CoreBuilder 5000 Network Router Module Installation Guide for

®

CoreBuilder™ 5000 Network Router Module Installation Guide for Ethernet

http://www.3com.com/

Document Number 17-00835-3Published May 1997

As you browse through this manual, you will find links to other pages. To return to a previous view, click the left-facing double arrow button located in the Toolbar at the top of your screen. The single arrow buttons allow you to go to the first page or to the previous page.

3Com Corporation5400 Bayfront Plaza Santa Clara, California 95052-8145

Copyright © 3Com Corporation, 1997. All rights reserved. No part of this documentation may be reproduced in any form or by any means, or used to make any derivative work (such as translation, transformation, or adaptation) without permission from 3Com Corporation. Portions of this document are reproduced in whole or part with permission from third parties.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. 3Com may make improvements or changes in the products or programs described in this documentation at any time.

UNITED STATES GOVERNMENT LEGENDS:If you are a United States government agency, then this documentation and the software described herein are provided to you subject to the following restricted rights:

For units of the Department of Defense:Restricted Rights Legend: Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) for Restricted Rights in Technical Data and Computer Software Clause at 48 C.F.R. 52.227-7013.

For civilian agencies:Restricted Rights Legend: Use, reproduction, or disclosure is subject to restrictions set forth in subparagraph (a) through (d) of the Commercial Computer Software – Restricted Rights Clause at 48 C.F.R. 52.227-19 and the limitations set forth in the 3Com Corporation standard commercial agreement for the software. Unpublished rights reserved under the copyright laws of the United States.

If there is any software on removable media described in this documentation, it is furnished under a license agreement included with the product as a separate document, in the hardcopy documentation, or on the removable media in a directory file named LICENSE.TXT. If you are unable to locate a copy, please contact 3Com and a copy will be sent to you.

Federal Communications Commission Notice

This equipment was tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you must correct the interference at your own expense.

Canadian Emissions Requirements

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

EMC Directive Compliance

This equipment was tested and conforms to the Council Directive 89/336/EEC for electromagnetic compatibility. Conformity with this directive is based upon compliance with the following harmonized standards:

EN 55022 – Limits and Methods of Measurement of Radio Interference

EN 50082-1 – Electromagnetic Compatibility Generic Immunity Standard: Residential, Commercial, and Light Industry

Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which case you may be required to take adequate measures.

Compliance with this directive depends on the use of shielded cables.

Low Voltage Directive Compliance

This equipment was tested and conforms to the Council Directive 72/23/EEC for safety of electrical equipment. Conformity with this directive is based upon compliance with the following harmonized standard:

EN 60950 – Safety of Information Technology Equipment

ii

VCCI Class 1 Compliance

This equipment is in the 1st Class category (information equipment to be used in commercial or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment aimed at preventing radio interference in commercial or industrial areas.

Consequently, when the equipment is used in a residential area or in an adjacent area, radio interference may be caused to radio and TV receivers, and so on.

Read the instructions for correct handling.

Fiber Cable Classification Notice

Use this equipment only with fiber cable classified by Underwriters Laboratories as to fire and smoke characteristics in accordance with Section 770-2(b) and Section 725-2(b) of the National Electrical Code.

UK General Approval Statement

The CoreBuilder 5000 Integrated System Hub and ONline System Concentrator are manufactured to the International Safety Standard EN 60950 and are approved in the U.K. under the General Approval Number NS/G/12345/J/100003 for indirect connection to the public telecommunication network.

Trademarks

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered in other countries.

3Com, Boundary Routing, CardFacts, EtherLink, LANplex, LANsentry, LinkBuilder, NETBuilder, NETBuilder II, NetFacts, Parallel Tasking, SmartAgent, TokenDisk, TokenLink, Transcend, TriChannel, and ViewBuilder are registered trademarks of 3Com Corporation.

3TECH, CELLplex, CoreBuilder, EtherDisk, EtherLink II, FDDILink, MultiProbe, NetProbe, and ONline are trademarks of 3Com Corporation.

3ComFacts is a service mark of 3Com Corporation.

The 3Com Multichannel Architecture Communications System is registered under U.S. Patent Number 5,301,303.

AT&T is a registered trademark of American Telephone and Telegraph Company.

Banyan and VINES are registered trademarks of Banyan Systems Inc.

CompuServe is a registered trademark of CompuServe, Inc.

DEC, DECnet, DELNI, POLYCENTER, VAX, VT100, VT220, and the Digital logo are trademarks of Digital Equipment Corporation.

Hayes is a registered trademark of Hayes Microcomputer Products.

OpenView is a registered trademark of Hewlett-Packard Company.

Intel is a registered trademark of Intel Corporation.

AIX, IBM, and NetView are registered trademarks of International Business Machines Corporation.

Microsoft, MS-DOS, Windows, Windows 95, and Windows NT are registered trademarks of Microsoft Corporation.

V30 is a trademark of NEC Corporation.

NetWare and Novell are registered trademarks of Novell, Incorporated.IPX is a trademark of Novell, Incorporated.

OSF and OSF/Motif are registered trademarks of Open Software Foundation, Inc.

ONC, OpenWindows, Solaris, Solstice, Sun, Sun Microsystems, SunNet Manager, and SunOS are trademarks of Sun Microsystems, Inc.

iii

SPARCstation is a trademark licensed exclusively to Sun Microsystems Inc.

OPEN LOOK is a registered trademark of Unix System Laboratories, Inc.

UNIX is a registered trademark of X/Open Company, Ltd. in the United States and other countries.

Other brand and product names may be registered trademarks or trademarks of their respective holders.

iv

CONTENTS

ABOUT THIS GUIDE

Introduction 1Audience 1How to Use This Guide 1Conventions 2Related Documents 4

3Com Documents 4Reference Documents 4

1 INTRODUCTION

Router Module Overview 1-1Router Functions 1-1Module Architecture 1-2Router Models 1-3Typical Applications 1-3

Router Module Features 1-6FDDI Support 1-6WAN Support 1-6Protocol Translation 1-7Scalable Protocol Support 1-7WAN Optimization 1-9ATM Migration 1-9Management Support 1-9Distributed, Scalable Reliability 1-10Hot Swap Capability 1-10

2 INSTALLING THE MODULE

Precautionary Procedures 2-1Quick Installation 2-2Unpacking Procedures 2-2Preparing to Install the Router Module 2-4

Setting DIP Switches 2-4Setting the Configuration Source DIP Switch 2-5Configuring the Ethernet Backplane Connections 2-5

Verifying CPU Board Jumper Plug Positions 2-6Installing the Router Module 2-7Making NIM Connections 2-8

Making FDDI NIM Connections 2-9Connecting the Multi-Mode, Dual Attachment Station NIM 2-9Connecting the Multi-Mode, Single Attachment Station NIM 2-10Connecting the Multi-Mode Optical Bypass Switch 2-11Connecting the Single Mode, Dual Attachment Station NIM 2-11

Making Quad Serial NIM Connections 2-13Making ATM NIM Connections 2-14

ATM Connector Types 2-14ATM Distance Limitations 2-15

3 CONFIGURING THE MODULE

Configuration Overview 3-1Attaching a Management Terminal 3-2

Connecting to the Console Port 3-2Connecting to the Auxiliary Port 3-3

Configuring Cisco NIM Connections 3-3Configuring Cisco Parameters 3-3

Setting the Initial Router Module Configuration 3-4Setting General Interface Parameters 3-7Re-Starting the Interface Ports 3-7

Configuring 3Com Parameters 3-8

vi

4 MONITORING OPERATION

Monitoring Router Module LEDs 4-1Common Front Panel LEDs 4-1FDDI NIM LEDs 4-6Quad Serial NIM LEDs 4-7ATM NIM LEDs 4-9

Displaying the Router Module Configuration 4-10Using the SHOW MODULE Command 4-10Using the SHOW MODULE VERBOSE Command 4-11Using the SHOW PORT Command 4-11Using the SHOW PORT VERBOSE Command 4-12

5 TROUBLESHOOTING

Troubleshooting Startup Problems 5-1Troubleshooting Network Connection Problems 5-2Troubleshooting WAN Connection Problems 5-2Correcting Operating Malfunctions 5-3Recovering a Lost Password 5-4

A PRODUCT SPECIFICATIONS

General Specifications A-2Electrical Specifications A-3Environmental Specifications A-3Mechanical Specifications A-3

B CABLING SPECIFICATIONS

Console and Auxiliary Port Cables B-1Console Port Pinouts B-2Auxiliary Port Pinouts B-2

Quad Serial NIM Cables B-3EIA-530 DTE Synchronous Serial Cable Pinouts B-4EIA-232 DTE and DCE Serial Cable Assembly and Pinouts (DB-25) B-6EIA-449 DTE and DCE Serial Cable Assembly and Pinouts (DB-37) B-9V.35 DTE and DCE Serial CableAssembly and Pinouts B-12X.21 DTE and DCE Serial Cable Pinouts (DB-15) B-15

vii

viii

C VIRTUAL CONFIGURATION REGISTER

VCR Tasks C-1VCR Bit Definitions C-2

Boot Field C-2Setting Boot Field Values C-3Default Boot Filenames C-3

Break Function C-4Internet Protocol Broadcast Address C-5Engine Management Terminal Baud Rate C-5Bootload Failure Response C-5NVRAM Disable C-6

Changing VCR Settings C-6Enabling Booting From Flash Memory C-7

D FDDI PRECAUTIONS

FDDI Laser Safety Information D-1Processing D-2

E TECHNICAL SUPPORT

Online Technical Services E-1World Wide Web Site E-23Com Bulletin Board Service E-2

Access by Analog Modem E-2Access by Digital Modem E-2

3ComFacts Automated Fax Service E-33ComForum on CompuServe Online Service E-3

Support From Your Network Supplier E-4Support From 3Com Corporation E-5Returning Products for Repair E-6Accessing the 3Com MIB E-6Contacting 3Com Technical Publications E-7

INDEX

3COM CORPORATION LIMITED WARRANTY

FIGURES

1-1 CoreBuilder 5000 Network Router Module 1-21-2 Quad Serial Network Router Module Typical Application 1-41-3 ATM OC3 Network Router Module Typical Application 1-41-4 Dual Attachment FDDI Network Router Module Typical Application 1-52-1 Locating the Spacing Clips 2-32-2 Default Base Board DIP Switch Positions 2-42-3 CPU Board Jumper Plug Positions 2-62-4 CoreBuilder 5000 Network Router Module in a CoreBuilder 5000

Integrated System Hub 2-82-5 Multi-Mode FDDI Network Interface Connector, MIC Type 2-92-6 Making Connections to the FDDI MM, DAS NIM 2-102-7 Making Connections to the FDDI MM, SAS NIM 2-102-8 Connecting the Multi-Mode Optical Bypass Switch 2-112-9 Making Connections to the FDDI SM, DAS NIM 2-12

2-10 Making Connections to the Quad Serial NIM 2-132-11 Making Connections to the ATM NIMs 2-14

4-1 Common Front Panel LEDs 4-24-2 FDDI NIM LEDs 4-64-3 Quad Serial NIM LEDs 4-74-4 ATM NIM LEDs 4-94-5 SHOW MODULE Command Information 4-114-6 SHOW MODULE VERBOSE Command Information 4-114-7 SHOW PORT Command Information 4-114-8 SHOW PORT VERBOSE Command Information 4-12B-1 EIA-530 Cable Assembly B-4B-2 EIA-232 Serial Cable Assembly B-6B-3 EIA-449 Serial Cable Assembly B-9B-4 V.35 Serial Cable Assembly B-12B-5 X.21 Cable Assembly B-15D-1 Required Class 1 Laser Product Label D-2

ix

TABLES

1 How to Use This Guide 12 Graphic Conventions 23 Text Conventions 3

1-1 Software Feature Sets 1-82-1 Quick Installation Steps 2-22-2 Setting the Configuration Source for the Router Module 2-52-3 Configuring Backplane Connections for Ethernet Ports 2-52-4 ATM Distance Limitations 2-154-1 Front Panel LED Definitions 4-34-2 Quad Serial NIM LED Definitions 4-84-3 ATM NIM LED Definitions 4-105-1 Troubleshooting Malfunctions 5-3A-1 General Router Module Specifications A-2A-2 Electrical Router Module Specifications A-3A-3 Environmental Router Module Specifications A-3A-4 Mechanical Router Module Specifications A-3B-1 Console Port Pinout Specification B-2B-2 Auxiliary Port Pinout Specification B-2B-3 EIA-530 Cable Pinout Specifications B-5B-4 EIA-232 DTE Cable Pinouts (DB-60 to DB-25) B-7B-5 EIA-232 DCE Cable Pinouts (DB-60 to DB-25) B-8B-6 EIA-449 DTE Cable Pinouts (DB-60 to DB-37) B-10B-7 EIA-449 DCE Cable Pinouts (DB-60 to DB-37) B-11B-8 V.35 DTE Cable Pinouts (DB-60 to Winchester-Type 34-Pin) B-13B-9 V.35 DCE Cable Pinouts (DB-60 to Winchester-Type 34-Pin) B-14

B-10 X.21 DTE Cable Pinouts (DB-60 to DB-15) B-15B-11 X.21 DCE Cable Pinouts (DB-60 to DB-15) B-16

C-1 Virtual Configuration Register Bit Values C-2C-2 Boot Field Values (Configuration Register Bits 00 to 03) C-2C-3 Default Boot Filenames C-4C-4 Broadcast Address Destination Settings C-5C-5 Engine Management Terminal Baud Rate Settings C-5

xi

ABOUT THIS GUIDE

Introduction This guide describes how to install, configure, and monitor the 3Com CoreBuilder 5000 Network Router Module.

If the information in the release notes shipped with your product differs from the information in this guide, follow the release note instructions.

Audience This guide is intended for the following people at your site:

■ Network manager or administrator

■ Trained hardware installer or service personnel

How to Use This Guide

Table 1 shows the location of specific information.

Table 1 How to Use This Guide

If you are looking for: Turn to:

General information about the router module Chapter 1

Description of the router module architecture

Typical applications of the router module

Features of the router module

Procedures for unpacking and preparing to install the router module

Chapter 2

Procedures for setting the router module DIP switches

Procedures for installing the router module

Procedures for making NIM connections

2 ABOUT THIS GUIDE

Conventions Table 2 and Table 3 list conventions used throughout this guide.

