother Adapter Subs.
Refer to the ITHT Product Manual for additional operatinginformation.Reference only.
See HoistingPlug section.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Casing Adapter Subs
PWT Casing kg lbs
1 3544177 NW Rod Pin to PWT Casing Pin 15.0 33.0
Reference only.See Drill Rodsection.
Reference only.See Casingsection.
1
NOTE: Please contact your Boart Longyear sales representative forother Adapter Subs.Refer to the ITHT Product Manual for additional operatinginformation.
Features:• The rod pin threads are electric induction hardened to ensure long
life and minimize rod box thread galling, extending drill rod thread lifeand joint performance.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Recovery Tool Adapter Subs
NOTE: Please contact your Boart Longyear sales representative forother Adapter Subs.Refer to the ITHT Product Manual for additional operatinginformation.
Drill Rod to Rod/Casing Recovery Tap kg lbs
1 3542319 HWT/PHD Rod Box to NW Rod Pin 3.9 8.7
Reference only.See Drill Rodsection
Reference only.See RecoveryTools section.
1
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Blank End Adapter Subs
Drill Rod to Blank End Sub kg lbs
1 64481 NWJ Rod Box to Solid Blank — —1 40740 HQ Rod Box to Solid Blank 6.5 14.4
1 306321 HRQHP Rod Box to Solid Blank 6.5 14.42 64480 NWJ Rod Pin to Solid Blank — —2 40744 HQ Rod Pin to Solid Blank 9.1 20.0
2 306320 HRQHP Rod Pin to Solid Blank 9.1 20.0
NOTE: Please contact your Boart Longyear sales representative forother Adapter Subs.Refer to the ITHT Product Manual for additional operatinginformation.
Application:Blank end adapter subs enable you to manufacture your own adaptersubs for your requirements. They are supplied as rod pin or rod boxto either SOLID BLANK bar end or TUBING BLANK end.
Solid bar end subs are for use with hoist plugs and water swivelsONLY. They are NOT for use as cross over subs. Thread stand off isadjusted for hand tight box/pin shoulder makeup.
Do not bore solid pin end subs greater than 25 mm
(1 inch) to avoid shrinkage due to heat treat stresses.
1 2
Solid Blank Bar End Sub
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conversion Kits
Water Swivel Compact to Compact Plus
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Conversion Kits
14
3
2
Water Swivel Conversion Kit kg lbs
1-4 3546682 Compact to Compact Plus — —
Parts Qty
1 3546531 Upper Swivel Body 12 3546907 Spindle 13 3546908 Thrust Ball Bearing 14 3546909 Lower Swivel Body 1
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Tools
Inner/Outer Tube Wrenches
Pipe Wrenches
Rod Wrenches
Triple-Tube Pump-Out Groups
Relief Valve
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Inner/Outer Tube Wrenches
NOTE: Refer to the ITHT Product Manual for additional operatinginformation.
Assembly kg lbs
1-5 26171 Full Grip PQ Inner Tube Wrench 3.6 7.9
Parts Qty
1 28972 Stationary Jaw 12 28973 Swing Jaw 13 38580 Pin 24 38583 Retaining Ring 45 28259 Wrench Handle 1
1
2
33
44
44
5
NOTE: Refer to the Tech Data section for drill rod pretorque and theITHT Product Manual for additional operating information.
5
Assembly kg lbs
1-7 45804 Full Grip PQ Outer Tube Wrench — —
Parts Qty
1 45989 Stationary Jaw 22 45988 Swing Jaw 13 43485 Pin, 5/8” x 4” 14 43484 Pin, 5/8” x 2-3/4” 15 38583 Retaining Ring 46 43422 Spring 1
7 43483 Wrench Handle 12
3
65
5
1
1
4
5
7
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
* Recommended for making up “P” size drill rod, however it is notsufficient for deep holes, a hydraulic make and break system isrecommended.
NOTE: Refer to the Tech Data section for drill rod pretorque and theITHT Product Manual for additional operating information.
Pipe Wrenches
Assembly kg lbs
1-5 14942 18” Heavy Duty Pipe Wrench 2.6 5.8
Parts Qty
1 14944 Hook Jaw 12 14943 Heel Jaw with Pin 13 200561 Coil and Spring 14 200562 Wrench Nut 15 — Wrench Handle (included) 1
Assembly kg lbs
1-5 14945 24” Heavy Duty Pipe Wrench 4.3 9.4
Parts Qty
1 14947 Hook Jaw 12 14946 Heel Jaw with Pin 13 200563 Coil and Spring 14 200564 Wrench Nut 15 — Wrench Handle (included) 1
Assembly kg lbs
1-5 14948 36” Heavy Duty Pipe Wrench 8.4 18.6
Parts Qty
1 14950 Hook Jaw 12 14949 Heel Jaw with Pin 13 200565 Coil and Spring 14 200566 Wrench Nut 15 — Wrench Handle (included) 1
Assembly kg lbs
1-5 14951 48” Heavy Duty Pipe Wrench* 12.7 28.0
Parts Qty
1 14953 Hook Jaw 12 14952 Heel Jaw with Pin 13 200567 Coil and Spring 14 200568 Wrench Nut 15 — Wrench Handle (included) 1
3
2
41
2
35
Estimated Torque
45 KG (100 LB) HAND LOAD18” Heavy Duty Pipe Wrench ..................................................... 200 Nm (150 ft lbf)24” Heavy Duty Pipe Wrench ..................................................... 270 Nm (200 ft lbf)36” Heavy Duty Pipe Wrench ..................................................... 400 Nm (300 ft lbf)48” Heavy Duty Pipe Wrench ..................................................... 540 Nm (400 ft lbf)
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
* For making up HWT casing/PHD rod. Does not provide sufficientmake up torque for drilling.
