Copied from GH960 - System-On-Modules | Computer-On-Modules

GHF51Embedded SBC 1.8”

User’s Manual

A-587-M-2022

Copied from GH960

2User's Manual | GHF51

CopyrightThis publication contains information that is protected by copyright. No part of it may be repro-duced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifi-cally disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this docu-ment. Further, the manufacturer reserves the right to revise this publication and make changes to its contents at any time, without obligation to notify any person or entity of such revisions or changes.Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.

© 2020. All Rights Reserved.

TrademarksProduct names or trademarks appearing in this manual are for identification purpose only and are the properties of the respective owners.

FCC and DOC Statement on Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-able protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the re-ceiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:1. The changes or modifications not expressly approved by the party responsible for com-

pliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.


Table of ContentsCopyright ........................................................................................................................................2

Trademarks ....................................................................................................................................2

FCC and DOC Statement on Class B ...........................................................................................2

Notice: ............................................................................................................................................2

About this Manual ......................................................................................................................... 4

Warranty ........................................................................................................................................4

Static Electricity Precautions ....................................................................................................... 4

Safety Measures ...........................................................................................................................4

About the Package........................................................................................................................ 5

Optional Items ...............................................................................................................................5

Before Using the System Board ................................................................................................... 5

Chapter 1 - Introduction................................................................................................................ 6Specifications .........................................................................................................................6Features .................................................................................................................................. 7

Chapter 2 - Hardware Installation ................................................................................................ 8Board Layout........................................................................................................................... 8Standby Power LED ................................................................................................................8System Memory ..................................................................................................................... 9Assembly ................................................................................................................................ 9I/O Connectors .....................................................................................................................10

Rear I/O Ports ................................................................................................................10SMBus ............................................................................................................................11Front Panel .....................................................................................................................11Front Panel Cable Installation ......................................................................................12Battery ............................................................................................................................1312V DC Terminal Block .................................................................................................13Digital I/O .......................................................................................................................14Expansion Slots .............................................................................................................14Installing the Mini PCIe Module ...................................................................................15

Chapter 3 - BIOS Settings ...........................................................................................................16Overview ...............................................................................................................................16Main .......................................................................................................................................17Advanced .............................................................................................................................17

AMD CHIPSET Setting ...................................................................................................18AMD Platform Setting ...................................................................................................19Trusted Computing ........................................................................................................20ACPI Configuration ........................................................................................................20CPU Configuration .........................................................................................................21PC Health Status ...........................................................................................................21WatchDog Configuration ...............................................................................................22USB Configuration .........................................................................................................22Network Stack Configuration........................................................................................23CSM Configuration ........................................................................................................23

Security .................................................................................................................................24Secure Boot ....................................................................................................................24

Boot .......................................................................................................................................25

Save & Exit ............................................................................................................................25Updating the BIOS ................................................................................................................26Notice: BIOS SPI ROM..........................................................................................................26

Chapter 4 - Supported Software ................................................................................................27Auto-run Menu ......................................................................................................................27AMD Chipset and VGA Drivers ............................................................................................27Intel LAN Driver ...................................................................................................................28Gaming Drivers .....................................................................................................................29Adobe Acrobat Reader 9.3 ..................................................................................................30


About this ManualThis manual can be downloaded from the website, or acquired as an electronic file included in the optional CD/DVD. The manual is subject to change and update without notice, and may be based on editions that do not resemble your actual products. Please visit our website or con-tact our sales representatives for the latest editions.

Warranty 1. Warranty does not cover damages or failures that arised from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper in-stallation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-stances, attempt to perform service, adjustments or repairs on the product, whether in or out of warranty. It must be returned to the purchase point, factory or authorized ser-vice agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the product that has been modified or altered.

Static Electricity PrecautionsIt is quite easy to inadvertently damage your PC, system board, components or devices even before installing them in your system unit. Static electrical discharge can damage computer components without causing any signs of physical damage. You must take extra care in han-dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, con-tacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.

Safety Measures• To avoid damage to the system, use the correct AC input voltage range.

• To reduce the risk of electric shock, unplug the power cord before removing the sys-tem chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.

Important:Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD pro-tection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection.


About the PackageThe package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance.