An overview of the router module configuration process Chapter 3

Procedures for attaching a management terminal

Procedures for configuring Cisco NIM connections

Procedures for configuring Cisco parameters

Procedures for configuring 3Com parameters

Information for monitoring router module LEDs Chapter 4

Procedures for displaying the router module configuration

Information on troubleshooting the router module Chapter 5

Procedures for recovering a lost password

Module specifications, cable requirements, and other reference information

Appendixes A through E

Table 1 How to Use This Guide (continued)

Table 2 Graphic Conventions

Icon Type Description

Information Note

Information notes call attention to important features or instructions.

Caution Cautions alert you to personal safety risk, system damage, or loss of data.

Warning Warnings alert you to the risk of severe personal injury.

Conventions 3

Table 3 Text Conventions

Convention Description

Enter vs. Type When the word enter is used in this guide, it means type something, then press the Return or Enter key. Do not press the Return or Enter key when instructed to type.

Syntax vs. Command Syntax indicates that the general form of a command syntax is provided. You must evaluate the syntax and supply the appropriate port, path, value, address, or string. For example:

Enable RIPIP by using the following syntax:

SETDefault !<port> -RIPIP CONTrol = Listen

In this example, you must supply a port number for !<port>.

Command indicates that all variables in the command have been supplied and you can enter the command as shown in text. For example:

Remove the IP address by entering the following command:

SETDefault !0 -IP NETaddr = 0.0.0.0

For consistency and clarity, the full-form syntax (upper- and lowercase letters) is provided. However, you can enter the abbreviated form of a command by typing only the uppercase portion and supplying the appropriate port, path, address, value, and so on. You can enter the command in either upper- or lowercase letters at the prompt.

Text represented as screen display

This typeface is used to represent displays that appear on your terminal screen. For example:

NetLogin:

Text represented as commands

This typeface is used to represent commands that you enter. For example:

SETDefault !0 -IP NETaddr = 0.0.0.0

Keys Specific keys are referred to in the text as Return key or Escape key, or they may be shown as [Return] or [Esc].

If two or more keys are to be pressed simultaneously, the keys are linked with a plus sign (+). For example:

Press [Ctrl]+[Alt]+[Del].

Italics Italics are used to denote new terms or emphasis.

4 ABOUT THIS GUIDE

Related Documents This section provides information on supporting documentation, including:

■ 3Com Documents

■ Reference Documents

3Com Documents The following documents provide additional information on 3Com products:

CoreBuilder 5000 Integrated System Hub Installation and Operation Guide – Provides information on the installation, operation, and configuration of the CoreBuilder 5000 Integrated System Hub. This guide also describes the principal features of the CoreBuilder 5000 Fault-Tolerant Controller Module.

CoreBuilder 5000 Distributed Management Module User Guide – Provides information on the CoreBuilder 5000 Distributed Management Module’s operation, installation, and configuration. This guide also describes the software commands associated with the Distributed Management Module.

CoreBuilder 5000 Distributed Management Module CommandsGuide – Describes each management command by providing details on command format and use.

For a complete list of 3Com documents, contact your 3Com representative.

Reference Documents The following documents supply related background information:

Case, J., Fedor, M., Scoffstall, M., and J. Davin, The Simple Network Management Protocol, RFC 1157, University of Tennessee at Knoxville, Performance Systems International and the MIT Laboratory for Computer Science, May 1990.

Rose, M., and K. McCloghrie, Structure and Identification of Management Information for TCP/IP-based Internets, RFC 1155, Performance Systems International and Hughes LAN Systems, May 1990.

1
INTRODUCTION
This chapter contains the following sections:

■ Router Module Overview

■ Router Module Features

Router Module Overview

The 3Com CoreBuilder™ 5000 Network Router Module is a multiprotocol backplane router that operates in a 3Com® CoreBuilder 5000 Integrated System Hub.

This section describes the following topics:

■ Router Functions

■ Module Architecture

■ Router Models

■ Typical Applications

Router Functions The CoreBuilder 5000 Network Router Module (referred to in this guide as the router module) is designed to:

■ Provide the physical network interface to connect local- and wide-area networks in multiprotocol environments

■ Run standard Cisco Systems® Internetworking Operating System® (IOS) router software

■ Provide high-performance, fault-tolerant connectivity to backbone networks for Ethernet local area networks (LANs) within the CoreBuilder 5000 Integrated System

■ Deliver standards-based translation bridging and multiprotocol routing capability

1-2 INTRODUCTION

■ Internetwork Asynchronous Transfer Mode (ATM), Fiber Data Distributed Interface (FDDI), or wide area network (WAN) connections with four Ethernet backplane networks

■ Support the CoreBuilder 5000 Integrated System backplane for connectivity to 4 of 8 CoreBuilder 5000 Ethernet backplane networks

■ Act as the Simple Network Management Protocol (SNMP) agent for in-band or out-of-band management by any SNMP-compliant network management application or the 3Com Transcend® Enterprise Manager

Module Architecture The router module (Figure 1-1) occupies three slots in the CoreBuilder 5000 Integrated System Hub.

Figure 1-1 CoreBuilder 5000 Network Router Module

Network Interface Module(optional NIM 1)

Faceplate

CPU board

Base board (integrated NIMs 2 and 3)

Router Module Overview 1-3

The base router module consists of a CoreBuilder 5000 14-inch base board with an attached CPU board. Both the base board and the CPU board plug directly into the CoreBuilder 5000 backplane.

The base router module provides four Ethernet backplane connections (complex port connections), any one of which you can connect to any one of 8 CoreBuilder 5000 backplane networks. The Ethernet ports are equivalent to Cisco Systems IOS interface connections.

You can mount any one of multiple standard Cisco Systems Network Interface Module (NIM) types on the base board to provide additional routing connections (Cisco Systems NPM connections) for various protocol types (see Figure 1-1). Each NIM type requires a unique 3Com faceplate.

Router Models The router module is available in the following configurations:

Base – Includes 4 Ethernet backplane connections.

FDDI MM, DAS – Multi-mode, dual attachment station/4 Ethernet backplane connections.

FDDI MM, SAS – Multi-mode, single attachment station/4 Ethernet backplane connections.

FDDI SM, DAS – Single mode, dual attachment station/4 Ethernet backplane connections.

Quad Serial – 4 synchronous serial/4 Ethernet backplane connections.

ATM OC3, MM – Multi-mode fiber optic cable/4 Token Ring backplane connections.

ATM OC3, SM – Single mode fiber optic cable/4 Token Ring backplane connections.

Typical Applications Figure 1-2, Figure 1-3, and Figure 1-4 show typical applications of the Quad Serial, ATM OC3, and FDDI router modules.

1-4 INTRODUCTION

Figure 1-2 Quad Serial Network Router Module Typical Application

Figure 1-3 ATM OC3 Network Router Module Typical Application

3rd floor

4th floor

1st floor

2nd floor

3Com Edge Router Module

Remote site B

Remote site C

Remote site D

Remote site E




Dedicated or dial-up synchronous serial connections

Local site A

CoreBuilder 5000 Network Router Module

3rd floor

4th floor

1st floor

2nd floor

ATM OC-3 MM

Local site A


ATM OC-3 MM

Token Ring

Ethernet

ATM ServiceCoreBuilder 5000 Network Router Module


Router Module Overview 1-5

Figure 1-4 Dual Attachment FDDI Network Router Module Typical Application

FDDI campus backbonedual-attachment, multi-mode or single mode

3rd floor

4th floor

1st floor

2nd floor

Building B

Building A

Building C

To other sites

To other sites




1-6 INTRODUCTION

Router Module Features

This section describes the following major features of the router module:

■ FDDI Support

■ WAN Support

■ Protocol Translation

■ Scalable Protocol Support

■ WAN Optimization

■ ATM Migration

■ Management Support

■ Distributed, Scalable Reliability

■ Hot Swap Capability

FDDI Support The router module provides support for three FDDI configurations on the following two FDDI interfaces:

Multi-Mode Fiber – Can support distances of up to 2 km for both Class A Dual Attachment Stations (DAS) and Class B Single Attachment Stations (SAS).

Single Mode Fiber – Can support distances of up to 10 km for Class A Dual Attachment Stations (DAS).

The FDDI interfaces also include a connector for attachment to an external optical bypass unit. If the router module stops operating, the optical bypass unit ensures that the FDDI signal bypasses that router. The FDDI ring and other stations remain operational.

WAN Support The router module configured with a Quad Serial NIM provides four synchronous serial ports to support backbone or redundant network connections over the wide area network (WAN). The serial ports support the following connection protocols:

■ V.35

■ EIA-232

■ EIA-449

■ RS-422

■ X.21

Router Module Features 1-7

Each serial port is capable of providing T1/E1 rate connectivity. Each port operates in full duplex mode at speeds from 1,200 bits per second (bps) to 2,048 Megabits per second (Mbps).

You can configure the synchronous serial ports to support IBM® Synchronous Data Link Control (SDLC) traffic using synchronous pass through or Data Link Switching (DLSw).

Protocol Translation The router module protocol translation function allows you to extend the life of your existing network devices. The router module allows networks operating in dissimilar protocol environments to communicate while it manages up to 180 simultaneous sessions.

The router module supports the following bidirectional translations:

■ X.25 to TCP

■ X.25 to Local Area Transport (LAT)

■ X.25 to XRemote devices

■ LAT to TCP

■ LAT to TN3270 devices

Scalable ProtocolSupport

Each router module type allows you to select a specific level of protocol support to best match the needs of your application. Four Cisco IOS router software feature sets offer an increasing level of protocol support:

IP/IPX – Base feature set for use in applications requiring only IP/IPX protocols.

Desktop – Provides additional LAN support for use in applications with limited LAN protocol requirements.

Desktop plus IBM – Adds IBM support.

Enterprise – Adds top-level protocol support, including SNA (Synchronous Network Architecture) integration.

1-8 INTRODUCTION

Table 1-1 details the specific protocol support offered in each feature set.

Table 1-1 Software Feature Sets

Feature

Category

Features Included in Each Feature Set

IP/IPX Desktop Desktop plus IBM Enterprise

LAN Support IP, Bridging, LAN Extension, Host Software, Novell® IPX™

IP, Bridging, LAN Extension, Host Software, Novell IPX, DECnet™ IV, Appletalk® Phase 1 and 2

IP, Bridging, LAN Extension, Host Software, Novell IPX, DECnet IV, AppleTalk Phase 1 and 2

IP, Bridging, LAN Extension, Host Software, Novell IPX, DECnet IV, AppleTalk Phase 1 and 2, DECnet V, XNS, Banyan® VINES®, OSI, Apollo® Domain

IBM Support SRB/RSRB, SRT, DLSW+, SNA & NETBIOS™ WAN optimization (with local acknowledgment, caching, and filtering), SDLC integration, SDLC-to-LAN conversion, SDLC Transport (STUN), Frame Relay SNA Support (RFC 1490)

SRB/RSRB, SRT, DLSW+, SNA & NETBIOS WAN optimization (with local acknowledgment, caching, and filtering), SDLC integration, SDLC-to-LAN conversion, SDLC Transport (STUN), Frame Relay SNA Support (RFC 1490)TG/COS, QLLC, DSPU Concentration

Protocol Translation

X.25-to-TCP, X.25-to-LAT, and X.25-to-XRemote; LAT-to-TCP and LAT-to-TN3279 (bidirectional)

IP Routing RIP, OSPF, PIM, NHRP

RIP, OSPF, PIM, NHRP, BGP, EGP, IGRP™

RIP, OSPF, PIM, NHRP, BGP, EGP, IGRP, Enhanced IGRP

RIP, OSPF, PIM, NHRP, BGP, EGP, IGRP, Enhanced IGRP, ES-IS, IS-IS

WAN Services HDLC, PPP, X.25, Frame Relay, ISDN, SMDS, IPXWAN 2.0, ATM

WAN Optimization

Header and link compression, X.25 packet payload compression, dial-on-demand, dial backup, bandwidth-on-demand, custom and priority queuing, access lists, access security, snapshot routing

Network Management

Autoinstall, SNMP, TELNET

Router Module Features 1-9

WAN Optimization The router module provides the following features to help limit network operating costs by optimizing WAN network connections:

Dial-On-Demand Routing – A more economical alternative to a second leased line as backup, a dial-on-demand backup dials up a second line automatically if the primary WAN link fails.

Data Compression – The router module provides four types of data compression for different network environments:

■ Link compression

■ X.25 packet payload compression

■ TCP/IP header compression

■ DEC™ LAT compression

ATM Migration The router module can be upgraded to support your migration to an ATM backbone (see Figure 1-3).

Add an ATM network backbone by replacing your original router module NIM (network interface module) with one of two ATM NIM types:

■ OC-3, MM (Optical Carrier Type 3, Multi-Mode)

■ OC-3, SM (Optical Carrier Type 3, Single Mode)

Each ATM NIM type provides 155 Mbps backbone bandwidth.

ManagementSupport

The router module is shipped with a comprehensive Management Information Base (MIB) for using Simple Network Management Protocol (SNMP), the industry standard for network management.

You can monitor and control the router module from any SNMP-based management station, including the 3Com Transcend Enterprise Manager.

In addition, the router module is fully compatible with CiscoWorks® network management software from Cisco Systems.

TELNET capability provides for direct access in-band to the agent, and a console port on the module provides for out-of-band management capability.

1-10 INTRODUCTION

Distributed, ScalableReliability

The router module operates in the CoreBuilder 5000 Integrated System Hub which is structured to eliminate any single point of failure.

The CoreBuilder 5000 hub provides redundancy for power supplies, switched ports, controller modules, and the hub management module. Automatic switching to the redundant components ensures continuation of the specific function.

3Com fault-tolerant features are fully-scalable, allowing you to implement and alter the degree of fault-tolerance you need as your network grows.

Hot Swap Capability The router module features “hot swap” capability. You can swap the router module in or out of (install or remove from) a powered-on CoreBuilder 5000 hub.

2
INSTALLING THE MODULE

■ Precautionary Procedures

■ Quick Installation

■ Unpacking Procedures

■ Preparing to Install the Router Module

■ Installing the Router Module

■ Making NIM Connections

Precautionary Procedures

CAUTION: Electrostatic discharge (ESD) can damage static-sensitive devices on circuit boards.

Follow these precautions when you unpack or handle the router module:

■ Do not remove the board from its antistatic shielding bag until you are ready to inspect or install it.

■ Handle the board by the faceplate only.

Use proper grounding techniques when you install the module, including:

■ Using a footstrap and grounded static mat or wearing a grounded static discharge wrist strap.

■ Touching the rack or other ground source just before you touch the module.