NOTE: Refer to the Tech Data section for drill rod pretorque and theITHT Product Manual for additional operating information.
Rod Wrenches
5
Assembly kg lbs
1-7 45792 HWT Casing/PHD Rod Wrench* 7.6
Parts Qty
1 45987 Stationary Jaw 22 45986 Swing Jaw 13 43484 Pin, 5/8” x 4” 14 43485 Pin, 5/8” x 2-3/4” 15 38583 Retaining Ring 46 43422 Spring 1
7 43483 Wrench Handle 12
3
65
5
1
1
4
5
7
Estimated Torque
45 KG (100 LB) HAND LOADHWT Casing/PHD Rod Wrench ................................................. 200 Nm (150 ft lbf)
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Triple-Tube Pump-Out Groups
Fluid pressure supplied by optional hand pump group or pump-out groupis required to pump the second inner tube (split lengthwise) out of thestandard inner tube.
Hand Pump-Out Group Qty
1-8 26738 Hand Pump-Out Group consisting of:1 29257 Quick Coupling 1/2” NPT-F 1
2 29258 Quick Coupling 1/2” NPT-M 13 20829 90° Street Elbow 3/4” NPT 14 21413 Hex Bushing 3/4” x 1/2” 25 26739 Hose Assembly, 8 ft x 1/2” NPT-M 16 26740 Hand Pump 17 31746 Suction Pipe 3/4” x 24” length 18 17905 Close Nipple 1/2” NPT 1
Pump-Out Group Qty
1-7 26742 Pump-Out Group consisting of:1 18922 Hex Bushing 1-1/4” x 1/2” NPT 1
2 26739 Hose Assembly, 8 ft x 1/2” NPT-M 13 26741 Globe Valve 1/2” NPT 14 17905 Close Nipple 1/2” NPT 25 29257 Quick Coupling 1/2” NPT-F 1
6 29258 Quick Coupling 1/2” NPT-M 17 21413 Hex Bushing 3/4” x 1/2” 1
2
1
3
6
57
8
4
2
1
3
65
7
4
Water Pumpreference only.
To Water Swivel.See Water Swivel
Section.
4
4
To Pump-OutAdapter. See
Triple-Tube CoreBarrel Section.
To Pump-OutAdapter. See
Triple-Tube CoreBarrel Section.
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Relief Valve
Assembly kg lbs
1-8 3546492 Relief Valve — —
NOTE: Refer to the Tech Data section for technical specifications andthe ITHT Product Manual for additional operating information.
Parts Qty
1 21841 Adjusting Screw 12 22179 Jam, Brass Nut 13 3546493 Body 14 3546494 Spring Guide 25 24313 Spring 26 3546495 Ball Holder 17 21837 Steel Ball, 15/16” 48 3546496 Seat 4
This rugged pressure relief valve ensures protection of your pumpduring drilling operations. It automatically snaps to full open positionwhen the predetermined pressure is exceeded. The pressure settingcan be adjusted within the operating range by simply turning theadjusting screw on the top of the valve.
1
2
3
4
5
6
7
8
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Technical Data
Nominal Dimensions
Drilling Guidelines
Rod Operating Specifications
Conventional Coring System PV
12/06-MKT1644 P/N 3543105-M
© 2006 Boart Longyear Inc. Boart Longyear Inc. is constantly striving to improve its products and must therefore, reserve the right to change designs, materials, specifications and price without notice.