1 GHF51 board

1 Heat spreader (Height: 11mm) A71-808322-000G

1 Screw of Mini PCIe card A32-E12016-050G

Optional ItemsPower adapter / 60W, 12V, DC jack

SMBus cable

Front panel cable

Heat sink for 0~60°C / Height: 29.66mm

Heat sink for -20~70°C / Height: 30.7mm

2-pole terminal to DC Jack cable

DIO cable

The board and accessories in the package may not come similar to the information listed above. This may differ in accordance with the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales representative.

Before Using the System BoardWhen installing the system board in a new system, you will need at least the following internal components.

• Storage device such as hard disk drive, CD-ROM, etc.

• Power adaptor

External system peripherals may also be required for navigation and display, including at least a keyboard, a mouse and a video display monitor.

6

Chapter 1 INTRODUCTION

User's Manual | GHF51

Chapter 1 - Introduction

X Specifications

The specifications listed here may be based on editions that do not resemble your actual products. Please visit the down-load page at go.dfi.com/GHF51, or via the QR code to the right for the latest datasheet.

SYSTEM Processor AMD® Ryzen™ Embedded Processors- R1606G, Dual Core, 1MB Cache, 3 CU, 2.6GHz, 12W- R1505G, Dual Core, 1MB Cache, 3 CU, 2.4GHz, 12W- R1305G, Dual Core, 3 CU, 1.5GHz, 8-10W- R1102G, Dual Core, 3 CU, 1.2GHz, 6W

Memory DDR4 Memory Down up to 4GB/8GBSingle Channel DDR4 2400MHz

BIOS AMI SPI 64Mbit

GRAPHICS Controller AMD Radeon Vega GPU with up to 3 computing units.

Feature H.265 decode/encode support, VP9 decode

Display 2 x Micro HDMI, resolution up to 4096x2160 @ 24Hz

EXPANSION Interface 1 x Full-size Mini PCIe (PCIe Gen2/USB 2.0, optional USB 3.1 Gen2/USB 2.0)

ETHERNET Controller 1 x Intel® I211AT PCIe (10/100/1000Mbps) or1 x Intel® I210IT PCIe (10/100/1000Mbps) (available upon request)

REAR I/O Ethernet 1 x GbE (RJ-45)

USB 1 x Type C USB 3.1 Gen 2

Display 2 x Micro HDMI (HDMI 1.4)

INTERNAL I/O DIO 1 x 8-bit DIO

SMBus 1 x SMBus

STORAGE eMMC 1 x 16GB/32GB/64GB eMMC

WATCHDOG TIMER Output & Interval Software reset, Programmable via Software from 1 to 65535 Seconds

SECURITY TPM fTPM 2.0

POWER Type Single 12V +/-5% DC

Connector 2-pin Terminal Block

Consumption Typical: R1505G: 12V @ 0.37A (4.44W)Max: R1505G: 12V @ 1.74A (20.88W)

RTC Battery CR2032 Coin Cell

OS SUPPORT (UEFI Only)

Microsoft/Linux Windows 10 IoT Enterprise 64-bitLinux (Kernal 5.3)

ENVIRONMENT Temperature Operating: 0 to 60°C / -20 to 70°CStorage: -40 to 85°C

Humidity Operating: 5 to 90% RHStorage: 5 to 90% RH

MECHANICAL Dimensions 1.8" SBC Form Factor: 84mm (3.31") x 55mm (2.17")

7

Chapter 1 INTRODUCTION


X Features

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set time interval. If the system hangs or fails to function, it will reset at the set time interval so that your system will continue to operate.

DDR4 Memory Down

DDR4 delivers increased system bandwidth and improves performance. The advantages of DDR4 provide an extended battery life and improve the performance at a lower power than DDR3/DDR2. The system features memory down instead of using memory sockets for optimal space reduction.

Graphics

The integrated AMD® RadeonTM graphics engine delivers an excellent blend of graphics perfor-mance and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and com-patibility needed for today’s and tomorrow’s business applications.