2-2 INSTALLING THE MODULE

Quick Installation Table 2-1 outlines the steps for quick installation of the CoreBuilder™ 5000 Network Router Module. If you are familiar with installing CoreBuilder 5000 modules, use this table as a checklist. Otherwise, refer to the remainder of this chapter and to Chapter 3 and Chapter 4 to complete the installation.

.

For information about potential installation problems, refer to the troubleshooting techniques described in Chapter 5, Troubleshooting.

Unpacking Procedures

To unpack the CoreBuilder 5000 Network Router Module:

1 Verify that the module is the model you ordered by checking the model number listed on the side of the shipping carton.

The product model number listed on the box contains the prefix “3C9.”

Table 2-1 Quick Installation Steps

Step Procedure Section Title/Page Number

1 Unpack the module. Unpacking Procedures on page 2-2

2 Prepare to install the module by setting DIP switches and verifying jumper plug positions.

Preparing to Install the Router Module on page 2-4

3 Install the module into three contiguous slots in the CoreBuilder 5000 Integrated System Hub.

Installing the Router Module on page 2-7

4 Connect the NIM cables. Making NIM Connections on page 2-8

5 Attach a terminal to the console or auxiliary ports.

Attaching a Management Terminal on page 3-2

6 Configure the NIM connections using Cisco IOS router configuration commands.

Configuring Cisco NIM Connections on page 3-3

7 Configure the Cisco router interfaces using Cisco IOS router configuration commands.

Configuring Cisco Parameters on page 3-3

8 Configure the Ethernet backplane connections using DMM software.

Configuring 3Com Parameters on page 3-8

9 Monitor initial router module operation. Monitoring Router Module LEDs on page 4-1

Unpacking Procedures 2-3

2 Remove the module, in its antistatic bag, from the shipping carton.

3 Remove the module from the antistatic shielding bag and inspect it for damage.

Always handle the module by the faceplate, being careful not to touch the components. If the module appears to be damaged, return it to the antistatic shielding bag, repack it in the shipping carton, and contact your local supplier.

Keep the shipping carton and the antistatic shielding bag in which your module was shipped so that you can repackage the module for storage or shipment.

4 Remove the spacing clips from the router module (Figure 2-1).

Figure 2-1 Locating the Spacing Clips

CAUTION: The spacing clips on the CoreBuilder 5000 Network Router Module are used only to protect the module during shipping. You must manually remove the spacing clips before you install the module.

Spacing clips


CAUTION: Failure to remove the spacing clips before installation could result in damage to the CoreBuilder 5000 Integrated System Hub.

Preparing to Install the Router Module

This section includes information to allow you to set module DIP switches and to correct jumper plug positions on the CPU board if the positions are inadvertently altered.

This section includes the following topics:

■ Setting DIP Switches

■ Verifying CPU Board Jumper Plug Positions

Setting DIP Switches Two configuration DIP switches are located on the base board of the router module (Figure 2-2).

Figure 2-2 Default Base Board DIP Switch Positions

ON ON

21 3 4 5 6 7 821 3 4 5 6 7 8 9 10

ON

21 3 4 5 6 7 821 3 4 5 6 7 8 9 10

ON

Ethernet backplane connections

Port 0 Port 1 Port 2 Port 3

Configuration source

Reserved

Backplane connectors

Base board

SW2SW1

Preparing to Install the Router Module 2-5

Use the configuration DIP switches to perform the following tasks:

■ Set the Configuration Source DIP Switch

■ Configure the Ethernet Backplane Connections

Setting the Configuration Source DIP Switch

Use the Configuration Source DIP switch (SW2-7) to identify the place from which the router module configures itself. Table 2-2 describes each Configuration Source DIP switch setting.

Configuring the Ethernet Backplane Connections

Assign each Ethernet port to one of the eight backplane networks or to isolated mode. Table 2-3 describes each Ethernet Backplane connection DIP switch setting (see Figure 2-2).

Table 2-2 Setting the Configuration Source for the Router Module

DIP SwitchSetting Configuration Source

ON NVRAM. Router module configured from last configuration stored in NVRAM on the router module.

OFF DIP switches. Router module configured from Ethernet backplane connection DIP switches.

Table 2-3 Configuring Backplane Connections for Ethernet Ports

Port DIP Switch Positions*

Backplane Connection

0 SW1-4 SW1-3 SW1-2 SW1-1

1 SW1-8 SW1-7 SW1-6 SW1-5

2 SW2-2 SW2-1 SW1-10 SW1-9

3 SW2-6 SW2-5 SW2-4 SW2-3

ON ON ON ON Isolated in Loopback mode

ON ON ON OFF Backplane network 1

ON ON OFF ON Backplane network 2

ON ON OFF OFF Backplane network 3

ON OFF ON ON Backplane network 4

ON OFF ON OFF Backplane network 5

ON OFF OFF ON Backplane network 6


The Ethernet backplane connection DIP switch settings are ignored by the router module if the Configuration Source DIP switch is set to ON.

* Unlisted DIP switch combinations default to Isolated in Loopback mode.

Verifying CPU BoardJumper Plug

Positions

Do not attempt to configure the jumper plugs on the CPU board. However, if you suspect that the jumper plug positions have been altered, restore them to the positions shown in Figure 2-3.

.

Figure 2-3 CPU Board Jumper Plug Positions

ON OFF OFF OFF Backplane network 7

OFF ON ON ON Backplane network 8

Table 2-3 Configuring Backplane Connections for Ethernet Ports (continued)

Port DIP Switch Positions*

Backplane Connection

0 SW1-4 SW1-3 SW1-2 SW1-1

1 SW1-8 SW1-7 SW1-6 SW1-5

2 SW2-2 SW2-1 SW1-10 SW1-9

3 SW2-6 SW2-5 SW2-4 SW2-3

Plugs not inserted

Plug inserted in bottom position Plug inserted

Installing the Router Module 2-7

Installing the Router Module

This section describes how to install the router module in the CoreBuilder 5000 Integrated System Hub.

You do not need to power down the hub to install or remove the router module. You can insert the module while the hub is operating (hot swap capability).

To install the router module:

1 Properly ground yourself prior to handling the module.

Put on a static wrist guard or touch a grounded static mat before you handle the module.

2 Locate 3 adjacent open slots in the hub, or remove panels on the hub to expose 3 slots for the router module.

3 Insert the router module into the board guides at the top and bottom of the slot and slide it into the hub by pressing firmly at the top and bottom of the faceplate. Make sure that the module ejectors are open fully when you insert the module and that the connectors are well-seated into the backplane of the hub. Figure 2-4 shows a router module being installed in a CoreBuilder 5000 Integrated System Hub.


Figure 2-4 CoreBuilder 5000 Network Router Module in a CoreBuilder 5000 Integrated System Hub

To minimize electromagnetic interference, ensure that the slots adjacent to the router module are occupied or have blank panels installed.

4 Push the module ejectors closed.

5 Using your fingers, tighten the spring-loaded screws on the front of the router module faceplate (do not overtighten).

Making NIM Connections

This section provides guidelines for making NIM (Network Interface Module) network cable connections. This section describes the following topics:

■ Making FDDI NIM Connections

■ Making Quad Serial NIM Connections

■ Making ATM NIM Connections

Spring-loaded screws

CoreBuilder 5000 NetworkRouter Module

Spring-loaded screws

Ejector (opened)

Ejector

Making NIM Connections 2-9

Making FDDI NIMConnections

This section provides information on the following topics:

■ Connecting the Multi-Mode, Dual Attachment Station NIM

■ Connecting the Multi-Mode, Single Attachment Station NIM

■ Connecting the Multi-Mode Optical Bypass Switch

■ Connecting the Single Mode, Dual Attachment Station NIM

Connecting the Multi-Mode, Dual Attachment Station NIM

The Multi-Mode, Dual Attachment Station NIM (MM, DAS) connectors are Fiber Distributed Data Interface (FDDI) standard physical sublayer (PHY) connectors. The media interface connector (MIC) connects to FDDI-standard 62.5/125 micron multi-mode fiber optic cable.

Figure 2-5 shows the MIC connector typically used for network and chassis connections in multi-mode FDDI applications.

Figure 2-5 Multi-Mode FDDI Network Interface Connector, MIC Type

A dual attachment station requires two connections, one to the primary ring and one to the secondary ring. On the FDDI MM, DAS NIM, the PHY-A port is the left port and PHY-B is the right port.

Figure 2-6 shows how to connect a FDDI MM, DAS router module to another Dual Attachment Station.

H17

38


Figure 2-6 Making Connections to the FDDI MM, DAS NIM

To connect the FDDI MM, DAS NIM to another Dual Attachment Station:

1 Connect PHY-A on the router module to PHY-B on the other DAS.

2 Connect PHY-B on the router module to PHY-A on the other DAS.

Connecting the Multi-Mode, Single Attachment Station NIM

Connect the Single Attachment router module’s PHY-A port through a concentrator to a Single Attachment ring (Figure 2-7).

Figure 2-7 Making Connections to the FDDI MM, SAS NIM

PHY-B

PHY-A

Dual Attachment Station (DAS)

PHY-BPHY-A

To concentrator

PHY-A


You can also connect the FDDI MM, SAS router module directly to another device in a point-to-point configuration.

Connecting the Multi-Mode Optical Bypass Switch

The Multi-Mode FDDI router modules provide an optical bypass capability that automatically drops the router module from the FDDI ring if the module fails. Dropping the module from the ring ensures that the ring remains available to the remaining stations.

Figure 2-8 Connecting the Multi-Mode Optical Bypass Switch

To connect the FDDI MM, DAS NIM (Figure 2-8) to an optical bypass switch (not included with the CoreBuilder 5000 Network Router Module):

1 Connect PHY-A on the router module to PHY-B on the optical bypass switch.

2 Connect PHY-B on the router module to PHY-A on the optical bypass switch.

3 Connect one end of the optical bypass interface cable to the 6-pin Deutsche Industrie-Norm (DIN) connector on the optical bypass switch.

4 Connect the other end of the optical bypass interface cable to the 6-pin DIN connector on the router module.

Connecting the Single Mode, Dual Attachment Station NIM

A dual attachment, single mode module configuration requires two connections, one to the primary ring and one to the secondary ring.

Optical bypass interface cable

Bypass operation

Optical bypass switch

DIN connector

To ring


Figure 2-9 shows how to connect a FDDI SM, DAS router module to another Dual Attachment Station.

Figure 2-9 Making Connections to the FDDI SM, DAS NIM

To connect the FDDI SM, DAS NIM to another Dual Attachment Station:

1 Connect one end of an FC connector cable to the PHY-A XMTR connector on the router module.

2 Connect the other end of the FC connector cable to the primary ring RCVR connector on the other DAS.

3 Connect one end of a second FC connector cable to the PHY-A RCVR connector on the router module.

4 Connect the other end of the second FC connector cable to the primary ring XMTR connector on the other DAS.

5 Connect one end of a third FC connector cable to the PHY-B XMTR connector on the router module.

6 Connect the other end of the third FC connector cable to the secondary ring RCVR connector on the other DAS.

7 Connect one end of a fourth FC connector cable to the PHY-B RCVR connector on the router module.

8 Connect the other end of the fourth FC connector cable to the secondary ring XMTR connector on the other DAS.

FC connector type

To primary ring

From primary ring

From secondary ring

To secondary ring


Making Quad SerialNIM Connections

The Quad Serial NIM has four synchronous serial ports with custom DB-60 connectors.

When setting up your serial port connections, consider distance limitations and potential electromagnetic interference (EMI) as defined in the Electronics Industries Association (EIA) and Telecommunications Industry Association (TIA) standards, such as standard EIA/TIA-232.

Figure 2-10 shows how to connect the Quad Serial NIM from any one serial port on the router module to a modem or other communications device.

Figure 2-10 Making Connections to the Quad Serial NIM

CAUTION: Be careful to insert the DB-60 connector correctly to prevent damage to the connector pins.

To connect the Quad Serial NIM, attach each serial port from the custom 60-pin connector to a modem or other DCE device using one of the following standard device cable connectors:

■ EIA/TIA-232

■ EIA/TIA-449

■ EIA-530

■ V.35

■ X.21

Modem or other communications device

EIA/TIA-232, EIA/TIA-449, V.35, X.21 or EIA-530 Connector

Custom 60-pin connectorSerial transmission cable


Making ATM NIMConnections

This section provides information on the following topics:

■ ATM Connector Types

■ ATM Distance Limitations

ATM Connector Types

Each ATM NIM type requires a specific connector (Figure 2-11):

OC-3 MM NIM – Requires a multi-mode SC-type connector.

OC-3 SM NIM – Requires a single mode SC-type connector.

Figure 2-11 Making Connections to the ATM NIMs

SC-type connector for ATM OC-3 MM NIM

SC-type connector forATM OC-3 SM NIM


ATM Distance Limitations

The SONET (Synchronous Optical Network) specification for fiber-optic transmission defines two types of fiber:

■ single mode

■ multimode

Single-mode fiber is capable of higher bandwidth and greater cable run distances than multimode fiber.

The typical maximum distances for single-mode and multimode transmissions, as defined by the SONET, are provided in Table 2-4. If you connect two optical devices at a distance greater than those specified in Table 2-4, significant signal loss could occur, making transmission unreliable.

Table 2-4 ATM Distance Limitations

Fiber Type Maximum Distance Between Stations

Single mode Up to 9 miles (15 kilometers)

Multimode Up to 1.5 miles (3 kilometers)

3
CONFIGURING THE MODULE

■ Configuration Overview

■ Attaching a Management Terminal

■ Configuring Cisco NIM Connections

■ Configuring Cisco Parameters

■ Configuring 3Com Parameters

CAUTION: Throughout this chapter, Cisco nomenclature refers to the four Ethernet backplane connections as interfaces 0, 1, 2, and 3. 3Com refers to the same four router connections as ports 1, 2, 3, and 4. For example, when configuring the router module, Cisco interface 0 is equivalent to 3Com port 1.

Configuration Overview

The following list is an overview of the procedures that are required to configure the router module. For more detail, refer to sections that follow.

CAUTION: Failure to follow the configuration sequence specified in this section could result in error messages at the router management terminal during the configuration procedure. For best results, use the procedure as outlined in the sections that follow.

To configure the router module:

1 Attach a Management Terminal – Attach a management terminal to the console port of the router module.

2 Configure Cisco NIM Connections – From the management terminal, use Cisco router configuration commands to configure the NIM (Network Interface Module) connections.

3-2 CONFIGURING THE MODULE

3 Configure Cisco Parameters – Use the management terminal to configure the four Cisco router interfaces.

4 Configure 3Com Parameters – Use the management terminal that is connected to the 3Com CoreBuilder™ 5000 Distributed (DMM) to configure the four 3Com router ports.