BOART LONGYEAR
Nominal Dimensions
HOLE DIAMETER (REAMING SHELL GAUGE) ..... 122.28/122.78 mm (4.814/4.834 in)HOLE VOLUME (REAMING SHELL GAUGE) ................................ 11.80 L/m (0.95 gal/ft)CORE DIAMETER/BIT INSIDE DIAMETER
PQ .......................................................................... 84.84/85.09 mm (3.340/3.350 in)PQ3 ........................................................................ 82.93/83.19 mm (3.265/3.275 in)
BIT OUTSIDE DIAMETER ........................................ 121.92/122.43 mm (4.800/4.820 in)BIT KERF WIDTH
PQ .................................................................................................... 19.0 mm (0.74 in)PQ3 .................................................................................................. 19.8 mm (0.78 in)
LOCKING COUPLING OUTER DIAMETERConventional ........................................................................... 122.05 mm (4.805 in)
CORE BARREL OUTER TUBEOuter Diameter ............................................................................. 117.5 mm (4.62 in)Inner Diameter ............................................................................. 103.2 mm (4.06 in)
CORE BARREL INNER TUBEOuter Diameter ............................................................................... 95.2 mm (3.75 in)Inner Diameter ............................................................................... 88.9 mm (3.50 in)
ROD BODY (HWT 4130 Casing/PHD Rod)Outer Diameter ............................................................................ 114.3 mm (4.50 in)Inner Diameter ............................................................................ 101.6 mm (4.00 in)
ROD PIN END LENGTHHWT 4130 Casing/PHD Rod ...................................................... 44.45 mm (2.47 in)Threads per Inch .................................................................................................... 2.5
ROD WEIGHT (HWT 4130 Casing/PHD Rod) ................................ 17.4 kg/m (11.7 lb/ft)ROD CONTENT VOLUME (HWT 4130 Casing/PHD Rod) ............... 8.1 L/m (0.65 gal/ft)ROD DISPLACEMENT VOLUME (HWT 4130 Casing/PHD Rod) .. 2.17 L/m (0.17 gal/ft)ROD/HOLE ANNULUS VOLUME (HWT 4130 Casing/PHD Rod) . 1.57 L/m (0.13 gal/ft)PW CASING
Outer Diameter ............................................................................. 139.7 mm (5.50 in)Inner Diameter ............................................................................. 127.0 mm (5.00 in)Weight ......................................................................................... 21.4 kg/m (14.4 lb/ft)
Technical Data
Drilling Guidelines
RECOMMENDED FLOW.................................................................................... 68 to 87 L/min (18 to 23 gpm)
BIT WEIGHT RANGE................................................................................... 23 to 45 kN (5,000-10,000 lbf)
BIT PENETRATION @ 800 rpmRate @ 80 r/cm (200 rpi) ....................................................... 10 cm/min (4.0 in/min)Rate @ 100 r/cm (250 rpi) ...................................................... 8 cm/min (3.2 in/min)
BIT PENETRATION @ 500 rpmRate @ 80 r/cm (200 rpi) ......................................................... 6 cm/min (2.5 in/min)Rate @ 100 r/cm ( 250 rpi) ...................................................... 5 cm/min (2.0 in/min)
WATER SWIVEL ROTATING LOAD RATINGCompact Plus ............................................................................... 4540 kg (10,000 lb)
HOISTING PLUG STATIC LOAD RATINGStandard ........................................................................... 5:1 = 6,800 kg (15,000 lb)......................................................................................... 3:1 = 11 300 kg (25,000 lb)
WIRELINE CABLE BREAKING STRENGTH4.8 mm (3/16 in) Swaged ............................................................. 24.5 kN (5,500 lbf)
RATED MAXIMUM DEPTH .................................................................... 1 500 m (4,900 ft)RATED MAXIMUM DRILLING PULLBACK ..................................... 451 kN (101,000 lbf)RATED MAXIMUM DRILLING TORQUE* ...................................... 4 065 Nm (3,000 ft lbf)RECOMMENDED MINIMUM MAKE-UP TORQUE to 1 000 m (3,280 ft) depth*
.................................................................................................... 1 015 Nm (750 ft lbf)RECOMMENDED MINIMUM MAKE-UP TORQUE FOR DEEP HOLES*
over 1 000 m (3,280 ft) ......................................................... 3 400 Nm (2,500 ft lbf)MIDBODY MINIMUM YIELD STRENGTH ....................................... 621 MPa (90,000 psi)MIDBODY MINIMUM TENSILE STRENGTH ................................. 724 MPa (105,000 psi)JOINT MINIMUM YIELD STRENGTH ............................................. 621 MPa (90,000 psi)JOINT MINIMUM TENSILE STRENGTH ....................................... 724 MPa (105,000 psi)MINIMUM PURE TENSION TO FAILURE** ...................................... 556 kN (125,000 lbf)MINIMUM PURE TORSION TO FAILURE** .............................. 20 337 Nm (15,000 ft lbf)
NOTE: Rod capacities and failure loads were determined by independent facility. Asafety factor has been applied for the above ratings (applies to new, unusedBoart Longyear rods, in a straight vertical down hole, assuming complianceto ITHT Product Manual and standard core drilling practices).Burst and collapse pressure ratings will be reduced under drilling loads.Operating torque should not exceed make-up torque.* Increase make-up torque to match operating torque as depth increases.** These failure loads are for product comparison purposes ONLY. Drilling
loads should not exceed rating values.
Rod (HWT 4130 Casing/PHD Rod) Operating Specifications
BURST PRESSURE - Box ShoulderHWT 4130 Casing/PHD Rod ................................................... 21.6 MPa (3,135 psi)PWT Casing .............................................................................. 19.0 MPa (2,760 psi)
BURST PRESSURE - MidbodyHWT 4130 Casing/PHD Rod ................................................... 62.0 MPa (9,000 psi)PWT Casing .............................................................................. 42.9 MPa (6,218 psi)
COLLAPSE PRESSURE - MidbodyHWT 4130 Casing/PHD Rod ................................................... 50.0 MPa (7,255 psi)PWT Casing .............................................................................. 28.3 MPa (4,110 psi)
Pressure Ratings (per API bulletin 5C3)