Gigabit LAN

The Intel® I211AT Gigabit LAN controller features up to 1Gbps data transmission with support for Intel® Active Management Technology. It provides remote maintenance and manageability for networked computing assets in an enterprise environment.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-agement Event) signal. However, if your system is in the Suspend mode, you can power-on the system only through an IRQ or DMA interrupt. USB

The system board supports the new USB 3.1 Gen 2. It is capable of running at a maximum transmission speed of up to 10 Gbit/s (1.2 GB/s) and is faster than USB 3.1 Gen 1 (5 Gbit/s, or 625 MB/s), USB 2.0 (480 Mbit/s, or 60 MB/s) and USB 1.1 (12Mb/s). USB 3.1 reduces the time required for data transmission, reduces power consumption, and is backward compatible with USB 2.0. It is a marked improvement in device transfer speeds between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface) specification. ACPI has energy saving features that enables PCs to implement Power Manage-ment and Plug-and-Play with operating systems that support OS Direct Power Management. ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM function.With the Suspend to RAM function enabled, you can power-off the system at once by pressing the power button or selecting “Standby” when you shut down Windows® without having to go through the sometimes tiresome process of closing files, applications and operating system. This is because the system is capable of storing all programs and data files during the entire operating session into RAM (Random Access Memory) when it powers-off. The operating ses-sion will resume exactly where you left off the next time you power-on the system.

Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system manually or let the system power-on automatically.

8

Chapter 2 HARDWARE INSTALLATION


Chapter 2 - Hardware Installation

X Board Layout

Important:When the Standby Power LED lights green, it indicates that there is power on the system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and com-ponents.

X Standby Power LED

Important:Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in boards, and other components. Perform installation procedures at an ESD workstation only. If such a station is not available, you can provide some ESD pro-tection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection.

RyzenR1000Series

AMDTM

DDR4

DDR4

eMMC

Intel I211AT

SMBus

Front Panel

126 5

126 5

Buzzer

Mini PCIe

SPI Flash BIOS

DIO

DC 12V

Standby Power LEDUART Debug

HDMI 1 HDMI 2 USB 3.1Gen 2

LAN1

1 Battery

1

2

9

10

DDR4

DDR4

RyzenR1000Series

AMDTM

DDR4

DDR4

eMMC

Intel I211AT

SMBus

Front Panel

126 5

126 5

Buzzer

Mini PCIe

SPI Flash BIOS

DIO

DC 12V

Standby Power LEDUART Debug

HDMI 1 HDMI 2 USB 3.1Gen 2

LAN1

1 Battery

1

2

9

10

DDR4

DDR4

Bottom View

Top View

Standby Power LED

9



• DDR4 2400MHz Single Channel

• Up to 4G or 8G Memory Down

X System Memory

Features

The system board supports the following memory interface.

Single Channel (SC)Data will be accessed in chunks of 64 bits from the memory channels. RAMs are on the same channel.

A heat spreader is included in the standard package. The heat spreader and components re-quired for mounting are illustrated below.

DDR4

DDR4

X Assembly

Chassis

Interface Metal Side Down

CPU Side Up

Screw * 4

Interface Metal

To Chassis

To Chassis

Chassis

Chassis


CPU Side Up

Screw * 4

Interface Metal

To Chassis

To Chassis

Chassis

The heat spreader is designed to be mounted onto the module as illus-trated below. Please make sure the contacting sides of the heat spreader and the module are correct — the CPU side of the module shall be fac-ing the interface metal side and legs of the heat spreader. Rotate horo-zontally so the interface metal sits right on top of the CPU. Remove any plastic cover on the interface metal and apply thermal paste/adhesive if it is required.

Bottom View

Top View

Important:Please do not operate the system with solely the standard heat spreader as the cooling system. Please use a heatsink instead or add to the system a cooling fan for adequate cooling.

10



Chassis


CPU Side Up

Screw * 4

Interface Metal

To Chassis

To Chassis

Chassis

Chassis


CPU Side Up

Screw * 4

Interface Metal

To Chassis

To Chassis

Chassis

X Assembly

Rotate the module and heat spreader combo so that the I/O is facing the desired side, and place the combo in the position of the chassis reserved for your module.

Align the screw holes of the combo to those on the chassis. The combo can be mounted onto the chassis in two manners — 1) module side to the chassis, or 2) heat spreader side to the chassis as illustrated below. This shall depend entirely on the design of the chassis with regard to interior spacing, thermal, and I/O.