Each of these steps is detailed in the sections that follow.

If you are using the router module in an unmanaged hub (one in which a DMM module is not installed), upon power on, the router module uses the last module configuration saved in NVRAM. To enable NVRAM configuration, set DIP switch SW2-7 to On (see Figure 2-2).

When you power on the router module with NVRAM configuration disabled, the four Ethernet ports are set to isolated mode, or to what the DIP switch settings specify. Refer to Setting DIP Switches on page 2-4.

Attaching a Management Terminal

This section provides information on attaching a terminal to the console or auxiliary ports of the router module for use as a Cisco management terminal.

You must use the console port for initial router configuration. After you configure the router, you can use the auxiliary port for an asynchronous serial connection.

Connecting to theConsole Port

All router modules include an asynchronous router console port (female DB-25 connector) wired as a data communications equipment (DCE) device. The port requires a straight-through cable for connection to a local terminal. The port uses the following default parameters:

■ 9600 baud

■ 8 data bits

■ No parity generated or checked

■ 2 stop bits

Configuring Cisco NIM Connections 3-3

Connecting to theAuxiliary Port

All router modules include a male DB-25 connector auxiliary port (labeled AUX PORT DTE). The auxiliary port is a shared-memory data terminal equipment (DTE) port to which you can attach an EIA/TIA-232 connector from a channel service unit or data service unit (CSU or DSU), a modem, or protocol analyzer for network access.

Console and auxiliary port cabling requirements are provided in Appendix B, Cabling Specifications.

Configuring Cisco NIM Connections

From the Cisco management terminal, use Cisco IOS routing configuration commands to configure the FDDI or Quad Serial NIM connections.

If you are configuring a base router module without a NIM installed, proceed to the next section Configuring Cisco Parameters.

You may receive status messages referring to NIM 1, NIM 2, and NIM 3. Cisco IOS makes the following NIM designations:

■ Optional NIM as NIM 1

■ Ethernet backplane interfaces 0 and 1 (3Com ports 1 and 2) as NIM 2

■ Ethernet backplane interfaces 2 and 3 (3Com ports 3 and 4) as NIM 3

For detailed information on Cisco IOS routing configuration commands, refer to the Cisco hardcopy documentation set(Part Number 17-00138-MS) or to the Cisco documentation set on the Cisco UniverCD™ CD-ROM (Part Number 17-00138-CD).

Configuring Cisco Parameters

This section outlines procedures for configuring Cisco parameters for the four Ethernet interface connections on the router module using Cisco IOS software management commands. The procedures include:

■ Setting the Initial Router Module Configuration

■ Setting General Interface Parameters

■ Re-Starting the Interface Ports


Setting the InitialRouter Module

Configuration

When you first install the router module, you must define its basic configuration. Use the Cisco Setup utility to define the initial router module configuration.

To define the initial router module configuration:

1 Use DMM at the CoreBuilder 5000 management station to ensure that each router interface port is in Isolated mode. In the following example involving a module in slot 7, port 1 is set to Isolated mode:

CB5000> set port 7.1 network isolatedPort 07.01 network id set to ISOLATED.

2 At the router management terminal, set the terminal to enable mode:

Router> enable

3 Enter the required password:

Password: ****

4 At the router management terminal, set the terminal to Setup mode:

Router# setup

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.Refer to the 'Getting Started' Guide for additional help.Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brackets '[]'.

Continue with configuration dialog? [yes]:

5 Enter Yes to continue.

6 Follow the prompts in the Setup program to configure the Cisco interface parameters. Refer to Cisco Setup documentation for detailed information on the Setup utility.

An example of a typical configuration transcript follows.

First, would you like to see the current interface summary? [yes]: yes

Interface IP-Address OK? Method Status ProtocolEthernet0 0.0.0.0 NO NVRAM down down

Configuring Cisco Parameters 3-5

Ethernet1 0.0.0.0 NO NVRAM down downEthernet2 0.0.0.0 NO NVRAM down downEthernet3 0.0.0.0 NO NVRAM down downFDDI0 0.0.0.0 NO NVRAM down downFDDI1 0.0.0.0 NO NVRAM down down

Configuring global parameters:

Enter host name [Router]:

The enable secret is a one-way cryptographic secret used instead of the enable password when it exists.

Enter enable secret [<Use current secret>]:

The enable password is used when there is no enable secret and when using older software and some boot images.

Enter enable password [denise]:Enter virtual terminal password [lab]:Configure SNMP Network Management? [yes]:Community string [public]:Configure IP? [yes]:Configure IGRP routing? [yes]:Your IGRP autonomous system number [1]:

Configuring interface parameters:

Configuring interface Ethernet0:Is this interface in use? [no]: yesConfigure IP on this interface? [yes]:IP address for this interface [0.0.0.0]: 151.104.15.19Number of bits in subnet field [0]: 8Class B network is 151.104.0.0, 8 subnet bits; mask is 255.255.255.0


Configuring interface Ethernet2:Is this interface in use? [no]: yes


Configure IP on this interface? [yes]:IP address for this interface [0.0.0.0]: 151.104.17.18Number of bits in subnet field [0]: 8Class B network is 151.104.0.0, 8 subnet bits; mask is 255.255.255.0


The following configuration command script was created:

hostname Routerenable secret 5 $1$S4Kx$sqhp90V6Gk7WDxEXYy.on1enable password deniseline vty 0 4password labsnmp-server community public!ip routing!interface Ethernet0ip address 151.104.15.19 255.255.255.0!interface Ethernet1ip address 151.104.16.18 255.255.255.0!interface Ethernet2ip address 151.104.17.18 255.255.255.0!interface Ethernet3ip address 151.104.18.18 255.255.255.0!router igrp 1network 151.104.0.0!end

Use this configuration? [yes/no]: yesBuilding configuration...[OK]

Configuring Cisco Parameters 3-7

Use the enabled mode 'configure' command to modify this configuration.

Router#Router# write memBuilding configuration...[OK]Router#

Setting GeneralInterface Parameters

Set any required general Cisco parameters for the four router interfaces. Cisco Systems IOS software provides management commands for configuring routing interface connections. Refer to the Cisco hardcopy documentation set (Part Number 17-00138-MS) or to the Cisco documentation set on the Cisco UniverCD CD-ROM(Part Number 17-00138-CD).

Re-Starting theInterface Ports

When you have finished configuring general interface parameters, remove each interface port from the Shutdown state using the following procedure:

1 Select the Configuration mode.

Router # config termRouter (config)#

2 Select the port to be re-started. In this example, Ethernet interface port e0 is re-started.

Router (config)# int e0Router (config)#

3 Issue the No Shut command for the port.

Router (config)# no shutRouter (config)#

4 Repeat steps 2 and 3 for each interface port.

5 Press Ctrl-Z to exit from the Configuration mode.


Configuring 3Com Parameters

This section outlines procedures for using DMM commands to configure basic parameters for the 3Com router module.

Refer to the 3Com CoreBuilder 5000 Integrated System Hub Installation and Operation Guide, Chapter 1, for a CoreBuilder 5000 backplane architecture description and to the 3Com DMM Commands Guide for detailed information on DMM configuration commands.

To configure the 3Com router module:

1 Connect each of the router ports to one of the 8 CoreBuilder 5000 backplane networks (or set the port to isolated mode).

In the following example, 3Com router port 1 (Cisco interface 0) is set to backplane network 7:

CB5000> set port 7.1 network ethernet_7Port 07.01 network id set to ETHERNET_7.

2 Save the configuration:

CB5000> save all

Failure to save configuration settings may result in loss of configuration data.

You can use DMM SHOW commands to display some configured parameters for the module. Refer to Displaying the Router Module Configuration on page 4-10 for more information.

4
MONITORING OPERATION

■ Monitoring Router Module LEDs

■ Displaying the Router Module Configuration

Monitoring Router Module LEDs

This section identifies the front panel LEDs of the CoreBuilder™ 5000 Network Router Module:

■ Common Front Panel LEDs

■ FDDI NIM LEDs

■ Quad Serial NIM LEDs

■ ATM NIM LEDs

Common Front PanelLEDs

The front panel LEDs of the base model (without NIM) router module are common to all router module models. Figure 4-1 shows the common front panel LEDs. Table 4-1 describes the LEDs.

4-2 MONITORING OPERATION

Figure 4-1 Common Front Panel LEDs

RESET is a recessed pushbutton that is used to reset the router module under certain conditions. Refer to Chapter 5, Troubleshooting, for more information on using the RESET button.

MOD STATUSRESETSWITCH

SYS RUN

LEDS

P3

P0

NIM

DENA,B

STATUSP1

P2

P3

P0

P1

P2

ACT

DENC,D

HLTH

NIM

DENA,B

DENC,D

NIM PRES

Monitoring Router Module LEDs 4-3

.

Table 4-1 Front Panel LED Definitions

LED Description Definition

MOD STATUS Module Status Indicates the status of the module connectivity to the CoreBuilder 5000 backplane.

ON – Indicates that the router module is able to connect to the backplane.

Blinking indicates that 3Com router software failed startup diagnostics and the router module is unable to connect to the CoreBuilder 5000 backplane.

OFF – Indicates that 3Com router software is not operational and the router module is unable to connect to the CoreBuilder 5000 backplane.

NIM PRES NIM Present ON – Indicates that an optional NIM is installed on the router module.

OFF – Indicates that an optional NIM is not installed on the router module.

SYS RUN System Run ON – Indicates that Cisco IOS router software is loaded and operational.

OFF – Indicates that Cisco IOS router software is not loaded and operational.

LEDS NIM NIM 1 Data Present

ON – Indicates that data traffic is present on one or more of the interfaces on the optional NIM.

OFF – Indicates that data traffic is not present on any interfaces on the optional NIM.

LEDS DEN A, B NIM 2 (Dual Ethernet A and B) Data Present

ON – Indicates that data traffic is present on one or both of Cisco interfaces 0 and 1 (3Com ports 1 and 2).

OFF – Indicates that data traffic is not present on Cisco interfaces 0 and 1 (3Com ports 1 and 2).

LEDS DEN C, D NIM 3 (Dual Ethernet C and D) Data Present

ON – Indicates that data traffic is present on one or both of Cisco interfaces 2 and 3 (3Com ports 3 and 4).

OFF – Indicates that data traffic is not present on Cisco interfaces 2 and 3 (3Com ports 3 and 4).


HLTH NIM NIM 1 Healthy ON – Indicates that optional NIM 1 is operational and line protocol for the NIM interfaces is functional.

OFF – Indicates that the optional NIM 1 is not operational or that line protocol for the NIM is not functional.

HLTH DEN A, B NIM 2 (Dual Ethernet A and B) Healthy

ON – Indicates that Cisco interfaces 0 and 1 (3Com ports 1 and 2) are operational and line protocol for the interfaces is functional.

OFF – Indicates that Cisco interfaces 0 and 1 (3Com ports 1 and 2) are not operational or that line protocol for the NIM is not functional.

HLTH DEN C, D NIM 3 (Dual Ethernet C and D) Healthy

ON – Indicates that Cisco interfaces 2 and 3 (3Com ports 3 and 4) are operational and line protocol for the interfaces is functional.

OFF – Indicates that Cisco interfaces 2 and 3 (3Com ports 3 and 4) are not operational or that line protocol for the NIM is not functional.

P0 ACT Port 1 (Cisco interface 0) active

ON – Indicates that data traffic is present on port 1 (Cisco interface 0).

OFF – Indicates that data traffic is not present on port 1 (Cisco interface 0).










Table 4-1 Front Panel LED Definitions (continued)



P0 STATUS Port 1 (Cisco interface 0) Status

ON – Indicates that port 1 (Cisco interface 0) is connected to its assigned backplane network.

OFF – Indicates that port 1(Cisco interface 0) is not connected to its assigned backplane network, or is set to Isolated mode (in loopback).



OFF – Indicates that port 2 (Cisco interface 1) is not connected to its assigned backplane network, or is set to Isolated mode (in loopback).







Table 4-1 Front Panel LED Definitions (continued)



FDDI NIM LEDs In addition to the common front panel LEDs, the three FDDI router module models are also equipped with the FDDI LEDs shown in Figure 4-2.

Figure 4-2 FDDI NIM LEDs

The PHY-A RING OP LED lights when the router module PHY-A attachment is connected in the FDDI A ring. The PHY-B RING OP LED (Dual-Attachment FDDI NIMs only) lights when the PHY-B attachment is connected in the FDDI B ring.

PHY-ARING OP

PHY-BRING OP

FDDI MM, DAS Router Module

FDDI MM, SAS Router Module

FDDI SM, DAS Router Module


Quad Serial NIMLEDs

The Quad Serial NIM router module includes the additional LEDs shown in Figure 4-3.

Figure 4-3 Quad Serial NIM LEDs

P-3

P-2

P-1

P-0

LPCNTDTCRDRC

LPCNTDTCRDRC

LPCNTDTCRDRC

LPCNTDTCRDRC


Table 4-2 describes the Quad Serial NIM LEDs.

Table 4-2 Quad Serial NIM LED Definitions


LP Looped ON – Indicates that the port is set to a Loopback state.

OFF – Indicates that the port is set to Normal mode.

CN Connected ON – Indicates that the port is in Ready-state (DSR, DTR, DCD, RTS, CTS signals) to exchange data.

OFF – Indicates that the port is not in Ready-state to exchange data.

TD Transmitted Data ON – Indicates that data is being transmitted over the serial link from the DTE device. You can set the router module port to operate as DTE or DCE.

OFF – Indicates that data is not being transmitted by the DTE device.

TC Transmitted Clock The clock supplied by the DCE device to synchronize transmitted data.

RD Received Data ON – Indicates that data is being received over the serial link by the DCE device. You can set the router port to operate as DTE or DCE.

OFF – Indicates that data is not being received by the DCE device.

RC Received Clock The clock supplied by the DCE device to synchronize received data.


ATM NIM LEDs The ATM MM and ATM SM router modules include the additional LEDs shown in Figure 4-4.

Figure 4-4 ATM NIM LEDs


Table 4-3 describes the ATM NIM LEDs.

Displaying the Router Module Configuration

To display information about router module configuration and status, use the following DMM commands.

■ SHOW MODULE

■ SHOW MODULE VERBOSE

■ SHOW PORT

■ SHOW PORT VERBOSE

Using the SHOWMODULE Command

Use the SHOW MODULE command to display summary information about the router module:

CB5000> show module 2.1

Table 4-3 ATM NIM LED Definitions


Busy ATM NIM Busy ON – Indicates that the NIM is not available to receive data cells.