Place the screws that come with the standard package into the screw holes, and use a screw driver to fasten the screws until the combo is securely fixed onto the chassis.

� Module side to the chassis � Heat spreader side to the chassis

X I/O Connectors

Bottom View

� USB 3.1 Gen 2, Type C

� LAN

� Micro HDMI 2

� Micro HDMI 1

Rear I/O Ports

• Intel® I211AT PCI Express Gigabit Ethernet controller (alternatively Intel®

I210IT PCI Express Gigabit Ethernet controller)

• 2 x Micro HDMI with resolution up to 4096x2160 @ 24Hz

Features

11



SMBus Front Panel

X I/O Connectors X I/O Connectors

The SMBus (System Management Bus) connector is used to connect the SMBus device. It is a multiple device bus that allows multiple chips to connect to the same bus and enable each one to act as a master by initiating data transfer.

RESET - Reset SwitchThis switch allows you to reboot without having to power off the system.

Power/Standby LEDWhen the system’s power is on, this LED will light up. When the system is in the S1 (POS - Power On Suspend) state, it will blink at 1-second intervals. When the system is in the S3 (STR - Suspend To RAM) state, it will blink at 4-second intervals.

Power ButtonThis switch is used to power on or off the system.

� SMBus Pin Assignment

� Front Panel Pin Assignment

Pin Assignment Pin Assignment

1 N.C. 2 SMBus_Alert

3 SMBus_DATA 4 SMBus_Clock

5 GND 6 3V3SBPin Assignment Pin Assignment

1 N.C. 2 Reset

3 Power LED 4 GND

5 Power LED (3V3SB) 6 Power Button

� SMBus

� Front Panel

Top View Top View

1

56

2

1

56

2

12



Front Panel Cable Installation

X I/O Connectors

The Pin 1 of Front Panel cable should be connected to Front Panel Pin 6 on the motherboard. Due to Pin definition on GHF51 different from other boards, the HDD_LED (Red) doesn’t func-tion.

� Front Panel

Top View

1

56

2

13



Battery

X I/O Connectors

The external lithium ion battery supplies power to the real-time clock and CMOS memory as an auxiliary source of power when the main power is shut off.

Safety Measures

• There exists explosion hazard if the battery is incorrectly installed.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to local ordinances.

� Battery

3.3V21

GND

� External Battery

Connect to board

Bottom View Bottom View

12V DC Terminal Block

X I/O Connectors

Important:Insufficient power supplied to the system may result in instability or malfunction of the add-in boards and peripherals. Calculating the system’s approximate power usage is important to ensure that the power supply meets the system’s consump-tion requirements.

This 2-pin terminal block is considered a low power solution. Connect a DC power cord to this terminal block by inserting the wire into the block and then screw tight the screw on top to secure the wire in place. Please make sure the positive and negative wires are installed cor-rectly. Using a voltage more than the recommended range may fail to boot the system or cause damage to the system board.

Note:An optional DC cable converter can be purchased to convert the 2-pin terminal block to a coaxial DC jack.

1 (+) : +12V

2 (-) : GND

14



Digital I/O

The 8-bit Digital I/O (DIO) connector allows for input/output signals of digi-tal logical states defined by voltage levels. Pin Assignment

1 GND

2 5VSB

3 DIO_0

4 DIO_1

5 DIO_2

6 DIO_3

7 DIO_4

8 DIO_5

9 DIO_6

10 DIO_7

� Digital I/O Pin Assignment

� DIO

Bottom View Bottom View

1 9

2 10

Expansion Slots

Mini PCIeThe Mini PCIe socket allows for a full-size Mini PCIe module, and supports PCIe x1 (Gen3) and USB 2.0 signals.

Mini PCIe

X I/O Connectors X I/O Connectors

Note:A 10-pin cable can be purchased as an optional item for DIO connection.

15



Before installing the Mini PCIe module into the Mini PCIe socket, please make sure that the fol-lowing safety cautions are well-attended.

1. Make sure the PC and all other peripheral devices connected to it has been powered down.

2. Disconnect all power cords and cables.

3. Locate the Mini PCIe socket on the system board

4. Make sure the notch on card is aligned to the key on the socket.

Installing the Mini PCIe Module

X Expansion Slots

Mini PCIe Full Size Mini PCIe Socket

Key

Stand-off

Notch

X I/O Connectors

Please follow the steps below to install the card into the socket.

Step 2:Press the end of the card far from the socket down until against the stand-off.

Step 3:Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying paral-lel to the board when it’s correctly mounted.

Step 1:Insert the card into the socket at an angle while making sure the notch and key are perfectly aligned.

Mini PCIe Half Size Mini PCIe Socket

Key

Stand-off

Notch

16

Chapter 3BIOS SETTING


Chapter 3 - BIOS Settings

Legends

Scroll BarWhen a scroll bar appears to the right of the setup screen, it indicates that there are more avail-able fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

SubmenuWhen “X” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press <Enter>.

Keys Function

Right / Left arrow Move the highlight left or right to select a menu

Up / Down arrow Move the highlight up or down between submenus or fields

<Enter> Enter the highlighted submenu

+ (plus key)/F6 Scroll forward through the values or options of the highlighted field

- (minus key)/F5 Scroll backward through the values or options of the highlighted field

<F1> Display general help

<F2> Display previous values

<F9> Optimized defaults

<F10> Save and Exit

<Esc> Return to previous menu

X Overview

The BIOS is a program that takes care of the basic level of communication between the CPU and peripherals. It contains codes for various advanced features found in this system board. The BIOS allows you to configure the system and save the configuration in a battery-backed CMOS so that the data retains even when the power is off. In general, the information stored in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been made such as a hard drive replaced or a device added.It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need to install a new CMOS battery and reconfigure the BIOS settings.

Default ConfigurationMost of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without re-quiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering the BIOS Setup UtilityThe BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.The BIOS Setup Utility does not require an operating system to run. After you power up the system, the BIOS message appears on the screen and the memory count begins. After the memory test, the message “Press DEL to run setup” will appear on the screen. If the message disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.

Note:The BIOS is constantly updated to improve the performance of the system board; therefore the BIOS screens in this chapter may not appear the same as the actual one. These screens are for reference purpose only.

17



X Main

The Main menu is the first screen that you will see when you enter the BIOS Setup Utility. Ba-sic hardware information is displayed.

System Date

The date format is <month>, <date>, <year>. Press "Tab" to switch to the next field and press "-" or "+" to modify the value.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min-utes from 00 to 59. Second displays seconds from 00 to 59.

Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.

→←: Select Screen↑↓: Select ItemEnter: Select+/- : Change Opt.F1: General HelpF2: Previous ValuesF9: Optimized DefaultsF10: Save & Exit ESC: Exit

SecurityAdvanced Chipset Boot Save & ExitMain

Version 2.20.1273. Copyright (C) 2020 American Megatrends, Inc.

Set the Date. Use Tab to switch between Date ele-ments. Default Ranges:Year: 2005-2099Months: 1-12Days: dependent on month

BIOS InformationProject NameBIOS Version

Memory InformationTotal MemoryMemory SpeedDIMM 0

Processor InformationName

SpeedIDNumber of Processors

System DateSystem Time

GHF51B201.17A

4096 MB (DDR4)2400 MHz4096 MB

AMD Ryzen EmbeddedR1606G with Radeon Vega Gfx2600 MHz00810F814

[Mon 05/07/2020][00:00:00]

X

X::::::

X Advanced

The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Important:Setting incorrect field values may cause the system to malfunction.


→←: Select Screen↑↓: Select ItemEnter: Select+/- : Change Opt.F1: General HelpF2: Previous ValuesF9: Optimized DefaultsF10: Save & ResetESC: Exit

SecurityChipset Boot Save & ExitMain


Advanced

X AMD CHIPSET SettingX AMD Platform SettingX Trusted ComputingX ACPI ConfigurationX CPU ConfigurationX PC Health StatusX WatchDog ConfigurationX USB ConfigurationX Network Stack ConfigurationX CSM Configuration

AMD CBS Setup Page

18






Advanced

AMD CHIPSET Setting

Ac Loss Control

Select among Always On, Always Off, and Last State. This field is used to specify what state the system is set to return to when power is re-applied after AC power failure or loss (G3 state).