OFF – Indicates that the NIM is available for data cells.

Ready ATM NIM Ready ON – Indicates that the NIM is not available to receive data cells.

OFF – Indicates that the NIM is not ready to receive ATM cells.

RX Cells Received Cells ON – Indicates that the ATM NIM is receiving a a data cell. This LED flickers during normal operation.

OFF – Indicates that the ATM NIM is not receiving a data cell.

Rx Alarm Receive Alarm ON – Indicates that the receive signal is lost or that a remote alarm has been received by the ATM NIM.

OFF – Indicates that the receive signal is not lost and that a remote alarm has not been received.

Displaying the Router Module Configuration 4-11

This command displays the summary information shown in Figure 4-5.

Figure 4-5 SHOW MODULE Command Information

Using the SHOWMODULE VERBOSE

Command

Use the SHOW MODULE VERBOSE command to display detailed information about the router module:

CB5000> show module 2.1 verbose

This command displays the detailed information shown in Figure 4-6.

Figure 4-6 SHOW MODULE VERBOSE Command Information

Using the SHOWPORT Command

Use the SHOW PORT command to display summary information about any of the four router module ports:

CB5000> show port 2.1

This command displays the summary information shown in Figure 4-7.

Figure 4-7 SHOW PORT Command Information

Slot Module Version Network General Information----- --------------- ------- ------------- -------------------02.01 6704R-ECS V1.00.0 PER_PORT Module up

Slot Module Version Network General Information----- --------------- ------- ------------- -------------------02.01 6704R-ECS V1.00.0 PER_PORT Module up

6704R-ECS: CB5000 Ethernet Backbone Router Module

Boot Version: V1.00.0Non-Volatile DIP Setting: ENABLEDNative Software Version: x10.30Native Boot Software Version: v5.10Number Simple Ports: 1Network Interface Module Type: FDDI-SINGLE-MODE-DUAL-ATTACH

Port Mode Status Network General Information----- -------- ------------------- ---------------- ---------------------02.01 LOGICAL OKAY ETHERNET_1


Using the SHOWPORT VERBOSE

Command

Use the SHOW PORT VERBOSE command to display detailed information about any one of the four router module ports:

CB5000> show port 2.1 verbose

This command displays the detailed information shown in Figure 4-8.

Figure 4-8 SHOW PORT VERBOSE Command Information

The Speed field in Figure 4-8 identifies the speed for the Cisco interface that corresponds to the 3Com port.

Port Display for Module 6704R-ECS:

Port Mode Status Network General Information----- -------- ------------------- ---------------- ----------------------02.01 LOGICAL OKAY ETHERNET_1

Port Connector: BACKPLANEIP Address: 151.104.15.19Subnetwork Mask: ff.ff.ff.00Default Gateway: 151.104.15.19Station Address: 08-00-00-00-00-03Speed: 10 MBPS

5
TROUBLESHOOTING
This chapter provides hardware troubleshooting information to use if the CoreBuilder™ 5000 Network Router Module fails to operate correctly. After reviewing the information in this chapter, if you cannot correct the problem, contact your 3Com representative for further assistance.

For IOS software-related troubleshooting information, refer to the appropriate Cisco Systems manual or refer to Cisco information on the World Wide Web at http://www.cisco.com/. For information on interpreting router module LEDs, refer to Chapter 4, Monitoring Operation.


■ Troubleshooting Startup Problems

■ Troubleshooting Network Connection Problems

■ Troubleshooting WAN Connection Problems

■ Correcting Operating Malfunctions

■ Recovering a Lost Password

Troubleshooting Startup Problems

This section describes how to troubleshoot startup problems on the CoreBuilder 5000 Network Router Module.

When you first install the router module in the hub, the Cisco Systems router software runs a set of hardware diagnostic tests. If the router module fails diagnostics, the MOD STATUS LED blinks and the SYS RUN LED does not light. This indicates a problem with the router module hardware or software. Refer to Table 4-1 on page 4-3 for more information on router module LED indications. Refer to the appropriate Cisco Systems troubleshooting documentation for corrective action.

5-2 TROUBLESHOOTING

Troubleshooting Network Connection Problems

If the CoreBuilder 5000 Network Router Module does not appear to be routing traffic properly on the network, it may indicate that there is no connection to the network. Perform the following troubleshooting actions:

■ From the 3Com management interface (for example, CoreBuilder 5000 Distributed Management Module), verify that the router module backplane port is set to the appropriate backplane network (channel).

■ Use the DMM SHOW PORT command and check the Status field for the port. Refer to Using the SHOW PORT VERBOSE Command on page 4-12.

■ Use the ping utility to confirm there is network connectivity.

■ Verify that your router configuration is valid. Refer to the Cisco Systems Troubleshooting Internetworking Systems guide for more information.

Troubleshooting WAN Connection Problems

If you suspect that the CoreBuilder 5000 Network Router Module has lost WAN connectivity, perform the following troubleshooting actions:

■ Verify that you have the correct cable for your configuration. Refer to Appendix B, Cabling Specifications, for lists of approved cables, cable specifications, and pinouts.

■ If you are using a:

DCE cable – Verify that a clock rate is defined in the router WAN interface configuration.

DTE cable – Verify that no clock rate is defined in the router WAN interface configuration.

■ Verify that your router configuration is valid. Refer to the Cisco Systems Troubleshooting Internetworking Systems guide for more information.

Correcting Operating Malfunctions 5-3

Correcting Operating Malfunctions

Table 5-1 lists the symptoms, possible causes, and corrective actions of operating malfunctions for the CoreBuilder 5000 Network Router Module.

.

Table 5-1 Troubleshooting Malfunctions

Symptom Possible Cause Corrective Action

Module does not power up Module is not fitted correctly against backplane.

To ensure that the module is fitted correctly, remove the module from the slots and replace it in the slots.

Place the module in different slots in the hub.

Power mode is not enabled for slot.

Ensure that power mode is enabled for the slot.

The hub is not receiving electrical power.

Check that the hub is receiving power.

Test for power at the wall outlet by plugging in another device.

If the wall outlet is not receiving power, select another outlet on a different circuit.

Attached terminal does not operate

The terminal is malfunctioning.

Follow the troubleshooting procedures recommended by the terminal manufacturer.

Cables are unattached. Make sure that the cable connections at both ends are secure.

Cables are not the correct type.

Make sure that the cable attached to the terminal conforms to the specification. Refer to Appendix B for cabling specifications.

The console is configured incorrectly.

Check the console port configuration.Note: You can use TELNET to verify port configurations.

Refer to the Cisco Systems Router Products Configuration and Reference documents for more information. Verify that the port is configured as:

■ 8-bit data

■ No parity

■ 2 stop bits

■ 9600 baud rate

■ Flow control parameters set to Xon and Xoff

5-4 TROUBLESHOOTING

Recovering a Lost Password

To recover a lost password:

1 Attach an ASCII terminal to the router module console port.

2 Configure the terminal to operate at 9600 baud, 8 data bits, no parity, 2 stop bits.

3 Enter the SHOW VERSION command to display the existing configuration register value. Note this value for later use in step 13.

4 If the Break function is disabled on the router (refer to Table C-1), power cycle the router (turn off the router, wait 5 seconds, and then turn it on again). If the Break function is enabled, go to step 5.

5 Within 60 seconds of turning on the router, press the Break key. Pressing this key causes the terminal to display the bootstrap program prompt (>).

6 To reset the virtual configuration register (VCR) to boot from the boot ROMs and ignore NVRAM, enter the O/R (Reset VCR Value) command at the bootstrap prompt:

> o/r 0x2141

To recover a lost password, you must be able to see it when you display configuration information. To see the password, be sure to set the configuration register so that the router module engine ignores the contents of the NVRAM.

The terminal fails to respond to commands entered at the keyboard

The terminal is not receiving commands.

Power off the terminal, wait 30 seconds, and then power on again.

The keyboard cable is attached incorrectly.

If the terminal still does not respond to commands, power off the terminal and disconnect the keyboard cable. Then re-attach the keyboard cable and power on the terminal.

Cables are not the correct type.

Make sure that the cable attached to the terminal conforms to the specification. Refer to Appendix B for cabling specifications.

The console port is malfunctioning.

Check the state of the LEDs on the front of the module. If the LEDs indicate a problem, contact your supplier for assistance.

Table 5-1 Troubleshooting Malfunctions (continued)

Symptom Possible Cause Corrective Action

Recovering a Lost Password 5-5

7 Initialize the router by entering the I (Initialize) command as follows:

> i

The router power cycles and the configuration register is set to 0x2141 (ignore Break key, ignore NVRAM, boot from ROM). The router boots the boot ROM system image and prompts you with the following system configuration dialog prompt:

--- System Configuration Dialog ---

8 Enter No in response to the system configuration dialog prompts until the following system message appears:

Press RETURN to get started!

9 Press Return. The boot ROM prompt appears as follows:

Router(boot)>

10 Enter the ENABLE command to enter the EXEC mode in the boot ROM image. The prompt changes to the following:

Router(boot)#

11 Enter the SHOW CONFIGURATION EXEC command to display the password in the configuration file and to display any boot system commands.

12 To exit configuration mode, press Ctrl-Z.

13 Restore the virtual configuration register to the value noted in step 3. Use the CONFIGURE TERMINAL command to restore the value:

router# configure terminalEnter system configuration commands, one per line.

Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Zconfig-reg 0xYYYY^Zwhere YYYY is the value noted in step 3

14 Reboot the router and use the recovered password.

Refer to Appendix C for more information about the virtual configuration register.

A
PRODUCT SPECIFICATIONS
This appendix contains the following hardware specifications for the 3Com CoreBuilder™ 5000 Network Router Module:

■ General Specifications

■ Electrical Specifications

■ Environmental Specifications

■ Mechanical Specifications

A-2 PRODUCT SPECIFICATIONS

General Specifications

Table A-1 identifies general specifications for the router module.

* The Orion microprocessor is based on the MIPS R4400 and is pin-compatible.† NRZ = Nonreturn to zero. NRZI = Nonreturn to zero inverted.‡ DTE = Data terminal equipment. DCE = Data communications equipment.

Table A-1 General Router Module Specifications

Specification Description

Processor 100 MHz IDT Orion RISC*

Main Memory (DRAM) 8, 16, or 32 MB

Shared Memory (DRAM) 4, 8, or 16 MB

Flash Memory 4, 8 MB

Nonvolatile RAM 128 or 512 KB

Boot ROM 128 to 512 KB

Boot Flash 4 MB

Network Interface Options

FDDI Multi-Mode, Dual Attachment Station FDDI Multi-Mode, Single Attachment StationFDDI Single Mode, Dual Attachment StationQuad SerialATM OC3, Multi-ModeATM OC3, Single Mode

Ethernet Interface 4 backplane connection

Synchronous Serial Interfaces(Quad Serial NIM)

EIA/TIA-232, EIA/TIA-449, V.35, X.21 (NRZ/NRZI† and DTE/DCE‡), EIA-530 (NRZ/NRZI and DTE). All serial cables use a DB-60 connector.

Console and Auxiliary Ports

Asynchronous serial

Electrical Specifications A-3

Electrical Specifications

Table A-2 identifies the electrical specifications for the router module.

Environmental Specifications

Table A-3 identifies environmental specifications for the router module.

Mechanical Specifications

Table A-4 identifies the mechanical specifications of the router module.

Table A-2 Electrical Router Module Specifications

Voltage Amps (Watts)

Power Requirements(with NIM)

+5 VDC 19.0 A (95.0 W)

–5 VDC 0.20 A (1.00 W)

+12 VDC 0.5 A (6.0 W)

–12 VDC 0.08 A (1.0 W)

–2 VDC 0.05A (0.1 W)

(103.1 W Total)

Table A-3 Environmental Router Module Specifications

Operating Temperature 0 °C to 50 °C (32 °F to 122 °F)

Storage Temperature -10 °C to 66 °C (22 °F to 138 °F)

Humidity Less than 95%, noncondensing

BTU/hr 349.31 BTUs/hr

Table A-4 Mechanical Router Module Specifications

CoreBuilder 5000Network Router Module(with NIM)

Width 3.0” (7.62 cm)

Length 10.875” (27.623 cm)

Height 15.250” (38.735 cm)

Weight 8.5 lbs (3.859 kg)

B
CABLING SPECIFICATIONS
Use the information in this appendix to verify that the cables you use meet equipment requirements. For proper operation, use only approved cables when you install all equipment.

This appendix describes:

■ Console and Auxiliary Port Cables

■ Quad Serial NIM Cables

Console and Auxiliary Port Cables

This section specifies the cable pinouts of the console and auxiliary ports of the CoreBuilder™ 5000 Network Router Module. You can use any cable that meets the pinout specifications described in this section.

All pins not listed are not connected.

This section describes the following cabling specifications:

■ Console Port Pinouts

■ Auxiliary Port Pinouts

B-2 CABLING SPECIFICATIONS

Console Port Pinouts Table B-1 identifies the pinout specifications for the console port.

Auxiliary PortPinouts

Table B-2 identifies the pinout specifications for the auxiliary port.

Table B-1 Console Port Pinout Specification

Pin Signal Name Input/Output

1 Frame GND —

2 Received Data Input

3 Transmitted Data Output

4 Request To Send Looped to Clear To Send

5 Clear To Send Looped to Request To Send

6 Connected to Pin 8 Output

7 Signal Ground —

8 Data Carrier Detect Output

20 Data Terminal Ready Input

Table B-2 Auxiliary Port Pinout Specification

Pin Signal Name Input/Output

1 Frame GND —

2 Transmitted Data Output

3 Received Data Input

4 Request To Send Output

5 Clear To Send Input

7 Signal Ground —

8 Data Carrier Detect Input

20 Data Terminal Ready Output

Quad Serial NIM Cables B-3

Quad Serial NIM Cables

This section specifies cable pinouts for each type of synchronous serial cable supported by the Quad Serial NIM (Network Interface Module) on the CoreBuilder 5000 Network Router Module.