Always On The system automatically powers on after power failure.Always Off The system enters soft-off state after power failure. Power-on signal input

is required to power up the system.Last State The system returns to the last state right before power failure.

Se lec t Ac Loss Cont ro l Method

AMD CHIPSET Setting

Ac Loss Control►GFX Configuration►SB USB Configuration

[Always On][Disabled]

X Advanced




Advanced

► GFX Configuration

Integrated Graphics Controller

Configure the integrated graphics controller — Disabled, Forces, or Auto for auto-detection.

UMA Mode

Configure the Unified Memory Architecture (UMA) mode — Auto or UMA_SOECIFIED.

UMA Frame buffer Size

Specify the amount of memory allocation to the integrated GFX — 64M, 128M, 256M, 384M, 512M, 1G, 2G, 3G, or select auto for auto allocation. Please make sure "UMA Mode" is set to "Auto" when a specific size is to be configured.

GFX Configuration

Integrated Graphics ControllerUMA ModeUMA Frame buffer Size

[Auto][Auto][Auto]

Enable Integrated Graphics controller

19






Advanced

AMD Platform Setting

Primary Video Adaptor

Select which graphics controller will be the primary video adaptor — Int Graphics (IGD) or Ext Graphics (PEG).

S e l e c t I n t e r n a l / E x t e r n a l Graphics

Primary Video Adaptor

[Int Graphics (IGD)]

X Advanced X Advanced X AMD CHIPSET Setting




Advanced

► SB USB Configuration

Enable or d isable USB3 controller.

SB USB Configuration

XHCIO Port 0

[Enabled]

XHCIO Port 0

Enable or disable the on-board USB 3.0 controller.

20






Advanced

Trusted Computing

Security Device Support

This field is used to enable or disable BIOS support for the security device such as an TPM 2.0 to achieve hardware-level security via cryptographic keys.

TPM State

Enable or disable the TPM security device. NOTE: Your Computer will rboot during restart in order to change State of the Device.

Pending operation

To clear the existing TPM encryption, select "TPM Clear" and restart the system. This field is not available when "Security Device Support" is disabled.

X Advanced X Advanced

TPM20 Device Found Firmware Version Vendor:

Security Device Support TPM State Pending operation

3.34AMD

[Enable][Enabled][None]

Enables or Disables BIOS support for securi ty de -vice . O.S wi l l not show Security Device. TCG EFI protocol and INT1A inter-face will not be available.




Advanced

ACPI Configuration

Wake On PCIE

Enable or disable Wake-on-LAN function for the integrated LAN to wake up the system.

Wake on RTC

When Enabled, the system will automatically wake up from S5 state at a designated time every day. Once it’s switched to [Enabled], please set up the time of day — hour, minute, and sec-ond — for the system to wake up.

Enable/Disable integrated LAN to wake the system.

Wake On PCIE Wake on RTC Wake up hour Wake up mimute Wake up second

[Disabled][Enabled]000

21






Advanced

CPU Configuration

PSS Support

Enable or disable the power, performance, and speed related ACPI functions of the CPU.

NX Mode

Enable or disable the protection function that keeps no-execute codes from being executed by the CPU.

SVM Mode

Enable or disable Secure Virtual Machine (SVM) for CPU virtualization.

X Advanced

PSS SupportNX ModeSVM Mode

[Enable][Enable][Enable]

Enable/disable the genera-tion of ACPI _PPC, _PSS, and _PCT objets.

This section displays the system’s health information, i.e. voltage readings, CPU and system temperatures, and VCC voltage readings.




Advanced

PC Health Status

X Advanced

Enable/Disable CPU Smart-FanSystem Hardware Monitor

System temperature CPU Temperature VBAT VCore VDDQ

: +63 C: +68 C: +3.032 V: +0.958 V: +1.208 V

22






Advanced

USB Configuration

X Advanced

Enables Legacy USB sup-port. AUTO option disables legacy support if no USB dev ices a re connec ted . DISABLE option will keep USB devices available only for EFI applications.

USB Configuration

USB Module Version

USB Controllers: 1 XHCIUSB Devices: 1 Keyboard, 1 Mouse, 2 Hubs

USB SupportLegacy USB SupportXHCI Hand-offUSB Mass Storage Driver Support

[Enabled][Enabled][Enabled]

Legacy USB Support

Enabled Enable Legacy USB support.