This section describes:

■ EIA-530 Cable Pinout Specifications

■ EIA-232 DTE Cable Pinouts (DB-60 to DB-25)

■ EIA-232 DCE Cable Pinouts (DB-60 to DB-25)

■ EIA-449 DTE Cable Pinouts (DB-60 to DB-37)

■ EIA-449 DCE Cable Pinouts (DB-60 to DB-37)

■ V.35 DTE Cable Pinouts (DB-60 to Winchester-Type 34-Pin)

■ V.35 DCE Cable Pinouts (DB-60 to Winchester-Type 34-Pin)

■ X.21 DTE Cable Pinouts (DB-60 to DB-15)

■ X.21 DCE Cable Pinouts (DB-60 to DB-15)

In Table B-3 through Table B-11, serial pinouts for DTE and DCE cables use arrows to indicate signal direction:

■ → indicates DTE to DCE

■ ← indicates DCE to DTE

Due to the small pins on the DB-60 connector, you should not attempt to manufacture or solder these cables.


EIA-530 DTESynchronous Serial

Cable Pinouts

Figure B-1 shows the EIA-530 serial cable assembly and Table B-3 lists the cable pinouts (Part Number ERM530-CAB). Arrows in the table indicate signal direction:



Figure B-1 EIA-530 Cable Assembly

H19

72

60-pin connector 25-pin connector

Connectors are not to scale

J2-13J2-25

J2-14J2-1

J1-46J1-45J1-16J1-15

J1-1J1-30J1-31J1-60


Table B-3 EIA-530 Cable Pinout Specifications

60 Pin1 Signal 25 Pin1 SignalDirection DTE DCE2

J1-46J1-47

Shield_GNDMODE_2

J2-1—

Shield—

Shorted

J1-48J1-49

GNDMODE_1

— — Shorted

J1-11J1-12

TxD/RxD+TxD/RxD-

J2-2J2-14

BA(A), TxD+BA(B), TxD-

→→

J1-28J1-27

RxD/TxD+RxD/TxD-

J2-3J2-16

BB(A), RxD+BB(B), RxD-

←←

J1-9J1-10

RTS/CTS+RTS/CTS-

J2-4J2-19

CA(A), RTS+CA(B), RTS-

→→

J1-1J1-2

CTS/RTS+CTS/RTS-

J2-5J2-13

CB(A), CTS+CB(B), CTS-

←←

J1-3J1-4

DSR/DTR+DSR/DTR-

J2-6J2-22

CC(A), DSR+CC(B), DSR-

←←

J1-5J1-6

DCD/DCD+DCD/DCD-

J2-8J2-10

CF(A), DCD+CF(B), DCD-

←←

J1-24J1-23

TxC/RxC+TxC/RxC-

J2-15J2-12

DB(A), TxC+DB(B), TxC-

←←

J1-26J1-25

RxC/TxCE+RxC/TxCE-

J2-17J2-9

DD(A), RxC+DD(B), RxC-

←←

J1-44J1-45

LL/DCDCircuit_GND

J2-18J2-7

LLCircuit GND

→—

J1-7J1-8

DTR/DSR+DTR/DSR-

J2-20J2-23

CD(A), DTR+CD(B), DTR-

→→

J1-13J1-14

TxCE/TxC+TxCE/TxC-

J2-24J2-11

DA(A), TxCE+DA(B), TxCE-

→→

J1-51J1-52

GNDMODE_DCE

— — Shorted

1Any pin not referenced is not connected.2 The EIA-530 interface cannot be operated in DCE mode. A DCE cable is not

available for the EIA-530 interface.


EIA-232 DTE andDCE Serial Cable

Assembly andPinouts (DB-25)

Figure B-2 shows the EIA-232 serial cable assembly. Table B-4 lists the DTE cable pinouts (Part Number ERM232-CAB). Table B-5 lists the DCE cable pinouts (Part Number ERF232-CAB). Arrows in the tables indicate signal direction:



Figure B-2 EIA-232 Serial Cable Assembly

H19

72

60-pin connector 25-pin connector


J2-13J2-25

J2-14J2-1

J1-46J1-45J1-16J1-15

J1-1J1-30J1-31J1-60


Table B-4 EIA-232 DTE Cable Pinouts (DB-60 to DB-25)

60 Pin1 Signal Note Direction 25 Pin1 Signal

J1-50J1-51J1-52

MODE_0GNDMODE_DCE

Shorting Group — — —

J1-46 Shield_GND Single — J2-1 Shield GND

J1-41Shield

TxD/RxD—

Twisted pair no. 5 →—

J2-2Shield

TxD—

J1-36Shield

RxD/TxD—

Twisted pair no. 9 ←—

J2-3Shield

RxD—

J1-42Shield

RTS/CTS—


J2-4Shield

RTS—

J1-35Shield

CTS/RTS—


J2-5Shield

CTS—

J1-34Shield

DSR/DTR—


J2-6Shield

DSR—

J1-45Shield

Circuit GND Twisted pair no. 1 — J2-7Shield

Circuit GND

J1-33Shield

DCD/LL—


J2-8Shield

DCD—

J1-37Shield

TxC/NIL—


J2-15Shield

TxC—

J1-38Shield

RxC/TxCE—


J2-17Shield

RxC—

J1-44Shield

LL/DCD—


J2-18Shield

LTST—

J1-43Shield

DTR/DSR—


J2-20Shield

DTR—

J1-39Shield

TxCE/TxC—


J2-24Shield

TxCE—

1 Any pin not referenced is not connected.


Table B-5 EIA-232 DCE Cable Pinouts (DB-60 to DB-25)


J1-50J1-51

MODE_0GND



J1-36Shield

RxD/TxD—


J2-2Shield

TxD—

J1-41Shield

TxD/RxD—


J2-3Shield

RxD—

J1-35Shield

CTS/RTS—


J2-4Shield

RTS—

J1-42Shield

RTS/CTS—


J2-5Shield

CTS—

J1-43Shield

DTR/DSR—


J2-6Shield

DSR—

J1-45Shield

Circuit GND—

Twisted pair no. 1 ——

J2-7Shield

Circuit GND

J1-44Shield

LL/DCD—


J2-8Shield

DCD—

J1-39Shield

TxCE/TxC—


J2-15Shield

TxC—

J1-40Shield

NIL/RxC—


J2-17Shield

RxC—

J1-33Shield

DCD/LL—


J2-18Shield

LTST—

J1-34Shield

DSR/DTR—


J2-20Shield

DTR—

J1-38Shield

RxC/TxCE—


J2-24Shield

TxCE—



EIA-449 DTE andDCE Serial Cable

Assembly andPinouts (DB-37)

Figure B-3 shows the EIA-449 serial cable assembly. Table B-6 lists the DTE cable pinouts (Part Number ERM449-CAB). Table B-7 lists the DCE cable pinouts (Part Number ERF449-CAB). Arrows in the tables indicate signal direction:



Figure B-3 EIA-449 Serial Cable Assembly

H19

73

60-pin connector (J1) 37-pin connector (J2)


J2-19J2-37

J2-20J2-1

J1-46J1-45J1-16J1-15

J1-1J1-30J1-31J1-60


Table B-6 EIA-449 DTE Cable Pinouts (DB-60 to DB-37)


J1-49J1-48

MODE_1GND


J1-51J1-52

GNDMODE_DCE



J1-11J1-12

TxD/RxD+TxD/RxD-

Twisted pair no. 6 →→

J2-4J2-22

SD+SD—

J1-24J1-23

TxC/RxC+TxC/RxC-

Twisted pair no. 9 ←←

J2-5J2-23

ST+ST-

J1-28J1-27

RxD/TxD+RxD/TxD-


J2-6J2-24

RD+RD-

J1-9J1-10

RTS/CTS+RTS/CTS-


J2-7J2-25

RS+RS-

J1-26J1-25

RxC/TxCE+RxC/TxCE-


J2-8J2-26

RT+RT-

J1-1J1-2

CTS/RTS+CTS/RTS-


J2-9J2-27

CS+CS-

J1-44J1-45

LL/DCDCircuit_GND


J2-10J2-37

LLSC

J1-3J1-4

DSR/DTR+DSR/DTR-


J2-11J2-29

DM+DM-

J1-7J1-8

DTR/DSR+DTR/DSR-


J2-12J2-30

TR+TR-

J1-5J1-6

DCD/DCD+DCD/DCD-


J2-13J2-31

RR+RR-

J1-13J1-14

TxCE/TxC+TxCE/TxC-


J2-17J2-35

TT+TT-

J1-15J1-16

Circuit_GNDCircuit_GND


J2-19J2-20

SGRC



Table B-7 EIA-449 DCE Cable Pinouts (DB-60 to DB-37)


J1-49J1-48

MODE_1GND

Shorting group — — —


J1-28J1-27

RxD/TxD+RxD/TxD-


J2-4J2-22

SD+SD-

J1-13J1-14

TxCE/TxC+TxCE/TxC-


J2-5J2-23

ST+ST-

J1-11J1-12

TxD/RxD+TxD/RxD-


J2-6J2-24

RD+RD-

J1-1J1-2

CTS/RTS+CTS/RTS-


J2-7J2-25

RS+RS-

J1-24J1-23

TxC/RxC+TxC/RxC-


J2-8J2-26

RT+RT-

J1-9J1-10

RTS/CTS+RTS/CTS-


J2-9J2-27

CS+CS-

J1-29J1-30

NIL/LLCircuit_GND


J2-10J2-37

LLSC

J1-7J1-8

DTR/DSR+DTR/DSR-


J2-11J2-29

DM+DM-

J1-3J1-4

DSR/DTR+DSR/DTR-


J2-12J2-30

TR+TR-

J1-5J1-6

DCD/DCD+DCD/DCD-


J2-13J2-31

RR+RR-

J1-26J1-25

RxC/TxCE+RxC/TxCE-


J2-17J2-35

TT+TT-

J1-15J1-16

Circuit_GNDCircuit_GND

Twisted pair no. 8 — J2-19J2-20

SGRC



V.35 DTE and DCESerial Cable

Assembly andPinouts

Figure B-4 shows the V.35 serial cable assembly. Table B-8 lists the DTE cable pinouts (Part Number ERMV35-CAB). Table B-9 lists the DCE cable pinouts (Part Number ERFV35-CAB). Arrows in the tables indicate signaldirection:



Figure B-4 V.35 Serial Cable Assembly

J1-46J1-45J1-16J1-15

J1-1J1-30J1-31J1-60



J2-BJ2-DJ2-AJ2-C

J2-KKJ2-MMJ2-LLJ2-NN

34


Table B-8 V.35 DTE Cable Pinouts (DB-60 to Winchester-Type 34-Pin)


J1-49J1-48

MODE_1GND


J1-50J1-51J1-52

MODE_0GNDMODE_DCE


J1-53J1-54J1-55J1-56

TxC/NILRxC_TxCERxD/TxDGND


J1-46 Shield_GND Single — J2-A Frame GND

J1-45Shield

Circuit_GND—


J2-BShield

Circuit GND—

J1-42Shield

RTS/CTS—


J2-CShield

RTS—

J1-35Shield

CTS/RTS—


J2-DShield

CTS—

J1-34Shield

DSR/DTR—


J2-EShield

DSR—

J1-33Shield

DCD/LL—


J2-FShield

RLSD—

J1-43Shield

DTR/DSR—


J2-HShield

DTR—

J1-44Shield

LL/DCD—


J2-KShield

LT—

J1-18J1-17

TxD/RxD+TxD/RxD-


J2-PJ2-S

SD+SD-

J1-28J1-27

RxD/TxD+RxD/TxD-


J2-RJ2-T

RD+RD-

J1-20J1-19

TxCE/TxC+TxCE/TxC-


J2-UJ2-W

SCTE+SCTE-

J1-26J1-25

RxC/TxCE+RxC/TxCE-


J2-VJ2-X

SCR+SCR-

J1-24J1-23

TxC/RxC+TxC/RxC-


J2-YJ2-AA

SCT+SCT-



Table B-9 V.35 DCE Cable Pinouts (DB-60 to Winchester-Type 34-Pin)


J1-49J1-48

MODE_1GND

Shorting group — — —

J1-50J1-51

MODE_0GND


J1-53J1-54J1-55J1-56

TxC/NILRxC_TxCERxD/TxDGND


J1-46 Shield_GND Single — J2-A Frame GND

J1-45Shield

Circuit_GND—


J2-BShield

Circuit GND—

J1-35Shield

CTS/RTS—


J2-CShield

RTS—

J1-42Shield

RTS/CTS—


J2-DShield

CTS—

J1-43Shield

DTR/DSR—


J2-EShield

DSR—

J1-44Shield

LL/DCD—


J2-FShield

RLSD—

J1-34Shield

DSR/DTR—


J2-HShield

DTR—

J1-33Shield

DCD/LL—


J2-KShield

LT—

J1-28J1-27

RxD/TxD+RxD/TxD-


J2-PJ2-S

SD+SD-

J1-18J1-17

TxD/RxD+TxD/RxD-


J2-RJ2-T

RD+RD-

J1-26J1-25

RxC/TxCE+RxC/TxCE-


J2-UJ2-W

SCTE+SCTE-

J1-22J1-21

NIL/RxC+NIL/RxC-


J2-VJ2-X

SCR+SCR-

J1-20J1-19

TxCE/TxC+TxCE/TxC-


J2-YJ2-AA

SCT+SCT-



X.21 DTE and DCESerial Cable Pinouts

(DB-15)

Figure B-5 shows the X.21 serial cable assembly. Table B-10 lists the DTE cable pinouts (Part Number ERMX21-CAB). Table B-11 lists the DCE cable pinouts (Part Number ERFX21-CAB). Arrows in the tables indicate signal direction:



Figure B-5 X.21 Cable Assembly

H19

74



J2-8J2-15

J2-9J2-1

J1-46J1-45J1-16J1-15

J1-1J1-30J1-31J1-60

Table B-10 X.21 DTE Cable Pinouts (DB-60 to DB-15)


J1-48J1-47

GNDMODE_2


J1-51J1-52

GNDMODE_DCE



J1-11J1-12

TxD/RxD+TxD/RxD-


J2-2J2-9

Transmit+Transmit-

J1-9J1-10

RTS/CTS+RTS/CTS-


J2-3J2-10

Control+Control-

J1-28J1-27

RxD/TxD+RxD/TxD-


J2-4J2-11

Receive+Receive-

J1-1J1-2

CTS/RTS+CTS/RTS-


J2-5J2-12

Indication+Indication-

J1-26J1-25

RxC/TxCE+RxC/TxCE-


J2-6J2-13

Timing+Timing-

J1-15Shield

Control_GND—

Twisted pair no. 4 — J2-8Shield

Control GND—



Table B-11 X.21 DCE Cable Pinouts (DB-60 to DB-15)


J1-48J1-47

GNDMODE_2



J1-28J1-27

RxD/TxD+RxD/TxD-


J2-2J2-9

Transmit+Transmit-

J1-1J1-2

CTS/RTS+CTS/RTS-


J2-3J2-10

Control+Control-

J1-11J1-12

TxD/RxD+TxD/RxD-


J2-4J2-11

Receive+Receive-

J1-9J1-10

RTS/CTS+RTS/CTS-


J2-5J2-12

Indication+Indication-

J1-24J1-23

TxC/RxC+TxC/RxC-


J2-6J2-13

Timing+Timing-

J1-15Shield

Control_GND—


J2-8Shield

Control GND—

J1-48J1-47

GNDMODE_2



C
VIRTUAL CONFIGURATION REGISTER
The CoreBuilder™ 5000 Network Router Module has a 16-bit virtual configuration register, which is written into the nonvolatile random-access memory (NVRAM).