Disabled Keep USB devices available only for EFI applications.

Auto Disable Legacy support if no USB devices are connected.

XHCI Hand-off

Enable or disable XHCI Hand-off.

USB Mass Storage Driver Support

Enable or disable USB Mass Storage Driver Support.




Advanced

WatchDog Configuration

WatchDog1 function

Enable or disable WatchDog function. Once it is enabled, please configure the following field.

SuperIO WatchDog Timer

Set the WatchDog Timer timeout value, ranging from 1 to 255 (second).

X Advanced

WatchDog Confifuration

WatchDog1 function WatchDog1 Timer

[Enabled]20

Enable/Disable WatchDog Timer.

23



CSM Support

This section is used to enable or disable CSM Support. The following fields are only available when "CSM Support" is enabled.

Boot option filter

This field controls Legacy/UEFI ROMs priority — UEFI and Legacy, Legacy only, UEFI only.

Network

This field controls the execution of UEFI and Legacy Network OpROM.

Storage

This field controls the execution of UEFI and Legacy Storage OpROM.

Video

This field controls the execution of UEFI and Legacy Video OpROM.

Other PCI devices

This field determines OpROM execution policy for devices other than Network, Storage or Video.




Advanced

CSM Configuration

X Advanced

Enable/Disable CSM Sup-port.CSM Configuration

CSM Support

Boot option filter

Option ROM execution

NetworkStorageVideoOther PCI devices

[Enabled]

[UEFI only]

[Do not launch][UEFI][UEFI][UEFI]

Network Stack

Enable or disable UEFI network stack. The following fields will appear when this field is en-abled.

Ipv4 PXE Support

Enable or disable IPv4 PXE boot support. If disabled, IPv4 PXE boot support will not be avail-able.

Ipv6 PXE Support

Enable or disable IPv6 PXE boot support. If disabled, IPv6 PXE boot support will not be avail-able.

PXE boot wait time

Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value.

Media detect count

Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value.




Advanced

Network Stack Configuration

X Advanced

Enable/Disable UEFI Net-work StackNetwork Stack

Ipv4 PXE SupportIpv6 PXE SupportPXE boot wait timeMedia detect count

[Enabled][Disabled][Disabled]01

24





Security






Advanced

Administrator Password

Set the administrator password. To clear the password, input nothing and press enter when anew password is asked. Administrator Password will be required when entering the BIOS.

User Password

Set the user password. To clear the password, input nothing and press enter when a new pass-word is asked. User Password will be required when powering up the system.

Set Administrator Pass -word

S e c u r e B o o t a c t i v a t e d when: Secure Boot is ena-bled Platform Key(PK) is enrolled, System mode is User/Deployed, and CSM is disabled

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.The password length must be in the following range:Minimum length Maximum length

Administrator PasswordUser Password

► Secure Boot

System Mode

Secure Boot

Secure Boot Mode► Restore Factory Keys► Reset To Setup Mode

320

Setup

[Disabled]Not Active

[Custom]

X Security

Secure Boot

The Secure Boot store a database of certificates in the firmware and only allows the OSes with authorized signatures to boot on the system. To activate Secure Boot, please make sure that “Secure Boot” is “[Enabled]”, Platform Key (PK) is enrolled, “System Mode” is “User”, and CSM is disabled. After enabling/disabling Secure Boot, please save the configuration and restart the system. When configured and activated correctly, the Secure Boot status will be “Active”.

Secure Boot Mode

Select the secure boot mode — Standard or Custom. When set to Custom, the following fields will be configurable for the user to manually modify the key database.

Restore Factory Keys

Force system to User Mode. Load OEM-defined factory defaults of keys and databases onto the Secure Boot. Press Enter and a prompt will show up for you to confirm.

Reset To Setup Mode

Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm.

Secure Boot

X Security

25







AdvancedAptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.




Advanced

X Boot

Setup Prompt Timeout

Set the number of seconds to wait for the setup activation key. 65535 (0xFFFF) denotes indefi-nite waiting.

Bootup NumLock State

Select the keyboard NumLock state: On or Off.

Quiet Boot

This section is used to enable or disable quiet boot option.