This appendix describes the virtual configuration register (VCR), the factory-default settings for the register, and the procedures for changing those settings.

This appendix contains the following sections:

■ VCR Tasks

■ VCR Bit Definitions

■ Changing VCR Settings

■ Enabling Booting From Flash Memory

VCR Tasks Use the virtual configuration register to perform the following tasks:

■ Set and display the configuration register value

■ Force the system into bootstrap mode

■ Select a boot source and default boot filename

■ Enable or disable the Break function

■ Control broadcast addresses

■ Set the console terminal baud rate

■ Load operating software from ROM

■ Enable booting from a TFTP (Trivial File Server Protocol) server

C-2 VIRTUAL CONFIGURATION REGISTER

VCR Bit Definitions Table C-1 defines each of the virtual configuration register memory bits.

To avoid confusion and possibly disabling the router, remember that valid register settings may be combinations of settings and not just the individual settings listed in Table C-1. For example, the factory-default value of 0x2102 is a combination of settings.

* The factory-default value for the configuration register is 0x2102. This value is acombination of settings (bit 13 = 0x2000, bit 8 = 0x0100, and bits 00 through 03 =0x0002).

Boot Field The lowest four bits of the virtual configuration register (bits 3, 2, 1, and 0) form the boot field. The boot field specifies a binary number. Table C-2 defines the boot field binary values.

Table C-1 Virtual Configuration Register Bit Values

Bit No.* Hex Value Meaning

00 to 03 0x0000 to 0x000F

Boot field

06 0x0040 Causes system software to ignore NVRAM contents

07 0x0080 OEM bit enabled

08 0x0100 Break function disabled

09 — Unused

10 0x0400 IP broadcast with all zeros

11 to 12 0x0800 to 0x1000

Engine management terminal baud rate

13 0x2000 Boot default ROM software if network boot fails

14 0x4000 IP broadcasts do not have net numbers

15 0x8000 Enable diagnostic messages and ignore NVRAM contents

Table C-2 Boot Field Values (Configuration Register Bits 00 to 03)

Bit Boot Field Meaning

0 0x1 Stays at the system bootstrap prompt.

1 0x2 Boots system image in system ROM.

2 to 3 0x4 to 0xF Specifies a default netboot filename and enables boot system commands that override the default netboot filename.

VCR Bit Definitions C-3

Setting Boot Field Values

To set the boot field values:

■ If you set a boot field value to 0, you must boot the operating system manually. To boot the operating system manually, enter the B command at the bootstrap prompt:

> b [tftp] flash IJ09140Z

For more information on the B command, refer to the Cisco Systems Router Products Configuration Guide.

■ If you set the boot field value to a value in the range of 0x2 through 0xF, and a valid system boot command is stored in the configuration file, then the router module boots the system software as directed by that value.

■ If you set the boot field to any other bit pattern, the router module uses the resulting number to form a default boot filename for netbooting (refer to Default Boot Filenames on page C-3).

In the following example, the virtual configuration register is set to boot the router module from Flash memory and to ignore the Break function at the next reboot of the router module:

router# configure terminalEnter configuration commands, one per line.Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Zconfig-register 0x102boot system flash IJ09140Z^Zrouter#

Default Boot Filenames

The network server creates a default boot filename as part of the automatic configuration process and stores the binary value in the virtual configuration register.

To form the boot filename, the server starts with cisco and links the octal equivalent of the boot field number, a hyphen, and the processor-type name. Table C-3 lists the default boot filenames or actions for the processor.


A boot system configuration command in the router module configuration in NVRAM overrides the default netboot filename.

Break Function Bit 8 controls the way the server interprets the engine management terminal Break key. The server interprets the Break key in the following ways:

■ Setting bit 8 (the factory default) causes the processor to ignore the console Break key.

■ Clearing bit 8 causes the processor to interpret the Break key as a command to force the system into the bootstrap monitor, which halts normal operation. A Break command can be sent during the first 60 seconds of a system reboot, regardless of the configuration settings.

Table C-3 Default Boot Filenames

Action/Filename Bit 3 Bit 2 Bit 1 Bit 0

bootstrap mode 0 0 0 0

ROM software 0 0 0 1

cisco2-4500 0 0 1 0

cisco3-4500 0 0 1 1

cisco4-4500 0 1 0 0

cisco5-4500 0 1 0 1

cisco6-4500 0 1 1 0

cisco7-4500 0 1 1 1

cisco10-4500 1 0 0 0

cisco11-4500 1 0 0 1

cisco12-4500 1 0 1 0

cisco13-4500 1 0 1 1

cisco14-4500 1 1 0 0

cisco15-4500 1 1 0 1

cisco16-4500 1 1 1 0

cisco17-4500 1 1 1 1

VCR Bit Definitions C-5

Internet ProtocolBroadcast Address

Bit 10 controls the host portion of the Internet Protocol (IP) broadcast address as follows:

■ Setting bit 10 causes the processor to use all zeros.

■ Clearing bit 10 (the factory default) causes the processor to use all ones.

Bit 10 interacts with bit 14, which controls the network and subnet portions of the broadcast address. Table C-4 lists the combined effect of bits 10 and 14.

Engine ManagementTerminal Baud Rate

Bits 11 and 12 determine the baud rate of the engine management terminal.

Table C-5 lists the bit settings for the four available baud rates. The factory-set default baud rate is 9600.

Bootload FailureResponse

Bit 13 determines the server response to a bootload failure as follows:

■ Setting bit 13 causes the server to load operating software from ROM after five unsuccessful attempts to load a boot file from the network.

■ Clearing bit 13 causes the server to continue attempting to load a boot file from the network indefinitely. The default setting for bit 13 is cleared.

Table C-4 Broadcast Address Destination Settings

Bit 14 Bit 10 Address (<net> <host>)

Off Off <ones> <ones>

Off On <zeros> <zeros>

On On <net> <zeros>

On Off <net> <ones>

Table C-5 Engine Management Terminal Baud Rate Settings

Baud Bit 12 Bit 11

9600 0 0

4800 0 1

1200 1 0

2400 1 1


NVRAM Disable Bit 15 determines whether or not the server uses the contents of NVRAM as follows:

■ Setting bit 15 causes the server to ignore the configuration file in NVRAM and to enable diagnostic messages.

■ Clearing bit 15 causes the server to use the contents of NVRAM.

Changing VCR Settings

To change the values in the configuration register while running the system software:

1 Enter the ENABLE command and your password to enter the privileged level.

router> enablePassword:router#

2 At the privileged-level system prompt (router#), enter the CONFIGURE TERMINAL command. The system displays information about the configuration commands.

router# configure terminalEnter configuration commands, one per line.Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Z

3 To set the contents of the configuration register, enter the CONFIG-REGISTER command, where yyyy is a hexadecimal number preceded by 0x (refer to the Note on page C-2).

config-register 0xyyyy

4 Exit configuration mode by pressing Ctrl-Z. The new value settings are saved to memory. However, the new settings do not take effect until the system software reloads when the router module engine reboots.

5 To display the configuration register value currently in effect and the value that will be used at the next reload, enter the exec mode SHOW VERSION command. The value appears on the last line of the screen display as in the following example:

Configuration register is 0x142 (will be 0x102 at next reload)

6 Reboot the router module engine. The new value takes effect.

Enabling Booting From Flash Memory C-7

Configuration register changes take effect only when the server restarts. To restart the server, power off and then power on the router module or issue a reload command from the engine management terminal.

Enabling Booting From Flash Memory

To enable booting from Flash memory, set configuration register bits 3, 2, 1, and 0 to a value between 2 and 15.

To enter configuration mode, while in the system software image specify a Flash filename from which to boot. For example:

router# configure terminalEnter configuration commands, one per line.Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Zboot system flash IJ09140Z

To disable the Break key and enable the BOOT SYSTEM FLASH command, enter the CONFIG-REGISTER command with the value shown in the following example:

router# configure terminalEnter configuration commands, one per line.Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Zconfig-reg 0x2102^Zrouter#

D
FDDI PRECAUTIONS
The information in this appendix is a requirement of the CDRH division of the FDA. This appendix contains the following sections:

■ FDDI Laser Safety Information

■ Processing

FDDI Laser Safety Information

The FDDI components in the CoreBuilder™ 5000 Network Router Module comply with the following standards for CLASS 1 LASER safety:

■ 21 CRF 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA)

■ IEC Publications 825 (International Electrotechnical Commission)

■ CENELEC EN 60825 (European Committee for Electrotechnical Standardization)

When operated within its performance specification limits, the laser transceiver output meets the CLASS 1 accessible emission limit of all three standards. Class 1 levels of laser radiation are not considered to be hazardous.

The use of optical instruments increases eye hazard. When viewing the output optical port the power must be removed from the transmitter section.

The label in Figure D-1 satisfies the safety certification requirements for the CoreBuilder 5000 Network Router Module.

D-2 FDDI PRECAUTIONS

Figure D-1 Required Class 1 Laser Product Label

Processing The Laser transceiver may be wave soldered and aqueous rinsed as long as the process plug, provided with each unit, is properly installed on the units optical port. The transceiver case may not be exposed to solvents such as 1-1-1 - trichloroethane, acetone, methyl ethyl ketone, or trichloroethylene. The transceiver pins may be wave-soldered at 240 oC for up to 10 seconds. The transceiver case deformation temperature is 160 oC.

CLASS 1 LASER PRODUCT

IEC 825, Class 1 LED Device. For connection only to Class 1 LED Devices.

E
TECHNICAL SUPPORT
3Com provides access to technical support information through a variety of services. This appendix describes these services.

Information contained in this appendix is correct at time of publication. For the very latest, access 3Com Corporation’s World Wide Web site as described below.

This appendix describes:

■ Online Technical Services

■ Support From Your Network Supplier

■ Support From 3Com Corporation

■ Returning Products for Repair

■ Accessing the 3Com MIB

■ Contacting 3Com Technical Publications

Online Technical Services

3Com offers worldwide product support 24 hours a day, 7 days a week, through the following online systems:

■ World Wide Web Site

■ 3Com Bulletin Board Service

■ 3ComFacts Automated Fax Service

■ 3ComForum on CompuServe Online Service

E-2 TECHNICAL SUPPORT

World Wide Web Site Access the latest networking information on 3Com Corporation’s World Wide Web site by entering our URL into your Internet browser:

http://www.3Com.com/

This service features news and information about 3Com products, customer service and support, 3Com Corporation’s latest news releases, NetAge Magazine, and more.

3Com Bulletin BoardService

3ComBBS contains patches, software, and drivers for all 3Com products, as well as technical articles. This service is available through modem or ISDN 24 hours a day, 7 days a week.

Access by Analog Modem

To reach the service by modem, set your modem to 8 data bits, no parity, and 1 stop bit. Call the telephone number nearest you:

Access by Digital Modem

ISDN users can call 3ComBBS using a digital modem for fast access up to 56 Kbps. To access 3ComBBS using ISDN, use the following number:

408 654 2703

Country Data Rate Telephone Number

Australia up to 14400 bps 61 2 9955 2073

Brazil up to 14400 bps 55 11 547 9666

France up to 14400 bps 33 1 6986 6954

Germany up to 28800 bps 4989 62732 188

Hong Kong up to 14400 bps 852 2537 5608

Italy (fee required) up to 14400 bps 39 2 27300680

Japan up to 14400 bps 81 3 3345 7266

Mexico up to 28800 bps 52 5 520 7853

P. R. of China up to 14400 bps 86 10 684 92351

Singapore up to 14400 bps 65 534 5693

Taiwan up to 14400 bps 886 2 377 5840

U.K. up to 28800 bps 44 1442 438278

U.S.A. up to 28800 bps 1 408 980 8204

Online Technical Services E-3

3ComFactsAutomated Fax

Service

3Com Corporation’s interactive fax service, 3ComFactsSM, provides data sheets, technical articles, diagrams, and troubleshooting instructions on 3Com products 24 hours a day, 7 days a week.

Call 3ComFacts using your Touch-Tone telephone using one of these international access numbers:

Local access numbers are available within the following countries:

3ComForum onCompuServe Online

Service

3ComForum is a CompuServe-based service containing patches, software, drivers, and technical articles about 3Com products, as well as a messaging section for peer support. To use 3ComForum, you need a CompuServe® account.

To use 3ComForum:

1 Log on to CompuServe.

2 Type go threecom

3 Press Return to view the 3ComForum main menu.

Country Telephone Number

Hong Kong 852 2537 5610

U.K. 44 1442 278279

U.S.A. 1 408 727 7021

CountryTelephone Number Country

Telephone Number

Australia 1 800 123853 Netherlands 06 0228049

Belgium 0800 71279 Norway 800 11062

Denmark 800 17319 Portugal 0505 442 607

Finland 98 001 4444 Russia (Moscow only) 956 0815

France 05 90 81 58 Spain 900 964 445

Germany 0130 81 80 63 Sweden 020 792954

Italy 1678 99085 U.K. 0800 626403


Support From Your Network Supplier

If additional assistance is required, contact your network supplier. Several suppliers are authorized 3Com service partners who are qualified to provide a variety of services, including network planning, installation, hardware maintenance, application training, and support services.

If you contact your network supplier for assistance, have the following information ready:

■ Diagnostic error messages

■ A list of system hardware and software, including revision levels

■ Details about recent configuration changes, if applicable

If you are unable to contact your network supplier, refer to the following section on how to contact 3Com.

Support From 3Com Corporation E-5

Support From 3Com Corporation

If you are unable to receive support from your network supplier, technical support contracts are available from 3Com.

Contact your local 3Com sales office to locate your authorized service provider using one of the following numbers:

Regional Sales Office Telephone Number Regional Sales Office Telephone Number

3Com CorporationU.S.A.