Boot Option Priorities

Rearrange the system boot order of available boot devices. Please enable the devices that you wish to set as boot devices in the "Advanced > CSM Configuration" submenu.

BGRT Logo

It is used to enable or disable the support of display logo with ACPI BGRT table.

The number of seconds that the firmware will wait before booting the original default boot selection.

Boot ConfigurationSetup Prompt TimeoutBootup NumLock State

Boot Option PrioritiesBoot Option #1

Quiet BootBGRT Logo

Save Options Save Changes and Reset Discard Changes and Reset

Default Options Restore Defaults

1[Off][Enabled]

[Windows Boot Manager (MMC - DG4032)]

[Enabled][Enabled]

X Save & Exit

Reset the sys tem a f te r saving the changes

Save Changes and Reset

To save the changes, select this field and then press <Enter>. A dialog box will appear. Select Yes to reset the system after saving all changes made.

Discard Changes and Reset

To discard the changes, select this field and then press <Enter>. A dialog box will appear. Se-lect Yes to reset the system setup without saving any changes.

Restore Defaults

To restore and load the optimized default values, select this field and then press <Enter>. A dia-log box will appear. Select Yes to restore the default values of all the setup options.

Note:If “Boot option filter” of “CSM Configuration” is set to “UEFI and Legacy” or “UEFI only”, and “Quiet Boot” is set to enabled, “BGRT Logo” will show up for configura-tion. Refer to the Advanced > CSM Configuration submenu for more information.

26



X Updating the BIOSTo update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions about how to update BIOS with the flash utility. For updating AMI BIOS in UEFI mode, you may refer to the how-to video at https://www.dfi.com/Knowledge/Video/5.

X Notice: BIOS SPI ROM

1. The Intel® Management Engine has already been integrated into this system board. Due to the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and used on another system board of the same model.

2. The BIOS (SPI ROM) on this system board must be the original equipment from the fac-tory and cannot be used to replace one which has been utilized on other system boards.

3. If you do not follow the methods above, the Intel® Management Engine will not be up-dated and will cease to be effective.

Note:a. You can take advantage of flash tools to update the default configuration of the

BIOS (SPI ROM) to the latest version anytime.b. When the BIOS IC needs to be replaced, you have to populate it properly onto

the system board after the EEPROM programmer has been burned and follow the technical person's instructions to confirm that the MAC address should be burned or not.

27

Chapter 4 SUPPORTED SOFTWARE


Chapter 4 - Supported Software

Install drivers, utilities and software applications that are required to facilitate and enhance the performance of the system board. You may acquire the software from your sales representa-tives, from a DVD included in the shipment, or from the website download page at https://www.dfi.com/DownloadCenter.

X Auto-run Menu

After inserting your DVD-ROM into your optical drive or executing your DVD image, the System Utility auto-run menu may pop up. Click on the utility or driver that is to be installed on the system. Please refer to the following sections that correspond to your selection for more information.

Note:This step can be ignored if the applications are standalone files.

X AMD Chipset and VGA Drivers

1. Read the license agreement then click “Accept and Install”.

2. The step displays the installing status in the progress.

3. After completing installation, click “Restart Now” to exit setup.

Restarting the system will al-low the new software installa-tion to take effect.

28



X Intel LAN Driver

1. Setup is ready to install the driver. Click “Next”.

2. Click “I accept the terms in the license agreement” then click “Next”.

3. Select the program features you want installed then click “Next”.

5. The step displays the installing status in the progress.

4. Click “Install” to begin the in-stallation.

6. After completing installation, click “Finish”.

29



X Gaming Drivers

2. Carefully read the agreement, and then press "I agree" to pro-ceed.

5. The installation is in progress.

3. Choose the components to be installed.

6. The setup is complete. Press "Finish" to close the setup utiil-ity.

1. Setup is ready to install the driver. Click “Next”.

4. Designate a directory where the drivers will be installed, and then press "Install".

30



X Adobe Acrobat Reader 9.3

1. Click “Next” to install or click “Change Destination Folder” to select another folder.

2. Click “Install” to begin installa-tion.

3. Setup is now installing the driver.

4. Click “Finish” to exit installa-tion.

Documents

Copied from GH960 - System-On-Modules | Computer-On-Modules