3Com ANZAEastWest

3Com Asia LimitedChina

Hong KongIndiaIndonesiaKoreaMalaysiaSingaporeTaiwanThailand

3Com Benelux B.V.BelgiumNetherlands

3Com CanadaCalgaryMontrealOttawaTorontoVancouver

3Com France

3Com GmbHAustriaCzech and Slovak RepublicsGermany

HungaryPolandSwitzerland

800 NET 3Com or1 408 764 5000

61 2 9937 500061 3 9866 8022

86 10 68492 568 (Beijing)86 21 6374 0220 Ext 6115 (Shanghai)852 2501 111191 11 644 397462 21 523 918182 2 319 471160 3 732 791065 538 9368886 2 377 5850662 231 8151 4

32 725 020231 30 6029700

403 265 3266514 683 3266613 566 7055416 498 3266604 434 3266

33 1 69 86 68 00

43 1 513432342 2 21845 80049 30 3498790 (Berlin)49 89 627320 (Munich)36 1 250 83 4148 22 645135141 31 996 14 14

3Com Ireland

3Com Japan

3Com Latin AmericaArgentinaBrazilChileColombiaMexicoPeruVenezuela

3Com MediterraneoItaly

3Com Middle East

3Com Nordic ABDenmarkFinlandNorwaySweden

3Com Russia

3Com South Africa

3Com UK Limited

353 1 820 7077

81 3 3345 7251

54 1 312 326655 11 546 086956 2 633 924257 1 629 411052 5 520 784151 1 221 539958 2 953 8122

39 2 253011 (Milan)39 6 5279941 (Rome)

971 4 349049

45 39 27 85 00358 0 435 420 6747 22 18 40 0346 8 632 56 00

007 095 2580940

27 11 807 4397

44 131 2478558 (Edinburgh)44 161 8737717 (Manchester)44 1628 897000 (Marlow)


Returning Products for Repair

Before you send a product directly to 3Com for repair, you must first obtain a Return Materials Authorization (RMA) number. Products sent to 3Com without RMA numbers are returned to the sender unopened, at the sender’s expense.

To obtain an RMA number, call or fax:

Accessing the 3Com MIB

The 3Com Management Information Base (MIB) describes commands that enable you to manage 3Com SNMP-based products. The MIB is available over the Internet on an anonymous FTP server. Updates to these MIBs are released as new 3Com products are introduced.

To access Internet versions:

1 FTP to ftp.3com.com (151.104.9.65).

2 Enter the login name anonymous .

3 Enter your full Internet e-mail address as the password(for example, [email protected] ).

4 Change to the /pub/mibs directory using the command cd/pub/mibs .

5 Read the readisd.txt file to determine the MIB or MIBs you need to manage your 3Com products.

6 To view the 3Com MIB, OID, or schema entries, enter the ls command.

■ To pause the display, press Ctrl+S.

■ To continue the display, press Ctrl+Q.

7 Copy the MIB, OID, or schema files to your current directory using the appropriate command (for example, get isd.mib ).

8 Exit the FTP session using the quit command.

Country Telephone Number Fax Number

U.S.A. and Canada 1 800 876 3266, option 2 408 764 7120

Latin America 1 408 326 7801 408 764 7120

Europe, South Africa and Middle East

44 1442 438125 44 1442 435822

Outside Europe, U.S.A., and Canada

1 408 326 7804 1 408 764 7120

Contacting 3Com Technical Publications E-7

Contacting 3Com Technical Publications

If you have comments or questions on 3Com Technical Publications documents, contact the Technical Publications group by fax at (508) 229-1551.

02/06/97

INDEX

Numerics3Com Bulletin Board Service (3ComBBS) E-23Com parameters 3-83Com sales offices E-53Com URL E-23ComFacts E-33ComForum E-3

AATM

connecting the NIM 2-14connections 2-14LEDs 4-9

Audience of Manual 1Auxiliary port

connections 3-3

Bb (boot) command C-3Base model 1-3Baud-rate settings C-5Boot field C-4Boot System command 5-5, C-4Boot System Flash command C-7Booting

from Flash memory C-7Bootload-failure response C-5Break (interrupt) command C-4bulletin board service E-2

CCable

auxiliary port B-2console port B-2DCE 5-2DTE 5-2EIA/TIA-232 DTE/DCE B-6EIA/TIA-449 DTE/DCE B-9EIA-530 DTE B-4multi-mode fiber-optic 2-9single mode fiber-optic 2-10V.35 DTE/DCE B-12

X.21 DTE/DCE B-15Cisco commands

b (boot) C-3Boot System 5-5, C-4Boot System Flash C-7Break (interrupt) C-4Config-register C-3, C-6, C-7Configure Terminal C-3, C-6Enable 5-5, C-6Flash-related C-2i (initialize) 5-4o/r (reset) 5-4Reload C-7Show Configuration 5-5Show Version C-6

Cisco parameters 3-3 to 3-7CiscoWorks 1-9Commands

Ciscosee Cisco commands

DMMsee DMM commands

Compression 1-9CompuServe E-3Config-register command C-3, C-6, C-7Configuration 3-2 to 3-8

3Com parameters 3-8Cisco NIM connections 3-3Cisco parameters 3-3 to 3-7displaying 4-10 to 4-12network connection 3-8NVRAM 3-2overview 3-1unmanaged hub 3-2

Configure Terminal command C-3, C-6Connections

ATM 2-14auxiliary port 3-3console port 3-2FDDI MM, DAS 2-9FDDI MM, SAS 2-10FDDI SM, DAS 2-11management terminal 3-2NIM 2-8 to 2-13optical bypass switch 2-11Quad Serial 2-13

2 INDEX

Connectorauxiliary port 3-3console port 3-2FC type 2-12MIC type 2-9

Console portconnections 3-2settings C-5troubleshooting 5-3

conventionstext, About This Guide 3

CoreBuilder 5000 Network Router Modulearchitecture 1-2configuration 3-2 to 3-8FDDI support 1-6functions 1-1hot swap capability 1-10models 1-3network control 1-9network management 1-9precautionary procedures 2-1product description 1-1purposes 1-1quick installation 2-2reliability 1-10typical applications 1-5unpacking 2-2WAN support 1-6

DDAS

multi-mode 2-9single mode 2-11

Data compression 1-9DCE cable 5-2Desktop plus IBM software feature set 1-7Desktop software feature set 1-7Dial-on-demand routing 1-9DIP switch

restoring base board positions 2-4DMM commands

SHOW MODULE 4-10SHOW MODULE VERBOSE 4-11SHOW PORT 4-11SHOW PORT VERBOSE 4-12SHOW VERSION 5-4

DTE cable 5-2Dual Attachment Station

see DAS

EEIA/TIA-232 DTE/DCE cable pinouts B-6EIA/TIA-449 DTE/DCE cable pinouts B-9EIA-530 DTE cable pinouts B-4Electrical specifications A-3Electrostatic discharge

precautionary procedures 2-1Enable command 5-5, C-6Enterprise software feature set 1-7Environmental specifications A-3

Ffax service. See 3ComFactsFC connector 2-12FCC notice iiFDDI

connecting the MM, DAS model 2-9connecting the MM, SAS model 2-10connecting the SM, DAS model 2-11laser safety information D-1multi-mode fiber 1-6precautions D-1single-mode fiber 1-6supported interfaces 1-6

FDDI MM, DAS model 1-3FDDI MM, SAS model 1-3FDDI SM, DAS model 1-3Filenames

default for netbooting C-4Flash memory

booting from C-7Flash-related commands C-2

GGeneral specifications A-2

HHardware components 1-2Hot swap capability 1-10, 2-7

Ii (initialize) command 5-4Installation

grounding techniques 2-1hot swap capability 2-7preparations 2-4procedure 2-7quick 2-2

INDEX 3

InterfacesCisco 3-1relation to 3Com ports 3-1

Internet Protocolsee IP

Interruptsee Break (interrupt) command

IP broadcast addressIP/IPX software feature set 1-7

JJumper plugs

restoring base board positions 2-4restoring CPU board positions 2-6

KKey, Break (interrupt) C-4

LLaser safety D-1

certification label D-1LEDs

ATM 4-9common 4-1FDDI 4-6monitoring 4-1 to 4-8Quad Serial 4-7, 4-9

MMechanical specifications A-3Memory specifications A-2MIBs

3Com E-6MIC connector 2-9Models 1-3

base 1-3FDDI MM, DAS 1-3FDDI MM, SAS 1-3FDDI SM, DAS 1-3Quad Serial 1-3

Multi-mode fiber FDDI interface 1-6

NNetboot C-4

default filenames C-4Network

control 1-9Network connection

configuration 3-8

Network Interface Connectionssee NIM

Network management 1-9attaching a terminal 3-2TELNET 1-9

network supplier support E-4NIM

architecture 3-3ATM 2-14configuration 3-3connecting the ATM model 2-14connecting the Quad Serial model 2-13connections 2-8 to 2-13FDDI MM, DAS 2-9FDDI MM, SAS 2-11FDDI SM, DAS 2-10

Non-volatile random access memorysee NVRAM

NVRAMCisco C-6configuration 3-2

Oo/r (reset) command 5-4Online technical services E-1Operating malfunctions 5-3, 5-4Optical bypass switch 2-11

PParameters

Cisco 3-3 to 3-7Password

recovering 5-4Pinouts

auxiliary port cable B-2console port cable B-2EIA/TIA-232 DTE/DCE serial cable B-6EIA/TIA-449 DTE/DCE serial cable B-9EIA-530 DTE serial cable B-4V.35 DTE/DCE serial cable B-12X.21 DTE/DCE serial cable B-15

Ports3Com 3-1relation to Cisco interfaces 3-1

Precautionary procedures 2-1Protocol translation 1-7Protocols supported

FDDI 1-6WAN 1-6

4 INDEX

QQuad Serial

connections 2-13Quad Serial model 1-3

RRecovering a lost password 5-4Reliability 1-10Reload command C-7returning products for repair E-6Routing

dial-on-demand 1-9

SSAS

Multi-mode 2-10Show Configuration Cisco command 5-5SHOW MODULE command 4-10SHOW MODULE VERBOSE command 4-11SHOW PORT command 4-11SHOW PORT VERBOSE command 4-12Show Version Cisco command C-6SHOW VERSION command 5-4Simple Network Management Protocol

see SNMPSimple Network Management Protocol (SNMP)

commands E-6Single Attachment Station

see SASSingle mode fiber FDDI interface 1-6SNMP 1-9SNMP. See Simple Network Management ProtocolSoftware

loading from Flash memory C-7Software feature sets 1-7 to 1-8

Desktop 1-7Desktop plus IBM 1-7Enterprise 1-7IP/IPX 1-7

Specificationselectrical A-3environmental A-3general A-2mechanical A-3memory A-2

Systemsoftware C-7

Ttechnical support E-1

3Com URL E-2bulletin board service E-2fax service E-3network suppliers E-4product repair E-6using CompuServe E-3

TELNET 1-9verifying port configurations 5-3

Troubleshootingconsole port 5-3network connection 5-2operating malfunctions 5-3, 5-4software 5-1startup 5-1WAN connections 5-2

Typical applicationsFDDI model 1-5

UUnpacking 2-2URL E-2

VV.35 DTE/DCE cable pinouts B-12Virtual Configuration Register 5-5

bit definitions C-2 to C-6boot field C-4changing C-3, C-6

WWorld Wide Web E-2WWW E-2

XX.21 DTE/DCE cable pinouts B-15

3Com Corporation LIMITED WARRANTY

For purposes of this warranty, the CoreBuilder 5000 Network Router Module is considered an Internetworking product.

HARDWARE 3Com warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following lengths of time from the date of purchase from 3Com or its Authorized Reseller:

If a product does not operate as warranted above during the applicable warranty period, 3Com shall, at its option and expense, repair the defective product or part, deliver to Customer an equivalent product or part to replace the defective item, or refund to Customer the purchase price paid for the defective product. All products that are replaced will become the property of 3Com. Replacement products may be new or reconditioned. Any replaced or repaired product or part has a 90-day warranty or the remainder of the initial warranty period, whichever is longer.

3Com shall not be responsible for any software, firmware, information, or memory data of Customer contained in, stored on, or integrated with any products returned to 3Com for repair, whether under warranty or not.

SOFTWARE 3Com warrants that the software programs licensed from it will perform in substantial conformance to the program specifications therefor for a period of 90 days from the date of purchase from 3Com or its Authorized Reseller. 3Com warrants the media containing software against failure during the warranty period. No updates are provided. 3Com’s sole obligation with respect to this express warranty shall be (at 3Com’s discretion) to refund the purchase price paid by Customer for any defective software products, or to replace any defective media with software which substantially conforms to 3Com’s applicable published specifications. Customer assumes responsibility for the selection of the appropriate applications program and associated reference materials. 3Com makes no warranty or representation that its software products will work in combination with any hardware or applications software products provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. For any third-party products listed in the 3Com software product documentation or specifications as being compatible, 3Com will make reasonable efforts to provide compatibility, except where the noncompatibility is caused by a “bug” or defect in the third party’s product.

STANDARD WARRANTY SERVICE

Standard warranty service for hardware products may be obtained by delivering the defective product, accompanied by a copy of the dated proof of purchase, to 3Com’s Corporate Service Center or to an Authorized 3Com Service Center during the applicable warranty period. Standard warranty service for software products may be obtained by telephoning 3Com’s Corporate Service Center or an Authorized 3Com Service Center, within the warranty period. Products returned to 3Com’s Corporate Service Center must be pre-authorized by 3Com with a Return Material Authorization (RMA) number marked on the outside of the package, and sent prepaid, insured, and packaged appropriately for safe shipment. The repaired or replaced item will be shipped to Customer, at 3Com’s expense, not later than 30 days after receipt of the defective product by 3Com.

WARRANTIES EXCLUSIVE IF A 3COM PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT 3COM’S OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. 3COM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, OR USE OF ITS PRODUCTS.

Internetworking products 1 year

Network adapters Lifetime

Ethernet stackable hubs and Unmanaged Ethernet fixed port repeaters Lifetime* (1 year if not registered)

*Power supply and fans in the stackable hubs and unmanaged repeaters 1 year

Other hardware products 1 year

Spare parts and spares kits 90 days

3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW, 3COM ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF 3COM OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT 3COM’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers, so the above limitations and exclusions may be limited in their application to you. This warranty gives you specific legal rights which may vary depending on local law.

GOVERNING LAW This Limited Warranty shall be governed by the laws of the state of California.

3Com Corporation, 5400 Bayfront Plaza, Santa Clara, CA 95052-8145 (408) 764-5000

10/20/96